PCB Sensors E3S-LS3@ CSM_E3S-LS3__DS_E_3_1 Reliable Detection Unaffected by PCB Holes or Notches * High-limit E3S-LS3@ is suitable for incorporation in devices. * Wide-range E3S-LS3@W is ideal for detecting tall components mounted on boards. * Timer function models available. Be sure to read Safety Precautions on page 4. Ordering Information Sensors Sensing method Red light Appearance Convergentreflective Connection method Sensing distance 20 to 35 mm * Pre-wired (2 m) 10 to 60 mm * Timer function Without With Without With Model NPN output E3S-LS3N 2M E3S-LS3NT 2M E3S-LS3NW 2M E3S-LS3NWT 2M PNP output E3S-LS3P 2M E3S-LS3PT 2M E3S-LS3PW 2M E3S-LS3PWT 2M * For white paper: 80 x 80 mm. 1 E3S-LS3@ Ratings and Specifications Sensing method Item Convergent-reflective Model Sensing distance E3S-LS3N(T)/-LS3P(T) E3S-LS3NW(T)/-LS3PW(T) White paper * 20 to 35 mm 10 to 60 mm Black paper * 20 to 30 mm 15 to 50 mm Light source (wavelength) Red LED (660 nm) Power supply voltage 12 to 24 VDC10%, ripple (p-p) 10% max. Current consumption 25 mA max. Control output Load power supply voltage: 24 VDC max., Load current: 100 mA max., (Residual voltage: 1 V max. for NPN output or 2 V max. for PNP output) Open collector output configuration: NPN or PNP output depending on the model, Operating mode: Light-ON Response time Operate or reset: 1 ms max. Timer function (only models with timer function) OFF-delay range: 0.1 to 1.0 s (adjustable) Ambient illumination (Receiver side) Incandescent lamp: 5,000 lux max. Ambient temperature range Operating: -10 to 55C (with no icing or condensation) Storage: -25 to 70C (with no icing or condensation) Ambient humidity range Operating: 35% to 85% (with no condensation) Storage: 35% to 95% (with no condensation) Insulation resistance 20 M min. (at 500 VDC) Dielectric strength 1,000 VAC at 50/60 Hz for 1 minute Vibration resistance Destruction: 10 to 55 Hz with a 1.5-mm double amplitude for 2 hrs each in X, Y and Z directions Shock resistance Destruction: 500 m/s2, 3 times each in X, Y and Z directions Degree of protection IEC 60529 IP40 Connection method Pre-wired (standard length: 2 m) Weight (packed state) Material Approx. 80 g Case ABS (Acrylonitril Butadiene Styrene) Lens Methacrylic resin Accessories Instruction manual, M3 screws, Adjustment screwdriver (only models with timer function) * For 80 x 80 mm. Engineering Data (Typical) Sensing distance (mm) Sensing Distance vs. Materials 80 E3S-LS3@(T) 70 E3S-LS3@W(T) 60 50 40 30 20 10 0 White paper Black paper Black SUS PWB with green PWB resist Materials 2 E3S-LS3@ 15 Operating Range (Up and Down) Set distance Y (mm) Set distance Y (mm) Operating Range (Left and Right) Sensing object: White paper, 80 x 80 mm Y 12 X E3S-LS3@W(T) 9 6 E3S-LS3@(T) 3 -15 -3 20 30 40 50 60 X E3S-LS3@W(T) -6 E3S-LS3@(T) -3 0 10 Y -9 0 0 Sensing object: White paper, 80 x 80 mm -12 0 10 20 30 40 50 60 70 70 3 -6 6 -9 9 -12 12 -15 15 Set distance X (mm) Set distance X (mm) Excess Gain vs. Set Distance Spot Diameter vs. Sensing Distance Sensing object: White paper, 80 x 80 mm 10 Spot diameter (mm) Excess gain ratio (times) (E3S-LS3@(T), E3S-LS3@W(T) (Common) 100 35 30 25 Direction L d 20 L 15 Operating 1 level E3S-LS3@(T) 10 Direction d E3S-LS3@W(T) 0.1 5 0 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 10 20 30 Set distance (mm) 40 50 60 70 Set distance (mm) I/O Circuit Diagrams NPN Output Model Operation mode Timing charts Incident light No incident light Operation indicator ON (orange) OFF E3S-LS3N E3S-LS3NW Output transistor Light-ON E3S-LS3NT E3S-LS3NWT Output circuit ON OFF Incident light No incident light Operation indicator ON (orange) OFF Brown 12 to 24 VDC Operation indicator (orange) T Photoelectric Sensor main circuit Load Black OUT Z Blue 0V ON OFF T: OFF-delay timer (0.1 to 1.0 s) Output transistor 3 E3S-LS3@ PNP Output Operation mode Model Timing charts Output circuit Incident light No incident light Operation indicator ON (orange) OFF E3S-LS3P E3S-LS3PW Light-ON E3S-LS3PT E3S-LS3PWT Operation indicator (orange) ON OFF Output transistor Incident light No incident light Operation indicator ON (orange) OFF Photoelectric Sensor main circuit T Brown 12 to 24 VDC Black OUT Load Blue 0V ON OFF T: OFF-delay timer (0.1 to 1.0 s) Output transistor Safety Precautions Refer to Warranty and Limitations of Liability. WARNING This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings (Unit: mm) Dimensions E3S-LS3N(T)/E3S-LS3P(T) E3S-LS3NW(T)/E3S-LS3PW(T) Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified. Operation Indicator (orange) Timer adjuster * 10 14.2 8.5 dia. Mounting Holes Two, 3.6 dia. 19.3 11.8 5.4 0.3 28 3 28 34 3 Two, M3 Mounting Holes 10 Receiver Emitter 4-dia.vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2, Insulator diameter: 1.1 mm), Standard length: 2 m * The timer adjuster is only for models with the timer function. 4 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: * Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. * Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. * Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. 2008.11 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2008 All Right Reserved.