MKP3V240RLG - ON SEMICONDUCTOR

June, 2012− Rev. 6

1Publication Order Number:

MKP3V120/D

MKP3V120, MKP3V240

Sidac High Voltage

Bidirectional Triggers

Bidirectional devices designed for direct interface with the AC

power line. Upon reaching the breakover voltage in each direction, the

device switches from a blocking state to a low voltage on−state.

Conduction will continue like a Triac until the main terminal current

drops below the holding current. The plastic axial lead package

provides high pulse current capability at low cost. Glass passivation

insures reliable operation.

Features

•High Pressure Sodium Vapor Lighting

•Strobes and Flashers

•Ignitors

•High Voltage Regulators

•Pulse Generators

•Used to Trigger Gates of SCR’s and Triacs

• Indicates UL Registered − File #E210057

•These are Pb−Free Devices*

MAXIMUM RATINGS (TJ = 25°C unless otherwise noted)

Rating Symbol Value Unit

Peak Repetitive Off−State Voltage

(Sine Wave, 50 to 60 Hz, TJ = −40 to 125°C)

MKP3V120

MKP3V240

VDRM,

VRRM

"90

"180

On-State RMS Current (TL = 80°C, Lead

Length = 3/8″, All Conduction Angles)

IT(RMS) "1.0 A

Peak Non−Repetitive Surge Current

(60 Hz One Cycle Sine Wave, Peak Value,

TJ = 125°C)

ITSM "20 A

Operating Junction Temperature Range TJ−40 to +125 °C

Storage Temperature Range Tstg −40 to +150 °C

THERMAL CHARACTERISTICS

Characteristic Symbol Max Unit

Thermal Resistance, Junction−to−Lead

(Lead Length = 3/8″)

RqJL 15 °C/W

Lead Solder Temperature

(Lead Length w 1/16″ from Case, 10 s Max)

TL260 °C

Stresses exceeding Maximum Ratings may damage the device. Maximum

Ratings are stress ratings only. Functional operation above the Recommended

Operating Conditions is not implied. Extended exposure to stresses above the

Recommended Operating Conditions may affect device reliability.

*For additional information on our Pb−Free strategy and soldering details, please

download the ON Semiconductor Soldering and Mounting Techniques

Reference Manual, SOLDERRM/D.

SIDACS

1 AMPERE RMS

120 and 240 VOLTS

Device Package Shipping†

ORDERING INFORMATION

MT1 MT2

AXIAL LEAD

(No Polarity)

CASE 267

STYLE 2

()

http://onsemi.com

MKP3V240RLG

MKP3V240G

MKP3V120RLG

MKP3V120G Axial Lead* 500 Units/Box

1500/Tape & Reel

500 Units/Box

1500/Tape & Reel

Axial Lead*

†For information on tape and reel specifications,

including part orientation and tape sizes, please

refer to our Tape and Reel Packaging Specifications

Brochure, BRD8011/D.

MKP

3Vxx0

YYWW G

A = Assembly Location

xx = 12 or 24

YY, Y = Year

WW = Work Week

G= Pb−Free Package

(Note: Microdot may be in either location)

MARKING DIAGRAM

MKP3V120, MKP3V240

http://onsemi.com

ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise noted; Electricals apply in both directions)

Characteristic Symbol Min Typ Max Unit

OFF CHARACTERISTICS

Repetitive Peak Off−State Current

(50 to 60 Hz Sine Wave)

VDRM = 90 V MKP3V120

VDRM = 180 V MKP3V240

IDRM − − 10 mA

ON CHARACTERISTICS

Breakover Voltage, IBO = 200 mA

MKP3V120

MKP3V240

VBO

110

220

−

130

250

Breakover Current IBO − − 200 mA

Peak On−State Voltage

(ITM = 1 A Peak, Pulse Width ≤ 300 ms, Duty Cycle ≤ 2%)

VTM −1.1 1.5 V

Dynamic Holding Current

(Sine Wave, 60 Hz, RL = 100 W)

IH− − 100 mA

Switching Resistance

(Sine Wave, 50 to 60 Hz)

RS0.1 − − kW

DYNAMIC CHARACTERISTICS

Critical Rate−of−Rise of On−State Current,

Critical Damped Waveform Circuit

(IPK = 130 W, Pulse Width = 10 msec)

di/dt −120 −A/ms

+ Current

+ Voltage

VTM

Symbol Parameter

IDRM Off State Leakage Current

VDRM Off State Repetitive Blocking Voltage

VBO Breakover Voltage

IBO Breakover Current

IHHolding Current

VTM On State Voltage

ITM Peak on State Current

Voltage Current Characteristic of SIDAC

VDRM

IDRM

ITM Slope = RS

V(BO)

RS+

(V(BO) –V

(IS–I

(BO))

I(BO)

(Bidirectional Device)

MKP3V120, MKP3V240

http://onsemi.com

CURRENT DERATING

Figure 1. Maximum Case Temperature Figure 2. Maximum Ambient Temperature

Figure 3. Typical Forward Voltage Figure 4. Typical Power Dissipation

0.80

IT(AV), AVERAGE ON-STATE CURRENT (AMPS)

120

IT(AV), AVERAGE ON-STATE CURRENT (AMPS)

0.4

1.0 1.10.8

VT, INSTANTANEOUS ON-STATE VOLTAGE (VOLTS)

0.3

0.4

0.2

0.1

0.9

1.2

0.2 0.6

100

0.6

1.0

130

, MAXIMUM ALLOWABLE CASE TEMPERATURE ( C)

1.00

100

0.4

0.2 0.6

, MAXIMUM ALLOWABLE AMBIENT

0.2 0.60

IT(AV), AVERAGE ON-STATE CURRENT (AMPS)

0.50

0.75

0.25

0.4 0.8

1.00

1.25

1.61.2

1.0 1.4 2.01.8

110

0.8 1.2 1.4

1.3

, INSTANTANEOUS ON-STATE CURRENT (AMPS)

1.0

, MAXIMUM AVERAGE POWER DISSIPATION (WATTS)

25°C125°C

0.8

α = Conduction Angle

TJ Rated = 125°C

α = Conduction Angle

TJ Rated = 125°C

α = Conduction Angle

TJ Rated = 125°C

1.6 1.8 2.

120

140

a = 180°

TEMPERATURE ( C)°

a = 180°

MKP3V120, MKP3V240

http://onsemi.com

THERMAL CHARACTERISTICS

Figure 5. Thermal Response

t, TIME (ms)

0.03

0.02

0.01

5.00.2 0.5 1.0 2.0

0.05

0.1

0.2

r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED)

0.3

0.5

1.0

20 50 100 200 500 1.0 k 2.0 k 5.0 k 10 k

The temperature of the lead should be

measured using a thermocouple placed on the

lead as close as possible to the tie point. The

thermal mass connected to the tie point is

normally large enough so that it will not

significantly respond to heat surges generated

in the diode as a result of pulsed operation

once steady-state conditions are achieved.

Using the measured value of TL, the junction

temperature may be determined by:

TJ = TL + DTJL

20 k

LEAD LENGTH = 1/4″

ZqJL(t) = RqJL • r(t)

DTJL = Ppk RqJL[r(t)]

where:

DTJL = the increase in junction temperature above the

lead temperature

r(t) = normalized value of transient thermal resistance at

time, t from this figure. For example,

r(tp) = normalized value of

transient resistance at time tp.

TIME

TYPICAL CHARACTERISTICS

Figure 6. Typical Breakover Current Figure 7. Typical Holding Current

TJ, JUNCTION TEMPERATURE (°C)

-60

-40 -20 100 140

100

TJ, JUNCTION TEMPERATURE (°C)

100-60

40-40 -20 0 20

100

125

, BREAKOVER CURRENT ( A)

(BO)

8060 120 140

, HOLDING CURRENT (mA)

120

0604020

150

175

200

225

250

MKP3V120, MKP3V240

http://onsemi.com

PACKAGE DIMENSIONS

DIM MIN MAX MIN MAX

MILLIMETERSINCHES

A0.370 0.380 9.40 9.65

B0.190 0.210 4.83 5.33

D0.048 0.052 1.22 1.32

K1.000 --- 25.40 ---

STYLE 2:

NO POLARITY

NOTES:

1. DIMENSIONS AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. 267-01 AND 267-02 OBSOLETE, NEW STANDARD

267-03.

AXIAL LEAD

CASE 267

ISSUE G

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,

copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC

reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any

particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without

limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications

and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC

does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for

surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where

personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and

its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,

any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture

of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5817−1050

MKP3V120/D

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your local

Sales Representative