Reflective Object Sensor OPB706A, OPB706B, OPB706C OPB707A, OPB707B, OPB707C Features: * Choice of Phototransistor (OPB706) or Photodarlington (OPB707) output Product Photo Here * Unfocused for sensing diffuse surface * Low cost plastic housing * Designed for use with PCBoards or connectors Description: The OPB706 consists of an infrared Light Emitting Diode (LED) and an NPN silicon Phototransistor mounted "side-by-side" on parallel axes in a black plastic housing. The OPB707 consists of an infrared LED and an NPN silicon Photodarlington mounted "side-by-side" on parallel axes in a black plastic housing. On both OPB706 and OPB707, the LED and Phototransistor / Photodarlington are molded using dark infrared transmissive plastic to reduce ambient light noise. The Phototransistor / Photodarlington responds to light from the emitter when a reflective object passes within its field of view of the device. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications: * * * * * * Part Number Non-contact reflective object sensor LED Peak Wavelength Assembly line automation OPB706A Machine automation OPB706B Machine safety OPB706C End of travel sensor OPB707A Door sensor OPB707B Sensor Reflection Distance Lead Length / Spacing 0.050" (1.27mm) 0.45" / 0.087", 0.100" Transistor 935 nm Darlington OPB707C OPB706 3 1 4 2 OPB707 [ MILLIMETERS] DIMENSIONS ARE IN: 3 1 4 2 INCHES RoHS Pin # LED Pin # Transistor 3 Anode 1 Collector 4 Cathode 2 Emitter OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.1 11/06 Page 1 of 4 Reflective Object Sensor OPB706A, OPB706B, OPB706C OPB707A, OPB707B, OPB707C Absolute Maximum Ratings (TA=25C unless otherwise noted) Storage and Operating Temperature Range Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] -40 C to +85 C (1) 260 C Input Diode Forward DC Current 50 mA Peak Forward Current (1 s pulse width, 300 pps) 3A Reverse DC Voltage 2V Power Dissipation (2) 75 mW Output Phototransistor (OPB706) | Output Photodarlington (OPB707) Collector-Emitter Voltage OPB706 OPB707 24 V 15 V Emitter-Collector Voltage 5V Collector DC Current OPB706 OPB707 25 mA 125 mA Power Dissipation OPB706(2) OPB707(3) 75 mW 100 mW Notes: (1) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (2) Derate linearly 1.25 mW/C above 25 C. (3) Derate linearly 1.67 mW/C above 25 C. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A1 11/06 Page 2 of 4 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Reflective Object Sensor OPB706A, OPB706B, OPB706C OPB707A, OPB707B, OPB707C Electrical Characteristics (TA=25C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (see OP165W for additional information) VF Forward Voltage - - 1.7 V IF = 20 mA IR Reverse Current - - 100 A VR = 2 V Output Phototransistor (see OP505W for additional information) | Photodarlington (see OP535 for additional information) V(BR)CEO Collector-Emitter Brealdown Voltage OPB706 OPB707 24 15 - - V IC = 100 A V(BR)ECO Emitter-Collector Breakdown Voltage 5 - - V IE = 100 A Collector Dark Current OPB706 OPB707 - - 100 250 nA VCE = 5 V, IF = 0, EE 0.1 W/cm2 Crosstalk OPB706 OPB707 - - 200 10 mA A IF = 20 mA, VCE = 5 V, No reflecting surface(1) On-State Collector Current OPB706A OPB706B OPB706C 500 350 250 - - OPB707A OPB707B OPB707C 25 17 10 - - ICEO Combined ICX IC(ON) VCE(SAT) Collector-Emitter Saturation Voltage OPB706 OPB707 0.4 1.1 - - A IF = 20 mA, VCE = 5V , d = 0.05" (1.27 mm)(2) (3) mA V IF = 20 mA, d = 0.05" (1.27 mm)(2) (3) IC(ON) = 100A IC(ON) = 2 mA Notes: (1) Crosstalk (ICX) is the collector current measured with the indicated current in the input diode and with no reflecting surface. (2) The distance from the assembly face to the reflective surface is "d". (3) Measured using Eastman Kodak neutral white test card with 90% diffuse reflectance as a reflecting surface. Reference: Eastman Kodak, Catalog #E 152 7795. (4) Lower curve is a calculated worst case condition rather than the conventional -2 limit. (5) All parameters tested using pulse techniques. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.1 11/06 Page 3 of 4 Reflective Object Sensor OPB706A, OPB706B, OPB706C OPB707A, OPB707B, OPB707C OPB706 - Output Current vs Forward Current vs Temperature OPB706 - Normalized Collector Current vs. Object Distance 3.0 1.2 Normalized at IF = 20mA at 20C, VCC = 5V i K d k 90% t Di t 0 050" VCE = 5V, IF = 20mA, Normalized at 0.050" Kodak 90% 2.5 Normalized Output Current Normalized Output Current 1.0 0.8 Kodak 90% Kodak 19% Copy Paper Avery 0.6 Retro Reflective 0.4 0.2 2.0 1.5 1.0 -40 C -20 C 0.5 0 C 20 C 40 C 60 C 80 C 0.0 0.0 0.0 0.2 0.4 0.6 0.8 1.0 0 5 10 15 Distance to Reflective Surface (inches) 20 25 30 35 40 45 50 Forward Current - mA OPB707 - Normalized Collector Current vs. Object Distance OPB707 - Output Current vs Forward Current vs Temperature 1.6 1.2 Normalized at IF = 20mA at 20C, VCC = 5V using Kodak 90% at Distance = 0.050" (1.27mm) VCE = 5V, IF = 20mA, Normalized at 0.050" Kodak 90% 1.4 Normalized Output Current Normalized Output Current 1.0 0.8 Kodak 90% Kodak 18% Copy Paper Avery Retro Reflective 0.6 0.4 1.2 1.0 0.8 -40 C -20 C 0 C 20 C 40 C 60 C 80 C 0.6 0.4 0.2 0.2 0.0 0.0 0.0 0.2 0.4 0.6 0.8 Distance to Reflective Surface (inches) 1.0 0 5 10 15 20 25 30 35 40 45 50 Forward Current - mA OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A1 11/06 Page 4 of 4 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com