POWER LGA C Series 15 - 100 Watts Data Sheet Total Power: 15 - 100 W # of Outputs: Single SPECIAL FEATURES 3, 6, 10 and 20 A output current rating Wide input voltage range; up to 14 V Adjustable output voltage; 0.59-5.1 V Excellent transient response High efficiency Output margining Power enable Minimal airflow requirement Termination voltage capability Ultra compact profile and footprint RoHS compliant Remote sense Termination voltage capability SAFETY Designed to meet EN60950 International Standards for Solderability: J-STD-002B IEC-60068-2-58 Electrical Specifications Output 3/6/10 A Models Output voltage See Page 3 Output setpoint accuracy 0.1% trim resistors 20 A Model 0.59 - 5.1 V 1.0% Line regulation 0.2% Load regulation 0.5% Max Current Max Power 15/30/50 W 100 W Overshoot At turn-on 0% Undershoot At turn-off 0 mV Ripple and noise 5 Hz to 20 MHz See Note 1 Vin = 5 V, Vout = 2.5 V Transient response See Notes 1 and 2 Vin = 5 V, Vout = 2.5 V 20/25/30 mV 30 mV 100/160/160 mV 15 s recovery to within regulation band 1175 mV 15 s recovery to within regulation band 3 - 14 Vdc 4.5 - 14 Vdc Input Input voltage range3 Input current Enable On at (0 A) Enable Off Start-up time Power up Enable On/Off 50 mA 5 mA 3 ms 2 ms General Efficiency Vin = 5 Vout, Vo = 2.5 V, Iout = 50% Imax Switching frequency Material flammability MTBF 92% typ. 1 MHz 800 kHz UL94V-0 12 V @ 40 C 100% load Bellcore 332 Coplanarity Thermal performance See Technical Reference Note 92% typ. > 20,000,000 hours 150 m Operating ambient Non-operating ambient -40 C to +85 C -40 C to +125 C LGA C Series Data Sheet Electrical Specifications Protection Short circuit Hiccup, non-latching Overvoltage Hiccup, non-latching Mininum Recommended System Capacitance 3/6/10 A Model 20 A Model 1 F 10 F Short circuit Operating Information Standard Model Numbers Output Current Regulation Output Power (Max.) Input Voltage Output Voltage Min Max Efficiency (Typical) Min Max LGA03C-00SADJJ 15 W 3 - 14.0 Vdc 0.59 - 5.1 Vdc 0A 3A 92% 0.2% 0.5% LGA06C-00SADJJ 30 W 3 - 14.0 Vdc 0.59 - 5.1 Vdc 0A 6A 92% 0.2% 0.5% LGA10C-00SADJJ 50 W 3 - 14.0 Vdc 0.59 - 5.1 Vdc 0A 10 A 92% 0.2% 0.5% LGA20C-01SADJJ 100 W 4.5 - 14.0 Vdc 0.59 - 5.1 Vdc 0A 20 A 91% 0.2% 0.5% Model Number System with Options Rated Output Current Product Family LGA Performance XX C Rated Output Current 03 = 3 Amp 06 = 6 Amp 10 = 10 Amp 20 = 20 Amp Performance C = Cost Optimized Input Voltage - 00 Input Voltage 00 = 3 - 14.0 V 01 = 4.5 - 14.0 V Heatsink Number System with Options Product Family LGA Land Grid Array Product - HTSK Heatsink Purpose - KIT Heatsink and Adhesive * Height is the total height of the LGA20C-00SADJJ with heatsink attached. Height* - XXX Total Height (LGA20 + Heatsink) 045 = 0.45" 048 = 0.48" 050 = 0.50" Type of Output SADJ Type of Output Single Adjustable Output Options X Options X = Various Options (see Sales Rep) RoHS Compliance J RoHS Compliance J = Pb free (RoHS 6/6 compliant) LGA C Series Data Sheet Application Equations Setting Output Voltage Setting Margin Control Default output voltage: 0.591 V To margin the output up, pull the margin control pin high. To margin down, pull the margin control pin low. If the pin is left floating, the feature is disabled. The maximum margining range is 33% of the oputput default voltage setting, with maximum output at 5.5 V The outut voltage may be adjusted with a resistor placed between the "Trim" and "-Sense" pin. The formula for calcuating the value of this resistor is: Vmargin_up = 0.1182 * Rtrim (k) = 1.182 Vout - 0.591 Rmargin Rtrim + 2k * Rofs+ Rtrim Vmargin_down = 0.1182 * See Technical Reference Note for other trimming methods. Rmargin Rtrim + 2k * RofsRtrim Setting Under Voltage Lock Out - 3, 6, 10 A Models Setting Under Voltage Lock Out - 20 A Models Default Turn-on voltage: 2.9 V (300 mV Hysteresis) Default Turn-on voltage: 4.3 V (300 mV Hysteresis) The Turn-on voltage may be adjusted with a resistor placed between the "Enable" and "Ground" pins. The Turn-on voltage may be adjusted with a resistor placed between the "Enable" and "Ground" pins. The formula for calculating the value of this resistor is: The formula for calculating the value of this resistor is: Ruvlo (k) = 14.81 * 6.81 (6.81 * VTurn_on) - 18.16 Ruvlo (k) = 30.1 * 4.22 (8.577 * VTurn_on) - 34.32 *ONLY USE WITH OPEN COLLECTOR DEVICE *DO NOT DRIVE PIN WITH A VOLTAGE *ONLY USE WITH OPEN COLLECTOR DEVICE *DO NOT DRIVE PIN WITH A VOLTAGE Notes: 1. Measured as per recommended minimum system capacitance. 2. di/dt = 10 A/ s,12 Vin = Norm, Tc = 25 C, load change = 50% lo 100% Imax. 3. Internal input capacitance is rated 16 Vdc maximum. Rofs+ Rofs- Rmargin Margin Control Enable On/Off 12 23 LGA C Series 9-10 5-8 Cin 22 Power Good Vout 1-4 Ruvlo Vin 13 21 15 14 24 +Sense Cout R L O A D Rtrim -Sense GND GND External input fusing is recommended. 8 7 6 5 4 8 7 6 5 4 LGA C Series Data Sheet 1 2 3 REVISION RECORD D PART NUMBER REV 3 7091323-0000 A 7091323-0000 PART NUMBER B REV DESCRIPTION 2 DRAFT DATE 1 RELE ASE FORRECORD PRODUCTION REVISION MATT KRETMAN 04/10/09 UPDATE TO PARALLELISM SPEC DESCRIPTION MATT KRETMAN DRAFT 05/26/09 DATE 7091323-0000 A RELE ASE FOR PRODUCTION MATT KRETMAN 04/10/09 7091323-0000 B UPDATE TO PARALLELISM SPEC MATT KRETMAN 05/26/09 D D D Mechanical Drawing and Footprint .139 3.53 MAX A C SECTION A-A SCALE 4 : 1 A .139 3.53 MAX A A C A .650 16.51 MAX C .020.003 0.510.08 .031 0.79 PCB REF .102 2.59 REF Component Height .031 0.79 PCB REF .102 2.59 REF A .650 16.51 MAX B .020.003 0.510.08 SECTION A-A SCALE 4 : 1 A .01 A B Model # DIM A in (mm) LGA03 LGA06 LGA10 0.129 (3.27) B B 0.210 (5.33) LGA20 .01 A .650 16.51 MAX C .650 16.51 MAX NOTE: 1. 9300161-0000 PACKAGING AND MATERIAL HANDLING PROCEDURE. 2. COSMETIC AND WORKMANSHIP PER 9300152-0000. 3. LABEL SHOWN FOR PLACEMENT REFERENCE ONLY. NOTE: UNLESS OTHERWISE SPECIFIED 1. 9300161-0000 PACKAGING AND MATERIAL HANDLING PROCEDURE. EMERSON NETWORK POWER DIMENSIONS ARE IN INCHES EDEN PRAIRIE, MN 55433 2. COSMETIC AND WORKMANSHIP PER 9300152-0000. PH. 952-941-1100 TOLERANCES: 3. LABEL SHOWN PLACEMENT REFERENCE ONLY. 2 PLACE 3 PLACE FOR ANGLES MATERIAL A - .03 Recommended System Board Footprint A FINISH- - 0.220 (5.59) 0.269 (6.83) 0.318 (8.08) 0.367 (9.32) 0.416 (10.57) 0.465 (11.81) 0.514 (13.06) 0.563 (14.30) 0.612 (15.54) 2X .120 X .110 0 (0) 8 8 DETACHED LIST 7 6 5 4 7 6 5 4 PIN 16 3 14X .025 X .025 PIN 24 PIN 15 0.612 (15.55) 0.567 (14.40) 0.522 (13.26) 0.477 (12.12) 0.432 (10.97) 0.387 (9.83) PIN 11 PIN 8 0.570 (14.48) PIN 10 PIN 9 0.295 (7.50) PIN 5 PIN 1 0.125 (3.18) 0.690 (17.53) 0.564 (14.33) 0.418 (10.62) 0.272 (6.91) 0 (0) 0.126 (3.20) 8X .120 X .120 B 2 Vout 3 Vout 4 Vout 5 GND 6 GND SHEET 1 OF 5 CAD FILE: 1 NC 12 - Offset 13 + Offset 14 - Sense 15 + Sense 16 NC 17 NC 18 NC 19 NC 20 NC 21 Enable 22 Power Good 23 Margin Control 23 Trim 0.048 (1.22) B LGA10C-00SADJJ Vout Vin 0.180 (4.57) 0.225 (5.72) SHEETREV. 1 OF 5 PROJECT USED ON: SIZE SCALE: X = X 2 11 0.114 (2.90) 0.194 (4.93) 10APR09 THIRD ANGLE PROJECTION CAD FILE: 7091323-00001 10 0.487 (12.37) 0.340 (8.64) ENGINEER 1 10APR09 Vin 0.317 (8.05) 0.114 (2.90) Single Output 2 B LGA10C-00SADJJ GND 0.000 (0) 0.147 (3.73) 0.098 (2.49) 0.049 (1.24) 0.294 (7.47) 0.245 (6.22) 0.196 (4.98) 0.392 (9.96) 0.343 (8.71) 0.487 (12.37) 0.114" X 0.114" 8X 0.114" X 0.104" 0.024 (0.61) 2X EMERSON NETWORK POWER EDEN PRAIRIE, MN 55433 REV. PH. 952-941-1100 PROJECT USED ON: B 9 0.045 (1.14) 0.090 (2.29) 0.135 (3.43) 0.114 (2.90) DWG. NO. TITLE: SIZE DWG. SCALE:NO.X = X KEEP OUT AREA 0 (0) 0.177 (4.50) DATE GND 0.024" X.024" 13X 0.024 (0.61) .005 10APR09 8 Recommended Solder Paste Stencil 0.042 (1.07) HOLE TOLERANCE: MATT KRETMAN APPROVALS THIRD ANGLE DRAWN PROJECTION MATT KRETMAN A A 7 Tolerance Note: 0.010 (0.25) 0.104 (2.64) - LGA 10 TLA 0 (0) PIN 4 0 (0) MODULE OUTLINE 3 TITLE: 7091323-0000 Pin Assignments LGA 10 TLA MATT KRETMAN DETACHED LIST 0.690 (17.53) 0.435 (11.05) FINISH 1 .015 HOLE TOLERANCE: .005 UNLESS OTHERWISE SPECIFIED DATE APPROVALS DIMENSIONS ARE IN INCHES DRAWN TOLERANCES: 10APR09 MATT KRETMAN 2 PLACE 3 PLACE ANGLES 1 .015 .03 ENGINEER MATERIAL WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. (c) 2015 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com LGA3-20C DS Rev. 02-02-2015 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Artesyn Embedded Technologies: LGA-HTSK-KIT-048 LGA-HTSK-KIT-050 LGA-HTSK-KIT-045 LGA10C-EVAL-KIT