Data Sheet No. PD10049 revI Series PVA13NPbF Microelectronic Power IC HEXFET Power MOSFET Photovoltaic Relay (R) Single-Pole, Normally-Open, 0-100V AC/DC, 375mA General Description The PVA13 Series AC Relay (PVA) is a singlepole, normally open, solid-state replacement for electromechanical relays used for general purpose switching of analog signals. It utilizes International Rectifier's HEXFET power MOSFETs as the output switches, driven by an integrated circuit photovoltaic generator of novel construction. The output switch is controlled by radiation from a GaAlAs light emitting diode (LED), which is optically isolated from the photovoltaic generator. The PVA13 Series overcomes the limitations of both conventional electromechanical and reed relays by offering the solid state advantages of long life, fast operating speed, low pick up power, bounce-free operation, low thermal offset voltages and miniature package. These advantages allow product improvement and design innovations in many applications such as process control, multiplexing, automatic test equipment and data acquisition. The PVA13 can switch analog signals from thermocouple level to 100 Volts peak AC or DC polarity. Signal frequencies into the RF range are easily controlled and switching rates up to 450Hz are achievable. The extremely small thermally generated offset voltages allow increased measurement accuracies. These relays are packaged in 8-pin, molded DIP packages and available with either thru-hole or surface-mount ("gull-wing") leads, in plastic shipping tubes. Applications Process Control Data Acquisition Test Equipment Multiplexing and Scanning Features Bounce-Free Operation 1010 Off-State Resistance 1,000 V/sec dv/dt 5 mA Input Sensitivity 4,000 VRMS I/O Isolation Solid-State Reliability UL Recognized ESD Tolerance: 4000V Human Body Model 500V Machine Model Part Identification PVA1352NPbF PVA1354NPbF thru-hole PVA1352NSPbF PVA1354NSPbF surface-mount (gull-wing) PVA1354NS-TPbF surface-mount, tape and reel (HEXFET is the registered trademark for International Rectifier Power MOSFETs) www.irf.com 1 Series PVA13NPbF Electrical Specifications (-40C TA +85C unless otherwise specified) INPUT CHARACTERISTICS Minimum Control Current (see figures 1 and 2) For 325mA Continuous Load Current For 370mA Continuous Load Current For 190mA Continuous Load Current Maximum Control Current for Off-State Resistance at 25C PVA1352N Units DC mA@25C mA@40C mA@85C A(DC) 2 5 5 10 Control Current Range (Caution: current limit input LED. See figure 6) 2.0 to 25 mA(DC) 6.0 V(DC) Maximum Reverse Voltage OUTPUT CHARACTERISTICS PVA1354N PVA1352N PVA1354N Units Operating Voltage Range 0 to 100 V(peak) Maxiumum Load Current 40C, I LED 5mA 375 mA(DC) Maximum T(on) @ 12mA Control, 50 mA Load, 50 VDC 150 s Maximum T(off) @ 12mA Control, 50 mA Load, 50 VDC 125 s Response Time @25C (see figures 7 and 8) Minimum Off-state Resistance 25C @ 80 VDC (see figure 5) 5 Maximum On-state Resistance 25C (Pulsed) (figure 4) 50 mA Load, 5mA Control 10 8 10 10 Maximum Thermal Offset Voltage @ 5.0mA Control 0.2 volts Minimum Off-State dv/dt 1000 V/s Typical Output Capacitance (see figure 9) 11pF @ 50VDC GENERAL CHARACTERISTICS (PVA1352N and PVA1354N) Units Dielectric Strength: Input-Output 4000 VRMS Insulation Resistance: Input-Output @ 90VDC 1012 @ 25C - 50% RH Maximum Capacitance: Input-Output 1.0 pF Max. Pin Soldering Temperature (1.6mm below seating plane, 10 seconds max.) Ambient Temperature Range: +260 Operating -40 to +85 Storage -40 to +100 C International Rectifier does not recommend the use of this product in aerospace, avionics, military or life support applications. Users of this International Rectifier product in such applications assume all risks of such use and indemnify International Rectifier against all damages resulting from such use. www.irf.com 2 Series PVA13NPbF 500 Max. Load Current (mA) 400 350 ILED=10mA 300 250 ILED=5mA 200 150 ILED=2mA 100 50 Max. Load Current (mA) 450 0 0 20 40 60 80 100 ILED (mA) Ambient Temperature (C) Figure 1. Current Derating Curves Figure 2. Typical Control Current Requirements Load Current (mA) 700 Pulsed, 25C 600 500 25C 40C 60C 400 300 85C 200 I LED = 5mA, Forced Air 100 0 0.0 0.5 1.0 1.5 2.0 2.5 VDD (volts) Figure 3.Typical On Characteristics www.irf.com Rd(on) (ormalized to 25C) 800 3.0 Ambient Temperature (C) Figure 4. Typical Normalized On-Resistance 3 IDOff/IDOff 25C Input Current (mA) Series PVA13NPbF LED Forward Voltage Drop (Volts DC) Ambient Temperature (C) Figure 6. Input Characteristics Figure 5. Normalized Off-State Leakage (Current Controlled) Delay Time (S) 1000 Ton Tdly 100 Toff 10 0 5 10 15 20 I LED (mA) Figure 7.Typical Delay Times www.irf.com Figure 8. Delay Time Definitions 4 Series PVA13NPbF 100 Wiring Diagram Typical Capacitance (pF) 90 80 70 60 50 40 30 20 10 0 0 10 20 30 40 50 VDD Drain to Drain Voltage Figure 9. Typical Output Capacitance Case Outlines 01-2013 00 (MS-001AB) www.irf.com 5 Series PVA13NPbF 01-2019 00 IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 Data and specifications subject to change without notice. 2/2008 www.irf.com 6