LM4666, LM4666SDBD www.ti.com SNAS189A - MAY 2004 - REVISED MAY 2013 LM4666 Filterless High Efficiency Stereo 1.2W Switching Audio Amplifier Check for Samples: LM4666, LM4666SDBD FEATURES DESCRIPTION * The LM4666 is a fully integrated single-supply high efficiency switching audio amplifier. It features an innovative modulator that eliminates the LC output filter used with typical switching amplifiers. Eliminating the output filter reduces parts count, simplifies circuit design, and reduces board area. The LM4666 processes analog inputs with a delta-sigma modulation technique that lowers output noise and THD when compared to conventional pulse width modulators. 1 2 * * * * * * * No Output Filter Required for Inductive Transducers Selectable Gain of 6dB or 12dB Very Fast Turn On Time: 6ms (typ) Minimum External Components "Click and Pop" Suppression Circuitry Micro-Power Shutdown Mode Short Circuit Protection Available in Space-Saving NHK0014A Package APPLICATIONS * * * Mobile Phones PDAs Portable Electronic Devices KEY SPECIFICATIONS * * * * * * Efficiency at 3V, 100mW into 8 Transducer: 79% (typ) Efficiency at 3V, 450mW into 8 Transducer: 84% (typ) Efficiency at 5V, 1W into 8 Transducer: 85% (typ) Total Quiescent Power Supply Current: 7.0mA (typ) Total Shutdown Power Supply Current: 0.02A (typ) Single supply range: 2.8V to 5.5V The LM4666 is designed to meet the demands of mobile phones and other portable communication devices. Operating on a single 3V supply, it is capable of driving 8 transducer loads at a continuous average output of 450mW with less than 1%THD+N. Its flexible power supply requirements allow operation from 2.8V to 5.5V. The LM4666 has high efficiency with an 8 transducer load compared to a typical Class AB amplifier. With a 3V supply, the IC's efficiency for a 100mW power level is 79%, reaching 84% at 450mW output power. The LM4666 features a low-power consumption shutdown mode. Shutdown may be enabled by driving the Shutdown pin to a logic low (GND). The LM4666 has fixed selectable gain of either 6dB or 12dB. The LM4666 has short circuit protection against a short from the outputs to VDD or GND. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004-2013, Texas Instruments Incorporated LM4666, LM4666SDBD SNAS189A - MAY 2004 - REVISED MAY 2013 www.ti.com Typical Application Figure 1. Typical Audio Amplifier Application Circuit Connection Diagram Top View Figure 2. WSON Package See Package Number NHK0014A 2 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD LM4666, LM4666SDBD www.ti.com SNAS189A - MAY 2004 - REVISED MAY 2013 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) (3) Supply Voltage (1) 6.0V -65C to +150C Storage Temperature VDD + 0.3V V GND - 0.3V Voltage at Any Input Pin Power Dissipation (4) Internally Limited ESD Susceptibility, pins 4, 7, 11, 14 (5) 1kV ESD Susceptibility, all other pins (5) 2.0kV ESD Susceptibility (6) 200V Junction Temperature (TJ) Thermal Resistance 150C JA (NHK0014A) 63C/W JC (NHK0014A) 12C/W Soldering Information: See AN-1112 (SNVA009) "microSMD Wafers Level Chip Scale Package." (1) (2) (3) (4) (5) (6) All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX-TA)/JA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4666, TJMAX = 150C. The typical JA is 63C/W and the typical JC is 12C/W for the NHK0014A package. Human body model, 100pF discharged through a 1.5k resistor. Machine Model, 220pF - 240pF discharged through all pins. Operating Ratings (1) (2) TMIN TA TMAX Temperature Range (1) (2) -40C TA 85C 2.8V VDD 5.5V Supply Voltage All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication of device performance. Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD Submit Documentation Feedback 3 LM4666, LM4666SDBD SNAS189A - MAY 2004 - REVISED MAY 2013 www.ti.com Electrical Characteristics VDD = 5V (1) (2) The following specifications apply for VDD = 5V and RL = 15H + 8 + 15H unless otherwise specified. Limits apply for TA = 25C. Parameter LM4666 Test Conditions IDD Quiescent Power Supply Current VIN = 0V, No Load VIN = 0V, RL = 15H + 8 + 15H ISD Shutdown Current VSD = GND (6) VSDIH Shutdown Voltage Input High VSDIL VGSIH Typ (3) Limit (4) (5) Units (Limits) 15 16 mA mA 0.02 A 1.2 V Shutdown Voltage Input Low 1.1 V Gain Select Input High 1.2 V VGSIL Gain Select Input Low 1.1 V AV Closed Loop Gain VGain Select = VDD 6 dB AV Closed Loop Gain VGain Select = GND 12 dB VOS Output Offset Voltage 10 mV TWU Wake-up Time 6 ms 1.2 W % Po Output Power THD = 1% (max), f = 1kHz, 22kHz BW THD+N Total Harmonic Distortion+Noise PO = 100mWRMS/Channel, fIN = 1kHz, 22kHz BW, Both channels in phase 0.65 XTALK Channel Separation PO = 100mWRMS, f = 1kHz 57 dB VGain Select = VDD 90 k VGain Select = GND 60 k VRipple = 100mVRMS sine wave, fRIPPLE = 217Hz Inputs terminated to AC GND 60 dB VRipple = 100mVRMS sine wave, fRIPPLE = 217Hz POUT = 10mW,1kHz 65 dB RIN Differential Input Resistance PSRR Power Supply Rejection Ratio CMRR Common Mode Rejection Ratio VRipple = 100mVRMS, fRipple = 217Hz, Input referred 48 dB SNR Signal to Noise Ratio PO = 1WRMS; A-Weighted Filter 83 dB OUT Output Noise A-Weighted filter, Vin = 0V 200 V (1) (2) (3) (4) (5) (6) 4 All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication of device performance. Typical specifications are specified at 25C and represent the parametric norm. Tested limits are specified to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. Shutdown current is measured in a normal room environment. Exposure to direct sunlight will increase ISD by a maximum of 2A. The Shutdown pin should be driven as close as possible to GND for minimal shutdown current and to VDD for the best THD performance in PLAY mode. See the Application Information section under SHUTDOWN FUNCTION for more information. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD LM4666, LM4666SDBD www.ti.com SNAS189A - MAY 2004 - REVISED MAY 2013 Electrical Characteristics VDD = 3V (1) (2) The following specifications apply for VDD = 3V and RL = 15H + 8 + 15H unless otherwise specified. Limits apply for TA = 25C. Parameter IDD Test Conditions Quiescent Power Supply Current VIN = 0V, No Load VIN = 0V, RL = 15H + 8 + 15H VSD = GND (6) LM4666 Limit (4) (5) Units (Limits) 6.5 7.0 10 mA (max) Typ (3) ISD Shutdown Current 0.02 2.0 A (max) VSDIH Shutdown Voltage Input High 1.0 1.4 V (min) VSDIL Shutdown Voltage Input Low 0.8 0.4 V (max) VGSIH Gain Select Input High 1.0 1.4 V (min) VGSIL Gain Select Input Low 0.8 0.4 V (max) AV Closed Loop Gain VGain Select = VDD 6 5.25 6.75 dB (min) dB (max) AV Closed Loop Gain VGain Select = GND 12 11.25 12.75 dB (min) dB (max) VOS Output Offset Voltage 10 35 mV (max) TWU Wake-up Time 6 ms Po Output Power THD = 1% (max); f = 1kHz, 22kHz BW THD+N Total Harmonic Distortion+Noise PO = 100mWRMS/Channel, fIN = 1kHz, 22kHz BW, Both channels in phase 0.65 XTALK Channel Separation PO = 100mWRMS, f = 1kHz 57 dB VGain Select = VDD 90 k VGain Select = GND 60 k Vripple = 100mVRMS sine wave, fRIPPLE = 217Hz, Inputs terminated to AC GND 60 dB VRipple = 100mVRMS sine wave, fRIPPLE = 217Hz, POUT = 10mW,1kHz 65 dB 48 dB RIN Differential Input Resistance PSRR Power Supply Rejection Ratio 450 400 mW (min) % CMRR Common Mode Rejection Ratio VRipple = 100mVRMS, fRipple = 217Hz, Input referred SNR Signal to Noise Ratio PO = 400mWRMS, A-Weighted Filter 83 dB OUT Output Noise A-Weighted filter, Vin = 0V 125 V (1) (2) (3) (4) (5) (6) All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication of device performance. Typical specifications are specified at 25C and represent the parametric norm. Tested limits are specified to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. Shutdown current is measured in a normal room environment. Exposure to direct sunlight will increase ISD by a maximum of 2A. The Shutdown pin should be driven as close as possible to GND for minimal shutdown current and to VDD for the best THD performance in PLAY mode. See the Application Information section under SHUTDOWN FUNCTION for more information. External Components Description (Figure 1) Components Functional Description 1. CS Supply bypass capacitor which provides power supply filtering. Refer to the POWER SUPPLY BYPASSING section for information concerning proper placement and selection of the supply bypass capacitor. 2. CI Input AC coupling capacitor which blocks the DC voltage at the amplifier's input terminals. Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD Submit Documentation Feedback 5 LM4666, LM4666SDBD SNAS189A - MAY 2004 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (1) (1) 6 THD+N vs Frequency VDD = 5V, RL = 15H + 8 + 15H POUT = 100mW/Channel, 30kHz BW THD+N vs Frequency VDD = 3V, RL = 15H + 8 + 15H POUT = 100mW/Channel, 30kHz BW Figure 3. Figure 4. THD+N vs Frequency VDD = 3V, RL = 15H + 4 + 15H POUT = 100mW/Channel, 30kHz BW THD+N vs Output Power/Channel VDD = 5V, RL = 15H + 8 + 15H f = 1kHz, 22kHz BW Figure 5. Figure 6. THD+N vs Output Power/Channel VDD = 3V, RL = 15H + 4 + 15H f = 1kHz, 22kHz BW THD+N vs Output Power/Channel VDD = 3V, RL = 15H + 8 + 15H f = 1kHz, 22kHz BW Figure 7. Figure 8. The performance graphs were taken using the Audio Precision AUX-0025 Switching Amplifier Measurement Filter in series with the LC filter on the demo board. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD LM4666, LM4666SDBD www.ti.com SNAS189A - MAY 2004 - REVISED MAY 2013 Typical Performance Characteristics(1) (continued) CMRR vs Frequency VDD = 5V, RL = 15H + 8 + 15H VCM = 100mVRMS Sine Wave, 30kHz BW CMRR vs Frequency VDD = 3V, RL = 15H + 8 + 15H VCM = 100mVRMS Sine Wave, 30kHz BW Figure 9. Figure 10. PSRR vs Frequency VDD = 5V, RL = 15H + 8 + 15H VRipple = 100mVRMS Sine Wave, 22kHz BW PSRR vs Frequency VDD = 3V, RL = 15H + 8 + 15H VRipple = 100mVRMS Sine Wave, 22kHz BW Figure 11. Figure 12. Efficiency and Power Dissipation vs Output Power VDD = 5V, RL = 15H + 8 + 15H, f = 1kHz, THD 1% Efficiency and Power Dissipation vs Output Power VDD = 3V, RL = 15H + 8 + 15H, f = 1kHz, THD 1% Figure 13. Figure 14. Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD Submit Documentation Feedback 7 LM4666, LM4666SDBD SNAS189A - MAY 2004 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics(1) (continued) 8 Efficiency and Power Dissipation vs Output Power VDD = 3V, RL = 15H + 4 + 15H, f = 1kHz, THD 1% Gain Select Threshold VDD = 3V Figure 15. Figure 16. Gain Select Threshold VDD = 5V Gain Select Threshold vs Supply Voltage RL = 15H + 8 + 15H Figure 17. Figure 18. Output Power/Channel vs Supply Voltage RL = 15H + 8 + 15H, f = 1kHz 22kHz BW Output Power/Channel vs Supply Voltage RL = 15H + 4 + 15H, f = 1kHz 22kHz BW Figure 19. Figure 20. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD LM4666, LM4666SDBD www.ti.com SNAS189A - MAY 2004 - REVISED MAY 2013 Typical Performance Characteristics(1) (continued) Shutdown Threshold VDD = 5V Shutdown Threshold VDD = 3V Figure 21. Figure 22. Shutdown Threshold vs Supply Voltage RL = 15H + 8 + 15H Figure 23. Supply Current vs Shutdown Voltage RL = 15H + 8 + 15H Supply Current vs Supply Voltage RL = 15H + 8 + 15H Figure 24. Figure 25. Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD Submit Documentation Feedback 9 LM4666, LM4666SDBD SNAS189A - MAY 2004 - REVISED MAY 2013 www.ti.com APPLICATION INFORMATION GENERAL AMPLIFIER FUNCTION The output signals generated by the LM4666 consist of two, BTL connected, output signals that pulse momentarily from near ground potential to VDD on each channel. The two outputs on a given channel can pulse independently with the exception that they both may never pulse simultaneously as this would result in zero volts across the BTL connected load. The minimum width of each pulse is approximately 160ns. However, pulses on the same output can occur sequentially, in which case they are concatenated and appear as a single wider pulse to achieve an effective 100% duty cycle. This results in maximum audio output power for a given supply voltage and load impedance. The LM4666 can achieve much higher efficiencies than class AB amplifiers while maintaining acceptable THD performance. The short (160ns) drive pulses emitted at the LM4666 outputs means that good efficiency can be obtained with minimal load inductance. The typical transducer load on an audio amplifier is quite reactive (inductive). For this reason, the load can act as it's own filter, so to speak. This "filter-less" switching amplifier/transducer load combination is much more attractive economically due to savings in board space and external component cost by eliminating the need for a filter. POWER DISSIPATION AND EFFICIENCY In general terms, efficiency is considered to be the ratio of useful work output divided by the total energy required to produce it with the difference being the power dissipated, typically, in the IC. The key here is "useful" work. For audio systems, the energy delivered in the audible bands is considered useful including the distortion products of the input signal. Sub-sonic (DC) and super-sonic components (>22kHz) are not useful. The difference between the power flowing from the power supply and the audio band power being transduced is dissipated in the LM4666 and in the transducer load. The amount of power dissipation in the LM4666 is very low. This is because the ON resistance of the switches used to form the output waveforms is typically less than 0.25. This leaves only the transducer load as a potential "sink" for the small excess of input power over audio band output power. The LM4666 dissipates only a fraction of the excess power requiring no additional PCB area or copper plane to act as a heat sink. DIFFERENTIAL AMPLIFIER EXPLANATION As logic supply voltages continue to shrink, designers are increasingly turning to differential analog signal handling to preserve signal to noise ratios with restricted voltage swing. The LM4666 is a fully differential amplifier that features differential input and output stages. A differential amplifier amplifies the difference between the two input signals. Traditional audio power amplifiers have typically offered only single-ended inputs resulting in a 6dB reduction in signal to noise ratio relative to differential inputs. The LM4666 also offers the possibility of DC input coupling which eliminates the two external AC coupling, DC blocking capacitors. The LM4666 can be used, however, as a single ended input amplifier while still retaining it's fully differential benefits. In fact, completely unrelated signals may be placed on the input pins. The LM4666 simply amplifies the difference between the signals. A major benefit of a differential amplifier is the improved common mode rejection ratio (CMRR) over single input amplifiers. The common-mode rejection characteristic of the differential amplifier reduces sensitivity to ground offset related noise injection, especially important in high noise applications. PCB LAYOUT CONSIDERATIONS As output power increases, interconnect resistance (PCB traces and wires) between the amplifier, load and power supply create a voltage drop. The voltage loss on the traces between the LM4666 and the load results is lower output power and decreased efficiency. Higher trace resistance between the supply and the LM4666 has the same effect as a poorly regulated supply, increase ripple on the supply line also reducing the peak output power. The effects of residual trace resistance increases as output current increases due to higher output power, decreased load impedance or both. To maintain the highest output voltage swing and corresponding peak output power, the PCB traces that connect the output pins to the load and the supply pins to the power supply should be as wide as possible to minimize trace resistance. 10 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD LM4666, LM4666SDBD www.ti.com SNAS189A - MAY 2004 - REVISED MAY 2013 The rising and falling edges are necessarily short in relation to the minimum pulse width (160ns), having approximately 2ns rise and fall times, typical, depending on parasitic output capacitance. The inductive nature of the transducer load can also result in overshoot on one or both edges, clamped by the parasitic diodes to GND and VDD in each case. From an EMI standpoint, this is an aggressive waveform that can radiate or conduct to other components in the system and cause interference. It is essential to keep the power and output traces short and well shielded if possible. Use of ground planes, beads, and micro-strip layout techniques are all useful in preventing unwanted interference. As the distance from the LM4666 and the speakers increase the amount of EMI radiation will increase since the output wires or traces acting as antenna become more efficient with length. What is acceptable EMI is highly application specific. Ferrite chip inductors placed close to the LM4666 may be needed to reduce EMI radiation. The value of the ferrite chip is very application specific. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection ratio (PSRR). The capacitor (CS) location should be as close as possible to the LM4666. Typical applications employ a voltage regulator with a 10F and a 0.1F bypass capacitors that increase supply stability. These capacitors do not eliminate the need for bypassing on the supply pin of the LM4666. A 1F tantalum capacitor is recommended. SHUTDOWN FUNCTION In order to reduce power consumption while not in use, the LM4666 contains shutdown circuitry that reduces current draw to less than 0.01A. The trigger point for shutdown is shown as a typical value in the Electrical Characteristics Tables and in the Shutdown Hysteresis Voltage graphs found in the Typical Performance Characteristics section. It is best to switch between ground and supply for minimum current usage while in the shutdown state. While the LM4666 may be disabled with shutdown voltages in between ground and supply, the idle current will be greater than the typical value. Increased THD may also be observed with voltages less than VDD on the Shutdown pin when in PLAY mode. The LM4666 has an internal resistor connected between GND and Shutdown pins. The purpose of this resistor is to eliminate any unwanted state changes when the Shutdown pin is floating. The LM4666 will enter the shutdown state when the Shutdown pin is left floating or if not floating, when the shutdown voltage has crossed the threshold. To minimize the supply current while in the shutdown state, the Shutdown pin should be driven to GND or left floating. If the Shutdown pin is not driven to GND, the amount of additional resistor current due to the internal shutdown resistor can be found by Equation 1 below. (VSD - GND) / 60k (1) With only a 0.5V difference, an additional 8.3A of current will be drawn while in the shutdown state. GAIN SELECTION FUNCTION The LM4666 has fixed selectable gain to minimize external components, increase flexibility and simplify design. For a differential gain of 6dB, the Gain Select pin should be permanently connected to VDD or driven to a logic high level. For a differential gain of 12dB, the Gain Select pin should be permanently connected to GND or driven to a logic low level. The gain of the LM4666 can be switched while the amplifier is in PLAY mode driving a load with a signal without damage to the IC. The voltage on the Gain Select pin should be switched quickly between GND (logic low) and VDD (logic high) to eliminate any possible audible artifacts from appearing at the output. For typical threshold voltages for the Gain Select function, refer to the Gain Threshold Voltages graph in the Typical Performance Characteristics section. Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD Submit Documentation Feedback 11 LM4666, LM4666SDBD SNAS189A - MAY 2004 - REVISED MAY 2013 www.ti.com CIRCUIT CONFIGURATIONS Figure 26. Single-Ended Input with Low Gain Selection Configuration Figure 27. Differential Input with Low Gain Selection Configuration 12 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD LM4666, LM4666SDBD www.ti.com SNAS189A - MAY 2004 - REVISED MAY 2013 REFERENCE DESIGN BOARD SCHEMATIC Figure 28. In addition to the minimal parts required for the application circuit, a measurement filter is provided on the evaluation circuit board so that conventional audio measurements can be conveniently made without additional equipment. This is a balanced input, grounded differential output low pass filter with a 3dB frequency of approximately 35kHz and an on board termination resistor of 300 (see Figure 28). Note that the capacitive load elements are returned to ground. This is not optimal for common mode rejection purposes, but due to the independent pulse format at each output there is a significant amount of high frequency common mode component on the outputs. The grounded capacitive filter elements attenuate this component at the board to reduce the high frequency CMRR requirement placed on the analysis instruments. Even with the grounded filter the audio signal is still differential necessitating a differential input on any analysis instrument connected to it. Most lab instruments that feature BNC connectors on their inputs are NOT differential responding because the ring of the BNC is usually grounded. The commonly used Audio Precision analyzer is differential but its ability to accurately reject fast pulses of 160ns width is questionable necessitating the on board measurement filter. When the signal needs to be single-ended, use an audio signal transformer to convert the differential output to a single ended output. Depending on the audio transformer's characteristics, there may be some attenuation of the audio signal which needs to be taken into account for correct measurement of performance. Measurements made at the output of the measurement filter suffer attenuation relative to the primary, unfiltered outputs even at audio frequencies. This is due to the resistance of the inductors interacting with the termination resistor (300) and is typically about -0.35dB (4%). In other words, the voltage levels and corresponding power levels indicated through the measurement filter are slightly lower than those that actually occur at the load placed on the unfiltered outputs. This small loss in the filter for measurement gives a lower output power reading than what is really occurring on the unfiltered outputs and its load. Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD Submit Documentation Feedback 13 LM4666, LM4666SDBD SNAS189A - MAY 2004 - REVISED MAY 2013 www.ti.com The AUX-0025 Switching Amplifier Measurement Filter from Audio Precision may be used instead of the on board measurement filter. The AUX-0025 filter should be connected to the high current direct outputs on the evaluation board and in series with the measurement equipment. Attaching oscilloscope probes on the outputs of the AUX-0025 filter will display the audio waveforms. The AUX-0025 filter may also be connected to the on board filter without any adverse effects. LM4666 NHK0014A BOARD ARTWORK Figure 29. Composite View Figure 30. Silk Screen 14 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD LM4666, LM4666SDBD www.ti.com SNAS189A - MAY 2004 - REVISED MAY 2013 Figure 31. Top Layer Figure 32. Internal Layer 1, GND Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD Submit Documentation Feedback 15 LM4666, LM4666SDBD SNAS189A - MAY 2004 - REVISED MAY 2013 www.ti.com Figure 33. Internal Layer 2, VDD Figure 34. Bottom Layer 16 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD LM4666, LM4666SDBD www.ti.com SNAS189A - MAY 2004 - REVISED MAY 2013 REVISION HISTORY Changes from Original (May 2013) to Revision A * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 16 Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4666 LM4666SDBD Submit Documentation Feedback 17 PACKAGE OPTION ADDENDUM www.ti.com 9-Aug-2013 PACKAGING INFORMATION Orderable Device Status (1) LM4666SD/NOPB ACTIVE Package Type Package Pins Package Drawing Qty WSON NHK 14 1000 Eco Plan Lead/Ball Finish (2) Green (RoHS & no Sb/Br) MSL Peak Temp Op Temp (C) Device Marking (3) CU SN Level-1-260C-UNLIM (4/5) -40 to 85 L4666 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 12-Aug-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM4666SD/NOPB Package Package Pins Type Drawing WSON NHK 14 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 1000 178.0 12.4 Pack Materials-Page 1 3.3 B0 (mm) K0 (mm) P1 (mm) 4.3 1.0 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 12-Aug-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4666SD/NOPB WSON NHK 14 1000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA NHK0014A SDA14A (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM4666SD LM4666SD/NOPB LM4666SDBD LM4666SDX LM4666SDX/NOPB