SPLFA-2
SPLFA30F
AC-DC Power Supplies Open Frame/Enclosed Value-added Type
SPLF A 30 F -O -O
Ordering information
1 2 3 4 5 6
1 Series name
2 Single output
3 Output wattage
4 Universal input
5 Output voltage
6 Optional
C
: with Coating
MODEL SPLFA30F-5 SPLFA30F-12 SPLFA30F-24
MAX OUTPUT WATTAGE[W] 30.0 30.0 31.2
DC OUTPUT 5V 6A 12V 2.5A 24V 1.3A
SPECIFICATIONS
MODEL SPLFA30F-5 SPLFA30F-12 SPLFA30F-24
INPUT
VOLTAGE[V] AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.1)
*3
CURRENT[A]
ACIN 100V
0.65typ (Io=100%)
ACIN 200V
0.35typ (Io=100%)
FREQUENCY[Hz] 50 / 60 (47 - 440)
EFFICIENCY[%]
ACIN 100V
75.0typ 78.0typ 81.0typ
ACIN 200V
77.0typ 80.0typ 83.0typ
INRUSH CURRENT[A]
ACIN 100V
15typ (Io=100%) (At cold start) (Ta=25C)
ACIN 200V
30typ (Io=100%) (At cold start) (Ta=25C)
LEAKAGE CURRENT[mA] 0.30 / 0.65max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
OUTPUT
VOLTAGE[V] 51224
CURRENT[A] 6.0 2.5 1.3
LINE REGULATION[mV]
*5
20max 48max 96max
LOAD REGULATION[mV]
*5
100max 100max 150max
RIPPLE[mVp-p]
0 to +50C
*1
100max 120max 120max
-10 - 0C
*1
140max 160max 160max
RIPPLE NOISE[mVp-p]
0 to +50C
*1
250max 250max 250max
-10 - 0C
*1
300max 300max 300max
TEMPERATURE REGULATION[mV]
0 to +50C
50max 120max 240max
-10 to +50
C
60max 150max 290max
DRIFT[mV]
*
2
20max 48max 96max
ST ART -UP TIME[ms] 150typ (ACIN 100V, Io=100%)
HOLD-UP TIME[ms] 20typ (ACIN 100V, Io=100%)
OUTPUT V OL T AGE SETTING[V]
4.90 to 5.30 11.50 to 12.50 23.00 to 25.00
PROTECTION
CIRCUIT AND
OTHERS
OVERCURRENT PROTECTION
Works over 105% of rating and recovers automatically
OVERVOLTAGE PROTECTION[V]
5.75 to 7.00 13.80 to 16.80 27.60 to 33.60
OPERATING INDICATION LED (Green)
REMOTE SENSING Not provided
REMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature)
ENVIRONMENT
OPERA TING TEMP .,HUMID.AND AL TITUDE
-10 to +60C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max
*3
STORAGE TEMP .,HUMID.AND AL TITUDE
-20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis
IMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY AND
NOISE
REGULATIONS
AGENCY APPROVALS DEN-AN
CONDUCTED NOISE/POWER
Complies with DEN-AN
HARMONIC ATTENUATOR
*
4
Complies with IEC61000-3-2 class A (Not built-in to active fi lter)
OTHERS CASE SIZE/WEIGHT 61X36X150mm [2.40X1.42X5.91 inches] (WXHXD) / 370g max
COOLING METHOD Convection
*1 Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103).
*2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output.
*3 Derating is required.
*4 When two or more units are operating it may not comply with the IEC61000-3-2. Please contact us about another class.
*5 Please contact us about dynamic load and input response.
* To meet the specifi cations. Do not operate over-loaded condition.
* Parallel operation is not possible.
* Derating is required when operated with chassis and cover.
* Sound noise may be generated by power supply in case of pulse load.
SPLFA
mesplfa.indd2me splfa indd 2 2015/06/1815:00:472015/06/18 15:00:47
SPLFA-3
SPLFA30F
External view
Block diagram
AC IN
85 - 264V DC OUT
LFA30F
Tolerance : ±1 [±0.04]
Weight
:
370g max
Chassis and cover material : Electric galvanizing steel board
Dimensions in mm, [ ]=inches
Input wire : VCTF 0.75sqX2C
PCB material/thickness
:
CEM3 / 1.6mm [0.06]
Mounting torque
: M4 :
1.6N-m (16.9kgf-cm) max
[5.51]
[0.59]
[2.40]
[1.97]
[17.72
±
3.94]
[2-f0.14]
[2-f0.14]
[1.02]
[1.42]
[5.91]
[5.51]
[1.00] [0.37]
[0.32]
[0.71]
[2-R0.07]
[2-R0.07]
2-R1.75
2-R1.75
-V Output terminal(-)
+V Output terminal(+)
2-
f
3.5
2-
f
3.5
Name plate
M4
AC(L) : Black
AC(N) : White
Terminal cover
Input
LED
150
140±0.5
50±0.5
61
36
26
±
0.5
140±0.5
25.5 9.5
15±2
8.2
18±1.5
450±100
Mounting hole
Mounting hole
SPLFA
mesplfa.indd3me splfa indd 3 2015/06/1815:00:512015/06/18 15:00:51
SPLFA-4
SPLFA50F
AC-DC Power Supplies Open Frame/Enclosed Value-added Type
SPLF A 50 F -O -O
Ordering information
1 2 3 4 5 6
1 Series name
2 Single output
3 Output wattage
4 Universal input
5 Output voltage
6 Optional
C
: with Coating
MODEL SPLFA50F-5 SPLFA50F-12 SPLFA50F-24
MAX OUTPUT WATTAGE[W] 50 51.6 50.4
DC OUTPUT 5V 10A 12V 4.3A 24V 2.1A
SPECIFICATIONS
MODEL SPLFA50F-5 SPLFA50F-12 SPLFA50F-24
INPUT
VOLTAGE[V] AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.1)
*3
CURRENT[A]
ACIN 100V
0.67typ (Io=100%)
ACIN 200V
0.36typ (Io=100%)
FREQUENCY[Hz] 50 / 60 (47 - 63)
EFFICIENCY[%]
ACIN 100V
76.5typ 79.0typ 80.5typ
ACIN 200V
78.0typ 80.5typ 82.0typ
POWER FACTOR (Io=100%)
ACIN 100V
0.97typ
ACIN 200V
0.90typ
INRUSH CURRENT[A]
ACIN 100V
15typ (Io=100%) (At cold start) (Ta=25C)
ACIN 200V
30typ (Io=100%) (At cold start) (Ta=25C)
LEAKAGE CURRENT[mA] 0.40 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
OUTPUT
VOLTAGE[V] 51224
CURRENT[A] 10.0 4.3 2.1
LINE REGULATION[mV]
*4
20max 48max 96max
LOAD REGULATION[mV]
*4
150max 150max 150max
RIPPLE[mVp-p]
0 to +50C
*1
100max 120max 120max
-10 - 0C
*1
140max 160max 160max
RIPPLE NOISE[mVp-p]
0 to +50C
*1
250max 250max 250max
-10 - 0C
*1
300max 300max 300max
TEMPERATURE REGULATION[mV]
0 to +50C
50max 120max 240max
-10 to +50
C
60max 150max 290max
DRIFT[mV]
*
2
20max 48max 96max
ST ART -UP TIME[ms] 350typ (ACIN 100V, Io=100%)
HOLD-UP TIME[ms] 20typ (ACIN 100V, Io=100%)
OUTPUT V OL T AGE SETTING[V]
4.90 to 5.30
11.50 to 12.50 23.00 to 25.00
PROTECTION
CIRCUIT AND
OTHERS
OVERCURRENT PROTECTION
Works over 105% of rating and recovers automatically
OVERVOLTAGE PROTECTION[V]
5.75 to 7.00
13.80 to 16.80 27.60 to 33.60
OPERATING INDICATION LED (Green)
REMOTE SENSING Not provided
REMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature)
ENVIRONMENT
OPERA TING TEMP .,HUMID.AND AL TITUDE
-10 to +50C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max
*3
STORAGE TEMP .,HUMID.AND AL TITUDE
-20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis
IMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY AND
NOISE
REGULATIONS
AGENCY APPROVALS DEN-AN
CONDUCTED NOISE/POWER
Complies with DEN-AN
HARMONIC ATTENUATOR
*
5
Complies with IEC61000-3-2 (class A)
OTHERS CASE SIZE/WEIGHT 61X36X174mm [2.40X1.42X6.85 inches] (WXHXD) / 440g max
COOLING METHOD Convection
*1 Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103).
*2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output.
*3 Derating is required.
*4 Please contact us about dynamic load and input response.
*5 When two or more units are operating it may not comply with the IEC61000-3-2. Please contact us about another class.
* To meet the specifi cations. Do not operate over-loaded condition.
* Parallel operation is not possible.
* Derating is required when operated with chassis and cover.
* Sound noise may be generated by power supply in case of pulse load.
SPLFA
mesplfa.indd4me splfa indd 4 2015/06/1815:00:512015/06/18 15:00:51
SPLFA-5
SPLFA50F
External view
Block diagram
AC IN
85 - 264V DC OUT
LFA50F
Tolerance : ±1 [±0.04]
Weight
:
440g max
Chassis and cover material : Electric galvanizing steel board
Dimensions in mm, [ ]=inches
PCB material/thickness
:
CEM3 / 1.6mm [0.06]
Mounting torque
: M4 :
1.6N-m (16.9kgf-cm) max
[6.46]
[6.46]
[6.85]
Input wire : VCTF 0.75sqX2C
[1.42]
[1.02]
[17.72
±
3.94]
[2.40]
[1.97]
[2-f0.14]
[2-f0.14]
[0.59]
[1.00] [0.37]
[0.32]
[0.71]
[2-R0.07]
[2-R0.07]
LED
AC(N) : White
AC(L) : Black Input
2-R1.75
Terminal cover
2-R1.75
2-f3.5
2-f3.5
Name plate
M4
18
±
1.5
8.2
9.5
25.5
15
±
2
36 61
174
26
±
0.5
50±0.5
164±0.5
164±0.5
450±100
Mounting hole
Mounting hole
-V Output terminal(-)
+V Output terminal(+)
SPLFA
mesplfa.indd5me splfa indd 5 2015/06/1815:00:552015/06/18 15:00:55
SPLFA-6
SPLFA75F
AC-DC Power Supplies Open Frame/Enclosed Value-added Type
SPLF A 75 F -O -O
Ordering information
1 2 3 4 5 6
1 Series name
2 Single output
3 Output wattage
4 Universal input
5 Output voltage
6 Optional
C
: with Coating
MODEL SPLFA75F-5 SPLFA75F-12 SPLFA75F-24
MAX OUTPUT WATTAGE[W] 75 75.6 76.8
DC OUTPUT 5V 15A 12V 6.3A 24V 3.2A
SPECIFICATIONS
MODEL SPLFA75F-5 SPLFA75F-12 SPLFA75F-24
INPUT
VOLTAGE[V] AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.1)
*3
CURRENT[A]
ACIN 100V
1.00typ (Io=100%)
ACIN 200V
0.50typ (Io=100%)
FREQUENCY[Hz] 50 / 60 (47 - 63)
EFFICIENCY[%]
ACIN 100V
75.0typ 80.0typ 81.5typ
ACIN 200V
77.0typ 82.0typ 83.5typ
POWER FACTOR (Io=100%)
ACIN 100V
0.97typ
ACIN 200V
0.90typ
INRUSH CURRENT[A]
ACIN 100V
15typ (Io=100%) (At cold start) (Ta=25C)
ACIN 200V
30typ (Io=100%) (At cold start) (Ta=25C)
LEAKAGE CURRENT[mA] 0.40 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
OUTPUT
VOLTAGE[V] 51224
CURRENT[A] 15.0 6.3 3.2
LINE REGULATION[mV]
*4
20max 48max 96max
LOAD REGULATION[mV]
*4
150max 150max 150max
RIPPLE[mVp-p]
0 to +50C
*1
100max 120max 120max
-10 - 0C
*1
140max 160max 160max
RIPPLE NOISE[mVp-p]
0 to +50C
*1
250max 250max 250max
-10 - 0C
*1
300max 300max 300max
TEMPERATURE REGULATION[mV]
0 to +50C
50max 120max 240max
-10 to +50
C
60max 150max 290max
DRIFT[mV]
*
2
20max 48max 96max
ST ART -UP TIME[ms] 350typ (ACIN 100V, Io=100%)
HOLD-UP TIME[ms] 20typ (ACIN 100V, Io=100%)
OUTPUT V OL T AGE SETTING[V]
4.90 to 5.30 11.50 to 12.50 23.00 to 25.00
PROTECTION
CIRCUIT AND
OTHERS
OVERCURRENT PROTECTION
Works over 105% of rating and recovers automatically
OVERVOLTAGE PROTECTION[V]
5.75 to 7.00 13.80 to 16.80 27.60 to 33.60
OPERATING INDICATION LED (Green)
REMOTE SENSING Not provided
REMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature)
ENVIRONMENT
OPERA TING TEMP .,HUMID.AND AL TITUDE
-10 to +50C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max
*3
STORAGE TEMP .,HUMID.AND AL TITUDE
-20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis
IMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY AND
NOISE
REGULATIONS
AGENCY APPROVALS DEN-AN
CONDUCTED NOISE/POWER
Complies with DEN-AN
HARMONIC ATTENUATOR
*
5
Complies with IEC61000-3-2 (class A)
OTHERS CASE SIZE/WEIGHT 61X42X192mm [2.40X1.65X7.56 inches] (WXHXD) / 540g max
COOLING METHOD Convection
*1 Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103).
*2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output.
*3 Derating is required.
*4 Please contact us about dynamic load and input response.
*5 When two or more units are operating it may not comply with the IEC61000-3-2. Please contact us about another class.
* To meet the specifi cations. Do not operate over-loaded condition.
* Parallel operation is not possible.
* Derating is required when operated with chassis and cover.
* Sound noise may be generated by power supply in case of pulse load.
SPLFA
mesplfa.indd6me splfa indd 6 2015/06/1815:00:552015/06/18 15:00:55
SPLFA-7
SPLFA75F
External view
Block diagram
AC IN
85 - 264V DC OUT
LFA75F
Tolerance : ±1 [±0.04]
Weight
:
540g max
Chassis and cover material : Electric galvanizing steel board
Dimensions in mm, [ ]=inches
PCB material/thickness
:
CEM3 / 1.6mm [0.06]
[7.56]
[7.17]
[7.17]
[2.40]
[1.97]
[1.65]
[1.26]
[17.72
±
3.94]
[2-f0.14]
[2-f0.14]
Input wire : VCTF 0.75sqX2C
Mounting torque
: M4 :
1.6N-m (16.9kgf-cm) max
[0.59]
[1.00] [0.37]
[0.32]
[0.71]
[2-R0.07]
[2-R0.07]
M4
LED
Terminal cover
2-R1.75
Name plate
2-f3.5
Input
AC(L) : Black
AC(N) : White
2-f3.5 2-R1.75
192
182±0.5
61
50±0.5
42
32
±
0.5
182±0.5
18±1.5
15±2
25.5 9.5
8.2
450±100
Mounting hole
Mounting hole
+V Output terminal(+)
-V Output terminal(-)
SPLFA
mesplfa.indd7me splfa indd 7 2015/06/1815:00:582015/06/18 15:00:58
SPLFA-8
SPLFA100F
AC-DC Power Supplies Open Frame/Enclosed Value-added Type
SPLF A 100 F -O -O
Ordering information
1 2 3 4 5 6
1 Series name
2 Single output
3 Output wattage
4 Universal input
5 Output voltage
6 Optional
C
: with Coating
MODEL SPLFA100F-12 SPLFA100F-24
MAX OUTPUT WATTAGE[W] 102.0 103.2
DC OUTPUT 12V 8.5A 24V 4.3A
SPECIFICATIONS
MODEL SPLFA100F-12 SPLFA100F-24
INPUT
VOLTAGE[V] AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.1)
*3
CURRENT[A]
ACIN 100V
1.3typ (Io=100%)
ACIN 200V
0.7typ (Io=100%)
FREQUENCY[Hz] 50 / 60 (47 - 63)
EFFICIENCY[%]
ACIN 100V
80.5typ 83.0typ
ACIN 200V
83.5typ 86.0typ
POWER FACTOR (Io=100%)
ACIN 100V
0.97typ
ACIN 200V
0.90typ
INRUSH CURRENT[A]
ACIN 100V
15typ (Io=100%) (At cold start) (Ta=25C)
ACIN 200V
30typ (Io=100%) (At cold start) (Ta=25C)
LEAKAGE CURRENT[mA] 0.40 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
OUTPUT
VOLTAGE[V] 12 24
CURRENT[A] 8.5 4.3
LINE REGULATION[mV]
*4
48max 96max
LOAD REGULATION[mV]
*4
150max 150max
RIPPLE[mVp-p]
0 to +50C
*1
120max 120max
-10 - 0C
*1
160max 160max
RIPPLE NOISE[mVp-p]
0 to +50C
*1
250max 250max
-10 - 0C
*1
300max 300max
TEMPERATURE REGULATION[mV]
0 to +50C
120max 240max
-10 to +50
C
150max 290max
DRIFT[mV]
*
2
48max 96max
ST ART -UP TIME[ms] 350typ (ACIN 100V, Io=100%)
HOLD-UP TIME[ms] 20typ (ACIN 100V, Io=100%)
OUTPUT V OL T AGE SETTING[V]
11.50 to 12.50 23.00 to 25.00
PROTECTION
CIRCUIT AND
OTHERS
OVERCURRENT PROTECTION
Works over 105% of rating and recovers automatically
OVERVOLTAGE PROTECTION[V]
13.80 to 16.80 27.60 to 33.60
OPERATING INDICATION LED (Green)
REMOTE SENSING Not provided
REMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature)
ENVIRONMENT
OPERA TING TEMP .,HUMID.AND AL TITUDE
-10 to +50C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max
*3
STORAGE TEMP .,HUMID.AND AL TITUDE
-20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis
IMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY AND
NOISE
REGULATIONS
AGENCY APPROVALS DEN-AN
CONDUCTED NOISE/POWER
Complies with DEN-AN
HARMONIC ATTENUATOR
*
5
Complies with IEC61000-3-2 (class A)
OTHERS CASE SIZE/WEIGHT 73X42X197mm [2.87X1.65X7.76 inches] (WXHXD) / 670g max
COOLING METHOD Convection
*1 Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103).
*2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output.
*3 Derating is required.
*4 Please contact us about dynamic load and input response.
*5 When two or more units are operating it may not comply with the IEC61000-3-2. Please contact us about another class.
* To meet the specifi cations. Do not operate over-loaded condition.
* Parallel operation is not possible.
* Derating is required when operated with chassis and cover.
* Sound noise may be generated by power supply in case of pulse load.
SPLFA
mesplfa.indd8me splfa indd 8 2015/06/1815:00:592015/06/18 15:00:59
SPLFA-9
SPLFA100F
External view
Block diagram
AC IN
85 - 264V DC OUT
LFA100F
Tolerance : ±1 [±0.04]
Weight
:
670g max
Chassis material : Galvanized Steel board
Screw tightening torque
: M4 :
1.6N-m (16.9kgf-cm) max
Dimensions in mm, [ ]=inches
Input wire : VCTF 0.75sqX2C
[2-f0.14]
[2-f0.14] [2-R0.07]
[2-R0.07]
[2.87]
[1.65]
[1.26] [2.44]
[1.24] [0.37]
[0.32]
[17.72±3.94]
[7.36]
[7.36]
[0.59]
[0.71]
[7.76]
M4
Mounting hole
2-f3.5
2-R1.75
LED
+V Output terminal(+)
-V Output terminal(-)
Terminal cover
2-R1.75
N (White)
L
(Black) Input wire
Mounting hole
2-f3.5
Name plate
18±1.5
187±0.5
42
32±0.5
73
62±0.5
197
187±0.5
15±2
8.2
9.5
31.5
450±100
SPLFA
mesplfa.indd9me splfa indd 9 2015/06/1815:01:032015/06/18 15:01:03
SPLFA-10
SPLFA150F
AC-DC Power Supplies Open Frame/Enclosed Value-added Type
SPLF A 150 F -O -O
Ordering information
1 2 3 4 5 6
1 Series name
2 Single output
3 Output wattage
4 Universal input
5 Output voltage
6 Optional
C
: with Coating
MODEL SPLFA150F-12 SPLFA150F-24
MAX OUTPUT WATTAGE[W] 150 151.2
DC OUTPUT 12V 12.5A 24V 6.3A
SPECIFICATIONS
MODEL SPLFA150F-12 SPLFA150F-24
INPUT
VOLTAGE[V] AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.1)
*3
CURRENT[A]
ACIN 100V
2.0typ (Io=100%)
ACIN 200V
1.0typ (Io=100%)
FREQUENCY[Hz] 50 / 60 (47 - 63)
EFFICIENCY[%]
ACIN 100V
81.0typ 84.0typ
ACIN 200V
84.0typ 86.5typ
POWER FACTOR (Io=100%)
ACIN 100V
0.97typ
ACIN 200V
0.90typ
INRUSH CURRENT[A]
ACIN 100V
15typ (Io=100%) (At cold start) (Ta=25C)
ACIN 200V
30typ (Io=100%) (At cold start) (Ta=25C)
LEAKAGE CURRENT[mA] 0.40 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
OUTPUT
VOLTAGE[V] 12 24
CURRENT[A] 12.5 6.3
LINE REGULATION[mV]
*4
48max 96max
LOAD REGULATION[mV]
*4
150max 150max
RIPPLE[mVp-p]
0 to +50C
*1
120max 120max
-10 - 0C
*1
160max 160max
RIPPLE NOISE[mVp-p]
0 to +50C
*1
250max 250max
-10 - 0C
*1
300max 300max
TEMPERATURE REGULATION[mV]
0 to +50C
120max 240max
-10 to +50
C
150max 290max
DRIFT[mV]
*
2
48max 96max
ST ART -UP TIME[ms] 350typ (ACIN 100V, Io=100%)
HOLD-UP TIME[ms] 20typ (ACIN 100V, Io=100%)
OUTPUT V OL T AGE SETTING[V]
11.50 to 12.50 23.00 to 25.00
PROTECTION
CIRCUIT AND
OTHERS
OVERCURRENT PROTECTION
Works over 105% of rating and recovers automatically
OVERVOLTAGE PROTECTION[V]
13.80 to 16.80 27.60 to 33.60
OPERATING INDICATION LED (Green)
REMOTE SENSING Not provided
REMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature)
ENVIRONMENT
OPERA TING TEMP .,HUMID.AND AL TITUDE
-10 to +50C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max
*3
STORAGE TEMP .,HUMID.AND AL TITUDE
-20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis
IMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY AND
NOISE
REGULATIONS
AGENCY APPROVALS DEN-AN
CONDUCTED NOISE/POWER
Complies with DEN-AN
HARMONIC ATTENUATOR
*
5
Complies with IEC61000-3-2 (class A)
OTHERS CASE SIZE/WEIGHT 86X47X202mm [3.39X1.85X7.95 inches] (WXHXD) / 850g max
COOLING METHOD Convection
*1 Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103).
*2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output.
*3 Derating is required.
*4 Please contact us about dynamic load and input response.
*5 When two or more units are operating it may not comply with the IEC61000-3-2. Please contact us about another class.
* To meet the specifi cations. Do not operate over-loaded condition.
* Parallel operation is not possible.
* Derating is required when operated with chassis and cover.
* Sound noise may be generated by power supply in case of pulse load.
SPLFA
mesplfa.indd10me splfa indd 10 2015/06/1815:01:042015/06/18 15:01:04
SPLFA-11
SPLFA150F
External view
Block diagram
AC IN
85 - 264V DC OUT
LFA150F
Tolerance : ±1 [±0.04]
Weight
:
850g max
Chassis material : Galvanized Steel board
Screw tightening torque
: M4 :
1.6N-m (16.9kgf-cm) max
Dimensions in mm, [ ]=inches
Input wire : VCTF 0.75sqX2C
[2-R0.07]
[2-R0.07]
[1.50] [0.37]
[0.32]
[7.56]
[7.56]
[0.59]
[0.71]
[7.95]
[2-f0.14]
[2-f0.14]
[3.39]
[1.85]
[1.46] [2.95]
[17.72±3.94]
Name plate 2-R1.75
Terminal cover
2-f3.5
Mounting hole
Input wire
L
(Black)
N (White)
2-f3.5
Mounting hole 2-R1.75
LED
-V Output terminal(-)
+V Output terminal(+)
M4
8.2
9.5
38
15±2
18±1.5
450±100
47
37±0.5
192 ±0.5
86
75±0.5
202
192±0.5
SPLFA
mesplfa.indd11me splfa indd 11 2015/06/1815:01:062015/06/18 15:01:06