Finisar Corpor ation July 2015 Rev. B Page 1
Product Specification
2 Gb/s RoHS Compliant Long-Wavelength Pluggable SFP Transceiver
FTLF1419P1xCL
PRODUCT FEATURES
• Up to 2.125Gb/s bi-directional
data links
• Hot-pluggable SFP footprint
• Built-in digital diagnostic functions
• Uncooled 1310nm DFB laser
transmitter
• Duplex LC connector
• RoHS compliant and Lead Free
• No Rate Select input required for
Fibre Channel 1x/2x Operation
• Up to 55 km on 9/125µm SMF
• Metal enclosure, for lower EMI
• Single 3.3V power supply
• Low power dissipation <700mW
typical
• Extended operating temperature
range: -10°C to 70°C
APPLICATIONS
• 1.25Gb/s 1000Base-LX Ethernet
• Dual Rate 1.06 / 2.125 Gb/s Fibre
Channel
Finisar’s FTLF1419P1xCL Small Form Factor Pluggable (SFP) transceivers are
compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1.
They simultaneously comply with Gigabit Ethernet as specified in IEEE Std 802.32, and
1x and 2x Fibre Channel as defined in FC-PI 13.03,4. The optical transceivers are
compliant per the RoHS Directive 2011/65/EU. See Finisar Application Note AN-2038
for more details. Digital diagnostics functions are available via the 2-wire serial bus
specified in the SFP MSA.
PRODUCT SELECTION FTLF1419P1xCL
x
W
Wide Extraction Bail
B
Narrow Extraction Bail
FTLF1419P1xCL Pluggable SFP Product Specification
Finisar Corpor ation July 2015 Rev. B Page 2
I. Pin Descriptions
Pin
Symbol
Name/Description
Ref.
1
VEET
Transmitte r Ground (Common with Rec eiver Ground )
1
2
TFAULT
Transmitter Fa ult. Not supported.
3
TDIS
Transmitter Disable. Laser output disabled on high or open.
2
4
MOD_DEF(2)
Module Defi nition 2. Data line for Se rial ID.
3
5
MOD_DEF(1)
Module Defi nition 1. Clock line for Serial ID.
3
6
MOD_DEF(0)
Module Definition 0. G rounded within the module.
3
7
Rate Select
No connection required
4
8
LOS
Loss of Signal ind ica tion. Logic 0 indic a tes normal opera tion.
5
9
VEER
Receiver Ground (Common with Trans mi tter Ground)
1
10
VEER
Receiver Ground (Common with Transmitter Ground)
1
11
VEER
Receiver Ground (Common with Transmitter Ground)
1
12
RD-
Receiver Inverted DATA out. AC Coupled
13
RD+
Receiver Non-inverted DATA out. AC Coupled
14
VEER
Receiver Ground (Common with Transmitter Ground)
1
15
VCCR
Receiver Power Supply
16
VCCT
Transmitter Power Supply
17
VEET
Transmitte r Ground (Common with Rec eiver Ground )
1
18
TD+
Transmitter Non-Inverted DATA in. AC Coupled.
19
TD-
Transmitter In ver te d DATA in. AC Co up led.
20
VEET
Transmitte r Ground (Common with Rec eiver Ground )
1
Notes:
1. Circuit ground is in te rnally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0V and 3.6V.
MOD_DEF( 0) pulls line low to indic a te module is plugged i n.
4. Finisar FTLFxx21xxxxx transceivers operate between OC-3 a nd OC-48, 1x and 2x Fibre Channel, and
Gigabit Ether net data rates and r e sp e c tive protocols without active control. Finisar FTLFxx19xxxxx
transceivers operate at 1x and 2x Fibre Channel, and Gigabit Ethernet data rates and respective
proto c ols witho ut active control.
5. LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage
between 2.0V and 3.6V. Logic 0 indicates normal operation ; logic 1 indicates loss o f si gnal.
VeeT
VeeT
VeeR
VeeR
TD-
TD+
RD+
RD-
VccT
VccR
VeeT
VeeR
TXFault
MOD-DEF(2)
MOD-DEF(1)
MOD-DEF(0)
Rate Select
LOS
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
Towards
ASIC
Towards
Bezel
TX Disable
VeeR
Pinout of Connector Block on Host Board
FTLF1419P1xCL Pluggable SFP Product Spe c ification
Finisar Corpor ation July 2015 Rev. B Page 3
II. Absolute Maximum Ratings
Symbol
Min
Typ
Max
Unit
Ref.
Vcc
-0.5
4.5
V
TS
-40
85
°C
TOP
-10
70
°C
RH
0
85
%
1
III. Electrical Characteristics (TOP = -10 to 70
°
C, VCC = 3.00 to 3.60 Volts)
Symbol
Min
Typ
Max
Unit
Ref.
Vcc
3.00
3.60
V
Icc
200
300
mA
Transmitter
Rin
100
Ω
2
Vin,pp
250
1200
mV
VD
Vcc – 1.3
Vcc
V
VEN
Vee
Vee+ 0.8
V
3
10
us
Receiver
Vout,pp
300
400
800
mV
4
tr
100
175
ps
5
tf
100
175
ps
5
VLOS fault
Vcc – 0.5
VccHOST
V
6
VLOS norm
Vee
Vee+0.5
V
6
PSR
100
mVpp
7
RX
∆
DJ
51.7
ps
8
RX
∆
TJ
122.4
ps
Notes:
1. Non condensing.
2. Connected directly to TX data input pins. AC coupled thereafter.
3. Or open circ uit.
4. Into 100 ohm differential termination.
5. 20 – 80 %
6. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no sig nal detected.
7. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to
specified value applied through the recommended power supply filtering network.
8. Measured with DJ-free data input si gnal. I n actual application, output DJ will be the sum o f input D J
and
∆
DJ.
FTLF1419P1xCL Pluggable SFP Product Spe c ification
Finisar Corpor ation July 2015 Rev. B Page 4
IV. Optical Characteristics (TOP = -10 to 70
°
C, VCC = 3.00 to 3.60 Volts)
Symbol
Min
Typ
Max
Unit
Ref.
Transmitter
POUT
0
5
dBm
1
λ
1275
1350
nm
2
σ
1
nm
2
OMA
174
µW
2,3
SSR
30
dB
tr/ tf
160
ps
4
RIN
-120
dB/Hz
ER
9
dB
TX
∆
DJ
56.5
ps
5
TX
∆
TJ
119
ps
Receiver
R
SENS1
-21
dBm
6, 7
R
SENS2
-22
dBm
6, 7
R
SENS1
-22
dBm
6, 7
PMAX
0
dBm
1500
MHz
λC
1270
1600
nm
12
dB
LOSD
-23
-19
dBm
LOSA
-30
-25
dBm
0.5
dB
Notes:
1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.
2. Meets curves in FC-PI 13.0 Figures 18 and 19, which allow trade-off between wavelength, spectral
wid th a n d OMA.
3. Equivalent e xtinction ratio spe c ification for Fibre C han nel. Allows smaller ER at higher average
power.
4. Unfiltered, 20-80%. Complies with FC 1x and 2x eye mask when filtered.
5. Measured with DJ-free data input signal. In actual app lic a tion, output DJ will be the sum of inp ut DJ
and
∆
DJ.
6. Measured with conformance signals defined in FC-PI 13.0 specifications.
7. As measured with 9dB extinction ratio. Measured with a PRBS 27-1 test pattern.
FTLF1419P1xCL Pluggable SFP Product Spe c ification
Finisar Corpor ation July 2015 Rev. B Page 5
V. General Specifications
Parameter
Symbol
Min
Typ
Max
Units
Ref.
Data Rate
BR
1062
2125
Mb/sec
1
Bit Error Rate
BER
10-12
2
Max. S upported Link Length o n
9/125
µ
m SMF @ 2X Fibre Channel
L
MAX1
52.5
km
3, 4
Max. Supported Link Le ngt h o n
9/125µm SMF @ Gigabit Ethernet
L
MAX2
55
km
3, 4
Notes:
1. Gigabit Et hernet and 1x/ 2x Fibre Channel compliant.
2. Tested wit h a PRBS 27-1 test pa ttern.
3. Dispersion limited per FC-PI Rev. 13
4. Attenuation of 0.40 dB/km is used for the link length calcula tions. Distances are indicative onl y.
Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on
specific conditions in your application.
VI. Environmental Specifications
Finisar 1310nm SFP transceivers have an extended operating temperature range from
–10°C to +70°C case temperature.
Parameter
Symbol
Min
Typ
Max
Units
Ref.
Case Operating Temperature
T
op
-10
70
°C
Storage Temperature
T
sto
-40
85
°C
VII. Regulatory Compliance
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations.
These products are certified by TÜV and CSA to meet the Class 1 eye safety
requirements of EN (IEC) 60825 and the electrical safety requirements of
EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.
FTLF1419P1xCL Pluggable SFP Product Spe c ification
Finisar Corpor ation July 2015 Rev. B Page 6
VIII. Digital Diagnostic Functions
Finisar FTLF1419P1xCL SFP transceivers support the 2-wire serial communication
protocol as defined in the SFP MSA3.
The standard SFP serial ID provides access to identification information that describes
the transceiver’s capabilities, standard interfaces, manufacturer, and other information.
Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic
monitoring interface, which allows real-time access to device operating parameters such
as transceiver temperature, laser bias current, transmitted optical power, received optical
power and transceiver supply voltage. It also defines a sophisticated system of alarm and
warning flags, which alerts end-users when particular operating parameters are outside of
a factory set normal range.
The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a
2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic
monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally
defined serial ID memory map remains unchanged. The interface is identical to, and is
thus fully backward compatible with both the GBIC Specification and the SFP Multi
Source Agreement. The complete interface is described in Finisar Application Note AN-
2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed
through a 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the
SFP transceiver into those segments of the E2PROM that are not write-protected. The
negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod
Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with
SCL to mark the start and end of serial protocol activation. The memories are organized
as a series of 8-bit data words that can be addressed individually or sequentially.
For more information, please see the SFP MSA documentation3 or Finisar Application
Note AN-2030.
Digital diagnostics for the FTLF1419P1xCL are externally calibrated by default.
Please note that evaluation board FDB-1018 is available with Finisar ModDEMO
software that allows simple to use communication over the 2-wire serial interface.
FTLF1419P1xCL Pluggable SFP Product Spe c ification
Finisar Corpor ation July 2015 Rev. B Page 7
IX. Mechanical Specifications
Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the
dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3.
FTLF1419P1BCL
FTLF1419P1xCL Pluggable SFP Product Spe c ification
Finisar Corpor ation July 2015 Rev. B Page 8
FTLF1419P1WCL
FTLF1419P1xCL Pluggable SFP Product Spe c ification
Finisar Corpor ation July 2015 Rev. B Page 9
X. PCB Layout and Bezel Recommendations
FTLF1419P1xCL Pluggable SFP Product Spe c ification
Finisar Corpor ation July 2015 Rev. B Page 10
FTLF1419P1xCL Pluggable SFP Product Spe c ification
Finisar Corpor ation July 2015 Rev. B Page 11
XI. References
1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA),
September 2000. Documentation is currently available at Finisar upon request.
2. IEEE Std 802.3. IEEE Standards Department, 2002.
3. “Fibre Channel Draft Physical Interface Specification (FC-PI 13.0)”. American
National Standard for Information Systems.(*)
4. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”.
American National Standard for Information Systems.
5. Directive 2011/65/EU of the European Council Parliament and of the Council,
“on the restriction of the use of certain hazardous substances in electrical and
electron ic eq ui pm ent ”. Certain products may use one or more exemptions as
allowed by the Directive.
(*) FC-PI 13.0 does not specify a 1310nm DFB interface for extended reach
applications. The FTLF1419P1xCL complies with this standard, except for the optical
output power. See section IV for details.
XII. For More Information
Finisar Corporation
1389 Moffett Park Drive
Sunnyvale, CA 94089-1133
Tel. 1-408-548-1000
Fax 1-408-541-6138
sales@finisar.com
www.finisar.com