308 Constitution Drive
Menlo Park, CA 94025-1164
Phone: 800-227-4856
www.circuitprotection.com
PolySwitch®
PTC Devices
Overcurrent Protection Devi ce
Raychem Circuit Protection Products
PRODUCT: AGRF1200
DOCUMENT: SCD 25239
PCN: D73591
REV LETTER: B
REV DATE: MAY 15, 2007
PAGE NO.: 1 OF 2
Specification Status: RELEASED
Electrical Rating
Voltage: 16VDC MAX
Insulating Material:
Cured, Flame Retardant Epoxy Polymer
Lead Material:
18 AWG Tin Plated Copper
( 1.0 mm [0.040] nom. diameter)
Part Marking:
Raychem Logo
and Voltage
Lot Identification
Part Identification
GF12
(can be on back)
16
TABLE I. INSTALLATION ENVELOPE DIMENSIONS:
A B C D E F G
MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX TYP MIN MAX
mm: -- 17.5 -- 28.8 9.4 10.9 7.6 -- -- 3.5 1.4 -- 4.83
in*: -- (0.69) -- (1.14) (0.37) (0.43) (0.30) -- -- (0.14) (0.06) -- (0.190)
*Rounded off approximation
TABLE II. PERFORMANCE RATINGS:
CURRENT RATINGS TIME TO
TRIP INITIAL
RESISTANCE R1 MAX
1 HR. POST TRIP
RESISTANCE
STANDARD TRIP
RA MAX
TRIPPED-STATE
POWER
DISSIPATION
AMPS
AT 25°C SECONDS
AT 25°C, 60 A OHMS
AT 25°C OHMS
AT 25°C OHMS
AT 25°C WATTS AT
25°C
HOLD
AT
R1
MAX
HOLD
AT
RA
MAX
TRIP MAX MIN MAX TYP
12.0 11.5 22.1 8.0 0.0030 0.0057 0.0086 0.0091 4.2
Reference Documents: PS400, PS300 (reference for R1 MAX)
Precedence: This specification takes precedence over documents referenced herein.
Effectivity: Reference documents shall be the issue in effect on the date of invitation for bid.
CAUTION: Operation beyond the rated voltage or current may result in rupture, electrical arcing or flame.
Materials Information
ROHS Compliant ELV Compliant Pb-Free
© 2004, 2007 Tyco Electronics Corporation. All rights reserved.
308 Constitution Drive
Menlo Park, CA 94025-1164
Phone: 800-227-4856
www.circuitprotection.com
PolySwitch®
PTC Devices
Overcurrent Protection Devi ce
Raychem Circuit Protection Products
PRODUCT: AGRF1200
DOCUMENT: SCD 25239
PCN: D73591
REV LETTER: B
REV DATE: MAY 15, 2007
PAGE NO.: 2 OF 2
TABLE III. AUTOMOTIVE SPECIFIC STRESS TESTS AND TEST CONDITIONS:
ELECTRICAL STRESS T ESTS
TEST CONDIT IONS (see note 2)
ESD Voltage Withstand
(see note 1) 25kV
Short Circuit Fault Current Durability 25 cycles, 16V, 200A
Fault Current Durability
350 cycles, 16V/100A
End-of-life Mode Verification
1750 cycles, 16V/100A
Jump Start Endurance
(see note 1) 3 cycles, 26V, 1 minute duration
Load Dump Endurance
(see note 1) 10 cycles, 86.5V
Note 1: The PolySwitch devices are tested in series with a load resistance and the voltages specified in the test conditions are
shared between the PolySwitch device and the load resistance as specified in PS400.
Note 2: Please refer to Appendix A of PS400 for the detailed test procedures
