1997 Nov 17 1
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
MKT RADIAL EPOXY LACQUERED TYPE PITCH 5/7.5/10/15/22.5/27.5 mm
Fig.1 Simplified outlines.
handbook, full pagewidth
465
(5 mm) 466
(7.5 mm) 467
(10 mm) 468
(15 - 22.5 -27.5 mm)
CBA094
APPLICATIONS
•Blocking and coupling
•Bypass and energy reservoir.
FEATURES
•Low-inductive wound cell of
metallized (PETP) film
•Cell protected by epoxy lacquer
•Radial leads of solder-coated wire
•Withstands solvents and rinsing
liquids
•Small stand-off pips allow removal
of solder flux.
QUICK REFERENCE DATA
DESCRIPTION VALUE
Capacitance range (E12 series) 0.01 to 10 µF
Capacitance tolerance ±10%; ±5%
Rated voltage URdc 100 V; 250 V; 400 V; 630 V
Climatic category 55/100/56
Rated temperature 85 °C
Maximum application temperature 100 °C
Tangent of loss angle at 10 kHz 100 ×10−4
Reference specifications IEC 384-2
Performance grade grade 1 (long life)
1997 Nov 17 2
Philips Components Product specification
Metallized polyester film capacitors MKT 465
MKT 465 GENERAL DATA PITCH 5 mm
Fig.2 Outline with kinked leads.
handbook, halfpage
seating plane
hole Ø1.0 mm
lb
P
h
lt
Ødt
CBA095
A
α
ϒ
0 ≤ α < 50°
Fig.3 Outline with straight leads.
handbook, halfpage
seating plane
hole Ø1.0
b
Ø1.3
h
lt
Ødt
P
l
≤1.5
CBA096
Specific reference data for the 100 V DC capacitors
Available 100 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.1 µF≤75 ×10−4≤120 ×10−4≤200 ×10−4
0.1 µF<C≤0.27 µF≤75 ×10−4≤120 ×10−4≤225 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 120 V/µs
R between leads, for C ≤0.33 µF >15000 MΩ
PACKAGING DIMENSIONS LEAD
CONFIGURATION C-tol FIRST 9 DIGITS OF
CATALOGUE
NUMBER ORDERING
Ammopack H = 16.0 mm; note 1 kinked
±10% 2222 465 06... on request
±5% 2222 465 07... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 465 04... on request
±5% 2222 465 05... on request
Ammopack H = 18.5 mm; note 1 straight
±10% 2222 465 02... on request
±5% 2222 465 03... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 465 00... on request
±5% 2222 465 01... on request
1997 Nov 17 3
Philips Components Product specification
Metallized polyester film capacitors MKT 465
URdc = 100 V; URac =63V loose and taped
Notes
1. Dimensions and SPQ in brackets for straight leads.
2. H = in-tape height; 16.0 mm for kinked and 18.5 mm for straight leads.
C
(µF)
DIMENSIONS(1)
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 465 ..... AND PACKAGING
AMMOPACK; H = 16 mm(2) LOOSE IN BOX
kinked leads
SPQ SPQ(1)
last 5 digits of
catalogue number
C-tol = ±10% C-tol = ±5%
Pitch = 5.0 ±0.4 mm; dt= 0.50 ±0.05 mm; A = 1.7 ±0.3 mm
0.01
3.5 ×12.5 (7.5) ×7.3 0.3
06103 07103
1500 1000 (1000)
0.012 06123 07123
0.015 06153 07153
0.018 06183 07183
0.022 06223 07223
0.027 06273 07273
0.033 06333 07333
0.039 06393 07393
0.047 06473 07473
0.056 06563 07563
0.068
3.7 ×12.5 (7.5) ×7.3 0.3
06683 07683
1500 1000 (1000)
0.082 06823 07823
0.1 06104 07104
0.12 06124 07124
0.15 3.7 ×13.0 (8.0) ×7.3 0.3 06154 07154 1500 1000 (1000)
0.18 3.7 ×13.5 (8.5) ×7.3 0.4 06184 07184 1500 1000 (1000)
0.22 4.2 ×13.5 (8.5) ×7.3 0.4 06224 07224 1250 1000 (1000)
0.27 4.5 ×14.0 (9.0) ×7.3 0.4 06274 07274 1250 1000 (1000)
1997 Nov 17 4
Philips Components Product specification
Metallized polyester film capacitors MKT 465
MKT 465 GENERAL DATA PITCH 5 mm (bent back leads)
Specific reference data for the 100 V DC capacitors
Available 100 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
0.12 µF<C≤0.47 µF≤75 ×10−4≤120 ×10−4≤225 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 40 V/µs
R between leads, for C ≤0.33 µF >15000 MΩ
RC between leads, for C >0.33 µF >5000 s
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Ammopack H = 16.0 mm; note 1 ±10% 2222 465 10... on request
±5% 2222 465 11... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 465 08... on request
±5% 2222 465 09... on request
Fig.4 Outline.
handbook, full pagewidth
CBA066
seating plane(1)
b
I
∅dt
AP
h
lt
(1) Hole diameter = 1.0 mm.
1997 Nov 17 5
Philips Components Product specification
Metallized polyester film capacitors MKT 465
URdc = 100 V; URac =63V loose and taped
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 465 ..... AND PACKAGING
AMMOPACK; H = 16 mm LOOSE IN BOX
last 5 digits of
catalogue number SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 5.0 ±0.4 mm; dt= 0.60 ±0.06 mm; A = 1.7 ±0.3 mm
0.12 4.5 ×13.5 ×10.0 0.5 10124 11124 1250 1500
0.15 5.0 ×13.5 ×10.0 0.5 10154 11154 1000 1500
0.18 4.0 ×13.0 ×10.0 0.4 10184 11184 1500 2000
0.22 0.5 10224 11224
0.27 4.5 ×13.5 ×10.0 0.5 10274 11274 1250 1500
0.33 0.5 10334 11334
0.39 5.0 ×14.0 ×10.0 0.7 10394 11394 1000 1500
0.47 5.5 ×14.5 ×10.0 0.8 10474 11474 1000 1500
1997 Nov 17 6
Philips Components Product specification
Metallized polyester film capacitors MKT 465
MKT 465 GENERAL DATA PITCH 5 mm (bent back leads)
Specific reference data for the 250 V DC capacitors
Available 250 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.1 µF≤75 ×10−4≤120 ×10−4≤200 ×10−4
0.1 µF<C≤0.15 µF≤75 ×10−4≤120 ×10−4≤225 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 120 V/µs
R between leads, for C ≤0.33 µF >30000 MΩ
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Ammopack H = 16.0 mm; note 1 ±10% 2222 465 22... on request
±5% 2222 465 23... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 465 20... on request
±5% 2222 465 21... on request
Fig.5 Outline.
handbook, full pagewidth
CBA066
seating plane(1)
b
I
∅dt
AP
h
lt
(1) Hole diameter = 1.0 mm.
1997 Nov 17 7
Philips Components Product specification
Metallized polyester film capacitors MKT 465
URdc = 250 V; URac = 160 V loose and taped
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 465 ..... AND PACKAGING
AMMOPACK; H = 16 mm LOOSE IN BOX
last 5 digits of
catalogue number SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 5.0 ±0.4 mm; dt= 0.60 ±0.06 mm; A = 1.7 ±0.3 mm
0.01 5.5 ×13.5 ×10.0 0.7 22103 23103 1000 1500
0.012 4.0 ×12.5 ×10.0 0.4 22123 23123 1500 2000
0.015 4.5 ×13.0 ×10.0 0.5 22153 23153 1250 1500
0.018 4.5 ×13.5 ×10.0 0.6 22183 23183 1250 1500
0.022 5.0 ×13.5 ×10.0 0.7 22223 23223 1000 1500
0.027 5.5 ×14.0 ×10.0 0.7 22273 23273 1000 1250
0.033 4.0 ×13.0 ×10.0 0.4 22333 23333 1500 2000
0.039 4.5 ×13.0 ×10.0 0.5 22393 23393 1250 1500
0.047 4.5 ×13.5 ×10.0 0.6 22473 23473 1250 1500
0.056 5.0 ×13.5 ×10.0 0.7 22563 23563 1000 1500
0.068 5.5 ×14.0 ×10.0 0.7 22683 23683 1000 1250
0.082 4.5 ×13.0 ×10.0 0.5 22823 23823 1250 1500
0.1 5.0 ×13.5 ×10.0 0.6 22104 23104 1000 1500
0.12 5.5 ×14.0 ×10.0 0.6 22124 23124 1000 1250
0.15 5.5 ×15.5 ×10.0 0.7 22154 23154 1000 1250
1997 Nov 17 8
Philips Components Product specification
Metallized polyester film capacitors MKT 465
MKT 465 GENERAL DATA PITCH 5 mm (bent back leads)
Specific reference data for the 400 V DC capacitors
Available 400 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.056 µF≤75 ×10−4≤120 ×10−4≤200 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 170 V/µs
R between leads, for C ≤0.33 µF >30000 MΩ
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Ammopack H = 16.0 mm; note 1 ±10% 2222 465 34... on request
±5% 2222 465 35... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 465 32... on request
±5% 2222 465 33... on request
Fig.6 Outline.
handbook, full pagewidth
CBA066
seating plane(1)
b
I
∅dt
AP
h
lt
(1) Hole diameter = 1.0 mm.
1997 Nov 17 9
Philips Components Product specification
Metallized polyester film capacitors MKT 465
URdc = 400 V; URac = 200 V loose and taped
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 465 ..... AND PACKAGING
AMMOPACK; H = 16 mm LOOSE IN BOX
last 5 digits of
catalogue number SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 5.0 ±0.4 mm; dt= 0.60 ±0.06 mm; A = 1.7 ±0.3 mm
0.01 5.5 ×13.5 ×10.0 0.7 34103 35103 1000 1500
0.012 4.0 ×12.5 ×10.0 0.4 34123 35123 1500 2000
0.015 4.0 ×13.0 ×10.0 0.5 34153 35153 1500 2000
0.018 4.5 ×13.0 ×10.0 0.6 34183 35183 1250 1500
0.022 5.0 ×13.5 ×10.0 0.7 34223 35223 1000 1500
0.027 4.0 ×12.5 ×10.0 0.4 34273 35273 1500 2000
0.033 4.5 ×13.0 ×10.0 0.5 34333 35333 1250 1500
0.039 5.0 ×13.5 ×10.0 0.6 34393 35393 1000 1500
0.047 34473 35473 1000 1500
0.056 5.5 ×14.0 ×10.0 0.7 34563 35563 1000 1250
1997 Nov 17 10
Philips Components Product specification
Metallized polyester film capacitors MKT 466
MKT 466 GENERAL DATA PITCH 7.5 mm
Fig.7 Outline with kinked leads.
handbook, halfpage
seating plane
hole Ø1.0 mm
l
h
lt
Ødt
A
b
CBA098
P
α
ϒ
0 ≤ α < 50°
Fig.8 Outline with straight leads.
handbook, halfpage
seating plane
hole Ø1.0 mm
Ødt
P
l
lt
h
b
Ø1.3
≤1.5
CBA099
Specific reference data for the 100 V DC capacitors
Available 100 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
0.12 µF<C≤0.47 µF≤75 ×10−4≤120 ×10−4≤225 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 40 V/µs
R between leads, for C ≤0.33 µF >15000 MΩ
RC between leads, for C >0.33 µF >5000 s
PACKAGING DIMENSIONS LEAD
CONFIGURATION C-tol FIRST 9 DIGITS OF
CATALOGUE
NUMBER ORDERING
Ammopack H = 16.0 mm; note 1 kinked
±10% 2222 466 06... on request
±5% 2222 466 07... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 466 04... on request
±5% 2222 466 05... on request
Ammopack H = 18.5 mm; note 1 straight
±10% 2222 466 02... on request
±5% 2222 466 03... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 466 00... on request
±5% 2222 466 01... on request
1997 Nov 17 11
Philips Components Product specification
Metallized polyester film capacitors MKT 466
URdc = 100 V; URac =63V loose and taped
Notes
1. Dimensions and SPQ in brackets for straight leads.
2. H = in-tape height; 16.0 mm for kinked and 18.5 mm for straight leads.
C
(µF)
DIMENSIONS(1)
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 466 ..... AND PACKAGING
AMMOPACK; H = 16 mm(2) LOOSE IN BOX
kinked leads
SPQ SPQ(1)
last 5 digits of
catalogue number
C-tol = ±10% C-tol = ±5%
Pitch = 7.5 ±0.4 mm; dt= 0.60 ±0.06 mm; A = 2.0 ±0.5 mm
0.12 4.5 ×13.0 (9.0) ×10.0 0.5 06124 07124 1250 1500 (1000)
0.15 5.0 ×13.0 (9.0) ×10.0 0.5 06154 07154 1000 1500 (1000)
0.18 4.0 ×13.0 (9.0) ×10.0 0.4 06184 07184 1500 2000 (1000)
0.22 4.0 ×13.5 (9.5) ×10.0 0.5 06224 07224 1500 2000 (1000)
0.27 4.5 ×13.5 (9.5) ×10.0 0.5 06274 07274 1250 1500 (1000)
0.33 4.5 ×13.5 (9.5) ×10.0 0.5 06334 07334 1250 1500 (1000)
0.39 5.0 ×14.0 (10.0) ×10.0 0.7 06394 07394 1000 1500 (1500)
0.47 5.5 ×14.5 (10.5) ×10.0 0.8 06474 07474 1000 1250 (1500)
1997 Nov 17 12
Philips Components Product specification
Metallized polyester film capacitors MKT 466
MKT 466 GENERAL DATA PITCH 7.5 mm
Fig.9 Outline with kinked leads.
handbook, halfpage
seating plane
hole Ø1.0 mm
l
h
lt
Ødt
A
b
CBA098
P
α
ϒ
0 ≤ α < 50°
Fig.10 Outline with straight leads.
handbook, halfpage
seating plane
hole Ø1.0 mm
Ødt
P
l
lt
h
b
Ø1.3
≤1.5
CBA099
Specific reference data for the 250 V DC capacitors
Available 250 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.1 µF≤75 ×10−4≤120 ×10−4≤200 ×10−4
0.1 µF<C≤0.15 µF≤75 ×10−4≤120 ×10−4≤225 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 120 V/µs
R between leads, for C ≤0.33 µF >30000 MΩ
PACKAGING DIMENSIONS LEAD
CONFIGURATION C-tol FIRST 9 DIGITS OF
CATALOGUE
NUMBER ORDERING
Ammopack H = 16.0 mm; note 1 kinked
±10% 2222 466 18... on request
±5% 2222 466 19... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 466 16... on request
±5% 2222 466 17... on request
Ammopack H = 18.5 mm; note 1 straight
±10% 2222 466 14... on request
±5% 2222 466 15... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 466 12... on request
±5% 2222 466 13... on request
1997 Nov 17 13
Philips Components Product specification
Metallized polyester film capacitors MKT 466
URdc = 250 V; URac = 160 V loose and taped
Notes
1. Dimensions and SPQ in brackets for straight leads.
2. H = in-tape height; 16.0 mm for kinked and 18.5 mm for straight leads.
C
(µF)
DIMENSIONS(1)
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 466 ..... AND PACKAGING
AMMOPACK; H = 16 mm(2) LOOSE IN BOX
kinked leads
SPQ SPQ(1)
last 5 digits of
catalogue number
C-tol = ±10% C-tol = ±5%
Pitch = 7.5 ±0.4 mm; dt= 0.60 ±0.06 mm; A = 2.0 ±0.5 mm
0.01 5.5 ×13.5 (9.5) ×10.0 0.7 18103 19103 1000 1500 (1500)
0.012 4.0 ×13.0 (9.0) ×10.0 0.4 18123 19123 1500 2000 (1000)
0.015 4.5 ×13.0 (9.0) ×10.0 0.5 18153 19153 1250 1500 (1000)
0.018 4.5 ×13.5 (9.5) ×10.0 0.6 18183 19183 1250 1500 (1000)
0.022 5.0 ×14.0 (10.0) ×10.0 0.7 18223 19223 1000 1500 (1500)
0.027 5.5 ×14.0 (10.0) ×10.0 0.7 18273 19273 1000 1250 (1500)
0.033 4.0 ×13.0 (9.0) ×10.0 0.4 18333 19333 1500 2000 (1000)
0.039 4.5 ×13.0 (9.0) ×10.0 0.5 18393 19393 1250 1500 (1000)
0.047 4.5 ×13.5 (9.5) ×10.0 0.6 18473 19473 1250 1500 (1000)
0.056 5.0 ×14.0 (10.0) ×10.0 0.7 18563 19563 1000 1500 (1500)
0.068 5.5 ×14.0 (10.0) ×10.0 0.7 18683 19683 1000 1250 (1500)
0.082 4.5 ×13.0 (9.0) ×10.0 0.5 18823 19823 1250 1500 (1000)
0.1 5.0 ×13.5 (9.5) ×10.0 0.6 18104 19104 1000 1500 (1000)
0.12 5.5 ×14.0 (10.0) ×10.0 0.6 18124 19124 1000 1250 (1500)
0.15 5.5 ×15.5 (11.5) ×10.0 0.7 18154 19154 1000 1250 (1500)
1997 Nov 17 14
Philips Components Product specification
Metallized polyester film capacitors MKT 466
MKT 466 GENERAL DATA PITCH 7.5 mm
Fig.11 Outline with kinked leads.
handbook, halfpage
seating plane
hole Ø1.0 mm
l
h
lt
Ødt
A
b
CBA098
P
α
ϒ
0 ≤ α < 50°
Fig.12 Outline with straight leads.
handbook, halfpage
seating plane
hole Ø1.0 mm
Ødt
P
l
lt
h
b
Ø1.3
≤1.5
CBA099
Specific reference data for the 400 V DC capacitors
Available 400 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.056 µF≤75 ×10−4≤120 ×10−4≤200 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 170 V/µs
R between leads, for C ≤0.33 µF >30000 MΩ
PACKAGING DIMENSIONS LEAD
CONFIGURATION C-tol FIRST 9 DIGITS OF
CATALOGUE
NUMBER ORDERING
Ammopack H = 16.0 mm; note 1 kinked
±10% 2222 466 30... on request
±5% 2222 466 31... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 466 28... on request
±5% 2222 466 29... on request
Ammopack H = 18.5 mm; note 1 straight
±10% 2222 466 26... on request
±5% 2222 466 27... on request
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 466 24... on request
±5% 2222 466 25... on request
1997 Nov 17 15
Philips Components Product specification
Metallized polyester film capacitors MKT 466
URdc = 400 V; URac = 200 V loose and taped
Notes
1. Dimensions and SPQ in brackets for straight leads.
2. H = in-tape height; 16.0 mm for kinked and 18.5 mm for straight leads.
C
(µF)
DIMENSIONS(1)
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 466 ..... AND PACKAGING
AMMOPACK; H = 16 mm(2) LOOSE IN BOX
kinked leads
SPQ SPQ(1)
last 5 digits of
catalogue number
C-tol = ±10% C-tol = ±5%
Pitch = 7.5 ±0.4 mm; dt= 0.60 ±0.06 mm; A = 2.0 ±0.5 mm
0.01 5.5 ×13.5 (9.5) ×10.0 0.7 30103 31103 1000 1500 (1500)
0.012 4.0 ×13.0 (9.0) ×10.0 0.4 30123 31123 1500 2000 (1000)
0.015 0.5 30153 31153
0.018 4.5 ×13.5 (9.5) ×10.0 0.6 30183 31183 1250 1500 (1000)
0.022 5.0 ×14.0 (10.0) ×10.0 0.7 30223 31223 1000 1500 (1500)
0.027 4.0 ×12.5 (8.5) ×10.0 0.4 30273 31273 1500 2000 (1000)
0.033 4.5 ×13.0 (9.0) ×10.0 0.5 30333 31333 1250 1500 (1000)
0.039 5.0 ×13.5 (9.5) ×10.0 0.5 30393 31393 1000 1500 (1000)
0.047 5.0 ×13.5 (9.5) ×10.0 0.6 30473 31473 1000 1500 (1000)
0.056 5.5 ×14.0 (10.0) ×10.0 0.7 30563 31563 1000 1250 (1500)
1997 Nov 17 16
Philips Components Product specification
Metallized polyester film capacitors MKT 467
MKT 467 GENERAL DATA PITCH 10 mm (kinked leads)
Specific reference data for the 100 V DC capacitors
Available 100 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
0.56 µF<C≤1.0 µF≤75 ×10−4≤120 ×10−4−
Rated voltage pulse slope (dU/dt)R at URdc 30 V/µs
RC between leads, for C >0.33 µF >5000 s
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 467 04... preferred
±5% 2222 467 05... preferred
Taped on reel H = 16.0 mm; note 1 ±10% 2222 467 06... on request
±5% 2222 467 07... on request
Fig.13 Outline.
handbook, full pagewidth
seating plane
hole Ø1.0 mm
for Ødt = 0.6 mm
l
Ødt
0 ≤ α < 50°
P
h
lt
α
A
CBA100
b
1997 Nov 17 17
Philips Components Product specification
Metallized polyester film capacitors MKT 467
URdc = 100 V; URac =63V loose and taped
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 467 ..... AND PACKAGING
LOOSE IN BOX; lt= 3.5 ±0.5 mm REEL
last 5 digits of
catalogue number(1) SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 10.0 ±0.4 mm; dt= 0.60 ±0.06 mm; A = 2.0 ±0.5 mm
0.56 4.5 ×13.5 ×12.5 0.5 04564 05564 2000 1300
0.68 5.0 ×14.0 ×12.5 0.6 04684 05684 1500 1200
0.82 5.5 ×14.5 ×12.5 0.7 04824 05824 1500 1100
1.0 6.0 ×15.0 ×12.5 0.7 04105 05105 1250 1000
1997 Nov 17 18
Philips Components Product specification
Metallized polyester film capacitors MKT 467
MKT 467 GENERAL DATA PITCH 10 mm (kinked leads)
Specific reference data for the 250 V DC capacitors
Available 250 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
0.18 µF<C≤0.33 µF≤75 ×10−4≤120 ×10−4≤225 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 120 V/µs
R between leads, for C ≤0.33 µF >30000 MΩ
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 467 16... preferred
±5% 2222 467 17... preferred
Taped on reel H = 16.0 mm; note 1 ±10% 2222 467 18... on request
±5% 2222 467 19... on request
Fig.14 Outline.
handbook, full pagewidth
seating plane
hole Ø1.0 mm
for Ødt = 0.6 mm
l
Ødt
0 ≤ α < 50°
P
h
lt
α
A
CBA100
b
1997 Nov 17 19
Philips Components Product specification
Metallized polyester film capacitors MKT 467
URdc = 250 V; URac = 160 V loose and taped
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 467 ..... AND PACKAGING
LOOSE IN BOX; lt= 3.5 ±0.5 mm REEL
last 5 digits of
catalogue number(1) SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 10.0 ±0.4 mm; dt= 0.60 ±0.06 mm; A = 2.0 +1.0/−0.5 mm
0.18 5.0 ×13.5 ×12.5 0.5 16184 17184 1500 1200
0.22 5.5 ×14.0 ×12.5 0.6 16224 17224 1500 1100
1997 Nov 17 20
Philips Components Product specification
Metallized polyester film capacitors MKT 467
MKT 467 GENERAL DATA PITCH 10 mm (kinked leads)
Specific reference data for the 400 V DC capacitors
Available 400 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.1 µF≤75 ×10−4≤120 ×10−4≤200 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 170 V/µs
R between leads, for C ≤0.33 µF >30000 MΩ
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 467 28... preferred
±5% 2222 467 29... preferred
Taped on reel H = 16.0 mm; note 1 ±10% 2222 467 30... on request
±5% 2222 467 31... on request
Fig.15 Outline.
handbook, full pagewidth
seating plane
hole Ø1.0 mm
for Ødt = 0.6 mm
l
Ødt
0 ≤ α < 50°
P
h
lt
α
A
CBA100
b
1997 Nov 17 21
Philips Components Product specification
Metallized polyester film capacitors MKT 467
URdc = 400 V; URac = 200 V loose and taped
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 467 ..... AND PACKAGING
LOOSE IN BOX; lt= 3.5 ±0.5 mm REEL
last 5 digits of
catalogue number(1) SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 10.0 ±0.4 mm; dt= 0.60 ±0.06 mm; A = 2.0 +1.0/−0.5 mm
0.039 5.0 ×13.5 ×12.5 0.5 28393 29393 1500 1200
0.047 5.5 ×14.0 ×12.5 0.6 28473 29473 1500 1100
0.056 4.0 ×13.0 ×12.5 0.4 28563 29563 2000 1500
0.068 4.5 ×13.0 ×12.5 0.5 28683 29683 2000 1300
0.082 5.0 ×13.5 ×12.5 0.6 28823 29823 1500 1200
0.1 5.5 ×14.0 ×12.5 0.7 28104 29104 1500 1100
1997 Nov 17 22
Philips Components Product specification
Metallized polyester film capacitors MKT 467
MKT 467 GENERAL DATA PITCH 10 mm (kinked leads)
Specific reference data for the 630 V DC capacitors
Available 630 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.047 µF≤75 ×10−4≤120 ×10−4≤200 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 120 V/µs
R between leads, for C ≤0.33 µF >30000 MΩ
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 467 40... preferred
±5% 2222 467 41... preferred
Taped on reel H = 16.0 mm; note 1 ±10% 2222 467 42... on request
±5% 2222 467 43... on request
Fig.16 Outline.
handbook, full pagewidth
seating plane
hole Ø1.0 mm
for Ødt = 0.6 mm
l
Ødt
0 ≤ α < 50°
P
h
lt
α
A
CBA100
b
1997 Nov 17 23
Philips Components Product specification
Metallized polyester film capacitors MKT 467
URdc = 630 V; URac = 250 V loose and taped
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 467 ..... AND PACKAGING
LOOSE IN BOX; lt= 3.5 ±0.5 mm REEL
last 5 digits of
catalogue number(1) SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 10.0 ±0.4 mm; dt= 0.60 ±0.06 mm; A = 2.0 +1.0/−0.5 mm
0.01 4.0 ×12.5 ×12.5 0.4 40103 41103 2000 1500
0.012 4.5 ×13.0 ×12.5 0.5 40123 41123 2000 1300
0.015 5.0 ×13.0 ×12.5 0.5 40153 41153 2000 1200
0.018 5.5 ×13.0 ×12.5 0.5 40183 41183 1500 1100
0.022 4.5 ×13.0 ×12.5 0.5 40223 41223 2000 1300
0.027 5.0 ×13.0 ×12.5 0.5 40273 41273 2000 1200
0.033 5.5 ×13.5 ×12.5 0.6 40333 41333 1500 1100
1997 Nov 17 24
Philips Components Product specification
Metallized polyester film capacitors MKT 468
MKT 468 GENERAL DATA PITCH 15/22.5 mm (kinked leads)
Specific reference data for the 100 V DC capacitors
Available 100 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz
Tangent of loss angle:
C>10.0 µF≤75 ×10−4≤120 ×10−4
Rated voltage pulse slope (dU/dt)R at URdc 20 V/µs
R between leads, for C ≤0.33 µF >5000 s
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 468 04... preferred
±5% 2222 468 05... preferred
Taped on reel H = 16.0 mm; note 1 ±10% 2222 468 06... on request
±5% 2222 468 07... on request
Fig.17 Outline.
handbook, full pagewidth
seating plane
hole Ø1.3 mm
for Ødt = 0.8 mm
l
Ødt
0 ≤ α < 50°
P
h
lt
α
A
CBA101
b
1997 Nov 17 25
Philips Components Product specification
Metallized polyester film capacitors MKT 468
URdc = 100 V; URac =63V loose and taped
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 468 ..... AND PACKAGING
LOOSE IN BOX; lt= 3.5 ±0.5 mm REEL
last 5 digits of
catalogue number(1) SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 15.0 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
1.2 5.5 ×14.5 ×17.5 0.8 04125 05125 2000 1100
1.5 6.0 ×15.0 ×17.5 0.9 04155 05155 2000 1000
1.8 6.5 ×15.5 ×17.5 1.2 04185 05185 1500 900
2.2 7.0 ×16.0 ×17.5 1.3 04225 05225 1250 800
2.7 8.0 ×17.0 ×17.5 1.5 04275 05275 1000 750
3.3 8.5 ×17.5 ×17.5 1.7 04335 05335 1000 700
Pitch = 22.5 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
3.9 6.5 ×18.5 ×26.0 2.1 04395 05395 1000 650
4.7 7.0 ×19.5 ×26.0 3.2 04475 05475 900 550
5.6 7.5 ×20.0 ×26.0 3.8 04565 05565 750 500
6.8 8.5 ×21.0 ×26.0 3.9 04685 05685 750 450
8.2 9.5 ×21.5 ×26.0 4.0 04825 05825 700 400
10.0 10.5 ×22.5 ×26.0 4.5 04106 05106 500 350
1997 Nov 17 26
Philips Components Product specification
Metallized polyester film capacitors MKT 468
MKT 468 GENERAL DATA PITCH 15/22.5/27.5 mm (kinked leads)
Specific reference data for the 250 V DC capacitors
Available 250 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.47 µF≤75 ×10−4≤120 ×10−4≤225 ×10−4
C>0.47 µF≤75 ×10−4≤120 ×10−4−
Rated voltage pulse slope (dU/dt)R at URdc:
lmax = 17.5 mm 45 V/µs
lmax = 26.0 mm 20 V/µs
lmax = 30.0 mm 15 V/µs
RC between leads, for C >0.33 µF >10000 s
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 468 16... preferred
±5% 2222 468 17... preferred
Taped on reel H = 16.0 mm; note 1 ±10% 2222 468 18... on request
±5% 2222 468 19... on request
Fig.18 Outline.
handbook, full pagewidth
seating plane
hole Ø1.3 mm
for Ødt = 0.8 mm
l
Ødt
0 ≤ α < 50°
P
h
lt
α
A
CBA101
b
1997 Nov 17 27
Philips Components Product specification
Metallized polyester film capacitors MKT 468
URdc = 250 V; URac = 160 V loose and taped
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 468 ..... AND PACKAGING
LOOSE IN BOX; lt= 3.5 ±0.5 mm REEL
last 5 digits of
catalogue number(1) SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 15.0 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
0.27 5.0 ×14.0 ×17.5 0.8 16274 17274 2000 1200
0.33 5.5 ×14.5 ×17.5 0.9 16334 17334 2000 1100
0.39 6.0 ×15.0 ×17.5 0.9 16394 17394 2000 1000
0.47 6.5 ×15.0 ×17.5 1.1 16474 17474 1500 900
0.56 7.5 ×15.5 ×17.5 1.3 16564 17564 1250 800
0.68 8.0 ×16.5 ×17.5 1.4 16684 17684 1000 750
0.82 8.5 ×17.0 ×17.5 1.5 16824 17824 1000 700
1.0 8.0 ×19.5 ×17.5 1.7 16105 17105 1000 750
Pitch = 22.5 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
1.2 7.0 ×19.0 ×26.0 3.1 16125 17125 1000 550
1.5 8.0 ×19.5 ×26.0 3.6 16155 17155 750 500
1.8 8.5 ×20.5 ×26.0 3.9 16185 17185 750 450
2.2 9.5 ×21.0 ×26.0 4.1 16225 17225 750 400
2.7 11.0 ×24.0 ×26.0 4.3 16275 17275 500 350
3.3 12.0 ×25.5 ×26.0 4.5 16335 17335 500 350
3.9 13.5 ×26.5 ×26.0 6.4 16395 17395 400 300
4.7 14.5 ×27.5 ×26.0 7.4 16475 17475 250 250
Pitch = 27.5 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
5.6 15.0 ×27.5 ×30.0 9.1 16565 17565 300 350
1997 Nov 17 28
Philips Components Product specification
Metallized polyester film capacitors MKT 468
MKT 468 GENERAL DATA PITCH 15/22.5/27.5 mm (kinked leads)
Specific reference data for the 400 V DC capacitors
Available 400 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
0.12 <C≤0.47 µF≤75 ×10−4≤120 ×10−4≤225 ×10−4
C>0.47 µF≤75 ×10−4≤120 ×10−4−
Rated voltage pulse slope (dU/dt)R at URdc:
lmax = 17.5 mm 65 V/µs
lmax = 26.0 mm 30 V/µs
lmax = 30.0 mm 25 V/µs
R between leads, for C ≤0.33 µF >30000 MΩ
RC between leads, for C >0.33 µF >10000 s
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 468 28... preferred
±5% 2222 468 29... preferred
Taped on reel H = 16.0 mm; note 1 ±10% 2222 468 30... on request
±5% 2222 468 31... on request
Fig.19 Outline.
handbook, full pagewidth
seating plane
hole Ø1.3 mm
for Ødt = 0.8 mm
l
Ødt
0 ≤ α < 50°
P
h
lt
α
A
CBA101
b
1997 Nov 17 29
Philips Components Product specification
Metallized polyester film capacitors MKT 468
URdc = 400 V; URac = 200 V loose and taped
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 468 ..... AND PACKAGING
LOOSE IN BOX; lt= 3.5 ±0.5 mm REEL
last 5 digits of
catalogue number(1) SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 15.0 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
0.12 5.0 ×14.0 ×17.5 0.6 28124 29124 2000 1200
0.15 6.0 ×14.0 ×17.5 0.8 28154 29154 1750 1100
0.18 6.5 ×14.5 ×17.5 0.9 28184 29184 1500 900
0.22 7.0 ×15.0 ×17.5 1.1 28224 29224 1500 800
0.27 7.5 ×16.0 ×17.5 1.4 28274 29274 1250 800
0.33 8.5 ×16.5 ×17.5 1.5 28334 29334 1000 700
0.39 7.5 ×19.0 ×17.5 1.5 28394 29394 1000 800
0.47 8.5 ×20.0 ×17.5 1.7 28474 29474 750 700
Pitch = 22.5 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
0.56 7.0 ×19.0 ×26.0 3.1 28564 29564 1000 550
0.68 8.0 ×19.5 ×26.0 3.6 28684 29684 750 500
0.82 8.5 ×20.5 ×26.0 3.9 28824 29824 750 450
1.0 9.5 ×21.0 ×26.0 4.0 28105 29105 750 400
1.2 11.0 ×24.0 ×26.0 4.6 28125 29125 500 350
Pitch = 27.5 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
1.5 11.0 ×24.5 ×30.0 6.7 28155 29155 450 350
1.8 12.5 ×25.5 ×30.0 7.6 28185 29185 350 300
2.2 14.0 ×26.5 ×30.0 9.0 28225 29225 300 300
1997 Nov 17 30
Philips Components Product specification
Metallized polyester film capacitors MKT 468
MKT 468 GENERAL DATA PITCH 15/22.5/27.5 mm (kinked leads)
Specific reference data for the 630 V DC capacitors
Available 630 V DC versions
Note
1. H = in-tape height; for detailed specifications refer to this handbook, Chapter
“Packaging”
.
DESCRIPTION VALUE
at 1 kHz at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.1 µF≤75 ×10−4≤120 ×10−4≤200 ×10−4
0.1 µF<C≤0.47 µF≤75 ×10−4≤120 ×10−4≤225 ×10−4
C>0.47 µF≤75 ×10−4≤120 ×10−4−
Rated voltage pulse slope (dU/dt)R at URdc:
lmax = 17.5 mm 90 V/µs
lmax = 26.0 mm 35 V/µs
lmax = 30.0 mm 30 V/µs
R between leads, for C ≤0.33 µF >30000 MΩ
RC between leads, for C >0.33 µF >10000 s
PACKAGING DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt= 3.5 ±0.5 mm ±10% 2222 468 40... preferred
±5% 2222 468 41... preferred
Taped on reel H = 16.0 mm; note 1 ±10% 2222 468 42... on request
±5% 2222 468 43... on request
Fig.20 Outline.
handbook, full pagewidth
seating plane
hole Ø1.0 mm
for Ødt = 0.6 mm
l
Ødt
0 ≤ α < 50°
P
h
lt
α
A
CBA100
b
1997 Nov 17 31
Philips Components Product specification
Metallized polyester film capacitors MKT 468
URdc = 630 V; URac = 250 V loose and taped
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER 2222 468 ..... AND PACKAGING
LOOSE IN BOX; lt= 3.5 ±0.5 mm REEL
last 5 digits of
catalogue number(1) SPQ SPQ
C-tol = ±10% C-tol = ±5%
Pitch = 15.0 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
0.039 5.0 ×13.5 ×17.5 0.7 40393 41393 2000 1200
0.047 5.5 ×14.0 ×17.5 0.7 40473 41473 2000 1100
0.056 6.0 ×14.0 ×17.5 0.9 40563 41563 1750 1000
0.068 7.0 ×14.5 ×17.5 1.1 40683 41683 1500 800
0.082 7.5 ×15.0 ×17.5 1.3 40823 41823 1500 800
0.1 8.0 ×15.5 ×17.5 1.5 40104 41104 1250 750
0.12 7.5 ×18.0 ×17.5 1.7 40124 41124 1250 800
0.15 8.5 ×19.0 ×17.5 2.0 40154 41154 1000 700
Pitch = 22.5 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
0.18 7.0 ×18.0 ×26.0 2.9 40184 41184 1000 550
0.22 8.0 ×19.0 ×26.0 3.5 40224 41224 750 500
0.27 9.0 ×19.5 ×26.0 3.7 40274 41274 750 450
0.33 10.0 ×20.5 ×26.0 4.3 40334 41334 700 400
0.39 11.0 ×23.0 ×26.0 4.9 40394 41394 600 350
0.47 12.0 ×24.0 ×26.0 5.7 40474 41474 500 350
0.56 13.5 ×25.0 ×26.0 6.7 40564 41564 450 300
0.68 15.0 ×25.5 ×26.0 7.6 40684 41684 400 250
Pitch = 27.5 ±0.4 mm; dt= 0.80 ±0.08 mm; A = 2.5 +1.4/−0.5 mm
0.82 15.0 ×26.0 ×30.0 7.8 40824 41824 300 250
1997 Nov 17 32
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
CONSTRUCTION
Description
•Low-inductive wound cell of metallized polyethylene
terephthalate film
•Protected by a hard, water repellent, solvent resistant
epoxy lacquer
•Radial leads, solder coated:
– Copper clad steel wire (Imax = 7.3 mm)
– Copper wire (Imax > 7.3 mm).
Fig.21 Construction.
handbook, halfpage
connecting wire
metallized polyester film
metal spray layer
CBA073
Mounting
NORMAL USE
The capacitors are designed for mounting on
printed-circuit boards. The capacitors packed in bandoliers
are designed for mounting on printed-circuit boards by
means of automatic insertion machines.
For detailed tape specifications refer to this handbook,
Chapter
“Packaging”
.
SPECIFIC METHOD OF MOUNTING TO WITHSTAND VIBRATION
AND SHOCK
In order to withstand vibration and shock tests, it must be
ensured that the underside of the crimps are in good
contact with the printed-circuit board:
•For pitches of 15 mm capacitors shall be mechanically
fixed by the leads.
•For larger pitches the capacitors shall be mounted in the
same way and the body clamped.
RATINGS AND CHARACTERISTICS
Unless otherwise specified, all electrical values apply to an
ambient free air temperature of 23 ±1°C, an atmospheric
pressure of 86 to 106 kPa and a relative humidity of
50 ±2%.
For reference testing, a conditioning period shall be
applied over 96 ±4 hours by heating the products in a
circulating air oven at the rated temperature and a relative
humidity not exceeding 20%.
1997 Nov 17 33
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Capacitance
All capacitance values are specified at 1 kHz.
Fig.22 Capacitance change as a function of frequency: typical curve.
handbook, full pagewidth
CBA074
−3
2
102103104105
−2
−1
0
f (Hz)
1
∆C
C
(%)
Fig.23 Capacitance as a function of ambient free air temperature, measured at 1 kHz, 1 V: typical curves.
handbook, full pagewidth
CBA102
100
2
-2
-4
-60 -20 60
0
20 Tamb (°C)
∆C/C
(%)
100V
250V
400 - 630V
1997 Nov 17 34
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Impedance
Temperature
•Storage temperature: Tstg =−25 to +40 °C with RH maximum 80% and without condensation.
Voltage
•Category voltage: Uc= 0.8 ×URdc
•Test voltage between leads: 1.6 ×URdc
•Test voltage between interconnected leads and case (foil method): 2 ×URdc (min. 200 V).
Fig.24 Impedance as a function of frequency: typical curve.
handbook, full pagewidth
108
CBA103
107
106
105
104
102
10-3
10-2
10-1
100
101
f (Hz)
Impedance
(Ω)
100V; 100 nF
MKT 465
1997 Nov 17 35
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Maximum RMS voltage (sinewave) as a function of frequency for Tamb ≤85 °C
Fig.25 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 100 V.
handbook, full pagewidth
AC voltage
(V)
f (Hz) 106
CBA104
105
104
103
102
102
100
101
MKT 465/466/467/468
10 nF (lmax = 7.5 mm)
1.5 µF (lmax = 17.5 mm)
3.9 µF (lmax = 26.0 mm)
10 µF (lmax = 26.0 mm)
470 nF (lmax = 10.0 mm)
1 µF (lmax = 12.5 mm)
Fig.26 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 250 V.
handbook, full pagewidth
CBA105
105106
104
103
102
101
103
100
102
101
f (Hz)
AC voltage
(V)
10 nF (lmax = 10.0 mm)
100 nF (lmax = 10.0 mm)
220 nF (lmax = 12.5 mm)
2.2 µF (lmax = 26.0 mm)
5.6 µF (lmax = 30.0 mm)
1997 Nov 17 36
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Fig.27 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 400 V.
handbook, full pagewidth
CBA106
105106
104
103
102
101
103
100
102
101
f (Hz)
AC voltage
(V)
10 nF (lmax = 10.0 mm)
100 nF (lmax = 12.5 mm)
220 nF (lmax = 17.5 mm)
1.0 µF (lmax = 26.0 mm)
2.2 µF (lmax = 30.0 mm)
Fig.28 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 630 V.
handbook, full pagewidth
CBA107
105106
104
103
102
101
103
100
102
101
f (Hz)
AC voltage
(V)
10 nF (lmax = 12.5 mm)
100 nF (lmax = 17.5 mm)
220 nF (lmax = 26.0 mm)
470 nF (lmax = 26.0 mm)
820 nF (lmax = 30.0 mm)
1997 Nov 17 37
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Maximum RMS voltage (sinewave) as a function of frequency for Tamb >85 °C
The maximum RMS voltage in Figs 25 to 28 has to be multiplied by a factor given in Fig.29.
The power dissipation has to be checked, and must not exceed the maximum allowed power shown in Figs 36 and 37.
Fig.29 Multiplying factor as a function of temperature.
handbook, full pagewidth
100
1.2
0.8
0.4
0
1.0
0.6
0.2
−60 −40 −20 0 20 40 60 80
CBA086
factor
Tamb (°C)
1997 Nov 17 38
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Maximum RMS current (sinewave) as a function of frequency for Tamb ≤85 °C
Fig.30 AC current (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 100 V.
handbook, full pagewidth
CBA581
105106
104
103
102
101
104
10-1
101
100
103
102
AC current
(mA)
f (Hz)
470 nF
10 nF
1.0 µF
1.5 µF
3.9 µF
10 µF
Fig.31 AC current (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 250 V.
handbook, full pagewidth
CBA582
105106
104
103
102
101
104
10-1
101
100
103
102
AC current
(mA)
f (Hz)
100 nF
10 nF
1.0 µF
2.2 µF
5.6µF
220 nF
1997 Nov 17 39
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Fig.32 AC current (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 400 V.
handbook, full pagewidth
CBA583
105106
104
103
102
101
104
10-1
101
100
103
102
AC current
(mA)
f (Hz)
100 nF
10 nF
1.0 µF
2.2 µF
220 nF
Fig.33 AC current (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 630 V.
handbook, full pagewidth
CBA584
105106
104
103
102
101
104
10-1
101
100
103
102
AC current
(mA)
f (Hz)
100 nF
10 nF
1.0 µF
220 nF
1997 Nov 17 40
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Tangent of loss angle
Rated voltage pulse slope (dU/dt)R
Notes
1. The maximum pulse load values are valid for voltages equal to the rated voltage. For lower voltages the given values
may be multiplied by URdc and divided by the applied voltage.
2. If the pulse requirement is satisfied, a check must be made to ensure that the maximum dissipation is not exceeded.
CAPACITANCE TANGENT OF LOSS ANGLE
at 1 kHz at 10 kHz at 100 kHz
C≤0.1 µF≤75 ×10−4≤120 ×10−4≤200 ×10−4
0.1 µF<C≤0.47 µF≤75 ×10−4≤120 ×10−4≤225 ×10−4
0.47 µF<C≤1µF≤75 ×10−4≤120 ×10−4−
C>10 µF≤75 ×10−4≤120 ×10−4−
RATED
VOLTAGE
UR (V)
MAXIMUM RATED PULSE LOAD (V/µs) AS A FUNCTION OF lmax(1)(2)
lmax = 7.5 mm lmax = 10.0 mm lmax = 12.5 mm lmax = 17.5 mm lmax = 26.0 mm lmax = 30.0 mm
100 120 40 30 20 10 −
250 −120 120 45 20 15
400 −170 170 65 30 25
630 −− 90 90 35 30
Fig.34 Tangent of loss angle as a function of frequency: typical curve.
handbook, full pagewidth
CBA087
105
104
103
102
103
101
102
dissipation
factor
(x 10-4)
f (Hz)
1997 Nov 17 41
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Insulation resistance
The insulation resistance is measured after a voltage has been applied for 1 minute ±5 seconds, the voltage being
100 ±15 V for the 100, 250 and 400 V versions and 500 ±50 V for the 630 V versions:
•Resistance between leads, for C ≤0.33 µF:
– 100 V versions: >15000 MΩ
– 250, 400 and 630 V versions: >30000 MΩ
•RC between leads, for C >0.33 µF:
– 100 V versions: >5000 s
– 250, 400 and 630 V versions: >10000 s
•Resistance between interconnected leads and case (foil method): >30000 MΩ.
Fig.35 RC product as a function of ambient free air temperature: typical curve.
handbook, full pagewidth
CBA088
100-50 0 50
105
102
104
103
RC
(s)
Tamb (°C)
1997 Nov 17 42
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Maximum dissipation
Power dissipation curves as a function of capacitor
body length and thickness (see Figs 36 and 37)
bmax
(mm)
lmax
(mm)
7.3 10.0 12.5 17.5 26.0 30.0
3.5 1 5 −−−−
426 79−−
4.5 3 6 8 10 −−
5 4 7 9 10 15 16
5.5 5 7 10 11 16 17
6 6 8 10111617
6.5 −9 11121718
7−−−12 17 18
7.5 −−−13 18 19
8−−−13 18 20
8.5 −−−14 19 20
9−−−14 19 21
9.5 −−−15 20 21
10 −−−15 20 22
10.5 −−−−21 23
11 −−−−21 23
11.5 −−−−22 24
12 −−−−23 24
12.5 −−−−23 26
13 −−−−24 26
13.5 −−−−24 26
14 −−−−28 26
14.5 −−−−26 27
15 −−−−−27
15.5 −−−−−28
16 −−−−−28
Fig.36 Maximum permissible power dissipation
as a function of ambient temperature, at
various capacitor dimensions.
4
columns
0 100
250
0
50
CBA089
100
150
200
20 40 8060
Pmax
(mW)
Tamb (°C)
78
9
10
11
34
56
12
13
14
15
16
17
12
Fig.37 Maximum permissible power dissipation
as a function of ambient temperature, at
various capacitor dimensions.
4
columns
Pmax
(mW)
Tamb (°C)
CBA090
0 100
750
250
0
500
20 40 60 80
22
19
24 23
18
25
26
27
28
21
20
1997 Nov 17 43
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Application note
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (Up) shall not be greater than the rated DC voltage (URdc).
2. The peak-to-peak voltage (Up-p) shall not be greater than times the rated AC voltage (URac) to avoid the
ionisation inception level.
3. The peak current (Ip) shall not exceed the maximum peak current, defined as maximum voltage pulse slope (dU/dt)
multiplied by the capacitance:
Or the voltage pulse slope shall not exceed the rated voltage pulse slope. If the pulse voltage is lower than the rated
voltage, the values (see Section “Rated voltage pulse slope (dU/dt)R” for more details) may be multiplied by URdc
and divided by the applied voltage.
4. The dissipated power shall not be greater than the maximum permissible power dissipation shown in Figs 36 and 37.
5. The free air ambient temperature for the capacitor does not exceed the category temperature.
6. Since all metallized polyethylene terephthalate film capacitors have an intrinsically active flammability risk after a
capacitor breakdown (short circuit), it is recommended that for MKT styles the power to the component is limited to
10 times the maximum allowed power dissipation (Pmax) during the short circuit failure mode of the capacitor.
22×
I
p
max C dU
dt
--------
max=
1997 Nov 17 44
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
MARKING
Product marking
CAPACITORS WITH A BODY LENGTH =7.5 mm
The capacitors are marked on the top in black ink with the
following information:
1. Capacitance code in accordance with
“IEC 62”
2. Tolerance on rated capacitance: K = ±10%; J = ±5%
3. Rated voltage (DC).
Fig.38 Example of marking for a capacitor with
a body length =7.5 mm.
handbook, halfpage
47n
K 100
CBA108
CAPACITORS WITH A BODY LENGTH OF 10.0 OR 12.5 mm
The capacitors are marked on the top in black ink with the
following information:
1. Capacitance code in accordance with
“IEC 62”
2. Tolerance on rated capacitance: K = ±10%; J = ±5%
3. Rated voltage (DC).
Fig.39 Example of marking for a capacitor with
a body length of 10.0 or 12.5 mm.
handbook, halfpage
470n K 100
CBA109
CAPACITORS WITH A BODY LENGTH ≥12.5 mm
The capacitors are marked on the top in black ink with the
following information:
1. Manufacturer’s symbol
2. Capacitance code in accordance with
“IEC 62”
3. Tolerance on rated capacitance: K = ±10%; J = ±5%
4. Rated voltage (DC).
Fig.40 Example of marking for a capacitor with
a body length ≥12.5 mm.
handbook, halfpage
PHILIPS 820n J 100
CBA110
1997 Nov 17 45
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
Package marking
The package containing the capacitors is marked as shown in Fig.41.
handbook, full pagewidth
CCA338
1.
2.
3.
4.
5.
8.
7.
6.
9.
10.
Fig.41 Barcode label.
Barcode label marking
LINE MARKING EXPLANATION
1 Manufacturer's name
2 Country of origin
3 Sub-family
4 Type description
5 Capacitance value, tolerance, voltage
and climatic category
(“IEC 68-1”)
6−
7 Preference origin code: A
Country of origin in code: 170 (Belgium)
Responsible production centre: HQ
Work order: WO
8 Product type description
9 Quantity and production period, year and
week code
10 Product code (12NC)
1997 Nov 17 46
Philips Components Product specification
Metallized polyester film capacitors MKT 465/466/467/468
QUICK REFERENCE TEST REQUIREMENTS (see note 1)
Notes
1. For detailed information, see
“Type specification”
.
2. Measuring frequency 10 kHz.
TEST PROCEDURE
(quick reference) REQUIREMENTS
Robustness of leads
Tensile and bending:
“IEC 68-2-21”
no visible damage
legible marking
∆C/C≤2%
∆tan δ≤30 ×10−4; note 2
Resistance to soldering heat
“IEC 68-2-20”
solder bath: 260 °C; 10 s
Resistance to solvents isopropyl alcohol; 23 °C; 5 minutes
Robustness of component
Vibration:
“IEC 68-2-6”
10 to 55 Hz; amplitude 0.75 mm or
acceleration 98 m/s2; 6 hours ∆C/C≤3%
∆tan δ≤30 ×10−4; note 2
Shock:
“IEC 68-2-27”
half sinewave; 490 m/s2; 11 ms
Climatic sequence
Dry heat:
“IEC 68-2-2”
16 hours; 100 °C∆C/C≤5%
∆tan δ≤50 ×10−4; note 2
Rins ≥50% of specified value
Damp heat cyclic, test Db, first cycle:
“IEC 68-2-30”
Cold:
“IEC 68-2-1”
2 hours; −55 °C
Damp heat cyclic, test Db,
remaining cycles:
“IEC 68-2-30”
Other applicable tests
Damp heat, steady state:
“IEC 68-2-3”
56 days; 40 °C; 90 to 95% RH ∆C/C≤5%
∆tan δ≤50 ×10−4; note 2
Rins ≥50% of specified value
Endurance (DC):
“IEC 384-2”
2000 hours:
1.25 ×URdc; 85 °C
1.25 ×UCdc; 100 °C
∆C/C≤5%
∆tan δ≤30 ×10−4; note 2
Rins ≥50% of specified value
Heat storage:
“IEC 384-2”
2000 hours; 100 °C∆C/C≤3%
∆tan δ≤30 ×10−4; note 2
Resistance to soldering heat
with preheating:
“IEC 384-2”
body temperature: 100 °C;
bath temperature: 260 °C;
dwell time: 10 s
∆C/C≤2% (C ≤10 nF)
∆C/C≤1% (C >10 nF)
∆tan δ≤30 ×10−4; note 2
