E M C C o m p o n e n t s July 2014 Chip Beads For general signal line GHz noise countermeasure (general signal line, high-speed signal line) MMZ-E series MMZ0603-E MMZ1005-E 0603[0201 inch]* 1005[0402 inch] * Dimensions Code JIS[EIA] (2/13) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (3/13) E M C C o m p o n e n t s Chip Beads Product compatible with RoHS directive Halogen-free Compatible with lead-free solders For general signal line GHz noise countermeasure (general signal line, high-speed signal line) Overview of the MMZ-E Series FEATURES Noise reduction solution for general signal line. Compared to the MMZ Series, it is a product that increases the SRF to GHz bands and can countermeasure nose at wide frequencies with 1 element. Compared to the MMZ Series, it can attain high impedance at GHz bands. Lineup includes 2 sizes: 0603 and 1005. Various frequency characteristics with 4 materials of different features for countermeasures against everything from general signals to high-speed signals. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION MMZ Series name 0603 LxWxT Dimensions (mm) 0603 0.6x0.3x0.3 1005 1.0x0.5x0.5 S Material name S A D F 601 E Impedance (:) at 100MHz 601 600 102 1000 Characteristic type E T 000 Packaging style Internal code T Taping 000 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage Type temperature temperature C C MMZ0603-E -55 to +125 -55 to +125 MMZ1005-E -55 to +125 -55 to +125 The Storage temperature range is for after the circuit board is mounted. Package quantity Individual weight pieces/reel 15,000 10,000 mg 0.3 1 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (4/13) E M C C o m p o n e n t s Overview of the MMZ-E Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (5/13) E M C C o m p o n e n t s MMZ-E series MMZ0603-E Type SHAPE & DIMENSIONS 0.30.03 0.30.03 0.60.03 Dimensions in mm 0.1min. 0.30 RECOMMENDED LAND PATTERN 0.25 0.30 0.25 Dimensions in mm * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (6/13) E M C C o m p o n e n t s MMZ-E series MMZ0603-E Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] (: ) 120 240 600 1000 120 240 33 47 120 56 75 Tolerance 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% [1GHz] (: ) 200 400 1000 1800 300 600 200 300 1000 700 950 Tolerance 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% Measurement equipment Measurement item Product No. Impedance E4991A+16197 DC resistance Type-7556 Equivalent measurement equipment may be used. DC resistance (: )max. Rated current (mA)max. Part No. 0.37 0.71 1.60 2.60 0.44 0.86 0.6 0.76 2.4 1.9 2.6 250 200 150 125 250 200 250 200 125 150 125 MMZ0603S121ET000 MMZ0603S241ET000 MMZ0603S601ET000 MMZ0603S102ET000 MMZ0603A121ET000 MMZ0603A241ET000 MMZ0603D330ET000 MMZ0603D470ET000 MMZ0603D121ET000 MMZ0603F560ET000 MMZ0603F750ET000 Manufacturer Agilent Technologies Yokogawa * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (7/13) E M C C o m p o n e n t s MMZ-E series MMZ0603-E Type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MMZ0603S-E SERIES MMZ0603A-E SERIES 2000 1800 MMZ0603S102E 2000 700 1800 MMZ0603D121E 1600 1600 600 MMZ0603S601E 1000 800 1400 MMZ0603A241E Impedance() 1200 Impedance () Impedance() 1400 500 400 300 1200 1000 800 MMZ0603D470E 600 600 MMZ0603S241E 400 1 MMZ0603D330E 200 400 100 200 0 MMZ0603D-E SERIES 800 MMZ0603S121E 10 100 1000 10000 Frequency (MHz) 0 MMZ0603A121E 1 10 100 1000 Frequency (MHz) 10000 200 0 1 10 100 1000 Frequency (MHz) 10000 MMZ0603F-E SERIES 2500 MMZ0603F750E Impedance() 2000 MMZ0603F560E 1500 1000 500 0 1 10 100 1000 Frequency (MHz) 10000 * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (8/13) E M C C o m p o n e n t s MMZ-E series MMZ0603-E Type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ0603S121ET000 MMZ0603S241ET000 200 Z R 100 X 50 1 10 100 1000 Frequency (MHz) 10000 2000 1800 1600 1400 1200 1000 800 600 400 200 0 Z R X 1 10 100 1000 Frequency (MHz) 10000 R X 10 100 1000 Frequency (MHz) 10000 MMZ0603F560ET000 10 100 1000 Frequency (MHz) 500 450 400 350 300 250 200 150 100 50 0 R 100 1000 Frequency (MHz) 0 10000 R X 10 200 X 1 10 100 1000 Frequency (MHz) 10000 800 700 600 500 400 300 200 100 0 Z R X 1 10 100 1000 Frequency (MHz) 10000 MMZ0603D121ET000 Z 1 R 400 10000 X 10 600 MMZ0603A241ET000 Z 1 Z 800 100 1000 Frequency (MHz) 2000 1800 1600 1400 1200 1000 800 600 400 200 0 10000 Z R X 1 10 100 1000 Frequency (MHz) 10000 MMZ0603F750ET000 Z Impedance () 2500 Impedance () 1600 1400 1200 1000 800 600 400 200 0 1 MMZ0603D470ET000 Z 1 X 350 300 250 200 150 100 50 0 Impedance () Impedance () MMZ0603D330ET000 350 300 250 200 150 100 50 0 R MMZ0603A121ET000 Impedance () Impedance () MMZ0603S102ET000 1000 Z Impedance () 0 1200 Impedance () 150 450 400 350 300 250 200 150 100 50 0 Impedance () Impedance () Impedance () 250 MMZ0603S601ET000 R X 1 10 100 1000 Frequency (MHz) 2000 1500 Z R 1000 500 10000 0 X 1 10 100 1000 Frequency (MHz) 10000 * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (9/13) E M C C o m p o n e n t s MMZ-E series MMZ1005-E Type SHAPE & DIMENSIONS 0.50.05 0.50.05 10.05 Dimensions in mm 0.1min. 0.5 RECOMMENDED LAND PATTERN 0.5 0.4 0.5 Dimensions in mm * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (10/13) E M C C o m p o n e n t s MMZ-E series MMZ1005-E Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] (: ) 600 1000 1800 600 1000 1500 1800 2200 120 220 47 75 120 Tolerance 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% [1GHz] (: ) 1000 1400 1800 1400 2000 2300 2700 3000 1000 1700 800 1500 2300 Tolerance 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% Measurement equipment Measurement item Product No. Impedance E4991A+16192A DC resistance Type-7556 Equivalent measurement equipment may be used. DC resistance (: )max. Rated current (mA)max. Part No. 0.65 1.00 1.50 0.80 1.20 1.60 2.10 2.20 0.70 1.00 0.70 1.00 1.50 300 250 200 300 250 230 200 150 300 250 300 250 200 MMZ1005S601ET000 MMZ1005S102ET000 MMZ1005S182ET000 MMZ1005A601ET000 MMZ1005A102ET000 MMZ1005A152ET000 MMZ1005A182ET000 MMZ1005A222ET000 MMZ1005D121ET000 MMZ1005D221ET000 MMZ1005F470ET000 MMZ1005F750ET000 MMZ1005F121ET000 Manufacturer Agilent Technologies Yokogawa * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (11/13) E M C C o m p o n e n t s MMZ-E series MMZ1005-E Type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MMZ1005S-E SERIES MMZ1005A-E SERIES MMZ1005A222E 4000 5000 Impedance () 1500 1000 500 3000 MMZ1005A102E 2500 2000 10 100 1000 Frequency (MHz) 1200 1000 800 1500 600 1000 400 0 1 1400 MMZ1005A152E 200 500 MMZ1005S601E 10000 MMZ1005D221E 1600 MMZ1005A182E 3500 MMZ1005S102E 2000 1800 Impedance () MMZ1005S182E 2500 Impedance () 2000 4500 3000 0 MMZ1005D-E SERIES MMZ1005A601E 1 10 100 1000 Frequency (MHz) MMZ1005D121E 10000 0 1 10 100 1000 Frequency (MHz) 10000 MMZ1005F-E SERIES 3000 MMZ1005F121E Impedance () 2500 2000 MMZ1005F750E 1500 1000 MMZ1005F470E 500 0 1 10 100 1000 Frequency (MHz) 10000 * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (12/13) E M C C o m p o n e n t s MMZ-E series MMZ1005-E Type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ1005S601ET000 MMZ1005S102ET000 Impedance () Z 600 R 400 X 1 10 100 1000 Frequency (MHz) 10000 MMZ1005A601ET000 Z R X 1 10 100 1000 Frequency (MHz) 10 100 1000 Frequency (MHz) 3500 3000 2500 2000 1500 1000 500 0 R X 10 100 1000 Frequency (MHz) 10000 500 0 10000 Z R X 1 10 100 1000 Frequency (MHz) 4500 4000 3500 3000 2500 2000 1500 1000 500 0 Impedance () 800 Z R 400 10 10 100 1000 Frequency (MHz) 10000 Z 2000 R 1500 1000 X 500 0 1 10 100 1000 Frequency (MHz) 10000 R X 1 10 100 1000 Frequency (MHz) 10000 MMZ1005F470ET000 1200 1500 Z 1000 R 500 X 100 1000 Frequency (MHz) 0 10000 MMZ1005F750ET000 1 10 100 1000 Frequency (MHz) 10000 1000 800 Z 600 R 400 200 0 X 1 10 100 1000 Frequency (MHz) 10000 MMZ1005F121ET000 3000 Impedance () 1800 1600 1400 1200 1000 800 600 400 200 0 1 Z X 1 X 2500 10000 MMZ1005D221ET000 1000 200 R 1000 2000 600 Z 1500 MMZ1005A222ET000 Z 1 2000 3000 500 0 2500 MMZ1005A152ET000 1000 Impedance () Impedance () 1 1500 1200 Impedance () X 2000 10000 MMZ1005D121ET000 Impedance () R 2500 MMZ1005A182ET000 0 Z MMZ1005A102ET000 Impedance () Impedance () 1600 1400 1200 1000 800 600 400 200 0 3000 Impedance () 200 0 1600 1400 1200 1000 800 600 400 200 0 Impedance () Impedance () 800 Impedance () 1000 MMZ1005S182ET000 Z R X 1 10 100 1000 Frequency (MHz) 2500 2000 1500 Z 1000 R 500 10000 0 1 X 10 100 1000 Frequency (MHz) 10000 * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm (13/13) E M C C o m p o n e n t s MMZ-E series Packaging style REEL DIMENSIONS o60min. 2.00.5 1.0 8.4 +2.0 -0.0 o130.2 o210.8 14.4max. o1802.0 Dimensions in mm 4.00.1 B A 8.00.3 2.00.05 3.50.05 1.5 +0.1 0 1.750.1 TAPE DIMENSIONS P1 K Dimensions in mm Type MMZ0603-E MMZ1005-E 160min. A 0.380.05 0.650.1 Taping B 0.680.05 1.150.1 P1 2.00.05 2.00.05 K 0.5max. 0.8max. 200min. Drawing direction 300min. Dimensions in mm * All specifications are subject to change without notice. 001-02 / 20140717 / beads_commercial_signal_mmz-e_en.fm Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TDK: MMZ1005F470ETD25 MMZ1005D121ETD25 MMZ1005S601ETD25 MMZ1005S102ETD25 MMZ1005A152ETD25 MMZ1005F750ETD25 MMZ0603F560ET000 MMZ1005A182ETD25 MMZ1005D221ETD25 MMZ1005A601ETD25 MMZ1005F121ETD25 MMZ0603F750ET000 MMZ1005A102ETD25 MMZ1005A222ETD25 MMZ0603D121ET000 MMZ1005S182ETD25