Series P Internationally Approved Toggles
A96
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable Rockers
Touch Tilt
A
Toggles
www.nkkswitches.com
General Specifications
Electrical Capacity
Resistive Load: 10A @ 125V AC or 6A @ 250V AC
Motor Load: 400W @ 125V AC
Lamp Load: 2A @ 125V AC for On-Off-On circuit & 3A @ 125V AC for other circuits
Other Ratings
Contact Resistance: 10 milliohms maximum
Insulation Resistance: 1,000 megohms minimum @ 500V DC
Dielectric Strength: 2,000V AC minimum between contacts for 1 minute minimum;
4,000V AC minimum between contacts & case for 1 minute minimum
Mechanical Life: 100,000 operations minimum
Electrical Life: 25,000 operations minimum
Angle of Throw: 25°
Materials & Finishes
Toggle Cap: Polypropylene for No Code, Code D; Polyvinyl chloride for Code B (see Ordering Example)
Lever: Brass with chrome plating
Bushing: Brass with nickel plating
Frame: Stainless steel
Case/Base: Diallyl phthalate resin (UL94V-0)
Movable Contacts: Silver alloy with silver plating
Stationary Contacts: Pure silver with silver plating
Terminals: Copper with silver plating
Environmental Data
Operating Temp Range: –10°C through +85°C (+14°F through +185°F)
Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Installation
Soldering Time & Temp: Wave Soldering Recommended (Straight PC): See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards: UL94V-0 rated case/base
UL: File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” to end of part number to order UL recognized switch.
Models with No Code, E, F & D are recognized at 10A @ 125V AC & 6A @ 250V AC.
CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” to end of part number to order CSA certified switch.
Models with No Code, E, F and D are certified at 10A @ 125V AC & 6A @ 250V AC.
VDE: License No. 119174
Models with No Code, B & D are approved at 10A @ 125V AC & 6A @ 250V AC.
Models with No Code, B & D meet EN 61058-1 standard.
8/11/17
Series P
Internationally Approved Toggles
A97
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable
A
Toggles
Rockers
Touch Tilt
www.nkkswitches.com
Distinctive Characteristics
Actual Size
Meets EN 61058-1 standard.
High torque bushing construction prevents rotation or separation
from frame during installation.
Stainless steel frame resists corrosion and increases
environmental safety.
Case/base of heat resistant resin meets UL94V-0
flammability standard.
Contacts of special silver alloy resist arcing and
guarantee stable electrical contact and long life.
High insulating barriers increase isolation of
circuits in double pole devices and provide
added protection to contact points.
Prominent external insulating barriers
increase insulation resistance and dielectric
strength.
Epoxy sealed terminals prevent entry of flux, solvents,
and other contaminants.
Clinching of the frame to the case well above the base and
terminals provides 4,000V dielectric strength.
Series P Internationally Approved Toggles
A98
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable Rockers
Touch Tilt
A
Toggles
www.nkkswitches.com
22
Terminals
No
Code Solder Lug
PStraight PC
Z.187” (4.75mm)
Quick Connect
TYPICAL SWITCH ORDERING EXAMPLE
P20
DPDT
ON-NONE-ON Circuit
Poles & Circuits
11 SPST ON NONE OFF
12 SPDT ON NONE ON
13 SPDT ON OFF ON
21 DPST ON NONE OFF
22 DPDT ON NONE ON
23 DPDT ON OFF ON
Toggles & Bushings
No
Code
.512” (13.0mm) White Cap
with 6mm Bushing
E.450” (11.4mm) Flatted
with 6mm Bushing
B.689” (17.5mm) Large Bat &
AT406B Cap with 12mm Bushing
F.689” (17.5mm) Large Bat
with 12mm Bushing
D.748” (19.0mm) White Capped
Column with 12mm Bushing
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
P2022F
B
.689” (17.5mm) Large Bat
with 12mm Bushing
Solder Lug Terminals
Toggle Position Connected Terminals Throw & Schematics
Pole Model
Down Center Up Down Center Up
Note: Terminal numbers are on
the switch.
SP P2011 ON NONE OFF 1-1b OPEN OPEN SPST
SP P2012
P2013
ON
ON
NONE
OFF
ON
ON 1-1b OPEN 1-1a SPDT
DP P2021 ON NONE OFF 1-1b 2-2b OPEN OPEN DPST
DP P2022
P2023
ON
ON
NONE
OFF
ON
ON 1-1b 2-2b OPEN 1-1a 2-2a DPDT
POLES & CIRCUITS
1 (COM)
1b
1 (COM)
1b
1a
1 2(COM)
1b 2b
1
1b
2b
2(COM)
1a
2a
Keyway
Keyway
IMPORTANT:
VDE is marked on all models except those with
codes E & F. Switches are supplied without UL,
cULus & CSA marking unless specified.
UL, cULus & CSA recognized only when ordered
with marking on the switch.
Specific models, ratings, & ordering instructions
are noted on the General Specifications page.
Series P
Internationally Approved Toggles
A99
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable
A
Toggles
Rockers
Touch Tilt
www.nkkswitches.com
(6.35)
.250
(1.3) Dia
.051
(4.75)
.187
(9.0)
.354
Thk = (0.8)
.031
Epoxy Seal
(4.5)
.177
(2.6)
.102 (1.25)
.049
(2.0)
.079
Thk = (1.0)
.039
(7.6)
(1.17)
.046
Thk = (1.0)
(4.8)
.189
TOGGLES & BUSHINGS
E
Panel Thickness
with Keyway
.134” (3.4mm)
maximum
For 6mm Bushing: 1 Locking Ring AT507M, 1 Internal Tooth Lockwasher AT509, 2 Hex Nuts AT513M
For 12mm Bushing: 1 Hex Face Nut AT503M, 1 Locking Ring AT506M, 1 Internal Tooth Lockwasher AT508, 1 Hex Mounting Nut AT527M
Optional Splashproof Boot Assemblies (for code F): AT401 & AT4181 boots plus hex nut & o-ring; see Accessories & Hardware section.
.450”
(11.4mm)
Flatted
with 6mm
Bushing
No
Code
.689” (17.5mm)
Large Bat
with 12mm
Bushing
TERMINALS
Solder Lug
B D .748” (19.0mm)
White Capped
Column with
12mm Bushing
.512”
(13.0mm)
White Cap
with 6mm
Bushing
Panel Cutouts
Panel Thickness
with Locking Ring
.102” (2.6mm)
maximum
Panel Thickness
with Keyway
.256” (6.5mm)
maximum
Panel Thickness
with Locking Ring
.217” (5.5mm)
maximum
Standard Hardware
Z
P
No Code .187” (4.75mm)
Quick Connect
Straight PC
(12.5) Dia
.492
(11.5)
.453
(1.5)
.060
(9.0)
.354
(12.5) Dia
.492
(3.0) Dia
.118
(6.35) Di
a
.250
(5.6
)
.220
(0.6)
.024
(6.35) Di
a
.250
(6.5)
.256
(2.2) Di
a
.087
TYPICAL SWITCH DIMENSIONS
P2011 models do not have terminal 1a. P2012
P2021F, P2022F, P2023F 12mm Bushing
P2011, P2012, P2013 6mm Bushing
SPST SPDT DPST DPDT
P2021 models do not have terminals 1a & 2a. P2022F
(5.08)
.200
(10.16)
.400
(1.8) Dia Ty
p
.071
(7.62) Typ
.300
1
1a
2a
2
1b
2b
(10.16)
.400
(1.8) Dia Ty
p
.071
(7.62) Typ
.300
1
2
1b2b
(1.8) Dia Ty
p
.071
(7.62) Typ
.300
1
1b
(1.8) Dia Ty
p
.071
(7.62) Typ
.300
1
1a
1b
25°
(13.0)
.512
(4.2) Dia
.165
25°
(11.4)
.450
(2.54)
.100
(17.5)
.689
25°
(6.0) Dia
.236
(19.0)
.748
25°
(4.4) Dia
.173
1b
1a
1
(20.5)
.807
(2.6)
.102
Keyway
(11.0)
.433
(13.0)
.512
(8.0)
.315
(7.62)
.300
M6 P0.75
(0.5)
.020
(0.8)
.031
(5.0)
.197
25°
(4.2) Dia
.165
(22.0)
.866
(1.0) Typ
.039
(1.25) x (2.0) Typ
.049 x .079
(0.9)
.035
1
2
2a 1a
1b2b
(10.16)
.400
(20.5)
.807
(2.6) Typ
.102
Keyway
(20.0)
.787
M12 P1
(7.62)
.300
(0.5)
.020
(0.8)
.031
(5.0)
.197
25°
(6.0) Dia
.236
(17.5)
.689
(12.0)
.472
(21.1)
.831
(1.0) Typ
.039
(1.25) x (2.0) Typ
.049 x .079
(18.0)
.709
25°
(8.0) Dia
.315
.689” (17.5mm)
Large Bat &
AT406B Cap with
12mm Bushing
F