A Electrical Capacity Resistive Load: Motor Load: Lamp Load: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Angle of Throw: Materials & Finishes Toggle Cap: Lever: Bushing: Frame: Case/Base: Movable Contacts: Stationary Contacts: Terminals: Rotaries Environmental Data Operating Temp Range: Humidity: Vibration: Tactiles Slides Internationally Approved Toggles General Specifications Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series P Shock: Installation Tilt Soldering Time & Temp: Standards & Certifications Flammability Standards: UL: 10 milliohms maximum 1,000 megohms minimum @ 500V DC 2,000V AC minimum between contacts for 1 minute minimum; 4,000V AC minimum between contacts & case for 1 minute minimum 100,000 operations minimum 25,000 operations minimum 25 Polypropylene for No Code, Code D; Polyvinyl chloride for Code B (see Ordering Example) Brass with chrome plating Brass with nickel plating Stainless steel Diallyl phthalate resin (UL94V-0) Silver alloy with silver plating Pure silver with silver plating Copper with silver plating -10C through +85C (+14F through +185F) 90 ~ 95% humidity for 96 hours @ 40C (104F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering Recommended (Straight PC): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 rated case/base File No. E44145 - Recognized only when ordered with marking on switch. Add "/U" or "/CUL" to end of part number to order UL recognized switch. Models with No Code, E, F & D are recognized at 10A @ 125V AC & 6A @ 250V AC. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add "/C" to end of part number to order CSA certified switch. Models with No Code, E, F and D are certified at 10A @ 125V AC & 6A @ 250V AC. VDE: License No. 119174 Models with No Code, B & D are approved at 10A @ 125V AC & 6A @ 250V AC. Models with No Code, B & D meet EN 61058-1 standard. Supplement Accessories Indicators Touch Cleaning: 10A @ 125V AC or 6A @ 250V AC 400W @ 125V AC 2A @ 125V AC for On-Off-On circuit & 3A @ 125V AC for other circuits A96 www.nkkswitches.com 8/11/17 A Rockers Distinctive Characteristics Toggles Series P Internationally Approved Toggles Pushbuttons Meets EN 61058-1 standard. Programmable Illuminated PB High torque bushing construction prevents rotation or separation from frame during installation. Stainless steel frame resists corrosion and increases environmental safety. Case/base of heat resistant resin meets UL94V-0 flammability standard. Keylocks Contacts of special silver alloy resist arcing and guarantee stable electrical contact and long life. Slides Rotaries High insulating barriers increase isolation of circuits in double pole devices and provide added protection to contact points. Tactiles Prominent external insulating barriers increase insulation resistance and dielectric strength. Actual Size Supplement Accessories Indicators Touch Clinching of the frame to the case well above the base and terminals provides 4,000V dielectric strength. Tilt Epoxy sealed terminals prevent entry of flux, solvents, and other contaminants. www.nkkswitches.com A97 TYPICAL SWITCH ORDERING EXAMPLE P20 Pushbuttons 22 Poles & Circuits B Toggles & Bushings 11 SPST ON NONE OFF 12 SPDT ON NONE ON 13 SPDT ON OFF ON 21 DPST ON NONE OFF 22 DPDT ON NONE ON 23 DPDT ON OFF ON Keylocks Programmable Illuminated PB Internationally Approved Toggles A Rockers Toggles Series P No Code Terminals .512" (13.0mm) White Cap with 6mm Bushing E .450" (11.4mm) Flatted with 6mm Bushing B .689" (17.5mm) Large Bat & AT406B Cap with 12mm Bushing F .689" (17.5mm) Large Bat with 12mm Bushing D .748" (19.0mm) White Capped Column with 12mm Bushing No Code Solder Lug P Straight PC Z .187" (4.75mm) Quick Connect DESCRIPTION FOR TYPICAL ORDERING EXAMPLE P2022F Rotaries IMPORTANT: VDE is marked on all models except those with codes E & F. Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. .689" (17.5mm) Large Bat with 12mm Bushing Slides DPDT ON-NONE-ON Circuit Tactiles Solder Lug Terminals POLES & CIRCUITS Tilt Toggle Position Down Model SP P2011 Up Keyway Down Center Throw & Schematics Up Note: Terminal numbers are on the switch. Keyway Supplement Accessories Indicators Touch Pole Center Connected Terminals ON NONE OFF 1-1b OPEN OPEN 1 (COM) SPST 1b 1 (COM) SP P2012 P2013 ON ON NONE OFF ON ON 1-1b OPEN 1-1a SPDT DP P2021 ON NONE OFF 1-1b 2-2b OPEN OPEN DPST DP P2022 P2023 ON ON NONE OFF ON ON 1-1b 2-2b OPEN 1-1a 2-2a DPDT A98 1a 1 (COM) 2 1b 1 1a www.nkkswitches.com 1b 2b (COM) 1b 2a 2 2b (13.0) .512 F 25 (8.0) Dia .315 25 .689" (17.5mm) Large Bat with 12mm Bushing (5.08) .200 (18.0) .709 (11.4) .450 25 (6.0) Dia .236 Panel Thickness with Locking Ring .102" (2.6mm) maximum (5.6) .220 (19.0) .748 (6.35) Dia .250 (0.6) .024 (6.5) .256 (6.35) Dia .250 (12.5) Dia .492 Panel Thickness with Keyway .256" (6.5mm) maximum (2.2) Dia .087 25 (4.4) Dia .173 (17.5) .689 Panel Cutouts Panel Thickness with Keyway .134" (3.4mm) maximum .748" (19.0mm) White Capped Column with 12mm Bushing D Pushbuttons (2.54) .100 .689" (17.5mm) Large Bat & AT406B Cap with 12mm Bushing B Panel Thickness with Locking Ring .217" (5.5mm) maximum (11.5) .453 (1.5) .060 (12.5) Dia .492 (9.0) .354 (3.0) Dia .118 Standard Hardware For 6mm Bushing: 1 Locking Ring AT507M, 1 Internal Tooth Lockwasher AT509, 2 Hex Nuts AT513M For 12mm Bushing: 1 Hex Face Nut AT503M, 1 Locking Ring AT506M, 1 Internal Tooth Lockwasher AT508, 1 Hex Mounting Nut AT527M Optional Splashproof Boot Assemblies (for code F): AT401 & AT4181 boots plus hex nut & o-ring; see Accessories & Hardware section. No Code Epoxy Seal Straight PC (4.8) .189 Epoxy Seal SPST 1 (1.17) .046 Thk = (1.0) .039 2b 1b (7.62) Typ .300 SPDT (1.8) Dia Typ .071 (7.62) Typ .300 1 DPST (7.62) Typ .300 1 DPDT (1.8) Dia Typ .071 (10.16) .400 (1.8) Dia Typ .071 (4.75) .187 Thk = (0.8) .031 1b 2 1a (9.0) .354 (6.35) .250 (1.3) Dia .051 1b (7.6) .299 .187" (4.75mm) Quick Connect Z (2.0) (4.5) .079 (2.6) .177 .102 (1.25) .049 Thk = (1.0) .039 2b 1b 2 1 2a (7.62) Typ .300 1a (10.16) .400 (1.8) Dia Typ .071 TYPICAL SWITCH DIMENSIONS 6mm Bushing P2011, P2012, P2013 M6 P0.75 (1.0) Typ .039 Tilt Keyway (1.25) x (2.0) Typ .049 x .079 1b (0.8) .031 (7.62) .300 (11.0) .433 (13.0) .512 (5.0) .197 (22.0) .866 Touch (0.9) .035 (8.0) .315 1a (0.5) .020 (2.6) .102 P2012 P2011 models do not have terminal 1a. 12mm Bushing P2021F, P2022F, P2023F Keyway (1.25) x (2.0) Typ .049 x .079 M12 P1 (1.0) Typ .039 2b (0.8) .031 (7.62) .300 25 (6.0) Dia .236 (20.0) .787 (17.5) .689 (12.0) .472 (21.1) .831 (5.0) .197 1b 2 1 2a (0.5) .020 (20.5) .807 1a (10.16) .400 (2.6) Typ .102 P2021 models do not have terminals 1a & 2a. www.nkkswitches.com Indicators (4.2) Dia .165 (20.5) .807 1 Accessories 25 Supplement P Solder Lug Rotaries TERMINALS Programmable Illuminated PB 25 (4.2) Dia .165 .450" (11.4mm) Flatted with 6mm Bushing Keylocks E Slides .512" (13.0mm) White Cap with 6mm Bushing Tactiles No Code Rockers A TOGGLES & BUSHINGS Toggles Series P Internationally Approved Toggles P2022F A99