Mobile Intel(R) 965 Express Chipset Family Datasheet Revision 003 June 2007 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL(R) PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked reserved or undefined. Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The information here is subject to change without notice. Do not finalize a design with this information. The products described in this document may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. This device is protected by U.S. patent numbers 5,315,448 and 6,516,132, and other intellectual property rights. The use of Macrovision's copy protection technology in the device must be authorized by Macrovision and is intended for home and other limited pay-per-view uses only, unless otherwise authorized in writing by Macrovision. Devices incorporating Macrovision's copy protection technology can only be sold or distributed to companies appearing on Macrovision's list of "Authorized Buyers" at: www.macrovision.com. Reverse engineering or disassembly is prohibited. I2C is a two-wire communications bus/protocol developed by Philips. SMBus is a subset of the I2C bus/protocol and was developed by Intel. Implementations of the I2C bus/protocol may require licenses from various entities, including Philips Electronics N.V. and North American Philips Corporation. Intel(R) Active Management Technology requires the platform to have an Intel AMT-enabled chipset, network hardware and software, as well as connection with a power source and a corporate network connection. With regard to notebooks, Intel AMT may not be available or certain capabilities may be limited over a host OS-based VPN or when connecting wirelessly, on battery power, sleeping, hibernating or powered off. For more information, see http://www.intel.com/technology/iamt. Intel, Intel SpeedStep, Intel Core, Centrino, and the Intel logo are trademarks of Intel Corporation in the U.S. and other countries. *Other names and brands may be claimed as the property of others. Copyright (c) 2007, Intel Corporation. All rights reserved. 2 Datasheet Contents 1 Introduction ............................................................................................................ 11 1.1 Mobile Intel(R) PM965 Express Chipset Feature Support ........................................... 12 1.1.1 Processor Support .................................................................................. 12 1.1.2 System Memory Support ......................................................................... 12 1.1.3 Discrete Graphics using PCI Express* Graphics Attach Port .......................... 13 1.1.4 Direct Management Interface ................................................................... 13 1.1.5 Power Management ................................................................................ 13 1.1.6 Security and Manageability (Intel(R) Active Management Technology)............. 13 1.1.7 Package ................................................................................................ 14 1.1.8 Intel(R) Stable Image Platform Program ..................................................... 14 1.2 Mobile Intel(R) GM965 Express Chipset Feature Support .......................................... 14 1.2.1 PCI Express Graphics Attach Port.............................................................. 14 1.2.2 Integrated Graphics................................................................................ 14 1.2.2.1 Analog CRT .............................................................................. 15 1.2.2.2 Dual Channel LVDS ................................................................... 15 1.2.2.3 Analog TV-Out.......................................................................... 15 1.2.2.4 SDVO Ports .............................................................................. 16 1.2.3 Power Management ................................................................................ 16 1.2.4 Intel Stable Image Platform Program ........................................................ 16 1.3 Mobile Intel(R) GL960 Express Chipset Feature Support ........................................... 16 1.3.1 Processor Support .................................................................................. 16 1.3.2 System Memory Support ......................................................................... 17 1.3.3 PCI Express Graphics Attach Port.............................................................. 17 1.3.4 Integrated Graphics................................................................................ 17 1.3.5 ICH Support .......................................................................................... 17 1.3.6 Power Management ................................................................................ 17 1.3.7 Intel Advanced Management Technology ................................................... 17 1.3.8 Intel Stable Image Platform Program ........................................................ 17 1.4 Mobile Intel(R) GME965 Express Chipset Feature Support......................................... 17 1.4.1 Integrated Graphics................................................................................ 17 1.4.1.1 Analog TV-Out.......................................................................... 17 1.5 Mobile Intel(R) GLE960 Express Chipset Feature Support ......................................... 18 1.5.1 Integrated Graphics................................................................................ 18 1.5.1.1 Analog TV-Out.......................................................................... 18 1.6 Terminology ..................................................................................................... 18 1.7 Reference Documents ........................................................................................ 19 2 Signal Description ................................................................................................... 21 2.1 Host Interface................................................................................................... 22 2.1.1 Host Interface Signals............................................................................. 22 2.2 DDR2 Memory Interface ..................................................................................... 25 2.2.1 DDR2 Memory Channel A Interface ........................................................... 25 2.2.2 DDR2 Memory Channel B Interface ........................................................... 26 2.2.3 DDR2 Memory Common Signals ............................................................... 27 2.2.4 DDR2 Memory Reference and Compensation .............................................. 28 2.3 PCI Express Based Graphics Interface Signals ....................................................... 28 2.3.1 Serial DVO and PCI Express*-Based Graphics Signal Mapping....................... 28 2.4 DMI - (G)MCH to ICH Serial Interface .................................................................. 29 2.5 Integrated Graphics Interface Signals .................................................................. 30 2.5.1 CRT DAC Signals .................................................................................... 30 2.5.2 Analog TV-out Signals............................................................................. 31 Datasheet 3 2.6 2.7 2.8 2.9 2.10 2.5.3 LVDS Signals .........................................................................................32 2.5.4 Serial DVO Interface ...............................................................................33 2.5.5 Display Data Channel (DDC) and GMBUS Support .......................................34 Intel(R) Management Engine Interface Signals ........................................................35 PLL Signals .......................................................................................................35 Reset and Miscellaneous Signals ..........................................................................36 Non-Critical to Function (NCTF) ...........................................................................37 Power and Ground .............................................................................................37 3 Host 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Interface..........................................................................................................41 FSB Source Synchronous Transfers ......................................................................41 FSB IOQ Depth..................................................................................................41 FSB OOQ Depth.................................................................................................41 FSB AGTL+ Termination .....................................................................................41 FSB Dynamic Bus Inversion.................................................................................41 FSB Interrupt Overview ......................................................................................42 APIC Cluster Mode Support .................................................................................42 4 System Address Map ................................................................................................43 4.1 Legacy Address Range........................................................................................45 4.1.1 DOS Range (0000_0000h - 0009_FFFFh)...................................................47 4.1.2 Legacy Video Area (000A_0000h to 000B_FFFFh)........................................47 4.1.2.1 Compatible SMRAM Address Range (000A_0000h to 000B_FFFFh) ...47 4.1.2.2 Monochrome Adapter (MDA) Range (000B_0000h to 000B_7FFFh)...47 4.1.3 Expansion Area (000C_0000h to 000D_FFFFh) ...........................................47 4.1.4 Extended System BIOS Area (000E_0000h to 000E_FFFFh) ..........................48 4.1.5 System BIOS Area (000F_0000h to 000F_FFFFh) ........................................48 4.1.6 Programmable Attribute Map (PAM) Memory Area Details .............................49 4.2 Main Memory Address Range (1 MB to TOLUD) ......................................................49 4.2.1 ISA Hole (15 MB to 16 MB) ......................................................................50 4.2.2 Top Segment (TSEG) ..............................................................................51 4.2.3 Pre-allocated Memory..............................................................................51 4.3 PCI Memory Address Range (TOLUD to 4 GB) ........................................................52 4.3.1 APIC Configuration Space (FEC0_0000h to FECF_FFFFh) ..............................54 4.3.2 HSEG (FEDA_0000h to FEDB_FFFFh) .........................................................54 4.3.3 FSB Interrupt Memory Space (FEE0_0000 to FEEF_FFFF) .............................54 4.3.4 High BIOS Area ......................................................................................54 4.4 Main Memory Address Space (4 GB to TOUUD) ......................................................55 4.4.1 Memory Re-Map Background ....................................................................55 4.4.2 Memory Remapping (or Reclaiming) ..........................................................56 4.5 PCI Express Configuration Address Space..............................................................56 4.5.1 PCI Express Graphics Attach ....................................................................56 4.5.2 Graphics Aperture...................................................................................56 4.6 Graphics Memory Address Ranges........................................................................57 4.6.1 Graphics Register Ranges ........................................................................57 4.6.2 I/O Mapped Access to Device 2 MMIO Space ..............................................57 4.7 System Management Mode (SMM) .......................................................................59 4.7.1 SMM Space Definition ..............................................................................59 4.8 SMM Space Restrictions ......................................................................................60 4.8.1 SMM Space Combinations ........................................................................60 4.8.2 SMM Control Combinations.......................................................................60 4.8.3 SMM Space Decode and Transaction Handling.............................................61 4.8.4 Processor WB Transaction to an Enabled SMM Address Space .......................61 4.9 Memory Shadowing............................................................................................61 4.10 I/O Address Space .............................................................................................61 4.10.1 PCI Express I/O Address Mapping .............................................................62 4 Datasheet 4.11 (G)MCH Decode Rules and Cross-Bridge Address Mapping....................................... 63 4.11.1 Legacy VGA and I/O Range Decode Rules .................................................. 63 5 System Memory Controller ...................................................................................... 65 5.1 Functional Overview .......................................................................................... 65 5.2 Memory Channel Access Modes ........................................................................... 65 5.2.1 Dual Channel Interleaved Mode ................................................................ 66 5.2.1.1 Intel(R) Flex Memory Technology (Dual Channel Interleaved Mode with Unequal Memory Population) ...................................................... 66 5.2.2 Dual Channel Non-Interleaved Mode ......................................................... 67 5.3 DRAM Technologies and Organization................................................................... 67 5.3.1 Rules for Populating SO-DIMM Slots.......................................................... 68 5.3.2 Pin Connectivity for Dual Channel Modes ................................................... 68 5.4 DRAM Clock Generation...................................................................................... 68 5.5 DDR2 On Die Termination................................................................................... 68 5.6 DRAM Power Management .................................................................................. 69 5.6.1 Self Refresh Entry and Exit Operation........................................................ 69 5.6.2 Dynamic Power Down Operation............................................................... 69 5.6.3 DRAM I/O Power Management ................................................................. 69 5.7 System Memory Throttling.................................................................................. 70 6 PCI Express Based External Graphics ...................................................................... 71 6.1 PCI Express Architecture .................................................................................... 71 6.1.1 Transaction Layer................................................................................... 71 6.1.2 Data Link Layer...................................................................................... 71 6.1.3 Physical Layer........................................................................................ 71 6.2 PCI Express Configuration Mechanism .................................................................. 72 6.3 Serial Digital Video Output (SDVO) ...................................................................... 73 6.3.1 SDVO Capabilities................................................................................... 73 6.3.2 Concurrent SDVO/PCI Express Operation ................................................... 74 6.3.2.1 SDVO Signal Mapping ................................................................ 75 6.4 SDVO Modes..................................................................................................... 76 7 Integrated Graphics Controller ................................................................................ 79 7.1 Graphics Processing........................................................................................... 80 7.1.1 3D Graphics Pipeline ............................................................................... 80 7.1.2 3D Engine ............................................................................................. 80 7.1.2.1 Setup Engine............................................................................ 80 7.1.2.2 Rasterizer ................................................................................ 81 7.1.2.3 Texture Engine ......................................................................... 82 7.1.3 2D Engine ............................................................................................. 84 7.1.3.1 Video Graphics Array Registers ................................................... 85 7.1.3.2 Logical 128-Bit Fixed BLT and 256 Fill Engine ............................... 85 7.1.3.3 HW Rotation............................................................................. 85 7.1.4 Video Engine ......................................................................................... 86 7.1.4.1 Dynamic Video Memory Technology (DVMT 4.0)............................ 86 7.1.4.2 Intel(R) Clear Video Technology ................................................... 86 7.1.4.3 Sub-Picture Support .................................................................. 90 8 Graphics Display Interfaces ..................................................................................... 91 8.1 Display Overview .............................................................................................. 91 8.2 Display Planes .................................................................................................. 91 8.2.1 DDC (Display Data Channel) .................................................................... 92 8.2.1.1 Source/Destination Color Keying/ChromaKeying............................ 92 8.2.1.2 Gamma Correction .................................................................... 92 8.3 Display Pipes .................................................................................................... 92 8.3.1 Clock Generator Units (DPLL)................................................................... 92 Datasheet 5 8.4 8.5 Display Ports.....................................................................................................92 8.4.1 Analog Display Port CRT ..........................................................................93 8.4.1.1 Integrated RAMDAC...................................................................94 8.4.1.2 Sync Signals.............................................................................94 8.4.2 LVDS Display Port ...................................................................................94 8.4.2.1 LVDS Interface Signals...............................................................95 8.4.2.2 LVDS Data Pairs and Clock Pairs..................................................95 8.4.2.3 LVDS Pair States .......................................................................96 8.4.2.4 Single Channel versus Dual Channel Mode ....................................96 8.4.2.5 LVDS Channel Skew ..................................................................96 8.4.2.6 LVDS PLL .................................................................................96 8.4.2.7 Panel Power Sequencing.............................................................97 8.4.3 SDVO Digital Display Port ........................................................................98 8.4.3.1 SDVO ......................................................................................98 8.4.3.2 SDVO LVDS ..............................................................................98 8.4.3.3 SDVO DVI ................................................................................98 8.4.3.4 SDVO Analog TV-Out .................................................................98 8.4.3.5 SDVO Analog CRT .....................................................................99 8.4.3.6 SDVO HDMI..............................................................................99 8.4.3.7 External CE Type Devices ...........................................................99 Multiple Display Configurations .......................................................................... 100 9 Power Management ............................................................................................... 101 9.1 Overview ........................................................................................................ 101 9.2 ACPI 3.0 Support............................................................................................. 102 9.2.1 System States...................................................................................... 102 9.2.2 Processor States................................................................................... 102 9.2.3 Integrated Graphics Display Device States ............................................... 102 9.2.4 Integrated Graphics Display Adapter States.............................................. 102 9.3 (G)MCH Interface Power Management State Support ............................................ 103 9.3.1 PCI Express Link States ......................................................................... 103 9.3.1.1 Dynamic Power Management on I/O .......................................... 103 9.3.2 DMI States .......................................................................................... 103 9.3.3 System Memory States.......................................................................... 103 9.3.4 SDVO.................................................................................................. 103 9.3.4.1 Dynamic Power Management on I/O .......................................... 103 9.4 Intel Management Engine Power Management State Support ................................. 104 9.5 (G)MCH State Combinations .............................................................................. 104 9.6 Additional Power Management Features .............................................................. 105 9.6.1 Front Side Bus Interface ........................................................................ 105 9.6.1.1 Intel Dynamic Front Side Bus Frequency Switching ...................... 105 9.6.1.2 H_DPWR# .............................................................................. 106 9.6.1.3 CPU Sleep (H_CPUSLP#) Signal Definition .................................. 106 9.6.2 PCI Express Graphics/DMI interfaces ....................................................... 106 9.6.2.1 CLKREQ# - Mode of Operation .................................................. 106 9.6.3 System Memory Interface ...................................................................... 106 9.6.3.1 Intel Rapid Memory Power Management (Intel RMPM) .................. 106 9.6.3.2 Disabling Unused System Memory Outputs ................................. 107 9.6.3.3 Dynamic Power Down of Memory............................................... 107 9.6.4 Integrated Graphics .............................................................................. 107 9.6.4.1 Intel Display Power Saving Technology 3.0 ................................. 107 9.6.4.2 Intel Smart 2D Display Technology ............................................ 108 9.6.4.3 Dynamic Display Power Optimization* (D2PO) Panel Support ........ 108 9.6.4.4 Intel Automatic Display Brightness ............................................ 108 9.6.4.5 Intel Display Refresh Rate Switching .......................................... 108 10 Absolute Maximum Ratings .................................................................................... 109 6 Datasheet 10.1 10.2 Power Characteristics....................................................................................... 111 Thermal Characteristics.................................................................................... 114 11 Thermal Management ............................................................................................ 115 11.1 Internal Thermal Sensors ................................................................................. 115 11.1.1 Thermal Sensor Accuracy ...................................................................... 116 11.1.2 Sample Programming Model .................................................................. 116 11.1.2.1 Setting Trip Point for Hot Temperature and Generating an SERR Interrupt ............................................................................... 116 11.1.2.2 Temperature Rising above the Hot Trip Point .............................. 116 11.1.2.3 Determining the Current Temperature as Indicated by the Thermometer ......................................................................... 116 11.1.3 Hysteresis Operation............................................................................. 117 11.2 External Thermal Sensor Interface..................................................................... 117 11.3 Thermal Throttling Options ............................................................................... 118 11.4 THERMTRIP# Operation ................................................................................... 118 12 DC Characteristics ................................................................................................. 119 12.1 General DC Characteristics ............................................................................... 122 12.2 CRT DAC DC Characteristics.............................................................................. 128 12.3 TV DAC DC Characteristics................................................................................ 129 13 Clocking ................................................................................................................ 131 13.1 Overview ....................................................................................................... 131 13.2 (G)MCH Reference Clocks ................................................................................. 131 13.3 Host/Memory/Graphics Core Clock Frequency Support.......................................... 132 14 (G)MCH Strapping Configuration ........................................................................... 133 15 Ballout and Package Information........................................................................... 135 15.1 (G)MCH Ballout Diagrams................................................................................. 135 15.2 Ball List (Listed by Interface) ............................................................................ 139 15.2.1 Analog TV-out...................................................................................... 139 15.2.2 CRT DAC ............................................................................................. 139 15.2.3 DDC and GMBus................................................................................... 139 15.2.4 DMI.................................................................................................... 139 15.2.5 Host Interface...................................................................................... 140 15.2.6 LVDS .................................................................................................. 141 15.2.7 Intel(R) Management Engine Interface...................................................... 141 15.2.8 Memory Interface ................................................................................. 141 15.2.9 No Connects ........................................................................................ 144 15.2.10PCI Express Based Graphics................................................................... 144 15.2.11PLL..................................................................................................... 145 15.2.12Power and Ground................................................................................ 145 15.2.13Reserved and Test................................................................................ 151 15.2.14Strappings .......................................................................................... 151 15.2.15Reset and Miscellaneous........................................................................ 152 15.3 Ball List (Listed by Ball).................................................................................... 152 15.4 Package ......................................................................................................... 163 16 17 18 19 20 21 22 (G)MCH Register Description ................................................................................. 165 (G)MCH Configuration Process and Registers ........................................................ 167 Host Bridge Device 0 Configuration Registers (D0:F0) ........................................... 181 Device 0 Memory Mapped I/O Register.................................................................. 219 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) .......................... 343 Internal Graphics Device 2 Configuration Register (D2:F0-F1) .............................. 401 Intel(R) Management Engine Subsystem PCI Device 3............................................. 447 Datasheet 7 Figures 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 8 Intel(R) Centrino(R) Duo Processor Technology with Mobile Intel(R) 965 Express Chipset Family (G)MCH.........................................................................................................11 System Address Ranges ............................................................................................45 DOS Legacy Address Range .......................................................................................46 Main Memory Address Range (0 to 4 GB) .....................................................................50 PCI Memory Address Range .......................................................................................53 Graphics Register Memory and I/O Map .......................................................................58 Intel(R) Flex Memory Technology Operation...................................................................66 System Memory Styles..............................................................................................67 PCI Express Related Register Structures in (G)MCH.......................................................72 SDVO Conceptual Block Diagram ................................................................................73 SDVO/PCI Express Non-Reversed Configurations ..........................................................75 SDVO/PCI Express* Reversed Configurations ...............................................................75 (G)MCH Graphics Controller Block Diagram ..................................................................79 MPEG-2 Decode Stage...............................................................................................87 WMV9 Decode Stage.................................................................................................88 Mobile Intel Gx965 Express Chipset Display Block Diagram ............................................91 LVDS Signals and Swing Voltage ................................................................................95 LVDS Clock and Data Relationship ..............................................................................96 Panel Power Sequencing............................................................................................97 Platform External Thermal Sensor............................................................................. 117 Ballout Diagram (Top View) Upper Left Quadrant ........................................................ 135 Ballout Diagram (Top View) Upper Right Quadrant ...................................................... 136 Ballout Diagram (Top View) Lower Left Quadrant ........................................................ 137 Ballout Diagram (Top View) Lower Right Quadrant ...................................................... 138 (G)MCH Mechanical Drawing .................................................................................... 164 Datasheet Tables 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 SDVO and PCI Express Based Graphics Port Signal Mapping........................................... 28 Expansion Area Memory Segments ............................................................................. 48 Extended System BIOS Area Memory Segments........................................................... 48 System BIOS Area Memory Segments......................................................................... 48 Pre-allocated Memory Example for 512-MB DRAM, 64-MB VGA, and 1-MB TSEG ............... 51 SMM Space Definition Summary................................................................................. 59 SMM Space Table ..................................................................................................... 60 SMM Control Table ................................................................................................... 61 System Memory Organization Support for DDR2........................................................... 65 DDR2 Dual Channel Pin Connectivity........................................................................... 68 DDR2 Single Channel Pin Connectivity ........................................................................ 68 Concurrent SDVO / PCI Express* Configuration Strap Controls ....................................... 74 Configuration-wise Mapping of SDVO Signals on the PCI Express Interface ...................... 76 Display Port Characteristics ....................................................................................... 93 Analog Port Characteristics ........................................................................................ 94 Panel Power Sequencing Timing Parameters ................................................................ 98 G, S and C State Combinations ................................................................................ 105 D, S, and C State Combinations ............................................................................... 105 Targeted Memory State Conditions ........................................................................... 107 Absolute Maximum Ratings ..................................................................................... 109 Mobile Intel 965 Express Chipset Family Thermal Design Power Numbers ...................... 111 Power Characteristics ............................................................................................. 111 DDR2 (533 MTs/667 MTs) Power Characteristics ........................................................ 113 VCC Auxiliary Rail Power Characteristics .................................................................... 114 Mobile Intel 965 Express Chipset Family Package Thermal Resistance ........................... 114 Trip Points ............................................................................................................ 115 Signal Groups........................................................................................................ 119 DC Characteristics.................................................................................................. 122 CRT DAC DC Characteristics: Functional Operating Range (VCCADAC = 3.3 V 5%)........................................................................................ 128 TV DAC DC Characteristics: Functional Operating Range (VCCATVDAC [A,B,C] = 3.3 V 5%) ......................................................................... 129 Host/Memory/Graphics Clock Frequency Support for 1.05-V Core Voltage for the Mobile Intel GM965 and GL960 Express Chipsets.................................................................. 132 Host/Memory/Graphics Clock Frequency Support for 1.05-V Core Voltage for the Mobile Intel GM965/GM965 (mini-note)/GM965 (sub-note), GL960 and PM965 Express Chipsets 132 (G)MCH Strapping Signals and Configuration ............................................................. 133 Datasheet 9 Revision History Revision Number Description Revision Date 001 Initial Release May 2007 002 Changes made to disclaimer page June 2007 003 * Chapter 1 -- Updated Figure 1 -- Added Section 1.3 - Mobile Intel(R) GL960 Express Chipset Feature Support -- Added Section 1.4 - Mobile Intel(R) GME965 Express Chipset Feature Support -- Added Section 1.5 - Mobile Intel(R) GLE960 Express Chipset Feature Support -- Section 1.1.6 - Replaced "Support for Intel 82801 GBM/GHM (base variant) only" with "Support for Intel 82801 HEM\HBM (base variant) only" -- Section 18.1 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 18.1.2 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 20.1 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 20.1.2 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 21.1 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 21.1.2 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 21.2 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 21.2.2 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 22.1 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 22.1.1 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 22.2 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 22.2.1 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 22.3 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 22.3.1 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 22.4 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset -- Section 22.4.1 - Added notes to Host Bridge Device ID for support for Mobile Intel GME965 and GLE960 Express Chipset June 2007 10 Datasheet Introduction 1 Introduction The Mobile Intel(R) 965 Express Chipset family is designed for use in Intel's next generation Intel(R) Centrino(R) Duo processor technology. Figure 1 provides a system block diagram. Figure 1. Intel(R) Centrino(R) Duo Processor Technology with Mobile Intel(R) 965 Express Chipset Family (G)MCH Intel(R) CoreTM2 Duo Processor for Mobile Intel(R) 965 Express Chipset Family Analog TV FSB 533/800 MHz Analog CRT 2 SDVO Ports OR Discrete Graphics PCI Express x16 Mobile Intel 965 Express Chipset Family LVDS Flat Panel DDR2 SO-DIMMs 533/667 MHz Intel(R) Management Engine DMI (x2/x4) PCI Express PCI Express PCI Express Intel(R) Turbo Memory 6 PCI Express* x1 Ports Intel(R) Management Engine PCI Express* 3 Ports 1 Port Intel(R) 82801 HEM/HBM PCI Express Intel(R) Wireless WiFi Link 4965AGN Controller Link 0 PATA Intel(R) HD Audio Intel(R) 82566MM Gigabit Network Connection GLCI SPI 10/100 LCI LPC LPC 10 Ports USB 2.0 Controller Link 1 LPC PCI Power Management Datasheet Serial ATA SPI Flash FWH TPM 1.2 SIO PCI SMBUS 2.0 GPIO 11 Introduction The Mobile Intel 965 Express Chipset family (also referred to as (G)MCH) can be enabled to support either integrated graphics or external graphics. When external graphics is enabled, the x16 PCI Express* Graphics attach port is utilized, and the integrated graphics ports are disabled. 1.1 Mobile Intel(R) PM965 Express Chipset Feature Support 1.1.1 Processor Support * Intel(R) CoreTM2 Duo Mobile Processor for Mobile Intel 965 Express Chipset Family * 533-MHz and 800-MHz FSB support * Source synchronous double-pumped (2x) address * Source synchronous quad-pumped (4x) data * Intel(R) Dynamic Front Side Bus Frequency Switching * Support for DBI (Data Bus Inversion) * Support for MSI (Message Signaled Interrupt) * 36-bit interface to addressing, allowing the CPU to access the entire 64 GB of the (G)MCH memory address space * 12-deep, in-order queue to pipeline FSB commands * AGTL+ bus driver with integrated AGTL termination resistors 1.1.2 System Memory Support * Supports dual-channel DDR2 SDRAM * One SO-DIMM connector (or memory module) per channel * Two memory channel configurations supported -- Dual channel interleaved -- Dual channel asymmetric * Maximum memory supported: 4 GB * Intel(R) Flex Memory Technology support * 64-bit wide per channel * Support for DDR2 at 667 MHz and 533 MHz * 256-Mb, 512-Mb, and 1-Gb memory technologies supported * Support for x8 and x16 devices * Support for DDR2 On-Die Termination (ODT) * Supports partial writes to memory using data mask signals (DM) * Dynamic rank power-down * No support for Fast Chip Select mode * No support for ECC 12 Datasheet Introduction 1.1.3 Discrete Graphics using PCI Express* Graphics Attach Port * One 16-lane (x16) PCI Express port for external PCI Express-based graphics card -- May also be configured as a PCI Express x1 port 1.1.4 Direct Management Interface * Chip-to-chip interface between (G)MCH and 82801 GBM/GHM * Configurable as x2 or x4 DMI lanes * DMI x2 lanes reversed is not supported * DMI polarity inversion is supported * 2-GB/s (1-GB/s each direction) point-to-point interface to Intel(R) 82801 GBM/GHM * 32-bit downstream address * DMI asynchronously coupled to core * APIC and MSI interrupt messaging support * Supports SMI, SCI and SERR error indication * Legacy support for ISA regime protocol (PHOLD/PHOLDA) required for parallel port DMA, floppy drive, and LPC bus masters 1.1.5 Power Management * Supports ACPI 3.0 * S States: S0, S3, S4, S5 * C States: C0, C1, C1E, C2, C2E, C3, C4, C4E and Intel(R) Enhanced Deeper Sleep states * M States: M0, M1, M-off * PCI Express Link States: L0, L0s, L1, L2/L3 ready, L3 * H_CPUSLP# output * H_DPWR# support * Intel(R) Rapid Memory Power Management (Intel(R) RMPM) * Intel(R) Dynamic Front Side Bus Frequency Switching 1.1.6 Security and Manageability (Intel(R) Active Management Technology) * Remote Asset Management * Remote Diagnosis and Repair * Remote Agent Presence * Wireless OOB Management * System Defense Network Isolation * Mobile Power Management Policies * Third-party Non-Volatile Storage * Intel(R) Active Management Technology (Intel(R) AMT) 2.5 with both wired and wireless LAN support Datasheet 13 Introduction * Controller Link interface to Intel 82801 HEM/HBM for extended manageability functionality 1.1.7 Package * FCBGA * Ball Count: 1299 balls * Package Size: 35 mm x 35 mm * Ball pitch: Variable pitch; 31.5-mil minimum pitch 1.1.8 Intel(R) Stable Image Platform Program Supported 1.2 Mobile Intel(R) GM965 Express Chipset Feature Support All features supported by Mobile Intel PM965 Express Chipset are supported by Mobile Intel(R) GM965 Chipset unless otherwise noted below. Additional features are also listed. 1.2.1 PCI Express Graphics Attach Port * One 16-lane (x16) PCI Express port for external PCI Express-based graphics card -- May also be configured as a PCI Express x1 port for video capture * Lane reversal is supported * Polarity Inversion is supported 1.2.2 Integrated Graphics * Mobile Intel(R) Graphics Media Accelerator X3100 (Mobile Intel(R) GMA X3100) * Supports a QXGA maximum resolution of 2048 x 1536 at 60-Hz, 32-bpp reduced blanking timing (driver limited) * 500-MHz core render clock at 1.05-V core voltage * Supports Analog TV-Out, LVDS, Analog CRT and SDVO * Intel(R) Smart 2D Display Technology (Intel(R) S2DDT) * Video Capture via x1 concurrent PCI Express port * Dynamic Video Memory Technology (DVMT 4.0; 384 Maximum) * Intel(R) Clear Video Technology -- MPEG-2 Hardware Acceleration -- WMV9 Hardware Acceleration -- ProcAmp -- Advanced Pixel Adaptive De-interlacing -- Sharpness Enhancement -- De-noise Filter -- High Quality Scaling 14 Datasheet Introduction -- Film Mode Detection and Correction -- Intel(R) TV Wizard * Microsoft DirectX* 9 * Intermediate Z * SGI OpenGL* 1.5 * Hardware Pixel Shader 3.0 * HW rotation Note: Indicated maximum resolutions may not be supported on all ports or in all dual display configurations. 1.2.2.1 Analog CRT * Integrated 300-MHz RAMDAC * For supported resolutions, refer to the OMP tool * Support for CRT hot plug 1.2.2.2 Dual Channel LVDS * For supported resolutions, refer to the OMP tool * 25-112 MHz single/dual channel -- Single channel LVDS interface support: 1 x 18-bpp OR 1 x 24-bpp (Type 1 only), compatible with VESA LVDS color mapping) -- Dual channel LVDS interface support: 2 x 18-bpp panel support or 2 x 24-bpp panel (Type 1 only) -- TFT panel type supported * Pixel dithering for 18-bit TFT panel to emulate 24-bpp true color displays * Panel Fitting, Panning, and Center mode supported * Standard Panel Working Group (SPWG) v.3.5 specification compliant * Spread spectrum clocking supported * Panel power sequencing support * Integrated PWM interface for LCD backlight inverter control 1.2.2.3 Analog TV-Out * Three integrated 10-bit DACs * MacroVision* support * Overscaling * NTSC/PAL * Component, S-Video, TV D connector, and Composite Output Interfaces * SDTV 480i support * EDTV 480p support * HDTV 720p, 1080i support * True HDTV 1080p support The Mobile Intel GM965 and GL960 Express chipsets support the equivalent PAL resolutions. Datasheet 15 Introduction 1.2.2.4 SDVO Ports * Two SDVO ports supported -- SDVO pins are muxed onto the PCI Express Graphics attach port pins -- DVI 1.0 support for External Digital Monitor -- HDCP 1.2 support -- Display Hot Plug support -- Second CRT support * Supports appropriate external SDVO components (HDMI, DVI, LVDS, Analog TVOut, Analog CRT) * I2C* channel provided for control * SDTV 480i support * EDTV 480p support * HDTV 720p, 1080i support * True HDTV 1080p support The Mobile Intel GM965 and GL960 Express chipsets supports the equivalent PAL resolutions. 1.2.3 Power Management * Graphics Display Adapter States: D0, D3 * Intel(R) Display Power Saving Technology (Intel(R) DPST) 3.0 * Intel(R) Smart 2D Display Technology (Intel(R) S2DDT) * Dynamic Display Power Optimization* (D2PO) Panel Support * Intel(R) Automatic Display Brightness * Intel(R) Display Refresh Rate Switching 1.2.4 Intel Stable Image Platform Program * Supported 1.3 Mobile Intel(R) GL960 Express Chipset Feature Support All features supported by Mobile Intel GM965 Express Chipset are supported by Mobile Intel(R) GL960 Express Chipset unless otherwise noted below. Additional features are also listed. 1.3.1 Processor Support * Intel(R) Celeron(R) processor * 533-MHz FSB support 16 Datasheet Introduction 1.3.2 System Memory Support * Support for DDR2 at 533 MHz only * Maximum memory supported: 2 GB 1.3.3 PCI Express Graphics Attach Port * PCI Express* Graphics is disabled 1.3.4 Integrated Graphics * 400-MHz core render clock at 1.05-V core voltage 1.3.5 ICH Support * Support for Intel 82801 HBM (base variant) only 1.3.6 Power Management All Power Management features supported by Mobile Intel PM965 Express Chipset are supported by Mobile Intel GL960 Express Chipset unless otherwise noted below. * Intel RMPM is not supported * Intel Dynamic Front Side Bus Frequency Switching is not supported 1.3.7 Intel Advanced Management Technology * Not supported 1.3.8 Intel Stable Image Platform Program * Not supported 1.4 Mobile Intel(R) GME965 Express Chipset Feature Support All features supported by Mobile Intel GM965 Express Chipset shall be supported by Mobile Intel GME965 Express Chipset unless otherwise noted below. Additional features are also listed below. 1.4.1 Integrated Graphics 1.4.1.1 Analog TV-Out * No Macrovision* support Datasheet 17 Introduction 1.5 Mobile Intel(R) GLE960 Express Chipset Feature Support All features supported by Mobile Intel GL960 Express Chipset shall be supported by Mobile Intel GLE960 Express Chipset unless otherwise noted below. Additional features are also listed below. 1.5.1 Integrated Graphics 1.5.1.1 Analog TV-Out * No Macrovision support 1.6 Terminology (Sheet 1 of 2) Term ACPI Advanced Configuration and Power Interface CPU Central Processing Unit or processor CRT Cathode Ray Tube DBI Dynamic Bus inversion DDR2 Second generation Double Data Rate SDRAM memory technology. DMI Direct Media Interface. The chip-to-chip interconnect between the chipset and the 82801 GBM/GHM. It is an Intel proprietary interface. DVI* Digital Visual Interface is the interface specified by the DDWG (Digital Display Working Group) DVI Spec. Rev. 1.0. ECC Error Correction Code FSB Front Side Bus. Connection between chipset and the processor. Also known as the Host interface. (G)MCH Graphics Memory Controller Hub HDMI High Definition Multimedia Interface - HDMI supports standard, enhanced, or high-definition video, plus multi-channel digital audio on a single cable. It transmits all ATSC HDTV standards and supports 8-channel digital audio, (additional details available through http://www.hdmi.org). Host This term is used synonymously with processor. 2 18 Description I C Inter-IC (a two wire serial bus created by Philips). iDCT Inverse Discrete Cosine Transform. Intel(R) 82801 HEM\HBM The I/O Controller Hub component that contains the primary PCI interface, LPC interface, USB2, Serial ATA, and other I/O functions. It communicates with the (G)MCH over a proprietary interconnect called DMI. Also referred to as Intel ICH8M throughout the document. INTx An interrupt request signal where X stands for interrupts A,B,C and D. ISIPP Intel(R) Stable Image Platform Program. LCD Liquid Crystal Display LFP Local Flat Panel Datasheet Introduction (Sheet 2 of 2) Term 1.7 Description LVDS Low Voltage Differential Signaling. A high speed, low power data transmission standard used for display connections to LCD panels. NCTF Non-Critical to Function NTSC National Television Standards Committee PAL Phase Alternate Line PWM Pulse Width Modulation Rank A unit of DRAM corresponding four to eight devices in parallel, ignoring ECC. These devices are usually, but not always, mounted on a single side of a SODIMM. SCI System Control Interrupt. Used in ACPI protocol. SDVO Serial Digital Video Out (SDVO). Digital display channel that serially transmits digital display data to an external SDVO device. The SDVO device accepts this serialized format and then translates the data into the appropriate display format (i.e., TMDS, LVDS, TV-Out). This interface is not electrically compatible with the previous digital display channel - DVO. For the (G)MCH, it is multiplexed on a portion of the x16 graphics PCI Express* interface. SDVO Device Third-party codec that utilizes SDVO as an input. May have a variety of output formats, including HDMI, DVI, LVDS, TV-out, etc. TMDS Transition Minimized Differential Signaling. TTM Time to Market VLD Variable Length Decoding VTT Front Side Bus Power Supply (VCCP) x1 A Link or Port with one Physical Lane x16 A Link or Port with sixteen Physical Lanes Reference Documents Document Datasheet Document No./Location Advanced Configuration and Power Interface Specification 3.0 http://www.acpi.info/ PCI Local Bus Specification 3.0 http://www.pcisig.com/specifications PCI Express Specification 1.1 http://www.pcisig.com PCI Express Architecture Mobile Graphics Low Power Addendum to the PCI Express Base Specification Revision 1.0 http://www.pcisig.org Standard Panel Working Group (SPWG) v.3.5 Specification http://www.spwg.org/ Mobile Intel(R) 965 Express Chipset Family Specification Updatehttp://www.intel.com/design/mobile/specupdt/ 316273.htm http://www.intel.com/design/mobile/ specupdt/316273.htm Intel(R) CoreTM2 Duo Processor for Mobile Intel(R) 965 Express Chipset Family Datasheet http://www.intel.com/design/mobile/ datashts/316745.htm 19 Introduction Document 20 Document No./Location Intel(R) CoreTM2 Duo Processor for Mobile Intel(R) 965 Express Chipset Family Specification Update http://www.intel.com/design/mobile/ specupdt/316746.htm. JEDEC Double Data Rate 2 (DDR2) SDRAM Specification http://www.jedec.com DDR2 JEDEC Specification Addendum http://www.intel.com/technology/ memory/#Specs Intel(R) I/O Controller Hub 8 (ICH8) Datasheet www.intel.com/design/chipsets/ datashts/313056.htm Intel(R) I/O Controller Hub 8 (ICH8) Specification Update http://www.intel.com/design/chipsets/ specupdt/313057.htm VESA Specification http://www.vesa.org TIA/EIA-644 Standard http://www.tiaonline.org Digital Visual Interface (DVI) Specification http://www.ddwg.org/downloads.asp Datasheet Signal Description 2 Signal Description This section describes the (G)MCH signals. These signals are arranged in functional groups according to their associated interface. The following notations are used to describe the signal type: Notations I O I/O Signal Type Input pin Output pin Bi-directional Input/Output pin The signal description also includes the type of buffer used for the particular signal: Signal Description AGTL+ Open Drain AGTL+ interface signal. Refer to the AGTL+ I/O Specification for complete details. The (G)MCH integrates AGTL+ termination resistors, and supports VTT from 0.83 V to 1.65 V (including guardbanding). PCI Express* PCI Express interface signals. These signals are compatible with PCI Express 1.1 Signaling Environment AC Specifications. The buffers are not 3.3-V tolerant. Refer to the PCI Express specification. CMOS CMOS buffers. HVCMOS High Voltage CMOS buffers. 3.3-V tolerant LVCMOS Low Voltage CMOS buffers. Vtt tolerant COD CMOS Open Drain buffers. 3.3-V tolerant SSTL-1.8 Stub Series Termination Logic: These are 1.8-V capable buffers. 1.8-V tolerant A Analog reference or output. May be used as a threshold voltage or for buffer compensation. LVDS Low Voltage Differential signal interface Ref Voltage reference signal 1.5-V tolerant Note: System Address and Data Bus signals are logically inverted signals. The actual values are inverted from what appears on the system bus. This must be considered and the addresses and data bus signals must be inverted inside the (G)MCH. All processor control signals follow normal convention: A 0 indicates an active level (low voltage), and a 1 indicates an active level (high voltage). Note: All pins marked RSVD should be left NC. Datasheet 21 Signal Description 2.1 Host Interface Unless otherwise noted, the voltage level for all signals in this interface is tied to the termination voltage of the host bus (VCCP). 2.1.1 Host Interface Signals Signal Name Type Description Host Address Bus: H_A#[35:3] I/O AGTL+ 2X HA#[35:3] connects to the processor address bus. During processor cycles the HA#[35:3] are inputs. The (G)MCH drives HA#[35:3] during snoop cycles on behalf of PCI Express/ Integrated Graphics or ICH8M. HA#[35:3] are transferred at 2x rate. Note that the address is inverted on the processor bus. Host Address Strobe: H_ADS# I/O AGTL+ The system bus owner asserts H_ADS# to indicate the first of two cycles of a request phase. The (G)MCH can also assert this signal for snoop cycles and interrupt messages. Host Address Strobe: H_ADSTB#[1:0] I/O AGTL+ 2X HA#[31:3] connects to the processor address bus. During processor cycles, the source synchronous strobes are used to transfer HA#[35:3] and HREQ#[4:0] at the 2x transfer rate. Strobe Address Bits HADSTB#0 HA#[15:3], HREQ#[4:0] HADSTB#1 HA#[35:16 H_AVREF I Host Reference Voltage: H_DVREF A Reference voltage input for the Data, Address, and Common clock signals of the Host AGTL+ interface. H_BNR# I/O AGTL+ Host Block Next Request: Used to block the current request bus owner from issuing a new request. This signal is used to dynamically control the processor bus pipeline depth. Host Bus Priority Request: H_BPRI# O AGTL+ The (G)MCH is the only Priority Agent on the system bus. It asserts this signal to obtain the ownership of the address bus. This signal has priority over symmetric bus requests and will cause the current symmetric owner to stop issuing new transactions unless the H_LOCK# signal was asserted. Host Bus Request: H_BREQ# I/O AGTL+ The (G)MCH pulls the processor bus H_BREQ# signal low during H_CPURST#. The signal is sampled by the processor on the active-to-inactive transition of H_CPURST#. H_BREQ# should be tri-stated after the hold time requirement has been satisfied. 22 Datasheet Signal Description Signal Name Type Description Host CPU Reset: H_CPURST# O AGTL+ The H_CPURST# pin is an output from the (G)MCH. The (G)MCH asserts H_CPURST# while RSTIN# is asserted and for approximately 1 ms after RSTIN# is deasserted. H_CPURST# allows the processor to begin execution in a known state. Host CPU Sleep: H_CPUSLP# O LVCMOS When asserted in the Stop-Grant state, causes the processor to enter the Sleep state. During Sleep state, the processor stops providing internal clock signals to all units, leaving only the Phase-Locked Loop (PLL) still operating. Processors in this state will not recognize snoops or interrupts. (This is a CMOS type buffer with Vtt - NOT 3.3 volts). Host Data: H_D#[63:0] I/O AGTL+ 4X H_DBSY# I/O AGTL+ H_DEFER# O AGTL+ These signals are connected to the processor data bus. HD#[63:0] are transferred at 4x rate. Note that the data signals are inverted on the processor bus depending on the HDINV#[3:0] signals. Host Data Bus Busy: Used by the data bus owner to hold the data bus for transfers requiring more than one cycle. Host Defer: Signals that the (G)MCH will terminate the transaction currently being snooped with either a deferred response or with a retry response. Host Dynamic Bus Inversion: H_DINV#[3:0] I/O AGTL+ Driven along with the HD[63:0]# signals. Indicates if the associated signals are inverted or not. HDINV[3:0]# are asserted such that the number of data bits driven electrically low (low voltage) within the corresponding 16-bit group never exceeds 8. H_DINV# Data Bits H_DINV#3 H_D#[63:48] H_DINV#2 H_D#[47:32] H_DINV#1 H_D#[31:16] H_DINV#0 H_D#[15:0] Host Data Power: H_DPWR# H_DRDY# Datasheet I/O AGTL+ I/O AGTL+ Used by (G)MCH to indicate that a data return cycle is pending within 2 H_CLK cycles or more. Processor uses this signal during a read-cycle to activate the data input buffers in preparation for H_DRDY# and the related data. Host Data Ready: Asserted for each cycle that data is transferred. 23 Signal Description Signal Name Type Description Host Differential Host Data Strobes: H_DSTBP#[3:0] H_DSTBN#[3:0] I/O AGTL+ 4X The differential source synchronous strobes are used to transfer HD#[63:0] and HDINV#[3:0] at the 4x transfer rate. Strobe Data Bits H_DSTBP#3, H_DSTBN#3 H_D#[63:48], H_DINV#[3] H_DSTBP#2, H_DSTBN#2 H_D#[47:32], H_DINV#[2] H_DSTBP#1, H_DSTBN#1 H_D#[31:16], H_DINV#[1] H_DSTBP#0, H_DSTBN#9 H_D#[15:0], H_DINV#[0] Host Hit: H_HIT# I/O AGTL+ Indicates that a caching agent holds an unmodified version of the requested line. Also, driven in conjunction with H_HITM# by the target to extend the snoop window. Host Hit Modified: H_HITM# I/O AGTL+ Indicates that a caching agent holds a modified version of the requested line and that this agent assumes responsibility for providing the line. Also, driven in conjunction with H_HIT# to extend the snoop window. Host Lock: H_LOCK# I AGTL+ H_RCOMP I/O A All processor bus cycles sampled with the assertion of H_LOCK# and H_ADS#, until the negation of H_LOCK# must be atomic. Host RCOMP: Used to calibrate the Host AGTL+ I/O buffers. Host Request Command: H_REQ#[4:0] I/O AGTL+ 2X Defines the attributes of the request. H_REQ#[4:0] are transferred at 2x rate. Asserted by the requesting agent during both halves of the Request Phase. In the first half the signals define the transaction type to a level of detail that is sufficient to begin a snoop request. In the second half the signals carry additional information to define the complete transaction type. Host Response Status: Indicates the type of response according to the following the table: H_RS#[2:0]Response type H_RS#[2:0] 24 O AGTL+ H_SCOMP I/O H_SCOMP# A 000 Idle state 001 Retry response 010 Deferred response 011 Reserved (not driven by (G)MCH) 100 Hard Failure (not driven by (G)MCH) 101 No data response 110 Implicit Write back 111 Normal data response Host SCOMP: Slew Rate Compensation for the Host Interface. Datasheet Signal Description Signal Name H_SWING H_TRDY# THERMTRIP# Type Description I Host Voltage Swing: A These signals provide reference voltages used by the H_RCOMP circuits. O AGTL+ O AGTL+ Host Target Ready: Indicates that the target of the processor transaction is able to enter the data transfer phase. Connects between the Processor and the Intel ICH8M: Assertion of THERMTRIP# (Thermal Trip) indicates the (G)MCH junction temperature has reached a level beyond which damage may occur. Upon assertion of THERMTRIP#, the (G)MCH will shut off its internal clocks (thus halting program execution) in an attempt to reduce the (G)MCH core junction temperature. To protect (G)MCH, its core voltage (Vcc) must be removed following the assertion of THERMTRIP#. Once activated, THERMTRIP# remains latched until RSTIN# is asserted. While the assertion of the RSTIN# signal will deassert THERMTRIP#, if the (G)MCH's junction temperature remains at or above the trip level, THERMTRIP# will again be asserted. 2.2 DDR2 Memory Interface 2.2.1 DDR2 Memory Channel A Interface Signal Name SA_BS[2:0] SA_CAS# Type O SSTL-1.8 O SSTL-1.8 Description Bank Select: These signals define which banks are selected within each SDRAM rank. CAS Control Signal: Used with SA_RAS# and SA_WE# (along with SA_CS#) to define the SDRAM commands. Data Mask: O SA_DM[7:0] SSTL-1.8 2x I/O SA_DQ[63:0] SSTL-1.8 2x I/O SA_DQS#[7:0] SSTL-1.8 2x Datasheet These signals are used to mask individual bytes of data in the case of a partial write, and to interrupt burst writes. When activated during writes, the corresponding data groups in the SDRAM are masked. There is one SA_DM[7:0] for every data byte lane. Data Bus: DDR2 Channel A data signal interface to the SDRAM data bus. Data Strobe Complements: These are the complementary strobe signals. 25 Signal Description Signal Name Type I/O SA_DQS[7:0] SSTL-1.8 2x SA_MA[14:0] SA_RAS# SA_RCVEN# SA_WE# 2.2.2 O SSTL-1.8 O SSTL-1.8 I SSTL-1.8 O SSTL-1.8 Description Data Strobes: SA_DQS[7:0] and its complement signal group make up a differential strobe pair. The data is captured at the crossing point of SA_DQS[7:0] and its SA_DQS[7:0]# during read and write transactions. Memory Address: These signals are used to provide the multiplexed row and column address to the SDRAM. RAS Control Signal: Used with SA_CAS# and SA_WE# (along with SA_CS#) to define the SDRAM commands. Clock Input: Used to emulate source-synch clocking for reads. Leave as No Connect. Write Enable Control Signal: Used with SA_RAS# and SA_CAS# (along with SA_CS#) to define the SDRAM commands. DDR2 Memory Channel B Interface Signal Name SB_BS[2:0] SB_CAS# Type O SSTL-1.8 O SSTL-1.8 Description Bank Select: These signals define which banks are selected within each SDRAM rank. CAS Control signal: Used with SB_RAS# and SB_WE# (along with SB_CS#) to define the SDRAM commands. Data Mask: O SB_DM[7:0] SSTL-1.8 2x I/O SB_DQ[63:0] SSTL-1.8 2x I/O SB_DQS#[7:0] SSTL-1.8 2x I/O SB_DQS[7:0] SSTL-1.8 2x 26 These signals are used to mask individual bytes of data in the case of a partial write, and to interrupt burst writes. When activated during writes, the corresponding data groups in the SDRAM are masked. There is one SB_DM[7:0] for every data byte lane. Data Bus: DDR2 Channel B data signal interface to the SDRAM data bus. Data Strobe Complements: These are the complementary strobe signals. Data Strobes: SB_DQS[7:0] and its complement signal group make up a differential strobe pair. The data is captured at the crossing point of SB_DQS[7:0] and its SB_DQS[7:0]# during read and write transactions. Datasheet Signal Description Signal Name SB_MA[14:0] SB_RAS# SB_RCVEN# SB_WE# 2.2.3 Type O SSTL-1.8 O SSTL-1.8 I SSTL-1.8 O SSTL-1.8 Description Memory Address: These signals are used to provide the multiplexed row and column address to the SDRAM. RAS Control Signal: Used with SB_CAS# and SB_WE# (along with SB_CS#) to define the SDRAM commands. Clock Input: Used to emulate source-synch clocking for reads. Leave as No Connect. Write Enable Control Signal: Used with SB_RAS# and SB_CAS# (along with SB_CS#) to define the SDRAM commands. DDR2 Memory Common Signals Signal Name Type Description SM_CK#[1:0] O SDRAM Inverted Differential Clock: (2 per SO-DIMM) SM_CK#[4:3] SSTL-1.8 These are the SDRAM Inverted Differential Clock signals. SDRAM Differential Clock: (2 per SO-DIMM) SM_CK[1:0] O SM_CK[4:3] SSTL-1.8 These are the SDRAM Differential Clock signals The crossing of the positive edge of SM_CKx and the negative edge of its complement SM_CKx# are used to sample the command and control signals on the SDRAM. Clock Enable: (1 per Rank): SM_CKE[4:3] and SM_CKE[1:0] is used: SM_CKE[1:0] O SM_CKE[4:3] SSTL-1.8 * to initialize the SDRAMs during power-up, * to power-down SDRAM ranks, * to place all SDRAM ranks into and out of self-refresh during STR. Chip Select: (1 per Rank): SM_CS#[3:0] SM_ODT[3:0] Datasheet O SSTL-1.8 O SSTL-1.8 These signals select particular SDRAM components during the active state. There is one Chip Select for each SDRAM rank. On Die Termination: Active Termination Control. 27 Signal Description 2.2.4 DDR2 Memory Reference and Compensation Signal Name SM_RCOMP SM_RCOMP# SM_RCOMP_VOH SM_RCOMP_VOL SM_VREF 2.3 Type Description I System Memory Impedance Compensation: A Requires pull-up resistor. I System Memory Impedance Compensation: A Requires pull-down resistor. I Swing voltage for pull-up impedance compensation. A I Swing voltage for pull-down impedance compensation. A I System Memory Reference Voltage for all data and data strobe signals (two signals). A PCI Express Based Graphics Interface Signals Unless otherwise specified, these signals are AC coupled. Signal Name PEG_COMPI PEG_COMPO PEG_RX[15:0] PEG_RX#[15:0] PEG_TX[15:0] PEG_TX#[15:0] 2.3.1 Type I Description PCI Express* Graphics Input Current Compensation. A I PCI Express Graphics Output Current and Resistance Compensation. A I PCI Express O PCI Express PCI Express Graphics Receive Differential Pair. PCI Express Graphics Transmit Differential Pair. Serial DVO and PCI Express*-Based Graphics Signal Mapping SDVO and PCI Express interface for graphics architecture are muxed together. Table 1 shows the signal mapping. Table 1. SDVO and PCI Express Based Graphics Port Signal Mapping (Sheet 1 of 2) SDVO Mode SDVOB_RED 28 PCI Express Mode PEG_TXP0 SDVOB_RED# PEG_TXN0 SDVOB_GREEN PEG_TXP1 SDVOB_GREEN# PEG_TXN1 SDVOB_BLUE PEG_TXP2 SDVOB_BLUE# PEG_TXN2 SDVOB_CLK PEG_TXP3 Datasheet Signal Description Table 1. SDVO and PCI Express Based Graphics Port Signal Mapping (Sheet 2 of 2) SDVO Mode 2.4 SDVOB_CLK# PEG_TXN3 SDVOC_RED PEG_TXP4 SDVOC_RED# PEG_TXN4 SDVOC_GREEN PEG_TXP5 SDVOC_GREEN# PEG_TXN5 SDVOC_BLUE PEG_TXP6 SDVOC_BLUE# PEG_TXN6 SDVOC_CLK PEG_TXP7 SDVOC_CLK# PEG_TXN7 SDVO_TV_CLKIN PEG_RXP0 SDVO_TV_CLKIN# PEG_RXN0 SDVO_INT PEG_RXP1 SDVO_INT# PEG_RXN1 SDVO_FLD_STALL PEG_RXP2 SDVO_FLD_STALL# PEG_RXN2 DMI - (G)MCH to ICH Serial Interface Signal Name DMI_RXN[3:0] DMI_RXP[3:0] DMI_TXN[3:0] DMI_TXP[3:0] Datasheet PCI Express Mode Type I PCI Express O PCI Express Description DMI input from ICH: Direct Media Interface receive differential pair. DMI output to ICH: Direct Media Interface transmit differential pair. 29 Signal Description 2.5 Integrated Graphics Interface Signals 2.5.1 CRT DAC Signals Signal Name CRT_BLUE CRT_BLUE# CRT_GREEN CRT_GREEN# CRT_HSYNC CRT_RED CRT_RED# Type O A O A O A O A O HVCMOS O A O A Description BLUE Analog Video Output: This signal is a CRT Analog video output from the internal color palette DAC. BLUE# Analog Output: This signal is an analog video output from the internal color palette DAC. This signal is used to provide noise immunity. GREEN Analog Video Output: This signal is a CRT Analog video output from the internal color palette DAC. GREEN# Analog Output: This signal is an analog video output from the internal color palette DAC. This signal is used to provide noise immunity. CRT Horizontal Synchronization: This signal is used as the horizontal sync (polarity is programmable) or "sync interval". RED Analog Video Output: This signal is a CRT Analog video output from the internal color palette DAC. RED# Analog Output: This signal is an analog video output from the internal color palette DAC. This signal is used to provide noise immunity. Resistor Set and TV Reference Current: CRT_TVO_IREF CRT_VSYNC 30 O A O HVCMOS Set point resistor for the internal color palette DAC and TV reference current. A 1.3 k 0.5% resistor is required between CRT_TVO_IREF and motherboard ground. CRT Vertical Synchronization: This signal is used as the vertical sync (polarity is programmable). Datasheet Signal Description 2.5.2 Analog TV-out Signals Signal Name Type TV_DCONSEL[1: 0] O HVCMOS Description TV D-connector Select: Selects appropriate full-voltage discernment signals for TV-out D-connector. TVDAC Channel A Output: TVA_DAC O A Can map to any one of the following: * Composite Video, Blank, and Sync (CVBS) * Component Pb TVA_RTN O Current Return for TV DAC Channel A: A Connect to ground on board. TVDAC Channel B Output: TVB_DAC O A Can map to any one of the following: Svideo - Y Component Y TVB_RTN O Current Return for TV DAC Channel B: A Connect to ground on board. TVDAC Channel C Output: TVC_DAC O A Can map to any one of the following: Svideo - C Component Pr TVC_RTN Datasheet O Current Return for TV DAC Channel C: A Connect to ground on board. 31 Signal Description 2.5.3 LVDS Signals Signal Name Type Description LDVS Channel A LVDSA_CLK LVDSA_CLK# LVDSA_DATA#[3:0] LVDSA_DATA[3:0] O LVDS O LVDS O LVDS O LVDS LVDS Channel A differential clock output - positive LVDS Channel A differential clock output - negative LVDS Channel A differential data output - negative LVDS Channel A differential data output - positive LDVS Channel B LVDSB_CLK LVDSB_CLK# LVDSB_DATA#[3:0] LVDSB_DATA[3:0] O LVDS O LVDS O LVDS O LVDS LVDS Channel B differential clock output - positive LVDS Channel B differential clock output - negative LVDS Channel B differential data output - negative LVDS Channel B differential data output - positive Lfp Panel Power and Backlight Control L_BKLT_CTRL L_BKLT_EN L_VDD_EN O Panel backlight brightness control HVCMOS Panel brightness control. O LVDS backlight enable HVCMOS O HVCMOS Panel backlight enable control. LVDS panel power enable Panel power control enable control. LVDS Reference Signals LVDS_IBG LVDS_VBG LVDS_VREFH LVDS_VREFL I/O LVDS Reference Current. Ref A pull down resistor of 2.4 k 1% is needed O Reserved A No connect I Reserved Ref I Ref 32 Can be connected to GND or left as No Connect. Reserved Can be connected to GND or left as No Connect. Datasheet Signal Description 2.5.4 Serial DVO Interface All of the pins in this section are multiplexed with the upper eight lanes of the PCI Express interface. Signal Name Type Description SDVO B Interface SDVOB_BLUE SDVOB_BLUE# SDVOB_GREEN SDVOB_GREEN# SDVOB_RED SDVOB_RED# SDVOB_CLK SDVOB_CLK# O PCI Express O PCI Express O PCI Express O PCI Express O PCI Express O PCI Express O PCI Express O PCI Express Serial Digital Video B Blue Data: Multiplexed with PEG_TXP2 Serial Digital Video B Blue Data Complement: Multiplexed with PEG_TXN2 Serial Digital Video B Green Data: Multiplexed with PEG_TXP1 Serial Digital Video B Green Data Complement: Multiplexed with PEG_TXN1 Serial Digital Video B Red Data: Multiplexed with PEG_TXP0 Serial Digital Video B Red Data Complement: Multiplexed with PEG_TXN0 Serial Digital Video B Clock: Multiplexed with PEG_TXP3 Serial Digital Video B Clock Complement: Multiplexed with PEG_TXN3 SDVO C Interface SDVOC_BLUE SDVOC_BLUE# SDVOC_GREEN SDVOC_GREEN# SDVOC_RED SDVOC_RED# SDVOC_CLK SDVOC_CLK# O PCI Express O PCI Express O PCI Express O PCI Express O PCI Express O PCI Express O PCI Express O PCI Express Datasheet Serial Digital Video Channel C Blue: Multiplexed with PEG_TXP6 Serial Digital Video C Blue Complement: Multiplexed with PEG_TXN6 Serial Digital Video C Green: Multiplexed with PEG_TXP5 Serial Digital Video C Green Complement: Multiplexed with PEG_TXN5 Serial Digital Video C Red Data: Multiplexed with PEG_TXP4 Serial Digital Video C Red Complement: Multiplexed with PEG_TXN4 Serial Digital Video C Clock: Multiplexed with PEG_TXP7 Serial Digital Video C Clock Complement: Multiplexed with PEG_TXN7 33 Signal Description Signal Name Type Description SDVO Common Signals SDVO_FLDSTALL SDVO_FLDSTALL# SDVO_INT SDVO_INT# SDVO_TV_CLKIN SDVO_TV_CLKIN# 2.5.5 I PCI Express I PCI Express I PCI Express I PCI Express I PCI Express Serial Digital Video Field Stall: Multiplexed with PEG_RXP2 Serial Digital Video Field Stall Complement: Multiplexed with PEG_RXN2 Serial Digital Video Input Interrupt: Multiplexed with PEG_RXP1 Serial Digital Video Input Interrupt Complement: Multiplexed with PEG_RXN1 Serial Digital Video TVOUT Synchronization Clock: Multiplexed with PEG_RXP0 Serial Digital Video TVOUT Synchronization Clock Complement: Multiplexed with PEG_RXN0 Display Data Channel (DDC) and GMBUS Support Signal Name CRT_DDC_CLK CRT_DDC_DATA L_CTRL_CLK L_CTRL_DATA L_DDC_CLK L_DDC_DATA SDVO_CTRL_CLK SDVO_CTRL_DATA 34 I PCI Express Type I/O COD I/O COD I/O COD I/O COD I/O COD I/O COD I/O COD I/O COD Description CRT DDC clock monitor control support CRT DDC Data monitor control support Control signal (clock) for External SSC clock chip control - optional Control signal (data) for External SSC clock chip control - optional EDID support for flat panel display EDID support for flat panel display Control signal (clock) for SDVO device Control signal (data) for SDVO device Datasheet Signal Description 2.6 Intel(R) Management Engine Interface Signals These signals are the Intel(R) Management Engine Interface between the (G)MCH and the ICH. Signal Name Type CL_CLK Supply Independent CMOS Controller Link Bi Directional Clock CL_DATA Supply Independent CMOS Controller Link Bi Directional Data CL_PWROK CL_RST# I HVCMOS I CMOS I CL_VREF 2.7 Description A Controller Link Power OK Controller Link reset External reference voltage for Controller Link input buffers PLL Signals Signal Name DPLL_REF_CLK DPLL_REF_CLK# DPLL_REF_SSCLK Type I Diff Clk I Diff Clk I Diff Clk DPLL_REF_SSCLK# I Diff Clk Description Display PLLA Differential Clock In: 96-MHz Display PLL Differential Clock In, no SSC support. Display PLLA Differential Clock In Complement: Display PLL Differential Clock In Complement - no SSC support. Display PLLB Differential Clock In: 100-MHz Optional Display PLL Differential Clock In for SSC support - NOTE: Differential Clock input for optional SSC support for LVDS display. Display PLLB Differential Clock In Complement: Optional Display PLL Differential Clock In Complement for SSC support. NOTE: Differential Clock input for optional SSC support for LVDS display. Differential Host Clock In: HPLL_CLK Datasheet I Diff Clk Differential clock input for the Host PLL. Used for phase cancellation for FSB transactions. This clock is used by all of the (G)MCH logic that is in the Host clock domain. Also used to generate core and system memory internal clocks. This is a low voltage differential signal and runs at 1/4 the FSB data rate. 35 Signal Description Signal Name HPLL_CLK# Type I Diff Clk Description Differential Host Clock Input Complement Differential PCI Express Based Graphics/DMI Clock In: PEG_CLK PEG_CLK# 2.8 I Diff Clk I Diff Clk These pins receive a differential 100-MHZ Serial Reference clock from the external clock synthesizer. This clock is used to generate the clocks necessary for the support of PCI Express. Differential PCI Express based Graphics / DMI Clock In complement Reset and Miscellaneous Signals Signal Name CLKREQ# GFX_VID[3:0] GFX_VR_EN ICH_SYNC# PMSYNC# (PM_BM_BUSY#) DPRSLPVR PM_DPRSTP# Type O COD O A O A O HVCMOS I HVCMOS I/O HVCMOS I LVCMOS Description External Clock Request: (G)MCH drives CLK_REQ# to control the PCI Express* differential clock input to itself. Reserved Reserved ICH Synchronization: Asserted to synchronize with ICH on faults. ICH_SYNC# must be connected to ICH8M's MCH_SYNC# signal. (G)MCH Power Management Sync: PMSYNC# is used to indicate some Cx state transition information between ICH and (G)MCH. Deeper Sleep - Voltage Regulator: Deeper Sleep Voltage signal from ICH8M. Deeper Sleep State: Deeper Sleep State signal coming from ICH8M. External Thermal Sensor Input: PM_EXT_TS#[1:0] I HVCMOS If the system temperature reaches a dangerously high value then this signal can be used to trigger the start of system memory throttling. Power OK: PWROK I HVCMOS When asserted, PWROK is an indication to the (G)MCH that (G)MCH clocks have been stable for at least 1 us, and that (G)MCH power supplies have been stable for at least 1 ms. When asserted this signal also ensures that signals coming out of the (G)MCH are stable. This input buffer is 3.3-V tolerant. 36 Datasheet Signal Description Signal Name Type Description Reset In: I RSTIN# HVCMOS When asserted this signal will asynchronously reset the (G)MCH logic. This signal is connected to the PCIRST# output of the ICH8M. This input has a Schmitt trigger to avoid spurious resets. This input buffer is 3.3-V tolerant. I TEST1 HVCMOS I TEST2 HVCMOS NC 2.9 NC Test 1: This signal should be tied to ground. Test 2: This signal should be tied to ground. No Connects: This signals should be left as no connects. Non-Critical to Function (NCTF) Adding non-critical to function (NCTF) solder balls to Intel chipset packages can improve the overall package-to-board solder joint strength and reliability. Ball locations/signal IDs followed with the suffix of NCTF have been designed into the package footprint. Note: In some cases, where board stresses are excessive, these balls may crack partially or completely. However, cracks in the NCTF balls will have no impact to Intel product performance or reliability. 2.10 Power and Ground Voltage Ball Name Description Host 1.05 VTT Host Interface I/O Voltage 1.05 VTTLF These balls are internally connected to power and require a decoupling capacitor. System Memory Datasheet 1.8 VCC_SM I/O Voltage 1.8 VCC_SM_LF These balls are internally connected to power and require a decoupling capacitor. 1.8 VCC_SM_CK Clock I/O Voltage 1.25 VCCA_SM I/O Logic and DLL voltage 1.25 VCCA_SM_CK Clock logic voltage 37 Signal Description Voltage Ball Name Description PCI Express* Based Graphics / DMI VCC_PEG Analog, I/O Logic, and Term Voltage for PCI Express* Based Graphics 3.3 VCCA_PEG_BG Band Gap Voltage for PCI Express Based Graphics Ground VSSA_PEG_BG Band Gap Ground for PCI Express Based Graphics 1.25 VCCA_PEG_PLL Analog PLL Voltage for PCI Express Based Graphics 1.25 VCCD_PEG_PLL Digital PLL Voltage for PCI Express Based Graphics 1.25 VCC_DMI TX Analog and Term Voltage for DMI 1.05 VCC_RXR_DMI Rx and I/O Logic for DMI 1.05 PLL 1.25 VCCA_HPLL Host PLL Analog Supply 1.25 VCCD_HPLL Host PLL Digital Supply 1.25 VCCA_MPLL MPLL Analog circuits 1.25 VCCA_DPLLA Display A PLL power supply 1.25 VCCA_DPLLB Display B PLL power supply High Voltage 3.3 VCC_HV HV buffer power supply CRT 3.3 VCC_SYNC HSYNC/VSYNC power supply 3.3 VCCA_CRT_DAC Analog power supply 1.5 VCCD_QDAC Quiet digital power supply (same as VCCD_QDAC for TV) 1.5 VCCD_CRT Level shifter voltage LVDS 1.8 VCCD_LVDS Digital power supply 1.8 VCC_TX_LVDS I/O power supply 1.8 VCCA_LVDS Analog power supply Ground VSSA_LVDS Analog ground TV 38 1.5 VCCD_TVDAC TV DAC power supply 3.3 VCCA_TVA_DAC TV Out Channel A power supply 3.3 VCCA_TVB_DAC TV Out Channel Bpower supply 3.3 VCCA_TVC_DAC TV Out Channel Cpower supply 1.5 VCCD_QDAC Quiet Digital TV DAC Power Supply (same as VCCDQ_DAC for CRT) 3.3 VCCA_DAC_BG TV DAC Band Gap power (3.3 V) Ground VSSA_DAC_BG TV DAC Band Gap ground Datasheet Signal Description Voltage Ball Name Description Intel(R) Management Engine Interface 1.05 VCC_AXM Controller Link / Intel(R) Management Engine Interface voltage supply Graphics Core 1.05 VCC Core chipset voltage supply 1.05 VCC_AXG Graphics voltage supply 1.25 VCC_AXD Memory voltage supply 1.25 VCC_AXF I/O voltage supply VSS Ground VSS_SCB Sacrificial Corner Balls for improved package reliability. These signals are connected to GND on the chipset package, and can be connected to GND or left as NC on the platform (can be left as test points). Ground NC NOTE: There is no functional impact if these signals are grounded. Datasheet 39 Signal Description 40 Datasheet Host Interface 3 Host Interface 3.1 FSB Source Synchronous Transfers The chipset supports the Intel Core 2 Duo processor subset of the Enhanced Mode Scalable bus. The cache line size is 64 bytes. Source synchronous transfer is used for the address and data signals. The address signals are double pumped and a new address can be generated every other bus clock. At bus clock speeds of 133-MHz, 166-MHz and 200-MHz, address signals run at 266 MT/s, 333 MT/s and 400 MT/s, which amounts to a maximum address queue rate of 64, 83 and 100 Mega-addresses/seconds, respectively. Data signals are quad pumped and an entire 64-B cache line can be transferred in two bus clocks. At 133-MHz, 166-MHz and 200-MHz bus clock, data signals run at 533-MHz, 667-MT/s and 800-MT/s for a maximum bandwidth of 4.3-GB/s, 5.3-GB/s and 6.4-GB/ seconds, respectively. 3.2 FSB IOQ Depth The scalable bus supports up to 12 simultaneous outstanding transactions. The chipset has a 12-deep IOQ. 3.3 FSB OOQ Depth The (G)MCH supports only one outstanding deferred transaction on the FSB. 3.4 FSB AGTL+ Termination The (G)MCH integrates AGTL+ termination resistors on die. 3.5 FSB Dynamic Bus Inversion The (G)MCH supports dynamic bus inversion (DBI) when driving and when receiving data from the processor. DBI limits the number of data signals that are driven to a low voltage on each quad pumped data phase. This decreases the worst-case power consumption of the (G)MCH. H_DINV[3:0]# indicate if the corresponding 16 bits of data are inverted on the bus for each quad pumped data phase: H_DINV#[3:0] Data Bits H_DINV#0 H_D#[15:0] H_DINV#1 H_D#[31:16] H_DINV#2 H_D#[47:32] H_DINV#3 H_D#[63:48] Whenever the processor or the (G)MCH drives data, each 16-bit segment is analyzed. If there are more than eight (out of sixteen) signals driven low on the H_D# bus, a corresponding H_DINV# signal is asserted. As a result, the data is inverted prior to Datasheet 41 Host Interface being driven on the bus. Whenever the processor or the (G)MCH receives data, it monitors H_DINV#[3:0] to determine if the corresponding data segment should be inverted. 3.6 FSB Interrupt Overview The processor supports FSB interrupt delivery. It does not support the APIC serial bus interrupt delivery mechanism. Interrupt-related messages are encoded on the FSB as Interrupt Message Transactions. FSB interrupts may originate from the CPU(s) on the FSB, or from a downstream device on the DMI or PCI Express Graphics Attach. In the latter case, the (G)MCH drives the Interrupt Message Transaction on the FSB. In the IOxAPIC environment, an interrupt is generated from the IOxAPIC to a processor in the form of an upstream memory write. The ICH contains IOxAPICs, and its interrupts are generated as upstream DMI Memory Writes. Furthermore, the PCI Specification and PCI Express Specification define Message Signaled Interrupts (MSIs) that are also in the form of Memory Writes. A PCI device may generate an interrupt as an MSI cycle on its PCI bus instead of asserting a hardware signal to the IOxAPIC. The MSI may be directed to the IOxAPIC. The IOxAPIC in turn generates an interrupt as an upstream DMI Memory Write. Alternatively, the MSI may directly route to the FSB. The target of an MSI is dependent on the address of the interrupt Memory Write. The (G)MCH forwards upstream DMI and PCI Express Graphics Attach low priority Memory Writes to address 0FEEx_xxxxh to the FSB as Interrupt Message Transactions. The (G)MCH also broadcasts EOI cycles generated by a processor downstream to the PCI Express Port and DMI interfaces. 3.7 APIC Cluster Mode Support APIC Cluster mode support is required for backward compatibility with existing software, including various operating systems. For example, beginning with Microsoft Windows* 2000 operating system, there is a mode (boot.ini) that allows an end user to enable the use of cluster addressing support of the APIC. 42 Datasheet System Address Map 4 System Address Map This section focuses on how the memory space is partitioned and what the separate memory regions are used for. I/O address space has simpler mapping and is explained near the end of this section. The chipset supports up to 64 GB of addressable memory space and 64 kB + 3 B of addressable I/O space. There is a programmable memory address space under the 1-MB region, which is divided into regions that can be individually controlled with programmable attributes such as Disable, Read/Write, Write Only, or Read Only. The (G)MCH does not support: * PCI dual address cycle (DAC) mechanism * PCI Express 64-bit prefetchable memory transactions * Any other addressing mechanism that allows addressing of greater than 4 GB on either the DMI or PCI Express interface. * The (G)MCH does not limit DRAM space in hardware. There is no hardware lock to stop someone from inserting more memory than is addressable. It is assumed that all of the compatibility memory ranges reside on the DMI. The exception to this rule is VGA ranges, which may be mapped to PCI Express, DMI, or to the Integrated Graphics Device (IGD). In the absence of more specific references, cycle descriptions referencing PCI should be interpreted as the DMI/PCI, while cycle descriptions referencing PCI Express or IGD are related to the PCI Express bus or the IGD respectively. The (G)MCH does not remap APIC or any other memory spaces above TOLUD (Top of Low Usable DRAM). The TOLUD register is set to the appropriate value by BIOS. The Address Map includes a number of programmable ranges: * Device 0 -- EPBAR - Egress port registers. Necessary for setting up VC1 as an isochronous channel using time-based weighted round-robin arbitration (4-kB window). -- MCHBAR - Memory mapped range for internal (G)MCH registers. -- PCIEXBAR - Flat memory-mapped address spaced to access device configuration registers. This mechanism can be used to access PCI configuration space (0-FFh) and extended configuration space (100h-FFFh) for PCI Express devices. This enhanced configuration access mechanism is defined in the PCI Express specification (64-MB, 128-MB, or 256-MB window). -- DMIBAR -This window is used to access registers associated in the MCH/ICH (DMI) register memory range (4-kB window). -- GGC - (G)MCH graphics control register. Used to select the amount of main memory that is pre-allocated to support the IGD in VGA (non-linear) and Native (linear) modes (0 to 64-MB options). * Device 1, Function 0: -- MBASE1/MLIMIT1 - PCI Express port non-prefetchable memory access window. -- PMBASE1/PMLIMIT1 - PCI Express port prefetchable memory access window. (PMUBASE/PMULIMIT) - are applicable for 36-bit SKUs. -- IOBASE1/IOLIMIT1 - PCI Express port IO access window. Datasheet 43 System Address Map * Device 2, Function 0: -- GTTMMADR - IGD registers integrated graphics translation table location and integrated graphics instruction port (1-MB window). -- IOBAR - I/O access window for integrated graphics. Through this window address/data register pair, using I/O semantics, the IGD and integrated graphics instruction port registers can be accessed. Note this allows accessing the same registers as MMADR. In addition, the IOBAR can be used to issue writes to the GTTMMADR table. -- GMADR - Integrated graphics translation window (256-MB window). * Device 2, Function 1: -- MMADR - Function 1 IGD registers and integrated graphics instruction port (512-kB window). * Device 3, Function 0: -- MEI_MMIBAR - Function 0 Intel(R) Management Engine Interface (MEI) memory mapped registers (16-B window). * Device 3, Function 1: -- MEI2_MMBAR - Function 0 Intel(R) MEI memory mapped registers (16-B window). * Device 3, Function 2: -- PCMDBA- Function 2 I/O space used in Native Mode for the Primary Controller's Command Block (8-B window). -- PCTLBA - Function 2 I/O space used in Native Mode for the Primary Controller's Control Block (4-B window). -- SCMDBA - Function 2 /O space used in Native Mode for the Secondary Controller's Command Block (8-B window). -- SCTLBA - Function 2 I/O space used in Native Mode for the Secondary Controller's Control Block (4-B window). -- LBAR - Function 2 I/O space for the SFF-8038i mode of operation (aka Bus Master IDE) (16-B window). * Device 3, Function 3: -- KTIBA - Function 3 Keyboard and Text IO Block (8-B window). -- KTMBA - Function 3 Keyboard and Text Memory Block (8-B window). The rules for the above programmable ranges are: 1. ALL of these ranges MUST be unique and NON-OVERLAPPING. Note: It is the BIOS or system designers responsibility to limit memory population so that adequate PCI, PCI Express, High BIOS, PCI Express Memory Mapped space, and APIC memory space can be allocated. 2. In the case of overlapping ranges with memory, the memory decode is given priority. 3. There are NO Hardware Interlocks to prevent problems in the case of overlapping ranges. 4. Accesses to overlapped ranges may produce indeterminate results. 5. The only peer-to-peer cycles allowed below the top of memory (register TOLUD) are DMI to PCI Express VGA range writes. Note that peer to peer cycles to the integrated graphics VGA range are not supported. Figure 2 represents system memory address map in a simplified form. 44 Datasheet System Address Map Figure 2. System Address Ranges M a x L im it 6 4 G B P C I M em o ry A d d re s s Range D e v ic e 0 BARS (E P B A R , MCHBAR, P C IE X B A R , D M IB A R ) M a in M e m o ry A d d re s s Range R E M A P B A S E /L IM IT D e v ice 1 (P M B A S E U / P M LIM IT U ) D e v ice 2 (M M A D R , GMADR, G TTM M ADR ) R E M A P L IM IT REM APBASE=TO UUD 4 GB P C I M em o ry A d d re s s Range D e vic e 1 (M B A S E 1 / M L IM IT 1 ) In d e p e n d e n tly P ro g ra m m a b le N o n -O ve rla p p in g W in d o w s D e vic e 3 (M E I_ M M B A R , M E I2 _ M M B A R , K T M B A ) TO LU D M a in M e m o ry A d d re s s Range D e vic e 0 GGC (G ra ph ics S tole n M e m ory ) In d e p e n d e n tly P ro g ra m m a b le N o n -O ve rla p p in g W in d o w s 1 MB Legacy A d d re s s Range 0 NOTE: BARs mapped to the REMAPLIMIT-64 GB space can also be mapped to the TOLUD 4-GB space. (G)MCH variants not supporting 36-bit addressing will require these BARs to be mapped to the TOLUD 4-GB space. 4.1 Legacy Address Range This area is divided into the following address regions: * 0 to 640-kB - MS-DOS* area * 640 to 768-kB - Legacy Video Buffer area * 768 to 896 kB in 16-kB sections (total of eight sections) - Expansion area * 896 to 960 kB in 16-kB sections (total of four sections) - Extended System BIOS area * 960-kB to 1-MB Memory - System BIOS area Datasheet 45 System Address Map Figure 3. DOS Legacy Address Range 1 MB System BIOS (Upper) 64 kB 960 kB Extended System BIOS (Lower) 64 kB (4 x 16 kB) 896 kB 000F_FFFFh 000F_0000h 000E_FFFFh 000E_0000h 000D_FFFFh Expansion Area 128 kB (8 x 16 kB) 000C_0000h 000B_FFFFh 768 kB Legacy Video Area (SMM Memory) 128 kB 000A_0000h 0009_FFFFh 640 kB DOS Area 640 kB 0 46 0000_0000h Datasheet System Address Map 4.1.1 DOS Range (0000_0000h - 0009_FFFFh) The DOS area is 640 kB (0000_0000h to 0009_FFFFh) in size and is always mapped to the main memory controlled by the (G)MCH. 4.1.2 Legacy Video Area (000A_0000h to 000B_FFFFh) The legacy 128-kB VGA memory range, frame buffer, (000A_0000h to 000B_FFFFh) can be mapped to IGD (Device 2), to PCI Express (Device 1), and/or to the DMI. The appropriate mapping depends on which devices are enabled and the programming of the VGA steering bits. Based on the VGA steering bits, priority for VGA mapping is constant. The (G)MCH always decodes internally mapped devices first. Internal to the (G)MCH, decode precedence is always given to IGD. The (G)MCH always positively decodes internally mapped devices, namely the IGD and PCI Express. Subsequent decoding of regions mapped to PCI Express or the DMI depends on the Legacy VGA configuration bits (VGA Enable and MDAP). This region is also the default for SMM space. 4.1.2.1 Compatible SMRAM Address Range (000A_0000h to 000B_FFFFh) When compatible SMM space is enabled, SMM-mode processor accesses to this range are routed to physical system DRAM at 000A 0000h to 000B FFFFh. Non-SMM-mode processor accesses to this range are considered to be to the Video Buffer Area as described above. PCI Express and DMI originated cycles to enabled SMM space are not allowed and are considered to be to the Video Buffer Area if IGD is not enabled as the VGA device. PCI Express and DMI initiated cycles are attempted as Peer cycles, and will master abort on PCI if no external VGA device claims them. 4.1.2.2 Monochrome Adapter (MDA) Range (000B_0000h to 000B_7FFFh) Legacy support requires the ability to have a second graphics controller (monochrome) in the system. Accesses in the standard VGA range are forwarded to IGD, PCI Express, or the DMI (depending on configuration bits). Since the monochrome adapter may be mapped to any one of these devices, the (G)MCH must decode cycles in the MDA range (000B_0000h to 000B_7FFFh) and forward either to IGD, PCI Express, or the DMI. This capability is controlled by a VGA steering bits and the legacy configuration bit (MDAP bit). In addition to the memory range B0000h to B7FFFh, the (G)MCH decodes IO cycles at 3B4h, 3B5h, 3B8h, 3B9h, 3BAh and 3BFh and forwards them to the either IGD, PCI Express, and/or the DMI. 4.1.3 Expansion Area (000C_0000h to 000D_FFFFh) This 128-kB ISA Expansion region (000C_0000h - 000D_FFFFh) is divided into eight 16-kB segments. Each segment can be assigned one of four Read/Write states: readonly, write-only, read/write, or disabled. Typically, these blocks are mapped through (G)MCH and are subtractively decoded to ISA space. Memory that is disabled is not remapped. Non-snooped accesses from PCI Express or DMI to this region are always sent to DRAM. Datasheet 47 System Address Map Table 2. 4.1.4 Expansion Area Memory Segments Memory Segments Attributes Comments 000C_0000h to 000C_3FFFh W/R Add-on BIOS 000C_4000h to 000C_7FFFh W/R Add-on BIOS 000C_8000h to 000C_BFFFh W/R Add-on BIOS 000C_C000h to 000C_FFFFh W/R Add-on BIOS 000D_0000h to 000D_3FFFh W/R Add-on BIOS 000D_4000h to 000D_7FFFh W/R Add-on BIOS 000D_8000h to 000D_BFFFh W/R Add-on BIOS 000D_C000h to 000D_FFFFh W/R Add-on BIOS Extended System BIOS Area (000E_0000h to 000E_FFFFh) This 64-kB area (000E_0000h to 000E_FFFFh) is divided into four, 16-kB segments. Each segment can be assigned independent read and write attributes so it can be mapped either to main DRAM or to DMI. Typically, this area is used for RAM or ROM. Memory segments that are disabled are not remapped elsewhere. Non-snooped accesses from PCI Express or DMI to this region are always sent to DRAM. Table 3. 4.1.5 Extended System BIOS Area Memory Segments Memory Segments Attributes Comments 000E_0000h to 000E_3FFFh W/R BIOS Extension 000E_4000h to 000E_7FFFh W/R BIOS Extension 000E_8000h to 000E_BFFFh W/R BIOS Extension 000E_C000h to 000E_FFFFh W/R BIOS Extension System BIOS Area (000F_0000h to 000F_FFFFh) This area is a single 64-kB segment (000F_0000h - 000F_FFFFh). This segment can be assigned read and write attributes. It is by default (after reset) Read/Write disabled and cycles are forwarded to DMI. By manipulating the Read/Write attributes, the (G)MCH can "shadow" BIOS into the main DRAM. When disabled, this segment is not remapped. Non-snooped accesses from PCI Express or DMI to this region are always sent to DRAM. Table 4. System BIOS Area Memory Segments Memory Segments 000F_0000h to 000F_FFFFh 48 Attributes WE RE Comments BIOS Area Datasheet System Address Map 4.1.6 Programmable Attribute Map (PAM) Memory Area Details The 13 sections from 768 kB to 1 MB comprise what is also known as the PAM Memory Area. The (G)MCH does not handle IWB (Implicit Write-Back) cycles targeting DMI. Since all memory residing on DMI should be set as non-cacheable, there normally will not be IWB cycles targeting DMI. However, DMI becomes the default target for processor and DMI originated accesses to disabled segments of the PAM region. If the MTRRs covering the PAM regions are set to WB or RD it is possible to get IWB cycles targeting DMI. This may occur for DMIoriginated cycles to disabled PAM regions. For example, say that a particular PAM region is set for "Read Disabled" and the MTRR associated with this region is set to WB. A DMI master generates a memory read targeting the PAM region. A snoop is generated on the FSB and the result is an IWB. Since the PAM region is "Read Disabled" the default target for the Memory Read becomes DMI. The IWB associated with this cycle will cause the (G)MCH to hang. 4.2 Main Memory Address Range (1 MB to TOLUD) This address range extends from 1 MB to the top of physical memory that is permitted to be accessible by the (G)MCH (as programmed in the TOLUD register). All accesses to addresses within this range are forwarded by the (G)MCH to the DRAM unless they fall into the optional TSEG, optional ISA Hole, or optional IGD stolen VGA memory. Datasheet 49 System Address Map Figure 4. Main Memory Address Range (0 to 4 GB) 4 GB FFFF_FFFFh F la sh A P IC C onta ins: D e vice 0, 1 , 2 , B A R s & IC H /P C I ranges P C I M e m o ry R a n g e TO LUD In te rn a l G ra p h ic s (o p tio n a l) T S E G (o p tio n a l) M a in M e m o ry 16 M B 15 M B 0100_0000h IS A H o le (o p tio n a l) 00F0_0000h M a in M e m o ry 1 MB 0 4.2.1 0010_0000h D O S C o m p a tib ility M e m o ry 0000_0000h ISA Hole (15 MB to 16 MB) A hole can be created at 15 MB to 16 MB as controlled by the fixed hole enable in Device 0 space. Accesses within this hole are forwarded to the DMI. The range of physical DRAM memory disabled by opening the hole is not remapped to the top of the memory - that physical DRAM space is not accessible. This 15-MB to 16-MB hole is an optionally enabled ISA hole. Video accelerators originally used this hole. It is also used for validation by customer teams for some of their test cards. That is why it is being supported. There is no inherent BIOS request for the 15-MB to 16-MB window. 50 Datasheet System Address Map 4.2.2 Top Segment (TSEG) TSEG is optionally 1 MB, 2 MB, or 8 MB in size. TSEG is below IGD stolen memory, which is at the top of physical memory. System management software may partition this region of memory so it is accessible only by system management software. SMMmode processor accesses to enabled TSEG access the physical DRAM at the same address. Non-processor originated accesses are not allowed to SMM space. PCI Express, DMI, and integrated graphics originated cycles to enabled SMM space are handled as invalid cycle type with reads and writes to location 0 and byte enables turned off for writes. When the extended SMRAM space is enabled, processor accesses to the TSEG range without SMM attribute or without WB attribute are also forwarded to memory as invalid accesses (see Table 6). Non-SMM-mode Write Back cycles that target TSEG space are completed to DRAM for cache coherency. When SMM is enabled the maximum amount of memory available to the system is equal to the amount of physical DRAM minus the value in the TSEG register which is fixed at 1 MB, 2 MB or 8 MB. 4.2.3 Pre-allocated Memory Voids of physical addresses that are not accessible as general system memory and reside within system memory address range (< TOLUD) are created for SMM-mode and legacy VGA graphics compatibility. It is the responsibility of BIOS to properly initialize these regions. Table 5 details the location and attributes of the regions. How to enable and disable these ranges are described in the (G)MCH Control Register Device 0 (GGC). Table 5. Pre-allocated Memory Example for 512-MB DRAM, 64-MB VGA, and 1-MB TSEG Memory Segments 0000_0000h to 1BEF_FFFFh R/W 1BF0_0000h to 1BFF_FFFFh SMM Mode Only Processor Reads 1C00_0000h t 1FFF_FFFFh Datasheet Attributes R/W Comments Available System Memory 447 MB TSEG Address Range & Pre-allocated Memory Pre-allocated Graphics VGA memory 64 MB when IGD is enabled 51 System Address Map 4.3 PCI Memory Address Range (TOLUD to 4 GB) This address range, from the top of physical memory to 4 GB (top of addressable memory space supported by the (G)MCH) is normally mapped to the DMI Interface. Exceptions to this mapping include the BAR memory mapped regions, which include: EPBAR, MCHBAR, and DMIBAR. In the PCI Express port, there are two exceptions to this rule: * Addresses decoded to the PCI Express memory window defined by the MBASE1, MLIMIT1, PMBASE1, and PMLIMIT1 registers are mapped to PCI Express. * Addresses decoded to PCI Express configuration space are mapped based on Bus, Device, and Function number. (PCIEXBAR range). Note: AGP Aperture no longer exists with PCI Express. In an integrated graphics configuration, there are three exceptions to this rule: 1. Addresses decoded to the Graphics Memory Range (GMADR range). 2. Addresses decoded to the Graphics Translation Table range (GTTADR range). 3. Addresses decoded to the Memory Mapped Range of the Integrated Graphics Device (MMADR range). There is a MMADR range for Device 2 Function 0 and a MMADR range for Device 2 Function 1. Both ranges are forwarded to the integrated graphics device. In an Intel Management Engine configuration, there are exceptions to this rule. 1. Addresses decoded to the Intel(R) Management Engine Intel(R) MEI MMIO range (MEI_MMIBAR) 2. Addresses decoded to the Intel Management Engine Intel MEI2 MMIO range (MEI2_MMIBAR) 3. Addresses decoded to the Intel Management Engine IDER MMIO range (PCMDBA, PCTLBA, SCMDBA, SCTLBA, LBAR) 4. Addresses decoded to the Intel Management Engine keyboard and Text MMIO range (KTIBA, KTMBA) The exceptions listed above for integrated graphics and the PCI Express ports MUST NOT overlap with APIC Configuration Space, FSB Interrupt Space and High BIOS Address Range. Note: 52 With the exception of certain BARs, all the above mentioned BARs can be mapped in the TOUUD to 64-GB range in the case of chipset variants supporting 36-bit addressing. See Figure 2 for details. Datasheet System Address Map Figure 5. PCI Memory Address Range 4 GB High BIOS 4 GB minus 2 MB FFFF_FFFFh FFE0_0000h DMI Interface (subtractive decode) FEF0_0000h 4 GB minus 17 MB FSB Interrupts 4 GB minus 18 MB 4 GB minus 19 MB 4 GB minus 20 MB FED0_0000h Local (CPU) APIC FEC8_0000h I/O APIC FEC0_0000h DMI Interface (subtractive decode) PCI Express* Configuration Space E000_0000h 4 GB minus 512 MB Internal Graphics ranges PCI Express Port Optional HSEG FEDA_0000h to FEDB_FFFFh F000_0000h 4 GB minus 256 MB Possible address range FEE0_0000h DMI Interface (subtractive decode) DMI Interface (subtractive decode) TOLUD Datasheet 53 System Address Map 4.3.1 APIC Configuration Space (FEC0_0000h to FECF_FFFFh) This range is reserved for APIC configuration space that includes the default I/O APIC configuration space from FEC0_0000h to FEC7_0FFFh. The default Local (processor) APIC configuration space goes from FEC8_0000h to FECF_FFFFh. Processor accesses to the Local APIC configuration space do not result in external bus activity since the Local APIC configuration space is internal to the processor. However, an MTRR must be programmed to make the Local APIC range uncacheable (UC). The Local APIC base address in each processor should be relocated to the FEC0_0000h (4 GB minus 20 MB) to FECF_FFFFh range so that one MTRR can be programmed to 64 kB for the Local and I/O APICs. The I/O APIC(s) usually reside in the ICH portion of the chip set or as a stand-alone component(s). I/O APIC units are located beginning at the default address FEC0_0000h. The first I/O APIC are located at FEC0_0000h. Each I/O APIC unit is located at FEC0_x000h where x is I/O APIC unit number 0 through F (hex). This address range will normally be mapped to DMI. Note: There is no provision to support an I/O APIC device on PCI Express. 4.3.2 HSEG (FEDA_0000h to FEDB_FFFFh) This optional segment from FEDA_0000h to FEDB_FFFFh provides a remapping window to SMM memory. It is sometimes called the High SMM memory space. SMM-mode processor accesses to the optionally enabled HSEG are remapped to 000A_0000h to 000B_FFFFh. Non-SMM mode processor accesses to enabled HSEG are considered invalid and are terminated immediately on the FSB. The exceptions to this rule are Non-SMM mode Write Back cycles which are remapped to SMM space to maintain cache coherency. PCI Express and DMI originated cycles to enabled SMM space are not allowed. Physical DRAM behind the HSEG transaction address is not remapped and is not accessible. All cache line writes with WB attribute or implicit write backs to the HSEG range are completed to DRAM like an SMM cycle. 4.3.3 FSB Interrupt Memory Space (FEE0_0000 to FEEF_FFFF) The FSB Interrupt space is the address used to deliver interrupts to the FSB. Any device on PCI Express, integrated graphics, or DMI may issue a Memory Write to 0FEEx_xxxxh. The (G)MCH will forward this Memory Write along with the data to the FSB as an Interrupt Message Transaction. The (G)MCH terminates the FSB transaction by providing the response and asserting H_TRDY#. This Memory Write cycle does not go to DRAM. 4.3.4 High BIOS Area The top 2 MB (FFE0_0000h to FFFF_FFFFh) of the PCI Memory Address Range is reserved for system BIOS (High BIOS), extended BIOS for PCI devices, and the A20 alias of the system BIOS. The processor begins execution from the High BIOS after reset. This region is mapped to DMI so that the upper subset of this region aliases to the 16-MB minus 256-kB range. The actual address space required for the BIOS is less than 2 MB, but the minimum processor MTRR range for this region is 2 MB, so a full 2 MB must be considered. 54 Datasheet System Address Map 4.4 Main Memory Address Space (4 GB to TOUUD) Earlier chipsets supported a maximum main memory size of 4-GB total memory. This would result in a hole between TOLUD (Top of Low Usable DRAM) and 4 GB when main memory size approached 4 GB, resulting in a certain amount of physical memory being inaccessible to the system. The new reclaim configuration registers (TOUUD, REMAPBASE, REMAPLIMIT) exist to reclaim lost main memory space. The greater than 32-bit reclaim handling are handled similar to other MCHs. Upstream read and write accesses above 36-bit addressing will be treated as invalid cycles by PCI Express Graphics and DMI. The Top of Memory (TOM) register reflects the total amount of populated physical memory. This is NOT necessarily the highest main memory address (holes may exist in main memory address map due to addresses allocated for memory mapped IO above TOM). TOM is used to allocate the Intel Management Engine stolen memory. The Intel Management Engine stolen size register reflects the total amount of physical memory it has stolen. The Intel Management Engine stolen memory is located at the top of physical memory, and the memory base is calculated by subtracting the amount of memory stolen by the Intel Management Engine from TOM. The Top of Upper Usable DRAM (TOUUD) register reflects the total amount of addressable memory. If reclaim is disabled, TOUUD will reflect TOM minus Intel Management Engine's stolen size. If reclaim is enabled, then it will reflect the reclaim limit. Also, the reclaim base is the same as TOM minus Intel Management Engine stolen memory size to the nearest 64-MB alignment. 4.4.1 Memory Re-Map Background The following examples of Memory Mapped I/O devices are typically located below 4 GB: * High BIOS * H-Seg * T-Seg * Graphics Stolen Memory * XAPIC * Local APIC * FSB Interrupts * Mbase / Mlimit * Memory Mapped I/O space that supports only 32-bit addressing The (G)MCH provides the capability to remap or reclaim the physical memory overlapped by the Memory Mapped I/O logical address space. The (G)MCH re-maps physical memory from the Top of Low Usable DRAM (TOLUD) boundary up to the 4-GB boundary to an equivalent sized logical address range located just below the Intel Management Engine's stolen memory. Datasheet 55 System Address Map 4.4.2 Memory Remapping (or Reclaiming) An incoming address (referred to as a logical address) is checked to see if it falls in the memory re-map window. The bottom of the re-map window is defined by the value in the REMAPBASE register. The top of the re-map window is defined by the value in the REMAPLIMIT register. An address that falls within this window is remapped to the physical memory starting at the address defined by the TOLUD register. The TOLUD register must by 64-MB aligned when remapping is enabled, but can be 1-MB aligned when remapping is disabled. 4.5 PCI Express Configuration Address Space The Device 0 register (PCIEXBAR), defines the base address for the configuration space associated with all devices and functions that are potentially a part of the PCI Express root complex hierarchy. This is a 256-MB block of addresses below top of addressable memory (currently 4 GB) and is aligned to a 256-MB boundary. BIOS must assign this address range in such a way that it will not conflict with any other address ranges. 4.5.1 PCI Express Graphics Attach The (G)MCH can be programmed to direct memory accesses to the PCI Express interface when addresses are within either of two ranges specified via registers in (G)MCH's Device 1 configuration space. * The first range is controlled via the Memory Base Register (MBASE) and Memory Limit Register (MLIMIT) registers. * The second range is controlled via the Prefetchable Memory Base (PMBASE/ PMBASEU) and Prefetchable Memory Limit (PMLIMIT/PMLIMITU) registers. The (G)MCH positively decodes memory accesses to PCI Express memory address space as defined by the following equations: Memory_Base_Address Address Memory_Limit_Address Prefetchable_Memory_Base_Address Address Prefetchable_Memory_Limit_Address It is essential to support a separate Prefetchable range in order to apply USWC attribute (from the processor point of view) to that range. The USWC attribute is used by the processor for write combining. Note that the (G)MCH Device 1 memory range registers described above are used to allocate memory address space for any PCI Express devices sitting on PCI Express that require such a window. The PCICMD1 register can override the routing of memory accesses to PCI Express. In other words, the memory access enable bit must be set in the Device 1 PCICMD1 register to enable the memory base/limit and prefetchable base/limit windows. 4.5.2 Graphics Aperture Unlike AGP, PCI Express has no concept of aperture for PCI Express devices. As a result, there is no need to translate addresses from PCI Express. Therefore, the (G)MCH has no APBASE and APSIZE registers. 56 Datasheet System Address Map 4.6 Graphics Memory Address Ranges The (G)MCH can be programmed to direct memory accesses to IGD when addresses are within any of three ranges specified via registers in (G)MCH's Device 2 configuration space. * The Memory Map Base Register (MMADR) is used to access graphics control registers. * The Graphics Memory Aperture Base Register (GMADR) is used to access graphics memory allocated via the graphics translation table. * The Graphics Translation Table Base Register (GTTADR) is used to access the translation table. Normally these ranges will reside above the Top-of-Main-DRAM and below high BIOS and APIC address ranges. They normally reside above the top of memory (TOLUD) so they do not steal any physical DRAM memory space. GMADR is a Prefetchable range in order to apply USWC attribute (from the processor point of view) to that range. The USWC attribute is used by the processor for write combining. 4.6.1 Graphics Register Ranges The VGA and Extended VGA registers can be accessed via standard VGA I/O locations as well as via memory-mapped locations. In addition, the memory map contains allocation ranges for various functions. The memory space address listed for each register is an offset from the base memory address programmed into the MMADR register (PCI configuration offset 14h). The same memory space can be accessed via dword accesses to I/OBAR. Through the IOBAR, I/O registers MMIO_index and MMIO_data are written. VGA and Extended VGA Control Registers (0000_0000h to 0000_0FFFh): These registers are located in both I/O space and memory space. The VGA and Extended VGA registers contain the following register sets: General Control/Status, Sequencer (SRxx), Graphics Controller (GRxx), Attribute Controller (ARxx), VGA Color Palette, and CRT Controller (CRxx) registers. Instruction, Memory, and Interrupt Control Registers (0000_1000h to 0000_2FFFh): The Instruction and Interrupt Control registers are located in space and contain the types of registers listed in the following sections. 4.6.2 I/O Mapped Access to Device 2 MMIO Space If Device 2 is enabled, and Function 0 within Device 2 is enabled, then IGD registers can be accessed using the IOBAR. MMIO_Index: MMIO_INDEX is a 32-bit register. An I/O write to this port loads the address of the MMIO register that needs to be accessed. I/O Reads returns the current value of this register. MMIO_Data: MMIO_DATA is a 32-bit register. An I/O write to this port is re-directed to the MMIO register pointed to by the MMIO-index register. An I/O read to this port is redirected to the MMIO register pointed to by the MMIO-index register. The memory and I/O maps for the graphics registers are shown in Figure 6, except PCI Configuration registers, which are described in Volume 2 of this document. Datasheet 57 System Address Map Figure 6. Graphics Register Memory and I/O Map Memory Space Map (512 kB allocation) Cursor Registers Display Registers Pixel Pipe Registers TV Out Registers Misc. Multimedia Registers Offset From Base_Reg 0007_FFFFh 0007_0000h 0006_FFFFh 0006_0000h 0005_FFFFh Host Port Registers Note: Some Overlay registers are double-buffered with an additional address range in graphics memory Bit Engine Control Status (RO) 0005_0000h 0004_FFFFh 0004_0000h 0003_FFFFh Overlay Registers 0003_0000h 0002_FFFFh 0001_0000h 0000_FFFFh Reserved 0000_B000h 0000_AFFFh Display Palette Registers 0000_A000h 0000_9FFFh Reserved 0000_7000h 0000_6FFFh Clock Control Registers 0000_6000h 0000_5FFFh Misc I/O Control Registers 0000_5000h 0000_4FFFh Reserved Local Memory Interface Control Registers I/O Space Map (Standard graphics locations) Instruction Control Registers Interrupt Control VGA and Ext. VGA Registers VGA and Ext. VGA Registers 0000_4000h 0000_3FFFh 0000_3000h 0000_2FFFh 0000_1000h 0000_0FFFh 0000_0000h 31 19 MMADR Register (Base Address) 58 Datasheet System Address Map 4.7 System Management Mode (SMM) SMM uses main memory for System Management RAM (SMRAM). The (G)MCH supports: * Compatible SMRAM (C_SMRAM) * High Segment (HSEG)T * Top of Memory Segment (TSEG) SMRAM space provides a memory area that is available for the SMI handlers and code and data storage. This memory resource is normally hidden from the system OS so that the processor has immediate access to this memory space upon entry to SMM. (G)MCH provides three SMRAM options: * Below 1-MB option that supports compatible SMI handlers. * Above 1-MB option that allows new SMI handlers to execute with write-back cacheable SMRAM. * Optional TSEG area of 1 MB, 2 MB, or 8 MB in size. The TSEG area lies below IGD stolen memory. The above 1-MB solutions require changes to compatible SMRAM handlers code to properly execute above 1 MB. Note: DMI and PCI Express masters are not allowed to access the SMM space. 4.7.1 SMM Space Definition SMM space is defined by its addressed SMM space and its DRAM SMM space. The addressed SMM space is defined as the range of bus addresses used by the processor to access SMM space. DRAM SMM space is defined as the range of physical DRAM memory locations containing the SMM code. SMM space can be accessed at one of three transaction address ranges: Compatible, High and TSEG. The Compatible and TSEG SMM space is not remapped and therefore the addressed and DRAM SMM space is the same address range. Since the High SMM space is remapped the addressed and DRAM SMM space are different address ranges. Note that the High DRAM space is the same as the Compatible Transaction Address space. Table 6 describes three unique address ranges: * Compatible Transaction Address (Adr C) * High Transaction Address (Adr H) * TSEG Transaction Address (Adr T) These abbreviations are used later in the table describing SMM Space Transaction Handling. Table 6. Datasheet SMM Space Definition Summary SMM Space Enabled Transaction Address Space DRAM Space (DRAM) Compatible (C) 000A_0000h to 000B_FFFFh 000A_0000h to 000B_FFFFh High (H) FEDA_0000h to FEDB_FFFFh 000A_0000h to 000B_FFFFh TSEG (T) (TOLUD minus STOLEN minus TSEG) to (TOLUD minus STOLEN) (TOLUD minus STOLEN minus TSEG) to (TOLUD minus STOLEN) 59 System Address Map 4.8 SMM Space Restrictions If any of the following conditions are violated, the results of SMM accesses are unpredictable and may cause the system to hang: * The Compatible SMM space must not be set-up as cacheable. * High or TSEG SMM transaction address space must not overlap address space assigned to system DRAM, or to any PCI devices (including DMI, PCI Express, and graphics devices). This is a BIOS responsibility. * Both D_OPEN and D_CLOSE must not be set to 1 at the same time. * When TSEG SMM space is enabled, the TSEG space must not be reported to the OS as available DRAM. This is a BIOS responsibility. * Any address translated through the GMADR must not target DRAM from A_0000F_FFFF. 4.8.1 SMM Space Combinations When High SMM is enabled (G_SMRAME=1 and H_SMRAM_EN=1) the Compatible SMM space is effectively disabled. Processor originated accesses to the Compatible SMM space are forwarded to PCI Express if VGAEN=1 (also depends on MDAP), otherwise they are forwarded to the DMI. PCI Express and DMI originated accesses are never allowed to access SMM space. Table 7. 4.8.2 SMM Space Table Global Enable G_SMRAME High Enable H_SMRAM_EN TSEG Enable TSEG_EN Compatible (C) Range High (H) Range TSEG (T) Range 0 X X Disable Disable Disable 1 0 0 Enable Disable Disable 1 0 1 Enable Disable Enable 1 1 0 Disabled Enable Disable 1 1 1 Disabled Enable Enable SMM Control Combinations The G_SMRAME bit provides a global enable for all SMM memory. The D_OPEN bit allows software to write to the SMM ranges without being in SMM mode. BIOS software can use this bit to initialize SMM code at power up. The D_LCK bit limits the SMM range access to only SMM mode accesses. The D_CLS bit causes SMM data accesses to be forwarded to the DMI or PCI Express. The SMM software can use this bit to write to video memory while running SMM code out of DRAM. 60 Datasheet System Address Map Table 8. 4.8.3 SMM Control Table G_SMRAME D_LCK D_CLS D_OPEN Processor in SMM Mode SMM Code Access SMM Data Access 0 X X X X Disable Disable 1 0 X 0 0 Disable Disable 1 0 0 0 1 Enable Enable 1 0 0 1 X Enable Enable 1 0 1 0 1 Enable Disable 1 0 1 1 X Invalid Invalid 1 1 X X 0 Disable Disable 1 1 0 X 1 Enable Enable 1 1 1 X 1 Enable Disable SMM Space Decode and Transaction Handling Only the processor is allowed to access SMM space. PCI Express and DMI originated transactions are not allowed to SMM space. 4.8.4 Processor WB Transaction to an Enabled SMM Address Space Processor Writeback transactions (REQ[1]# = 0) to enabled SMM address space must be written to the associated SMM DRAM even though D_OPEN=0 and the transaction is not performed in SMM mode. This ensures SMM space cache coherency when cacheable extended SMM space is used. 4.9 Memory Shadowing Any block of memory that can be designated as read-only or write-only can be "shadowed" into (G)MCH DRAM memory. Typically this is done to allow ROM code to execute more rapidly out of main DRAM. ROM is used as read-only during the copy process while DRAM at the same time is designated write-only. After copying, the DRAM is designated read-only so that ROM is shadowed. Processor bus transactions are routed accordingly. 4.10 I/O Address Space The (G)MCH does not support the existence of any other I/O devices beside itself on the processor bus. The (G)MCH generates either DMI or PCI Express bus cycles for all processor I/O accesses that it does not claim. Within the host bridge the (G)MCH contains two internal registers in the processor I/O space, Configuration Address Register (CONFIG_ADDRESS) and the Configuration Data Register (CONFIG_DATA). These locations are used to implement a configuration space access mechanism. The processor allows 64 kB plus 3 B to be addressed within the I/O space. The (G)MCH propagates the processor I/O address without any translation on to the destination bus and therefore provides addressability for 64 kB plus 3 B locations. Note that the upper three locations can be accessed only during I/O address wrap-around when processor Datasheet 61 System Address Map bus H_A#16 address signal is asserted. H_A#16 is asserted on the processor bus whenever an I/O access is made to 4 bytes from address 0000_FFFDh, 0000_FFFEh, or 0000_FFFFh. H_A#16 is also asserted when an I/O access is made to 2 bytes from address 0000_FFFFh. A set of I/O accesses (other than ones used for configuration space access) are consumed by the integrated graphics device if it is enabled. The mechanisms for integrated graphics I/O decode and the associated control is explained later. The I/O accesses (other than ones used for configuration space access) are forwarded normally to the DMI bus unless they fall within the PCI Express I/O address range as defined by the mechanisms explained below. I/O writes are NOT posted. Memory writes to ICH or PCI Express are posted. The PCICMD1 register can disable the routing of I/O cycles to PCI Express. The (G)MCH responds to I/O cycles initiated on PCI Express or DMI with a UR status. Upstream I/O cycles and configuration cycles should never occur. If one does occur, the request will route as a read to memory address 0h so a completion is naturally generated (whether the original request was a read or write). The transaction will complete with a UR completion status. For the processor, I/O reads that lie within 8-byte boundaries but cross 4-byte boundaries are issued from the processor as 1 transaction. The (G)MCH will break this into two separate transactions. This was not done on chipsets prior to the Intel(R) 915 Express Chipset family. I/O writes that lie within 8-byte boundaries but cross 4-byte boundaries are assumed to be split into two transactions by the processor. 4.10.1 PCI Express I/O Address Mapping The (G)MCH can be programmed to direct non-memory (I/O) accesses to the PCI Express bus interface when processor initiated I/O cycle addresses are within the PCI Express I/O address range. This range is controlled via the I/O Base Address (IOBASE) and I/O Limit Address (IOLIMIT) registers in (G)MCH Device 1 configuration space. The (G)MCH positively decodes I/O accesses to PCI Express I/O address space as defined by the following equation: I/O_Base_Address Processor I/O Cycle Address I/O_Limit_Address. The effective size of the range is programmed by the plug-and-play configuration software and it depends on the size of I/O space claimed by the PCI Express device. The (G)MCH also forwards accesses to the legacy VGA I/O ranges according to the settings in the Device 1 configuration registers BCTRL (VGA Enable) and PCICMD1 (IOAE1), unless a second adapter (monochrome) is present on the DMI Interface/PCI. The presence of a second graphics adapter is determined by the MDAP configuration bit. When MDAP is set, the (G)MCH will decode legacy monochrome IO ranges and forward them to the DMI Interface. The IO ranges decoded for the monochrome adapter are 3B4h, 3B5h, 3B8h, 3B9h, 3Bah and 3BFh. Note: 62 The (G)MCH Device 1 I/O address range registers defined above are used for all I/O space allocation for any devices requiring such a window on PCI Express. Datasheet System Address Map 4.11 (G)MCH Decode Rules and Cross-Bridge Address Mapping VGAA = 000A_0000 to 000A_FFFF MDA = 000B_0000 to 000B_7FFF VGAB = 000B_8000 to 000B_FFFF MAINMEM = 0100_0000 to TOLUD 4.11.1 Legacy VGA and I/O Range Decode Rules The legacy 128-kB VGA memory range 000A_0000h to 000B_FFFFh can be mapped to IGD (Device 2), to PCI Express (Device 1), and/or to the DMI depending on the programming of the VGA steering bits. Priority for VGA mapping is constant in that the (G)MCH always decodes internally mapped devices first. Internal to the (G)MCH, decode precedence is always given to IGD. The (G)MCH always positively decodes internally mapped devices, namely the IGD and PCI Express. Subsequent decoding of regions mapped to PCI Express or the DMI depends on the Legacy VGA configurations bits (VGA Enable and MDAP). Datasheet 63 System Address Map 64 Datasheet System Memory Controller 5 System Memory Controller 5.1 Functional Overview The chipset system memory controller supports DDR2 SDRAMs. Dual memory channel organizations are supported: * Dual-channel Interleaved (Single SO-DIMM per channel) * Dual-channel Asymmetric (Single SO-DIMM per channel) Each channel has a 64-bit data interface and the frequencies supported are 533 MHz and 667 MHz. Note: The chipset supports only one SO-DIMM connector per channel. Each channel can have one or two ranks populated. There can be a maximum of four ranks (two double-sided SO-DIMMs) populated. Table 9. System Memory Organization Support for DDR2 DDR2 Tech 5.2 SDRAM Org SO-DIMM size SO-DIMM Org Banks Ranks Page Size (dev/ module) Max Capacity (2 SODIMMs) Freq 256 Mb x8 256 MB 32Mx64 4 1 1K/8K 512 MB 533/667 256 Mb x16 128 MB 16Mx64 4 1 1K/4K 256 MB 533/667 256 Mb x16 256 MB 32Mx64 4 2 1K/4K 512 MB 533/667 512 Mb x8 512 MB 64Mx64 4 1 1K/8K 1 GB 533/667 512 Mb x8 1 GB 128Mx64 4 2 1K/8K 2 GB 533/667 512 Mb x16 256 MB 32Mx64 4 1 1K/8K 512 MB 533/667 512 Mb x16 512 MB 64Mx64 4 2 2K/8K 1 GB 533/667 1 Gb x8 1 GB 128Mx64 8 1 2K/8K 2 GB 533/667 1 Gb x8 2 GB 256Mx64 8 2 1K/8K 4 GB 533/667 Memory Channel Access Modes The system memory controller supports two styles of memory access (dual-channel Interleaved and dual-channel Asymmetric). Rules for populating SO-DIMM slots are included in this chapter. Datasheet 65 System Memory Controller 5.2.1 Dual Channel Interleaved Mode This mode provides maximum performance on real applications. Addresses alternate between the channels after each cache line (64-byte boundary). The channel selection address bit is controlled by DCC[10:9]. If a second request sits behind the first, and that request is to an address on the second channel, that request can be sent before data from the first request has returned. Due to this feature, some progress is made even during page conflict scenarios. If two consecutive cache lines are requested, both may be retrieved simultaneously, since they are guaranteed to be on opposite channels. The drawback of conventional Interleaved mode is that the system designer must populate both channels of memory so that they have equal capacity; however, the technology and device width may vary from one channel to the other. 5.2.1.1 Intel(R) Flex Memory Technology (Dual Channel Interleaved Mode with Unequal Memory Population) The (G)MCH supports interleaved addressing in dual-channel memory configurations even when the two channels have unequal amounts of memory populated. This is called Intel(R) Flex Memory Technology. Intel Flex memory provides higher performance with different sized channel populations than Asymmetric mode (where no interleaving is used) by allowing some interleaving. The memory addresses up to the twice the size of the smaller SO-DIMM are interleaved on a 64-B boundary using address bit 6 (including any XOR-ing already used in interleaved mode). Above this, the rest of the address space is assigned to the remaining memory in the larger channel. Figure 7 shows various configurations of memory populations. Figure 7. Intel(R) Flex Memory Technology Operation NOTES: 1. B: Smaller of the two physical memory amounts: (Accessed in Dual-Channel Interleaved mode) 2. C: Extra memory populated over B: (Accessed in non-interleaved mode) 3. To enable Intel Flex Memory Technology, BIOS should program both channels' DRBs (DRAM Rank Boundaries) to the size of memory in that channel, as if for fully interleaved memory (should not add the top of one channel to the other as in Asymmetric mode). Interleaved mode operation should also be enabled. 4. To disable Intel Flex Memory Technology, BIOS should program as usual for the Asymmetric mode. 66 Datasheet System Memory Controller 5.2.2 Dual Channel Non-Interleaved Mode This mode trades performance for system design flexibility, by allowing unequal amounts of memory to be populated in the two channels. Unlike the previous mode, addresses start in channel A and stay there until the end of the highest rank in channel A, then addresses continue from the bottom of channel B to the top. Real world applications are unlikely to make requests that alternate between addresses that sit on opposite channels with this memory organization, so in most cases, bandwidth is limited. The system designer may populate or not populate any rank on either channel, including either degenerate single channel case. Because channel A is addressed first, when using only one channel, channel A should be the channel used. Figure 8. System Memory Styles Dual Channel Interleaved (Symmetric Population) CL CH1 Dual Channel Non-interleaved (Asymmetric Population) CL Top of Memory CH1 Top of Memory CH0 CH0-top DRB CH0 CH1 CH0 CH1 CH0 0 0 Channel selector controlled by DCC[10:9] 5.3 DRAM Technologies and Organization * All standard 256-Mb, 512-Mb, and 1-Gb technologies and addressing are supported for x16 and x8 devices. For detailed memory organization support, please refer to Table 9. * The (G)MCH supports various page sizes. Page size is individually selected for every rank; 4 k and 8 k for Interleaved and Asymmetric dual-channel modes. * The DRAM sub-system supports only dual channel with 64-bit width per channel. * The number of ranks each channel can have populated is one or two. * Mixed mode, double-sided SO-DIMMs (x8 and x16 on the same SO-DIMM) are not supported. Datasheet 67 System Memory Controller 5.3.1 Rules for Populating SO-DIMM Slots In all modes, the frequency of system memory is the lowest frequency of all SO-DIMMs in the system, as determined through the SPD registers on the SO-DIMMs. The chipset supports only one SO-DIMM connector per channel. * In dual-channel Interleaved mode, both SO-DIMM slots must be populated, and the total amount of memory in each channel must be the same. The device technologies may differ. * In dual-channel Asymmetric mode, the total memory in the two channels need not be equal (one slot could even be unpopulated). When populating only one channel, channel A should be populated. 5.3.2 Pin Connectivity for Dual Channel Modes Table 10. DDR2 Dual Channel Pin Connectivity Dual Channel 5.4 JEDEC Pin Mapping Channel A Channel B CK[1:0] SM_CK[1:0] SM_CK[4:3] CKB[1:0] SM_CK#[1:0] SM_CK#[4:3] CSB[1:0] SM_CS#[1:0] SM_CS#[3:2] CKE[1:0] SM_CKE[1:0] SM_CKE[4:3] ODT[1:0] SM_ODT[1:0] SM_ODT[3:2] BS[2:0] SA_BS[2:0] SB_BS[2:0] MA[14:0] SA_MA[14:0] SB_MA[14:0] RAS# SA_RAS# SB_RAS# CAS# SA_CAS# SB_CAS# WE# SA_WE# SB_WE# DQ[63:0] SA_DQ[63:0] SB_DQ[63:0] DQS[7:0] SA_DQS[7:0] SB_DQS[7:0] DQS[7:0]# SA_DQS#[7:0] SB_DQS#[7:0] DM[7:0] SA_DM[7:0] SB_DM[7:0] DRAM Clock Generation The chipset generates two differential clock pairs for every supported SO-DIMM. There are a total of four clock pairs driven directly by the (G)MCH to two SO-DIMMs. 5.5 DDR2 On Die Termination On die termination (ODT) is a feature that allows a DRAM to turn on/off internal termination resistance for each DQ, DQS/DQS# and DM signal for x8 configurations via the ODT control pin. The ODT improves signal integrity of the memory channel by allowing the DRAM controller to independently turn on/off termination resistance for any or all DRAM devices. 68 Datasheet System Memory Controller The ODT also improves signal integrity of the memory channel by allowing the termination resistance for the DQ, DM, DQS, and DQS# signals to be located inside the DRAM devices themselves instead of on the motherboard. The (G)MCH drives out the required ODT signals, based on memory configuration and which rank is being written to or read from, to the DRAM devices on a targeted SO-DIMM rank to enable or disable their termination resistance. ODT operation follows these general rules: WRITE 1. Chipset: ODT off 2. DRAM: -- If one slot populated but has two ranks, turn on termination in the written rank. -- If one slot/one rank, turn on that rank's termination. READ 1. Chipset: ODT on 2. DRAM: ODT off 5.6 DRAM Power Management 5.6.1 Self Refresh Entry and Exit Operation When entering the Suspend-To-RAM (STR) state, (G)MCH will flush pending cycles and then enter all SDRAM ranks into self refresh. In STR, the CKE signals remain LOW so the SDRAM devices will perform self-refresh. 5.6.2 Dynamic Power Down Operation The chipset implements aggressive CKE control to dynamically put the DRAM devices in a power down state. The (G)MCH controller can be configured to put the devices in active power down (CKE deassertion with open pages) or precharge power down (CKE deassertion with all pages closed). Precharge power down provides greater power savings but has a bigger performance impact, since all pages are needed to be closed before putting the devices in power down mode. If dynamic power down is enabled, all ranks are powered up before doing a refresh cycle and all ranks are powered down at the end of refresh. 5.6.3 DRAM I/O Power Management (G)MCH implements several power-saving features, where different groups of IO buffers are disabled when safe to do so in a dynamic fashion, thereby saving IO power. These features are listed below. * SO-DIMM clock gating disable--The chipset has two clock pairs per SO-DIMM. If only one SO-DIMM is populated, it allows the other two clock pairs to be disabled. * Unused CKE pins can be tri-stated. * Address and control tri-state enable--If CKE for any given rank is deasserted, the CS# to that rank is disabled. If all CKEs are deasserted (such as in S3), all address and control buffers (excluding CKEs) are disabled. Datasheet 69 System Memory Controller * Self refresh master/slave DLL disable--When all the SDRAMs ranks have been put in a self-refresh state, all DLLs are disabled. * Data sense amp disable (self refresh, dynamic)--When all the SDRAM ranks have been put in a self-refresh state, or during normal operation if no memory accesses are pending, the sense amplifiers for all data buffers are turned off. * Output only sense amp disable--Sense amplifiers of all IO buffers that are functionally outputs only (everything except DQ and DQS) are turned off. * RCVEN DLL disable--The (G)MCH has DLLs for timing the RCVEN signal. If only one SO-DIMM is populated, the unused DLLs are turned off. 5.7 System Memory Throttling The chipset has two independent mechanisms, (G)MCH thermal management and DRAM thermal management, that causes system memory bandwidth throttling. For more information on system memory throttling, see Section 11.2. 70 Datasheet PCI Express Based External Graphics 6 PCI Express Based External Graphics See the PCI Express Specification for details on PCI Express. This (G)MCH is part of a PCI Express root complex that connects a host processor/ memory subsystem to a PCI Express hierarchy. The control registers for this functionality are located in Device 1 configuration space and two root complex register blocks (RCRBs). 6.1 PCI Express Architecture Compatibility with the PCI addressing model (a load - store architecture with a flat address space) is maintained to ensure that all existing applications and drivers operate unchanged. The PCI Express configuration uses standard mechanisms as defined in the PCI plug-and-play specification. The initial speed of 2.5-GHz (250 MHz internally) results in 2.5 GB/s direction that provides a 250-MB/s communications channel in each direction (500 MB/s total) and is close to twice the data rate of classic PCI per lane. The PCI Express architecture is specified in layers. The layers include: * Transaction layer * Data Link Layer * Physical layer PCI Express uses packets to communicate information between components. Packets are formed in the transaction and data link layers to carry the information from the transmitting component to the receiving component. As the transmitted packets flow through the other layers, they are extended with additional information necessary to handle packets at those layers. At the receiving side the reverse process occurs and packets get transformed from their physical layer representation to the data link layer representation and finally (for transaction layer packets) to the form that can be processed by the transaction layer of the receiving device. 6.1.1 Transaction Layer The upper layer of the PCI Express architecture, the transaction layer's primary responsibility is the assembly and disassembly of transaction layer Packets (TLPs). TLPs are used to communicate transactions, such as read and write, as well as certain types of events. The transaction layer also manages flow control of TLPs. 6.1.2 Data Link Layer This middle layer in the PCI Express stack serves as an intermediate stage between the transaction layer and the physical layer. Responsibilities include link management, error detection, and error correction. 6.1.3 Physical Layer The physical layer includes all circuitry for interface operation, including driver and input buffers, parallel-to-serial and serial-to-parallel conversion, PLL(s), and impedance matching circuitry. Datasheet 71 PCI Express Based External Graphics 6.2 PCI Express Configuration Mechanism The PCI Express (external graphics) link is mapped through a PCI-to-PCI bridge structure. Figure 9. PCI Express Related Register Structures in (G)MCH GMCH PCI Express Graphics Device PCI Express Link x16 down to x1 PCI-PCI Bridge representing root PCI Express Port (Device 1) PCI Compatible Host Bridge Device (Device 0) RCRB for Egress Port (access to Main Memory) RCRB for DMI (ICH attach) ICH PCI Express extends the configuration space to 4096 bytes per device/function as compared to 256 bytes allowed by PCI Specification. PCI Express configuration space is divided into a PCI-compatible region, which consists of the first 256 bytes of a logical device's configuration space and an extended PCI Express region, which consists of the remaining configuration space. The PCI compatible region can be accessed using either the mechanisms defined in the PCI specification or using the enhanced PCI Express configuration access mechanism described in the PCI Express Enhanced Configuration Mechanism section. The PCI Express host bridge is required to translate the memory-mapped PCI Express configuration space accesses from the host processor to PCI Express configuration cycles. To maintain compatibility with PCI configuration addressing mechanisms, it is recommended that system software access the enhanced configuration space using 32bit operations (32-bit aligned) only. See the PCI Express Specification for details of both the PCI compatible and PCI Express enhanced configuration mechanisms and transaction rules. 72 Datasheet PCI Express Based External Graphics 6.3 Serial Digital Video Output (SDVO) The SDVO description is located here because it is muxed onto the PCI Express x16 port pins. The AC/DC specifications are identical to the PCI Express Graphics interface. SDVO electrical interface is based on the PCI Express interface, though the protocol and timings are completely unique. Whereas PCI Express runs at a fixed frequency, the frequency of the SDVO interface is dependent upon the active display resolution and timing. The port can be dynamically configured in several modes to support display configurations. Essentially, an SDVO port will transmit display data in a high-speed, serial format across differential AC coupled signals. An SDVO port consists of a sideband differential clock pair and a number of differential data pairs. 6.3.1 SDVO Capabilities SDVO ports can support a variety of display types including LVDS, DVI, HDMI, TV-Out, and external CE type devices. The chipset utilizes an external SDVO device to translate from SDVO protocol and timings to the desired display format and timings. The integrated graphics controller can have one or two SDVO ports multiplexed on the x16 PCI Express interface. The SDVO port defines a two-wire, point-to-point communication path between the SDVO device and (G)MCH. The SDVO Control Clock (SDVO_CTRL_CLK) and data (SDVO_CTRL_DATA) provide similar functionality to I2C. However unlike I2C, this interface is intended to be point-to-point (from the (G)MCH to the SDVO device) and will require the SDVO device to act as a switch and direct traffic from the SDVO Control bus to the appropriate receiver. Additionally, the SDVO Control bus is able to run at faster speeds (up to 1 MHz) than a traditional I2C interface would. Figure 10. SDVO Conceptual Block Diagram Monitor Analog RGB TV Clock In Stall Interrupt PCI Express Logic GMCH Datasheet Control Data SDVO Port C Internal Graphics SDVO Port B PCI Express x16 Port Pins Control Clock ClockC RedC GreenC BlueC 3rd Party SDVO External Device(s) Digital Display Device(s) or TV ClockB RedB GreenB BlueB 73 PCI Express Based External Graphics 6.3.2 Concurrent SDVO/PCI Express Operation The (G)MCH supports concurrent operation of the SDVO port with video capture via x1 PCI Express interface. Note that the only type of data supported over the x1 PCI Express link is video capture. SDVO slot reversal is also supported on the GM965/GME965 chipset. The (G)MCH will allow SDVO and x1 PCI Express to operate concurrently on the PCI Express-based Graphics link. The PCI Express lanes comprise a standard PCI Express link and must always originate with lane 0 on the PCI Express connector. The only supported PCI Express width when SDVO is present is x1. This concurrency is supported in reversed and non-reversed configurations. Mirroring / Reversing are always about the axis between lanes 7 and 8. When SDVO is reversed, SDVO Lane 0 corresponds to what would be PCI Express pin/connector lane 15 (mirrored to higher lane numbers). Table 12 shows hardware reset straps used to determine which of the six configurations below is desired. Table 12. Concurrent SDVO / PCI Express* Configuration Strap Controls Configuration Number Description Slot Reversed Strap (CFG9) SDVO Present Strap (SDVO_CTRLDATA) SDVO/PCI Express Concurrent Strap (CFG20) 1 PCI Express*-only not reversed High Low Low 2 PCI Express-only Reversed Low Low Low 3 SDVO-only not reversed High High Low 4 SDVO-only Reversed Low High Low 5 SDVO and PCI Express not reversed High High High 6 SDVO and PCI Express Reversed Low High High NOTE: Details of the implementations corresponding to the configuration number are shown below. 74 Datasheet PCI Express Based External Graphics Figure 11. SDVO/PCI Express Non-Reversed Configurations ( G ) M C H P C Ie L a ne N u m be ring 0 1 3 0 5 0 0 0 0 P C Ie La n e 0 x8 sD V O s D VO La n e 7 PCI Express x16 Connector x 16 P C Ie C ard PCI Express x16 Connector x4 sDVO PCI Express x16 Connector Not Reversed P C Ie V ide o In V id e o O u t sD V O 15 Figure 12. 15 15 15 s D VO La n e 0 15 SDVO/PCI Express* Reversed Configurations (G)MCH PCIe Lane Numbering 15 2 4 6 15 0 15 sDVO Lane 0 15 x4 sDVO sDVO Lane 7 PCI Expres s x16 Connector x8 sDVO PCI Expres s x16 Connector Reversed x16 PCIe Card PCI Expres s x16 Connector sDVO Video Out Video In PCIe 0 6.3.2.1 15 0 0 PCIe Lane 0 0 0 SDVO Signal Mapping Table 13 shows the mapping of SDVO signals to the PCI Express lanes in the various possible configurations as determined by the strapping configuration. Note that slotreversed configurations do not apply to the Integrated graphics-only variants. Datasheet 75 PCI Express Based External Graphics Table 13. Configuration-wise Mapping of SDVO Signals on the PCI Express Interface Configuration-wise Mapping SDVO Only - Normal (3) SDVO Only - Reversed (4) Concurrent SDVO and PCI Express - Normal (5) Concurrent SDVO and PCI Express - Reversed (6) SDVOB_RED# EXP_TXN0 EXP_TXN15 EXP_TXN15 EXP_TXN0 SDVOB_RED EXP_TXP0 EXP_TXP15 EXP_TXP15 EXP_TXP0 SDVOB_GREEN# EXP_TXN1 EXP_TXN14 EXP_TXN14 EXP_TXN1 SDVO Signal SDVOB_GREEN EXP_TXP1 EXP_TXP14 EXP_TXP14 EXP_TXP1 SDVOB_BLUE# EXP_TXN2 EXP_TXN13 EXP_TXN13 EXP_TXN2 SDVOB_BLUE EXP_TXP2 EXP_TXP13 EXP_TXP13 EXP_TXP2 SDVOB_CLKN EXP_TXN3 EXP_TXN12 EXP_TXN12 EXP_TXN3 SDVOB_CLKP EXP_TXP3 EXP_TXP12 EXP_TXP12 EXP_TXP3 SDVOC_RED# EXP_TXN4 EXP_TXN11 EXP_TXN11 EXP_TXN4 SDVOC_RED EXP_TXP4 EXP_TXP11 EXP_TXP11 EXP_TXP4 SDVOC_GREEN# EXP_TXN5 EXP_TXN10 EXP_TXN10 EXP_TXN5 SDVOC_GREEN EXP_TXP5 EXP_TXP10 EXP_TXP10 EXP_TXP5 SDVOC_BLUE# EXP_TXN6 EXP_TXN9 EXP_TXN9 EXP_TXN6 SDVOC_BLUE EXP_TXP6 EXP_TXP9 EXP_TXP9 EXP_TXP6 SDVOC_CLKN EXP_TXN7 EXP_TXN8 EXP_TXN8 EXP_TXN7 SDVOC_CLKP EXP_TXP7 EXP_TXP8 EXP_TXP8 EXP_TXP7 SDVO_TVCLKIN# EXP_RXN0 EXP_RXN15 EXP_RXN15 EXP_RXN0 SDVO_TVCLKIN EXP_RXP0 EXP_RXP15 EXP_RXP15 EXP_RXP0 SDVOB_INT# EXP_RXN1 EXP_RXN14 EXP_RXN14 EXP_RXN1 SDVOB_INT EXP_RXP1 EXP_RXP14 EXP_RXP14 EXP_RXP1 SDVO_FLDSTALL# EXP_RXN2 EXP_RXN13 EXP_RXN13 EXP_RXN2 SDVO_FLDSTALL EXP_RXP2 EXP_RXP13 EXP_RXP13 EXP_RXP2 SDVOC_INT# EXP_RXN5 EXP_RXN10 EXP_RXN10 EXP_RXN5 SDVOC_INT EXP_RXP5 EXP_RXP10 EXP_RXP10 EXP_RXP5 6.4 SDVO Modes The port can be dynamically configured in several modes: * Standard--Baseline SDVO functionality. Supports pixel rates between 25 and 200 MP/s. Utilizes three data pairs to transfer RGB data. * Dual Standard--Utilizes standard data streams across both SDVO B and SDVO C. Both channels can only run in standard mode (three data pairs) and each channel supports pixel rates between 25 and 200 MP/s. There are two types of dual standard modes: 76 Datasheet PCI Express Based External Graphics -- Dual Independent Standard--In Dual Independent Standard mode, each SDVO channel will see a different pixel stream. The data stream across SDVO B will not be the same as the data stream across SDVO C. -- Dual Simultaneous Standard--In Dual Simultaneous Standard mode, both SDVO channels will see the same pixel stream. The data stream across SDVO B is the same as the data stream across SDVO C. The display timings are identical, but the transfer timings may not be; that is, SDVO B Clocks and Data may not be perfectly aligned with SDVO C Clock and Data as seen at the SDVO device(s). Since this utilizes just a single data stream, it utilizes a single pixel pipeline within the (G)MCH. Datasheet 77 PCI Express Based External Graphics 78 Datasheet Integrated Graphics Controller 7 Integrated Graphics Controller The (G)MCH graphics is powered by the Mobile Intel(R) GMA X3100, bringing new levels of richness and realism to DirectX 9 enabled applications. It supports eight programmable Execution cores, enabling greater performance than previous generation chipsets. The Mobile Intel GMA X3100 contain several types of components, which include: the engines, planes, pipes and ports. The Mobile Intel GMA X3100 has a 3D/2D Instruction Processing unit to control the 3D and 2D engines. The Mobile Intel GMA X3100's 3D and 2D engines are fed with data through the memory controller. The outputs of the engines are surfaces sent to memory, which are then retrieved and processed by the Mobile Intel GMA X3100 planes. Figure 13. (G)MCH Graphics Controller Block Diagram Plane A Video Engine Overlay 2D Engine BUFFERS Cursor A VGA 3D Engine Plane B Setup/Transform Rasterizer Texture Engine Pixel Shader Plane C/ Sprite CRT Alpha Blend/ Gamma /Panel Fitter Pipe A M U X Pipe B LVDS TVOUT SDVO B/C Cursor B The Mobile Intel GMA X3100 contains a variety of planes, such as display, overlay, cursor and VGA. A plane consists of a rectangular shaped image that has characteristics such as source, size, position, method, and format. These planes get attached to source surfaces, which are rectangular memory surfaces with a similar set of characteristics. They are also associated with a particular destination pipe. A pipe consists of a set of combined planes and a timing generator. The Mobile Intel GMA X3100 has two independent display pipes, allowing for support of two independent display streams. A port is the destination for the result of the pipe. The entire Mobile Intel GMA X3100 is fed with data from its memory controller. The Mobile Intel GMA X3100 performance is directly related to the amount of bandwidth available. If the engines are not receiving data fast enough from the memory controller (for example, single-channel DDR2 533 MHz), the rest of the Mobile Intel GMA X3100 will also be affected. Datasheet 79 Integrated Graphics Controller 7.1 Graphics Processing 7.1.1 3D Graphics Pipeline * Additional processing capability added to the Geometry stage with a vertex shader, geometry shader, and clipper. * A deep pipelined architecture in which each stage can simultaneously operate on different primitives or on different portions of the same primitive. * Optimized using current and future Intel processor family for advance software based transform and lighting (geometry processing) as defined by Microsoft DirectX API. * Rasterization engine converts vertices to pixels and the texture engine applies textures to pixels. * Rasterization engine takes textured pixels and applies lighting and other environmental affects to produce the final pixel value. * From the rasterization stage the final pixel value is written to the frame buffer in memory so that it can be displayed. 7.1.2 3D Engine Mobile Intel GMA X3100 supports: * 32-bit full precision floating point operations, as against 24-bit in previous chipsets * Up to eight Multiple Render Targets (MRTs), further optimizing performance in execution of instructions. * Acceleration for all Microsoft DirectX 9 and SGI OpenGL 1.5 required features as well as other additional features. Some of the key features supported are: -- The 3D pipeline subsystem performs the 3D rendering acceleration. The main blocks of the pipeline are the Setup Engine, Rasterizer, Texture Pipeline, and Raster Pipeline. A typical programming sequence would be to send instructions to set the state of the pipeline followed by rending instructions containing 3D primitive vertex data. -- The engines' performance is dependent on the memory bandwidth available. Systems that have more bandwidth available will outperform systems with less bandwidth. The engines' performance is also dependent on the core clock frequency. The higher the frequency, the more data is processed. 7.1.2.1 Setup Engine The setup stage of the pipeline takes the input data associated with each vertex of 3D primitive and computes the various parameters required for scan conversion. In formatting this data, the Mobile Intel GMA X3100 maintains sub-pixel accuracy. 7.1.2.1.1 3D Primitives and Data Formats Support The 3D primitives rendered are points, lines, discrete triangles, line strips, triangle strips, triangle fans and polygons. In addition to this, The Mobile Intel GMA X3100 supports the Microsoft DirectX Flexible Vertex Format (FVF), which enables the application to specify a variable length of parameter list obviating the need for sending unused information to the hardware. Strips, Fans and Indexed Vertices, as well as FVF, improve the vertex rate delivered to the setup engine significantly. 80 Datasheet Integrated Graphics Controller 7.1.2.1.2 Pixel Accurate "Fast" Scissoring and Clipping Operation * Supports 2D clipping to the scissor rectangle, avoiding processing pixels that fall outside the rectangle. * Clipping and scissoring in hardware reduce the need for software to clip objects, and thus improve performance. * During the setup stage, clips objects to the scissor window. 7.1.2.1.3 Depth Bias Supports source Depth Biasing in the Setup Engine. Depth Bias value is specified in the vertex command packet on a per primitive basis. The value ranges from -1 to 1. The Depth Bias value is added to the z value of the vertices. By using Depth Bias, it is possible to offset the destination z value (compare value) before comparing with the new z value. 7.1.2.1.4 Backface Culling As part of the setup, the Mobile Intel GMA X3100 discards polygons from further processing, if they are facing away from or towards the user's viewpoint, thus optimizing all further steps. 7.1.2.1.5 Color Shading Modes The Raster engine supports the Flat and Gouraud shading modes. These shading modes are programmed by the appropriate state variables issued through the command stream. Flat shading is performed by smoothly interpolating the vertex intrinsic color components (Red, Green, Blue), Specular Highlights (R,G,B), Fog, and Alpha to the pixel, where each vertex color has the same value. The setup engine substitutes one of the vertex's attribute values for the other two vertices attribute values thereby creating the correct flat shading terms. This condition is set up by the appropriate state variables issued prior to rendering the primitive. Gouraud shading is performed by smoothly interpolating the vertex intrinsic color components (Red, Green, Blue). Specular Highlights (R,G,B), Fog, and Alpha to the pixel, where each vertex color has a different value. 7.1.2.1.6 Occlusion Query Occlusion query is a new addition on the Mobile Intel GMA X3100. It optimizes application performance by minimizing overhead on the depth buffer. It also enables support for new features and effects such as Lens Flare. 7.1.2.2 Rasterizer Working on a per-polygon basis, the rasterizer uses the vertex and edge information is used to identify all pixels affected by features being rendered. 7.1.2.2.1 Pixel Rasterization Rules The Mobile Intel GMA X3100 supports both SGI OpenGL and D3D* pixel rasterization rules to determine whether a pixel is filled by the triangle or line. For both D3D and OpenGL modes, a top-left filling convention for filling geometry will be used. Pixel rasterization rule on rectangle primitive is also supported using the top-left fill convention. Datasheet 81 Integrated Graphics Controller 7.1.2.2.2 Pixel Pipeline The pixel pipeline function combines for each pixel: * Interpolated vertex components from the scan conversion function * Texel values from the texture samplers * Pixel's current values from the color and/or depth buffers This combination is performed via a programmable pixel shader engine, followed by a pipeline for optional pixel operations performed in a specific order. The result of these operations can be written to the color and depth buffers. 7.1.2.3 Texture Engine The Mobile Intel GMA X3100 allows an image, pattern, or video to be placed on the surface of a 3D polygon. The texture processor receives the texture coordinate information from the setup engine and the texture blend information from the rasterizer. The texture processor performs texture color or ChromaKey matching, texture filtering (anisotropic, trilinear and bilinear interpolation), and YUV to RGB conversions. Enhancements to the texture engine include dynamic filtering of up to 16 samples in anistropic filtering, as compared to a maximum of 4 samples in on previous chipsets. 7.1.2.3.1 Perspective Correct Texture Support A textured polygon is generated by mapping a 2D texture pattern onto each pixel of the polygon. A texture map is like wallpaper pasted onto the polygon. Since polygons are rendered in perspective, it is important that texture be mapped in perspective as well. Without perspective correction, texture is distorted when an object recedes into the distance. 7.1.2.3.2 Texture Formats and Storage Supports up to 128 bits of color for textures, including support for textures with floating point components. 7.1.2.3.3 Texture Decompression DirectX supports Texture Compression to reduce the bandwidth required to deliver textures. As the textures' average size gets larger with higher color depth and multiple textures become the norm, it becomes increasingly important to provide a mechanism for compressing textures. Texture decompression formats supported include DXT1, DXT2, DXT3, DXT4, DXT5, FXT1, BC4 and BC5. 7.1.2.3.4 Texture ChromaKey ChromaKey describes a method of removing a specific color or range of colors from a texture map before it is applied to an object. For the nearest texture filter modes, removing a color simply makes those portions of the object transparent (the previous contents of the back buffer show through). For linear texture filtering modes, the texture filter is modified if only the non-nearest neighbor texels match the key (range). 7.1.2.3.5 Texture Map Filtering * Supports many texture mapping modes. Perspective correct mapping is always performed. As the map is fitted across the polygon, the map can be tiled, mirrored in either the U or V directions, or mapped up to the end of the texture and no longer placed on the object (this is known as clamp mode). The way a texture is combined with other object attributes is also definable. 82 Datasheet Integrated Graphics Controller * Supports up to 14 levels of detail (LODs) ranging in size from 8192 X 8192 to 1 x 1 texels. Textures need not be square. Included in the texture processor is a texture cache, which provides efficient MIP mapping. 7.1.2.3.6 Multiple Texture Composition Performs multiple texture composition. This allows the combination of two or more MIP maps to produce a new one with new LODs and texture attributes in a single or iterated pass. Flexible vertex format support allows multitexturing because it makes it possible to pass more than one texture in the vertex structure. 7.1.2.3.7 Cubic Environment Mapping The Mobile Intel GMA X3100 supports cubic reflection mapping over spheres and circles since it is the best choice to provide real-time environment mapping for complex lighting and reflections. * A texture map for each of the six cube faces can be generated by pointing a camera with a 90-degree field-of-view in the appropriate direction. * Per-vertex vectors (normal, reflection or refraction) are interpolated across the polygon and the intersection of these vectors with the cube texture faces is calculated. Texel values are then read from the intersection point on the appropriate face and filtered accordingly. * Supports multiple texture map surfaces arranged into a cubic environment map is supported. * Supports CLAMP and CUBE texture address mode for Cube maps. * Supports new format for Compressed Cube maps that allow each MIP/face to exist in its own compression block. 7.1.2.3.8 Hardware Pixel Shader A pixel shader serves to manipulate a pixel, usually to apply an effect on an image, for example; realism, bump mapping, shadows, and explosion effects. It is a graphics function that calculates effects on a per-pixel basis. 7.1.2.3.9 Color Dithering Color Dithering helps to hide color quantization errors. Color Dithering takes advantage of the human eye's propensity to average the colors in a small area. Input color, alpha, and fog components are converted from 5 or 6-bit component to 8-bit components by dithering. Dithering is performed on blended textured pixels with random lower bits to avoid visible boundaries between the relatively discrete 5/6-bit colors. Dithering is not performed on components containing 8 bits or more. 7.1.2.3.10 Vertex and Per Pixel Fogging Fog is simulated by attenuating the color of an object with the fog color as a function of distance. The higher the density (lower visibility for distant objects). The Mobile Intel GMA X3100 supports both types of fog operations, vertex and per pixel or table fog: * Per-vertex (linear) fogging. The per-vertex method interpolates the fog value at the vertices of a polygon to determine the fog factor at each pixel within the polygon. This method provides realistic fogging as long as the polygons are small. * Per-pixel (non-linear) fogging. the per-vertex technique results in unnatural fogging with large polygons (such as a ground plane depicting an airport runway). Datasheet 83 Integrated Graphics Controller 7.1.2.3.11 Alpha Blending (Frame Buffer) Alpha Blending adds the property of transparency or opacity to an object. Alpha blending combines a source pixel color (RSGSBS) and alpha (AS) component with a destination pixel color (RDGDBD) and alpha (AD) component. For example, this is so that a glass surface on top (source) of a red surface (destination) would allow much of the red base color to show through. Blending allows the source and destination color values to be multiplied by programmable factors and then combined via a programmable blend function. The combined and independent selection of factors and blend functions for color and alpha are supported. 7.1.2.3.12 Color Buffer Formats: 8, 16, 32, 64 or 128 Bits Per Pixel (Destination Alpha) The raster engine will support 8-, 16-, 32-, 64- and 128-bit color buffer formats. The 8bit format is used to support planar YUV420 format, which is used only in Motion Compensation and Arithmetic Stretch format. The bit format of Color and Z is allowed to mix. Supports both double and triple buffering, where one buffer is the primary buffer used for display and one or two are the back buffer(s) used for rendering. The frame buffer contains at least two hardware buffers: the Front Buffer (display buffer) and the Back Buffer (rendering buffer). While the back buffer may actually coincide with (or be part of) the visible display surface, a separate (screen or windowsized) back buffer is used to permit double-buffered drawing. That is, the image being drawn is not visible until the scene is complete and the back buffer made visible (via an instruction) or copied to the front buffer (via a 2D BLT operation). Rendering to one and displaying from the other remove the possibility of image tearing and speeds up the display process over a single buffer. The instruction set of the Mobile Intel GMA X3100 provides a variety of controls for the buffers (e.g., initializing, flip, clear, etc.). 7.1.2.3.13 Depth Buffer The raster engine can read and write from this buffer and use the data in per fragment operations that determine whether resultant color and depth value of the pixel for the fragment are to be updated or not. 7.1.2.3.14 Stencil Buffer The Raster engine provides 8-bit stencil buffer storage in 32- and 64-bit mode and the ability to perform stencil testing. Stencil testing controls 3D drawing on a per pixel basis, conditionally eliminating a pixel on the outcome of a comparison between a stencil reference value and the value in the stencil buffer at the location of the source pixel being processed. They are typically used in multipass algorithms to achieve special effects, such as decals, outlining, shadows and constructive solid geometry rendering. 7.1.2.3.15 Intermediate Z Supports intermediate Z test, which avoids pixel processing on occluded polygons for enhanced 3D graphics performance 7.1.3 2D Engine Contains BLT functionality, and an extensive set of 2D instructions. To take advantage of the 3D drawing engine's functionality, some BLT functions such as Alpha BLTs, arithmetic (bilinear) stretch BLTs, rotations, transposing pixel maps, limited color space conversion, and DIBs make use of the 3D renderer. 84 Datasheet Integrated Graphics Controller 7.1.3.1 Video Graphics Array Registers The 2D registers are a combination of registers for the original Video Graphics Array (VGA) and others that Intel has added to support graphics modes that have color depths, resolutions, and hardware acceleration features that go beyond the original VGA standard. 7.1.3.2 Logical 128-Bit Fixed BLT and 256 Fill Engine Use of this BLT engine accelerates the Graphical User Interface (GUI) of Microsoft Windows operating systems. The 128-bit, Mobile Intel GMA X3100 BLT Engine provides hardware acceleration of block transfers of pixel data for many common Windows operations. The term BLT refers to a block transfer of pixel data between memory locations. The BLT engine can be used for the following: * Move rectangular blocks of data between memory locations * Data alignment * Perform logical operations (raster ops) The rectangular block of data does not change as it is transferred between memory locations. The allowable memory transfers are between: cacheable system memory and frame buffer memory, frame buffer memory and frame buffer memory, and within system memory. Data to be transferred can consist of regions of memory, patterns, or solid color fills. A pattern will always be 8 x 8 pixels wide and may be 8, 16, or 32 bits per pixel. The Mobile Intel GMA X3100 BLT engine: * Can expand monochrome data into a color depth of 8, 16, or 32 bits. * Supports Opaque and Transparent transfers. -- Opaque transfers move the data specified to the destination. -- Transparent transfers compare destination color to source color and write according to the mode of transparency selected. * Horizontally and vertically aligns data at the destination. If the destination for the BLT overlaps with the source memory location, the Mobile Intel GMA X3100 can specify which area in memory to begin the BLT transfer. Hardware is included for all 256 raster operations (Source, pattern, and destination) defined by Microsoft, including transparent BLT. * Provides instructions to invoke BLT and stretch BLT operations, permitting software to set up instruction buffers and use batch processing. * Can perform hardware clipping during BLTs. 7.1.3.3 HW Rotation The Mobile Intel GMA X3100 has made it possible for the primary display of a Dual Display Clone configuration to be independently rotated at 180 when secondary display is in normal mode (0) or vice versa. This is achieved by hardware accelerated rotation. Datasheet 85 Integrated Graphics Controller 7.1.4 Video Engine 7.1.4.1 Dynamic Video Memory Technology (DVMT 4.0) DVMT is an enhancement of the Unified Memory Architecture (UMA) concept, wherein the optimum amount of memory is allocated for balanced graphics and system performance. DVMT ensures the most efficient use of available memory--regardless of frame buffer or main memory size--for balanced 2D/3D graphics performance and system performance. DVMT dynamically responds to system requirements and applications' demands, by allocating the proper amount of display, texturing and buffer memory after the operating system has booted. For example, a 3D application when launched may require more vertex buffer memory to enhance the complexity of objects or more texture memory to enhance the richness of the 3D environment. The operating system views the Intel Graphics Driver as an application, which uses Direct AGP to request allocation of additional memory for 3D applications, and returns the memory to the operating system when no longer required. 7.1.4.2 Intel(R) Clear Video Technology Intel(R) Clear Video Technology enables new features such as: * MPEG-2 Hardware Acceleration * WMV9 Hardware Acceleration * ProcAmp * Advanced Pixel Adaptive De-interlacing * Sharpness Enhancement * De-Noise Filter * High Quality scaling * Film mode detection and correction * Intel(R) TV Wizard to deliver an outstanding media experience on the Mobile Intel GMA X3100 7.1.4.2.1 MPEG-2 Hardware Acceleration MPEG-2 content format is one of the most prevalent formats for video content. Partitioning the MPEG-2 workload between the integrated graphics device and the CPU allows for reduced workload when performing simultaneous support of up to two streams of video. Figure 14 illustrates the hardware acceleration provided by the Mobile Intel GMA X3100 for the MPEG-2 decode pipeline. 86 Datasheet Integrated Graphics Controller Figure 14. MPEG-2 Decode Stage D ecode V a r ia b le L e n g th D ecode In v e r s e Q u a n tiz a tio n In v e r s e D is c re te C o s in e T ra n s fo rm CPU GM CH 7.1.4.2.2 M o tio n C o m p e n s a tio n WMV9 Hardware Acceleration VC-1 is the name given to the WMV9 standard submitted by Microsoft for SMPTE approval. The SMPTE body expanded the scope of VC-1 to also comprehend interlaced content as well as various different transport streams needed for CE and broadcast use. VC-1 content is a format growing in popularity and will be a key format for future high definition content, as both HD-DVD and Blu-Ray* DVD specifications require VC-1 support. WMV9 is bitstream compatible with VC-1, however it is optimized for progressive content only and thus has different software entry points than standard VC-1. The Mobile Intel GMA X3100 core provides hardware acceleration for the WMV9 stages indicated in Figure 15. Note: The various decode stages of WMV9 are typically referred to by letter. The Mobile Intel GMA X3100 core provides hardware acceleration for the WMV9b stage of the decode pipeline, specifically, this accelerates the motion compensation and inloop deblocking stages for progressive content. Datasheet 87 Integrated Graphics Controller Figure 15. WMV9 Decode Stage D ecode V a r ia b le L e n g th D ecode In v e r s e Q u a n tiz a tio n In v e r s e T ra n s fo rm M o tio n C o m p e n s a tio n CPU In -L o o p D e b lo c k in g G M CH 7.1.4.2.3 ProcAmp ProcAmp is the short name for "Processing Amplifier". It is an amplifier to adjust video visual attributes, such as brightness, contrast, hue and saturation. These adjustments are typically controlled by users through the video player application. However when using Microsoft's DXVA driver interface, the ProcAmp calls to the Mobile Intel GMA X3100 core are utilized to perform image enhancements on a frame by frame basis. 7.1.4.2.4 Advanced Pixel Adaptive De-interlacing Interlaced data that originates from a video camera creates two fields that are temporally offset by 1/60 of a second. These fields have alternating lines of data and thus must be adapted for use on progressive PC displays. There are several basic schemes to deinterlace the video stream: line replication, vertical filtering, field merging and vertical temporal filtering. All of these create varying degrees of visual artifacts. The Mobile Intel GMA X3100 core brings with it enhanced hardware integration allowing de-interlacing of video content for a high quality experience with interlaced formats. It also reduces static and motion artifacts with an edge adaptive spatial, temporal filter and motion detector. A pixel adaptive de-interlacing algorithm provides enhanced picture clarity for interlaced content. Hardware acceleration off loads post-processing from CPU to chipset to reduce CPU utilization, further improving performance. 88 Datasheet Integrated Graphics Controller 7.1.4.2.5 Film Mode Detection and Correction A special case of deinterlacing deals with pulled down content. For example, when broadcasting a typical movie over NTSC TV, 3:2 pull down converts 24 progressive frames/sec into 60 interlaced fields/sec. Playing back such an encoded stream using typical deinterlacing methods misses an opportunity to achieve significantly enhanced visual quality. By detecting the repetitive 3:2 cadence, Intel Clear Video Technology can recreate the original progressive frames by working with the original progressive content and artifacts are minimized. Making use of Intel Clear Video Technology's Film Mode Cadence Detection and Correction features is fully transparent to video playback software. Playback software need only request the highest level of deinterlacing be utilized. Intel Clear Video Technology will automatically apply the necessary algorithms for perfect deinterlacing if a recognized cadence is observed. Otherwise, the highest level of deinterlacing supported is utilized. 7.1.4.2.6 Sharpness Enhancement Intel's sharpness enhancement filters reduce the appearance of artifacts by identifying and operating on the edges within an image. By applying noise reduction algorithms specifically on shape edges and improving contrast ratios in these specific regions, Intel Clear Video Technology helps mitigate artifacts that typically accompany high-scale ratios. 7.1.4.2.7 De-noise Filter When working with analog video streams, capturing, converting, and duplicating the content will inject analog noise into the stream; thus degrading the overall video quality. Digital video streams can also exhibit similar artifacts as a result of their original capture or their subsequent compression. Noise artifacts are most noticeable in regions of the image that contain large areas of solid colors. Traditional de-noise algorithms often suppress fine detail within an image by mistaking the detail for noise. However, Intel Clear Video Technology leverages its motion detection algorithms to dramatically reduce the appearance of randomized noise in video streams while accurately preserving fine detail. By realizing that noise artifacts are nondeterministic in their motion, Intel's de-noise filters are able to differentiate between noise and valid video data. 7.1.4.2.8 High Quality Scaling Intel Clear Video Technology's high quality scaling utilizes advanced filtering techniques allowing video to be up-scaled or down-scaled to fit any playback window. This includes non-square scaling. In addition to the obvious benefits of traditional video playback, this also allows for the accurate and efficient mixing of differently sized video streams. The Mobile Intel GMA X3100 core utilizes a 4x4 (polyphase) filter, a 4x4 (bicubic) filter, as well as a 2x2 (bilinear) filter. This allows for playback applications to strike a balance between video quality and performance overhead in specific scenarios. 7.1.4.2.9 Intel(R) TV Wizard Intel TV Wizard is a new, independent GUI application that is packaged with the Intel Graphics driver. Currently PC to TV interaction needs adjustments to get a good quality picture on TV. The application is used by end-users to configure their TV display outputs in a pre-defined sequence. Datasheet 89 Integrated Graphics Controller 7.1.4.3 Sub-Picture Support Sub-picture is used for subtitles for movie captions and menus used to provide some visual operation environments. The Mobile Intel GMA X3100: * Supports sub-picture by mixing the two video streams via alpha blending. Unlike color keying, alpha blending provides a softer effect and each pixel that is displayed is a composite between the two video stream pixels. * Utilizes multiple methods when dealing with sub-pictures. * Enables the Mobile Intel GMA X3100 to work with all sub-picture formats. 90 Datasheet Graphics Display Interfaces 8 Graphics Display Interfaces The graphics display converts a set of source images or surfaces, combines them and sends them out at the proper timing to an output interface connected to a display device. The data can be converted from one format to another, stretched or shrunk, and color corrected or gamma converted. Figure 16. Mobile Intel Gx965 Express Chipset Display Block Diagram Plane A Overlay CRT Cursor A Pipe A LVDS VGA Alpha Blend/ Gamma/ Panel Fitter MUX TVOUT Plane B Plane C/ Sprite Pipe B SDVO B/C Cursor B 8.1 Display Overview Integrated graphics display on the (G)MCH can be broken down into three components: * Display Planes * Display Pipes * Display Ports 8.2 Display Planes The (G)MCH contains a variety of planes, such as Plane A and Plane B, Cursor, Overlay, and Sprite. A plane consists of a rectangular-shaped image that has characteristics such as source, size, position, method, and format. These planes attach to source surfaces, which are rectangular areas in memory with a similar set of characteristics. They are also associated with a particular destination pipe. Datasheet 91 Graphics Display Interfaces 8.2.1 DDC (Display Data Channel) DDC is a standard defined by VESA. DDC allows communication between the host system and display. Both configuration and control information can be exchanged allowing Plug and Play systems to be realized. Support for DDC 1 and 2 is implemented. The chipset uses the CRT_DDC_CLK and CRT_DDC_DATA signals to communicate with the analog monitor. 8.2.1.1 Source/Destination Color Keying/ChromaKeying Overlay source/destination ChromaKeying enables blending of the overlay with the underlying graphics background. Destination color keying/ChromaKeying can be used to handle occluded portions of the overlay window on a pixel by pixel basis that is actually an underlay. Destination ChromaKeying would only be used for YUV pass through to TV. Destination color keying supports a specific color as well as alpha blending. 8.2.1.2 Gamma Correction To compensate for overlay color intensity loss due to the non-linear response between display devices, the overlay engine supports independent gamma correction. This allows the overlay data to be converted to linear data or corrected for the display device when not blending. 8.3 Display Pipes The display consists of two pipes: * Display Pipe A * Display Pipe B A pipe consists of a set of combined planes and a timing generator. The timing generators provide the basic timing information for each of the display pipes. The (G)MCH has two independent display pipes, allowing for support of two independent display streams. A port is the destination for the result of the pipe. The Mobile Intel Gx965 Chipset has flexibility to support all display types from both display pipes with enhanced 3 x 3 panel fitter. It also enables support for 7 x 5 scaling for external TV monitors with over-scan control for HDTV displays. 8.3.1 Clock Generator Units (DPLL) The clock generator units provide a stable frequency for driving display devices. It operates by converting an input reference frequency into an output frequency. The timing generators take their input from internal DPLL devices that are programmable to generate pixel clocks in the range of 25-350 MHz. Accuracy for VESA timing modes is required to be within 0.5%. The DPLL can take a reference frequency from the external reference input (DPLL_REF_CLK / DPLL_REF_CLK#, DPLL_REF_SSCLK / DPLL_REF_SSCLK#), or the TV clock input (TVCLKIN). 8.4 Display Ports Display Ports is the destination for the display pipe. These are the places where the data finally appears to devices outside the graphics device. The (G)MCH has one dedicated: 92 Datasheet Graphics Display Interfaces * Analog Display Port CRT * LVDS Display Port * Analog TV Out * SDVO (B&C) Table 14. Display Port Characteristics (Analog) Interface Protocol S I G N A L S HSYNC Yes Enable/ Polarity Encoded during blanking codes VSYNC Yes Enable/ Polarity Encoded during blanking codes BLANK No No Encoded Encoded STALL No No Yes Yes Field No No No No Display_Enable No Yes Encoded Encoded Image Aspect Ratio Programmable and typically 1.33:1 or 1.78:1 Pixel Aspect Ratio Square Square Voltage RGB 0.7V p-p 1.2 VDC 300 mV p-p Clock Max Rate 8.4.1 RGB DAC Port C (Digital) SDVO 1.0 Port B (Digital) SDVO 1.0 LVDS NA 300 Mpixel Scalable 1.x V 7x Differential (dual channel) 3.5x Differential (Single channel) 224 MPixel (dual channel) 112 Mpixel (single channel) Format Analog RGB Multiple 18 bpp or 24 bpp Type 1 (single channel only) Control Bus DDC1 Optional DDC External Device No No Connector VGA/DVI-I 200 Mpixel RGB 8:8:8 YUV 4:4:4 GMBUS TMDS/LVDS Transmitter /TV Encoder DVI/CVBS/S-Video/Component/ SCART Analog Display Port CRT The analog display port provides an RGB signal output along with a HSYNC and VSYNC signal. There is an associated DDC signal pair that is implemented using GPIO pins dedicated to the analog port. The intended target device is for a CRT-based monitor with a VGA connector. Display devices such as LCD panels with analog inputs may work satisfactory but no functionality has been added to the signals to enhance that capability. Datasheet 93 Graphics Display Interfaces Table 15. Analog Port Characteristics Signal RGB HSYNC VSYNC DDC 8.4.1.1 Port Characteristic Support Voltage Range 0.7 V p-p only Monitor Sense Analog Compare Analog Copy Protection No Sync on Green No Voltage 2.5 V Enable/Disable Port control Polarity adjust VGA or port control Composite Sync Support No Special Flat Panel Sync No Stereo Sync No Voltage Externally buffered to 5 V Control Through GPIO interface Integrated RAMDAC The display function contains a RAM-based Digital-to-Analog Converter (RAMDAC) that transforms the digital data from the graphics and video subsystems to analog data for the CRT monitor. Three 8-bit DACs provide the R, G, and B signals to the monitor. 8.4.1.2 Sync Signals HSYNC and VSYNC signals are digital and conform to TTL signal levels at the connector. Since these levels cannot be generated internally, external level shifting buffers are required. These signals can be polarity adjusted and individually disabled in one of the two possible states. The sync signals should power up disabled in the high state. No composite sync or special flat panel sync support is included. 8.4.2 LVDS Display Port The display pipe selected by the LVDS display port is programmed with the panel timing parameters that are determined by installed panel specifications or read from an onboard EDID ROM. The programmed timing values are then locked into the registers to prevent unwanted corruption of the values. From that point, the display modes are changed by selecting a different source size for that pipe, programming the VGA registers, or selecting a source size and enabling the VGA. The timing signals will remain stable and active through mode changes. These mode changes include VGA to VGA, VGA to HiRes, HiRes to VGA, and HiRes to HiRes. The transmitter can operate in a variety of modes and supports several data formats. The display stream from the display pipe is sent to the LVDS transmitter port at the dot clock frequency, which is determined by the panel timing requirements. Functionality includes: * LVDS output runs at a fixed multiple of the dot clock frequency, which is determined by the mode of operation; single or dual channel. The serializer supports 6-bit or 8-bit color and single or dual channel operating modes. -- A single channel, depending on configuration and mode, can take 18 bits of RGB pixel data plus 3 bits of timing control (HSYNC/VSYNC/DE) and output 94 Datasheet Graphics Display Interfaces them on three differential data pair outputs; or 24 bits of RGB plus 3 bits of timing control output on four differential data pair outputs. -- A dual channel interface converts 36 or 48 bits of color information plus the 3 bits of timing control, and outputs it on six or eight sets of differential data outputs, respectively. * Used in conjunction with the pipe functions of panel scaling and 6- to 8-bit dither. * Used in conjunction with the panel power sequencing and additional associated functions. Note: When enabled, the LVDS constant current drivers consume significant power. Individual pairs or sets of pairs can be selected to be powered down when not being used. When disabled, individual or sets of pairs will enter a low power state. When the port is disabled all pairs enter a low power mode. The panel power sequencing can be set to override the selected power state of the drivers during power sequencing. 8.4.2.1 LVDS Interface Signals There are two LVDS transmitter channels (channel A and channel B) in the LVDS interface. Channel A and Channel B consist of 4-data pairs and a clock pair each. The phase locked transmit clock is transmitted in parallel with the data being sent out over the data pairs and over the LVDS clock pair. Each channel supports transmit clock frequency ranges from 25 MHz to 112 MHz, which provides a throughput of up to 784 Mbps on each data output and up to 112 MP/s on the input. When using both channels, they each operate at the same frequency, each carrying a portion of the data. The maximum pixel rate is increased to 224 MP/s but may be limited to less than that due to restrictions elsewhere in the circuit. The LVDS Port enable bit enables or disables the entire LVDS interface. When the port is disabled, it is in a low power state. Once the port is enabled, individual driver pairs are disabled based on the operating mode. Disabled drivers can be powered down for reduced power consumption or optionally fixed to forced 0's output. 8.4.2.2 LVDS Data Pairs and Clock Pairs The LVDS data and clock pairs are identical buffers and differ only in the use defined for that pair. The LVDS data pair is used to transfer pixel data as well as the LCD timing control signals. The pixel bus data to serial data mapping options are specified elsewhere. A single or dual clock pair is used to transfer clocking information to the LVDS receiver. A serial pattern of 1100011 represents one cycle of the clock. Figure 17 shows a pair of LVDS signals and swing voltage. Figure 17. LVDS Signals and Swing Voltage 1's and 0's are represented by the differential voltage between the pair of signals. Datasheet 95 Graphics Display Interfaces Figure 18. LVDS Clock and Data Relationship 8.4.2.3 LVDS Pair States The LVDS pairs can be put into one of five states: * Powered down tri-state. When in powered down state, the circuit tri-states on both the output pins for the entire channel. * Powered down 0 V. When in powered down state, the circuit enters a low power state and drives out 0 V. * Common mode. The common mode tri-state is both pins of the pair set to the common mode voltage. * Send zeros. When in the send zeros state, the circuit is powered up but sends only zero for the pixel color data, regardless of what the actual data is with the clock lines and timing signals sending the normal clock and timing data. * Active state. When in the active state several data formats are supported. 8.4.2.4 Single Channel versus Dual Channel Mode In the single channel mode, only Channel A is used. In the dual channel mode, both Channel A and Channel B pins are used concurrently to drive one LVDS display. In single channel mode, Channel A is capable of supporting 24-bpp display panels of Type 1 only (compatible with VESA LVDS color mapping). In dual channel mode, Channel A and B are capable of supporting 24-bpp panels of Type 1. Dual channel mode uses twice the number of LVDS pairs and transfers the pixel data at twice the rate of the single channel. In general, one channel is used for even pixels and the other for odd pixel data. The first pixel of the line is determined by the display enable going active and that pixel is sent out Channel A. All horizontal timings for active, sync, and blank are limited to be on two pixel boundaries in the two channel modes. 8.4.2.5 LVDS Channel Skew When in dual channel mode, the two channels must meet the panel requirements with respect to the inter channel skew. 8.4.2.6 LVDS PLL The Display PLL is used to synthesize the clocks that control transmission of the data across the LVDS interface. The three operations that are controlled are the pixel rate, the load rate, and the IO shift rate. These are synchronized to each other and have specific ratios based on single channel or dual channel mode. If the pixel clock is 96 Datasheet Graphics Display Interfaces considered the 1x rate, a 7x or 3.5x speeds the IO_shift clock needed for the high speed serial outputs setting the data rate of the transmitters. The load clock will have either a 1x or 0.5x ratio to the pixel clock. 8.4.2.7 Panel Power Sequencing In order to meet the panel power timing specification requirements two signals, LFP_VDD_EN and LFP_BKLT_EN, are provided to control the timing sequencing function of the panel and the backlight power supplies. A defined power sequence is recommended when enabling or disabling the panel. The set of timing parameters can vary from panel to panel vendor, provided that they stay within a predefined range of values. The panel VDD power, the backlight on/off state and the LVDS clock and data lines are all managed by an internal power sequencer. A requested power-up sequence is only allowed to begin after the power cycle delay time requirement T4 is met. Figure 19. Panel Power Sequencing T4 T1+T2 TX T5 T3 T4 Panel On Panel VDD Enable Panel BackLight Enable Off Clock/Data Lines Off Valid Power On Sequence from off state and Power Off Sequence after full On Datasheet 97 Graphics Display Interfaces Table 16. Panel Power Sequencing Timing Parameters Panel Power Sequence Timing Parameters Spec Name From To Min Max Name Units Vdd On 0.1 Vdd 0.9 Vdd 0 10 T1 ms LVDS Active Vdd Stable On LVDS Active 0 50 T2 ms Backlight LVDS Active Backlight on 200 T5 ms Backlight State Backlight Off LVDS off X X TX ms LVDS State LVDS Off Start power off 0 50 T3 ms Power cycle Delay Power Off Power On Sequence Start 400 0 T4 ms 8.4.3 SDVO Digital Display Port 8.4.3.1 SDVO The (G)MCH utilizes an external SDVO device to translate from SDVO protocol and timings to the desired display format and timings. SDVO ports can support a variety of display types: * LVDS * DVI * Analog TV-Out * Analog CRT * HDMI * External CE type devices 8.4.3.2 SDVO LVDS The (G)MCH may use the SDVO port to drive an LVDS transmitter. Flat panel is a fixed resolution display. The (G)MCH supports panel fitting in the transmitter, receiver or an external device, but has no native panel fitting capabilities. The (G)MCH will provide unscaled mode where the display is centered on the panel. Scaling in the LVDS transmitter through the SDVO stall input pair is also supported. 8.4.3.3 SDVO DVI DVI, a 3.3-V flat panel interface standard, is a prime candidate for SDVO. The (G)MCH provides unscaled mode where the display is centered on the panel. Monitor Hot Plug functionality is supported for DVI devices. 8.4.3.4 SDVO Analog TV-Out The SDVO port supports both standard and high-definition TV displays in a variety of formats. The SDVO port generates the proper blank and sync timing, but the external encoder is responsible for generation of the proper format signal and output timings. (G)MCH will support NTSC/PAL standard definition formats. The (G)MCH will generate the proper timing for the external encoder. The external encoder is responsible for generation of the proper format signal. 98 Datasheet Graphics Display Interfaces The TV-out interface on (G)MCH is addressable as a master device. This allows an external TV encoder device to drive a pixel clock signal on SDVO_TVCLKIN[+/-] that the (G)MCH uses as a reference frequency. The frequency of this clock is dependent on the output resolution required. 8.4.3.5 SDVO Analog CRT The chipset supports SDVO Analog CRT which has similar characteristics as the Integrated Analog CRT (24 bpp, 225-MHz Pixel clock). 8.4.3.6 SDVO HDMI HDMI is a 3.3-V interface that uses TMDS encoding, and requires an active level shifter to get 3.3-V DC coupling. The (G)MCH supports the mandatory features of HDMI Specification 1.3. When combined with a HDMI-compliant external device and connector, the external HDMI device can support standard, enhanced, or high-definition video, plus multi-channel digital audio on a single cable. The (G)MCH has a high speed interface to a digital display (for example, flat panel or digital TV). 8.4.3.7 External CE Type Devices 8.4.3.7.1 TMDS The (G)MCH is compliant with DVI Specification 1.0. DVI requires an SDVO device. The (G)MCH supports panel fitting in the transmitter, receiver, or an external device. 8.4.3.7.2 Flicker Filter and Overscan Compensation The overscan compensation scaling and the flicker filter is done in the external TV encoder chip. Care must be taken to allow for support of TV sets with high performance de-interlacers and progressive scan displays connected to by way of a non-interlaced signal. Timing is generated with pixel granularity to allow more overscan ratios to be supported. 8.4.3.7.3 Direct YUV from Overlay When source material is in the YUV format and is destined for a device that can take YUV format data in, send the data without converting it to RGB. This avoids the truncation errors associated with multiple color conversion steps. 8.4.3.7.4 Analog Content Protection Analog content protection may be provided through the external encoder. 8.4.3.7.5 Connectors Target TV connector support includes the CVBS, S-Video, Analog Component (YPbPr), and SCART connectors. The external TV encoder will determine the method of support. 8.4.3.7.6 Control Bus The SDVO port defines a two-wire communication path between the SDVO device(s) and (G)MCH. Traffic destined for the PROM or DDC will travel across the Control bus, and will then require the SDVO device to act as a switch and direct traffic from the Control bus to the appropriate receiver. Additionally, the Control bus is able to operate at up to 1 MHz. Datasheet 99 Graphics Display Interfaces 8.5 Multiple Display Configurations (G)MCH can support up to two different images on different display devices because it has several display ports available for its two pipes. Parameters include: * Timings and resolutions for these two images may be different. * The (G)MCH can not operate in parallel with an external PCI Express graphics device. * The (G)MCH can work in conjunction with a PCI graphics adapter. 100 Datasheet Power Management 9 Power Management 9.1 Overview * ACPI 3.0 Support -- Global states: G0, G1, G2, G3 -- System states: S0, S3Cold, S4, S5 -- Processor states: C0, C1, C1E, C2, C2E, C3, C4, C4E, Intel Enhanced Deeper Sleep state -- Integrated Graphics Display Device states: D0, D1, D2, D3 -- Integrated Graphics Display Adapter states: D0, D3 * (G)MCH Interface Power Management State Support -- PCI Express Link states: L0, L0s, L1, L2/ L3 ready, L3 -- DMI states: L0, L0s, L1, L2/ L3 ready, L3 -- System Memory: Power up, Pre-charge Power down, Active Power down, SelfRefresh -- SDVO: D0, D1, D2, D3 * Intel Management Engine Power Management State Support -- Intel Management Engine states: M0, M1, Moff * (G)MCH State Combinations * Additional Power Management Features: -- Front Side Bus Interface --Intel Dynamic Front Side Bus Frequency Switching --H_DPWR# --H_CPUSLP# -- PCI Express Graphics / DMI interfaces --CLKREQ# -- System Memory Interface --Intel RMPM --Disabling Unused System Memory Outputs --Dynamic Power Down of Memory -- Integrated Graphics --Intel DPST 3.0 --Intel S2DDT --Dynamic Display Power Optimization (D2PO) Panel Support --Intel Automatic Display Brightness --Intel Display Refresh Rate Switching Datasheet 101 Power Management 9.2 ACPI 3.0 Support 9.2.1 System States State 9.2.2 Description G0/S0 Full On G1/S1 Not supported G1/S1 Not supported G1/S2 Not supported G1/S3-Cold Suspend to RAM (STR). Context saved to memory (S3-Hot is not supported by Mobile Intel(R) Gx965/PM965 Express Chipset) G1/S4 Suspend to Disk (STD). All power lost (except wakeup on ICH) G2/S5 Soft off. All power lost (except wakeup on ICH). Total reboot G3 Mechanical off. All power (AC and battery) removed from system Processor States State 9.2.3 Description C0 Full On C1/C1E Auto Halt C2/C2E Stop Grant. Clock stopped to processor core C3 Deep Sleep. Clock to processor stopped C4/C4E/Intel(R) Enhanced Deeper Sleep Deeper Sleep. Same as C3 with reduced voltage on the processor Integrated Graphics Display Device States State 9.2.4 Description D0 Display active D1 Low power state, low latency recovery, standby display D2 Suspend display D3 Power off display Integrated Graphics Display Adapter States State 102 Description D0 Full on, display active D3 Display off Datasheet Power Management 9.3 (G)MCH Interface Power Management State Support 9.3.1 PCI Express Link States State 9.3.1.1 Description L0 Full on--Active transfer state L0s First Active Power Management low power state--Low exit latency L1 Lowest Active Power Management--Longer exit latency L2/L3 Ready Lower link state with power applied--Long exit latency L3 Lowest power state (power off)--Longest exit latency Dynamic Power Management on I/O * Active power management support using L0, L0s, and L1 states. * All inputs and outputs disabled in L2/L3 Ready state. 9.3.2 DMI States Same as PCI Express Link states. 9.3.3 System Memory States State 9.3.4 Description Power up CKE asserted. Active mode Pre-charge Power down CKE deasserted (not self-refresh) with all banks closed Active Power down CKE deasserted (not self-refresh) with minimum one bank active Self-Refresh CKE deasserted using device self-refresh SDVO State 9.3.4.1 Description D0 Display Active D1 Low power state, low latency recovery, Standby display D2 Suspend display D3 Power off display Dynamic Power Management on I/O * Disabling of SDVO places all SDVO logic and I/O in minimum power state. Datasheet 103 Power Management 9.4 Intel Management Engine Power Management State Support State 9.5 Description M0 Intel(R) Management Engine--Full On M1 Only Intel Management Engine Clocks/Power Rails are enabled in M1-state Moff Intel Management Engine--Full Off (G)MCH State Combinations (G)MCH supports the state combinations listed in the Table 17 and Table 18. 104 Datasheet Power Management Table 17. Table 18. G, S and C State Combinations Global (G) State Sleep (S) State CPU (C) State Processor State System Clocks G0 S0 C0 Full On On Full On G0 S0 C1/C1E Auto-Halt On Auto Halt G0 S0 C2/C2E Stop Grant On Stop Grant G0 S0 C3 Deep Sleep On Deep Sleep G0 S0 C4/C4E/Intel(R) Enhanced Deeper Sleep state On Deep Sleep with lower processor voltage than C3 G1 S3 power off Off, except RTC Suspend to RAM G1 S4 power off Off, except RTC Suspend to Disk G2 S5 power off Off, except RTC Soft Off G3 NA power off Power Off Hard Off Deeper Sleep Description D, S, and C State Combinations Graphics Adapter (D) State Sleep (S) State CPU (C) State Description D0 S0 C0 Full On, Displaying D0 S0 C1/C1E Auto-Halt, Displaying D0 S0 C2/C2E Stop Grant, Displaying D0 S0 C3 Deep Sleep, Displaying D0 S0 C4/C4E/Intel(R) Enhanced Deeper Sleep state Deeper Sleep, Displaying D3 S0 Any Not Displaying D3 S3 --- D3 S4 --- Not Displaying (G)MCH may power off Not Displaying Suspend to disk 9.6 Additional Power Management Features 9.6.1 Front Side Bus Interface 9.6.1.1 Intel Dynamic Front Side Bus Frequency Switching Intel Dynamic Front Side Bus Frequency Switching is a feature where the processor and chipset work together in order to allow a virtual change in the bus clock frequency, thereby reducing frequency by up to half. Reduced frequency allows the processor core voltage to be lowered, thereby consuming less power while still active.This state is exposed as a processor performance state (P-state) and is also known as super LFM. Datasheet 105 Power Management 9.6.1.2 H_DPWR# H_DPWR# signal disables processor sense amps when no read return data is pending. 9.6.1.3 CPU Sleep (H_CPUSLP#) Signal Definition * The processor's sleep signal (SLP#) reduces power in the processor by gating off unused clocks. This signal can be driven only by the (G)MCH's H_CPUSLP# signal. * The (G)MCH host interface controller will ensure that no transactions are initiated on the FSB without having first met the required timing from the SLP# deassertion to the assertion of BPRI#. * (G)MCH will control H_CPUSLP# and enforce the configured timing rules associated with this. This allows the (G)MCH to enforce the timing of the SLP# deassertion to BPRI# assertion during C3 to C2 or C3 to C0 transitions. 9.6.2 PCI Express Graphics/DMI interfaces 9.6.2.1 CLKREQ# - Mode of Operation The CLKREQ# signal is driven by the (G)MCH to control the PCI Express clock to the external graphics and the DMI clock. When both the DMI and PCI Express links (if supported) are in L1, with CPU in C4, C4E or Intel Enhanced Deeper Sleep state, the (G)MCH deasserts CLKREQ# to the clock chip, allowing it to gate the GCLK differential clock pair to the (G)MCH, in turn disabling the PCI Express and DMI clocks inside the (G)MCH. For the (G)MCH to support CLKREQ# functionality, ASPM must enabled on the platform. 9.6.3 System Memory Interface The main memory is power managed during normal operation and in low power ACPI Cx states. 9.6.3.1 Intel Rapid Memory Power Management (Intel RMPM) This technique is to allow all rows of memory to be self-refreshed, with all on chip DLLs off and all SO-DIMM clocks off as long as possible during C3 and above, to reduce power consumption. This is accomplished by adding a mechanism in the memory controller to allow for self-refresh entry and exit during C3 and above and allow for single-row self refresh exit during C3 and above. Intel Rapid Memory Power Management conditionally places memory into self-refresh based on C state, PCI Express link states, and graphics/display activity. Though the dependencies on this behavior are configurable, the target usage is shown in the table below. 106 Datasheet Power Management Table 19. Targeted Memory State Conditions Mode C0, C1, C2 C3, C4, Intel(R) Enhanced Deeper Sleep 9.6.3.2 Memory State with Integrated Graphics Dynamic memory rank power down based on idle conditions Dynamic memory rank power down based on idle conditions If graphics engine is idle, no display requests, and permitted display configuration, then enter self-refresh. Otherwise use dynamic memory rank power down based on idle conditions Memory State with External Graphics Dynamic memory rank power down based on idle conditions Dynamic memory rank power down based on idle conditions If there are no memory requests, then enter self-refresh. Otherwise use dynamic memory rank power down based on idle conditions S3 Self Refresh Mode Self Refresh Mode S4, S5 Memory power down (contents lost) Memory power down (contents lost) Disabling Unused System Memory Outputs Any System Memory (SM) interface signals that go to a SO-DIMM connector in which they are not connected to any actual memory devices (such as SO-DIMM connector is unpopulated, or is single-sided) are tri-stated. The benefits of disabling unused SM signals are: * Reduce power consumption. * Reduce possible overshoot/undershoot signal quality issues seen by the (G)MCH I/O buffer receivers caused by reflections from potentially un-terminated transmission lines. When a given rank is not populated (as determined by the DRAM Rank Boundary Register values) then the corresponding chip select and SCKE signals will not be driven. SCKE tri-state should be enabled by BIOS where appropriate, since at reset all rows must be assumed to be populated. 9.6.3.3 Dynamic Power Down of Memory Dynamic power-down of memory is employed during normal operation. Based on idle conditions, a given memory rank may be powered down. If the pages for a rank have all been closed at the time of power down, then the device will enter the precharge power-down state. If pages remain open at the time of power-down the devices will enter the active power-down state. 9.6.4 Integrated Graphics 9.6.4.1 Intel Display Power Saving Technology 3.0 When enabled, the Intel DPST feature dynamically reduces the power (up to 25%) of the panel backlight based on the brightness distribution in each video frame being displayed. Datasheet 107 Power Management 9.6.4.2 Intel Smart 2D Display Technology Intel S2DDT reduces memory reads, thereby reducing read data power consumption. Intel S2DDT improves most CPU benchmarks due to reduced CPU to memory read latency. The Intel S2DDT engine periodically compresses the front frame buffer data and stores it in a compressed frame buffer. In the upcoming frames, the display engine reads the compressed lines from the compressed frame buffer instead of reading uncompressed lines from the original frame buffer. Lines that were not compressed or lines that were modified since the last compression are displayed from the uncompressed (original) frame buffer. 9.6.4.3 Dynamic Display Power Optimization* (D2PO) Panel Support DPO* is a liquid crystal drive technology developed by Toshiba Matsushita Display Technology Co., Ltd. (TMD) that reduces the power consumption of the LCD for notebook PCs. Intel's implementation of DPO Panel Support feature employs this LCD technology dynamically to achieve significant power savings while maintaining a high quality visual experience. 9.6.4.4 Intel Automatic Display Brightness The Intel Automatic Display Brightness feature dynamically adjusts the backlight brightness based upon the current ambient light environment. This technique provides both potential power savings and usability benefit by automatically decreasing the backlight in dark environments and increasing the backlight in bright environments. 9.6.4.5 Intel Display Refresh Rate Switching Intel Display Refresh Rate Switching is a method of saving power by automatically switching the LCD refresh rate. This method switches between two display timings stored in either the LCD EDID Detailed Timing Descriptors or in the Video BIOS Table. The refresh rate switching will occur during an AC/DC event or when the system boots or resumes from S3/S4 in either AC or battery mode. 108 Datasheet Absolute Maximum Ratings 10 Absolute Maximum Ratings Table 20 specifies the (G)MCH's absolute maximum and minimum ratings. Within functional operation limits, functionality and long-term reliability can be expected. Caution: At conditions outside functional operation condition limits neither functionality nor longterm reliability can be expected. Caution: Although the (G)MCH contains protective circuitry to resist damage from static electric discharge, precautions should always be taken to avoid high static voltages or electric fields. Table 20. Absolute Maximum Ratings (Sheet 1 of 2) Symbol Parameter Min Max Unit Notes1 Tdie Die temperature under bias 0 105 C 1 Tstorage Storage temperature -55 150 C 2,3 VCC 1.05-V core supply voltage with respect to VSS -0.3 1.155 V VCC_AXG 1.05-V graphics voltage with respect to VSS -0.3 1.375 V VCC_AXD 1.25-V DDR2 IO voltage with respect to VSS -0.3 1.375 V VCC_AXM 1.05 Manageability Engine voltage with respect to VSS -0.3 1.155 V (G)MCH 4 Host Interface VTT (FSB VCCP) 1.05-V AGTL+ buffer DC input voltage with respect to VSS -0.3 1.32 V VCC_AXF 1.25-V DC input voltage for AGTL+ buffer logic with respect to VSS -0.3 1.375 V DDR2 Interface (533 MTs/ /667 MTs) Datasheet VCC_SM 1.8-V DDR2 supply voltage with respect to VSS -0.3 2.1 V VCC_SM_CK 1.8-V DDR2 clock IO voltage with respect to VSS -0.3 2.1 V VCCA_SM 1.25-V DDR2 voltage connects to IO logic and DLLs with respect to VSS -0.3 1.375 V VCCA_SM_CK 1.25-V DDR2 voltage for clock module to avoid noise with respect to VSS. -0.3 1.375 V 109 Absolute Maximum Ratings Table 20. Absolute Maximum Ratings (Sheet 2 of 2) Symbol Parameter Min Max Unit Notes1 DMI /PCI Express Graphics/SDVO Interface VCC_PEG 1.05-V PCI Express supply voltage with respect to VSS -0.3 1.375 V VCC_DMI 1.25-V DMI terminal supply voltage with respect to VSS -0.3 1.375 V VCCR_RX_DMI 1.05-V RX and IO logic voltage for DMI -0.3 1.375 V VCCA_PEG_BG 3.3-V analog band gap voltage with respect to VSSA_PEG_BG -0.3 3.63 V Controller LINK 5 CRT DAC Interface (8 bit DAC) VCCA_CRT_DAC 3.3-V DAC IO supply voltage -0.3 3.63 V VCC_SYNC 3.3-V CRT sync supply voltage -0.3 3.63 V VCCD_QCRT 1.5-V CRT quiet digital voltage -0.3 1.65 V VCCD_CRT 1.5-V CRT level shifter supply -0.3 1.65 V -0.3 3.63 V 1.5-V TV supply -0.3 1.65 V 3.3-V TV analog supply -0.3 3.63 V HV CMOS Interface VCC_HV 3.3-V supply voltage with respect to VSS TV OUT Interface (10 bit DAC) VCCD_TVDAC VCCA_TVA_DAC VCCA_TVB_DAC VCCA_TVC_DAC VCCA_DAC_BG 3.3-V TV DAC band gap voltage -0.3 3.63 V VCCD_QTVDAC 1.5-V quiet supply -0.3 1.65 V VCCD_LVDS 1.8-V LVDS digital power supply -0.3 1.98 V VCC_TX_LVDS 1.8-V LVDS data/clock transmitter supply voltage with respect to VSS -0.3 1.98 V VCCA_LVDS 1.8-V LVDS analog supply voltage with respect to VSS -0.3 1.98 V -0.3 1.375 V LVDS Interface PLL Analog Power Supplies VCCA_HPLL, VCCD_HPLL, VCCA_MPLL, VCCA_PEG_PLL, 1.25-V power supply for various PLL VCCD_PEG_PLL, VCCA_DPLLA, VCCA_DPLLB 110 Datasheet Absolute Maximum Ratings NOTES: 1. Functionality is not guaranteed for parts that exceed Tdie temperature above 105C. Tdie is measured at top center of the package. Full performance may be affected if the on-die thermal sensor is enabled. 2. Possible damage to the (G)MCH may occur if the (G)MCH storage temperature exceeds 150C. Intel does not guarantee functionality for parts that have exceeded temperatures above 150C due to spec violation. 3. Storage temperature is applicable to storage conditions only. In this scenario, the device must not receive a clock, and no pins can be connected to a voltage bias. Storage within these limits will not affect the long-term reliability of the device. This rating applies to the silicon and does not include any tray or packaging. 4. Relevant for Controller Link as well. 5. See VCC_AXD 10.1 Power Characteristics Table 21. Mobile Intel 965 Express Chipset Family Thermal Design Power Numbers SKU TDP Unit Notes W 1 Max Unit Notes 0 105 C 1 -55 150 C 2 Mobile Intel(R) GM965/GME965 Express Chipset (render clock 500 MHz) 13.5 Mobile Intel GM965/GME965 Express Chipset (render clock 400 MHz) 12 Mobile Intel GM965/GME965 Express Chipset (mini-note) 10.5 Mobile Intel GM965/GME965 Express Chipset (sub-note) 9.5 Mobile Intel(R) PM965 Express Chipset 8 Mobile Intel(R) GL960/GLE960 Express Chipset Table 22. Symbol <13.5 Power Characteristics (Sheet 1 of 3) Parameter Tdie Die temperature under bias Tstorage Storage temperature Signal Names Min Typ (G)MCH IVCC 1.05-V core supply current (external GFX) 1310. mA 3, 5 IVCC 1.05-V core supply current (integrated GFX) 1572.62 mA 3, 5 IVCC_AXG 1.05-V graphics core supply current 7700 mA 3, 5 IVCC_AXM 1.05-V Manageability Engine supply current 540 mA Datasheet 111 Absolute Maximum Ratings Table 22. Power Characteristics (Sheet 2 of 3) Symbol Parameter Signal Names Min Typ Max Unit Notes Host Interface IVTT FSB at 533 MHz VTT supply current (1.05 V) 700 mA IVTT FSB at 667 MHz VTT supply current (1.05 V) 770 mA IVTT FSB at 800 MHz VTT supply current (1.05 V) 850 mA 1310 mA DMI /PCI Express Graphics/SDVO Interface IVCC_PEG 1.05-V PCI Express supply voltage with respect to VSS IVCC_DMI 1.25-V DMI termination supply voltage with respect to VSS 100 mA IVCCR_RX_DMI 1.05-V IO logic voltage for DMI 260 mA IVCCA_PEG_BG 3.3-V analog band gap voltage with respect to VSSA_PEG_BG 400 A 3, 4, 8 Controller Link IVCC_AXM 9 CRT DAC Interface (8 bit DAC) IVCCA_CRT_ 3.3-V DAC IO supply voltage 70 mA 3, 8 IVCC_SYNC 3.3-V CRT sync supply voltage 10 mA 3, 8 IVCCD_QCRT 1.5-V CRT quiet digital voltage 0.5 mA IVCCD_CRT 1.5-V CRT digital power supply 60 mA 100 mA 3 60 mA 3, 8 mA 3, 8 5 mA 3 0.5 mA DAC HV CMOS Interface IVCC_HV 3.3-V supply voltage with respect to VSS TV OUT Interface (10 bit DAC) IVCCD_TVDAC 1.5-V TV supply IVCCA_TVA_DAC IVCCA_TVB_DAC IVCCA_TVC_ 40 3.3-V TV analog supply 40 40 DAC IVCCA_DAC_BG 3.3-V TV analog supply IVCCD_QTVDAC 1.5-V quiet supply LVDS Interface IVCCD_LVDS 1.8-V LVDS digital power supply 150 mA IVCC_TX_LVDS 1.8-V LVDS data/clock transmitter supply voltage with respect to VSS 100 mA 112 3 Datasheet Absolute Maximum Ratings Table 22. Symbol IVCCA_LVDS Power Characteristics (Sheet 3 of 3) Parameter Signal Names Min Typ 1.8-V LVDS analog supply voltage with respect to VSS Max Unit Notes 10 mA 3 PLL Analog Power Supplies IVCCA_HPLL Host PLL supply current VCCA_HPLL 50 mA 3 IVCCD_HPLL HPLL supply current for digital interface VCCD_HPLL 250 mA 3 100 mA 3 150 mA 3 90 mA 3 IVCCA_DPLLA IVCCA_DPLLB Display PLLA supply current Display PLLB supply current IVCCA_MPLL Memory PLL supply current IVCCA_PEG_PLL IVCCD_PEG_PLL PEG PLL supply current VCCA_DPLLA VCCA_DPLLB VCCA_MPLL VCCA_PEG_PLL VCCD_PEG_PLL NOTES: 1. This specification is the thermal design power and is the estimated maximum possible expected power generated in a component by a realistic application. It is based on extrapolations in both hardware and software technology over the life of the component. It does not represent the expected power generated by a power virus. Studies by Intel indicate that no application will cause thermally significant power dissipation exceeding this specification, although it is possible to concoct higher power synthetic workloads that write but never read. Under realistic read/write conditions, this higher power workload can only be transient and is accounted in the Icc (maximum) specification. Tdie is measured at the top center of the package. 2. These current levels can happen simultaneously, and can be summed into one supply. 3. Estimate is only for maximum current coming through the chipset's supply balls. 4. Rail includes PLL current. 5. Includes worst-case leakage. 6. Calculated for highest stretch goal frequencies. 7. ICCMAX is determined on a per-interface basis, and all cannot happen simultaneously. 8. ICCMAX number includes maximum current for all signal names listed in the table. 9. See IVCC_AXD. Table 23. Symbol DDR2 (533 MTs/667 MTs) Power Characteristics (Sheet 1 of 2) Parameter Min Type Max Unit IVCCSM DDR2 System Memory Interface (1.8 V, 533 MTs) supply current 1 Channel 1395 2 Channel 2700 IVCCSM DDR2 System Memory Interface (1.8 V, 667 MTs) supply current 1 Channel 1700 2 Channel 3300 IVCCSM_CK DDR2 System Memory Interface Clock supply current 200 mA IVCCA_SM (533MT/s) 1.25-V DDR2 IO logic and DLLs supply current 550 mA 1.25-V DDR2 IO logic and DLLs supply current 735 mA IVCCA_SM_CK 1.25-V DDR2 supply current for clock module. 35 mA ISUS_VCCSM DDR2 System Memory interface (1.8 V) standby supply current 5 mA IVCCA_SM (667MT/s) Datasheet Notes mA mA 1 113 Absolute Maximum Ratings Table 23. DDR2 (533 MTs/667 MTs) Power Characteristics (Sheet 2 of 2) Symbol Parameter Min Type Max Unit ISMVREF DDR2 System Memory Interface Reference Voltage (0.90-V) supply current 20 A ISUS_SMVREF DDR2 System Memory Interface Reference Voltage (0.90-V) standby supply current 10 A ITTRC DDR2 System Memory Interface Resister Compensation Voltage (1.8-V) supply current 30 mA ISUS_TTRC DDR2 System Memory Interface Resister Compensation Voltage (1.8-V) standby supply current 0 mA Max Unit Notes 1 NOTES: 1. Standby in Table 23 refers to system memory in Self Refresh during S3 (STR). Table 24. VCC Auxiliary Rail Power Characteristics Symbol Parameter Min Type Notes IVCC_AXD Supply current for HSIO 515 mA 1,2 IVCC_AXF Supply current FSB IO 495 mA 1 NOTES: 1. Calculated for highest frequency of operation. 2. Relevant for Controller Link as well. 10.2 Thermal Characteristics The (G)MCH is designed for operation at die temperatures between 0C and 105C. The thermal resistance of the package is given in the following table. Table 25. Mobile Intel 965 Express Chipset Family Package Thermal Resistance Parameter Airflow Velocity in Meters/Second 0 m/s (0 LFM) 1 m/s (200 LFM) jt (C/Watt)1 23.5 C/W 18.3 C/W ja (C/Watt)1 0.5 C/W 0.9 C/W NOTES: 1. Estimate. 114 Datasheet Thermal Management 11 Thermal Management System level thermal management requires two solutions: 1. Robust Thermal Solution Design: The system's thermal solution should be capable of dissipating the platform's thermal design power while keeping all components below the relevant Tdie_max under the intended usage conditions. Such conditions include ambient air temperature and available airflow inside the laptop. 2. Thermal Failsafe Protection Assistance: As a backup to the thermal solution, the system design should provide additional thermal protection for the components. The failsafe assistance mechanism reduces the risk of damage by excessive thermal stress in situations where the thermal solution is inadequate or has failed. Details on implementing these solutions are provided in the following sections. 11.1 Internal Thermal Sensors The (G)MCH incorporates two on-die thermal sensors for thermal management. The thermal sensors may be programmed to cause hardware throttling and/or software interrupts. Hardware throttling includes render and main memory programmable throttling thresholds. Sensor trip points may also be programmed to generate interrupts or integrated graphics interrupt. Table 26 shows the internal thermal sensor trip points, which are listed in the order of increasing temperature. Table 26. Trip Points Trip Point Description Aux0, 1, 2, 3 Temperature Trip Points May be set dynamically and provide an interrupt to ACPI (or other software) when crossed in either direction. Do not automatically cause any hardware throttling but may be used by software to trigger interrupts. Should be programmed for software and firmware control via interrupts. Hot Set at the temperature at which the MCH must start throttling. It may enable (G)MCH throttling when the temperature is exceeded. May provide an interrupt to ACPI (or other software) when it is crossed in either direction. Software could optionally set this as an interrupt when the temperature exceeds this level setting. Should be set to throttle (G)MCH to avoid maximum Tj of 110C. Catastrophic Set at the temperature at which the (G)MCH must be shut down immediately without any software support. The catastrophic trip point may be programmed to generate an interrupt, enable throttling, or immediately shut down the system (via Halt, or via THERMTRIP# assertion). Crossing a trip point in either direction may generate several types of interrupts. Each trip point has a register to select what type of interrupt is generated. Crossing a trip point is implemented as edge detection, used to trigger the interrupts. Either edge (i.e., crossing the trip point in either direction) generates the interrupt. Should be set to halt operation to avoid maximum Tj of 130C. NOTE: Contact your Intel representative for recommended Trip Point programming. Thermal sensors are not located in hotspot of (G)MCH. Thermal sensors may be up to 4C lower than maximum Tj of (G)MCH. Trip Points should be set to account for temperature offset between thermal sensors and maximum Tj hotspot and thermal sensor accuracy. Datasheet 115 Thermal Management 11.1.1 Thermal Sensor Accuracy * Thermal sensor accuracy for (G)MCH is 8 C from approximately +80C to Tj-max of 110C. * Temperature reading accuracy from Thermal sensor will degrade further with junction temperatures below +80C. * Temperature readings from thermal sensor may not be available below +40C. * (G)MCH may not operate above Tj-max of +110C. Note: Software may program the Tcat, Thot, and Taux trip points, but these trip points should be selected with consideration for the thermal sensor accuracy and the quality of the platform thermal solution. Overly conservative (unnecessarily low) temperature settings may unnecessarily degrade performance due to frequent throttling, while overly aggressive (dangerously high) temperature settings may fail to protect the part against permanent thermal damage. 11.1.2 Sample Programming Model Intel reference and driver code do not use the thermal sensor interrupts. 11.1.2.1 Setting Trip Point for Hot Temperature and Generating an SERR Interrupt * Program the Thermal Hot Temperature Setting Register (TSTTPA1.HTPS or TSTTPA2.HTPS). * In Thermal Sensor Control Register (TSC1 or TSC2), set the thermal sensor enable bit (TSE), and the hysteresis value (if applicable). * In Thermal Error Command Register (TERRCMD), set the SERR on Hot Thermal Sensor Event (bit 4). * Program the global thermal interrupt enabling registers. 11.1.2.2 Temperature Rising above the Hot Trip Point * The TIS [Hot Thermal Sensor Interrupt Event] is set when SERR interrupt is generated. * Clear this bit of the TIS register to allow subsequent interrupts of this type to get registered. * Clear the global thermal sensor event bit in the Error Status register. * In thermal sensor status register (TSS), the Hot Trip indicator (HTI) bit is set if this condition is still valid by the time the software gets to read the register. 11.1.2.3 Determining the Current Temperature as Indicated by the Thermometer * In the Thermal Sensor Control register (TSC1) set the thermal sensor enable bit (TSE) and the hysteresis value (if applicable). * Read the value in the Thermometer Reading register (TR). Allow enough time for the entire thermometer sequence to complete (less than 1.3 msec = 512 * 256 / 100 MHz for hraw clock of 100 MHz) in 512 clock mode. Reading is not valid unless TSS [Thermometer Output Valid] = 1. 116 Datasheet Thermal Management 11.1.3 Hysteresis Operation * Hysteresis provides a small amount of positive feedback to the thermal sensor circuit to prevent a trip point from flipping back and forth rapidly when the temperature is right at the trip point. * The digital hysteresis offset is programmable to be 0,1, 2...15, which corresponds to an offset in the range of approximately 0 to 7C. 11.2 External Thermal Sensor Interface Customers have the ability to determine the settings for platform throttling via external thermal sensors. These external thermal sensors can be enabled to measure temperature of external components, such as memory. Multiple thermal sensors can also be wired together, which allows thermal sensing from multiple components that are separate; that is, two memory SO-DIMMs. Software can, if necessary, distinguish which SO-DIMM(s) is the source of the over-temp through the serial interface. However, since the SO-DIMM's are located on the same Memory Bus Data lines, any (G)MCH-based Read Throttle applies equally. Note: The use of external sensors that include an internal pull-up resistor on the open-drain thermal trip output is discouraged; however, it may be possible, depending on the size of the pull up and the voltage of the thermal sensor. Figure 20. Platform External Thermal Sensor External Pull-up R is associated with the voltage rail of the MCH Input CPU V R PM_EXT_TS (G)MCH THERM# SO-DIMMs TS TS ICH SMBdata SMBclock Datasheet 117 Thermal Management 11.3 Thermal Throttling Options With the internal and external thermal sensors now enabled, the (G)MCH has two independent mechanisms that cause system memory throttling. * (G)MCH Thermal Management: This is to ensure that the (G)MCH is operating within thermal limits. The mechanism can be initiated by a thermal sensor (internal) trip or by virtual thermal sensor bandwidth measurement exceeding a programmed threshold via a weighted input averaging filter. * DRAM Thermal Management ensures that the DRAM chips are operating within thermal limits. The (G)MCH can control the amount of (G)MCH initiated bandwidth per rank to a programmable limit via a weighted input averaging filter. 11.4 THERMTRIP# Operation Assertion of the (G)MCH's THERMTRIP# (Thermal Trip) indicates that its junction temperature has reached a level beyond which damage may occur. Upon assertion of THERMTRIP#, the (G)MCH will shut off its internal clocks (thus halting program execution) in an attempt to reduce the core junction temperature. Once activated, THERMTRIP# remains latched until RSTIN# is asserted. 118 Datasheet DC Characteristics 12 DC Characteristics See Section 2 for signal type and corresponding buffer description. Table 27. Signal Group Signal Groups (Sheet 1 of 4) Signal Type Signals Notes Host Interface Signal Groups (a) (b) (c) (d) (e) I/O AGTL+ O AGTL+ O LVCMOS I AGTL+ I A I/O A H_ADS#, H_BNR#, H_BREQ#,H_DBSY#, H_DRDY#, H_DINV#[3:0], H_A#[35:3], H_ADSTB#[1:0], H_D#[63:0],H_DSTBP#[3:0], H_DPWR#, H_DSTBN#[3:0], H_HIT#, H_HITM#, H_REQ#[4:0] H_BPRI#, H_CPURST#, H_DEFER#, H_TRDY#, H_RS#[2:0], THERMTRIP# H_CPUSLP H_LOCK# H_AVREF, H_DVREF, H_SWING H_RCOMP, H_SCOMP, H_SCOMP# Serial DVO or PCI-Express Graphics Interface Signal Groups PCI-E GFX Interface: PEG_RX[15:0], PEG_RX#[15:0] (f) I PCI Express* SDVO Interface: SDVO_TVCLKIN#, SDVO_TVCLKIN, SDVO_INT, SDVO_INT#, SDVO_FLD_STALL#, SDVO_FLD_STALL Refer to EDS for SDVO & PCI Express GFX pin mapping PCI-E GFX Interface: PEG_TX[15:0], PEG_TX#[15:0] (g) (h) Datasheet O PCI Express SDVO Interface: SDVOB_RED#, SDVOB_RED, SDVOB_GREEN#, SDVOB_GREEN, SDVOB_BLUE#, SDVOB_BLUE, SDVOB_CLK, SDVOB_CLK#, SDVOC_RED#/SDVOB_ALPHA#, SDVOC_RED/ SDVOB_ALPHA, SDVOC_GREEN#, SDVOC_GREEN, SDVOC_BLUE#, SDVOC_BLUE, SDVOC_CLK, SDVOC_CLK# I PEG_COMPO A PEG_COMPI Refer to EDS for SDVO & PCI Express GFX pin mapping Analog PCI-E GFX/SDVO I/F compensation signals 119 DC Characteristics Table 27. Signal Group Signal Groups (Sheet 2 of 4) Signal Type Signals Notes DDR2 Interface Signal Groups (l) (j) I/O SSTL-1.8 O SSTL-1.8 SA_DQ[63:0], SB_DQ[63:0] SA_DQS[7:0], SB_DQS[7:0], SA_DQS[7:0]#, SB_DQS#[7:0] SA_DM[7:0], SB_DM[7:0], SA_MA[14:0], SB_MA[14:0], SA_BS[2:0], SB_BS[2:0], SA_RAS#, SB_RAS#, SA_CAS#, SB_CAS#, SA_WE#, SB_WE#, SM_ODT[3:0], SM_CKE[3:0], M_CS#[3:0], SM_CK[1:0], SM_CK#[1:0], SM_CK[4:3], SM_CK#[4:3] I SSTL-1.8 (k) I A SA_RCVEN#, SB_RCVEN# SM_VREF LVDS Signal Groups (l) (m) O LVDS I/O Ref I Ref LVDSA_DATA[3:0], LVDSA_DATA#[3:0], LVDSA_CLK, LVDSA_CLK#, LVDSB_DATA[3:0], LVDSB_DATA#[3:0], LVDSB_CLK, LVDSB_CLK# LVDS_IBG LVDS_VBG, LVDS_VREFH, LVDS_VREFL CRT DAC Signal Groups (n) (o) (p) O A O A O HVCMOS CRT_RED, CRT_RED#, CRT_GREEN, CRT_GREEN#, CRT_BLUE, CRT_BLUE# Refer to CRT/ analog VESA spec & EDS CRT_TVO_IREF Current mode reference pin. DC spec. not required CRT_HSYNC, CRT_VSYNC Refer to CRT/ analog VESA spec & EDS TV DAC Signal Groups (q) O A O HVCMOS (ae) 120 TV DAC band gap and channel supply TVA_DAC, TVB_DAC, TVC_DAC, TVA_RTN, TVB_RTN, TVC_RTN TV_DCONSEL[1:0] VCCA_TVA_DAC,VCCA_TVB_DAC, VCCA_TVC_DAC, VCCA_DAC_BG Datasheet DC Characteristics Table 27. Signal Group Signal Groups (Sheet 3 of 4) Signal Type Signals Notes Clocks, Reset, and Miscellaneous Signal Groups (s) (t) (u) (ua) (v) (va) HVCMOS input Low voltage diff. clock input O HVCMOS O A I HVCMOS I/O COD I Diff clock (w) (x) (xa) AGTL+ input/output I HVCMOS I LVCMOS PM_EXT_TS[1:0]#, HCLKP(BCLK0/BCLK), HCLKN(BCLK1/BCLK#), DREF_CLKP, DREF_CLKN, DREF_SSCLKP, DREF_SSCLKN, GCLKP, GCLKN L_VDD_EN, L_BKLT_EN, L_BKLT_CRTL, CLK_REQ#, ICH_SYNC# GFX_VID[3:0], GFX_VR_EN PMSYNC# (PM_BM_BUSY#) CRT_DDC_CLK, CRT_DDC_DATA, L_DDC_CLK, L_DDC_DATA, SDVO_CTRL_CLK, SDVO_CTRL_DATA, L_CRTL_CLK, L_CRTL_DATA DDC and GMBUS support signals DPLL_REF_CLK, DPLL_REF_CLK#, DPLL_REF_SSCLK, DPLL_REF_SSCLK#, HPLL_CLK, HPLL_CLK#, PEG_CLK, PEG_CLK# PLL signals CFG[17:3] RSTIN#, PWROK, CFG[20:18], H_BSEL[2:0] / CFG[2:0], PM_EXT_TS#[1:0, TEST1, TEST2 PM_DPRSTP# I/O Buffer Supply Voltages (y) AGTL+ termination voltage VTT (Vccp) (z) SDVO, DMI, PCI Express GFX voltages VCC3G, VCCA_3GBG (aa) 1.8-V DDR2 supply voltage VCCSM (ab) (G)MCH core VCC (ac) HV supply voltage VCCHV (ad) TV DAC supply voltage VCCD_TVDAC, VCCDQ_TVDAC (ae) TV DAC band gap and channel supply VCCA_TVDACA,VCCA_TVDACB, VCCA_TVDACC (af) CRT DAC supply voltage VCCA_CRTDAC, VCCDQ_CRT, VCCD_CRT, VCC_SYNC (ag) PLL supply voltages VCCA_HPLL, VCCA_MPLL, VCCD_HMPLL VCCA_3GPLL, VCCA_DPLLA, VCCA_DPLLB (ah) 1.8-V LVDS digital supply VCCD_LVDS Datasheet 121 DC Characteristics Table 27. Signal Groups (Sheet 4 of 4) Signal Group Signal Type Signals (ai) 1.8-V LVDS Data/ clock transmitter supply VCCTX_LVDS (aj) 1.8-V LVDS analog supply VCCA_LVDS (ak) 1.25-V power supply for DDR2 DLL, DDR2 IO and FSB IO VCC_AXD and VCC_AXF Notes Controller Link Signals (al) VCC-independent CMOS I/O (al) HVCMOS input CL_PWROK (al) CMOS input CL_RST#, (al) Analog input CL_VREF 12.1 CL_DATA, CL_CLK, General DC Characteristics The I/O buffer supply voltage is measured at the (G)MCH package pins. The tolerances shown in Table 28 are inclusive of all noise from DC up to 20 MHz. Table 28 also indicates which supplies are connected directly to a voltage regulator or to a filtered voltage rail. Voltages connected to a filter should be measured at the input of the filter. If the platform decoupling guidelines cannot be met, tradeoffs between the voltage regulator output DC tolerance and the decoupling performance of the capacitor network are necessary to stay within the voltage tolerances. Table 28. DC Characteristics (Sheet 1 of 6) Signal Group Min Nom Max Unit 1.05-V Host AGTL+ termination voltage 0.9975 1.05 1.1025 V 1.25-V DC input voltage for AGTL+ IO logic 1.1875 1.25 1.3125 V 1.05-V (G)MCH core supply voltage 0.9975 1.05 1.1025 V VCC_AXG 1.05-V graphics voltage 0.9975 1.05 1.1025 V VCC_AXM 1.05-V Intel(R) Management Engine voltage 0.9975 1.05 1.1025 V 1.7 1.8 1.9 V Symbol Parameter Notes I/O Buffer Supply Voltage VTT (y) VCC_AXF VCC VCC_SM 122 (ab) (aa) DDR2 I/O supply voltage 16 Datasheet DC Characteristics Table 28. Symbol DC Characteristics (Sheet 2 of 6) Signal Group Parameter Min Nom Max Unit 1.7 1.8 1.9 V VCC_SM_CK 1.8-V DDR2 clock IO voltage VCCA_SM 1.25-V DDR2 voltage connects to IO logic and DLLs 1.1875 1.25 1.3125 V VCC_AXD 1.25-V DDR2 high speed IO logic voltage and controller link IO 1.1875 1.25 1.3125 V VCCA_SM_CK 1.25-V DDR2 IO logic voltage for SM clocks 1.1875 1.25 1.3125 V 1.05-V PCI Express supply voltage 0.9975 1.05 1.1025 V VCC_DMI 1.25-V TX analog and term voltage for DMI 1.1875 1.25 1.3125 V VCCR_RX_DMI 1.05-V Rx and I/O logic for DMI 0.9975 1.05 1.1025 V VCCA_PEG_BG 3.3-V analog band gap voltage 3.135 3.3 3.465 V HV CMOS supply voltage 3.135 3.3 3.465 V VCC_PEG (z) VCCHV (ac) VCCD_TVDAC (ad) TV DAC supply voltage 1.425 1.5 1.575 V VCCD_QTVDAC (ad) TV DAC quiet supply voltage 1.425 1.5 1.575 V VCCA_TVA_DAC VCCA_TVB_DAC VCCA_TVC_DAC VCCA_DAC_BG (ae) TV DAC analog & band gap supply voltage 3.135 3.3 3.465 V VCCA_CRT_DAC (af) CRT DAC supply voltage 3.135 3.3 3.465 V VCC_SYNC (af) CRT DAC SYNC supply voltage 3.135 3.3 3.465 V VCCD_QCRT 1.5-V CRT quiet digital voltage 1.425 1.5 1.575 VCCD_CRT 1.5-V CRT digital power supply 1.425 1.5 1.575 Notes VCCA_HPLL VCCA_MPLL VCCD_HPLL (ag) Various PLLS analog supply voltages 1.1875 1.25 1.3125 V VCCD_LVDS (ah) Digital LVDS supply voltage 1.7 1.8 1.9 V VCC_TX_LVDS (ai) Data/clock transmitter LVDS supply voltage 1.7 1.8 1.9 V VCCA_PEG_PLL VCCD_PEG_PLL VCCA_DPLLA VCCA_DPLLB Datasheet 123 DC Characteristics Table 28. DC Characteristics (Sheet 3 of 6) Symbol Signal Group Parameter Min Nom Max Unit 1.7 1.8 1.9 V (aj) Analog LVDS supply voltage H_VREF (e) Host address and data reference voltage 2/3 x VTT - 1% 2/3 x VTT 2/3 x VTT + 1% V H_SWING (e) Host compensation reference voltage 0.3125x VTT - 1% 0.312 5x VTT 0.3125x VTT + 1% V SM_VREF (k) DDR2 reference voltage 0.49 x VCCSM 0.50 x VCCS M 0.51 x VCCSM V VCCA_LVDS Notes Reference Voltages Host Interface VIL_H (a, d, w) Host AGTL+ input low voltage -0.10 0 (2/3 x VTT) - 0.1 V VIH_H (a, d, w) Host AGTL+ input high voltage (2/3 x VTT) + 0.1 VTT (1.05) VTT + 0.1 V VOL_H (a, b, w) Host AGTL+ output low voltage 0.3125 x VTT) + 0.1 V VOH_H (a, b, w) Host AGTL+ output high voltage VTT V IOL_H (a, b, w) Host AGTL+ output low current VTTmax / (Rtermmi n Rpdmin) mA ILEAK_H (a, d, w) Host AGTL+ input leakage current 10 A CPAD (a, d, w) Host AGTL+ input capacitance 2.5 pF VOL_H (c) CMOS output low voltage 0.1 VTT V IOL = 1 mA VOH_H (c) CMOS output high voltage VTT V IOH = 1 mA VIL(DC) (l) DDR2 input low voltage SM_VRE F - 0.125 V VIH(DC) (l) DDR2 input high voltage VIL(AC) (i) DDR2 input low voltage VIH(AC) (i) DDR2 input high voltage VTT-0.1 1.2 0.9 VTT 5 DDR2 Interface 124 SM_VREF + 0.125 V SM_VRE F - 0.250 SM_VREF + 0.250 V V Datasheet DC Characteristics Table 28. Symbol DC Characteristics (Sheet 4 of 6) Signal Group Parameter VOL (i, j) DDR2 output low voltage VOH (i, j) DDR2 output high voltage ILEAK (i) Input leakage Current CI/O (i, j) DDR2 input/output pin capacitance Min Nom Max Unit Notes 0.3 V 2 V 2 1.5 1.0 10 A 4.0 pF 1.2 V 3, 4 20 mV 3 1.2 V 3, 4 150 mV 0.8 V 1.05 V PCI Express Interface 1.1 (includes PCI Express GFX and SDVO) VTX-DIFF P-P (f, g) Differential peak to peak output voltage VTX_CM-ACp (f, g) AC peak common mode output voltage ZTX-DIFF-DC (f, g) DC differential TX impedance VRX-DIFF p-p (f, g) Differential input peak to peak voltage VRX_CM-ACp (f, g) AC peak common mode input voltage 0.400 80 100 0.175 120 Clocks, Reset, and Miscellaneous Signals VIL (s) Input low voltage VIH (s) Input high voltage ILEAK (s) Input leakage current CIN (s) Input capacitance 3.0 VIL (t) Input low voltage -0.3 VIH (t) Input high voltage VCROSS (t) Crossing voltage VCROSS (t) Range of crossing points NA VSWING (t) Differential output swing 0.300 ILEAK (t) Input leakage current CPAD (t) Pad capacitance VOL (u) Output low voltage (CMOS outputs) VOH (u) Output high voltage (CMOS outputs) IOL (u) Output low current (CMOS outputs) IOH (u) Output high current (CMOS outputs) VIL (v) Input low voltage (DC) VIH (v) Input high voltage (DC) Datasheet 2.0 V 0.300 NA -5 0.95 1.2 10 A 6.0 pF V 5, 13, 14 1.15 V 5, 12, 13 0.550 V 6, 11, 15 0.140 V 6, 11, 9 V 5, 10 +5 A 5, 7 1.45 pF 5, 8 0.4 V 2.8 V 1 -1 0.8 1.55 mA @VOL_HI max mA @VOH_HI min V V 125 DC Characteristics Table 28. DC Characteristics (Sheet 5 of 6) Symbol Signal Group Parameter ILEAK (v) Input leakage current Min Nom Max Unit 10 A Notes CIN (v) Input capacitance 10 pF VIL (x) Input low voltage 0.8 V VIH (x) Input high voltage ILEAK (x) Input leakage current 10 CIN (x) Input capacitance 10 pF 450 mV 17 50 mV 17 1.375 V 17 50 mV 17 -3.5 -10 mA 17 1 10 A 17 0.277 V 2.0 V A LVDS Interface: Functional Operating Range (VCC=1.8 V5%) VOD (l) Differential output voltage VOD (l) Change in VOD between complementary output states VOS (l) Offset voltage VOS (l) Change in VOS between complementary output states IOs (l) Output short circuit current IOZ (l) Output TRI-STATE current 250 1.125 350 1.25 Controller Link VIL (al) Input low voltage VIH (al) Input high voltage ILEAK (al) Input leakage current 20 A CIN (al) Input capacitance 2.0 pF IOL (al) Output low current (CMOS outputs) 1.0 mA @VOL_HI max IOH (al) Output high current (CMOS outputs) mA @VOH_HI min VOL (al) Output low voltage (CMOS outputs) VOH (al) Output high voltage (CMOS outputs) 0.427 V 6 0.06 0.6 V V SDVO_CTRLDATA, SDVO_CTRLCLK VIL Input low voltage VIH Input high voltage ILEAK Input leakage current 10 A CIN Input capacitance 10.0 pF VOL Output low voltage 0.4 V 126 0.75 1.75 V V Datasheet DC Characteristics Table 28. DC Characteristics (Sheet 6 of 6) Symbol Signal Group Parameter Min Nom Max Unit Notes CRT_DDC_DATA, CRT_DDC_CLK, L_DDC_CLK, L_DDC_DATA, L_CRTL_CLK, L_CTRL_DATA, TV_DCONSEL_0, TV_DCONSEL_1, CLKREQ# VIL Input low voltage 0.9 VIH Input high voltage ILEAK Input leakage current 10 A CIN Input capacitance 10.0 pF VOL Output low voltage 0.4 V 0.9 V 2.1 V V L_VDDEN, L_BKLTEN, L_BKLTCTL, DFGT_VID[3:0], DFGT_VR_EN VIL Input low voltage VIH Input high voltage ILEAK Input leakage current 10 A CIN Input capacitance 10.0 pF VOL Output low voltage (CMOS outputs) 0.4 V VOH Output high voltage (CMOS outputs) 2.1 V 2.7 V CFG_RSVD[2:0], DPRSLPVR, PM_EXTTS#[1:0] VIL Input low voltage 0.9 V VIH Input high voltage ILEAK Input leakage current 10 A CIN Input capacitance 10.0 pF 0.3VCC V 2.1 V PM_DPRSTP# VCC = 1.05V VIL Input low voltage VIH Input high voltage ILEAK Input leakage current 10 A CIN Input capacitance 10.0 pF 0.7 VCC V NOTES: 2. Determined with 2x (G)MCH DDR2 buffer strength settings into a 50 to 0.5 x VCCSM (DDR2) test load. 3. Specified at the measurement point into a timing and voltage compliance test load as shown in transmitter compliance eye diagram of PCI Express specification and measured over any 250 consecutive TX Uls. Specified at the measurement point and measured over any 250 consecutive ULS. The test load shown in receiver compliance eye diagram of PCI Express specification. Should be used as the RX device when taking measurements. 4. For low voltage PCI Express (PCI Express Graphics/SDVO) interface: Symbol 5. Parameter Min Typ Max Unit RTT Termination resistance 50 55 61 RCN Buffer on resistance 22 25 28 Unless otherwise noted, all specifications in this table apply to all FSB frequencies. Datasheet 127 DC Characteristics 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Crossing voltage is defined as absolute voltage where rising edge of BCLK0 is equal to the falling edge of BCLK1. For Vin between 0 V and VH. Cpad includes die capacitance only. No package parasitics are included. VCROSS is defined as the total variation of all crossing voltages as defined in note 6. Measurement taken from differential waveform. Measurement taken from single-ended waveform. "Steady state" voltage, not including Overshoots or Undershoots. The maximum voltage including overshoot. The minimum voltage including undershoot. Only applies to the differential rising edge (Clock rising and Clock# falling). If a variable VRM is used the VCC_AXG should be 5% of the nominal setting (the setting shown is of 1.05 V). All LVDS active lanes must be terminated with 100- resistors for correct Vos performance and measurement. 12.2 CRT DAC DC Characteristics Table 29. CRT DAC DC Characteristics: Functional Operating Range (VCCADAC = 3.3 V 5%) Parameter Min DAC resolution Maximum luminance (full-scale) Typical Max 8 0.665 Minimum luminance LSB current 0.700 Units Bits 0.770 Notes (1) Measured at low frequency V (2, 4, 5) white video level voltage 0.000 V (3) Measured at DC. Black video level voltage 73.2 A (4, 5) Integral linearity (INL) -1.0 +1.0 LSB (6) Differential linearity (DNL) -1.0 +1.0 LSB (6) 6 % (7) Video channel-channel voltage amplitude mismatch Monotonicity Guaranteed NOTES: 1. Measured at each R, G, B termination according to the VESA Test Procedure - Evaluation of Analog Display Graphics Subsystems Proposal (Version 1, Draft 4, December 1, 2000). 2. Maximum steady-state amplitude. 3. Minimum steady-state amplitude. 4. Defined for a double 75- termination. 5. Set by external reference resistor value. 6. INL and DNL measured and calculated according to VESA video signal standards. 7. Max full-scale voltage difference among R, G, B outputs (percentage of steady-state full-scale voltage). 128 Datasheet DC Characteristics 12.3 TV DAC DC Characteristics Table 30. TV DAC DC Characteristics: Functional Operating Range (VCCATVDAC [A,B,C] = 3.3 V 5%) Parameter Min DAC resolution ENOB (Effective number of bits) Typica l Max Units 10 7.5 Notes Bits Measured at low frequency Bits @ NTSC/PAL Video BW Max luminance (full scale) 1.235 1.3 1.365 V For composite video signal Note: 1, 3, 4 Maximum luminance (full scale) 1.045 1.1 1.155 V For S-Video signal Note: 1, 3, 4 Maximum luminance (full scale) 0.665 0.7 0.735 V For component video signal Note: 1, 3, 4 Minimum luminance -0.1 0 +0.1 mV Measured at DC, Note: 2 Integral linearity (INL) -2.5 +2.5 LSB Note: 5 Differential linearity (DNL) -0.5 +0.5 LSB Note: 5 dB RMS @ NTSC/PAL video BW % Note: 6 SNR 48 Video channel-channel voltage amplitude mismatch -3 Monotonicity +3 Guaranteed NOTES: 1. Maximum steady-state amplitude. 2. Minimum steady-state amplitude. 3. Defined for a double 75- termination. 4. Set by external reference resistor value. 5. INL and DNL measured and calculated based on the method given in VESA video signal standards. 6. Maximum full-scale voltage difference among the outputs (percentage of steady-state full-scale voltage). Datasheet 129 DC Characteristics 130 Datasheet Clocking 13 Clocking 13.1 Overview The (G)MCH has a total of four PLLs that are used for many internal clocks. The PLLs are: * Host PLL--Generates the main core clocks in the host clock domain. Can also be used to generate memory and integrated graphics core clocks. Uses the Host clock (HPLL_CLK /HPLL_CLK#) as a reference. * PCI Express PLL--Generates all PCI Express related clocks, including the DMI that connects to the ICH. This PLL uses the 100 MHz (PEG_CLK / PEG_CLK#) as a reference. * Display PLL A--Generates the internal clocks for Display A or Display B. Uses the low voltage 96-MHz differential clock, DPLL_REF_CLK / DPLL_REF_CLK#, as a reference. * Display PLL B--Generates the internal clocks for Display A or Display B. Uses the low voltage 96-MHz differential clock, DPLL_REF_CLK / DPLL_REF_CLK#, as a reference. Also may optionally use DPLL_REF_SSCLK / DPLL_REF_SSCLK#as a reference for SSC support for LVDS display. 13.2 (G)MCH Reference Clocks Reference Input Clocks HPLL_CLK / HPLL_CLK# 133, 167, 200 Associated PLL Host / Memory / Graphics Core PEG_CLK / PEG_CLK# 100 MHz PCI Express / DMI PLL DPLL_REF_CLK / DPLL_REF_CLK# 96 MHz Display PLL A or B DPLL_REF_SSCLK / DPLL_REF_SSCLK# Datasheet Input Frequency 96 MHz (Non-SSC) 100 MHz (SSC) Display PLL B 131 Clocking 13.3 Host/Memory/Graphics Core Clock Frequency Support Table 31. Host/Memory/Graphics Clock Frequency Support for 1.05-V Core Voltage for the Mobile Intel GM965 and GL960 Express Chipsets Host (MHz) Memory (MHz) Display Clock (MHz) Render Clock (MHz) 533 DDR2 533 320 267(GM965/GL960)/320(GM965/ GL960)/400(GM965/GL960) 533 DDR2 533 200 267(GM965/GL960) 667 DDR2 533 333 267(GM965)/333(GM965) 667 DDR2 667 333 250(GM965)/333(GM965)/ 400(GM965)/500(GM965) 800 DDR2 533 320 267(GM965)/320(GM965)/ 400(GM965) 800 DDR2 667 333 250(GM965)/333(GM965)/ 400(GM965)/500(GM965) 800 DDR2 667 200 500(GM965) Note: All supported frequencies for GM965/GL960 apply for GME965/GLE960 respectively Table 32. Host/Memory/Graphics Clock Frequency Support for 1.05-V Core Voltage for the Mobile Intel GM965/GM965 (mini-note)/GM965 (sub-note), GL960 and PM965 Express Chipsets Note: SKU GM965 GM965 (mini-note) GM965 (sub-note) GL960 PM965 Max FSB (MHz) 800 800 533 533 800 Max Memory (MHz) DDR2 667 DDR2 533 DDR2 533 DDR2 533 DDR2 667 Max Display Clock (MHz) 333 320 320 320 N/A Recommended Max Render Clock (MHz) 500 320 267 400 N/A All supported frequencies for GM965/GL960 apply for GME965/GLE960 respectively 132 Datasheet (G)MCH Strapping Configuration 14 (G)MCH Strapping Configuration Table 33. (G)MCH Strapping Signals and Configuration Pin Name Strap Description Configuration Pull Up Rail Notes 1.05 V 1, 2, 3 1.05 V 1, 2, 3 1.05 V 1, 2, 3 1.05 V 1, 2,3 010 = FSB 800 MHz CFG[2:0] FSB Frequency Select 011 = FSB 667 MHz 001 = FSB 533 MHz Others: Reserved CFG[4:3] Reserved CFG5 DMI x2 Select CFG[8:6] Reserved CFG9 PCI Express Graphics Lane Reversal CFG[11:10] Reserved 0 = DMI x2 1 = DMI x4 (default) 0 = Lane Reversed 1 = Normal mode (default; lanes numbered in order) 00 = Reserved CFG[13:12] XOR/ALL-Z 01 = XOR Mode Enabled 10 = All-Z Mode Enabled 11 = Normal operation (default) CFG[15:14] Reserved CFG16 FSB Dynamic ODT CFG[18:17] Reserved CFG19 DMI Lane Reversal 0 = Dynamic ODT disabled 1, 2, 3 1 = Dynamic ODT enabled (default) 0 = Normal mode (default; lanes numbered in order) 3.3 V 1, 2, 3 3.3 V 1, 2, 3 2.5 V all 1 = Lane reversed CFG20 Concurrent SDVO / PCI Express SDVO_CTRL_DATA SDVO Present 0 = Only SDVO or PCI Express is operational (default) 1 = SDVO and PCI Express operate simultaneously through the PCI Express Graphics attach port 0 = No SDVO Card Present (default) 1 = SDVO Card Present NOTES: 1. All strap signals are sampled with respect to the leading edge of the (G)MCH Power OK (PWROK) signal. 2. Default values do not require pull-up/pull-down resistors. 3. Pull-up/Pull-down resistor value should be 4-k 5%. 4. No need for pull-up resistor if an SDVO Add In card is being use. Datasheet 133 (G)MCH Strapping Configuration 134 Datasheet Ballout and Package Information 15 Ballout and Package Information 15.1 (G)MCH Ballout Diagrams Figure 21. Ballout Diagram (Top View) Upper Left Quadrant BL BK BJ 51 50 49 VSS_SC B5 NC NC NC NC SB_DQ2 1 NC SB_DQ1 6 VSS SA_DQ1 3 VSS SB_DQ1 1 BC SB_DQ S#1 VSS SB_DQ9 BB AY VSS SB_DQ1 3 AW SB_DQ3 SB_DQ2 PWROK SB_DQ6 SB_DQ7 SB_DQ S0 AT SB_DQ1 SB_DQ4 SB_DQ5 41 SB_DQ2 SB_DQ2 SB_DQ2 2 3 8 VSS SA_DQ2 1 VSS VSS SA_DQ3 SA_DQ2 2 VSS SA_DM 1 SB_DQ SB_DQ SB_DQ3 S3 S#3 1 VSS SA_DQ S2 VSS SB_DQ0 CL_RST # SA_DQ5 VSS SA_DQ0 DMI_RX P0 VSS DMI_TX DMI_TX N3 P3 AK AJ AH VCC_R VCC_R PEG_R XR_DMI XR_DMI X#13 AG AF Datasheet VSS VSS PEG_R X13 DMI_TX DMI_TX P0 N0 PEG_R X12 VSS VSS VSS PEG_R PEG_TX PEG_TX X14 #15 15 PEG_R PEG_R X#12 X#14 VSS VCC_S VCC_S M M SB_MA1 VCC_S M VCC_S VCC_S M M VCCA_ SB_MA7 SM_CK VCC_S M VCCA_ SM_CK VSS SA_DQ S#3 VCC_S M VCC_S VCC_S M M VSS VCC_S M SM_CK E1 SA_DM 3 SA_DQ2 VCC_S 7 M SA_DQ2 4 VSS VSS VCC_S M VCC VSS SB_MA6 SA_MA9 SB_MA8 SM_CK #0 VSS VCC_A XM VCC_A XM_NC TF VCC_A XM_NC TF VSS SM_CK 0 VCC_S VCC_S M M VCC SM_CK SA_MA1 E0 1 VCC_S M VSS VCC_A XD VCC_A VCC_A VCC_A XM XD XD VCC_A XM_NC TF VCC_A XM_NC TF VCC_A XM_NC TF VCC_A XM_NC TF VSS VCC_A VSS_N XD_NC CTF TF VCC_A VSS_N XM_NC CTF TF VCC_A XG_NC TF VCC_A VCC_A VCC_A XM_NC XM_NC XM_NC TF TF TF VCC_A VCC_A VCC_N XM_NC XM_NC CTF TF TF VCC_A XM_NC TF VCC_A XM_NC TF VCC_A XM_NC TF VCC_A XM_NC TF VCC_A XM_NC TF VCC_A XM_NC TF VCC_N VCC_N VCC_N CTF CTF CTF VCC_N CTF VCC_A XM VSS VSS VCC_N VCC_N CTF CTF VCC_N CTF VSS VCC VSS VCC VCC_A XM VCC_N VCC_N VCC_N CTF CTF CTF VCC_N CTF VCC VCC VCC VCC VCC_A XG VCC_N VSS_N CTF CTF VCC_N CTF VCC VSS VSS VSS VCC_A XG VCC_N VCC_N CTF CTF VSS_N CTF VSS RSVD DMI_RX DMI_RX P1 N1 PEG_TX #13 PEG_TX 13 VSS VCC_S M RSVD DMI_TX DMI_TX N2 P2 VSS VCC_S M SA_DQ3 0 SA_DQ2 SA_DQ3 6 1 DMI_TX DMI_TX P1 N1 PEG_R PEG_R X15 X#15 VSS SA_BS2 SA_DQ S3 DMI_RX DMI_RX N2 P2 VSS SA_MA1 2 SA_MA6 VCC_S M_LF2 VSS 26 SA_MA3 VCC_S M CL_DAT A VCC_D MI VSS VCC_S VCC_S M M VSS VSS VCC_S M 27 SA_MA5 SA_MA2 VCC_S M VCC_N VCC_N CTF CTF VSS VSS SA_MA1 4 VCC_S M VSS DMI_RX DMI_RX DMI_RX N0 N3 P3 28 SA_MA8 SB_MA1 1 SA_DQ2 9 SA_DQ4 29 SB_MA9 VSS VSS 30 VCC_S VCC_S M M VSS SA_DQ2 SA_DQ2 8 5 CL_PW SA_DQ6 ROK 31 VCC_S VCC_S VCC_S M M M VSS VSS 32 VCC_S M SM_CK VCC_S SB_BS2 E4 M VSS AL VSS VSS 33 SM_RC OMP_V OL SM_RC VCC_S VCC_S VCC_S VCC_S OMP_V M M M M OH SB_DQ2 SB_DQ2 6 7 VSS VSS 34 SM_CK E3 VSS SA_DQ SA_DQ SA_DM S#0 S0 0 35 SB_DQ3 0 VCC_S VCC_S M M SB_MA1 2 VSS 36 SA_DQ1 VCC_S 9 M_LF3 SA_DM 2 VCC_S SA_DQ1 SA_DQ1 M_LF1 6 SA_DQ7 37 VSS SA_DQ2 3 SA_DQ1 SA_DQ1 5 7 VSS 38 RSVD SA_DQ1 8 SA_DQ8 VSS SB_DQ2 SB_DQ2 4 9 SA_DQ2 0 VSS 39 SB_DM 3 VSS SA_DQ1 0 SA_DQ S#1 40 SB_DQ2 5 VSS CL_VRE CL_CLK F AM 42 SA_DQ2 SB_DM SM_VR 0 EF VSS AP AN SB_DQ S#0 VSS VSS SA_DQ1 2 VSS SB_DQ1 SB_DQ1 SB_DQ8 2 0 VSS 43 SB_DQ1 9 SA_DQ S#2 BA AV VSS 44 SA_DQ1 SB_DQ1 SB_DQ1 1 7 8 SA_DQ S1 BD AR 45 SB_DQ S#2 SB_DQ2 SB_DQ SB_DM 0 S2 2 VSS SB_DQ SB_DM S1 1 AU 46 SB_DQ1 SB_DQ1 SA_DQ9 4 5 BF BE 47 VSS SA_DQ1 4 BH BG 48 RSVD VCC_N CTF RSVD VCC_N CTF VCC VSS VSS 135 Ballout and Package Information Figure 22. 25 24 Ballout Diagram (Top View) Upper Right Quadrant 23 SA_MA4 22 21 20 VSS VSS VCC_S VCC_S M_CK M_CK SA_MA7 VCC_S VCC_S M_CK M_CK 19 RSVD RSVD SA_BS1 VSS SB_MA4 SB_MA5 SB_MA1 4 SM_CS #0 RSVD VSS VSS SM_CK 3 VSS VSS VSS VCC_A XD VCC_A XD VSS VSS SB_BS1 VSS SA_BS0 SM_CK #1 SA_WE # SM_CS #1 VSS SM_CK #4 RSVD VCCA_ SB_MA3 SM SM_CK 4 RSTIN# VCCA_ SM VCC_A VCC_A XM XM VSS VCC_A XM VCC_A VCC_A XG XG VCC_A XG_NC TF VCC_A XG_NC TF VCC_A VSS VSS XG_NC TF VCC_A VCC_A VSS XG_NC XG TF VCC_A VCC_A VCC_A XG_NC XG XG TF VCC_A XG_NC TF VCC_A XG_NC TF VCC_A XG_NC TF VCC_A XG_NC TF 10 9 VSS 8 SB_DQ4 1 SB_DQ4 0 7 6 SB_DQ S5 VSS SB_DQ S#5 VSS 3 2 1 SB_DQ4 3 5 NC NC VSS_SC B4 SB_DQ4 2 SB_DQ5 2 NC NC BK SB_DQ5 5 NC BJ VSS SB_DQ5 0 SB_DQ4 SB_DM SB_DQ4 6 5 7 VSS SA_DQ4 4 SA_DQ SA_DQ SB_DQ4 S#5 S5 9 SA_DM 5 SA_DQ4 1 VSS SB_DQ3 SB_DQ3 SB_DQ3 6 8 5 SA_DQ S4 VSS SA_DQ3 8 SA_DM 4 SB_RAS # SA_DQ3 2 SA_DQ4 SA_DQ4 2 6 VSS VCC_S SB_DQ5 M_LF5 4 SA_DQ4 7 VSS SA_DQ5 3 SA_DQ4 8 SB_DQ5 6 SA_DQ3 4 SA_DQ4 3 SA_DQ4 SA_DQ5 SA_DM 9 2 6 SA_DQ4 VCC_S 5 M_LF6 VSS VSS SM_VR EF SA_DQ3 5 SA_DQ3 3 RSVD SA_DQ3 7 RSVD VSS VSS SA_DQ6 0 SA_DQ5 VCC_S SA_DQ5 1 M_LF7 0 SA_DQ5 SA_DQ5 6 5 VSS VSS VCC_A XG_NC TF SA_DQ6 SA_DQ5 SA_DQ6 3 9 1 RSVD VSS RSVD VSS VSS SA_DQ6 SA_DQ5 HPLL_C 2 8 LK# SA_DM 7 HPLL_C LK VSS VSS 136 VSS VCC_A XG VSS VCC_A XG_NC TF VCC_A VSS_N XG_NC CTF TF AR AP VSS AN AM VSS AL AK H_D#50 VCC_A XG_NC TF VSS H_D#63 H_D#53 VSS H_DSTB N#3 H_DSTB H_D#48 P#3 VSS H_D#58 H_D#56 H_D#54 H_D#49 VSS H_D#55 H_D#61 H_D#59 VSS H_D#47 VSS AU AT SB_DQ5 8 VCCA_ MPLL VCCA_ HPLL AW AV VSS SA_DQ SA_DQ S7 S#7 SA_DQ5 VCCD_ 7 HPLL VSS BA AY VSS SB_DQ5 SB_DQ6 9 3 SA_DQ5 4 VSS SB_DQ6 2 BC BB VSS SB_DQ SB_DQ S#7 S7 VSS VCCA_ VSS_N SM_NC CTF TF VCC_A VCC_A XG_NC XG_NC TF TF VCC_A VSS_N XG_NC CTF TF VCC_A VCC_A XG_NC XG_NC TF TF VCC_A VSS_N XG_NC CTF TF VCC_A VCC_A XG_NC XG_NC TF TF VCC_A VCC_A XG_NC XG_NC TF TF SB_DM 7 BE BD SB_DQ6 SB_DQ6 1 0 SA_DQ3 6 VSS VSS VSS BG BF VSS SB_DQ5 SA_DQ 7 S6 SA_DQ3 9 VSS SB_DQ S6 SB_DQ5 SA_DQ 1 S#6 VSS VSS SB_DQ5 3 VSS BL BH VSS SB_DQ4 SB_DM SB_DQ 8 6 S#6 SM_CS SB_DQ3 SB_DQ3 SA_DQ4 #3 7 3 0 SA_DQ S#4 4 VSS VSS VCCA_ VCCA_ VCCA_ SM SM SM VCCA_ SM_NC TF VCC_A XG_NC TF SB_DQ S4 SB_MA1 SB_DQ3 3 9 VCC_A XG VCC_A VSS_N XG_NC CTF TF VCC_A VCC_A XM_NC XG_NC TF TF VSS VSS VCCA_ VCCA_ VCCA_ SM SM SM VCC_A VSS_N XG_NC CTF TF VCC_A VCC_A XG_NC XG_NC TF TF 11 VSS SB_DM 4 SA_RAS SB_CAS SM_OD # # T3 VSS 12 SM_RC SB_DQ3 SB_DQ SB_DQ3 SB_DQ4 SB_DQ4 OMP# 2 S#4 4 5 4 SB_MA1 SM_CS 0 #2 SB_RC SB_BS0 VEN# VCC_A XG_NC TF VCC_A XG_NC TF VSS 13 VSS VSS SA_RC VEN# VCC_A XG_NC TF VCC_A XG_NC TF 14 VCC_S M_LF4 SM_CK 1 VSS 15 SM_RC OMP SA_MA1 SM_OD SM_OD 3 T1 T2 SA_MA1 SB_WE SB_MA0 0 # RSVD 16 VSS SA_MA1 VCC_A VCCA_ VCCA_ XD SM SM VCC_A XG_NC TF VCC_A XG_NC TF VSS RSVD VSS SM_CK #3 RSVD SM_OD T0 RSVD RSVD VSS 17 SA_CAS # RSVD SA_MA0 RSVD RSVD SB_MA2 18 VSS AJ H_D#62 VTTLF3 VSS AH AG AF Datasheet Ballout and Package Information Figure 23. PEG_TX PEG_TX 14 #14 AE AD VCC_PE G VSS PEG_TX 10 VSS PEG_TX PEG_TX 11 #11 AC AB Ballout Diagram (Top View) Lower Left Quadrant VSS VSS PEG_R PEG_TX X#10 12 PEG_TX PEG_R #10 X10 VSS VSS PEG_R PEG_TX X#11 #9 PEG_TX PEG_R #12 X11 VSS VCC_N CTF VSS VCC_AX G VCC_N VCC_N CTF CTF VCC_N CTF VCC VCC VCC_AX VCC_AX G G VCC_N CTF VSS VSS VCC_AX G VSS VSS VSS VCC_AX G VSS VCC_AX G VCC_AX G PEG_TX 9 PEG_R PEG_R X#8 X8 VCC_N VCC_N VSS_NC CTF CTF TF VCC_N VCC_N CTF CTF AA VSS Y W VCCA_P EG_PLL PEG_TX PEG_TX 4 #4 PEG_TX PEG_TX #3 3 VSS PEG_R PEG_R X#1 X1 VSS B A VSS VSS PEG_R PEG_TX X3 5 PEG_TX PEG_R 2 X#3 VSS VSS VSS VSS PEG_R X#2 PEG_TX #0 VSS PEG_R X2 PEG_TX 0 VSS VSS PEG_C OMPI PEG_C OMPO LVDS_V LVDS_V REFH REFL VCC_AX G_NCTF VCC_N VCC_N VSS_NC CTF CTF TF VCC_N VCC_N VSS_NC CTF CTF TF VCC_AX VCC_AX G_NCTF G_NCTF VCC_AX G_NCTF VCC_N VCC_N CTF CTF PEG_TX VSS_NC 1 TF VSS VSS VSS LVDS_I BG LVDSB_ DATA#0 NC NC NC 51 50 49 LVDSA_ LVDSA_ DATA3 CLK# 48 VSS L_VDD_ EN VCCD_L L_BKLT VDS _CTRL PM_EXT _TS#1 VSS VSS LVDSB_ DATA#1 LVDSB_ DATA1 47 VSS PM_BM ICH_SY CLKRE _BUSY# NC# Q# LVDSB_ CLK VSS LVDSA_ LVDSB_ CLK DATA3 DPLL_R EF_CLK # VSS LVDSB_ LVDSB_ DATA#2 DATA#3 DPLL_R VSSA_L VCC_H GFX_VI EF_CLK VDS V D3 46 45 VSS 44 43 VSS VCC_H V VCCA_L VDS 42 41 VSS GFX_VI D1 40 VSS VSS 39 RSVD VSS RSVD TEST1 VSS 38 37 VSS 36 35 CFG0 VSS VCCD_ QDAC VCCD_T VDAC VSS CFG1 VSS CFG18 CRT_G REEN VCC_SY NC CRT_G REEN# CRT_BL UE TVC_RT N TVC_DA C VSS TVB_RT N VSS VSS TVB_DA C CRT_HS YNC CRT_RE D TVA_RT N CRT_VS YNC CRT_RE D# VSS TVA_DA C VSS VCCA_T VB_DAC VSS CRT_BL UE# VSS VSS VSS RSVD RSVD VSS VSS VSS VCC_AX G_NCTF VSS_NC TF VSS VCC CRT_D DC_CLK L_DDC_ DATA GFX_VI L_DDC_ D2 CLK VCC_N VSS_NC CTF TF VCC_N CTF VCCD_ CRT GFX_VR GFX_VI _EN D0 VSS VCC_TX _LVDS CFG19 VSS L_CTRL L_CTRL _DATA _CLK LVDSB_ CLK# LVDSB_ DATA2 RSVD SDVO_ CTRL_C LK CRT_D DPRSLP DC_DAT VR A L_BKLT _EN VSS TEST2 PM_EXT CFG20 _TS#0 VSS LVDSA_ DATA#3 RSVD VSS PM_DP RSTP# VCCD_L VDS LVDSB_ DATA0 VSS VSS_SC B6 VSS TV_DC ONSEL1 RSVD SDVO_ CTRL_D ATA LVDSA_ LVDSA_ DATA#2 DATA2 VSS VCC_N VCC_N VCC_N CTF CTF CTF VCC_N VCC_N CTF CTF TV_DC ONSEL0 PEG_CL PEG_CL K# K VSS DPLL_R DPLL_R VCCA_ EF_SSC EF_SSC DPLLB LK LK# VCCA_ DPLLA Datasheet VCC_AX VCC_AX G_NCTF G_NCTF VSS LVDS_V BG VSS VSS NC VCC_N VCC_N VCC_AX CTF CTF G_NCTF RSVD VSS VSS VCC_AX G VCC_N VCC_N VCC_N CTF CTF CTF PEG_R PEG_TX X#5 #1 PEG_TX PEG_R #5 X5 VCC_N CTF VSS PEG_TX #8 RSVD LVDSA_ LVDSA_ DATA#1 DATA1 D C PEG_R PEG_TX X#7 8 VSS LVDSA_ LVDSA_ DATA#0 DATA0 F E VSS VSS PEG_TX PEG_R 6 X7 PEG_R PEG_R X#0 X0 H G VSS VCCA_P VSSA_P EG_BG EG_BG K J PEG_R PEG_TX X#6 #6 VSS M L VSS PEG_TX PEG_R #7 X6 VCCD_ PEG_TX PEG_PL #2 L VSS P N VSS PEG_R PEG_R X#4 X4 T R PEG_R PEG_TX X9 7 VCC_PE VCC_PE G G V U VSS VCC_PE VCC_PE PEG_R G G X#9 VCC_AX G VSS_NC VCC_N VCC_N TF CTF CTF VSS CRT_TV O_IREF VSS VCCA_ VSSA_D RSVD CRT_DA AC_BG C VCCA_ CRT_DA C 34 33 32 VSS VSS VCCA_ DAC_B G 31 30 29 VCCA_T VCCA_T VC_DA VB_DAC C VCCA_T VC_DA C 28 27 26 137 Ballout and Package Information Figure 24. Ballout Diagram (Top View) Lower Right Quadrant VSS VCC_A VCC_A XG XG VSS VCC_A VCC_A VCC_A XG_NC XG XG TF VCC_A VCC_A VSS XG_NC XG TF VCC_A VCC_A XG XG VCC_A XG VSS VSS VCC_A XG VCC_A XG_NC TF VCC_A XG_NC TF VCC_A VSS_N XG CTF VSS VCC_A VCC_A XG_NC XG_NC TF TF VSS_N CTF VCC_A XG_NC TF VCC_A XG_NC TF VCC_A VSS_N XG CTF VCC_A VCC_A VCC_A XG_NC XG_NC XG_NC TF TF TF VCC_A XG_NC TF VCC_A XG_NC TF VCC_A XG_NC TF VCC_A XG_NC TF VCC_A XG_NC TF VCC_A XG_NC TF H_DINV #3 H_D#52 H_D#37 VSS H_D#39 VCC_A XG_NC TF VCC_A XG_NC TF VCC_A XG CFG10 VSS CFG2 VSS VSS CFG15 VSS CFG8 VSS VSS H_ADST B#1 CFG7 VSS VCCA_T VA_DA C VCCA_T VA_DA C VSS 138 24 VSS VCC_A XG H_A#26 H_A#15 H_A#10 VCC_A XF VSS VCC_A XF 22 21 VSS H_A#32 VSS VTT H_D#36 H_D#44 H_D#46 H_D#28 H_D#18 H_D#27 H_D#17 H_D#25 VTT VTT H_REQ #0 H_A#14 VSS VTT VTT VTT VTT H_D#24 VTT VTT 19 17 H_D#12 H_D#8 H_A#6 H_D#10 VSS H_A#3 VSS VSS VSS H_DSTB P#2 VSS H_D#30 AE VSS AD AC AB VTT VSS RSVD H_D#15 VSS VTT VTT VTT VTT VTT VTT VTT VSS VSS P H_D#23 H_D#26 H_D#31 N H_D#20 H_D#16 M VSS H_DINV #0 VSS H_DPW H_D#4 R# H_LOC K# H_ADS# VSS H_D#13 H_D#2 VSS 15 VSS H_A#5 H_DBS Y# H_REQ #4 H_A#4 VSS H_REQ #2 VSS 14 13 12 11 H_AVR EF H_DEFE R# H_BNR# H_HITM # H_DVR EF 10 9 8 VSS VTTLF1 NC VSS_SC B1 4 3 J G F NC E D H_SWIN VSS_SC G B2 5 L H VSS H_RCO VSS_SC MP B3 VSS 6 R K H_D#21 VSS H_TRD H_CPU Y# RST# 7 VSS H_D#7 VTTLF2 H_D#0 U T VTT H_D#9 H_D#1 H_CPU H_HIT# SLP# H_RS#2 H_RS#1 VSS H_D#5 H_D#6 H_BPRI # VSS VSS H_A#7 H_A#11 VSS VSS H_REQ H_RS#0 #1 H_DINV #1 V VTT H_DSTB H_DSTB N#1 P#1 VSS RSVD W VTT VSS H_DRD Y# Y H_SCO H_SCO MP# MP VSS H_D#22 H_DSTB H_D#3 N#0 VSS VSS VSS H_BRE Q# VSS 16 H_DSTB N#2 H_D#43 H_DSTB P#0 H_REQ #3 VSS 18 VSS H_A#9 VSS VSS VSS VSS H_D#29 H_D#11 H_A#34 H_A#27 H_A#29 H_A#20 H_A#30 H_A#16 H_A#13 H_A#33 20 H_A#25 H_A#8 H_A#23 VCC_A XF 23 VSS RSVD CFG9 H_D#33 H_D#45 VSS H_D#14 H_ADST B#0 H_A#31 CFG3 VSS VSS VTT H_A#12 CFG14 H_A#28 CFG4 VSS 25 H_A#22 VSS CFG13 VTT VCC_A XG H_A#24 H_A#21 CFG5 VSS VSS H_A#17 CFG12 H_D#60 H_D#19 H_A#18 CFG16 CFG11 H_D#35 VSS H_D#41 H_A#19 THERM H_A#35 TRIP# CFG6 VSS H_D#57 VSS AA VCC_A XG_NC TF VCC_A XG_NC TF VCC_A VCC_A XG_NC XG_NC TF TF VSS CFG17 VSS VCC_A VCC_A XG_NC XG_NC TF TF VCC_A VCC_A XG_NC XG_NC TF TF VCC_A VCC_A VCC_A XG_NC XG_NC XG_NC TF TF TF H_D#51 H_D#34 H_D#40 H_D#42 VCC_A VCC_A XG XG VCC_A VCC_A VCC_A XG_NC XG_NC XG_NC TF TF TF VCC_A VCC_A VSS_N XG_NC XG_NC CTF TF TF VCC_A VCC_A VCC_A VCC_A XG_NC XG_NC XG_NC XG_NC TF TF TF TF VSS H_DINV H_D#32 H_D#38 #2 C B A 2 1 Datasheet Ballout and Package Information 15.2 Ball List (Listed by Interface) 15.2.1 Analog TV-out Signal TV_DCONSEL0 15.2.2 Signal Ball F27 TVC_DAC K27 TV_DCONSEL1 P33 TVB_DAC G27 TVC_RTN L27 TVA_DAC E27 TVB_RTN J27 CRT DAC Ball Signal Ball Signal Ball CRT_BLUE H32 CRT_GREEN# J29 CRT_RED# E29 CRT_BLUE# G32 CRT_HSYNC F33 CRT_TVO_IREF C32 CRT_GREEN K29 CRT_RED F29 CRT_VSYNC E33 DDC and GMBus Ball Signal Ball Signal Ball CRT_DDC_CLK K33 L_CTRL_DATA E40 SDVO_CTRL_CLK H35 CRT_DDC_DATA G35 L_DDC_CLK C37 SDVO_CTRL_DATA K36 L_CTRL_CLK E39 L_DDC_DATA D35 DMI Signal Datasheet Ball TVA_RTN Signal 15.2.4 Signal M35 Signal 15.2.3 Ball Ball Signal Ball Signal Ball DMI_RXN0 AN47 DMI_RXP2 AN41 DMI_TXN3 AM44 DMI_RXN1 AJ38 DMI_RXP3 AN45 DMI_TXP0 AJ47 DMI_RXN2 AN42 DMI_TXN0 AJ46 DMI_TXP1 AJ42 DMI_RXN3 AN46 DMI_TXN1 AJ41 DMI_TXP2 AM39 DMI_RXP0 AM47 DMI_TXN2 AM40 DMI_TXP3 AM43 DMI_RXP1 AJ39 139 Ballout and Package Information 15.2.5 Host Interface Signal 140 Ball Signal Ball Signal Ball H_A#10 G17 H_D#13 H5 H_D#56 AJ6 H_A#11 C14 H_D#14 P13 H_D#57 AE7 H_A#12 K16 H_D#15 K9 H_D#58 AJ7 H_A#13 B13 H_D#16 M2 H_D#59 AJ2 H_A#14 L16 H_D#17 W10 H_D#6 G4 H_A#15 J17 H_D#18 Y8 H_D#60 AE5 H_A#16 B14 H_D#19 V4 H_D#61 AJ3 H_A#17 K19 H_D#2 G7 H_D#62 AH2 H_A#18 P15 H_D#20 M3 H_D#63 AH13 H_A#19 R17 H_D#21 J1 H_D#7 F3 H_A#20 B16 H_D#22 N5 H_D#8 N8 H_A#21 H20 H_D#23 N3 H_D#9 H2 H_A#22 L19 H_D#24 W6 H_DBSY# C10 H_A#23 D17 H_D#25 W9 H_DEFER# D6 H_A#24 M17 H_D#26 N2 H_DINV#0 K5 H_A#25 N16 H_D#27 Y7 H_DINV#1 L2 H_A#26 J19 H_D#28 Y9 H_DINV#2 AD13 H_A#27 B18 H_D#29 P4 H_DINV#3 AE13 H_A#28 E19 H_D#3 M6 H_DPWR# H8 H_A#29 B17 H_D#30 W3 H_DRDY# K7 H_A#3 J13 H_D#31 N1 H_DSTBN#0 M7 H_A#30 B15 H_D#32 AD12 H_DSTBN#1 K3 H_A#31 E17 H_D#33 AE3 H_DSTBN#2 AD2 H_A#32 C18 H_D#34 AD9 H_DSTBN#3 AH11 H_A#33 A19 H_D#35 AC9 H_DSTBP#0 L7 H_A#34 B19 H_D#36 AC7 H_DSTBP#1 K2 H_A#35 N19 H_D#37 AC14 H_DSTBP#2 AC2 H_A#4 B11 H_D#38 AD11 H_DSTBP#3 AJ10 H_A#5 C11 H_D#39 AC11 H_DVREF A9 H_A#6 M11 H_D#4 H7 H_HIT# E4 H_A#7 C15 H_D#40 AB2 H_HITM# C6 H_A#8 F16 H_D#41 AD7 H_LOCK# G10 H_A#9 L13 H_D#42 AB1 H_RCOMP C2 H_ADS# G12 H_D#43 Y3 H_REQ#0 M14 H_ADSTB#0 H17 H_D#44 AC6 H_REQ#1 E13 H_ADSTB#1 G20 H_D#45 AE2 H_REQ#2 A11 Datasheet Ballout and Package Information Signal 15.2.6 Ball Ball H_D#46 AC5 H_REQ#3 H13 H_BNR# C8 H_D#47 AG3 H_REQ#4 B12 H_BPRI# E8 H_D#48 AJ9 H_RS#0 E12 H_BREQ# F12 H_D#49 AH8 H_RS#1 D7 H_CPURST# B6 H_D#5 H3 H_RS#2 D8 H_CPUSLP# E5 H_D#50 AJ14 H_SCOMP W1 H_D#0 E2 H_D#51 AE9 H_SCOMP# W2 H_D#1 G2 H_D#52 AE11 H_SWING B3 H_D#10 M10 H_D#53 AH12 H_TRDY# B7 H_D#11 N12 H_D#54 AJ5 THERMTRIP# N20 H_D#12 N9 H_D#55 AH5 LVDS Ball Signal Ball Signal Ball L_BKLT_CTRL J40 LVDSA_DATA#0 G51 LVDSB_CLK# D44 L_BKLT_EN H39 LVDSA_DATA#1 E51 LVDSB_DATA#0 G44 L_VDD_EN K40 LVDSA_DATA#2 F49 LVDSB_DATA#1 B47 LVDS_IBG L41 LVDSA_DATA#3 C48 LVDSB_DATA#2 B45 LVDS_VBG L43 LVDSA_DATA0 G50 LVDSB_DATA#3 B44 LVDS_VREFH N41 LVDSA_DATA1 E50 LVDSB_DATA0 E44 LVDS_VREFL N40 LVDSA_DATA2 F48 LVDSB_DATA1 A47 LVDSA_CLK C45 LVDSA_DATA3 D47 LVDSB_DATA2 A45 LVDSA_CLK# D46 LVDSB_CLK E42 LVDSB_DATA3 C44 Intel(R) Management Engine Interface Ball Signal Ball CL_CLK AM49 CL_PWROK AT43 CL_DATA AK50 CL_RST# AN49 Signal CL_VREF Ball AM50 Memory Interface Signal SA_BS0 Datasheet Signal B9 Signal 15.2.8 Ball H_AVREF Signal 15.2.7 Signal Ball BB19 Signal SA_DQS#6 Ball BC1 Signal SB_DQ47 Ball BJ6 SA_BS1 BK19 SA_DQS#7 AP2 SB_DQ48 BF4 SA_BS2 BF29 SA_DQS0 AT46 SB_DQ49 BH5 141 Ballout and Package Information Signal 142 Ball Signal Ball Signal Ball SA_CAS# BL17 SA_DQS1 BE48 SB_DQ5 AN50 SA_DM0 AT45 SA_DQS2 BB43 SB_DQ50 BG1 SA_DM1 BD44 SA_DQS3 BC37 SB_DQ51 BC2 SA_DM2 BD42 SA_DQS4 BB16 SB_DQ52 BK3 SA_DM3 AW38 SA_DQS5 BH6 SB_DQ53 BE4 SA_DM4 AW13 SA_DQS6 BB2 SB_DQ54 BD3 SA_DM5 BG8 SA_DQS7 AP3 SB_DQ55 BJ2 SA_DM6 AY5 SA_MA0 BJ19 SB_DQ56 BA3 SA_DM7 AN6 SA_MA1 BD20 SB_DQ57 BB3 SA_DQ0 AR43 SA_MA10 BC19 SB_DQ58 AR1 SA_DQ1 AW44 SA_MA11 BE28 SB_DQ59 AT3 SA_DQ10 BG47 SA_MA12 BG30 SB_DQ6 AV50 SA_DQ11 BJ45 SA_MA13 BJ16 SB_DQ60 AY2 SA_DQ12 BB47 SA_MA14 BJ29 SB_DQ61 AY3 SA_DQ13 BG50 SA_MA2 BK27 SB_DQ62 AU2 SA_DQ14 BH49 SA_MA3 BH28 SB_DQ63 AT2 SA_DQ15 BE45 SA_MA4 BL24 SB_DQ7 AV49 SA_DQ16 AW43 SA_MA5 BK28 SB_DQ8 BA50 SA_DQ17 BE44 SA_MA6 BJ27 SB_DQ9 BB50 SA_DQ18 BG42 SA_MA7 BJ25 SB_DQS#0 AU50 SA_DQ19 BE40 SA_MA8 BL28 SB_DQS#1 BC50 SA_DQ2 BA45 SA_MA9 BA28 SB_DQS#2 BL45 SA_DQ20 BF44 SA_RAS# BE18 SB_DQS#3 BK38 SA_DQ21 BH45 SA_RCVEN# AY20 SB_DQS#4 BK12 SA_DQ22 BG40 SA_WE# BA19 SB_DQS#5 BK7 SA_DQ23 BF40 SB_BS0 AY17 SB_DQS#6 BF2 SA_DQ24 AR40 SB_BS1 BG18 SB_DQS#7 AV3 SA_DQ25 AW40 SB_BS2 BG36 SB_DQS0 AT50 SA_DQ26 AT39 SB_CAS# BE17 SB_DQS1 BD50 SA_DQ27 AW36 SB_DM0 AR50 SB_DQS2 BK46 SA_DQ28 AW41 SB_DM1 BD49 SB_DQS3 BK39 SA_DQ29 AY41 SB_DM2 BK45 SB_DQS4 BJ12 SA_DQ3 AY46 SB_DM3 BL39 SB_DQS5 BL7 SA_DQ30 AV38 SB_DM4 BH12 SB_DQS6 BE2 SA_DQ31 AT38 SB_DM5 BJ7 SB_DQS7 AV2 SA_DQ32 AV13 SB_DM6 BF3 SB_MA0 BC18 SA_DQ33 AT13 SB_DM7 AW2 SB_MA1 BG28 SA_DQ34 AW11 SB_DQ0 AP49 SB_MA10 BG17 SA_DQ35 AV11 SB_DQ1 AR51 SB_MA11 BE37 Datasheet Ballout and Package Information Signal Datasheet Ball Signal Ball Signal Ball SA_DQ36 AU15 SB_DQ10 BA49 SB_MA12 BA39 SA_DQ37 AT11 SB_DQ11 BE50 SB_MA13 BG13 SA_DQ38 BA13 SB_DQ12 BA51 SB_MA14 BE24 SA_DQ39 BA11 SB_DQ13 AY49 SB_MA2 BG25 SA_DQ4 AR41 SB_DQ14 BF50 SB_MA3 AW17 SA_DQ40 BE10 SB_DQ15 BF49 SB_MA4 BF25 SA_DQ41 BD10 SB_DQ16 BJ50 SB_MA5 BE25 SA_DQ42 BD8 SB_DQ17 BJ44 SB_MA6 BA29 SA_DQ43 AY9 SB_DQ18 BJ43 SB_MA7 BC28 SA_DQ44 BG10 SB_DQ19 BL43 SB_MA8 AY28 SA_DQ45 AW9 SB_DQ2 AW50 SB_MA9 BD37 SA_DQ46 BD7 SB_DQ20 BK47 SB_RAS# AV16 SA_DQ47 BB9 SB_DQ21 BK49 SB_RCVEN# AY18 SA_DQ48 BB5 SB_DQ22 BK43 SB_WE# BC17 SA_DQ49 AY7 SB_DQ23 BK42 SM_CK#0 AW30 SA_DQ5 AR45 SB_DQ24 BJ41 SM_CK#1 BA23 SA_DQ50 AT5 SB_DQ25 BL41 SM_CK#3 AW25 SA_DQ51 AT7 SB_DQ26 BJ37 SM_CK#4 AW23 SA_DQ52 AY6 SB_DQ27 BJ36 SM_CK0 AV29 SA_DQ53 BB7 SB_DQ28 BK41 SM_CK1 BB23 SA_DQ54 AR5 SB_DQ29 BJ40 SM_CK3 BA25 SA_DQ55 AR8 SB_DQ3 AW51 SM_CK4 AV23 SA_DQ56 AR9 SB_DQ30 BL35 SM_CKE0 BE29 SA_DQ57 AN3 SB_DQ31 BK37 SM_CKE1 AY32 SA_DQ58 AM8 SB_DQ32 BK13 SM_CKE3 BD39 SA_DQ59 AN10 SB_DQ33 BE11 SM_CKE4 BG37 SA_DQ6 AT42 SB_DQ34 BK11 SM_CS#0 BG20 SA_DQ60 AT9 SB_DQ35 BC11 SM_CS#1 BK16 SA_DQ61 AN9 SB_DQ36 BC13 SM_CS#2 BG16 SA_DQ62 AM9 SB_DQ37 BE12 SM_CS#3 BE13 SA_DQ63 AN11 SB_DQ38 BC12 SM_ODT0 BH18 SA_DQ7 AW47 SB_DQ39 BG12 SM_ODT1 BJ15 SA_DQ8 BB45 SB_DQ4 AN51 SM_ODT2 BJ14 SA_DQ9 BF48 SB_DQ40 BJ10 SM_ODT3 BE16 SA_DQS#0 AT47 SB_DQ41 BL9 SM_RCOMP BL15 SA_DQS#1 BD47 SB_DQ42 BK5 SM_RCOMP# BK14 SA_DQS#2 BC41 SB_DQ43 BL5 SM_RCOMP_VOH BK31 143 Ballout and Package Information Signal 15.2.9 Ball Signal Ball BA37 SB_DQ44 BK9 SM_RCOMP_VOL BL31 SA_DQS#4 BA16 SB_DQ45 BK10 SM_VREF AW4 SA_DQS#5 BH7 SB_DQ46 BJ8 SM_VREF AR49 No Connects Ball Signal Ball Signal Ball NC BJ51 NC A50 NC BL49 NC BK2 NC A49 NC BL3 NC E1 NC BK51 NC BL2 NC A5 NC BK50 NC BK1 NC C51 NC BL50 NC BJ1 NC B50 PCI Express Based Graphics Signal 144 Ball SA_DQS#3 Signal 15.2.10 Signal Ball Signal Ball Signal Ball PEG_COMPI N43 PEG_RX12 AH47 PEG_TX#4 R50 PEG_COMPO M43 PEG_RX13 AG49 PEG_TX#5 T42 PEG_RX#0 J51 PEG_RX14 AH45 PEG_TX#6 Y43 PEG_RX#1 L51 PEG_RX15 AG42 PEG_TX#7 W46 PEG_RX#10 AD44 PEG_RX2 M47 PEG_TX#8 W38 PEG_RX#11 AD40 PEG_RX3 U44 PEG_TX#9 AD39 PEG_RX#12 AG46 PEG_RX4 T49 PEG_TX0 M45 PEG_RX#13 AH49 PEG_RX5 T41 PEG_TX1 T38 PEG_RX#14 AG45 PEG_RX6 W45 PEG_TX10 AD47 PEG_RX#15 AG41 PEG_RX7 W41 PEG_TX11 AC50 PEG_RX#2 N47 PEG_RX8 AB50 PEG_TX12 AD43 PEG_RX#3 T45 PEG_RX9 Y48 PEG_TX13 AG39 PEG_RX#4 T50 PEG_TX#0 N45 PEG_TX14 AE50 PEG_RX#5 U40 PEG_TX#1 U39 PEG_TX15 AH43 PEG_RX#6 Y44 PEG_TX#10 AC46 PEG_TX2 T46 PEG_RX#7 Y40 PEG_TX#11 AC49 PEG_TX3 N50 PEG_RX#8 AB51 PEG_TX#12 AC42 PEG_TX4 R51 PEG_RX#9 W49 PEG_TX#13 AH39 PEG_TX5 U43 PEG_RX0 J50 PEG_TX#14 AE49 PEG_TX6 W42 Datasheet Ballout and Package Information Signal 15.2.11 Ball Signal Ball L50 PEG_TX#15 AH44 PEG_TX7 Y47 PEG_RX10 AC45 PEG_TX#2 U47 PEG_TX8 Y39 PEG_RX11 AC41 PEG_TX#3 N51 PEG_TX9 AC38 PLL Ball Signal Ball Signal Ball DPLL_REF_CLK B42 DPLL_REF_SSCLK# H47 PEG_CLK K44 DPLL_REF_CLK# C42 HPLL_CLK AM5 PEG_CLK# K45 DPLL_REF_SSCLK H48 HPLL_CLK# AM7 Power and Ground Signal Datasheet Signal PEG_RX1 Signal 15.2.12 Ball Ball Signal Ball Signal Ball VCC AT35 VCC_SM BK35 VSS AH9 VCC AT34 VCC_SM BK34 VSS AH7 VCC AK32 VCC_SM BK33 VSS AH3 VCC AJ31 VCC_SM BK32 VSS AG50 VCC AJ28 VCC_SM BJ34 VSS AG47 VCC AH32 VCC_SM BJ33 VSS AG43 VCC AH31 VCC_SM BJ32 VSS AG38 VCC AH29 VCC_SM BH35 VSS AG2 VCC AH28 VCC_SM BH34 VSS AF31 VCC AF32 VCC_SM BH32 VSS AF29 VCC AC32 VCC_SM BG35 VSS AF28 VCC AC31 VCC_SM BG33 VSS AF24 VCC R30 VCC_SM BG32 VSS AF23 VCC_AXD AU28 VCC_SM BF34 VSS AF20 VCC_AXD AU24 VCC_SM BF33 VSS AE14 VCC_AXD AT30 VCC_SM BE35 VSS AE10 VCC_AXD AT29 VCC_SM BE33 VSS AE6 VCC_AXD AT25 VCC_SM BE32 VSS AD50 VCC_AXD AT23 VCC_SM BD35 VSS AD49 VCC_AXD_NCTF AR29 VCC_SM BD32 VSS AD45 VCC_AXF B23 VCC_SM BC35 VSS AD41 VCC_AXF B21 VCC_SM BC33 VSS AD32 VCC_AXF A21 VCC_SM BC32 VSS AD29 VCC_AXG AN14 VCC_SM BB33 VSS AD26 145 Ballout and Package Information Signal 146 Ball Signal Ball Signal Ball VCC_AXG AJ20 VCC_SM BA35 VSS AD21 VCC_AXG AH26 VCC_SM BA33 VSS AD8 VCC_AXG AH24 VCC_SM BA32 VSS AD5 VCC_AXG AH23 VCC_SM AY35 VSS AD3 VCC_AXG AH21 VCC_SM AW35 VSS AD1 VCC_AXG AH20 VCC_SM AW33 VSS AC47 VCC_AXG AF26 VCC_SM AV33 VSS AC43 VCC_AXG AF21 VCC_SM AU35 VSS AC39 VCC_AXG AD31 VCC_SM AU33 VSS AC13 VCC_AXG AD28 VCC_SM AU32 VSS AC10 VCC_AXG AD24 VCC_SM AU30 VSS AC3 VCC_AXG AD23 VCC_SM_CK BK24 VSS AB32 VCC_AXG AD20 VCC_SM_CK BK23 VSS AB31 VCC_AXG AC29 VCC_SM_CK BJ24 VSS AB28 VCC_AXG AC28 VCC_SM_CK BJ23 VSS AB26 VCC_AXG AC26 VCC_SM_LF1 AW45 VSS AB23 VCC_AXG AC24 VCC_SM_LF2 BC39 VSS AB20 VCC_AXG AC23 VCC_SM_LF3 BE39 VSS AA32 VCC_AXG AC21 VCC_SM_LF4 BD17 VSS AA29 VCC_AXG AC20 VCC_SM_LF5 BD4 VSS AA24 VCC_AXG AB29 VCC_SM_LF6 AW8 VSS AA21 VCC_AXG AB24 VCC_SM_LF7 AT6 VSS Y50 VCC_AXG AB21 VCC_SYNC J32 VSS Y49 VCC_AXG AA31 VCC_TX_LVDS A43 VSS Y45 VCC_AXG AA28 VCCA_CRT_DAC B33 VSS Y41 VCC_AXG AA26 VCCA_CRT_DAC A33 VSS Y13 VCC_AXG AA23 VCCA_DAC_BG A30 VSS Y11 VCC_AXG AA20 VCCA_DPLLA B49 VSS Y5 VCC_AXG Y12 VCCA_DPLLB H49 VSS Y2 VCC_AXG W14 VCCA_HPLL AL2 VSS W47 VCC_AXG W13 VCCA_LVDS A41 VSS W43 VCC_AXG T14 VCCA_MPLL AM2 VSS W39 VCC_AXG R20 VCCA_PEG_BG K50 VSS W11 VCC_AXG_NCTF AR26 VCCA_PEG_PLL U51 VSS W7 VCC_AXG_NCTF AR24 VCCA_SM AW18 VSS W5 VCC_AXG_NCTF AR23 VCCA_SM AV19 VSS V3 VCC_AXG_NCTF AR21 VCCA_SM AU19 VSS V2 VCC_AXG_NCTF AR20 VCCA_SM AU18 VSS U50 VCC_AXG_NCTF AP24 VCCA_SM AU17 VSS U45 Datasheet Ballout and Package Information Signal Datasheet Ball Signal Ball Signal Ball VCC_AXG_NCTF AP23 VCCA_SM AT22 VSS U41 VCC_AXG_NCTF AP21 VCCA_SM AT21 VSS T47 VCC_AXG_NCTF AP20 VCCA_SM AT19 VSS T43 VCC_AXG_NCTF AP19 VCCA_SM AT18 VSS T39 VCC_AXG_NCTF AP17 VCCA_SM AT17 VSS R49 VCC_AXG_NCTF AP16 VCCA_SM_CK BC29 VSS P50 VCC_AXG_NCTF AP15 VCCA_SM_CK BB29 VSS P29 VCC_AXG_NCTF AM23 VCCA_SM_NCTF AR17 VSS P23 VCC_AXG_NCTF AM21 VCCA_SM_NCTF AR16 VSS P19 VCC_AXG_NCTF AM20 VCCA_TVA_DAC C25 VSS P3 VCC_AXG_NCTF AM19 VCCA_TVA_DAC B25 VSS P2 VCC_AXG_NCTF AM16 VCCA_TVB_DAC C27 VSS N49 VCC_AXG_NCTF AM15 VCCA_TVB_DAC B27 VSS N44 VCC_AXG_NCTF AL23 VCCA_TVC_DAC B28 VSS N39 VCC_AXG_NCTF AL21 VCCA_TVC_DAC A28 VSS N36 VCC_AXG_NCTF AL20 VCCD_CRT M32 VSS N32 VCC_AXG_NCTF AL19 VCCD_HPLL AN2 VSS N29 VCC_AXG_NCTF AL17 VCCD_LVDS J41 VSS N17 VCC_AXG_NCTF AL16 VCCD_LVDS H42 VSS N14 VCC_AXG_NCTF AK19 VCCD_PEG_PLL U48 VSS N11 VCC_AXG_NCTF AK16 VCCD_TVDAC L29 VSS N7 VCC_AXG_NCTF AJ19 VCCD_QDAC N28 VSS M50 VCC_AXG_NCTF AJ17 VSS T33 VSS M49 VCC_AXG_NCTF AJ16 VSS R28 VSS M46 VCC_AXG_NCTF AH19 VSS T31 VSS M42 VCC_AXG_NCTF AH17 VSS T29 VSS M28 VCC_AXG_NCTF AH16 VSS BL47 VSS M9 VCC_AXG_NCTF AH15 VSS BL37 VSS M5 VCC_AXG_NCTF AF19 VSS BL22 VSS L49 VCC_AXG_NCTF AF16 VSS BL19 VSS L33 VCC_AXG_NCTF AD17 VSS BL13 VSS L28 VCC_AXG_NCTF AD16 VSS BL11 VSS L24 VCC_AXG_NCTF AD15 VSS BK44 VSS L20 VCC_AXG_NCTF AC19 VSS BK40 VSS L17 VCC_AXG_NCTF AC17 VSS BK36 VSS L3 VCC_AXG_NCTF AC16 VSS BK29 VSS L1 VCC_AXG_NCTF AB19 VSS BK25 VSS K47 VCC_AXG_NCTF AB16 VSS BK17 VSS K12 VCC_AXG_NCTF AA17 VSS BK15 VSS K8 147 Ballout and Package Information Signal 148 Ball Signal Ball Signal Ball VCC_AXG_NCTF AA16 VSS BK8 VSS J39 VCC_AXG_NCTF Y31 VSS BK6 VSS J35 VCC_AXG_NCTF Y29 VSS BJ46 VSS J33 VCC_AXG_NCTF Y28 VSS BJ42 VSS J28 VCC_AXG_NCTF Y26 VSS BJ38 VSS J24 VCC_AXG_NCTF Y24 VSS BJ13 VSS J16 VCC_AXG_NCTF Y23 VSS BJ11 VSS J11 VCC_AXG_NCTF Y21 VSS BJ4 VSS J2 VCC_AXG_NCTF Y20 VSS BH46 VSS H50 VCC_AXG_NCTF Y19 VSS BH44 VSS H45 VCC_AXG_NCTF Y17 VSS BH30 VSS H28 VCC_AXG_NCTF Y16 VSS BH17 VSS H24 VCC_AXG_NCTF Y15 VSS BH8 VSS H4 VCC_AXG_NCTF V29 VSS BG51 VSS G48 VCC_AXG_NCTF V28 VSS BG48 VSS G45 VCC_AXG_NCTF V26 VSS BG39 VSS G42 VCC_AXG_NCTF V24 VSS BG29 VSS G33 VCC_AXG_NCTF V23 VSS BG24 VSS G29 VCC_AXG_NCTF V21 VSS BG19 VSS G28 VCC_AXG_NCTF V20 VSS BG5 VSS G24 VCC_AXG_NCTF V19 VSS BG2 VSS G19 VCC_AXG_NCTF V17 VSS BF36 VSS G16 VCC_AXG_NCTF V16 VSS BF16 VSS G13 VCC_AXG_NCTF U26 VSS BF12 VSS G8 VCC_AXG_NCTF U23 VSS BE51 VSS G1 VCC_AXG_NCTF U21 VSS BE42 VSS F50 VCC_AXG_NCTF U20 VSS BE30 VSS F40 VCC_AXG_NCTF U19 VSS BE23 VSS F36 VCC_AXG_NCTF U17 VSS BE19 VSS F19 VCC_AXG_NCTF U16 VSS BE8 VSS F4 VCC_AXG_NCTF U15 VSS BE1 VSS E47 VCC_AXG_NCTF T25 VSS BD48 VSS E32 VCC_AXG_NCTF T23 VSS BD45 VSS E28 VCC_AXG_NCTF T22 VSS BD28 VSS E24 VCC_AXG_NCTF T21 VSS BD13 VSS E16 VCC_AXG_NCTF T19 VSS BD5 VSS E10 VCC_AXG_NCTF T18 VSS BD2 VSS D49 VCC_AXG_NCTF T17 VSS BC51 VSS D45 VCC_AXM AT33 VSS BC40 VSS D39 Datasheet Ballout and Package Information Signal Datasheet Ball Signal Ball Signal Ball VCC_AXM AT31 VSS BC36 VSS D32 VCC_AXM AK29 VSS BC25 VSS D24 VCC_AXM AK24 VSS BC24 VSS D13 VCC_AXM AK23 VSS BC16 VSS D3 VCC_AXM AJ26 VSS BB49 VSS C50 VCC_AXM AJ23 VSS BB44 VSS C46 VCC_AXM_NCTF AR33 VSS BB40 VSS C41 VCC_AXM_NCTF AR32 VSS BB25 VSS C36 VCC_AXM_NCTF AR31 VSS BB12 VSS C33 VCC_AXM_NCTF AP33 VSS BB8 VSS C29 VCC_AXM_NCTF AP32 VSS BA24 VSS C28 VCC_AXM_NCTF AP31 VSS BA18 VSS C19 VCC_AXM_NCTF AP29 VSS BA17 VSS C16 VCC_AXM_NCTF AM33 VSS BA2 VSS C12 VCC_AXM_NCTF AM32 VSS BA1 VSS C7 VCC_AXM_NCTF AM31 VSS AY50 VSS B46 VCC_AXM_NCTF AM29 VSS AY47 VSS B43 VCC_AXM_NCTF AM28 VSS AY45 VSS B38 VCC_AXM_NCTF AM26 VSS AY43 VSS B35 VCC_AXM_NCTF AL32 VSS AY42 VSS B30 VCC_AXM_NCTF AL31 VSS AY37 VSS B29 VCC_AXM_NCTF AL29 VSS AY24 VSS B24 VCC_AXM_NCTF AL28 VSS AY10 VSS B20 VCC_AXM_NCTF AL26 VSS AW32 VSS B10 VCC_AXM_NCTF AL24 VSS AW29 VSS B8 VCC_DMI AJ50 VSS AW24 VSS B5 VCC_HV C40 VSS AW16 VSS A24 VCC_HV B40 VSS AW12 VSS A17 VCC_NCTF AR36 VSS AW7 VSS A15 VCC_NCTF AR35 VSS AW5 VSS A13 VCC_NCTF AP36 VSS AW1 VSS_NCTF AR28 VCC_NCTF AP35 VSS AV48 VSS_NCTF AR19 VCC_NCTF AM35 VSS AV39 VSS_NCTF AR15 VCC_NCTF AL35 VSS AV25 VSS_NCTF AP28 VCC_NCTF AL33 VSS AU51 VSS_NCTF AP26 VCC_NCTF AK37 VSS AU49 VSS_NCTF AM24 VCC_NCTF AK36 VSS AU36 VSS_NCTF AM17 VCC_NCTF AK35 VSS AU29 VSS_NCTF AK17 VCC_NCTF AK33 VSS AU23 VSS_NCTF AF35 149 Ballout and Package Information Signal 150 Ball Signal Ball Signal Ball VCC_NCTF AJ36 VSS AU3 VSS_NCTF AF17 VCC_NCTF AJ35 VSS AU1 VSS_NCTF AD37 VCC_NCTF AJ33 VSS AT49 VSS_NCTF AD19 VCC_NCTF AH37 VSS AT41 VSS_NCTF AB35 VCC_NCTF AH36 VSS AT27 VSS_NCTF AB17 VCC_NCTF AH35 VSS AT14 VSS_NCTF AA19 VCC_NCTF AH33 VSS AT10 VSS_NCTF V35 VCC_NCTF AF36 VSS AR47 VSS_NCTF V31 VCC_NCTF AF33 VSS AR44 VSS_NCTF U28 VCC_NCTF AD36 VSS AR39 VSS_NCTF U24 VCC_NCTF AD35 VSS AR11 VSS_NCTF T37 VCC_NCTF AD33 VSS AR7 VSS_NCTF T27 VCC_NCTF AC36 VSS AR2 VSS_SCB1 A3 VCC_NCTF AC35 VSS AP50 VSS_SCB2 B2 VCC_NCTF AC33 VSS AP48 VSS_SCB3 C1 VCC_NCTF AB37 VSS AP4 VSS_SCB4 BL1 VCC_NCTF AB36 VSS AN43 VSS_SCB5 BL51 VCC_NCTF AB33 VSS AN39 VSS_SCB6 A51 VCC_NCTF AA36 VSS AN38 VSSA_DAC_BG B32 VCC_NCTF AA35 VSS AN7 VSSA_LVDS B41 VCC_NCTF AA33 VSS AN5 VSSA_PEG_BG K49 VCC_NCTF Y37 VSS AN1 VTT U13 VCC_NCTF Y36 VSS AM45 VTT U12 VCC_NCTF Y35 VSS AM41 VTT U11 VCC_NCTF Y33 VSS AM13 VTT U9 VCC_NCTF Y32 VSS AM11 VTT U8 VCC_NCTF V37 VSS AM4 VTT U7 VCC_NCTF V36 VSS AM3 VTT U5 VCC_NCTF V33 VSS AL1 VTT U3 VCC_NCTF V32 VSS AK51 VTT U2 VCC_NCTF U36 VSS AK31 VTT U1 VCC_NCTF U35 VSS AK28 VTT T13 VCC_NCTF U33 VSS AK26 VTT T11 VCC_NCTF U32 VSS AK21 VTT T10 VCC_NCTF U31 VSS AK20 VTT T9 VCC_NCTF U29 VSS AJ49 VTT T7 VCC_NCTF T35 VSS AJ45 VTT T6 VCC_NCTF T34 VSS AJ43 VTT T5 VCC_NCTF T30 VSS AJ32 VTT T3 Datasheet Ballout and Package Information Signal 15.2.13 15.2.14 Signal Ball Signal Ball VCC_PEG AD51 VSS AJ29 VTT T2 VCC_PEG W51 VSS AJ24 VTT R3 VCC_PEG W50 VSS AJ21 VTT R2 VCC_PEG V50 VSS AJ13 VTT R1 VCC_PEG V49 VSS AJ11 VTTLF1 A7 VCC_RXR_DMI AH51 VSS AH41 VTTLF2 F2 VCC_RXR_DMI AH50 VSS AH40 VTTLF3 AH1 VCC_SM BL33 Reserved and Test Signal Ball Signal Ball Signal Ball RSVD A35 RSVD BF19 RSVD AM12 RSVD B37 RSVD BH20 RSVD AN13 RSVD B36 RSVD BK18 RSVD AR37 RSVD B34 RSVD BJ18 RSVD AM36 RSVD C34 RSVD AW20 RSVD AL36 RSVD BF23 RSVD BK20 RSVD AM37 RSVD BG23 RSVD P36 RSVD D20 RSVD BJ20 RSVD P37 RSVD B51 RSVD BK22 RSVD R35 TEST1 A37 TEST2 R32 RSVD BC23 RSVD N35 RSVD BD24 RSVD J12 RSVD BH39 RSVD H10 RSVD AR12 RSVD AR13 Strappings Signal CFG0 Datasheet Ball Ball P27 Signal CFG8 Ball J20 Signal CFG15 Ball K23 CFG1 N27 CFG9 C20 CFG16 M20 CFG3 C21 CFG10 R24 CFG17 M24 CFG4 C23 CFG11 L23 CFG18 L32 CFG5 F23 CFG12 J23 CFG19 N33 CFG6 N23 CFG13 E23 CFG2 N24 CFG7 G23 CFG14 E20 CFG20 L35 151 Ballout and Package Information 15.2.15 Reset and Miscellaneous Signal 15.3 Signal Ball Signal Ball CLKREQ# G39 GFX_VID3 B39 PM_EXT_TS#0 L36 DPRSLPVR G36 GFX_VR_EN E36 PM_EXT_TS#1 J36 GFX_VID0 E35 ICH_SYNC# G40 PWROK AW49 GFX_VID1 A39 PMSYNC# (PM_BM_BUSY#) G41 RSTIN# AV20 GFX_VID2 C38 PM_DPRSTP# L39 Ball List (Listed by Ball) Ball 152 Ball Signal Ball Signal Ball Signal A11 H_REQ#2 V16 VCC_AXG_NCTF AR37 RSVD A13 VSS V17 VCC_AXG_NCTF AR39 VSS A15 VSS V19 VCC_AXG_NCTF AR40 SA_DQ24 A17 VSS V2 VSS AR41 SA_DQ4 A19 H_A#33 V20 VCC_AXG_NCTF AR43 SA_DQ0 A21 VCC_AXF V21 VCC_AXG_NCTF AR44 VSS A24 VSS V23 VCC_AXG_NCTF AR45 SA_DQ5 A28 VCCA_TVC_DAC V24 VCC_AXG_NCTF AR47 VSS A3 VSS_SCB1 V26 VCC_AXG_NCTF AR49 SM_VREF A30 VCCA_DAC_BG V28 VCC_AXG_NCTF AR5 SA_DQ54 A33 VCCA_CRT_DAC V29 VCC_AXG_NCTF AR50 SB_DM0 A35 RSVD V3 VSS AR51 SB_DQ1 A37 TEST1 V31 VSS_NCTF AR7 VSS A39 GFX_VID1 V32 VCC_NCTF AR8 SA_DQ55 A41 VCCA_LVDS V33 VCC_NCTF AR9 SA_DQ56 A43 VCC_TX_LVDS V35 VSS_NCTF AT10 VSS A45 LVDSB_DATA2 V36 VCC_NCTF AT11 SA_DQ37 A47 LVDSB_DATA1 V37 VCC_NCTF AT13 SA_DQ33 A49 NC V4 H_D#19 AT14 VSS A5 NC V49 VCC_PEG AT17 VCCA_SM A50 NC V50 VCC_PEG AT18 VCCA_SM A51 VSS_SCB6 W1 H_SCOMP AT19 VCCA_SM A7 VTTLF1 W10 H_D#17 AT2 SB_DQ63 A9 H_DVREF W11 VSS AT21 VCCA_SM B10 VSS W13 VCC_AXG AT22 VCCA_SM Datasheet Ballout and Package Information Ball Datasheet Signal Ball Signal Ball Signal B11 H_A#4 W14 VCC_AXG AT23 VCC_AXD B12 H_REQ#4 W2 H_SCOMP# AT25 VCC_AXD B13 H_A#13 W3 H_D#30 AT27 VSS B14 H_A#16 W38 PEG_TX#8 AT29 VCC_AXD B15 H_A#30 W39 VSS AT3 SB_DQ59 B16 H_A#20 W41 PEG_RX7 AT30 VCC_AXD B17 H_A#29 W42 PEG_TX6 AT31 VCC_AXM B18 H_A#27 W43 VSS AT33 VCC_AXM B19 H_A#34 W45 PEG_RX6 AT34 VCC B2 VSS_SCB2 W46 PEG_TX#7 AT35 VCC B20 VSS W47 VSS AT38 SA_DQ31 B21 VCC_AXF W49 PEG_RX#9 AT39 SA_DQ26 B23 VCC_AXF W5 VSS AT41 VSS B24 VSS W50 VCC_PEG AT42 SA_DQ6 B25 VCCA_TVA_DAC W51 VCC_PEG AT43 CL_PWROK B27 VCCA_TVB_DAC W6 H_D#24 AT45 SA_DM0 B28 VCCA_TVC_DAC W7 VSS AT46 SA_DQS0 B29 VSS W9 H_D#25 AT47 SA_DQS#0 B3 H_SWING Y11 VSS AT49 VSS B30 VSS Y12 VCC_AXG AT5 SA_DQ50 B32 VSSA_DAC_BG Y13 VSS AT50 SB_DQS0 B33 VCCA_CRT_DAC Y15 VCC_AXG_NCTF AT6 VCC_SM_LF7 B34 RSVD Y16 VCC_AXG_NCTF AT7 SA_DQ51 B35 VSS Y17 VCC_AXG_NCTF AT9 SA_DQ60 B36 RSVD Y19 VCC_AXG_NCTF AU1 VSS B37 RSVD Y2 VSS AU15 SA_DQ36 B38 VSS Y20 VCC_AXG_NCTF AU17 VCCA_SM B39 GFX_VID3 Y21 VCC_AXG_NCTF AU18 VCCA_SM B40 VCC_HV Y23 VCC_AXG_NCTF AU19 VCCA_SM B41 VSSA_LVDS Y24 VCC_AXG_NCTF AU2 SB_DQ62 B42 DPLL_REF_CLK Y26 VCC_AXG_NCTF AU23 VSS B43 VSS Y28 VCC_AXG_NCTF AU24 VCC_AXD B44 LVDSB_DATA#3 Y29 VCC_AXG_NCTF AU28 VCC_AXD B45 LVDSB_DATA#2 Y3 H_D#43 AU29 VSS B46 VSS Y31 VCC_AXG_NCTF AU3 VSS B47 LVDSB_DATA#1 Y32 VCC_NCTF AU30 VCC_SM B49 VCCA_DPLLA Y33 VCC_NCTF AU32 VCC_SM B5 VSS Y35 VCC_NCTF AU33 VCC_SM B50 NC Y36 VCC_NCTF AU35 VCC_SM 153 Ballout and Package Information Ball 154 Signal Ball Signal Ball Signal B51 RSVD Y37 VCC_NCTF AU36 VSS B6 H_CPURST# Y39 PEG_TX8 AU49 VSS B7 H_TRDY# Y40 PEG_RX#7 AU50 SB_DQS#0 B8 VSS Y41 VSS AU51 VSS B9 H_AVREF Y43 PEG_TX#6 AV11 SA_DQ35 C1 VSS_SCB3 Y44 PEG_RX#6 AV13 SA_DQ32 C10 H_DBSY# Y45 VSS AV16 SB_RAS# C11 H_A#5 Y47 PEG_TX7 AV19 VCCA_SM C12 VSS Y48 PEG_RX9 AV2 SB_DQS7 C14 H_A#11 Y49 VSS AV20 RSTIN# C15 H_A#7 Y5 VSS AV23 SM_CK4 C16 VSS Y50 VSS AV25 VSS C18 H_A#32 Y7 H_D#27 AV29 SM_CK0 C19 VSS Y8 H_D#18 AV3 SB_DQS#7 C2 H_RCOMP Y9 H_D#28 AV33 VCC_SM C20 CFG9 AA16 VCC_AXG_NCTF AV38 SA_DQ30 C21 CFG3 AA17 VCC_AXG_NCTF AV39 VSS C23 CFG4 AA19 VSS_NCTF AV48 VSS C25 VCCA_TVA_DAC AA20 VCC_AXG AV49 SB_DQ7 C27 VCCA_TVB_DAC AA21 VSS AV50 SB_DQ6 C28 VSS AA23 VCC_AXG AW1 VSS C29 VSS AA24 VSS AW11 SA_DQ34 C32 CRT_TVO_IREF AA26 VCC_AXG AW12 VSS C33 VSS AA28 VCC_AXG AW13 SA_DM4 C34 RSVD AA29 VSS AW16 VSS C36 VSS AA31 VCC_AXG AW17 SB_MA3 C37 L_DDC_CLK AA32 VSS AW18 VCCA_SM C38 GFX_VID2 AA33 VCC_NCTF AW2 SB_DM7 C40 VCC_HV AA35 VCC_NCTF AW20 RSVD C41 VSS AA36 VCC_NCTF AW23 SM_CK#4 C42 DPLL_REF_CLK# AB1 H_D#42 AW24 VSS C44 LVDSB_DATA3 AB16 VCC_AXG_NCTF AW25 SM_CK#3 C45 LVDSA_CLK AB17 VSS_NCTF AW29 VSS C46 VSS AB19 VCC_AXG_NCTF AW30 SM_CK#0 C48 LVDSA_DATA#3 AB2 H_D#40 AW32 VSS C50 VSS AB20 VSS AW33 VCC_SM C51 NC AB21 VCC_AXG AW35 VCC_SM C6 H_HITM# AB23 VSS AW36 SA_DQ27 C7 VSS AB24 VCC_AXG AW38 SA_DM3 Datasheet Ballout and Package Information Ball Datasheet Signal Ball Signal Ball Signal C8 H_BNR# AB26 VSS AW4 SM_VREF D13 VSS AB28 VSS AW40 SA_DQ25 D17 H_A#23 AB29 VCC_AXG AW41 SA_DQ28 D20 RSVD AB31 VSS AW43 SA_DQ16 D24 VSS AB32 VSS AW44 SA_DQ1 D3 VSS AB33 VCC_NCTF AW45 VCC_SM_LF1 D32 VSS AB35 VSS_NCTF AW47 SA_DQ7 D35 L_DDC_DATA AB36 VCC_NCTF AW49 PWROK D39 VSS AB37 VCC_NCTF AW5 VSS D44 LVDSB_CLK# AB50 PEG_RX8 AW50 SB_DQ2 D45 VSS AB51 PEG_RX#8 AW51 SB_DQ3 D46 LVDSA_CLK# AC10 VSS AW7 VSS D47 LVDSA_DATA3 AC11 H_D#39 AW8 VCC_SM_LF6 D49 VSS AC13 VSS AW9 SA_DQ45 D6 H_DEFER# AC14 H_D#37 AY10 VSS D7 H_RS#1 AC16 VCC_AXG_NCTF AY17 SB_BS0 D8 H_RS#2 AC17 VCC_AXG_NCTF AY18 SB_RCVEN# E1 NC AC19 VCC_AXG_NCTF AY2 SB_DQ60 E10 VSS AC2 H_DSTBP#2 AY20 SA_RCVEN# E12 H_RS#0 AC20 VCC_AXG AY24 VSS E13 H_REQ#1 AC21 VCC_AXG AY28 SB_MA8 E16 VSS AC23 VCC_AXG AY3 SB_DQ61 E17 H_A#31 AC24 VCC_AXG AY32 SM_CKE1 E19 H_A#28 AC26 VCC_AXG AY35 VCC_SM E2 H_D#0 AC28 VCC_AXG AY37 VSS E20 CFG14 AC29 VCC_AXG AY41 SA_DQ29 E23 CFG13 AC3 VSS AY42 VSS E24 VSS AC31 VCC AY43 VSS E27 TVA_DAC AC32 VCC AY45 VSS E28 VSS AC33 VCC_NCTF AY46 SA_DQ3 E29 CRT_RED# AC35 VCC_NCTF AY47 VSS E32 VSS AC36 VCC_NCTF AY49 SB_DQ13 E33 CRT_VSYNC AC38 PEG_TX9 AY5 SA_DM6 E35 GFX_VID0 AC39 VSS AY50 VSS E36 GFX_VR_EN AC41 PEG_RX11 AY6 SA_DQ52 E39 L_CTRL_CLK AC42 PEG_TX#12 AY7 SA_DQ49 E4 H_HIT# AC43 VSS AY9 SA_DQ43 E40 L_CTRL_DATA AC45 PEG_RX10 BA1 VSS E42 LVDSB_CLK AC46 PEG_TX#10 BA11 SA_DQ39 155 Ballout and Package Information Ball 156 Signal Ball Signal Ball Signal E44 LVDSB_DATA0 AC47 VSS BA13 SA_DQ38 E47 VSS AC49 PEG_TX#11 BA16 SA_DQS#4 E5 H_CPUSLP# AC5 H_D#46 BA17 VSS E50 LVDSA_DATA1 AC50 PEG_TX11 BA18 VSS E51 LVDSA_DATA#1 AC6 H_D#44 BA19 SA_WE# E8 H_BPRI# AC7 H_D#36 BA2 VSS F12 H_BREQ# AC9 H_D#35 BA23 SM_CK#1 F16 H_A#8 AD1 VSS BA24 VSS F19 VSS AD11 H_D#38 BA25 SM_CK3 F2 VTTLF2 AD12 H_D#32 BA28 SA_MA9 F23 CFG5 AD13 H_DINV#2 BA29 SB_MA6 F27 TVA_RTN AD15 VCC_AXG_NCTF BA3 SB_DQ56 F29 CRT_RED AD16 VCC_AXG_NCTF BA32 VCC_SM F3 H_D#7 AD17 VCC_AXG_NCTF BA33 VCC_SM F33 CRT_HSYNC AD19 VSS_NCTF BA35 VCC_SM F36 VSS AD2 H_DSTBN#2 BA37 SA_DQS#3 F4 VSS AD20 VCC_AXG BA39 SB_MA12 F40 VSS AD21 VSS BA45 SA_DQ2 F48 LVDSA_DATA2 AD23 VCC_AXG BA49 SB_DQ10 F49 LVDSA_DATA#2 AD24 VCC_AXG BA50 SB_DQ8 F50 VSS AD26 VSS BA51 SB_DQ12 G1 VSS AD28 VCC_AXG BB12 VSS G10 H_LOCK# AD29 VSS BB16 SA_DQS4 G12 H_ADS# AD3 VSS BB19 SA_BS0 G13 VSS AD31 VCC_AXG BB2 SA_DQS6 G16 VSS AD32 VSS BB23 SM_CK1 G17 H_A#10 AD33 VCC_NCTF BB25 VSS G19 VSS AD35 VCC_NCTF BB29 VCCA_SM_CK G2 H_D#1 AD36 VCC_NCTF BB3 SB_DQ57 G20 H_ADSTB#1 AD37 VSS_NCTF BB33 VCC_SM G23 CFG7 AD39 PEG_TX#9 BB40 VSS G24 VSS AD40 PEG_RX#11 BB43 SA_DQS2 G27 TVB_DAC AD41 VSS BB44 VSS G28 VSS AD43 PEG_TX12 BB45 SA_DQ8 G29 VSS AD44 PEG_RX#10 BB47 SA_DQ12 G32 CRT_BLUE# AD45 VSS BB49 VSS G33 VSS AD47 PEG_TX10 BB5 SA_DQ48 G35 CRT_DDC_DATA AD49 VSS BB50 SB_DQ9 G36 DPRSLPVR AD5 VSS BB7 SA_DQ53 Datasheet Ballout and Package Information Ball Datasheet Signal Ball Signal Ball Signal G39 CLKREQ# AD50 VSS BB8 VSS G4 H_D#6 AD51 VCC_PEG BB9 SA_DQ47 G40 ICH_SYNC# AD7 H_D#41 BC1 SA_DQS#6 G41 PMSYNC# (PM_BM_BUSY#) AD8 VSS BC11 SB_DQ35 G42 VSS AD9 H_D#34 BC12 SB_DQ38 G44 LVDSB_DATA#0 AE10 VSS BC13 SB_DQ36 G45 VSS AE11 H_D#52 BC16 VSS G48 VSS AE13 H_DINV#3 BC17 SB_WE# G50 LVDSA_DATA0 AE14 VSS BC18 SB_MA0 G51 LVDSA_DATA#0 AE2 H_D#45 BC19 SA_MA10 G7 H_D#2 AE3 H_D#33 BC2 SB_DQ51 G8 VSS AE49 PEG_TX#14 BC23 RSVD H10 RSVD AE5 H_D#60 BC24 VSS H13 H_REQ#3 AE50 PEG_TX14 BC25 VSS H17 H_ADSTB#0 AE6 VSS BC28 SB_MA7 H2 H_D#9 AE7 H_D#57 BC29 VCCA_SM_CK H20 H_A#21 AE9 H_D#51 BC32 VCC_SM H24 VSS AF16 VCC_AXG_NCTF BC33 VCC_SM H28 VSS AF17 VSS_NCTF BC35 VCC_SM H3 H_D#5 AF19 VCC_AXG_NCTF BC36 VSS H32 CRT_BLUE AF20 VSS BC37 SA_DQS3 H35 SDVO_CTRL_CLK AF21 VCC_AXG BC39 VCC_SM_LF2 H39 L_BKLT_EN AF23 VSS BC40 VSS H4 VSS AF24 VSS BC41 SA_DQS#2 H42 VCCD_LVDS AF26 VCC_AXG BC50 SB_DQS#1 H45 VSS AF28 VSS BC51 VSS H47 DPLL_REF_SSCLK # AF29 VSS BD10 SA_DQ41 H48 DPLL_REF_SSCLK AF31 VSS BD13 VSS H49 VCCA_DPLLB AF32 VCC BD17 VCC_SM_LF4 H5 H_D#13 AF33 VCC_NCTF BD2 VSS H50 VSS AF35 VSS_NCTF BD20 SA_MA1 H7 H_D#4 AF36 VCC_NCTF BD24 RSVD H8 H_DPWR# AG2 VSS BD28 VSS J1 H_D#21 AG3 H_D#47 BD3 SB_DQ54 J11 VSS AG38 VSS BD32 VCC_SM J12 RSVD AG39 PEG_TX13 BD35 VCC_SM J13 H_A#3 AG41 PEG_RX#15 BD37 SB_MA9 157 Ballout and Package Information Ball 158 Signal Ball Signal Ball Signal J16 VSS AG42 PEG_RX15 BD39 SM_CKE3 J17 H_A#15 AG43 VSS BD4 VCC_SM_LF5 J19 H_A#26 AG45 PEG_RX#14 BD42 SA_DM2 J2 VSS AG46 PEG_RX#12 BD44 SA_DM1 J20 CFG8 AG47 VSS BD45 VSS J23 CFG12 AG49 PEG_RX13 BD47 SA_DQS#1 J24 VSS AG50 VSS BD48 VSS J27 TVB_RTN AH1 VTTLF3 BD49 SB_DM1 J28 VSS AH11 H_DSTBN#3 BD5 VSS J29 CRT_GREEN# AH12 H_D#53 BD50 SB_DQS1 J32 VCC_SYNC AH13 H_D#63 BD7 SA_DQ46 J33 VSS AH15 VCC_AXG_NCTF BD8 SA_DQ42 J35 VSS AH16 VCC_AXG_NCTF BE1 VSS J36 PM_EXT_TS#1 AH17 VCC_AXG_NCTF BE10 SA_DQ40 J39 VSS AH19 VCC_AXG_NCTF BE11 SB_DQ33 J40 L_BKLT_CTRL AH2 H_D#62 BE12 SB_DQ37 J41 VCCD_LVDS AH20 VCC_AXG BE13 SM_CS#3 J50 PEG_RX0 AH21 VCC_AXG BE16 SM_ODT3 J51 PEG_RX#0 AH23 VCC_AXG BE17 SB_CAS# K12 VSS AH24 VCC_AXG BE18 SA_RAS# K16 H_A#12 AH26 VCC_AXG BE19 VSS K19 H_A#17 AH28 VCC BE2 SB_DQS6 K2 H_DSTBP#1 AH29 VCC BE23 VSS K23 CFG15 AH3 VSS BE24 SB_MA_14 K27 TVC_DAC AH31 VCC BE25 SB_MA5 K29 CRT_GREEN AH32 VCC BE28 SA_MA11 K3 H_DSTBN#1 AH33 VCC_NCTF BE29 SM_CKE0 K33 CRT_DDC_CLK AH35 VCC_NCTF BE30 VSS K36 SDVO_CTRL_DATA AH36 VCC_NCTF BE32 VCC_SM K40 L_VDD_EN AH37 VCC_NCTF BE33 VCC_SM K44 PEG_CLK AH39 PEG_TX#13 BE35 VCC_SM K45 PEG_CLK# AH40 VSS BE37 SB_MA11 K47 VSS AH41 VSS BE39 VCC_SM_LF3 K49 VSSA_PEG_BG AH43 PEG_TX15 BE4 SB_DQ53 K5 H_DINV#0 AH44 PEG_TX#15 BE40 SA_DQ19 K50 VCCA_PEG_BG AH45 PEG_RX14 BE42 VSS K7 H_DRDY# AH47 PEG_RX12 BE44 SA_DQ17 K8 VSS AH49 PEG_RX#13 BE45 SA_DQ15 K9 H_D#15 AH5 H_D#55 BE48 SA_DQS1 Datasheet Ballout and Package Information Ball Datasheet Signal Ball Signal Ball Signal L1 VSS AH50 VCC_RXR_DMI BE50 SB_DQ11 L13 H_A#9 AH51 VCC_RXR_DMI BE51 VSS L16 H_A#14 AH7 VSS BE8 VSS L17 VSS AH8 H_D#49 BF12 VSS L19 H_A#22 AH9 VSS BF16 VSS L2 H_DINV#1 AJ10 H_DSTBP#3 BF19 RSVD L20 VSS AJ11 VSS BF2 SB_DQS#6 L23 CFG11 AJ13 VSS BF23 RSVD L24 VSS AJ14 H_D#50 BF25 SB_MA4 L27 TVC_RTN AJ16 VCC_AXG_NCTF BF29 SA_BS2 L28 VSS AJ17 VCC_AXG_NCTF BF3 SB_DM6 L29 VCCD_TVDAC AJ19 VCC_AXG_NCTF BF33 VCC_SM L3 VSS AJ2 H_D#59 BF34 VCC_SM L32 CFG18 AJ20 VCC_AXG BF36 VSS L33 VSS AJ21 VSS BF4 SB_DQ48 L35 CFG20 AJ23 VCC_AXM BF40 SA_DQ23 L36 PM_EXT_TS#0 AJ24 VSS BF44 SA_DQ20 L39 PM_DPRSTP# AJ26 VCC_AXM BF48 SA_DQ9 L41 LVDS_IBG AJ28 VCC BF49 SB_DQ15 L43 LVDS_VBG AJ29 VSS BF50 SB_DQ14 L49 VSS AJ3 H_D#61 BG1 SB_DQ50 L50 PEG_RX1 AJ31 VCC BG10 SA_DQ44 L51 PEG_RX#1 AJ32 VSS BG12 SB_DQ39 L7 H_DSTBP#0 AJ33 VCC_NCTF BG13 SB_MA13 M10 H_D#10 AJ35 VCC_NCTF BG16 SM_CS#2 M11 H_A#6 AJ36 VCC_NCTF BG17 SB_MA10 M14 H_REQ#0 AJ38 DMI_RXN1 BG18 SB_BS1 M17 H_A#24 AJ39 DMI_RXP1 BG19 VSS M2 H_D#16 AJ41 DMI_TXN1 BG2 VSS M20 CFG16 AJ42 DMI_TXP1 BG20 SM_CS#0 M24 CFG17 AJ43 VSS BG23 RSVD M28 VSS AJ45 VSS BG24 VSS M3 H_D#20 AJ46 DMI_TXN0 BG25 SB_MA2 M32 VCCD_CRT AJ47 DMI_TXP0 BG28 SB_MA1 M35 TV_DCONSEL0 AJ49 VSS BG29 VSS M42 VSS AJ5 H_D#54 BG30 SA_MA12 M43 PEG_COMPO AJ50 VCC_DMI BG32 VCC_SM M45 PEG_TX0 AJ6 H_D#56 BG33 VCC_SM M46 VSS AJ7 H_D#58 BG35 VCC_SM 159 Ballout and Package Information Ball 160 Signal Ball Signal Ball Signal M47 PEG_RX2 AJ9 H_D#48 BG36 SB_BS2 M49 VSS AK16 VCC_AXG_NCTF BG37 SM_CKE4 M5 VSS AK17 VSS_NCTF BG39 VSS M50 VSS AK19 VCC_AXG_NCTF BG40 SA_DQ22 M6 H_D#3 AK20 VSS BG42 SA_DQ18 M7 H_DSTBN#0 AK21 VSS BG47 SA_DQ10 M9 VSS AK23 VCC_AXM BG48 VSS N1 H_D#31 AK24 VCC_AXM BG5 VSS N11 VSS AK26 VSS BG50 SA_DQ13 N12 H_D#11 AK28 VSS BG51 VSS N14 VSS AK29 VCC_AXM BG8 SA_DM5 N16 H_A#25 AK31 VSS BH12 SB_DM4 N17 VSS AK32 VCC BH17 VSS N19 H_A#35 AK33 VCC_NCTF BH18 SM_ODT0 N2 H_D#26 AK35 VCC_NCTF BH20 RSVD N20 THERMTRIP# AK36 VCC_NCTF BH28 SA_MA3 N23 CFG6 AK37 VCC_NCTF BH30 VSS N24 CFG2 AK50 CL_DATA BH32 VCC_SM N27 CFG1 AK51 VSS BH34 VCC_SM N28 VCCD_QDAC AL1 VSS BH35 VCC_SM N29 VSS AL16 VCC_AXG_NCTF BH39 RSVD N3 H_D#23 AL17 VCC_AXG_NCTF BH44 VSS N32 VSS AL19 VCC_AXG_NCTF BH45 SA_DQ21 N33 CFG19 AL2 VCCA_HPLL BH46 VSS N35 RSVD AL20 VCC_AXG_NCTF BH49 SA_DQ14 N36 VSS AL21 VCC_AXG_NCTF BH5 SB_DQ49 N39 VSS AL23 VCC_AXG_NCTF BH6 SA_DQS5 N40 LVDS_VREFL AL24 VCC_AXM_NCTF BH7 SA_DQS#5 N41 LVDS_VREFH AL26 VCC_AXM_NCTF BH8 VSS N43 PEG_COMPI AL28 VCC_AXM_NCTF BJ1 NC N44 VSS AL29 VCC_AXM_NCTF BJ10 SB_DQ40 N45 PEG_TX#0 AL31 VCC_AXM_NCTF BJ11 VSS N47 PEG_RX#2 AL32 VCC_AXM_NCTF BJ12 SB_DQS4 N49 VSS AL33 VCC_NCTF BJ13 VSS N5 H_D#22 AL35 VCC_NCTF BJ14 SM_ODT2 N50 PEG_TX3 AL36 RSVD BJ15 SM_ODT1 N51 PEG_TX#3 AM11 VSS BJ16 SA_MA13 N7 VSS AM12 RSVD BJ18 RSVD N8 H_D#8 AM13 VSS BJ19 SA_MA0 Datasheet Ballout and Package Information Ball Datasheet Signal Ball Signal Ball Signal N9 H_D#12 AM15 VCC_AXG_NCTF BJ2 SB_DQ55 P13 H_D#14 AM16 VCC_AXG_NCTF BJ20 RSVD P15 H_A#18 AM17 VSS_NCTF BJ23 VCC_SM_CK P19 VSS AM19 VCC_AXG_NCTF BJ24 VCC_SM_CK P2 VSS AM2 VCCA_MPLL BJ25 SA_MA7 P23 VSS AM20 VCC_AXG_NCTF BJ27 SA_MA6 P27 CFG0 AM21 VCC_AXG_NCTF BJ29 SA_MA_14 P29 VSS AM23 VCC_AXG_NCTF BJ32 VCC_SM P3 VSS AM24 VSS_NCTF BJ33 VCC_SM P33 TV_DCONSEL1 AM26 VCC_AXM_NCTF BJ34 VCC_SM P36 RSVD AM28 VCC_AXM_NCTF BJ36 SB_DQ27 P37 RSVD AM29 VCC_AXM_NCTF BJ37 SB_DQ26 P4 H_D#29 AM3 VSS BJ38 VSS P50 VSS AM31 VCC_AXM_NCTF BJ4 VSS R1 VTT AM32 VCC_AXM_NCTF BJ40 SB_DQ29 R17 H_A#19 AM33 VCC_AXM_NCTF BJ41 SB_DQ24 R2 VTT AM35 VCC_NCTF BJ42 VSS R20 VCC_AXG AM36 RSVD BJ43 SB_DQ18 R24 CFG10 AM37 RSVD BJ44 SB_DQ17 R28 VSS AM39 DMI_TXP2 BJ45 SA_DQ11 R3 VTT AM4 VSS BJ46 VSS R30 VCC AM40 DMI_TXN2 BJ50 SB_DQ16 R32 TEST2 AM41 VSS BJ51 NC R35 RSVD AM43 DMI_TXP3 BJ6 SB_DQ47 R49 VSS AM44 DMI_TXN3 BJ7 SB_DM5 R50 PEG_TX#4 AM45 VSS BJ8 SB_DQ46 R51 PEG_TX4 AM47 DMI_RXP0 BK1 NC T10 VTT AM49 CL_CLK BK10 SB_DQ45 T11 VTT AM5 HPLL_CLK BK11 SB_DQ34 T13 VTT AM50 CL_VREF BK12 SB_DQS#4 T14 VCC_AXG AM7 HPLL_CLK# BK13 SB_DQ32 T17 VCC_AXG_NCTF AM8 SA_DQ58 BK14 SM_RCOMP# T18 VCC_AXG_NCTF AM9 SA_DQ62 BK15 VSS T19 VCC_AXG_NCTF AN1 VSS BK16 SM_CS#1 T2 VTT AN10 SA_DQ59 BK17 VSS T21 VCC_AXG_NCTF AN11 SA_DQ63 BK18 RSVD T22 VCC_AXG_NCTF AN13 RSVD BK19 SA_BS1 T23 VCC_AXG_NCTF AN14 VCC_AXG BK2 NC T25 VCC_AXG_NCTF AN2 VCCD_HPLL BK20 RSVD 161 Ballout and Package Information Ball 162 Signal Ball Signal Ball Signal T27 VSS_NCTF AN3 SA_DQ57 BK22 RSVD T29 VSS AN38 VSS BK23 VCC_SM_CK T3 VTT AN39 VSS BK24 VCC_SM_CK T30 VCC_NCTF AN41 DMI_RXP2 BK25 VSS T31 VSS AN42 DMI_RXN2 BK27 SA_MA2 T33 VSS AN43 VSS BK28 SA_MA5 T34 VCC_NCTF AN45 DMI_RXP3 BK29 VSS T35 VCC_NCTF AN46 DMI_RXN3 BK3 SB_DQ52 T37 VSS_NCTF AN47 DMI_RXN0 BK31 SM_RCOMP_VOH T38 PEG_TX1 AN49 CL_RST# BK32 VCC_SM T39 VSS AN5 VSS BK33 VCC_SM T41 PEG_RX5 AN50 SB_DQ5 BK34 VCC_SM T42 PEG_TX#5 AN51 SB_DQ4 BK35 VCC_SM T43 VSS AN6 SA_DM7 BK36 VSS T45 PEG_RX#3 AN7 VSS BK37 SB_DQ31 T46 PEG_TX2 AN9 SA_DQ61 BK38 SB_DQS#3 T47 VSS AP15 VCC_AXG_NCTF BK39 SB_DQS3 T49 PEG_RX4 AP16 VCC_AXG_NCTF BK40 VSS T5 VTT AP17 VCC_AXG_NCTF BK41 SB_DQ28 T50 PEG_RX#4 AP19 VCC_AXG_NCTF BK42 SB_DQ23 T6 VTT AP2 SA_DQS#7 BK43 SB_DQ22 T7 VTT AP20 VCC_AXG_NCTF BK44 VSS T9 VTT AP21 VCC_AXG_NCTF BK45 SB_DM2 U1 VTT AP23 VCC_AXG_NCTF BK46 SB_DQS2 U11 VTT AP24 VCC_AXG_NCTF BK47 SB_DQ20 U12 VTT AP26 VSS_NCTF BK49 SB_DQ21 U13 VTT AP28 VSS_NCTF BK5 SB_DQ42 U15 VCC_AXG_NCTF AP29 VCC_AXM_NCTF BK50 NC U16 VCC_AXG_NCTF AP3 SA_DQS7 BK51 NC U17 VCC_AXG_NCTF AP31 VCC_AXM_NCTF BK6 VSS U19 VCC_AXG_NCTF AP32 VCC_AXM_NCTF BK7 SB_DQS#5 U2 VTT AP33 VCC_AXM_NCTF BK8 VSS U20 VCC_AXG_NCTF AP35 VCC_NCTF BK9 SB_DQ44 U21 VCC_AXG_NCTF AP36 VCC_NCTF BL1 VSS_SCB4 U23 VCC_AXG_NCTF AP4 VSS BL11 VSS U24 VSS_NCTF AP48 VSS BL13 VSS U26 VCC_AXG_NCTF AP49 SB_DQ0 BL15 SM_RCOMP U28 VSS_NCTF AP50 VSS BL17 SA_CAS# U29 VCC_NCTF AR1 SB_DQ58 BL19 VSS Datasheet Ballout and Package Information Ball 15.4 Signal Ball Signal Ball Signal U3 VTT AR11 VSS BL2 NC U31 VCC_NCTF AR12 RSVD BL22 VSS U32 VCC_NCTF AR13 RSVD BL24 SA_MA4 U33 VCC_NCTF AR15 VSS_NCTF BL28 SA_MA8 U35 VCC_NCTF AR16 VCCA_SM_NCTF BL3 NC U36 VCC_NCTF AR17 VCCA_SM_NCTF BL31 SM_RCOMP_VOL U39 PEG_TX#1 AR19 VSS_NCTF BL33 VCC_SM U40 PEG_RX#5 AR2 VSS BL35 SB_DQ30 U41 VSS AR20 VCC_AXG_NCTF BL37 VSS U43 PEG_TX5 AR21 VCC_AXG_NCTF BL39 SB_DM3 U44 PEG_RX3 AR23 VCC_AXG_NCTF BL41 SB_DQ25 U45 VSS AR24 VCC_AXG_NCTF BL43 SB_DQ19 U47 PEG_TX#2 AR26 VCC_AXG_NCTF BL45 SB_DQS#2 U48 VCCD_PEG_PLL AR28 VSS_NCTF BL47 VSS U5 VTT AR29 VCC_AXD_NCTF BL49 NC U50 VSS AR31 VCC_AXM_NCTF BL5 SB_DQ43 U51 VCCA_PEG_PLL AR32 VCC_AXM_NCTF BL50 NC U7 VTT AR33 VCC_AXM_NCTF BL51 VSS_SCB5 U8 VTT AR35 VCC_NCTF BL7 SB_DQS5 U9 VTT AR36 VCC_NCTF BL9 SB_DQ41 Package The (G)MCH is provided in an 1299-ball, FCBGA package. Caution: Avoid contacting the capacitors with electrically conductive materials. Doing so may short the capacitors and possibly damage the device or render it inactive. * Tolerances: -- X: 0.1 -- XX: 0.05 * Angles: 1.0 degrees * Package parameters: 35.0 mm x 35.0 mm * Land metal diameter: 524 microns * Solder resist opening: 430 microns Datasheet 163 Ballout and Package Information Figure 25. (G)MCH Mechanical Drawing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apacitor Area, Handling Keep Out Zone: Handling refers to any equipment such as pick and place, trays, or shipping media. Capacitor Area Handling Keep Out Zone means all equipment mentioned above should stay out of this area to not interfere with capacitors that may be placed in this area. Use of an insulating material between the capacitors and any thermal solution is recommended to prevent capacitor shorting. Handling Area, Package Keep Out Zone: Package Keep Out Zone means capacitors 2. may not be placed in this area since this is the area where we allow handling; that is, pick and place. 3. Dimensions are in millimeters. 4. Unless otherwise specified, interpret the dimensions and tolerances in accordance with ASME Y14.5-1994. 164 Datasheet (G)MCH Register Description 16 (G)MCH Register Description 16.1 Register Terminology Abbreviation Definition RO Read Only bit(s). Writes to these bits have no effect. This may be a status bit or a static value. RS/WC Read Set / Write Clear bit(s). The first time the bit is read with an enabled byte, it returns the value 0, but a side-effect of the read is that the value changes to 1. Any subsequent reads with enabled bytes return a 1 until a 1 is written to the bit. When the bit is read, but the byte is not enabled, the state of the bit does not change, and the value returned is irrelevant, but will match the state of the bit. When a 0 is written to the bit, there is no effect. When a 1 is written to the bit, its value becomes 0, until the next byte-enabled read. When the bit is written, but the byte is not enabled, there is no effect. Datasheet R/W Read / Write bit(s). These bits can be read and written by software. Hardware may only change the state of this bit by reset. R/WC Read / Write Clear bit(s). These bits can be read. Internal events may set this bit. A software write of 1 clears (sets to 0) the corresponding bit(s) and a write of 0 has no effect. R/WC/S Read / Write Clear / Sticky bit(s). These bits can be read. Internal events may set this bit. A software write of 1 clears (sets to 0) the corresponding bit(s) and a write of 0 has no effect. Bits are not cleared by "warm" reset, but will be reset with a cold/complete reset (for PCI Express related bits a cold reset is "Power Good Reset" as defined in the PCI Express spec). R/W/B Read / Write / Blind bit(s). These bits can be read and written by software. Additionally there is a selector bit which, when set, changes what may be read from these bits. The value written is always stored in a hidden register. When the selector bit indicates that the written value should not be read, some other status is read from this bit. When the selector bit indicates that the written value should be read, the value in the hidden register is read from this bit. R/W/K Read / Write / Key bit(s). These bits can be read and written by software. Additionally this bit, when set, prohibits some other bit field(s) from being writeable (bit fields become Read Only). R/W/L Read / Write / Lockable bit(s). These bits can be read and written by software. Additionally there is a Key bit (which is marked R/W/K or R/W/L/K) that, when set, prohibits this bit field from being writeable (bit field becomes Read Only). R/W/L/K Read / Write / Lockable / Key bit(s). These bits can be read and written by software. Additionally this bit is a Key bit that, when set, prohibits this bit field and/or some other specified bit fields from being writeable (bit fields become Read Only). 165 (G)MCH Register Description Abbreviation 166 Definition R/W/S Read / Write / Sticky bit(s). These bits can be read and written by software. Bits are not cleared by "warm" reset, but will be reset with a cold/complete reset (for PCI Express related bits a cold reset is "Power Good Reset" as defined in the PCI Express spec). R/WSC Read / Write Self Clear bit(s). These bits can be read and written by software. When the bit is 1, hardware may clear the bit to 0 based upon internal events, possibly sooner than any subsequent software read could retrieve a 1. R/WSC/L Read / Write Self Clear / Lockable bit(s). These bits can be read and written by software. When the bit is 1, hardware may clear the bit to 0 based upon internal events, possibly sooner than any subsequent software read could retrieve a 1. Additionally there is a bit (which is marked R/W/K or R/W/L/K) that, when set, prohibits this bit field from being writeable (bit field becomes Read Only). R/WC Read Write Clear bit(s). These bits can be read and written by software. However, a write of 1 clears (sets to 0) the corresponding bit(s) and a write of 0 has no effect. R/WO Write Once bit(s). Once written by software, bits with this attribute become Read Only. These bits can only be cleared by a Reset. W Write Only. These bits may be written by software, but will always return zeros when read. They are used for write side-effects. Any data written to these registers cannot be retrieved. Datasheet (G)MCH Configuration Process and Registers 17 (G)MCH Configuration Process and Registers 17.1 Platform Configuration Structure The DMI physically connects the (G)MCH and the ICH; so, from a configuration standpoint, the DMI is logically PCI Bus 0. As a result, all devices internal to the (G)MCH and the ICH appear to be on PCI Bus 0. The system's primary PCI expansion bus is physically attached to the ICH and, from a configuration perspective, appears to be a hierarchical PCI bus behind a PCI-to-PCI bridge and therefore has a programmable PCI Bus number. The PCI Express X16 graphics attach appears to system software to be a real PCI bus behind a PCI-to-PCI bridge that is a device resident on PCI Bus 0. Note: A physical PCI Bus 0 does not exist and that DMI and the internal devices in the (G)MCH and ICH logically constitute PCI Bus 0 to configuration software. Datasheet 167 (G)MCH Configuration Process and Registers Figure 27. Conceptual Chipset Platform PCI Configuration Diagram 168 Datasheet (G)MCH Configuration Process and Registers The (G)MCH contains three PCI devices within a single physical component. The configuration registers for the three devices are mapped as devices residing on PCI Bus 0. Device 0: Host Bridge/DRAM Controller. Logically this appears as a PCI device residing on PCI Bus 0. Device 0 contains the standard PCI header registers, PCI Express base address register, DRAM control (including thermal/throttling control), configuration for the DMI, and other (G)MCH-specific registers. Device 1: Host-PCI Express Bridge. Logically this appears as a "virtual" PCI-to-PCI bridge residing on PCI Bus 0 and is compliant with PCI Express Specification Revision 1.0. Device 1 contains the standard PCI-to-PCI bridge registers and the standard PCI Express/PCI configuration registers (including the PCI Express memory address mapping). It also contains Isochronous and Virtual Channel controls in the PCI Express extended configuration space. Device 2: Internal Graphics Control. Logically, this appears as a PCI device residing on PCI Bus 0. Physically, Device 2 contains the configuration registers for 3D, 2D, and display functions. 17.2 Configuration Mechanisms The CPU is the originator of configuration cycles so the FSB is the only interface in the platform where these mechanisms are used. Internal to the (G)MCH transactions received through both configuration mechanisms are translated to the same format. Datasheet 169 (G)MCH Configuration Process and Registers Figure 28. Chipset Configuration Paths and Transaction Types 17.2.1 Standard PCI Configuration Mechanism A detailed description of the mechanism for translating CPU I/O bus cycles to configuration cycles is described below. The PCI specification defines a slot based "configuration space" that allows each device to contain up to eight functions with each function containing up to 256, 8-bit configuration registers. The PCI specification defines two bus cycles to access the PCI 170 Datasheet (G)MCH Configuration Process and Registers configuration space: Configuration Read and Configuration Write. Memory and I/O spaces are supported directly by the CPU. Configuration space is supported by a mapping mechanism implemented within the (G)MCH. The configuration access mechanism makes use of the CONFIG_ADDRESS Register (at I/O address 0CF8h though 0CFBh) and CONFIG_DATA Register (at I/O address 0CFCh though 0CFFh). To reference a configuration register a DW I/O write cycle is used to place a value into CONFIG_ADDRESS that specifies the PCI bus, the device on that bus, the function within the device and a specific configuration register of the device function being accessed. CONFIG_ADDRESS[31] must be 1 to enable a configuration cycle. CONFIG_DATA then becomes a window into the four bytes of configuration space specified by the contents of CONFIG_ADDRESS. Any read or write to CONFIG_DATA will result in the (G)MCH translating the CONFIG_ADDRESS into the appropriate configuration cycle. The (G)MCH is responsible for translating and routing the CPU's I/O accesses to the CONFIG_ADDRESS and CONFIG_DATA registers to internal (G)MCH configuration registers, DMI or PCI Express. 17.2.2 Logical PCI Bus 0 Configuration Mechanism The (G)MCH decodes the Bus Number (bits 23:16) and the Device Number fields of the CONFIG_ADDRESS register. If the Bus Number field of CONFIG_ADDRESS is 0 the configuration cycle is targeting a PCI Bus 0 device. The Host-DMI Bridge entity within the (G)MCH is hardwired as Device 0 on PCI Bus 0. The Host-PCI Express Bridge entity within the (G)MCH is hardwired as Device 1 on PCI Bus 0. Device 2 contains the control registers for the Integrated Graphics Controller. The ICH decodes the Type 0 access and generates a configuration access to the selected internal device. 17.2.3 Primary PCI and Downstream Configuration Mechanism If the Bus Number in the CONFIG_ADDRESS is non-zero, and falls outside the range claimed by the Host-PCI Express bridge (not between the upper bound of the bridge device's Subordinate Bus Number register and the lower bound of the bridge device's Secondary Bus Number register), the (G)MCH will generate a Type 1 DMI Configuration Cycle. A[1:0] of the DMI request packet for the Type 1 configuration cycle will be "01". Bits 31:2 of the CONFIG_ADDRESS register will be translated to the A[31:2] field of the DMI request packet of the configuration cycle as shown below. This DMI configuration cycle will be sent over the DMI. If the cycle is forwarded to the ICH via the DMI, the ICH compares the non-zero Bus Number with the Secondary Bus Number and Subordinate Bus Number registers of its PCI-to-PCI bridges to determine if the configuration cycle is meant for Primary PCI, one of the ICH's devices, the DMI, or a downstream PCI bus. Datasheet 171 (G)MCH Configuration Process and Registers Figure 29. DMI Type 0 Configuration Address Translation CONFIG_ADDRESS 3 1 1 2 2 8 7 Reserve d 2 2 4 3 0 1 1 6 5 1 1 1 0 Device Number 0 8 7 2 1 0 Function Register Number x x DMI Type 0 Configuration Address Extension 3 1 2 2 8 7 2 2 4 3 1 1 6 5 1 1 1 0 Device Number Reserved 8 7 2 1 0 Function Register Number 0 0 Figure 30. DMI Type 1 Configuration Address Translation CONFIG_ADDRESS 3 1 1 2 2 8 7 Reserve d 2 2 4 3 0 1 1 6 5 1 1 1 0 Device Number Bus Number 8 7 2 1 0 Function Register Number x x DMI Type 1 Configuration Address Extension 3 1 2 2 8 7 Reserved 17.2.4 2 2 4 3 1 1 6 5 Bus Number 1 1 1 0 Device Number 8 7 2 1 0 Function Register Number 0 1 PCI Express Enhanced Configuration Mechanism PCI Express extends the configuration space to 4096 bytes per device/function as compared to 256 bytes allowed by PCI Specification Revision 2.3. PCI Express configuration space is divided into a PCI 2.3-compatible region, which consists of the first 256 bytes of a logical device's configuration space and a PCI Express extended region which consists of the remaining configuration space. The PCI-compatible region can be accessed using either the mechanism defined in the previous Standard PCI Configuration Mechanism or using the PCI Express Enhanced Configuration Mechanism described in this section. The extended configuration registers may only be accessed using the PCI Express Enhanced Configuration Mechanism. To maintain compatibility with PCI configuration addressing mechanisms, system software must access the extended configuration space using 32-bit operations (32-bit aligned) only. These 32-bit operations include byte enables allowing only appropriate bytes within the Dword to be accessed. Locked transactions to the PCI Express memory mapped configuration address space are not supported. All changes made using either access mechanism are equivalent. The PCI Express Enhanced Configuration Mechanism utilizes a flat memory-mapped address space to access device configuration registers. This address space is reported 172 Datasheet (G)MCH Configuration Process and Registers by the system firmware to the operating system. There is a register, PCIEXBAR, which defines the base address for the block of addresses below top 4 GB for the configuration space associated with busses, devices and functions that are potentially a part of the PCI Express root complex hierarchy. In the PCIEXBAR register there exist controls to limit the size of this reserved memory mapped space. 256 MB is the amount of address space required to reserve space for every bus, device, and function that could possibly exist. Options for 128 MB and 64 MB exist in order to free up those addresses for other uses. In these cases, the number of busses and all of their associated devices and functions are limited to 128 or 64 busses, respectively. The PCI Express Configuration Transaction Header includes an additional 4 bits (ExtendedRegisterAddress[3:0]) between the Function Number and Register Address fields to provide indexing into the 4 KB of configuration space allocated to each potential device. For PCI Compatible Configuration Requests, the Extended Register Address field must be all zeros. Datasheet 173 (G)MCH Configuration Process and Registers Figure 31. Memory Map to PCI Express Device Configuration Space 0xFFFFFFF 0x7FFF 0xFFFFF Bus 255 Device 31 0xFFF Function 7 PCI Express Extended Conf iguration Space 0xFF 0xFFFF 0x1FFFFF 0x1FFF Bus 1 0x7FFF 0xFFFFF Bus 0 Function 1 Device 1 0x3F 0xFFF Device 0 Function 0 PCI Compatible Conf iguration Space PCI Compatible Conf iguration Space Header 0 Located by PCI Express Base Address As with PCI devices, each device is selected based on decoded address information that is provided as a part of the address portion of Configuration Request packets. A PCI Express device will decode all address information fields (bus, device, function and extended address numbers) to provide access to the correct register. To access this space (steps 1, 2, 3 are done only once by BIOS): 17.3 1. Use the PCI compatible configuration mechanism to enable the PCI Express enhanced configuration mechanism by writing 1 to bit 0 of the PCIEXBAR register. 2. Use the PCI compatible configuration mechanism to write an appropriate PCI Express base address into the PCIEXBAR register. 3. Calculate the host address of the register you wish to set using (PCI Express base + (bus number * 1 MB) + (device number * 32 KB) + (function number * 4 KB) + (1 B * offset within the function) = host address). 4. Use a memory write or memory read cycle to the calculated host address to write or read that register. Routing Configuration Accesses The (G)MCH supports two PCI related interfaces: DMI and PCI Express Graphics. The (G)MCH is responsible for routing PCI and PCI Express configuration cycles to the appropriate device that is an integrated part of the (G)MCH or to one of these two interfaces. Configuration cycles to the ICH internal devices and Primary PCI (including downstream devices) are routed to the ICH via DMI. Configuration cycles to both the PCI Express Graphics PCI compatibility configuration space and the PCI Express Graphics extended configuration space are routed to the PCI Express Graphics port device or associated link. 174 Datasheet (G)MCH Configuration Process and Registers Figure 32. (G)MCH Configuration Cycle Flowchart DW I/O Write to CONFIG_ADDRESS with bit 31 = 1 I/O Read/Write to CONFIG_DATA Bus# = 0 Yes No GMCH Generates Type 1 Access to PCI Express Yes Bus# > SEC BUS Bus# SUB BUS in GMCH Dev 1 No Yes Bus#= SECONDARYBUS in GMCH Dev 1 No Device# = 0 & Function# = 0 Yes GMCH Claims Yes GMCH Claims No Device# = 1 & Dev # 1 Enabled & Function# = 0 No Device# = 2 & GMCH Generates DMI Type 1 Configuration Cycle Device# = 0 No MCH allows cycleto go to DMI resulting in Master Abort 17.3.1 Yes (Function# = 0 & Dev# Yes 2 Func# 0 Enabled) OR (Function# = 1 & Dev# 2 Funcs# 0 and 1 Enabled) GMCH Claims GMCH Generates Type 0 Access to PCI Express No GMCH Generates DMI Type 0 Configuration Cycle Internal Device Configuration Accesses The (G)MCH decodes the Bus Number (bits 23:16) and the Device Number fields of the CONFIG_ADDRESS register. If the Bus Number field of CONFIG_ADDRESS is 0 the configuration cycle is targeting a PCI Bus 0 device. If the targeted PCI Bus 0 device exists in the (G)MCH and is not disabled, the configuration cycle is claimed by the appropriate device. Datasheet 175 (G)MCH Configuration Process and Registers 17.3.2 Bridge Related Configuration Accesses Configuration accesses on PEG or DMI are PCI Express Configuration TLPs. Bus Number [7:0] is Header Byte 8 [7:0] Device Number [4:0] is Header Byte 9 [7:3] Function Number [2:0] is Header Byte 9 [2:0] And special fields for this type of TLP: Extended Register Number [3:0] is Header Byte 10 [3:0] Register Number [5:0] is Header Byte 11 [7:2] See the PCI Express specification for more information on both the PCI 2.3-compatible and PCI Express Enhanced Configuration Mechanism and transaction rules. 17.3.2.1 PCI Express Graphics Configuration Accesses When the Bus Number of a type 1 Standard PCI Configuration cycle or PCI Express Enhanced Configuration access matches the Device 1 Secondary Bus Number, a PCI Express Type 0 Configuration TLP is generated on the PEG link targeting the device directly on the opposite side of the link. This should be Device 0 on the bus number assigned to the PEG link (likely Bus 1). The device on other side of link must be Device 0. The (G)MCH will Master Abort any Type 0 Configuration access to a non-zero Device number. If there is to be more than one device on that side of the link there must be a bridge implemented in the downstream device. When the Bus Number of a type 1 Standard PCI Configuration cycle or PCI Express Enhanced Configuration access is within the claimed range (between the upper bound of the bridge device's Subordinate Bus Number register and the lower bound of the bridge device's Secondary Bus Number register) but doesn't match the Device 1 Secondary Bus Number, a PCI Express Type 1 Configuration TLP is generated on the secondary side of the PEG link. PCI Express Configuration Writes: * Internally the host interface unit will translate writes to PCI Express extended configuration space to configuration writes on the backbone. * Writes to extended space are posted on the FSB, but non-posted on the PEG or DMI (i.e., translated to configuration writes). 17.3.2.2 DMI Configuration Accesses Accesses to disabled (G)MCH internal devices, bus numbers not claimed by the HostPEG bridge, or PCI Bus 0 devices not part of the (G)MCH will subtractively decode to the ICH and consequently be forwarded over the DMI via a PCI Express configuration TLP. 176 Datasheet (G)MCH Configuration Process and Registers If the Bus Number is zero, the (G)MCH will generate a Type 0 Configuration Cycle TLP on DMI. If the Bus Number is non-zero, and falls outside the range claimed by the Host-PEG bridge, the (G)MCH will generate a Type 1 Configuration Cycle TLP on DMI. The ICH routes configurations accesses in a manner similar to the (G)MCH. The ICH decodes the configuration TLP and generates a corresponding configuration access. Accesses targeting a device on PCI Bus 0 may be claimed by an internal device. The ICH compares the non-zero Bus Number with the Secondary Bus Number and Subordinate Bus Number registers of its PCI-to-PCI bridges to determine if the configuration access is meant for Primary PCI, or some other downstream PCI bus or PCI Express link. Configuration accesses that are forwarded to the ICH, but remain unclaimed by any device or bridge will result in a master abort. 17.3.2.3 Configuration Retry For both PEG and DMI, any configuration request (read or write) that receives a Configuration Request Retry Completion Status (CRS) will be reissued as a new transaction. The CRS terminates the original request TLP, but the (G)MCH will synthesize a subsequent request. The new config TLP which gets "reissued" due to CRS will have a new Sequence Number, but the TLP fields (tag, address, data, attributes, requestor ID, etc) will be the same as the original TLP. While this is happening, no completion will be sent to the originator of the configuration cycle (the CPU). A completion will not be sent to the CPU until the (G)MCH receives a successful completion, an Unsupported Request or Completer Abort completion, or the completion times out (if completion timeout is enabled). This mechanism mimics the behavior on a legacy PCI bus, where any request that is retried will retry indefinitely. No devices in the ICH ever return CRS. The (G)MCH is the only root complex device that handles CRS. The ICH just forwards to the (G)MCH all completions independent of completion status. 17.4 (G)MCH Registers The (G)MCH internal registers (I/O Mapped, Configuration, and PCI Express Extended Configuration registers) are accessible by the Host CPU. The registers that reside within the lower 256 bytes of each device can be accessed as Byte, Word (16-bit), or Dword (32-bit) quantities, with the exception of CONFIG_ADDRESS which can only be accessed as a Dword. All multi-byte numeric fields use "little-endian" ordering (i.e., lower addresses contain the least significant parts of the field). Registers which reside in bytes 256 through 4095 of each device may only be accessed using memory mapped transactions in Dword (32-bit) quantities. Some of the (G)MCH registers described in this section contain reserved bits. These bits are labeled "Reserved." Software must deal correctly with fields that are reserved. On reads, software must use appropriate masks to extract the defined bits and not rely on reserved bits being any particular value. On writes, software must ensure that the values of reserved bit positions are preserved. That is, the values of reserved bit positions must first be read, merged with the new values for other bit positions and Datasheet 177 (G)MCH Configuration Process and Registers then written back. Note the software does not need to perform read, merge, or write operation for the configuration address register. In addition to reserved bits within a register, the (G)MCH contains address locations in the configuration space of the Host Bridge entity that are marked either "Reserved" or "Intel Reserved." The (G)MCH responds to accesses to Reserved address locations by completing the host cycle. When a Reserved register location is read, a zero value is returned. (Reserved registers can be 8-, 16-, or 32-bit in size). Writes to Reserved registers have no effect on the (G)MCH. Registers that are marked as Intel Reserved must not be modified by system software. Writes to Intel Reserved registers may cause system failure. Reads to Intel Reserved registers may return a non-zero value. Upon a Full Reset, the (G)MCH sets all of its internal configuration registers to predetermined default states. Some register values at reset are determined by external strapping options, or the states of poly-silicon fuses. The default state represents the minimum functionality feature set required to successfully bring up the system. Hence, it does not represent the optimal system configuration. It is the responsibility of the system initialization software (usually BIOS) to properly determine the DRAM configurations, operating parameters and optional system features that are applicable, and to program the (G)MCH registers accordingly. 17.5 I/O Mapped Registers The (G)MCH contains two registers that reside in the CPU I/O address space - the Configuration Address (CONFIG_ADDRESS) Register and the Configuration Data (CONFIG_DATA) Register. The Configuration Address Register enables/disables the configuration space and determines what portion of configuration space is visible through the Configuration Data window. 178 Datasheet (G)MCH Configuration Process and Registers 17.5.1 CONFIG_ADDRESS--Configuration Address Register I/O Address: Size: 0CF8h Accessed as a DW 32 bits CONFIG_ADDRESS is a 32-bit register that can be accessed only as a DW. A Byte or Word reference will "pass through" the Configuration Address Register and DMI onto the PCI_A bus as an I/O cycle. The CONFIG_ADDRESS register contains the Bus Number, Device Number, Function Number, and Register Number for which a subsequent configuration access is intended. Bit Access Default Value 31 R/W 0b Description Configuration Enable (CFGE): When this bit is set to 1, accesses to PCI configuration space are enabled. If this bit is reset to 0, accesses to PCI configuration space are disabled. 30:24 RO 00h Reserved 23:16 R/W 00h Bus Number: If the Bus Number is programmed to 00h, the target of the Configuration Cycle is a PCI Bus 0 agent. If this is the case and the (G)MCH is not the target (i.e., the device number is >=3 and not equal to 7), then a DMI Type 0 Configuration Cycle is generated. If the Bus Number is non-zero, and does not fall within the ranges enumerated by Device 1's Secondary Bus Number or Subordinate Bus Number Register, then a DMI Type 1 Configuration Cycle is generated. If the Bus Number is non-zero and matches the value programmed into the Secondary Bus Number Register of Device 1, a Type 0 PCI Configuration cycle will be generated on PCI Express-G. If the Bus Number is non-zero, greater than the value in the Secondary Bus Number register of Device 1 and less than or equal to the value programmed into the Subordinate Bus Number Register of Device 1 a Type 1 PCI configuration cycle will be generated on PCI Express-G. This filed is mapped to byte 8 [7:0] of the request header format during PCI Express Configuration cycles and A[23:16] during the DMI Type 1 configuration cycles. 15:11 R/W 00h Device Number: This field selects one agent on the PCI bus selected by the Bus Number. When the Bus Number field is "00" the (G)MCH decodes the Device Number field. The (G)MCH is always Device 0 for the Host bridge entity, Device 1 for the Host-PCI Express entity. Therefore, when the Bus Number=0 and the device equals 0, 1, 2 or 7 the internal (G)MCH devices are selected. This field is mapped to byte 6 [7:3] of the request header format during PCI Express and DMI Configuration cycles. Datasheet 179 (G)MCH Configuration Process and Registers Bit Access Default Value 10:8 R/W 000b Description Function Number: This field allows the configuration registers of a particular function in a multi-function device to be accessed. The (G)MCH ignores configuration cycles to its internal devices if the function number is not equal to 0 or 1. This field is mapped to byte 6 [2:0] of the request header format during PCI Express and DMI Configuration cycles. 7:2 R/W 00h Register Number: This field selects one register within a particular Bus, Device, and Function as specified by the other fields in the Configuration Address Register. This field is mapped to byte 7 [7:2] of the request header format during PCI Express and DMI Configuration cycles. 1:0 17.5.2 RO 00b Reserved CONFIG_DATA--Configuration Data Register I/O Address: Size: 0CFCh 32 bits CONFIG_DATA is a 32-bit read/write window into configuration space. The portion of configuration space that is referenced by CONFIG_DATA is determined by the contents of CONFIG_ADDRESS. Bit Access Default Value 31:0 R/W 0000 0000h Description Configuration Data Window (CDW): If bit 31 of CONFIG_ADDRESS is 1, any I/O access to the CONFIG_DATA register will produce a configuration transaction using the contents of CONFIG_ADDRESS to determine the Bus, Device, Function, and Offset of the register to be accessed. 180 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18 Host Bridge Device 0 Configuration Registers (D0:F0) Warning: Address locations that are note listed are considered Reserved registers locations. Reads to Reserved registers may return non-zero values. Writes to reserved locations may cause system failures. 18.1 Device 0 Configuration Registers Register Name Register Symbol Register End Default Value Access Vendor Identification VID 0 1 8086h RO Device Identification DID 2 3 2A00h1 RO PCI Command PCICMD 4 5 0006h RO; R/W PCI Status PCISTS 6 7 0090h RO; R/WC Revision Identification RID 8 8 00h RO Class Code CC 9 B 060000h RO C C 2A10h2 Reserved Master Latency Timer MLT D D 00h RO Header Type HDR E E 00h RO F 2B Reserved Subsystem Vendor Identification SVID 2C 2D 0000h R/WO Subsystem Identification SID 2E 2F 0000h R/WO 30 33 Reserved Datasheet Register Start Capabilities Pointer CAPPTR 34 34 E0h RO Egress Port Base Address EPBAR 40 47 0000000000 000000h R/W/L; RO; R/W 181 Host Bridge Device 0 Configuration Registers (D0:F0) Register Name (G)MCH Memory Mapped Register Range Base Register Symbol MCHBAR Reserved Register End 48 4F 50 51 Default Value Access 0000000000 000000h R/W/L; RO; R/W (G)MCH Graphics Control Register (Device 0) GGC 52 53 0030h RO; R/W/L Device Enable DEVEN 54 57 000043DBh RO; R/W/L 58 5F Reserved PCI Express Register Range Base Address PCIEXBAR 60 67 00000000E0 000000h R/W/L; RO; R/W MCH-ICH Serial Interconnect Ingress Root Complex DMIBAR 68 6F 0000000000 000000h R/W; R/W/L; RO 70 77 78 7B 00000000h R/W/L; RO 7C 8F Reserved PM I/O BAR Register Definition PMIOBAR Reserved 182 Register Start Programmable Attribute Map 0 PAM0 90 90 00h RO; R/W/L Programmable Attribute Map 1 PAM1 91 91 00h RO; R/W/L Programmable Attribute Map 2 PAM2 92 92 00h RO; R/W/L Programmable Attribute Map 3 PAM3 93 93 00h RO; R/W/L Programmable Attribute Map 4 PAM4 94 94 00h RO; R/W/L Programmable Attribute Map 5 PAM5 95 95 00h RO; R/W/L Programmable Attribute Map 6 PAM6 96 96 00h RO; R/W/L Legacy Access Control LAC 97 97 00h R/W/L; RO Remap Base Address Register REMAPBASE 98 99 03FFh RO; R/W/L Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) Register Name Remap Limit Address Register Register Symbol REMAPLIMIT Reserved Register Start Register End 9A 9B 9C 9C Default Value Access 0000h RO; R/W/L System Management RAM Control SMRAM 9D 9D 02h RO; R/W/L; R/W Extended System Management RAM Control ESMRAMC 9E 9E 38h R/W/L; R/WC; RO 9F 9F Reserved Top Of Memory TOM A0 A1 0001h RO; R/W/L Top of Upper Usable DRAM TOUUD A2 A3 0000h R/W/L A4 AF B0 B1 0010h R/W/L; RO B2 C7 Reserved Top of Low Used DRAM Register TOLUD Reserved Error Status ERRSTS C8 C9 0000h RO; R/WC/S Error Command ERRCMD CA CB 0000h RO; R/W CC DB Reserved Scratchpad Data SKPD DC DF 00000000h R/W Capability Identifier CAPID0 E0 E9 0000000000 00010A0009 h RO (G)MCH Dev0 Test CRLT F0 F0 00h RO; R/WO F1 FF Reserved NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel(R) GME965 and GLE960 Express Chipsets. 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only. Datasheet 183 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.1 VID - Vendor Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 0-1h 8086h RO 16 bits Bit Access Default Value 15:0 RO 8086h Description Vendor Identification Number (VID): PCI standard identification for Intel. 18.1.2 DID - Device Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 2-3h 2A00h RO 16 bits Bit Access Default Value Description 15:0 RO 2A00h1 Device Identification Number (DID): 2A10h2 Identifier assigned to the (G)MCH core/primary PCI device. NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets. 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only. 18.1.3 PCICMD - PCI Command B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 4-5h 0006h RO; R/W 16 bits Bit Access Default Value 15:10 RO 00h 9 RO 0b Description Reserved Fast Back-to-Back Enable (FB2B): This bit controls whether or not the master can do fast backto-back write. Since Device 0 is strictly a target this bit is not implemented and is hardwired to 0. Writes to this bit position have no effect. 184 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) Bit Access Default Value 8 R/W 0b Description SERR Enable (SERRE): This bit is a global enable bit for Device 0 SERR messaging. The (G)MCH does not have an SERR signal. The (G)MCH communicates the SERR condition by sending an SERR message over (G)MCH ICH Serial Interface (DMI) to the ICH. If this bit is set to a 1, the (G)MCH is enabled to generate SERR messages over DMI for specific Device 0 error conditions that are individually enabled in the ERRCMD register. The error status is reported in the ERRSTS and PCISTS registers. If SERRE is clear, then the SERR message is not generated by the (G)MCH for Device 0. Note that this bit only controls SERR messaging for the Device 0. Device 1 has its own SERRE bits to control error reporting for error conditions occurring on their respective devices. The control bits are used in a logical OR manner to enable the SERR DMI message mechanism. 7 RO 0b Address/Data Stepping Enable (ADSTEP): Address/data stepping is not implemented in the (G)MCH, and this bit is hardwired to 0. Writes to this bit position have no effect. 6 RO 0b Parity Error Enable (PERRE): PERRB is not implemented by the (G)MCH and this bit is hardwired to 0. Writes to this bit position have no effect. 5 RO 0b VGA Palette Snoop Enable (VGASNOOP): The (G)MCH does not implement this bit and it is hardwired to a 0. Writes to this bit position have no effect. 4 RO 0b Memory Write and Invalidate Enable (MWIE): The (G)MCH will never issue memory write and invalidate commands. This bit is therefore hardwired to 0. Writes to this bit position will have no effect. 3 RO 0b Special Cycle Enable (SCE): The (G)MCH does not implement this bit and it is hardwired to a 0. Writes to this bit position have no effect. 2 RO 1b Bus Master Enable (BME): The (G)MCH is always enabled as a master on DMI. This bit is hardwired to a 1. Writes to this bit position have no effect. 1 RO 1b Memory Access Enable (MAE): The (G)MCH always allows access to main memory. This bit is not implemented and is hardwired to 1. Writes to this bit position have no effect. 0 RO 0b I/O Access Enable (IOAE): This bit is not implemented in the (G)MCH and is hardwired to a 0. Writes to this bit position have no effect. Datasheet 185 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.4 PCISTS - PCI Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 6-7h 0090h RO; R/WC 16 bits Bit Access Default Value 15 RO 0b Description Detected Parity Error (DPE): The (G)MCH does not implement this bit and it is hardwired to a 0. Writes to this bit position have no effect. 14 R/WC 0b Signaled System Error (SSE): This bit is set to 1 when the (G)MCH Device 0 generates an SERR message over DMI for any enabled Device 0 error condition or Device 0 error conditions are enabled in the PCICMD and ERRCMD registers. Device 0 error flags are read/reset from the PCISTS or ERRSTS registers. Software clears this bit by writing a 1 to it. 13 R/WC 0b Received Unsupported Request (RURS): This bit is set when the (G)MCH generates a DMI request that receives a Unsupported request completion. Software clears this bit by writing a 1 to it. 12 R/WC 0b Received Completion Abort Status (RCAS): This bit is set when the (G)MCH generates a DMI request that receives a completion abort. Software clears this bit by writing a 1 to it. 11 RO 0b Signaled Target Abort Status (STAS): The (G)MCH will not generate a Target Abort DMI completion packet or Special Cycle. This bit is not implemented in the (G)MCH and is hardwired to a 0. Writes to this bit position have no effect. 10:9 RO 00b DEVSEL Timing (DEVT): These bits are hardwired to "00". Writes to these bit positions have no affect. Device 0 does not physically connect to PCI_A. These bits are set to 00 (fast decode) so that optimum DEVSEL timing for PCI_A is not limited by the (G)MCH. 8 RO 0b Master Data Parity Error Detected (DPD): PERR signaling and messaging are not implemented by the (G)MCH therefore this bit is hardwired to 0. Writes to this bit position have no effect. 7 RO 1b Fast Back-to-Back (FB2B): This bit is hardwired to 1. Writes to these bit positions have no effect. Device 0 does not physically connect to PCI_A. This bit is set to 1 (indicating fast back-to-back capability) so that the optimum setting for PCI_A is not limited by the (G)MCH. 6:5 186 RO 00b Reserved Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) Bit Access Default Value 4 RO 1b Description Capability List (CLIST): This bit is hardwired to 1 to indicate to the configuration software that this Device/Function implements a list of new capabilities. A list of new capabilities is accessed via register CAPPTR at configuration address offset 34h. Register CAPPTR contains an offset pointing to the start address within configuration space of this device where the AGP Capability standard register resides. 3:0 18.1.5 RO 0h Reserved RID - Revision Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 8h 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Revision Identification Number (RID): This is an 8-bit value that indicates the revision identification number for the (G)MCH. A register swapping mechanism behind RID register is used to select between a single SRID, or a single CRID to be reflected in the RID register. For the C0 stepping SRID= 03h, CRID= 0Ch. Datasheet 187 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.6 CC - Class Code B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 9-Bh 060000h RO 24 bits Bit Access Default Value 23:16 RO 06h Description Base Class Code (BCC): This is an 8-bit value that indicates the base class code for the (G)MCH. This code has the value 06h, indicating a bridge device. 15:8 RO 00h Sub-Class Code (SUBCC): This is an 8-bit value that indicates the category of bridge into which the (G)MCH falls. The code is 00h indicating a host bridge. 7:0 RO 00h Programming Interface (PI): This is an 8-bit value that indicates the programming interface of this device. This value does not specify a particular register set layout and provides no practical use for this device. 18.1.7 MLT - Master Latency Timer B/D/F/Type: Address Offset: Default Value: Access: Size: 188 0/0/0/PCI Dh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Reserved Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.8 HDR - Header Type B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI Eh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description PCI Header (HDR): This field always returns 0 to indicate that the (G)MCH is a single function device with standard header layout. Reads and writes to this location have no effect. 18.1.9 SVID - Subsystem Vendor Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 2C-2Dh 0000h R/WO 16 bits Bit Access Default Value 15:0 R/WO 0000h Description Subsystem Vendor ID (SUBVID): This field should be programmed during boot-up to indicate the vendor of the system board. After it has been written once, it becomes read only. 18.1.10 SID - Subsystem Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 2E-2Fh 0000h R/WO 16 bits Bit Access Default Value 15:0 R/WO 0000h Description Subsystem ID (SUBID): This field should be programmed during BIOS initialization. After it has been written once, it becomes read only. Datasheet 189 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.11 CAPPTR - Capabilities Pointer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 34h E0h RO 8 bits Bit Access Default Value 7:0 RO E0h Description Pointer to the Offset of the First Capability ID Register Block: In this case the first capability is the product-specific Capability Identifier (CAPID0). 18.1.12 EPBAR - Egress Port Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 40-47h 0000000000000000h R/W/L; RO; R/W 64 bits This is the base address for the Egress Port Root Complex MMIO configuration space. This window of addresses contains the Egress Port Root Complex Register set for the PCI Express Hierarchy associated with the (G)MCH. There is no physical memory within this 4-KB window that can be addressed. The 4 KB reserved by this register does not alias to any PCI 2.2-compliant memory mapped space. On reset, this register is disabled and must be enabled by writing a 1 to EPBAREN [bit 0 of this register]. Bit Access Default Value 63:36 R/W 0000000h 35:12 R/W/L 000000h Description Reserved Egress Port RCRB Base Address: This field corresponds to bits 35 to 12 of the base address Egress port RCRB MMIO configuration space. BIOS will program this register resulting in a base address for a 4-KB block of contiguous memory address space. This register ensures that a naturally aligned 4-KB space is allocated within total addressable memory space of 4 GB. System Software uses this base address to program the Egress Port RCRB and associated registers. 11:1 RO 000h 0 R/W/L 0b Reserved EPBAR Enable (EPBAREN): 0: EPBAR is disabled and does not claim memory. 1: EPBAR memory mapped accesses are claimed and decoded appropriately. 190 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.13 MCHBAR - (G)MCH Memory Mapped Register Range Base B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 48-4Fh 0000000000000000h R/W/L; RO; R/W 64 bits This is the base address for the (G)MCH MMIO Configuration space. There is no physical memory within this 16-KB window that can be addressed. The 16 KB reserved by this register does not alias to any PCI 2.2 compliant memory mapped space. On reset, this register is disabled and must be enabled by writing a 1 to MCHBAREN [Dev 0, offset 54h, bit 28]. 140h to 15Fh: Channel 0 System Memory Throttling. 1C0h to 1DFh: Channel 1 System Memory Throttling. C80h to CEFh: Thermal Sensor Control. F30h to F4Fh: PCI Express Throttling Control. Bit Access Default Value 63:36 R/W 0000000h 35:14 R/W/L 000000h Description Reserved (G)MCH Memory Map Base Address: This field corresponds to bits 35 to 14 of the base address MCHBAR configuration space. BIOS will program this register resulting in a base address for a 16-KB block of contiguous memory address space. This register ensures that a naturally aligned 16-KB space is allocated within total addressable memory space of 4 GB. System Software uses this base address to program the (G)MCH register set. 13:1 RO 0000h 0 R/W/L 0b Reserved MCHBAR Enable (MCHBAREN): 0: MCHBAR is disabled and does not claim any memory. 1: MCHBAR memory mapped accesses are claimed and decoded appropriately. Datasheet 191 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.14 GGC - (G)MCH Graphics Control Register (Device 0) B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 52-53h 0030h RO; R/W/L 16 bits Bit Access Default Value 15:7 RO 00000000 0b 6:4 R/W/L 011b Description Reserved Graphics Mode Select (GMS): This field is used to select the amount of Main Memory that is preallocated to support the Internal Graphics device in VGA (nonlinear) and Native (linear) modes. The BIOS ensures that memory is pre-allocated only when Internal graphics is enabled. Stolen Memory Bases is located between (TOLUD - SMSize) to TOUD. 000 = No memory pre-allocated. Device 2 (IGD) does not claim VGA cycles (Mem and IO), and the Sub-Class Code field within Device 2 Function 0. Class Code register is 80. 001 = DVMT (UMA) mode, 1 MB of memory pre-allocated for frame buffer. 010 = DVMT (UMA) mode, 4 MB of memory pre-allocated for frame buffer. 011 = DVMT (UMA) mode, 8 MB of memory pre-allocated for frame buffer. 100 = DVMT (UMA) mode, 16 MB of memory pre-allocated for frame buffer. 101 = DVMT (UMA) mode, 32 MB of memory pre-allocated for frame buffer. 110 = DVMT (UMA) mode, 48 MB of memory pre-allocated for frame buffer. 111 = DVMT (UMA) mode, 64 MB of memory pre-allocated for frame buffer. NOTE: This register is locked and becomes Read Only when the D_LCK bit in the SMRAM register is set. Hardware does not clear or set any of these bits automatically based on IGD being disabled/enabled. 3:2 RO 00b 1 R/W/L 0b Reserved IGD VGA Disable (IVD): 0: Enable (Default). Device 2 (IGD) claims VGA memory and IO cycles, the Sub-Class Code within Device 2 Class Code register is 00. 1: Disable. Device 2 (IGD) does not claim VGA cycles (Mem and IO), and the Sub-Class Code field within Device 2 Function 0 Class Code register is 80. 0 192 RO 0b Reserved Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.15 DEVEN - Device Enable B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 54-57h 000043DBh RO; R/W/L 32 bits Bit Access Default Value Description 31:10 RO 0000h Reserved 9:6 R/W/L 1b Reserved 5 RO 0b Reserved 4 R/W/L 1b Internal Graphics Engine Function 1 (D2F1EN): 0: Bus 0 Device 2 Function 1 is disabled and hidden 1: Bus 0 Device 2 Function 1 is enabled and visible. If Device 2 Function 0 is disabled and hidden, then Device 2 Function 1 is also disabled and hidden independent of the state of this bit. 3 R/W/L 1b Internal Graphics Engine Function 0 (D2F0EN): 0: Bus 0 Device 2 Function 0 is disabled and hidden. 1: Bus 0 Device 2 Function 0 is enabled and visible. If this (G)MCH does not have internal graphics capability (CAPID0[33] = 1) then Device 2 Function 0 is disabled and hidden independent of the state of this bit. 2 RO 0b Reserved 1 R/W/L 1b PCI Express Graphics Port Enable (D1EN): 0: Bus 0 Device 1 Function 0 is disabled and hidden. Also gates PCI Express internal clock (lgclk) and asserts PCI Express internal reset (lgrstB). 1: Bus 0 Device 1 Function 0 is enabled and visible. Default value is determined by the device capabilities (CAPID0[32] and CAPID0[77] ), SDVO presence HW strap and SDVO/PCIe concurrent HW strap.. 0 RO 1b Host Bridge: Bus 0 Device 0 Function 0 may not be disabled and is therefore hardwired to 1. Datasheet 193 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.16 PCIEXBAR - PCI Express Register Range Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 60-67h 00000000E0000000h R/W/L; RO; R/W 64 bits This is the base address for the PCI Express configuration space. This window of addresses contains the 4 KB of configuration space for each PCI Express device that can potentially be part of the PCI Express Hierarchy associated with the (G)MCH. There is not actual physical memory within this 256-MB window that can be addressed. Each PCI Express Hierarchies requires a PCI Express BASE register. The (G)MCH supports one PCI Express hierarchy. On reset, this register is disabled and must be enabled by writing a 1 to PCIEXBAREN [Dev 0, offset 54h, bit 31]. If the PCI Express Base Address [bits 35:28] were set to Fh, an overlap with the High BIOS area, APIC would result. Software must ensure that these ranges do not overlap. The PCI Express Base Address cannot be less than the maximum address written to the Top of physical memory register (TOLUD). If a system is populated with more than 3.5 GB, either the PCI Express Enhanced Access mechanism must be disabled or the value in TOLUD must be reduced to report that only 3.5 GB are present in the system to allow a value of Eh for the PCI Express Base Address (assuming that all PCI 2.3-compatible configuration space fits above 3.75 GB). Bit Access Default Value 63:36 R/W 0000000h 35:28 R/W/L 00001110b Description Reserved PCI Express Base Address: This field corresponds to bits 35 to 28 of the base address for PCI Express enhanced configuration space. BIOS will program this register resulting in a base address for a contiguous memory address space; size is defined by bits 3:1 of this register. This base address shall be assigned on a boundary consistent with the number of buses (defined by the Length field in this register), above TOLUD and still within total 36bit addressable memory space. The address bits decoded depend on the length of the region defined by this register. The address used to access the PCI Express configuration space for a specific device can be determined as follows : PCI Express Base Address + Bus Number * 1 MB + Device Number * 32 KB + Function Number * 4 KB The address used to access the PCI Express configuration space for Device 1 in this component would be PCI Express Base Address + 0 * 1 MB + 1 * 32 KB + 0 * 4 KB = PCI Express Base Address + 32 KB. Remember that this address is the beginning of the 4-KB space that contains both the PCI-compatible configuration space and the PCI Express extended configuration space. 194 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) Bit Access Default Value 27 R/W/L 0b Description 128-MB Address Mask: This bit is either part of the PCI Express Base Address (R/W) or part of the Address Mask (RO, read 0b), depending on the value of bits 2:1 in this register. 26 R/W/L 0b 64-MB Base Address Mask: This bit is either part of the PCI Express Base Address (R/W) or part of the Address Mask (RO, read 0b), depending on the value of bits 2:1 in this register. 25:3 RO 000000h 2:1 R/W/L 00b Reserved Length: This field describes the length of this region - Enhanced Configuration Space Region/Buses Decoded 00: 256 MB (Buses 0-255). Bits 31:28 are decoded in the PCI Express Base Address field. 01: 128 MB (Buses 0-127). Bits 31:27 are decoded in the PCI Express Base Address field. 10: 64 MB (Buses 0-63). Bits 31:26 are decoded in the PCI Express Base Address field. 11: Reserved 0 R/W/L 0b PCIEXBAR Enable (PCIEXBAREN): 0: PCIEXBAR register is disabled. Memory read and write transactions proceed as if there were no PCIEXBAR register. PCIEXBAR register bits 31:28 are R/W with no functionality behind them. 1: The PCIEXBAR register is enabled. Memory read and write transactions whose address bits 31:28 match PCIEXBAR 31:28 will be translated to configuration reads and writes within the (G)MCH. Datasheet 195 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.17 DMIBAR - MCH-ICH Serial Interconnect Ingress Root Complex B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 68-6Fh 0000000000000000h R/W; R/W/L; RO 64 bits This is the base address for the DMI Root Complex MMIO configuration space. This window of addresses contains the DMI Root Complex Register set for the PCI Express Hierarchy associated with the (G)MCH. There is no physical memory within this 4-KB window that can be addressed. The 4 KB reserved by this register does not alias to any PCI 2.2 compliant memory mapped space. On reset, this register is disabled and must be enabled by writing a 1 to RCBAREN [Dev 0, offset 54h, bit 29] Bit Access Default Value 63:36 R/W 0000000h 35:12 R/W/L 000000h Description Reserved DMI Root Complex MMIO Register Set Base Address: This field corresponds to bits 35 to 12 of the base address DMI RCRB MMIO configuration space. BIOS will program this register resulting in a base address for a 4-KB block of contiguous memory address space. This register ensures that a naturally aligned 4-KB space is allocated within total addressable memory space of 4 GB. System Software uses this base address to program the DMI RCRB registers. 11:1 RO 000h 0 R/W/L 0b Reserved DMIBAR Enable (DMIBAREN): 0: DMIBAR is disabled and does not claim any memory. 1: DMIBAR memory mapped accesses are claimed and decoded appropriately. 196 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.18 PMIOBAR - PM I/O BAR Register Definition B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 78-7Bh 00000000h R/W; RO 32 bits Bit Access Default Value 31:16 RO 0000h 15:6 R/W 000h Description Reserved Base Address: Base address of the PM I/O Space. 5:1 RO 00h 0 R/W 0b Reserved PM I/O BAR Enable: BIOS should enable this bit after the base address for the PM I/O Bar is decided and allocated. This enable can be programmed while the Base Address is programmed. HOST Cluster should not positively decode level reads to PM I/O BAR base unless the space is enabled. Datasheet 197 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.19 PAM0 - Programmable Attribute Map 0 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 90h 00h RO; R/W/L 8 bits This register controls the read, write, and shadowing attributes of the BIOS area from 0F0000h-0FFFFFh. The (G)MCH allows programmable memory attributes on 13 Legacy memory segments of various sizes in the 640-KB to 1-MB address range. Seven Programmable Attribute Map (PAM) Registers are used to support these features. Cacheability of these areas is controlled via the MTRR registers in the P6 processor. Two bits are used to specify memory attributes for each memory segment. These bits apply to both host accesses and PCI initiator accesses to the PAM areas. These attributes are: RE - Read Enable. When RE = 1, the CPU read accesses to the corresponding memory segment are claimed by the (G)MCH and directed to main memory. Conversely, when RE = 0, the host read accesses are directed to PCI_A. WE - Write Enable. When WE = 1, the host write accesses to the corresponding memory segment are claimed by the (G)MCH and directed to main memory. Conversely, when WE = 0, the host write accesses are directed to PCI_A. The RE and WE attributes permit a memory segment to be Read Only, Write Only, Read/Write, or disabled. For example, if a memory segment has RE = 1 and WE = 0, the segment is Read Only. Each PAM Register controls two regions, typically 16 KB in size. Accesses to the entire PAM region (000C_0000h to 000F_FFFFh) from DMI and PCI Express Graphics Attach low priority will be forwarded to main memory. The PAM read enable and write enable bits are not functional for these accesses. In other words, a full set of PAM decode/attribute logic is not being implemented. Also note that the (G)MCH may hang if a PCI Express Graphics Attach or DMI originated access to Read Disabled or Write Disabled PAM segments occur (due to a possible IWB to non-DRAM). For these reasons the following critical restriction is placed on the programming of the PAM regions: At the time that a DMI or PCI Express Graphics Attach accesses to the PAM region may occur, the targeted PAM segment must be programmed to be both readable and writeable. 198 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) Bit Access Default Value Description 7:6 RO 00b Reserved 5:4 R/W/L 00b 0F0000-0FFFFF Attribute (HIENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0F0000 to 0FFFFF. 00: DRAM Disabled: All accesses are directed to DMI. 01: Read Only: All reads are sent to DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. 3:0 Datasheet RO 0h Reserved 199 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.20 PAM1 - Programmable Attribute Map 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 91h 00h RO; R/W/L 8 bits This register controls the read, write, and shadowing attributes of the BIOS areas from 0C0000h-0C7FFFh. Bit Access Default Value Description 7:6 RO 00b Reserved 5:4 R/W/L 00b 0C4000-0C7FFF Attribute (HIENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0C4000 to 0C7FFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. 3:2 RO 00b Reserved 1:0 R/W/L 00b 0C0000-0C3FFF Attribute (LOENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0C0000 to 0C3FFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. 200 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.21 PAM2 - Programmable Attribute Map 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 92h 00h RO; R/W/L 8 bits This register controls the read, write, and shadowing attributes of the BIOS areas from 0C8000h-0CFFFFh. Bit Access Default Value Description 7:6 RO 00b Reserved 5:4 R/W/L 00b 0CC000-0CFFFF Attribute (HIENABLE): Reserved 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. 3:2 RO 00b Reserved 1:0 R/W/L 00b 0C8000-0CBFFF Attribute (LOENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0C8000 to 0CBFFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. Datasheet 201 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.22 PAM3 - Programmable Attribute Map 3 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 93h 00h RO; R/W/L 8 bits This register controls the read, write, and shadowing attributes of the BIOS areas from 0D0000h-0D7FFFh. Bit Access Default Value Description 7:6 RO 00b Reserved 5:4 R/W/L 00b 0D4000-0D7FFF Attribute (HIENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0D4000 to 0D7FFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. 3:2 RO 00b Reserved 1:0 R/W/L 00b 0D0000-0D3FFF Attribute (LOENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0D0000 to 0D3FFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. 202 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.23 PAM4 - Programmable Attribute Map 4 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 94h 00h RO; R/W/L 8 bits This register controls the read, write, and shadowing attributes of the BIOS areas from 0D8000h-0DFFFFh. Bit Access Default Value Description 7:6 RO 00b Reserved 5:4 R/W/L 00b 0DC000-0DFFFF Attribute (HIENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0DC000 to 0DFFFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. 3:2 RO 00b Reserved 1:0 R/W/L 00b 0D8000-0DBFFF Attribute (LOENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0D8000 to 0DBFFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. Datasheet 203 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.24 PAM5 - Programmable Attribute Map 5 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 95h 00h RO; R/W/L 8 bits Bit Access Default Value Description 7:6 RO 00b Reserved 5:4 R/W/L 00b 0E4000-0E7FFF Attribute (HIENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0E4000 to 0E7FFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. 3:2 RO 00b Reserved 1:0 R/W/L 00b 0E0000-0E3FFF Attribute (LOENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0E0000 to 0E3FFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. 204 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.25 PAM6 - Programmable Attribute Map 6 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 96h 00h RO; R/W/L 8 bits This register controls the read, write, and shadowing attributes of the BIOS areas from 0E8000h-0EFFFFh. Bit Access Default Value Description 7:6 RO 00b Reserved 5:4 R/W/L 00b 0EC000-0EFFFF Attribute (HIENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0EC000 to 0EFFFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. 3:2 RO 00b Reserved 1:0 R/W/L 00b 0E8000-0EBFFF Attribute (LOENABLE): This field controls the steering of read and write cycles that address the BIOS area from 0E8000 to 0EBFFF. 00: DRAM Disabled: Accesses are directed to DMI. 01: Read Only: All reads are serviced by DRAM. All writes are forwarded to DMI. 10: Write Only: All writes are sent to DRAM. Reads are serviced by DMI. 11: Normal DRAM Operation: All reads and writes are serviced by DRAM. Datasheet 205 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.26 LAC - Legacy Access Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 97h 00h R/W/L; RO 8 bits This 8-bit register controls a fixed DRAM hole from 15-16 MB. Bit Access Default Value 7 R/W/L 0b Description Hole Enable (HEN): This field enables a memory hole in DRAM space. The DRAM that lies "behind" this space is not remapped. 0: No memory hole. 1: Memory hole from 15 MB to 16 MB. 6:1 RO 00h 0 R/W/L 0b Reserved MDA Present (MDAP): This bit works with the VGA Enable bits in the BCTRL register of Device 1 to control the routing of CPU initiated transactions targeting MDA compatible I/O and memory address ranges. This bit should not be set if Device 1's VGA Enable bit is not set. If Device 1's VGA enable bit is not set, then accesses to IO address range x3BCh-x3BFh are forwarded to DMI. If the VGA enable bit is set and MDA is not present, then accesses to IO address range x3BCh-x3BFh are forwarded to PCI Express-G if the address is within the corresponding IOBASE and IOLIMIT, otherwise they are forwarded to DMI. MDA resources are defined as the following: Memory: 0B0000h - 0B7FFFh I/O:3B4h, 3B5h, 3B8h, 3B9h, 3BAh, 3BFh (including ISA address aliases, A[15:10] are not used in decode). Any I/O reference that includes the I/O locations listed above, or their aliases, will be forwarded to DMI even if the reference includes I/O locations not listed above. The following table shows the behavior for all combinations of MDA and VGA: VGAEN 0 206 MDAP 0 0 1 1 0 1 1 Description All references to MDA and VGA space are routed to HI Illegal Combination All VGA and MDA references are routed to PCI Express Graphics Attach All VGA references are routed to PCI Express Graphics Attach. MDA references are routed to HI. Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.27 REMAPBASE - Remap Base Address Register B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 98-99h 03FFh RO; R/W/L 16 bits Bit Access Default Value Description 15:10 RO 00h Reserved 9:0 R/W/L 3FFh Remap Base Address[35:26]: The value in this register defines the lower boundary of the Remap window. The Remap window is inclusive of this address. In the decoder A[25:0] of the Remap Base Address are assumed to be 0's. Thus the bottom of the defined memory range will be aligned to a 64-MB boundary. When the value in this register is greater than the value programmed into the Remap Limit register, the Remap window is disabled. This field defaults to 3FFh. NOTE: Bit 0 (Address Bit 26) must be a 0 18.1.28 REMAPLIMIT - Remap Limit Address Register B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 9A-9Bh 0000h RO; R/W/L 16 bits Bit Access Default Value 15:10 RO 00h 9:0 R/W/L 000h Description Reserved Remap Limit Address [35:26]: The value in this register defines the upper boundary of the Remap window. The Remap window is inclusive of this address. In the decoder A[25:0] of the Remap Limit Address are assumed to be F's. Thus the top of the defined range will be one less than a 64-MB boundary. When the value in this register is less than the value programmed into the Remap Base register, the Remap window is disabled. This field defaults to 00h. NOTE: Bit 0 (Address Bit 26) must be a 0. Datasheet 207 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.29 SMRAM - System Management RAM Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 9Dh 02h RO; R/W/L; R/W 8 bits The SMRAMC register controls how accesses to Compatible and Extended SMRAM spaces are treated. The Open, Close, and Lock bits function only when G_SMRAME bit is set to a 1. Also, the OPEN bit must be reset before the LOCK bit is set. Bit Access Default Value Description 7 RO 0b Reserved 6 R/W/L 0b SMM Space Open (D_OPEN): (When D_OPEN=1 and D_LCK=0, the SMM space DRAM is made visible even when SMM decode is not active. This is intended to help BIOS initialize SMM space. Software should ensure that D_OPEN=1 and D_CLS=1 are not set at the same time. 5 R/W 0b SMM Space Closed (D_CLS): When D_CLS = 1 SMM space DRAM is not accessible to data references, even if SMM decode is active. Code references may still access SMM space DRAM. This will allow SMM software to reference through SMM space to update the display even when SMM is mapped over the VGA range. Software should ensure that D_OPEN=1 and D_CLS=1 are not set at the same time. Note that the D_CLS bit only applies to Compatible SMM space. 4 R/W/L 0b SMM Space Locked (D_LCK): When D_LCK is set to a 1 then D_OPEN is reset to 0 and D_LCK, D_OPEN, G_SMRARE, C_BASE_SEG, H_SMRAM_EN, GMS, TOLUD, TOM, TSEG_SZ, and TSEG_EN become read only. D_LCK can be set to 1 via a normal configuration space write but can only be cleared by a Full Reset. The combination of D_LCK and D_OPEN provide convenience with security. The BIOS can use the D_OPEN function to initialize SMM space and then use D_LCK to "lock down" SMM space in the future so that no application software (or BIOS itself) can violate the integrity of SMM space, even if the program has knowledge of the D_OPEN function. 3 R/W/L 0b Global SMRAM Enable (G_SMRARE): If set to a 1, then Compatible SMRAM functions are enabled, providing 128 KB of DRAM accessible at the A0000h address while in SMM (ADSB with SMM decode). To enable Extended SMRAM function this bit has be set to 1. Refer to the section on SMM for more details. Once D_LCK is set, this bit becomes read only. 208 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) Bit Access Default Value 2:0 RO 010b Description Compatible SMM Space Base Segment (C_BASE_SEG): This field indicates the location of SMM space. SMM DRAM is not remapped. It is simply made visible if the conditions are right to access SMM space, otherwise the access is forwarded to DMI. Since the (G)MCH supports only the SMM space between A0000 and BFFFF, this field is hardwired to 010. 18.1.30 ESMRAMC - Extended System Management RAM Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI 9Eh 38h R/W/L; R/WC; RO 8 bits Bit Access Default Value 7 R/W/L 0b Description Enable High SMRAM (H_SMRAME): Controls the SMM memory space location (i.e., above 1 MB or below 1 MB) When G_SMRAME is 1 and H_SMRAME this bit is set to 1, the high SMRAM memory space is enabled. SMRAM accesses within the range 0FEDA0000h to 0FEDBFFFFh are remapped to DRAM addresses within the range 000A0000h to 000BFFFFh. Once D_LCK has been set, this bit becomes read only. 6 R/WC 0b Invalid SMRAM Access (E_SMERR): This bit is set when CPU has accessed the defined memory ranges in Extended SMRAM (High Memory and T-segment) while not in SMM space and with the D-OPEN bit = 0. It is software's responsibility to clear this bit. The software must write a 1 to this bit to clear it. 5 RO 1b SMRAM Cacheable (SM_CACHE): This bit is forced to 1 by the (G)MCH . 4 RO 1b L1 Cache Enable for SMRAM (SM_L1): This bit is forced to 1 by the (G)MCH. 3 RO 1b L2 Cache Enable for SMRAM (SM_L2): This bit is forced to 1 by the (G)MCH. Datasheet 209 Host Bridge Device 0 Configuration Registers (D0:F0) Bit Access Default Value 2:1 R/W/L 00b Description TSEG Size (TSEG_SZ): Selects the size of the TSEG memory block if enabled. Memory from the top of DRAM space is partitioned away so that it may only be accessed by the processor interface and only then when the SMM bit is set in the request packet. Non-SMM accesses to this memory region are sent to DMI when the TSEG memory block is enabled. 00: 1-MB Tseg. (TOLUD: Graphics Stolen Memory Size - 1M) to (TOLUD - Graphics Stolen Memory Size). 01: 2-MB Tseg (TOLUD: Graphics Stolen Memory Size - 2M) to (TOLUD - Graphics Stolen Memory Size). 10: 8-MB Tseg (TOLUD: Graphics Stolen Memory Size - 8M) to (TOLUD - Graphics Stolen Memory Size). 11: Reserved Once D_LCK has been set, these bits become read only. 0 R/W/L 0b TSEG Enable (T_EN): Enabling of SMRAM memory for Extended SMRAM space only. When G_SMRAME =1 and TSEG_EN = 1, the TSEG is enabled to appear in the appropriate physical address space. Note that once D_LCK is set, this bit becomes read only. 18.1.31 TOM - Top of Memory B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI A0-A1h 0001h RO; R/W/L 16 bits This register contains the size of physical memory. BIOS determine the memory size reported to the OS using this register. Bit Access Default Value 15:9 RO 00h 8:0 R/W/L 001h Description Reserved Top of Memory: This register reflects the total amount of populated physical memory. This is also the amount of addressable physical memory when remapping is used appropriate to ensure that no physical memory is wasted. This is NOT necessarily the highest main memory address (holes may exist in main memory address map due to addresses allocated for memory mapped IO). These bits correspond to address bits 35:27 (128-MB granularity). Bits 26:0 are assumed to be 0. 210 Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.32 TOUUD - Top of Upper Usable DRAM B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI A2-A3h 0000h R/W/L 16 bits Configuration software must set this value to TOM minus all Manageability Engine stolen memory if reclaim is disabled. If reclaim is enabled, this value must be set to reclaim limit 64-MB aligned since reclaim limit is 64-MB aligned. Address bits 19:0 are assumed to be 0_0000h for the purposes of address comparison. The Host interface positively decodes an address towards DRAM if the incoming address is less than the value programmed in this register and greater than or equal to 4 GB. Bit Access Default Value 15:0 R/W/L 0000h Description Top of Upper Usable DRAM (TOUUD): This register contains bits 35 to 20 of an address one byte above the maximum DRAM memory above 4 GB that is usable by the operating system. Configuration software must set this value to TOM minus all Manageability Engine stolen memory if reclaim is disabled. If reclaim is enabled, this value must be set to reclaim limit 64-MB aligned since reclaim limit is 64-MB aligned. Address bits 19:0 are assumed to be 0_0000h for the purposes of address comparison. The Host interface positively decodes an address towards DRAM if the incoming address is less than the value programmed in this register and greater than 4 GB. Datasheet 211 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.33 TOLUD - Top of Low Used DRAM Register B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI B0-B1h 0010h R/W/L; RO 16 bits This 16 bit register defines the Top of Low Usable DRAM. Graphics Stolen Memory and TSEG are within dram space defined under TOLUD. From the Top of Low Usable DRAM, (G)MCH claims 1 to 64 MBs of DRAM for internal graphics if enabled and 1, 2 or 8 MBs of DRAM for TSEG if enabled. Note: Even if the OS does not need any PCI space, TOLUD can only be programmed to FFh. This ensures that addresses within 128 MB below 4 GB that are reserved for APIC Bit Access Default Value 15:4 R/W/L 001h Description Top of Low Usable DRAM (TOLUD): This register contains bits 31 to 20 of an address one byte above the maximum DRAM memory below 4 G that is usable by the operating system. Address bits 31 down to 20 programmed to a "001h" implies a minimum memory size of 1 M. Configuration software must set this value to the smaller of the following 2 choices : - maximum amount memory in the system minus Intel(R) Management Engine stolen memory plus 1 byte or - the minimum address allocated for PCI memory. Address bits 19:0 are assumed to be 0_0000h for the purposes of address comparison. The Host interface positively decodes an address towards DRAM if the incoming address is less than that value programmed in this register. This register must not be set to 00000h Note that the Top of Low Usable DRAM is the lowest address above both Graphics Stolen memory and TSEG. NOTE: This register must be 64-M aligned when reclaim is enabled. 3:0 212 RO 0h Reserved Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.34 ERRSTS - Error Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI C8-C9h 0000h RO; R/WC/S 16 bits Bit Access Default Value Description 15 RO 0b Reserved 14:13 R/WC/S 00b Reserved 12 R/WC/S 0b (G)MCH Software Generated Event for SMI: This indicates the source of the SMI was a Device 2 Software Event. 11 R/WC/S 0b (G)MCH Thermal Sensor Event for SMI/SCI/SERR: Indicates that a (G)MCH Thermal Sensor trip has occurred and an SMI, SCI or SERR has been generated. The status bit is set only if a message is sent based on Thermal event enables in Error command, SMI command and SCI command registers. A trip point can generate one of SMI, SCI, or SERR interrupts (two or more per event is illegal). Multiple trip points can generate the same interrupt, if software chooses this mode, subsequent trips may be lost. If this bit is already set, then an interrupt message will not be sent on a new thermal sensor event. 10 RO 0b Reserved 9 R/WC/S 0b LOCK to Non-DRAM Memory Flag (LCKF): When this bit is set to 1, the (G)MCH has detected a lock operation to memory space that did not map into DRAM. 8 R/WC/S 0b Received Refresh Timeout Flag (RRTOF): This bit is set when 1024 memory core refreshes are enqueued. 7 R/WC/S 0b DRAM Throttle Flag (DTF): 0: Software has cleared this flag since the most recent throttling event. 1: Indicates that a DRAM Throttling condition occurred. 6:0 Datasheet RO 00h Reserved 213 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.35 ERRCMD - Error Command B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI CA-CBh 0000h RO; R/W 16 bits Bit Acces s Default Value Description 15:12 RO 0h Reserved 11 R/W 0b SERR on (G)MCH Thermal Sensor Event (TSESERR): 0: Reporting of this condition via SERR messaging is disabled. 1: The (G)MCH generates a SERR DMI special cycle when bit 11 of the ERRSTS is set. The SERR must not be enabled at the same time as the SMI for the same thermal sensor event. 10 RO 0b Reserved 9 R/W 0b SERR on LOCK to Non-DRAM Memory (LCKERR): 0: Reporting of this condition via SERR messaging is disabled. 1: The (G)MCH will generate a DMI SERR special cycle whenever a CPU lock cycle is detected that does not hit DRAM 8 R/W 0b SERR on DRAM Refresh Timeout (DRTOERR): 0: Reporting of this condition via SERR messaging is disabled. 1: The (G)MCH generates an SERR DMI special cycle when a DRAM Refresh timeout occurs. 7 R/W 0b SERR on DRAM Throttle Condition (DTCERR): 0: Reporting of this condition via SERR messaging is disabled. 1: The (G)MCH generates an SERR DMI special cycle when a DRAM Read or Write Throttle condition occurs. 6:0 214 RO 00h Reserved Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.36 SKPD - Scratchpad Data B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI DC-DFh 00000000h R/W 32 bits This register holds 32 writable bits with no functionality behind them. It is for the convenience of BIOS and graphics drivers. Bit Access Default Value 31:0 R/W 00000000h Description Scratchpad Data: 1 Dword of data storage. 18.1.37 CAPID0 - Capability Identifier B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI E0-E9h 000000000000010A0009h RO 80 bits Bit Access Default Value Description 79 RO 0b Reserved 78 RO 0b X4 DMI Link Width Capability Disable: 0: MCH - ICH Serial Interface is capable of X4 or X2 link widths. 1: MCH - ICH Serial Interface is a X2 link, not capable of X4. 77 RO 0b Concurrent PCI-E and SDVO Enable : Controls whether concurrent use of PCI-E Graphics Port and SDVO is allowed. 0: Concurrent PCIe and SDVO is not allowed. 1: Concurrent PCIe and SDVO is allowed. 76:62 RO 0000b Reserved 61:58 RO 0000b Compatibility Revision ID: This is an 8-bit value that indicates the revision identification number for the (G)MCH Device 0. For the A-0 Stepping, this value is 00h. 57:45 RO 0b 44:42 RO 000b Reserved GFX Software Capability ID Used to communicate Graphics SKU information to the Graphics Driver software, which can enable/disable certain features based on the product SKU. Datasheet 215 Host Bridge Device 0 Configuration Registers (D0:F0) Bit Access Default Value Description 41:37 RO 0b Reserved 36:35 RO 00b Reserved 34 RO 0b Serial Digital Video Out Enable: 0: (G)MCH Not capable of serial digital video output. 1: (G)MCH capable of serial digital video output. 33 RO 0b Internal Graphics Disable: 0: There is a graphics engine within this GMCH. Internal Graphics Device (Device 2) is enabled and all of its memory and I/O spaces are accessible. Configuration cycles to Device 2 will be completed within the GMCH. All non-SMM memory and IO accesses to VGA will be handled based on Memory and IO enables of Device 2 and IO registers within Device 2 and VGA Enable of the PCI to PCI bridge control register in Device 1 (If PCI Express GFX attach is supported). A selected amount of Graphics Memory space is pre-allocated from the main memory based on Graphics Mode Select (GMS in the GMCH Control Register). Graphics Memory is pre-allocated above TSEG Memory. 1: There is no graphics engine within this GMCH. Internal Graphics Device (Device 2) and all of its memory and I/O functions are disabled. Configuration cycle targeted to Device 2 will be passed on to DMI. In addition, All clocks to internal graphics logic are turned off. All non-SMM memory and IO accesses to VGA will be handled based on VGA Enable of the PCI to PCI bridge control register in Device 1. DEVEN [4:3] (Device 0, offset 54h) are forced to 00have no meaning. Device 2 Functions 0 and 1 are disabled and hidden. In addition, the memory decoding for LT trusted graphics registers at 0xFED305xx is also disabled. 32 RO 0b PCI Express Port Disable: 0: There is a PCI Express GFX Attach on this GMCH. Device 1 and associated memory spaces are accessible. All nonSMM memory and IO accesses to VGA will be handled based on VGA Enable of the PCI to PCI bridge control register in Device 1 and VGA settings controlling internal graphics VGA if internal graphics is enabled. 1: There is no PCI Express GFX Attach on this (G)MCH. Device 1 and associated memory and IO spaces are disabled. In addition, Next_Pointer = 00h, VGA memory and IO cannot decode to the PCI Express interface. VGA memory and IO cannot decode to the PCI Express interface. From a Physical Layer perspective, all 16 lanes are powered down and the link does not attempt to train. 31 216 RO 0b Reserved Datasheet Host Bridge Device 0 Configuration Registers (D0:F0) Bit Access Default Value 30 RO 0b Description DDR2 Frequency Capability: 0: (G)MCH capable of "All" memory frequencies (DDR2 667 MHz or lower). 1: (G)MCH capable of up to DDR2-533. This field controls which values may be written to the Memory Frequency Select field 6:4 of the Clocking Configuration Register (MCHBAR Offset C00h). Any attempt to write an unsupported value will be ignored. 29:28 RO 00b FSB Capability: These values are determined by the BSEL[2:0] frequency straps. Any unsupported straps will render the GMCH host interface inoperable. 01: (G)MCH capable of up to FSB 800 MHz. 10-11: (G)MCH capable of up to FSB 667 MHz. 27:24 RO 1h CAPID Version: This field has the value 0001b to identify the first revision of the CAPID register definition. 23:16 RO 0Ah CAPID Length: This field has the value 0Ah to indicate the structure length (10 bytes). 15:8 RO 00h Next Capability Pointer: This field is hardwired to 00h indicating the end of the capabilities linked list. 7:0 RO 09h CAP_ID: This field has the value 1001b to identify the CAP_ID assigned by the PCI SIG for vendor dependent capability pointers. Datasheet 217 Host Bridge Device 0 Configuration Registers (D0:F0) 18.1.38 CRLT - (G)MCH Dev0 Test B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/PCI F0h 00h RO; R/WO 8 bits Bit Access Default Value 7:1 RO 00h 0 R/WO 0b Description Reserved Intel(R) Management Engine Stolen Memory Lock (ME_SM_LOCK2): ME_SM_LOCK2 can be set to 1 via a normal configuration space write but can only be cleared by a Full Reset. BIOS will initialize config bits related to dram decode and then use ME_SM_LOCK2 to "lock down" the dram decode in the future so that no application software (or BIOS itself) can violate the integrity. 218 Datasheet Device 0 Memory Mapped I/O Register 19 Device 0 Memory Mapped I/O Register Note: All accesses to the Memory Mapped registers must be made as a single Dword (4 bytes) or less. Access must be aligned on a natural boundary. 19.1 Device 0 Memory Mapped I/O Registers A variety of timing and control registers have been moved to MMR space of Device 0 due to space constraints. To simplify the read/write logic to the SRAM, BIOS is required to write and read 32-bit aligned Double Words. The SRAM includes a separate Write Enable for every Double Word. The BIOS read/write cycles are performed in a memory mapped IO range that is setup for this purpose in the PCI configuration space, via standard PCI range scheme. 19.2 Device 0 MCHBAR Chipset Control Registers Register Name Register Symbol Reserved Register End 00 3F Default Value Access Front Side Bus Power Management Control 3 FSBPMC3 40 43 00000000h RO; R/W Front Side Bus Power Management Control 4 FSBPMC4 44 47 00000002h R/W FSB Snoop Control FSBSNPCTL 48 4B 80800000h RO; R/W 4C 8F Reserved CPU Sleep Timing Control SLPCTL 90 93 00005055h RO; R/W Front Side Bus Power Management Control 5 FSBPMC5 94 97 00010080h R/W 98 1FF Reserved Datasheet Register Start 219 Device 0 Memory Mapped I/O Register Register Name Register Symbol Register End Default Value Access DRAM Channel Control DCC 200 203 00000000h RO; R/W; R/W/L DRAM Channel Control 2 DCC2 204 207 00000000h RO; R/W/L 208 217 218 21B A4008000h RO; R/W 21C 21F Reserved Write Cache Control WCC Reserved Main Memory Arbiter Control_0 MMARB0 220 223 00000264h RO; R/W Main Memory Arbiter Control_1 MMARB1 224 227 00000000h RO; R/W 228 22F 230 233 340A0000h RO; R/W 234 2BF Reserved SB Test Register Reserved 19.2.1 Register Start SBTEST FSBPMC3 - Front Side Bus Power Management Control 3 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 40-43h 00000000h RO; R/W 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.2.2 FSBPMC4 - Front Side Bus Power Management Control 4 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 44-47h 00000002h R/W 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 220 Datasheet Device 0 Memory Mapped I/O Register 19.2.3 FSBSNPCTL - FSB Snoop Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 48-4Bh 80800000h RO; R/W 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.2.4 SLPCTL - CPU Sleep Timing Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 90-93h 00005055h RO; R/W 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.2.5 FSBPMC5 - Front Side Bus Power Management Control 5 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 94-97h 00010080h R/W 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.2.6 DCC - DRAM Channel Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 200-203h 00000000h RO; R/W; R/W/L 32 bits This register controls how the DRAM channels work together. It affects how the CxDRB registers are interpreted and allows them to steer transactions to the correct channel. Datasheet Bit Access Default Value Description 31:29 RO 000b Reserved 28:24 R/W 00h Reserved 23 RO 0b Reserved 221 Device 0 Memory Mapped I/O Register Bit Access Default Value 22:21 R/W 00b Description Select for EMRS Commands: This field applies only when the Mode Select (SMS) bits = 100, implying an EMRS command. 00: Bank 1 (BS[2:0] = 001), EMRS(1) 01: Bank 2 (BS[2:0] = 010), EMRS(2) 10: Bank 3 (BS[2:0] = 011), EMRS(3) 11: Reserved 20 R/W 0b Independent Dual Channel IC/SMS Enable: 0: IC and SMS controls in DCC register control both system memory channels. 1: IC and SMS bits in C0/1DRC0 register control each system memory channel independently. 19 R/W 0b Initialization Complete (IC): See register description in C0DRC0[29]. 18:16 R/W 000b Mode Select (SMS): See register description in C0DRC0[6:4]. 15 R/W 0b Reserved 14:11 RO 0000b Reserved 10 R/W/L 0b Channel XOR Disable (CXRDIS): 0: Channel XOR Randomization is enabled. 1: Channel XOR Randomization is disabled. 9 R/W/L 0b Reserved 8:2 RO 0000000b Reserved 1 R/W/L 0b DRAM Addressing Mode Control (DAMC): 0: Single Channel/Dual Channel Asymmetric. 1: Dual Channel symmetric. 0 222 RO 0b Reserved Datasheet Device 0 Memory Mapped I/O Register 19.2.7 DCC2 - DRAM Channel Control 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 204-207h 00000000h RO; R/W/L 32 bits Bit Access Default Value Description 31:16 RO 0000h Reserved 15:0 R/W/L 0000h Intel(R) Management Engine Size (MESZ): This register indicates total memory which is mapped to MEUMA(Sx) region operation ( 1-MB Granularity). 19.2.8 WCC - Write Cache Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 218-21Bh A4008000h RO; R/W 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.2.9 MMARB0 - Main Memory Arbiter Control_0 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 220-223h 00000264h RO; R/W 32 bits 0h This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.2.10 MMARB1 - Main Memory Arbiter Control_1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 224-227h 00000000h RO; R/W 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. Datasheet 223 Device 0 Memory Mapped I/O Register 19.2.11 SBTEST - SB Test Register B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR Chipset 230-233h 340A0000h RO; R/W 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.3 Device 0 MCHBAR Clock Controls Register Name Clocking Configuration Register Symbol CLKCFG Reserved Register End C00 C03 C04 C13 Default Value Access 00000200h RO; R/W Unit Power Management Control 1 UPMC1 C14 C15 0223h RO; R/W CPunit Control CPCTL C16 C17 00A0h RO; R/W C18 C1B C1C C1D 0000h R/W/S C1E C1F C20 C21 0001h RO; R/W C22 C33 Reserved Sticky Scratchpad Data SSKPD Reserved Unit Power Management Control 2 UPMC2 Reserved Host-Graphics Interface Power Management Control 1 HGIPMC1 C34 C37 00000000h R/W Host-Graphics Interface Power Management Control 2 HGIPMC2 C38 C3B 00000000h R/W C3C C67 Reserved 224 Register Start Datasheet Device 0 Memory Mapped I/O Register 19.3.1 CLKCFG - Clocking Configuration B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR C00-C03h 00000200h RO; R/W 32 bits Bit Access Default Value Description 31 R/W 0b Reserved 30:28 RO 000b Reserved 27:15 R/W 0000h Reserved 14 R/W 0b HW Dynamic FSB Frequency Switching Enable: 0: OFF 1: ON 7 R/W 0b VHCLK Polarity in Half-mode (VHCLK_polarity): Dynamic FSB Frequency Switching vhclk inversion in 1/2frequency mode. 0: Do not invert polarity 1: Invert vhclk polarity when entering 1/2-frequency mode 6:4 RO 000b Memory Frequency Select: The clock config straps, update the default value of this register. 011: 533 100: 667 others: Reserved 3 R/W 0b 2:0 RO 000b Reserved FSB Frequency Select: Reflects the State of BSEL pins from the Processor. BSEL(2:0) selects the FSB frequency as defined below: 001: FSB533 011: FSB667 010: FSB800 Others: Reserved Attempts to strap values to unsupported frequencies will shut down the host PLL. Datasheet 225 Device 0 Memory Mapped I/O Register 19.3.2 UPMC1 - Unit Power Management Control 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR C14-C15h 0223h RO; R/W 16 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.3.3 CPCTL - CPunit Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR C16-C17h 00A0h RO; R/W 16 bits This register bit shall contain the default value unless otherwise indicated in the BIOS Specification. 19.3.4 SSKPD - Sticky Scratchpad Data B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR C1C-C1Dh 0000h R/W/S 16 bits This register holds 16 writable bits with no functionality behind them. It is for the convenience of BIOS and graphics drivers. This Register is reset on PWROK. Bit Access Default Value 15:0 R/W/S 0000h Description Scratchpad Data: 1 WORD of data storage. 19.3.5 UPMC2 - Unit Power Management Control 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR C20-C21h 0001h RO; R/W 16 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 226 Datasheet Device 0 Memory Mapped I/O Register 19.3.6 HGIPMC1 - Host-Graphics Interface Power Management Control 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR C34-C37h 00000000h RO; R/W 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.3.7 HGIPMC2 - Host-Graphics Interface Power Management Control 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR C38-C3Bh 00000000h RO; R/W 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.4 Device 0 MCHBAR ACPI Power Management Controls Register Name Register Symbol Register End Default Value Access C2 to C3 Transition Timer C2C3TT F00 F03 00000000h RO; R/W C3 to C4 Transition Timer C3C4TT F04 F07 00000000h RO; R/W F08 F0D F0E F0E 00h R/W F0F F13 F14 F17 00000000h R/WC; RO F18 FAF Reserved Memory Interface Power Management Control MIPMC Reserved Self-Refresh Channel Status Reserved Datasheet Register Start SLFRCS 227 Device 0 Memory Mapped I/O Register Register Name Register Symbol Graphics Interface Power Management Control 1 GIPMC1 Reserved Front Side Bus Power Management Control 1 FSBPMC1 Reserved Unit Power Management Control 3 UPMC3 Reserved 19.4.1 Register Start Register End FB0 FB0 FB1 FB7 FB8 FBB FBC FBF FC0 FC3 FFC FFF Default Value Access 00h RO; R/W 00h RO; R/W 00000000h RO; R/W C2C3TT - C2 to C3 Transition Timer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR F00-F03h 00000000h RO; R/W 32 bits Bit Access Default Value 31:19 RO 0000h 18:7 R/W 000h Description Reserved C2 to C3 Transition Timer (C2C3TT): Dual purpose timer in 128-core clock granularity. Number of core clocks to wait between last snoop from PEG or DMI to a Req_C3 DMI message being issued. Timer is activated only when the WAIT_C3 message from DMI has been received when in C2. 000 = 128 host clocks FFF = 524288 host clocks MSI's, for the purpose of this register, are handled as snoops. 6:0 228 RO 00h Reserved Datasheet Device 0 Memory Mapped I/O Register 19.4.2 C3C4TT - C3 to C4 Transition Timer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR F04-F07h 00000000h RO; R/W 32 bits Bit Access Default Value 31:19 RO 0000h 18:7 R/W 000h Description Reserved C3 to C4 Transition Timer (C34TT): 128-core clock granularity. Number of core clocks to wait between last snoop from PEG or DMI to a Req_C4 DMI message being issued. Timer is activated only when the WAIT_C4 message from DMI has been received when in C3. NOTES: 000 = 128 host clocks FFF = 524288 host clocks MSI's, for the purpose of this register, are handled as snoops. 6:0 19.4.3 RO 00h Reserved MIPMC - Memory Interface Power Management Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR F0Eh 00h R/W 8 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS specification. Datasheet 229 Device 0 Memory Mapped I/O Register 19.4.4 SLFRCS - Self-Refresh Channel Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR F14-F17h 00000000h RO; R/WC 32 bits This register is reset by PWROK only. Bit Access Default Value 31:2 RO 00000000h 1 R/WC 0b Description Reserved Warm Reset Event Occurred (RST_EVNT): Cleared by the BIOS by writing a 1 in a warm reset (Reset# asserted while PWROK is asserted) exit sequence. If Memory has not been initialized yet, then memory will not be put into self refresh and the Reset_Warn_Ack message will not be sent. 0 R/WC 0b Channels in Self-refresh: Set by power management hardware after both memory channels are placed in self refresh as a result of a Power State or a Reset Warn sequence, Cleared by Power management hardware before starting self refresh exit sequence initiated by a power management exit. Cleared by the BIOS by writing a 1 in a warm reset (H_CPURST# asserted while PWROK is asserted) exit sequence. 0: Both Channels are not guaranteed to be in self refresh. 1: Both Channels are in self refresh. 19.4.5 GIPMC1 - Graphics Interface Power Management Control 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR FB0h 00h RO; R/W 8 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 230 Datasheet Device 0 Memory Mapped I/O Register 19.4.6 FSBPMC1 - Front Side Bus Power Management Control 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR FB8h 00h RO; R/W 8 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.4.7 UPMC3 - Unit Power Management Control 3 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR FC0-FC3h 00000000h RO; R/W 32 bits 0h This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 19.5 Device 0 MCHBAR Thermal Management Controls Note: The Intel Express Chipset has two internal thermal sensors. The set of registers from MCHBAR Offset 1000h to 101Fh correspond to Thermal Sensor 1 and the set of registers from MCHBAR Offset 1040h to 105Fh correspond to Thermal Sensor 2 respectively. Register Name Register Symbol Reserved Thermal Sensor Control 1 TSC1 Reserved Register End 1000 1000 1001 1002 1003 1003 Default Value Access 0000h R/W/L; R/W; R/WC Thermal Sensor Status 1 TSS1 1004 1005 0000h RO Thermometer Read 1 TR1 1006 1006 FFh RO Thermometer Offset 1 TOF1 1007 1007 00h R/W Relative Thermometer Read 1 RTR1 1008 1008 00h RO 1009 100A 100B 100B 00h RO; R/W/L Reserved Thermometer Integrator Control 1 Datasheet Register Start TIC1 231 Device 0 Memory Mapped I/O Register Register Name Register Symbol Register End Default Value Access Thermometer Moving Average Control 1 TMAC1 100C 100C 00h R/W/L; RO Thermometer Moving Average 1 TMA1 100D 100D 00h RO Thermometer Sample Integrator 1 TSI1 100E 100E 00h RO Temperature Sensor1 Power Management TSPM1 100F 100F 00h R/W Thermal Sensor Temperature Trip Point A1 TSTTPA1 1010 1013 00000000h RO; R/W/L; R/WO Thermal Sensor Temperature Trip Point B1 TSTTPB1 1014 1017 00000000h R/W/L Thermal Calibration Offset 1 TCO1 1018 1018 00h R/W/L 1019 101B Reserved Hardware Throttle Control 1 HWTHROT CTRL1 101C 101C 00h R/W/L; RO; R/WO TCO Fuse 1 TCOFUSE1 101D 101D _0xxx__xx xx_h R/WC; RO Thermal Interrupt Status 1 TIS1 101E 101F 0000h R/WC 1020 1040 1041 1042 0000h R/WC; R/W/L; R/W 1043 1043 Reserved Thermal Sensor Control 2 TSC2 Reserved Thermal Sensor Status 2 TSS2 1044 1045 0000h RO Thermometer Read 2 TR2 1046 1046 FFh RO Thermometer Offset 2 TOF2 1047 1047 00h R/W Relative Thermometer Read 2 RTR2 1048 1048 00h RO 1049 104A Reserved 232 Register Start Thermometer Integrator Control 2 TIC2 104B 104B 00h RO; R/W/L Thermometer Moving Average Control 2 TMAC2 104C 104C 00h R/W/L; RO Thermometer Moving Average 2 TMA2 104D 104D 00h RO Thermometer Sample Integrator 2 TSI2 104E 104E 00h RO Datasheet Device 0 Memory Mapped I/O Register Register Name Register Symbol Register End Default Value Access Temperature Sensor2 Power Management TSPM2 104F 104F 00h R/W Thermal Sensor Temperature Trip Point A2 TSTTPA2 1050 1053 00000000h RO; R/W/L; R/WO Thermal Sensor Temperature Trip Point B2 TSTTPB2 1054 1057 00000000h R/W/L Thermal Calibration Offset 2 TCO2 1058 1058 00h R/W/L 1059 105B Reserved Hardware Throttle Control 2 HWTHROT CTRL2 105C 105C 00h RO; R/W/L; R/WO TCO Fuse 2 TCOFUSE2 105D 105D _0xxx__xx xx_h RO; R/WC Thermal Interrupt Status 2 TIS2 105E 105F 0000h R/WC 1060 1069 1070 1070 00h R/W 1071 107F 1080 1080 06h R/W 1081 10DF Reserved Thermometer Mode Enable and Rate TERATE Reserved Thermal Sensor Rate Control TSRCTRL Reserved Datasheet Register Start In Use Bits IUB 10E0 10E3 00000000h RO; R/WC Thermal Error Command TERRCMD 10E4 10E4 00h R/W Thermal SMI Command TSMICMD 10E5 10E5 00h R/W Thermal SCI Command TSCICMD 10E6 10E6 00h R/W Thermal INTR Command TINTRCMD 10E7 10E7 00h R/W External Thermal Sensor Control and Status EXTTSCS 10EF 10EF 00h R/W; R/WO; R/W/L; RO 233 Device 0 Memory Mapped I/O Register 19.5.1 TSC1 - Thermal Sensor Control 1 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 1001-1002h 0000h R/W/L; R/W; R/WC 16 bits 00h This register controls the operation of the internal thermal sensor located in the graphics hot spot. Bit Access Default Value 15 R/W/L 0b Description Thermal Sensor Enable (TSE): This bit enables power to the thermal sensor. Lockable via TCO1 bit 7. 0: Disabled 1: Enabled 14 R/W 0b 13:10 R/W 0000b Reserved Digital Hysteresis Amount (DHA): This bit determines whether no offset, 1 LSB, 2... 15 is used for hysteresis for the trip points. 0000: digital hysteresis disabled, no offset added to trip temperature 0001: offset is 1 LSB added to each trip temperature when tripped ... 0100: ~3.0C (Recommended setting) ... 1110: 14 LSB added to each trip temperature when tripped 1111: 15 LSB added to each trip temperature when tripped 9 R/W/L 0b Reserved 8 R/WC 0b In Use (IU): Software semaphore bit. After a full (G)MCH RESET, a read to this bit returns a 0. After the first read, subsequent reads will return a 1. A write of a 1 to this bit will reset the next read value to 0. Writing a 0 to this bit has no effect. Software can poll this bit until it reads a 0, and will then own the usage of the thermal sensor. 7:0 234 RO 00h Reserved Datasheet Device 0 Memory Mapped I/O Register 19.5.2 TSS1 - Thermal Sensor Status 1 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 1004-1005h 0000h RO 16 bits 00h This read only register provides trip point and other status of the thermal sensor. Bit Access Default Value 15:11 RO 0h 10 RO 0b Description Reserved Thermometer Mode Output Valid: 1: Thermometer mode is able to converge to a temperature and that the TR1 register is reporting a reasonable estimate of the thermal sensor temperature. 0: Thermometer mode is off, or that temperature is out of range, or that the TR1 register is being looked at before a temperature conversion has had time to complete. 9:6 RO 0h Reserved 5 RO 0b Catastrophic Trip Indicator (CTI): A 1 indicates that the internal thermal sensor temperature is above the catastrophic setting. 4 RO 0b Hot Trip Indicator (HTI): A 1 indicates that the internal thermal sensor temperature is above the Hot setting. 3 RO 0b Aux3 Trip Indicator (A3TI): A 1 indicates that the internal thermal sensor temperature is above the Aux3 setting. 2 RO 0b Aux2 Trip Indicator (A2TI): A 1 indicates that the internal thermal sensor temperature is above the Aux2 setting. 1 RO 0b Aux1 Trip Indicator (A1TI): A 1 indicates that the internal thermal sensor temperature is above the Aux1 setting. 0 RO 0b Aux0 Trip Indicator (A0TI): A 1 indicates that the internal thermal sensor temperature is above the Aux0 setting. Datasheet 235 Device 0 Memory Mapped I/O Register 19.5.3 TR1 - Thermometer Read 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1006h FFh RO 8 bits This register generally provides the calibrated current temperature from the thermometer circuit when the Thermometer mode is enabled. Bit Access Default Value 7:0 RO FFh Description Thermometer Reading (TR): Provides the current counter value. The current counter value corresponds to thermal sensor temperature if TSS1 [10] = 1. This register has a straight binary encoding that will range from 0 to FFh. 19.5.4 TOF1 - Thermometer Offset 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1007h 00h R/W 8 bits This register is used for programming the thermometer offset. Bit Access Default Value 7:0 R/W 00h Description Thermometer Offset (TOF): This value is used to adjust the current thermometer reading so that the TR1 value is not relative to a specific trip or calibration point, and is positive going for positive increases in temperature. The initial default value is 00h and software must determine the correct temperature adjustment that corresponds to a zero reading by reading the fuses and referring to the temperature tables, and then programming the computed offset into this register. 236 Datasheet Device 0 Memory Mapped I/O Register 19.5.5 RTR1 - Relative Thermometer Read 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1008h 00h RO 8 bits This register contains the relative temperature. Bit Access Default Value 7:0 RO 00h Description Relative Thermometer Reading (RTR1): In Thermometer mode, this register reports the relative temperature of the thermal sensor. Provides a two's complement value of the thermal sensor relative to TOF1. TR1 and TSTTPA1.HTPS can both vary between 0 and 255. But RTR1 will be clipped between 127 to keep it an 8-bit number. See also TSS1[10]. Datasheet 237 Device 0 Memory Mapped I/O Register 19.5.6 TIC1 - Thermometer Integrator Control 1 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 100Bh 00h RO; R/W/L 8 bits 0h This register controls the operation of the integrator filter. For a given thermal solution the inter-component thermals may be on the order of tens of seconds, while intracomponent transients may be on the order of milliseconds, the filters are programmable for a range of time intervals. Bit Access Default Value 7 R/W/L 0b Description TIC1 Lock (TIC1LOCK): This bit secures this register. Once a 1 is written to this bit, all the bits of this register become read-only. 6 RO 0b TIC1 Samples (TIC1SAMP): When set to 1, this bit indicates that enough samples have been collected by the integrator over the interval specified by TIC1[2:0]. 5 R/W/L 0b Reserved 4:3 RO 0h Reserved 2:0 R/W/L 0h Sample Interval for the Integrator (TICINTRVL): Sample interval for the integrator 000: p = 4 001: p = 6 010: p = 8 011: p = 10 100: p = 12 101: p = 14 110-111: Reserved This time constant must be greater than or equal to the time constant of the moving average filter (TMAC1[2:0]). 238 Datasheet Device 0 Memory Mapped I/O Register 19.5.7 TMAC1 - Thermometer Moving Average Control 1 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 100Ch 00h R/W/L; RO 8 bits 0h This register controls the operation of the moving average filter. For a given thermal solution the inter-component thermals may be on the order of tens of seconds, while intra-component transients may be on the order of milliseconds, the filters are programmable for a range of time intervals. Bit Access Default Value 7 R/W/L 0b Description TMAC1 Lock (TMACLOCK): This bit secures this register. Once a 1 is written to this bit, all of the configuration register bits are read-only. 6 RO 0b TMAC1 Samples (TMAC1SAMP): When set to 1, this bit indicates that enough samples have been collected by the moving average filter over the interval specified by TMCM. 5:5 RO 0h Reserved 4 R/W/L 0b Throttle Test Mode Enable (TME): This bit is used to shorten the filter. 0: Normal Operation 1: Filter time constant is at 2^27 3:3 RO 0h Reserved 2:0 R/W/L 0h Sample Interval for the Moving Average (TMCINTRVL): Sample interval for the moving average 000: Reserved 001: alpha = 1/4 (p=2) 010: alpha = 1/16 (p=4) 011: alpha = 1/64 (p=6) 100-111: Reserved Datasheet 239 Device 0 Memory Mapped I/O Register 19.5.8 TMA1 - Thermometer Moving Average 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 100Dh 00h RO 8 bits This register provides a moving average of the thermometer samples. Bit Access Default Value 7:0 RO 00h Description Thermometer Reading Moving Average (TMA): This register provides a moving average of thermometer samples. The average is derived via weighted recursive filter with DC pass-through meaning that when the temperature is stable it will read the current temperature. This represents the sample over the interval set in TIC1, TMAC1. After a hardware reset, or when the sample interval is changed, the filter will be cleared and the current temperature will be displayed. 19.5.9 TSI1 - Thermometer Sample Integrator 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 100Eh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Thermometer Sample Integrator (TSI): The integrator accumulates the thermometer samples and integrates over the interval programmed in TIC1, TMAC1. After a hardware reset, or when the sample interval is changed, the filter will be cleared and the current temperature will be displayed. 240 Datasheet Device 0 Memory Mapped I/O Register 19.5.10 TSPM1 - Temperature Sensor1 Power Management B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 100Fh 00h R/W 8 bits 00h This register specifies the power management C-state dependencies for the temperature sensor. Bit Access Default Value Description 7:1 RO 0h Reserved 0 R/W 0b Disable Temperature Sensor When in Lower C-states (DTSCSTATE): 1: When in C2, C3, C4, etc. disable the Temperature Sensor. 0: Do not disable temperature sensor. When the temperature sensor has been disabled, power is no longer being applied. Datasheet 241 Device 0 Memory Mapped I/O Register 19.5.11 TSTTPA1 - Thermal Sensor Temperature Trip Point A1 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR Thermal 1010-1013h 00000000h RO; R/W/L; R/WO 32 bits 00h This register: * Sets the target values for some of the trip points in thermometer mode. * Reports the relative thermal sensor temperature. See also TSTTPB1. Bit Access Default Value 31 R/WO 0b Description Lock Bit For Aux0, Aux1, Aux2 and Aux3 Trip Points (AUXLOCK): This bit, when written to a 1, locks the Aux x Trip point settings. This lock is reversible. The reversing procedure is: following sequence must be done in order without any other configuration cycles in-between write testtp2 04C1C202 write testtp2x 04C1C202 write testtp2x 04C1C202 write testtp2 04C1C202 It is expected that the Aux x Trip point settings can be changed dynamically when this lock is not set. 30:24 RO 0h Reserved 23:16 RO 00h Reserved 15:8 R/W/L 00h Hot Trip Point Setting (HTPS): Sets the target value for the Hot trip point. Lockable via TCO bit 7. 7:0 R/W/L 00h Catastrophic Trip Point Setting (CTPS): Sets the target for the Catastrophic trip point. Lockable via TCO bit 7. 242 Datasheet Device 0 Memory Mapped I/O Register 19.5.12 TSTTPB1 - Thermal Sensor Temperature Trip Point B1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1014-1017h 00000000h R/W/L 32 bits This register sets the target values for some of the trip points in the Thermometer mode. See also TSTTPA1. Bit Access Default Value 31:24 R/W/L 00h Description Aux3 Trip Point Setting (A3TPS): Sets the target value for the Aux3 trip point. Lockable by TSTTPA1[31]. 23:16 R/W/L 00h Aux2 Trip Point Setting (A2TPS): Sets the target value for the Aux2 trip point. Lockable by TSTTPA1[31]. 15:8 R/W/L 00h Aux1 Trip Point Setting (A1TPS): Sets the target value for the Aux1 trip point. Lockable by TSTTPA1[31]. 7:0 R/W/L 00h Aux0 Trip Point Setting (A0TPS): Sets the target value for the Aux0 trip point. Lockable by TSTTPA1[31]. Datasheet 243 Device 0 Memory Mapped I/O Register 19.5.13 TCO1 - Thermal Calibration Offset 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1018h 00h R/W/L 8 bits Bit Access Default Value 7 R/W/L 0b Description Lock Bit for Catastrophic (LBC): This bit, when written to a 1, locks the Catastrophic programming interface, including bits 7:0 of TSTTPA1[15-0], bits 15 and 9 of TSC1. This bit may only be set to a 0 by a hardware reset. Writing a 0 to this bit has no effect. 6:0 R/W/L 00h Calibration Offset (CO): This field contains the current calibration offset for the Thermal Sensor DAC inputs. The calibration offset is a twos complement signed number which is added to the temperature counter value to help generate the final value going to the thermal sensor DAC. This field is Read/Write and can be modified by Software unless locked by setting bit 7 of this register. Once this register has been overwritten by software, the values of the TCO fuses can be read using the Therm3 register. Note for TCO operation: While this is a seven-bit field, the 7th bit is sign extended to 9 bits for TCO operation. Register Field Value 244 Binary Value 00h to 3Fh 000 0000 to 011 1111 41h to 7Fh 100 0001 to 111 1111 Datasheet Device 0 Memory Mapped I/O Register 19.5.14 HWTHROTCTRL1 - Hardware Throttle Control 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 101Ch 00h R/W/L; RO; R/WO 8 bits Bit Access Default Value 7 R/W/L 0b Description Internal Thermal Hardware Throttling Enable Bit (ITHTE): This bit is a master enable for internal thermal sensor-based hardware throttling 0: Hardware actions via the internal thermal sensor are disabled. 1: Hardware actions via the internal thermal sensor are enabled. 6:5 RO 00b 4 R/W/L 0b Reserved Throttling Zone Selection (TZS): This bit determines what temperature zones will enable auto throttling. This register applies to internal thermal sensor throttling. Lockable by bit0 of this register. See also the throttling registers in PCI configuration space Device 0 which is used to enable or disable throttling 0: Hot, Aux2, and Catastrophic. 1: Hot and Catastrophic. 3 R/W/L 0b Halt on Catastrophic (HOC): When this bit is set, THRMTRIP# is asserted on catastrophic trip to bring the platform down. A system reboot is required to bring the system out of a halt from the thermal sensor. Once the catastrophic trip point is reached, THRMTRIP# will stay asserted even if the catastrophic trip deasserts before the platform is shut down. Datasheet 2:1 R/W/L 00b Reserved 0 R/WO 0b Reserved 245 Device 0 Memory Mapped I/O Register 19.5.15 TCOFUSE1 - TCO Fuse 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 101Dh _0xxx__xxxx_h R/WC; RO 8 bits Bit Access Default Value 7 R/WC 0b Description INUSE_STS (INUSESTS): Software semaphore bit. After a full (G)MCH RESET, a read to this bit returns a 0. After the first read, subsequent reads will return a 1. A write of a 1 to this bit will reset the next read value to 0. Writing a 0 to this bit has no effect. Software can poll this bit until it reads a 0, and will then own the usage of the thermal sensor. This bit has no other effect on the hardware, and is only used as a semaphore among various independent software threads that may need to use the thermal sensor. Software that reads this register but does not intend to claim exclusive access of the resource managed by this bit must write a 1 to this bit if it reads a 0, in order to allow other software threads to claim it. 6:0 RO N/A TCO Fuses (TCOFUSE): This 7 bit field gives the value of the trimming fuses for TCO. The register always reports the settings of all 7 thermal fuses. Note for TCO operation: While this is a seven bit field, the 7th bit is sign extended to 9 bits for TCO operation. Register Field Value 246 Binary Value 00h to 3Fh 000 0000 to 011 1111 41h to 7Fh 100 0001 to 111 1111 Datasheet Device 0 Memory Mapped I/O Register 19.5.16 TIS1 - Thermal Interrupt Status 1 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 101E-101Fh 0000h R/WC 16 bits 0h Bit Access Default Value Description 15:14 RO 0h Reserved 13 R/WC 0b Was Catastrophic Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that a Catastrophic Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 12 R/WC 0b Was Hot Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that a Hot Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 11 R/WC 0b Was Aux3 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux3 Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 10 R/WC 0b Was Aux2 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux2 Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 9 R/WC 0b Was Aux1 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux1 Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 8 R/WC 0b Was Aux0 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux0 Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 7:6 Datasheet RO 0h Reserved 247 Device 0 Memory Mapped I/O Register Bit Access Default Value 5 R/WC 0b Description Catastrophic Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that a Catastrophic Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. 0: No trip for this event. Software must write a 1 to clear this status bit. 4 R/WC 0b Hot Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that a Hot Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. 3 R/WC 0b Aux3 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. 2 R/WC 0b Aux2 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. 1 R/WC 0b Aux1 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux1 Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. 0 R/WC 0b Aux0 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux0 Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. 248 Datasheet Device 0 Memory Mapped I/O Register 19.5.17 TSC2 - Thermal Sensor Control 2 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 1041-1042h 0000h R/WC; R/W/L; R/W 16 bits 00h This register controls the operation of the internal thermal sensor located in the memory hot spot. Bit Access Default Value 15 R/W/L 0b Description Thermal Sensor Enable (TSE): This bit enables power to the thermal sensor. Lockable via TCO2 bit 7. 0: Disabled 1: Enabled 14 R/W 0b 13:10 R/W 0000b Reserved Digital Hysteresis Amount (DHA): This bit determines whether no offset, 1 LSB, 2... 15 is used for hysteresis for the trip points. 0000 = digital hysteresis disabled, no offset added to trip temperature 0001 = offset is 1 LSB added to each trip temperature when tripped ... 0100~3.0C (Recommended setting) ... 1110 = offset is 14 LSB added to each trip temperature when tripped 1111 = offset is 15 LSB added to each trip temperature when tripped 9 R/W/L 0b Reserved 8 R/WC 0b In Use (IU): Software semaphore bit. After a full H/W (G)MCH RESET, a read to this bit returns a 0. After the first read, subsequent reads will return a 1. A write of a 1 to this bit will reset the next read value to 0. Writing a 0 to this bit has no effect. Software can poll this bit until it reads a 0, and will then own the usage of the thermal sensor. 7:0 Datasheet RO 0h Reserved 249 Device 0 Memory Mapped I/O Register 19.5.18 TSS2 - Thermal Sensor Status 2 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 1044-1045h 0000h RO 16 bits 00h This read only register provides trip point and other status of the thermal sensor. Bit Access Default Value Description 15:11 RO 0h Reserved 10 RO 0b Thermometer Mode Output Valid (TMOMVAL2): A 1 indicates the Thermometer mode is able to converge to a temperature and that the TR2 register is reporting a reasonable estimate of the thermal sensor temperature. A 0 indicates the Thermometer mode is off, or that temperature is out of range, or that the TR2 register is being looked at before a temperature conversion has had time to complete. 9 RO 0b Reserved 8:6 RO 0h Reserved 5 RO 0b Catastrophic Trip Indicator (CTI): A 1 indicates that the internal thermal sensor temperature is above the catastrophic setting. 4 RO 0b Hot Trip Indicator (HTI): A 1 indicates that the internal thermal sensor temperature is above the Hot setting. 3 RO 0b Aux3 Trip Indicator (A3TI): A 1 indicates that the internal thermal sensor temperature is above the Aux3 setting. 2 RO 0b Aux2TripIndicator (A2TI): A 1 indicates that the internal thermal sensor temperature is above the Aux2 setting. 1 RO 0b Aux1TripIndicator (A1TI): A 1 indicates that the internal thermal sensor temperature is above the Aux1 setting. 0 RO 0b Aux0TripIndicator (A0TI): A 1 indicates that the internal thermal sensor temperature is above the Aux0 setting. 250 Datasheet Device 0 Memory Mapped I/O Register 19.5.19 TR2 - Thermometer Read 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1046h FFh RO 8 bits This register generally provides the calibrated current temperature from the thermometer circuit when the Thermometer mode is enabled. Bit Access Default Value 7:0 RO FFh Description Thermometer Reading (TR): Provides the current counter value. The current counter value corresponds to thermal sensor temperature if TSS2[10] = 1 . This register has a straight binary encoding that will range from 0 to FFh. 19.5.20 TOF2 - Thermometer Offset 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1047h 00h R/W 8 bits This register is used to program the thermometer offset Bit Access Default Value 7:0 R/W 00h Description Thermometer Offset (TOF): This value is used to adjust the current thermometer reading so that the TR value is not relative to a specific trip or calibration point, and is positive going for positive increases in temperature. The initial default value is 00h and software must determine the correct temperature adjustment that corresponds to a zero reading by reading the fuses and referring to the temperature tables, and then programming the computed offset into this register. Datasheet 251 Device 0 Memory Mapped I/O Register 19.5.21 RTR2 - Relative Thermometer Read 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1048h 00h RO 8 bits This register contains the relative temperature. Bit Access Default Value 7:0 RO 00h Description Relative Thermometer Reading (RTR2): In Thermometer mode, this register reports the relative temperature of the thermal sensor. Provides a two's complement value of the thermal sensor relative to TOF2. TR2 and TSTTPA2.HTPS can both vary between 0 and 255. But RTR2 will be clipped between 127 to keep it an 8-bit number. See also TSS2[10]. 252 Datasheet Device 0 Memory Mapped I/O Register 19.5.22 TIC2 - Thermometer Integrator Control 2 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 104Bh 00h RO; R/W/L 8 bits 0h This register controls the operation of the integrator filter. For a given thermal solution the inter-component thermals may be on the order of tens of seconds, while intracomponent transients may be on the order of milliseconds, the filters are programmable for a range of time intervals. Bit Access Default Value 7 R/W/L 0b Description TIC2 Lock (TIC2LOCK): This bit secures this register. Once a 1 is written to this bit, all the bits of this register become read-only. 6 RO 0b TIC2 Samples (TIC2SAMP): When set to 1 this bit indicates that enough samples have been collected by the integrator over the interval specified by TIC2[2:0]. 5 R/W/L 0b Throttle Test Mode Enable (TME): This bit is used to shorten the filter. 0: Normal Operation 1: Filter time constant is at 2^7 4:3 RO 0h Reserved 2:0 R/W/L 0h Sample interval for the integrator (TICINTRVL): Sample interval for the integrator 000: p = 4 001: p = 6 010: p = 8 011: p = 10 100: p = 12 101: p = 14 110-111: Reserved This time constant must be greater than or equal to the time constant of the moving average filter (TMAC2[2:0]). Datasheet 253 Device 0 Memory Mapped I/O Register 19.5.23 TMAC2 - Thermometer Moving Average Control 2 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 104Ch 00h R/W/L; RO 8 bits 0h This register controls the operation of the moving average filter. For a given thermal solution the inter-component thermals may be on the order of tens of seconds, while intra-component transients may be on the order of milliseconds, the filters are programmable for a range of time intervals. Bit Access Default Value 7 R/W/L 0b Description TMAC2 Lock (TMACLOCK): This bit secures this register Once a 1 is written to this bit, all of the configuration register bits are read-only. 6 RO 0b TMAC2 Samples (TMAC2SAMP): When set to 1 this bit indicates that enough samples have been collected by the moving average filter over the interval specified by TMCM. 5:5 RO 0h Reserved 4 R/W/L 0b Throttle Test Mode Enable (TME): This bit is used to shorten the filter. 0: Normal Operation 1: Filter time constant is at 2^27 3:3 RO 0h Reserved 2:0 R/W/L 0h Sample Interval for the Moving Average (TMCINTRVL): Sample interval for the moving average 000: alpha = 1 (p=0) 001: alpha = 1/4 (p=2) 010: alpha = 1/16 (p=4) 011: alpha = 1/64 (p=6) 100-111: Reserved 254 Datasheet Device 0 Memory Mapped I/O Register 19.5.24 TMA2 - Thermometer Moving Average 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 104Dh 00h RO 8 bits This register provides a moving average of the thermometer samples. Bit Access Default Value 7:0 RO 00h Description Thermometer Reading Moving Average (TMA): This register provides a moving average of thermometer samples. The average is derived via weighted recursive filter with DC pass-through meaning that when the temperature is stable it will read the current temperature. This represents the sample over the interval set in TIC2, TMAC2. After a hardware reset, or when the sample interval is changed, the filter will be cleared and the current temperature will be displayed. 19.5.25 TSI2 - Thermometer Sample Integrator 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 104Eh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Thermometer Sample Integrator (TSI): The integrator accumulates the thermometer samples and integrates over the interval programmed in TIC2, TMAC2. After a hardware reset, or when the sample interval is changed, the filter will be cleared and the current temperature will be displayed. Datasheet 255 Device 0 Memory Mapped I/O Register 19.5.26 TSPM2 - Temperature Sensor2 Power Management B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 104Fh 00h R/W 8 bits 00h This register specifies the power management C-state dependencies for the temperature sensor. Bit Access Default Value Description 7:1 RO 0h Reserved 0 R/W 0b Disable Temperature Sensor When in Lower C-states (DTSCSTATE): 1: When in C2, C3, C4, etc. Disable the Temperature Sensor. 0: Do not disable temperature sensor. When the temperature sensor has been disabled, power is no longer being applied. 256 Datasheet Device 0 Memory Mapped I/O Register 19.5.27 TSTTPA2 - Thermal Sensor Temperature Trip Point A2 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default This register: 0/0/0/MCHBAR 1050-1053h 00000000h RO; R/W/L; R/WO 32 bits 00h * Sets the target values for some of the trip points in thermometer mode. * Reports the relative thermal sensor temperature. See also TSTTPB2. Bit Access Default Value 31 R/WO 0b Description Lock Bit for Aux0, Aux1, Aux2 and Aux3 Trip Points (AUXLOCK): This bit, when written to a 1, locks the Aux x Trip point settings. This lock is reversible. The reversing procedure is that the following sequence must be done in order without any other configuration cycles in between. write testtp2 04C1C202 write testtp2x 04C1C202 write testtp2x 04C1C202 write testtp2 04C1C202 NOTE: It is expected that the Aux x Trip point settings can be changed dynamically when this lock is not set. 30:24 RO 0h Reserved 23:16 RO 00h Reserved 15:8 R/W/L 00h Hot Trip Point Setting (HTPS): Sets the target value for the Hot trip point. Lockable via TCO bit 7. 7:0 R/W/L 00h Catastrophic Trip Point Setting (CTPS): Sets the target for the Catastrophic trip point. Lockable via TCO bit 7. Datasheet 257 Device 0 Memory Mapped I/O Register 19.5.28 TSTTPB2 - Thermal Sensor Temperature Trip Point B2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1054-1057h 00000000h R/W/L 32 bits This register sets the target values for some of the trip points in the Thermometer mode. See also TSTTPA2. Bit Access Default Value 31:24 R/W/L 00h Description Aux3 Trip Point Setting (A3TPS): Sets the target value for the Aux3 trip point. Lockable by TSTTPA2[31]. 23:16 R/W/L 00h Aux2 Trip Point Setting (A2TPS): Sets the target value for the Aux2 trip point. Lockable by TSTTPA2[31]. 15:8 R/W/L 00h Aux1 Trip Point Setting (A1TPS): Sets the target value for the Aux1 trip point. Lockable by TSTTPA2[31]. 7:0 R/W/L 00h Aux0 Trip Point Setting (A0TPS): Sets the target value for the Aux0 trip point. Lockable by TSTTPA2[31]. 258 Datasheet Device 0 Memory Mapped I/O Register 19.5.29 TCO2 - Thermal Calibration Offset 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1058h 00h R/W/L 8 bits Bit Access Default Value 7 R/W/L 0b Description Lock Bit for Catastrophic (LBC): This bit, when written to a 1, locks the Catastrophic programming interface, including bits 7:0 of TSTTPA2[15-0], bits 15 and 9 of TSC2. This bit may only be set to a 0 by a hardware reset. Writing a 0 to this bit has no effect. 6:0 R/W/L 00h Calibration Offset (CO): This field contains the current calibration offset for the Thermal Sensor DAC inputs. The calibration offset is a twos complement signed number which is added to the temperature counter value to help generate the final value going to the thermal sensor DAC. This field is Read/Write and can be modified by Software unless locked by setting bit 7 of this register. The fuses cannot be programmed via this register. Once this register has been overwritten by software, the values of the TCO fuses can be read using the Therm3 register. Note for TCO operation: While this is a seven-bit field, the 7th bit is sign extended to 9 bits for TCO operation. Register Field Value Datasheet Binary Value 00h to 3Fh 000 0000 to 011 1111 41h to 7Fh 100 001 to 111 1111 259 Device 0 Memory Mapped I/O Register 19.5.30 HWTHROTCTRL2 - Hardware Throttle Control 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 105Ch 00h RO; R/W/L; R/WO 8 bits Bit Access Default Value 7 R/W/L 0b Description Internal Thermal Hardware Throttling Enable bit (ITHTE): This bit is a master enable for internal thermal sensor-based hardware throttling. 0: Hardware actions via the internal thermal sensor are disabled. 1: Hardware actions via the internal thermal sensor are enabled. 6:5 RO 00b 4 R/W/L 0b Reserved Throttling Zone Selection (TZS): This bit determines what temperature zones will enable auto throttling. This register applies to internal thermal sensor throttling. Lockable by bit0 of this register. See also the throttling registers in PCI config space Device 0 which is used to enable or disable throttling. 0: Hot, Aux2, and Catastrophic. 1: Hot and Catastrophic. 3 R/W/L 0b Halt on Catastrophic (HOC): When this bit is set, THRMTRIP# is asserted on catastrophic trip to bring the platform down. A system reboot is required to bring the system out of a halt from the thermal sensor. Once the catastrophic trip point is reached, THRMTRIP# will stay asserted even if the catastrophic trip deasserts before the platform is shut down. 260 2:1 R/W/L 00b Reserved 0 R/WO 0b Reserved Datasheet Device 0 Memory Mapped I/O Register 19.5.31 TCOFUSE2 - TCO Fuse 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 105Dh _0xxx__xxxx_h RO; R/WC 8 bits Bit Access Default Value 7 R/WC 0b Description INUSE_STS (INUSESTS): Software semaphore bit. After a full (G)MCH RESET, a read to this bit returns a 0. After the first read, subsequent reads will return a 1. A write of a 1 to this bit will reset the next read value to 0. Writing a 0 to this bit has no effect. Software can poll this bit until it reads a 0, and will then own the usage of the thermal sensor. This bit has no other effect on the hardware, and is only used as a semaphore among various independent software threads that may need to use the thermal sensor. Software that reads this register but does not intend to claim exclusive access of the resource managed by this bit must write a one to this bit if it reads a 0, in order to allow other software threads to claim it. 6:0 RO N/A TCO Fuses (TCOFUSE): This 7-bit field gives the value of the trimming fuses for TCO. The register always reports the settings of all 7 thermal fuses. Note for TCO operation: While this is a seven bit field, the 7th bit is sign extended to 9 bits for TCO operation. Register Field Value Datasheet Binary Value 00h to 3Fh 000 0000 to 011 1111 41h to 7Fh 100 001 to 111 1111 261 Device 0 Memory Mapped I/O Register 19.5.32 TIS2 - Thermal Interrupt Status 2 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 105E-105Fh 0000h R/WC 16 bits 0h Bit Access Default Value Description 15:14 RO 0h Reserved 13 R/WC 0b Was Catastrophic Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that a Catastrophic Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 12 R/WC 0b Was Hot Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that a Hot Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 11 R/WC 0b Was Aux3 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux3 Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 10 R/WC 0b WasAux2ThermalSensorInterruptEvent: 0: No trip for this event. 1: Indicates that an Aux2 Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 9 R/WC 0b Was Aux1 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux1 Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 8 R/WC 0b Was Aux0 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux0 Thermal Sensor trip based on a higher to lower temperature transition thru the trip point. Software must write a 1 to clear this status bit. 7:6 262 RO 0h Reserved Datasheet Device 0 Memory Mapped I/O Register Bit Access Default Value 5 R/WC 0b Description Catastrophic Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that a Catastrophic Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. 4 R/WC 0b Hot Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that a Hot Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. 3 R/WC 0b Aux3 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. 2 R/WC 0b Aux2 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. 1 R/WC 0b Aux1 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux1 Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. 0 R/WC 0b Aux0 Thermal Sensor Interrupt Event: 0: No trip for this event. 1: Indicates that an Aux0 Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. Software must write a 1 to clear this status bit. Datasheet 263 Device 0 Memory Mapped I/O Register 19.5.33 TERATE - Thermometer Mode Enable and Rate B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR Thermal 1070h 00h R/W; 8 bits 0h This common register helps select between the analog and the thermometer mode and also helps select the DAC settling timer. This register bit field shall contain the default value unless otherwise indicated in the BIOS specification. 264 Datasheet Device 0 Memory Mapped I/O Register 19.5.34 TSRCTRL - Thermal Sensor Rate Control B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 1080h 06h R/W 8 bits 0h This register controls the conversion duration and slow clock duration of the thermal sensor. Bit Access Default Value Description 7:4 RO 0h Reserved 3 R/W 0b conversion duration (TSCD): 0: 128 fast clocks 1:32 fast clocks (normal mode operation) 2:0 R/W 110b Slow clock control (SCC): Sample interval for the slow clock. 000: 25 6 sec (will not work with all settings for fast clock) 001: 512 sec (will not work with all settings for fast clock) 010: 1024 sec 011: 2048 sec 100: 4096 sec 101: 8192 sec 110: 16384 sec (normal thermometer mode operation, presilicon) 111: 32768 sec Legal settings must obey following restriction: 100 sec for thermal sensor settling +32 * fast clock + 1 sec clock granularity < slow clock control setting if Conversion duration = 0 100 sec for thermal sensor settling +128 * fast clock + 1 sec clock granularity < slow clock control setting if Conversion duration = 1 Datasheet 265 Device 0 Memory Mapped I/O Register 19.5.35 IUB - In Use Bits B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 10E0-10E3h 00000000h RO; R/WC 32 bits Semaphore bits available for SW. Bit Access Default Value 31:25 RO 00h 24 R/WC 0b Description Reserved In Use Bit3 (IU3): Software semaphore bit. After a full (G)MCH RESET, a read to this bit returns a 0. After the first read, subsequent reads will return a 1. A write of a 1 to this bit will reset the next read value to 0. Writing a 0 to this bit has no effect. Software can poll this bit until it reads a 0, and will then own the usage of the resource with which software associates it. 23:17 RO 00h 16 R/WC 0b Reserved In Use Bit2 (IU2): Software semaphore bit. After a full (G)MCH RESET, a read to this bit returns a 0. After the first read, subsequent reads will return a 1. A write of a 1 to this bit will reset the next read value to 0. Writing a 0 to this bit has no effect. Software can poll this bit until it reads a 0, and will then own the usage of the resource with which software associates it. 15:9 RO 00h 8 R/WC 0b Reserved In Use Bit1 (IU1): Software semaphore bit. After a full (G)MCH RESET, a read to this bit returns a 0. After the first read, subsequent reads will return a 1. A write of a 1 to this bit will reset the next read value to 0. Writing a 0 to this bit has no effect. Software can poll this bit until it reads a 0, and will then own the usage of the resource with which software associates it. 7:1 RO 00h 0 R/WC 0b Reserved In Use Bit0 (IU0): Software semaphore bit. After a full (G)MCH RESET, a read to this bit returns a 0. After the first read, subsequent reads will return a 1. A write of a 1 to this bit will reset the next read value to 0. Writing a 0 to this bit has no effect. Software can poll this bit until it reads a 0, and will then own the usage of the resource with which software associates it. 266 Datasheet Device 0 Memory Mapped I/O Register 19.5.36 TERRCMD - Thermal Error Command B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 10E4h 00h R/W 8 bits 0h This register select which errors are generate a SERR DMI interface special cycle, as enabled by ERRCMD [SERR Thermal Sensor event].The SERR and SCI must not be enabled at the same time for the thermal sensor event. Bit Access Default Value 7:6 RO 0h 5 R/W 0b Description Reserved SERR on Catastrophic Thermal Sensor Event: 0: Disable. 1: Enable. 4 R/W 0b SERR on Hot Thermal Sensor Event: 0: Disable. 1: Enable. 3 R/W 0b SERR on Aux3 Thermal Sensor Event: 0: Disable. 1: Enable. 2 R/W 0b SERR on Aux2 Thermal Sensor Event: 0: Disable. 1: Enable. 1 R/W 0b SERR on Aux1 Thermal Sensor Event: 0: Disable. 1: Enable. 0 R/W 0b SERR on Aux0 Thermal Sensor Event: 0: Disable. 1: Enable. Datasheet 267 Device 0 Memory Mapped I/O Register 19.5.37 TSMICMD - Thermal SMI Command B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 10E5h 00h R/W 8 bits 0h This register selects specific errors to generate a SMI DMI cycle, as enabled by the SMI Error Command Register[SMI on Thermal Sensor Trip] . Bit Access Default Value 7:6 RO 0h 5 R/W 0b Description Reserved SMI on Catastrophic Thermal Sensor Trip: 0: Disable. 1: Enable. 4 R/W 0b SMI on Hot Thermal Sensor Trip: 0: Disable. 1: Enable. 3 R/W 0b SMI on Aux3 Thermal Sensor Trip: 0: Disable. 1: Enable. 2 R/W 0b SMI on Aux2 Thermal Sensor Trip: 0: Disable. 1: Enable. 1 R/W 0b SMI on Aux1 Thermal Sensor Trip: 0: Disable. 1: Enable. 0 R/W 0b SMI on Aux0 Thermal Sensor Trip: 0: Disable. 1: Enable. 268 Datasheet Device 0 Memory Mapped I/O Register 19.5.38 TSCICMD - Thermal SCI Command B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 10E6h 00h R/W 8 bits 0h This register selects specific errors to generate a SCI DMI cycle, as enabled by the SCI Error Command Register[SCI on Thermal Sensor Trip].The SCI and SERR must not be enabled at the same time for the thermal sensor event. Bit Access Default Value 7:6 RO 0h 5 R/W 0b Description Reserved SCI on Catastrophic Thermal Sensor Trip: 0: Disable. 1: Enable. 4 R/W 0b SCI on Hot Thermal Sensor Trip: 0: Disable. 1: Enable. 3 R/W 0b SCI on Aux3 Thermal Sensor Trip: 0: Disable. 1: Enable. 2 R/W 0b SCI on Aux2 Thermal Sensor Trip: 0: Disable. 1: Enable. 1 R/W 0b SCI on Aux1 Thermal Sensor Trip: 0: Disable. 1: Enable. 0 R/W 0b SCI on Aux0 Thermal Sensor Trip: 0: Disable. 1: Enable. Datasheet 269 Device 0 Memory Mapped I/O Register 19.5.39 TINTRCMD - Thermal INTR Command B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 10E7h 00h R/W 8 bits 0h This register selects specific errors to generate an INT DMI cycle. Bit Access Default Value Description 7:6 RO 0h Reserved 5 R/W 0b INTR on Catastrophic Thermal Sensor Trip: 1 = A INTR DMI cycle is generated by (G)MCH. 4 R/W 0b INTR on Hot Thermal Sensor Trip: 1 = A INTR DMI cycle is generated by (G)MCH. 3 R/W 0b INTR on Aux3 Thermal Sensor Trip: 1 = A INTR DMI cycle is generated by (G)MCH. 2 R/W 0b INTR on Aux2 Thermal Sensor Trip: 1 = A INTR DMI cycle is generated by (G)MCH. 1 R/W 0b INTR on Aux1 Thermal Sensor Trip: 1 = A INTR DMI cycle is generated by (G)MCH. 0 R/W 0b INTR on Aux0 Thermal Sensor Trip: 1 = A INTR DMI cycle is generated by (G)MCH. 270 Datasheet Device 0 Memory Mapped I/O Register 19.5.40 EXTTSCS - External Thermal Sensor Control and Status B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 10EFh 00h R/W; R/WO; R/W/L; RO 8 bits 0h Bit Access Default Value Description 7 R/WO 0b External Sensor Enable: Setting this bit to 1 locks the lockable bits in this register. This bit may only be set to a zero by a hardware reset. Once locked, writing a 0 to bit has no effect. If both internal sensor throttling and external write sensor throttling are enabled, either can initiate throttling. 0: External Sensor input is disabled. 1: External Sensor input is enabled. 6 R/W/L 0b Throttling Type Select (TTS): Lockable by EXTTSCS [7]. If External Thermal Sensor Enable = 1, then 0: DRAM throttling based on the settings in the Device 0 MCHBAR DRAM Throttling Control register (C0DTC). 1: (G)MCH throttling, based on the settings in the Device 0 MCHBAR (C0GTC). 5 R/W/L 0b EXTTS1 Action Select (AS1): Lockable by EXTTSCS [7] = 1. 0: The external sensor trip functions same as a Thermometer mode hot trip. 1: The external sensor trip functions as a Thermometer mode aux0 trip. See clarification note below. NOTE: This bit is N/A when fast C4e exit is enabled. 4 R/W/L 0b EXTTS0 Action Select (AS0): Lockable by EXTTSCS [7]. 0: The external sensor trip functions same as a Thermometer mode catastrophic trip. 1: The external sensor trip functions same as a Thermometer mode hot trip. NOTE: See clarification note below. 3 RO 0b EXTTS0 Trip Indicator (S0TI): A 1 indicates that an externally monitored temperature is exceeding the programmed setting of an external thermal sensor. 2 RO 0b EXTTS1 Trip Indicator (S1TI): A 1 indicates that an externally monitored temperature is exceeding the programmed setting of an external thermal sensor. This bit is N/A when fast C4e exit is enabled. Datasheet 271 Device 0 Memory Mapped I/O Register Bit Access Default Value Description 1:1 RO 0h Reserved 0 R/W 0b External Thermal Sensor Signals Routing Control: 0: Route all external sensor signals to affect internal thermal sensor 1 registers, as appropriate. 1: Route all external sensor signals to affect internal thermal sensor 2 registers, as appropriate. 19.6 MCHBAR Render Thermal Throttling Register Name Register Symbol Reserved VID and Frequency Relationship Table 1 VIDFREQ1 Reserved Register End Default Value Access 1100 1101 0000h R/W 1110 1113 00000000h R/W 1114 111F Internal to External VID Mapping Table 1 INTTOEXT1 1120 1123 00000000h R/W; RO Internal to External VID Mapping Table 2 INTTOEXT2 1124 1127 00000000h R/W; RO Internal to External VID Mapping Table 3 INTTOEXT3 1128 112B 00000000h R/W; RO 112C 11AF Reserved Thermal State Control THERMSTCTL 11B0 11B3 00000000h R/W Render Standby State Control RSTDBYCTL 11B8 11BB 00000000h R/W 11BC 11BF Reserved VID Control VIDCTL 11C0 11C3 00000000h R/W VID Control 1 VIDCTL1 11C4 11C7 00000000h R/W 11C8 11E9 Reserved 272 Register Start Datasheet Device 0 Memory Mapped I/O Register 19.6.1 VIDFREQ1 - VID and Frequency Relationship Table 1 B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default Datasheet 0/0/0/MCHBAR 1110-1113h 00000000h R/W; 32 bits 0000h Bit Access Default Value Description 31:28 RO 0h 27:24 R/W 0000b 23:20 RO 0h 19:16 R/W 0000b 15:12 RO 0h 11:8 R/W 0000b 7:4 RO 0h Reserved 3:0 R/W 0000b Reserved Reserved VID Point -- P0 (VIDP0): Reserved P0 Frequency (P0FREQ): Reserved VID Point -- P1 (VIDP1): 273 Device 0 Memory Mapped I/O Register 19.6.2 INTTOEXT1 - Internal to External VID Mapping Table 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 19.6.3 0/0/0/MCHBAR 1120-1123h 00000000h R/W; RO; 32 bits Bit Access Default Value 31:28 RO 0h 27:24 R/W 0000b 23:20 RO 0h 19:16 R/W 0000b 15:12 RO 0h 11:8 R/W 0000b 7:4 RO 0h 3:0 R/W 0000b Reserved External Mapping for Internal Mapping 15 (MAP15): External mapping for internal mapping 15 Reserved External Mapping for Internal Mapping 14 (MAP14) Reserved External Mapping for Internal Mapping 13 (MAP13) Reserved External Mapping for Internal Mapping 12 (MAP12) INTTOEXT2 - Internal to External VID Mapping Table 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 274 Description 0/0/0/MCHBAR 1124-1127h 00000000h R/W; RO; 32 bits Bit Access Default Value 31:28 RO 0h 27:24 R/W 0000h 23:20 RO 0h 19:16 R/W 0000b 15:12 RO 0h 11:8 R/W 0000b 7:4 RO 0h 3:0 R/W 0000b Description Reserved External Mapping for Internal Mapping 11 (MAP11) Reserved External Mapping for Internal Mapping 10 (MAP10) Reserved External Mapping for Internal Mapping 9 (MAP9) Reserved External Mapping for Internal Mapping 8 (MAP8) Datasheet Device 0 Memory Mapped I/O Register 19.6.4 INTTOEXT3 - Internal to External VID Mapping Table 3 B/D/F/Type: Address Offset: Default Value: Access: Size: Datasheet 0/0/0/MCHBAR 1128-112Bh 00000000h R/W; RO; 32 bits Bit Access Default Value Description 31:28 RO 0h Reserved 27:24 R/W 0h External Mapping for Internal Mapping 7 (MAP7) 23:20 RO 0h Reserved 19:16 R/W 0000b 15:12 RO 0h 11:8 R/W 0000b 7:4 RO 0h 3:0 R/W 0000b External Mapping for Internal Mapping 6 (MAP6) Reserved External Mapping for Internal Mapping 5 (MAP5) Reserved: External Mapping for Internal Mapping 4 (MAP4) 275 Device 0 Memory Mapped I/O Register 19.6.5 THERMSTCTL - Thermal State Control B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 11B0-11B3h 00000000h R/W; 32 bits 00000h This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification 19.6.6 RSTDBYCTL - Render Standby State Control B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/0/0/MCHBAR 11B8-11BBh 00000000h R/W; 32 bits 000h Bit Access Default Value Description 31 R/W 0b Reserved 30 R/W 0b RS2 Enable (RS2EN): 0: RS2 not enabled 1: RS2 enabled 29:0 276 R/W 0000000h Reserved Datasheet Device 0 Memory Mapped I/O Register 19.6.7 VIDCTL - VID Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 11C0-11C3h 00000000h R/W; 32 bits Bit Access Default Value 31:24 R/W 00h Description VID Up Time (VIDUPTIME): 0 = 255 s 1 = 1 s 255 = 255 s 23:16 R/W 00h VID Down Time (VIDDNTIME): 0 = 255 s 1 = 1 s 255 = 255 s 15:0 19.6.8 R/W 0000h Reserved VIDCTL1 - VID Control 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 11C4-11C7h 00000000h R/W; 32 bits This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. Datasheet Bit Access Default Value 31:0 R/W 00000000h Description Reserved 277 Device 0 Memory Mapped I/O Register 19.7 Device 0 MCHBAR DRAM Controls Register Name Channel 0 DRAM Rank Boundary 0/1 Register Symbol C0DRB01 Reserved Register End 1200 1203 1204 1207 Default Value Access 00000000h RO; R/W Channel 0 DRAM Rank 0,1 Attribute C0DRA 1208 120B 00000000h RO; R/W Channel 0 DRAM Clock Disable C0DCLKDIS 120C 120F 00000000h RO; R/W Channel 0 DRAM Timing Register 0 C0DRT0 1210 1213 34B10461h R/W; RO Channel 0 DRAM Timing Register 1 C0DRT1 1214 1217 11E08463h RO; R/W Channel 0 DRAM Timing Register 2 C0DRT2 1218 121B 2200105Fh RO; R/W Channel 0 DRAM Timing Register 3 C0DRT3 121C 121F 01056101h RO; R/W Channel 0 DRAM Timing Register 4 C0DRT4 1220 1223 29503C32h RO; R/W Channel 0 DRAM timing Register 5 C0DRT5 1224 1227 62C32020h RO; R/W 1228 122F Reserved Channel 0 DRAM Controller Mode 0 C0DRC0 1230 1233 40000002h RO; R/W Channel 0 DRAM Controller Mode 1 C0DRC1 1234 1237 00000000h RO; R/W Channel 0 DRAM Controller Mode 2 C0DRC2 1238 123B 00000000h RO; R/W 123C 124F 1250 1257 0000000000 000000h RO; R/W 1258 126B 126C 126F 00000000h RO; R/W Reserved Channel 0 Adaptive Idle Timer Control C0AIT Reserved Channel 0 (G)MCH Throttling Event Weight 1 278 Register Start C0DTEW1 Datasheet Device 0 Memory Mapped I/O Register Register Name Register Symbol Register End Default Value Access Channel 0 (G)MCH Throttling Event Weight C0GTEW 1270 1273 00000000h R/W/L Channel 0 (G)MCH Throttling Control C0GTC 1274 1277 00000000h R/W/L; RO Channel 0 DRAM Rank Throttling Passive Event C0DTPEW 1278 127F 0000000000 000000h RO; R/W/L Channel 0 DRAM Rank Throttling Active Event C0DTAEW 1280 1287 0000000000 000000h RO; R/W/L Channel 0 DRAM Throttling Control C0DTC 1288 128B 00000000h R/W/L; RO 128C 12FF 1300 1303 00000000h RO; R/W 1304 1307 00000000h RO; R/W Reserved Channel 1 DRAM Rank Boundary 0/1 C1DRB01 Reserved Channel 1 DRAM Rank 0,1 Attribute C1DRA 1308 130B 00000000h RO; R/W Channel 1 DRAM Clock Disable C1DCLKDIS 130C 130F 00000000h RO; R/W Channel 1 DRAM Timing Register 0 C1DRT0 1310 1313 34B10461h RO; R/W Channel 1 DRAM Timing Register 1 C1DRT1 1314 1317 11E08463h RO; R/W Channel 1 DRAM Timing Register 2 C1DRT2 1318 131B 2200105Fh RO; R/W Channel 1 DRAM Timing Register 3 C1DRT3 131C 131F 01056101h RO; R/W Channel 1 DRAM Timing Register 4 C1DRT4 1320 1323 29503C32h RO; R/W Channel 1 DRAM timing register 5 C1DRT5 1324 1327 62C32020h R/W; RO 1328 132B 29503C32h RO; R/W Reserved Datasheet Register Start Channel 1 DRAM Controller Mode 0 C1DRC0 1330 1333 40000002h RO; R/W Channel 1 DRAM Controller Mode 1 C1DRC1 1334 1337 00000000h RO; R/W Channel 1 DRAM Controller Mode 2 C1DRC2 1338 133B 00000000h RO; R/W 279 Device 0 Memory Mapped I/O Register Register Name Register Symbol Reserved C1AIT Channel 1 Adaptive Idle Timer Control Reserved Register End 133C 134F 1350 1357 1358 136B Default Value Access 0000000000 000000h RO; R/W Channel 1 (G)MCH Throttling Event Weight 1 C1DTEW1 136C 136F 00000000h RO; R/W Channel 1 (G)MCH Throttling Event Weight C1GTEW 1370 1373 00000000h R/W/L Channel 1 (G)MCH Throttling Control C1GTC 1374 1377 00000000h R/W/L; RO Channel 1 DRAM Rank Throttling Passive Event C1DTPEW 1378 137F 0000000000 000000h RO; R/W/L Channel 1 DRAM Rank Throttling Active Event C1DTAEW 1380 1387 0000000000 000000h RO; R/W/L Channel 1 DRAM Throttling Control C1DTC 1388 138B 00000000h R/W/L; RO 138C 13AF Reserved 19.7.1 Register Start C0DRB01 - Channel 0 DRAM Rank Boundary 0/1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1200-1203h 00000000h RO; R/W 32 bits The DRAM Rank Boundary Register defines the upper boundary address of each DRAM rank with a granularity of 32. These registers are used to determine which chip select will be active for a given address. In all modes, if a DIMM is single-sided, it appears as a populated rank and an empty rank. A DRB must be programmed appropriately for each. 280 Bit Access Default Value 31:25 RO 00h Description Reserved Datasheet Device 0 Memory Mapped I/O Register Bit Access Default Value 24:16 R/W 000h Description Channel 0 DRAM Rank 1 Boundary Address (DRB1): This 9-bit value defines the upper and lower addresses for each DRAM rank. Bits 7:2 are compared against Address 32:27 to determine the upper address limit of a particular rank. Bits 1:0 must be 0's. 15:9 RO 00h 8:0 R/W 000h Reserved Channel 0 DRAM Rank 0 Boundary Address (DRB0): This 9-bit value defines the upper and lower addresses for each DRAM rank. Bits 7:2 are compared against Address 32:27 to determine the upper address limit of a particular rank. Bits 1:0 must be 0's. Datasheet 281 Device 0 Memory Mapped I/O Register 19.7.2 C0DRB23 - Channel 0 DRAM Rank Boundary 2/3 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1204-1207h 00000000h RO; R/W 32 bits . 282 Bit Access Default Value 31:0 RO 00000000h Description Reserved Datasheet Device 0 Memory Mapped I/O Register 19.7.3 C0DRA - Channel 0 DRAM Rank 0,1 Attribute B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1208-120Bh 00000000h RO; R/W 32 bits The DRAM Rank Attribute Registers define the page sizes to be used when accessing different ranks. These registers should be left with their default value (all zeros) for any rank that is unpopulated, as determined by the corresponding CxDRB registers. Each byte of information in the CxDRA registers describes the page size of a pair of ranks. Bit Access Default Value Description 31:22 RO 00h Reserved 21 RO 0b Reserved 20:19 R/W 00b Rank 1 Bank Architecture: 00: 4 Bank 01: 8 Bank 10 - 11: Reserved 18 RO 0b 17:16 R/W 00b Reserved Rank 0 Bank Architecture: 00: 4 Bank 01: 8 Bank 10 - 11: Reserved 15:7 RO 6:4 R/W Reserved 000b Channel 0 DRAM Odd Rank 1 Attribute (DRA1): This 3-bit field defines the page size of the corresponding rank. 000: Unpopulated 001: Reserved 010: 4 KB 011: 8 KB Others: Reserved 3 RO 0b 2:0 R/W 000b Reserved Channel 0 DRAM Even Rank 0 Attribute (DRA0): This 3-bit field defines the page size of the corresponding rank. 000: Unpopulated 001: Reserved 010: 4 KB 011: 8 KB Others: Reserved Datasheet 283 Device 0 Memory Mapped I/O Register 19.7.4 C0DCLKDIS - Channel 0 DRAM Clock Disable B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 120C-120Fh 00000000h RO; R/W 32 bits This register can be used to disable the System Memory Clock signals to each DIMM slot, which can significantly reduce EMI and Power concerns for clocks that go to unpopulated DIMMs. Clocks should be enabled based on whether a slot is populated, and what kind of DIMM is present: Since there are multiple clock signals assigned to each rank of a DIMM, it is important to clarify exactly which rank width field affects which clock signal. Channel Rank Clocks 0 0 or 1 1 2 or 3 Bit Access Default Value 31:4 RO 0000000h 3 R/W 0b Affected SM_CK_1:0 SM_CK_4:3 Description Reserved DIMM Clock Gate Enable Pair 3: 0: Tri-state the corresponding clock pair. 1: Enable the corresponding clock pair. 2 R/W 0b DIMM Clock Gate Enable Pair 2: 0: Tri-state the corresponding clock pair. 1: Enable the corresponding clock pair. 1 R/W 0b DIMM Clock Gate Enable Pair 1: 0: Tri-state the corresponding clock pair. 1: Enable the corresponding clock pair. 0 R/W 0b DIMM Clock Gate Enable Pair 0: 0: Tri-state the corresponding clock pair. 1: Enable the corresponding clock pair. 284 Datasheet Device 0 Memory Mapped I/O Register 19.7.5 C0DRT0 - Channel 0 DRAM Timing Register 0 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1210-1213h 34B10461h R/W; RO 32 bits This 32-bit register defines the timing parameters for all devices in this channel. The BIOS programs this register with the "least common denominator" values for each channel after reading configuration registers of each device in each channel. Bit Access Default Value 31 RO 0b 30:26 R/W 0dh Description Reserved Back to Back Write to Precharge Command Spacing (same bank) (B2BWR2PCSB): This field determines the number of clocks between write command and a subsequent precharge command to the same bank. The minimum number of clocks is calculated based on this formula DDR2: DDR2: WL+ BL/2 + t WR 0h to 9h: Reserved Ah to 13h: Allowed NOTE: Write Recovery time (tWR). Write recovery time is a standard DDRI/II timing parameter that determines minimum time between a write command and a subsequent precharge command to the same bank. This parameter is programmable on DDR-II DIMMs and the value used above must match the largest delay programmed in any DIMM in the system. Minimum recommended values are documented below: tWR (on CK) 4 Clocks: DDR2 533 5 Clocks: DDR2 667 25:24 Datasheet RO 00b Reserved 285 Device 0 Memory Mapped I/O Register Bit Access Default Value 23:20 R/W Bh Description Back-to-Back Write to Read Command Spacing (Same Rank): This field determines the number of clocks between write command and a subsequent read command to the same rank. The minimum number of clocks is calculated based on this formula: DDR2: WL + BL/2 + t WTR 0h - 7h: Reserved 8h - Fh: Allowed NOTE: Write to Read Command delay (tWTR). The tWTR is a standard DDR timing parameter and is used to time a RD command after a WR command to the same row. Following are the values used for tWTR 2 Clocks - CL = DDR2 533 3 Clocks - DDR2 667 19:18 RO 00b 17:15 R/W 010b Reserved Back to Back Write-Read Command Spacing (Different Rank): This field determines the number of turnaround clocks on the data bus that needs to be inserted between write command and a subsequent read command. The minimum spacing of commands is calculated based on the formula: Spacing = BL/2 + TA (wr-rd) + WL - CL BL is the burst length which is 8 TA is the required write to read DQ turnaround on the bus. Can be set to 1,2, or 3 CK using this register CL is CAS Latency WL is Write Latency Encoding 14 286 RO 0b BL8 CMD Spacing 110 9 101 8 100 7 011 6 010 5 001 4 000 3 Reserved Datasheet Device 0 Memory Mapped I/O Register Bit Access Default Value 13:10 R/W 1h Description Back-to-Back Read-Write Command Spacing: This field determines the number of turnaround clocks between the read command and a subsequent write command. Same and different rank The minimum spacing of commands is calculated based on the formula: Spacing = CL + BL/2 + TA (wr-rd) - WL BL is the burst length which is 8 TA is the required read to write DQ turnaround on the bus. Can be set to 1,2,3, 4 CK for DDR2 CL is CAS Latency WL is Write Latency Encoding BL8 CMD Spacing 0111 12 0110 11 0101 10 0100 9 0011 8 0010 7 0001 6 0000 5 The bigger turnarounds are used in large configurations, where the difference in total channel delay between the fastest and slowest DIMM is large. 9:8 RO 00b 7:5 R/W 011b Reserved Back-to-back Write Command Spacing (Different Rank): This field controls the turnaround time on the DQ bus for WRWR sequence to different ranks in one channel. The minimum spacing of commands is calculated based on the formula DDR2 = BL/2 + TA Encoding Spacing Turnaround BL8 CMD 100 4 turnaround clocks on DQ 8 011 3 turnaround clocks on DQ 7 010 2 turnaround clocks on DQ 6 001 1 turnaround clocks on DQ 5 000 0 turnaround clocks on DQ 4 The bigger turnarounds are used in large configurations, where the difference in total channel delay between the fastest and slowest DIMM is large. 4:3 Datasheet RO 00b Reserved 287 Device 0 Memory Mapped I/O Register Bit Access Default Value 2:0 R/W 001b Description Back-to-Back Read Command Spacing (Different Rank): This field controls the turnaround time on the DQ bus for RdRD sequence to different ranks in one channel. The minimum spacing of commands is calculated based on the formula DDR2 = BL/2 + TA Encoding Spacing Turnaround BL8 CMD 101 6 turnaround clocks on DQ 10 100 5 turnaround clocks on DQ 9 011 4 turnaround clocks on DQ 8 010 3 turnaround clocks on DQ 7 001 2 turnaround clocks on DQ 6 000 1 turnaround clocks on DQ 5 The bigger turnarounds are used in large configurations, where the difference in total channel delay between the fastest and slowest DIMM is large. 19.7.6 C0DRT1 - Channel 0 DRAM Timing Register 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1214-1217h 11E08463h RO; R/W 32 bits Bit Access Default Value Description 31:30 RO 00b Reserved 29:28 R/W 01b Read to Precharge (tRTP): These bits control the number of clocks that are inserted between a read command to a row precharge command to the same rank. Encoding tRTP 00: BL/2 (DDR2 533) 01: BL/2+1 (DDR2 667) 10: Reserved 11: Reserved 27:26 RO 00b Reserved 25:21 R/W 0Fh Activate to Precharge Delay (tRAS): This bit controls the number of DRAM clocks for tRAS. Minimum recommendations are beside their corresponding encodings. Recommended values: 288 0Ch: DDR2 533 0Fh: DDR2 667 Datasheet Device 0 Memory Mapped I/O Register Bit Access Default Value 20:19 RO 00b 18 R/W 0b Description Reserved Precharge to Precharge Delay: Control Pre to Pre delay between the different banks of the same rank. 0: 1 Clock 1: 2 Clock 17:16 RO 00b 15 R/W 1b Reserved Pre-All to Activate Delay (tRPALL): This is applicable only to 8-bank architectures. Must be set to 1 if any Rank is populated with 8-bank device technology. 0: tRPALL = tRP 1: tRPALL = tRP + 1 14:13 RO 00b 12:10 R/W 001b Reserved Activate to Activate delay (tRRD): Control Act to Act delay between the different banks of the same rank. Trr is specified in "ns". 10 ns for 2-KB page size and 7.5 ns for 1-KB page size. Bios should round up to the nearest number of clocks and use the maximum applicable value. 000 = 2 Clock 001 = 3 Clock 010 = 4 Clocks 011 = 5 Clocks 100 = 6 Clocks 9:8 RO 00b 7:5 R/W 011b Reserved DRAM RASB to CASB Delay (tRCD): This bit controls the number of clocks inserted between a row activate command and a read or write command to that row. Encoding 4:3 Datasheet RO 00b tRCD 000 2 DRAM Clocks 001 3 DRAM Clocks 010 4 DRAM Clocks 011 5 DRAM Clocks 100 6 DRAM Clocks 101 7 DRAM Clocks 110 8 DRAM Clocks. 111 Reserved Reserved 289 Device 0 Memory Mapped I/O Register Bit Access Default Value 2:0 R/W 011b Description DRAM RASB Precharge (tRP): This bit controls the number of clocks that are inserted between a row precharge command and an activate command to the same rank. Encoding tRP 000: 2 DRAM Clocks. 001: 3 DRAM Clocks 010: 4 DRAM Clocks 011: 5 DRAM Clocks 100: 6 DRAM clocks 101: 7 DRAM clocks. 110: 111: 290 8 DRAM clocks Reserved Datasheet Device 0 Memory Mapped I/O Register 19.7.7 C0DRT2 - Channel 0 DRAM Timing Register 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1218-121Bh 2200105Fh RO; R/W 32 bits Bit Access Default Value Description 31:29 R/W 001b Reserved 28:27 RO 00b Reserved 26:24 R/W 010b CKE Deassert Duration: 000 = Reserved 001 = Reserved 010 = 3 clocks 011 = 4 clocks 100 = 5 clocks 101 - 111 = Reserved Must be set to 010 for DDR2 23:22 RO 00b Reserved 21:17 R/W 00h Rolling Activate Window (tFAW): Number of clks in a rolling activate window. A rolling activate window allows only 4 activates to a given rank in that window of time. 0-6 - Reserved 7-1B - Allowed 1C-1F - Reserved 16:15 RO 0h Reserved 14:12 R/W 1h Fast Exit Active / Precharge Power Down to Any Command (tXP): Power down exit time is tracked from the clock in which we sample CKE active, after exit from dynamic power down, until the clock which we drive a command (ACT/PRE/RD/WR). Following are the options provided. 001 = Power Down Exit time is set to 2 clocks. (DDR2 533, DDR2 667). Others = Reserved 11:10 Datasheet RO 0h Reserved 291 Device 0 Memory Mapped I/O Register Bit Access Default Value 9:6 R/W 1h Description Slow Exit Precharge Power Down Exit to Read / Write CS# (tXPDLL): Power down exit time is tracked from the clock in which we sample CKE active, after exit from dynamic power down, until the clock which we drive a command (ACT/PRE/RD/WR). Following are the options provided. 0001 = Power Down Exit time is set to 2 clocks. (DDR2 533, DDR2 667) Others = Reserved 19.7.8 5 RO 0h Reserved 4:0 R/W 1Fh Reserved C0DRT3 - Channel 0 DRAM Timing Register 3 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 121C-121Fh 01056101h RO; R/W 32 bits Note: If the existing fields does not support the required delay time, then these values have to be counted in half frequency clocks instead of full freq clocks. Bit Access Default Value Description 31:30 RO 00b Reserved 29:28 R/W 00b Reserved 27:26 R/W 00b Self Refresh Exit to Non-Read Write Command (tXS): 00 = tRFC + 10 clocks 01 = tRFC + 20 clocks 10 = value in[29:28] - (trfc + 20) clocks 11 = reserved 25:23 R/W 010b CASB Latency (tCL): This value is programmable on DDR2 DIMMs. The value programmed here must match the CAS Latency of every DDR2 DIMM in the system. Encoding 000 3 001 4 010 5 011 6 100 101 22:21 292 RO 00b DDR2 CL 7 Reserved Reserved Datasheet Device 0 Memory Mapped I/O Register Bit Access Default Value 20:13 R/W 2Bh Description Refresh Cycle Time (tRFC): Refresh cycle time is measured from a Refresh command (REF) until the first Activate command (ACT) to the same rank, required to perform a read or write. For DDR2 on Mobile Intel(R) 965 Express chipset , tRFC needs to follow the values recommended in the table below:- Parameter 256 Mb 512 Mb 75 ns 105 ns 127.5 ns 195 ns DDR2 533 20 (mem clks) 28 (mem clks) 34 (mem clks) 52 (mem clks) DDR2 677 25 (mem clks) 35 (mem clks) 43 (mem clks) 65 (mem clks) Refresh to Active/ Refresh Command Time 12:11 RO 00b Reserved 10:7 R/W 2h Reserved 6:3 RO 0h Reserved 2:0 R/W 001b Sym tRFC 1 Gb 2 Gb Write Latency (tWL): For DDR2 this register is programmed to CL -1 000 - 2 - DDR2 - CL3 001 - 3 - DDR2 - CL4 010 - 4 - DDR2 - CL5 011 - 5 - DDR2 - CL6 100 - 6 - DDR2 - CL7 100 - 7 - DDR2 - CL8 Others are Reserved Datasheet 293 Device 0 Memory Mapped I/O Register 19.7.9 C0DRT4 - Channel 0 DRAM Timing Register 4 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR Chipset 1220-1223h 29503C32h RO; R/W 32 bits If the existing fields does not support the required delay time, then these values have to be counted in half freq clocks instead of full freq clocks. Bit Access Default Value 31:27 R/W 05h Description DIMM Clock Stability Timer: Number of clocks to wait after a self refresh exit before asserting CKE to bring the DIMMs out of self refresh 26:17 R/W 0A8h Master DLL Lock Timer: This is the time taken for the master DLL in the Write, RCVEN and the DQS buffer to lock. This value must be programmed by BIOS based on memory controller clock (mdclk) freq and the DLL lock time requirements. 16 RO 0h Reserved 15:10 R/W 0Fh IO Pad Reset Time: This is the number of clocks taken for all of the system memory buffers to reset when the IOPADRST is deasserted. This value must be programmed by the BIOS based on the memory controller clock frequency (one fourth of DDR rate). 9 RO 0h 8:0 R/W 032h Reserved Write Slave DLL Lock Timer: This is the time taken for the Slave DLL in the Write, RCVEN and the DQS buffer to lock. This value must be programmed by BIOS based on memory controller clock freq and the DLL lock time requirements. 294 Datasheet Device 0 Memory Mapped I/O Register 19.7.10 C0DRT5 - Channel 0 DRAM Timing Register 5 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR Chipset 1224-1227h 62C32020h RO; R/W 32 bits Bit Access Default Value Description 31:28 R/W 6h Reserved 27:26 RO 00b Reserved 25:22 R/W Bh TS Read Delay: Time taken for the TS read data to come back from the MPR register in the DRAM Min Time := BL/2 + CL + 2 21 RO 0b 20:12 R/W 032h Reserved Read Slave DLL Lock Timer: This is the time taken for the Slave DLL in the Write, RCVEN and the DQS buffer to lock. This value must be programmed by BIOS based on memory controller clock freq and the DLL lock time requirements. 11 RO 0b Reserved 10:8 R/W 000b Reserved 7:4 R/W 2h Read Diff Amp Select (DIFFAMPSEL): The number of whole memory clocks to wait after sending a read command before asserting DIFFAMP. Datasheet 3 R/W 0b 2:1 R/W 00b 0 R/W 0b Reserved DQ / DQS Sense Amp Duration Reserved 295 Device 0 Memory Mapped I/O Register 19.7.11 C0DRC0 - Channel 0 DRAM Controller Mode 0 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1230-1233h 40000002h RO; R/W 32 bits Bit Access Default Value 31:30 RO 01b 29 R/W 0b Description Reserved Initialization Complete (IC): This bit is used for communication of software state between the memory controller and the BIOS. BIOS sets this bit to 1 after initialization of the DRAM memory array is complete. 28 RO 0b Reserved 27:24 RO 0h Reserved 23:22 RO 0h Reserved 21:20 RO 00b Reserved 19:18 RO 00b Reserved 17 RO 0h Reserved 16 R/W 0h Address/Control Assertion Rule (ACAR): Defines the number of clock cycles the MA, RASB, CASB, WEB are asserted. 0: always 2n rule (address and CMD are driven the clock prior to CSB assertion) 1: always 1n Rule (address and CMD are always driven on the same clock as CSB) 15 RO 0h Reserved 14 RO 0b Reserved 13:11 RO 0h Reserved 10:8 R/W 000b Refresh Mode Select (RMS): This field determines whether refresh is enabled and, if so, at what rate refreshes will be executed. 010: Refresh enabled. Refresh interval 7.8 sec 011: Refresh enabled. Refresh interval 3.9 sec Other: Reserved 7 RO 0h 6:4 R/W 000b Reserved Mode Select (SMS): These bits select the special operational mode of the DRAM interface. The special modes are intended for initialization at power up. 000: Post Reset state. When the (G)MCH exits reset (power-up or otherwise), the mode select field is cleared to "000". 296 Datasheet Device 0 Memory Mapped I/O Register Bit Access Default Value Description During any reset sequence, while power is applied and reset is active, the (G)MCH deasserts all CKE signals. After internal reset is deasserted, CKE signals remain deasserted for some time (minimum 35us) and then are asserted. During suspend, (G)MCH internal signal triggers DRAM controller to flush pending commands and enter all ranks into Self-Refresh mode. As part of resume sequence, (G)MCH will be reset - which will clear this bit field to "000" and maintain CKE signals deasserted. After internal reset is deasserted, CKE signals remain deasserted until this field is written to a value different than "000". On this event, all CKE signals are asserted. During entry to other low power states (C3, S1), (G)MCH internal signal triggers DRAM controller to flush pending commands and enter all ranks into Self-Refresh mode. During exit to normal mode, (G)MCH signal triggers DRAM controller to exit Self-Refresh and resume normal operation without S/W involvement. 001: NOP Command Enable - All CPU cycles to DRAM result in a NOP command on the DRAM interface. 010: All Banks Pre-charge Enable - All CPU cycles to DRAM result in an "all banks precharge" command on the DRAM interface. 011: Mode Register Set Enable - All CPU cycles to DRAM result in a "mode register" set command on the DRAM interface. Host address lines are mapped to DRAM address lines in order to specify the command sent. Host address lines [12:3] are mapped to MA[9:0], and HA[13] is mapped to MA[11]. For DDR2 MA[6:4] need to be driven based on the value programmed in the Additive Latency field. Additive Latency MA[5:3] 0.0 Clocks 000 1.0 Clocks 001 2.0 Clocks 010 3.0 Clocks 011 4.0 Clocks 100 MA[10] must be set to 0 to enable DQSB strobe complements. For the remaining bit fields, refer to the JEDEC spec for DDR-II. 101: Reserved 110: CBR Refresh Enable: In this mode all CPU cycles to DRAM result in a CBR cycle on the DRAM interface 111: Normal operation 3 R/W 0b Burst Length (BL): The burst length is the number of QWORDS returned by a DIMM per read command, when not interrupted. This bit is used to select the DRAM controller's Burst Length operation mode. It must be set to match to the behavior of the DIMM. 1: Burst Length of 8 Datasheet 297 Device 0 Memory Mapped I/O Register Bit Access Default Value 2 RO 0h 1:0 RO 10b Description Reserved DRAM Type (DT): Used to select between supported SDRAM types. 10: Second Revision Dual Data Rate (DDR2) SDRAM Other: Reserved 298 Datasheet Device 0 Memory Mapped I/O Register 19.7.12 C0DRC1 - Channel 0 DRAM Controller Mode 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1234-1237h 00000000h RO; R/W 32 bits Bit Access Default Value Description 31:28 R/W 0h Reserved 27 RO 0b Reserved 26:24 R/W 000b Reserved 23:20 RO 0h Reserved 19:16 R/W 0h CKE Tri-state Enable Per Rank: Bit 16 corresponds to rank 0 0: CKE is not tri-stated. 1: CKE is tri-stated. This is set only if the Rank is physically not populated. 15:13 RO 000b 12 R/W 0b Reserved CS# Tri-state Enable (CSBTRIEN): When set to a 1, the DRAM the controller will tri-state CS# when the corresponding CKE is deasserted. 0: Address Tri-state Disabled 1: Address Tri-state Enabled 11 R/W 0b Address Tri-state Enable (ADRTRIEN): When set to a 1, the DRAM controller will tri-state the MA, CMD, and CSB (CSB if lines only when all CKEs are deasserted. CKEs deassert based on Idle timer or max rank count control. 0: Address Tri-state Disabled 1: Address Tri-state Enabled Datasheet 10:7 RO 0h Reserved 6 R/W 0b Reserved 5:4 RO 00b Reserved 3 R/W 0b Reserved 2:0 RO 000b Reserved 299 Device 0 Memory Mapped I/O Register 19.7.13 C0DRC2 - Channel 0 DRAM Controller Mode 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1238-123Bh 00000000h RO; R/W 32 bits Bit Access Default Value Description 31:28 RO 0h Reserved 27:24 R/W 0h DRAM ODT Tri-state Enable Per Rank: Bit 24 corresponds to rank 0 0: ODT is not tri-stated. 1: ODT is tri-stated. This is set only if the Rank is physically not populated. 23:14 RO 000h 13 R/W 0b Reserved Clock Control to DQ Buffers: 0: Clocks to DQ buffers are on for reads. 1: Clocks to DQ buffers are off for reads. Clock does not need to run once the first read or write to this channel has occurred. BIOS will set this bit once it has done the first read from this channel. 19.7.14 12 R/W 0b Reserved 11:9 RO 000b Reserved 8:0 RO 000h Reserved C0AIT - Channel 0 Adaptive Idle Timer Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1250-1257h 0000000000000000h RO; R/W 64 bits This register controls Characteristics of Adaptive Idle Timer Mechanism. This register bit field shall contain the default value unless otherwise indicated in the BIOS Specification. 300 Datasheet Device 0 Memory Mapped I/O Register 19.7.15 C0DTEW1 - Channel 0 (G)MCH Throttling Event Weight 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 126C-126Fh 00000000h RO; R/W 32 bits This register contains programmable Event weights that are input into the averaging filter. Bit Access Default Value 31:16 RO 0000h 15:8 R/W 00h Description Reserved Toggle Write Event Weight: This value is input to the filter if, in a given clock, a data write toggle assertion is detected 7:0 R/W 00h Toggle Read Event Weight: This value is input to the filter if, in a given clock, a data read toggle assertion is detected Datasheet 301 Device 0 Memory Mapped I/O Register 19.7.16 C0GTEW - Channel 0 (G)MCH Throttling Event Weight B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1270-1273h 00000000h R/W/L 32 bits This register contains programmable Event weights that are input into the averaging filter. Each Event weight is a normalized 8-bit value that the BIOS must program. The BIOS must account for burst length, 1N/2N rule considerations. It is also possible for BIOS to take into account type loading variations of memory caused as a function of memory types and population of ranks. Bit Access Default Value 31:24 R/W/L 00h Description Read Weight: This value is input to the filter if in a given clock there is a valid read command being issued on the memory bus. 23:16 R/W/L 00h Write Weight: This value is input to the filter if in a given clock there is a valid write command being issued on the memory bus. 15:8 R/W/L 00h Command Weight: This value is input to the filter if in a given clock there is a valid command other than a read or a write being issued on the memory bus. 7:0 R/W/L 00h Idle Weight: This value is input to the filter if in a given clock there is no command being issued on the memory bus. If command and address are tri-stated a value of 0 is input to the filter. If command and address are under reduced drive strength after this value is divided by 2 and input to the filter. 302 Datasheet Device 0 Memory Mapped I/O Register 19.7.17 C0GTC - Channel 0 (G)MCH Throttling Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1274-1277h 00000000h R/W/L; RO 32 bits This register contains programmable Event weights that are input into the averaging filter. Each Event weight is a normalized 8-bit value that the BIOS must program. The BIOS must account for burst length, 1N/2N rule considerations. It is also possible for BIOS to take into account type loading variations of memory caused as a function of memory types and population of ranks. Bit Access Default Value 31 R/W/L 0b Description (G)MCH Throttle Lock (GTLOCK): This bit secures the (G)MCH throttling control registers GTEW, GTC and TSWDT. This bit defaults to 0. Once a 1 is written to this bit, all of the configuration register bits are read-only. 30 RO 0b Reserved 29 R/W/L 0b Reserved 28:25 RO 0h Reserved 24:22 R/W/L 000b Reserved 21 R/W/L 0b (G)MCH Bandwidth Based Throttling Enable: 0: Bandwidth Threshold (WAB) is not used for throttling. 1: Bandwidth Threshold (WAB) is used for throttling. If both bandwidth based and thermal sensor based throttling modes are on and the thermal sensor trips, the thermal threshold is used for throttling. 20 R/W/L 0b (G)MCH Thermal Sensor Trip Enable: 0: (G)MCH throttling is not initiated when the (G)MCH thermal sensor trips. 1: (G)MCH throttling is initiated when the (G)MCH thermal sensor trips and the Filter output is equal to or exceeds thermal threshold WAT. 19 RO 0b Reserved 18:16 R/W/L 000b Reserved 15:8 R/W/L 00h WAB: Threshold allowed per clock for bandwidth based throttling. (G)MCH does not allow transactions to proceed on the DDR bus if the output of the filter equals or exceeds this value. 7:0 R/W/L 00h WAT: Threshold allowed per clock during thermal sensor enabled throttling. (G)MCH does not allow transactions to proceed on the DDR bus if the output of the filter equals or exceeds this value. Datasheet 303 Device 0 Memory Mapped I/O Register 19.7.18 C0DTPEW - Channel 0 DRAM Rank Throttling Passive Event B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1278-127Fh 0000000000000000h RO; R/W/L 64 bits This register contains programmable Event weights that are input into the averaging filter. Each Event weight is a normalized 8-bit value that the BIOS must program. The BIOS must account for burst length, 1N/2N rule considerations. It is also possible for BIOS to take into account type loading variations of memory caused as a function of memory types and population of ranks. (G)MCH implements 4 independent filters, one per rank. All bits in this register can be locked by the DTLOCK bit in the C0DTC register. Bit Access Default Value 63:48 RO 0000h 47:40 R/W/L 00h Description Reserved Additive Weight for ODT: This value is added to the total weight of a Rank if ODT on that rank is asserted. Note that this value should reflect whether the DRAMs have been programmed for 75- or 150- termination. 39:32 R/W/L 00h Weight for Any Open Page during Active (WAOPDA): This value is input to the filter if, during the present clock, the corresponding rank has any pages open and is not in power down. The value programmed here is IDD3N from the JEDEC. 31:24 R/W/L 00h All Banks Precharge Active (ABPA): This value is input to the filter if, during the present clock, the corresponding rank has all banks precharged but is not in power down. The value programmed here is IDD2N from the JEDEC spec. 23:16 R/W/L 00h Weight for Any Open Page during Power Down (WAOPDPD): This value is input to the filter if, during the present clock, the corresponding rank is in power down with pages open. The value programmed here is IDD3P from the JEDEC. 15:8 R/W/L 00h All Banks Precharge Power Down (ABPPD): This value is input to the filter if, during the present clock, the corresponding rank has all banks precharged and is powered down. The value programmed here is IDD2P from the JEDEC spec. 7:0 R/W/L 00h Self Refresh: This value is input to the filter if in a clock the corresponding rank is in self refresh. 304 Datasheet Device 0 Memory Mapped I/O Register 19.7.19 C0DTAEW - Channel 0 DRAM Rank Throttling Active Event B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1280-1287h 0000000000000000h RO; R/W/L 64 bits This register contains programmable Event weights that are input into the averaging filter. Each Event weight is a normalized 8-bit value that the BIOS must program. The BIOS must account for burst length, 1N/2N rule considerations. It is also possible for BIOS to take into account type loading variations of memory caused as a function of memory types and population of ranks. (G)MCH implements 4 independent filters, one per rank. In the clock (G)MCH asserts a command to the DRAM (via CS# assertion) based on the command type the one of the weights specified in this register is added to the weight specified in the previous register and input to the filter. Datasheet Bit Access Default Value Description 63:56 RO 00h Read with AP 55:48 RO 00h Write with AP 47:40 R/W/L 00h Read 39:32 R/W/L 00h Write 31:24 R/W/L 00h Precharge - All 23:16 R/W/L 00h Precharge 15:8 R/W/L 00h Activate 7:0 R/W/L 00h Refresh 305 Device 0 Memory Mapped I/O Register 19.7.20 C0DTC - Channel 0 DRAM Throttling Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1288-128Bh 00000000h R/W/L; RO 32 bits This register is for programmable Event weights that are input into the averaging filter. Each Event weight is a normalized 8-bit value that the BIOS must program. The Bios must account for burst length, 1N/2N rule considerations. It is also possible for bios to take into account type loading variations of memory caused as a function of memory types and population of ranks. Bit Access Default Value 31 R/W/L 0b Description DRAM Throttle Lock (DTLOCK): This bit secures the DRAM throttling control registers DT*EW and DTC. This bit defaults to 0. Once a 1 is written to this bit, all of the configuration register bits are read-only. 30 RO 0b Reserved 29 R/W/L 0b Reserved 28:25 RO 0h Reserved 24:22 R/W/L 000b Reserved 21 R/W/L 0b (G)MCH Bandwidth Based Throttling Enable: 0: Bandwidth Threshold (WAB) is not used for throttling. 1: Bandwidth Threshold (WAB) is used for throttling. If both bandwidth based and thermal sensor based throttling modes are on and the thermal sensor trips, the thermal threshold is used for throttling. 20 R/W/L 0b (G)MCH Thermal Sensor Trip Enable: 0: (G)MCH throttling is not initiated when the (G)MCH thermal sensor trips. 1: (G)MCH throttling is initiated when the (G)MCH thermal sensor trips and the Filter output is equal to or exceeds thermal threshold WAT. 19 RO 0b 18:16 R/W/L 000b Reserved Time Constant: 000: 2^28 Clocks 001: 2^29 Clocks 010: 2^30 Clocks 011: 2^31 Clocks 1XX: Reserved 306 Datasheet Device 0 Memory Mapped I/O Register Bit Access Default Value 15:8 R/W/L 00h Description WAB: Threshold allowed per clock for bandwidth based throttling. (G)MCH does not allow transactions to proceed on the DDR bus if the output of the filter equals or exceeds this value. 7:0 R/W/L 00h WAT: Threshold allowed per clock during for thermal sensor enabled throttling. (G)MCH does not allow transactions to proceed on the DDR bus if the output of the filter equals or exceeds this value. 19.7.21 C1DRB01 - Channel 1 DRAM Rank Boundary 0/1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1300-1303h 00000000h RO; R/W 32 bits The operation of this register is detailed in the description for register C0DRB01. 19.7.22 C1DRB23 - Channel 1 DRAM Rank Boundary 2/3 B/D/F/Type: Address Offset: Default Value: Access: Size: 19.7.23 0/0/0/MCHBAR 1304-1307h 00000000h RO; R/W 32 bits Bit Access Default Value 31:0 RO 00h Description Reserved C1DRA - Channel 1 DRAM Rank 0,1 Attribute B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1308-130Bh 00000000h RO; R/W 32 bits The operation of this register is detailed in the description for register C0DRA. Datasheet 307 Device 0 Memory Mapped I/O Register 19.7.24 C1DCLKDIS - Channel 1 DRAM Clock Disable B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 130C-130Fh 00000000h RO; R/W 32 bits The operation of this register is detailed in the description for register C0DCLKDIS. 19.7.25 C1DRT0 - Channel 1 DRAM Timing Register 0 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR Chipset 1310-1313h 34B10461h RO; R/W 32 bits The operation of this register is detailed in the description for register C0DRT0. 19.7.26 C1DRT1 - Channel 1 DRAM Timing Register 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1314-1317h 11E08463h RO; R/W 32 bits The operation of this register is detailed in the description for register C0DRT1. 19.7.27 C1DRT2 - Channel 1 DRAM Timing Register 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1318-131Bh 2200105Fh RO; R/W 32 bits The operation of this register is detailed in the description for register C0DRT2. 19.7.28 C1DRT3 - Channel 1 DRAM Timing Register 3 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR Chipset 131C-131Fh 01056101h RO; R/W 32 bits The operation of this register is detailed in the description for register C0DRT3. 308 Datasheet Device 0 Memory Mapped I/O Register 19.7.29 C1DRT4 - Channel 1 DRAM Timing Register 4 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR Chipset 1320-1323h 29503C32h RO; R/W 32 bits The operation of this register is detailed in the description for register C0DRT4. 19.7.30 C1DRT5 - Channel 1 DRAM timing register 5 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR Chipset 1324-1327h 62C32020h R/W; RO 32 bits The operation of this register is detailed in the description for register C0DRT5. 19.7.31 C1DRC0 - Channel 1 DRAM Controller Mode 0 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1330-1333h 40000002h R/W; RO 32 bits The operation of this register is detailed in the description for register C0DRC0. 19.7.32 C1DRC1 - Channel 1 DRAM Controller Mode 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR Chipset 1334-1337h 00000000h R/W; RO 32 bits The operation of this register is detailed in the description for register C0DRC1. 19.7.33 C1DRC2 - Channel 1 DRAM Controller Mode 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR Chipset 1338-133Bh 00000000h RO; R/W 32 bits The operation of this register is detailed in the description for register C0DRC2. Datasheet 309 Device 0 Memory Mapped I/O Register 19.7.34 C1AIT - Channel 1 Adaptive Idle Timer Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1350-1357h 0000000000000000h R/W; RO 64 bits This register controls Characteristics of Adaptive Idle Timer Mechanism. The operation of this register is detailed in the description for register C0AIT. 19.7.35 C1DTEW1 - Channel 1 (G)MCH Throttling Event Weight 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 136C-136Fh 00000000h R/W; RO 32 bits The operation of this register is detailed in the description for register C0DTEW1. 19.7.36 C1GTEW - Channel 1 (G)MCH Throttling Event Weight B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1370-1373h 00000000h R/W/L 32 bits The operation of this register is detailed in the description for register C0GTEW. 19.7.37 C1GTC - Channel 1 (G)MCH Throttling Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1374-1377h 00000000h R/W/L; RO 32 bits The operation of this register is detailed in the description for register C0GTC. 19.7.38 C1DTPEW - Channel 1 DRAM Rank Throttling Passive Event B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1378-137Fh 0000000000000000h RO; R/W/L 64 bits The operation of this register is detailed in the description for register C0DTPEW. 310 Datasheet Device 0 Memory Mapped I/O Register 19.7.39 C1DTAEW - Channel 1 DRAM Rank Throttling Active Event B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1380-1387h 0000000000000000h RO; R/W/L 64 bits The operation of this register is detailed in the description for register C0DTAEW. 19.7.40 C1DTC - Channel 1 DRAM Throttling Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/MCHBAR 1388-138Bh 00000000h R/W/L; RO 32 bits The operation of this register is detailed in the description for register C0DTC. 19.8 DMI RCRB This section describes the mapped register for DMI. The DMIBAR register, described in Section 18.1.17 provides the base address or these registers. This Root Complex Register Block (RCRB) controls (G)MCH -ICH8M serial interconnect. An RCRB is required for configuration and control of element that are located internal to root complex that are not directly associated with a PCI Express device. The base address of this space is programmed in DMIBAR in Device 0 config space. Note: All RCRB register spaces needs to remain organized as they are here. The Virtual Channel capabilities (or at least the first PCI Express Extended Capability) must begin at the 0h offset of the 4-K area pointed to by the associated BAR. This is a PCI Express 1.0 specification requirement. Datasheet Register Name Register Symbol Register Start Register End Default Value Access DMI Virtual Channel Enhanced Capability DMIVCECH 0 3 04010002h RO DMI Port VC Capability Register 1 DMIPVCCAP1 4 7 00000001h RO; R/WO DMI Port VC Capability Register 2 DMIPVCCAP2 8 B 00000001h RO DMI Port VC Control DMIPVCCTL C D 0000h RO; R/W 311 Device 0 Memory Mapped I/O Register Register Name Register Symbol Reserved Register End E F Default Value Access DMI VC0 Resource Capability DMIVC0RCAP 10 13 00000001h RO DMI VC0 Resource Control DMIVC0RCTL0 14 17 800000FFh RO; R/W 18 19 Reserved DMI VC0 Resource Status DMIVC0RSTS 1A 1B 0002h RO DMI VC1 Resource Capability DMIVC1RCAP 1C 1F 00008001h RO DMI VC1 Resource Control DMIVC1RCTL1 20 23 01000000h RO; R/W 24 25 26 27 0002h RO 28 3F Reserved DMI VC1 Resource Status DMIVC1RSTS Reserved DMI Root Complex Link Declaration DMIRCLDECH 40 43 08010005h RO DMI Element Self Description DMIESD 44 47 01000202h RO; R/WO 48 4F 50 53 00000000h R/WO; RO 54 57 Reserved DMI Link Entry 1 Description DMILE1D Reserved DMI Link Entry 1 Address DMILE1A 58 5F 00000000000 00000h RO; R/WO DMI Link Entry 2 Description DMILE2D 60 63 00000000h RO; R/WO 64 67 68 6F 00000000000 00000h RO; R/WO Reserved DMI Link Entry 2 Address 312 Register Start DMILE2A Datasheet Device 0 Memory Mapped I/O Register Register Name Register Symbol Reserved 19.8.1 Register Start Register End 70 83 Default Value Access DMI Link Capabilities DMILCAP 84 87 00012C41h RO; R/WO DMI Link Control DMILCTL 88 89 0000h RO; R/W DMI Link Status DMILSTS 8A 8B 0001h RO DMIVCECH - DMI Virtual Channel Enhanced Capability B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 0-3h 04010002h RO 32 bits This register indicates DMI Virtual Channel capabilities. Bit Access Default Value 31:20 RO 040h Description Pointer to Next Capability (PNC): This field contains the offset to the next PCI Express capability structure in the linked list of capabilities (Link Declaration Capability). 19:16 RO 1h PCI Express Virtual Channel Capability Version (PCIEVCCV): Hardwired to 1 to indicate compliances with the 1.0 version of the PCI Express specification. 15:0 RO 0002h Extended Capability ID (ECID): Value of 0002h identifies this linked list item (capability structure) as being for PCI Express Virtual Channel registers. Datasheet 313 Device 0 Memory Mapped I/O Register 19.8.2 DMIPVCCAP1 - DMI Port VC Capability Register 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 4-7h 00000001h RO; R/WO 32 bits Describes the configuration of PCI Express Virtual Channels associated with this port. Bit Access Default Value 31:7 RO 0000000h 6:4 RO 000b Description Reserved Low Priority Extended VC Count (LPEVCC): Indicates the number of (extended) Virtual Channels in addition to the default VC belonging to the low-priority VC (LPVC) group that has the lowest priority with respect to other VC resources in a strict-priority VC Arbitration. The value of 0 in this field implies strict VC arbitration. 3 RO 0b 2:0 R/WO 001b Reserved Extended VC Count (EVCC): Indicates the number of (extended) Virtual Channels in addition to the default VC supported by the device. The Private Virtual Channel is not included in this count. 19.8.3 DMIPVCCAP2 - DMI Port VC Capability Register 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 8-Bh 00000001h RO 32 bits Describes the configuration of PCI Express Virtual Channels associated with this port. Bit Access Default Value Description 31:24 RO 00h Reserved 23:8 RO 0000h Reserved 7:0 RO 01h VC Arbitration Capability (VCAC): Indicates that the only possible VC arbitration scheme is hardware fixed (in the root complex). VC1 is the highest priority. 314 Datasheet Device 0 Memory Mapped I/O Register 19.8.4 DMIPVCCTL - DMI Port VC Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR C-Dh 0000h RO; R/W 16 bits Bit Access Default Value Description 15:4 RO 000h Reserved 3:1 R/W 000b VC Arbitration Select (VCAS): This field will be programmed by software to the only possible value as indicated in the VC Arbitration Capability field. The value 000b when written to this field will indicate the VC arbitration scheme is hardware fixed (in the root complex). This field cannot be modified when more than one VC in the LPVC group is enabled. 000: Hardware fixed arbitration scheme, for example, Round Robin. Others: Reserved See the PCI express specification for more details. 0 19.8.5 RO 0b Reserved DMIVC0RCAP - DMI VC0 Resource Capability B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 10-13h 00000001h RO 32 bits Bit Access Default Value Description 31:24 RO 00h Reserved 23 RO 0b Reserved 22:16 RO 00h Reserved 15 RO 0b Reject Snoop Transactions (REJSNPT): 0: Transactions with or without the No Snoop bit set within the TLP header are allowed on this VC. 1: Any transaction without the No Snoop bit set within the TLP header will be rejected as an Unsupported Request. 14:8 RO 00h Reserved 7:0 RO 01h Port Arbitration Capability (PAC): Having only bit 0 set indicates that the only supported arbitration scheme for this VC is non-configurable hardwarefixed. Datasheet 315 Device 0 Memory Mapped I/O Register 19.8.6 DMIVC0RCTL0 - DMI VC0 Resource Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 14-17h 800000FFh RO; R/W 32 bits Controls the resources associated with PCI Express Virtual Channel 0. Bit Access Default Value 31 RO 1b Description Virtual Channel 0 Enable (VC0E): For VC0 this is hardwired to 1 and read only as VC0 can never be disabled. 30:27 RO 0h 26:24 RO 000b Reserved Virtual Channel 0 ID (VC0ID): Assigns a VC ID to the VC resource. For VC0 this is hardwired to 0 and read only. 23:20 RO 0h 19:17 R/W 000b Reserved Port Arbitration Select (PAS): Configures the VC resource to provide a particular Port Arbitration service. Valid value for this field is a number corresponding to one of the asserted bits in the Port Arbitration Capability field of the VC resource. Because only bit 0 of that field is asserted. 16:8 RO 000h 7:1 R/W 7Fh Reserved Traffic Class / Virtual Channel 0 Map (TCVC0M): Indicates the TCs (Traffic Classes) that are mapped to the VC resource. Bit locations within this field correspond to TC values. For example, when bit 7 is set in this field, TC7 is mapped to this VC resource. When more than one bit in this field is set, it indicates that multiple TCs are mapped to the VC resource. In order to remove one or more TCs from the TC/VC Map of an enabled VC, software must ensure that no new or outstanding transactions with the TC labels are targeted at the given Link. 0 RO 1b Traffic Class 0 / Virtual Channel 0 Map (TC0VC0M): Traffic Class 0 is always routed to VC0. 316 Datasheet Device 0 Memory Mapped I/O Register 19.8.7 DMIVC0RSTS - DMI VC0 Resource Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 1A-1Bh 0002h RO 16 bits This register reports the Virtual Channel specific status. Bit Access Default Value 15:2 RO 0000h 1 RO 1b Description Reserved Virtual Channel 0 Negotiation Pending (VC0NP): 0:The VC negotiation is complete. 1:The VC resource is still in the process of negotiation (initialization or disabling). This bit indicates the status of the process of Flow Control initialization. It is set by default on Reset, as well as whenever the corresponding Virtual Channel is Disabled or the Link is in the DL_Down state. It is cleared when the link successfully exits the FC_INIT2 state. BIOS Requirement: Before using a Virtual Channel, software must check whether the VC Negotiation Pending fields for that Virtual Channel are cleared in both Components on a Link. 0 Datasheet RO 0b Reserved 317 Device 0 Memory Mapped I/O Register 19.8.8 DMIVC1RCAP - DMI VC1 Resource Capability B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 1C-1Fh 00008001h RO; 32 bits Bit Access Default Value Description 31:24 RO 00h Reserved 23 RO 0b Reserved 22:16 RO 00h Reserved 15 RO 1b Reject Snoop Transactions (REJSNPT): 0: Transactions with or without the No Snoop bit set within the TLP header are allowed on this VC. 1: Any transaction without the No Snoop bit set within the TLP header will be rejected as an Unsupported Request. 14:8 RO 00h Reserved 7:0 RO 01h Port Arbitration Capability (PAC): Having only bit 0 set indicates that the only supported arbitration scheme for this VC is non-configurable hardwarefixed. 318 Datasheet Device 0 Memory Mapped I/O Register 19.8.9 DMIVC1RCTL1 - DMI VC1 Resource Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 20-23h 01000000h R/W; RO 32 bits Controls the resources associated with PCI Express Virtual Channel 1. Bit Access Default Value 31 R/W 0b Description Virtual Channel 1 Enable (VC1E): 0: Virtual Channel is disabled. 1: Virtual Channel is enabled. See exceptions below. Software must use the VC Negotiation Pending bit to check whether the VC negotiation is complete. When VC Negotiation Pending bit is cleared, a 1 read from this VC Enable bit indicates that the VC is enabled (Flow Control Initialization is completed for the PCI Express port). A 0 read from this bit indicates that the Virtual Channel is currently disabled. BIOS Requirement: 1. To enable a Virtual Channel, the VC Enable bits for that Virtual Channel must be set in both Components on a Link. 2. To disable a Virtual Channel, the VC Enable bits for that Virtual Channel must be cleared in both Components on a Link. 3. Software must ensure that no traffic is using a Virtual Channel at the time it is disabled. 4. Software must fully disable a Virtual Channel in both Components on a Link before re-enabling the Virtual Channel. 30:27 RO 0h 26:24 R/W 001b Reserved Virtual Channel 1 ID (VC1ID): Assigns a VC ID to the VC resource. Assigned value must be non-zero. This field can not be modified when the VC is already enabled. 23:20 RO 0h 19:17 R/W 000b Reserved Port Arbitration Select (PAS): Configures the VC resource to provide a particular Port Arbitration service. Valid value for this field is a number corresponding to one of the asserted bits in the Port Arbitration Capability field of the VC resource. 16:8 Datasheet RO 000h Reserved 319 Device 0 Memory Mapped I/O Register Bit Access Default Value 7:1 R/W 00h Description Traffic Class / Virtual Channel 1 Map (TCVC1M): Indicates the TCs (Traffic Classes) that are mapped to the VC resource. Bit locations within this field correspond to TC values. For example, when bit 7 is set in this field, TC7 is mapped to this VC resource. When more than one bit in this field is set, it indicates that multiple TCs are mapped to the VC resource. In order to remove one or more TCs from the TC/VC Map of an enabled VC, software must ensure that no new or outstanding transactions with the TC labels are targeted at the given Link. 0 RO 0b Traffic Class 0 / Virtual Channel 1 Map (TC0VC1M): Traffic Class 0 is always routed to VC0. 19.8.10 DMIVC1RSTS - DMI VC1 Resource Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 26-27h 0002h RO 16 bits This register reports the Virtual Channel specific status. Bit Access Default Value 15:2 RO 0000h 1 RO 1b Description Reserved Virtual Channel 1 Negotiation Pending (VC1NP): 0: The VC negotiation is complete. 1: The VC resource is still in the process of negotiation (initialization or disabling). Software may use this bit when enabling or disabling the VC. This bit indicates the status of the process of Flow Control initialization. It is set by default on Reset, as well as whenever the corresponding Virtual Channel is Disabled or the Link is in the DL_Down state. It is cleared when the link successfully exits the FC_INIT2 state. Before using a Virtual Channel, software must check whether the VC Negotiation Pending fields for that Virtual Channel are cleared in both Components on a Link. 0 320 RO 0b Reserved Datasheet Device 0 Memory Mapped I/O Register 19.8.11 DMIRCLDECH - DMI Root Complex Link Declaration B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 40-43h 08010005h RO 32 bits This capability declares links from the respective element to other elements of the root complex component to which it belongs and to an element in another root complex component. Bit Access Default Value 31:20 RO 080h Description Pointer to Next Capability (PNC): This field contains the offset to the next PCI Express capability structure in the linked list of capabilities (Internal Link Control Capability). 19:16 RO 1h Link Declaration Capability Version (LDCV): Hardwired to 1 to indicate compliances with the 1.0 version of the PCI Express specification. 15:0 RO 0005h Extended Capability ID (ECID): Value of 0005 h identifies this linked list item (capability structure) as being for PCI Express Link Declaration Capability. Datasheet 321 Device 0 Memory Mapped I/O Register 19.8.12 DMIESD - DMI Element Self Description B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 44-47h 01000202h RO; R/WO 32 bits This register provides information about the root complex element containing this Link Declaration Capability. Bit Access Default Value 31:24 RO 01h Description Port Number (PORTNUM): Specifies the port number associated with this element with respect to the component that contains this element. This port number value is utilized by the egress port of the component to provide arbitration to this Root Complex Element. 23:16 R/WO 00h Component ID (CID): Identifies the physical component that contains this Root Complex Element. BIOS Requirement: Must be initialized according to guidelines in the PCI Express* Isochronous/Virtual Channel Support Hardware Programming Specification (HPS). 15:8 RO 02h Number of Link Entries (NLE): Indicates the number of link entries following the Element Self Description. This field reports 2 (one for (G)MCH egress port to main memory and one to egress port belonging to ICH on other side of internal link). 7:4 RO 0h Reserved 3:0 RO 2h Element Type (ETYP): Indicates the type of the Root Complex Element. Value of 2 h represents an Internal Root Complex Link (DMI). 322 Datasheet Device 0 Memory Mapped I/O Register 19.8.13 DMILE1D - DMI Link Entry 1 Description B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 50-53h 00000000h R/WO; RO 32 bits This register is the first part of a Link Entry which declares an internal link to another Root Complex Element. Bit Access Default Value 31:24 R/WO 00h Description Target Port Number (TPN): Specifies the port number associated with the element targeted by this link entry (egress port of ICH). The target port number is with respect to the component that contains this element as specified by the target component ID. This can be programmed by BIOS, but the default value will likely be correct because the DMI RCRB in the ICH will likely be associated with the default egress port for the ICH meaning it will be assigned port number 0. 23:16 R/WO 00h Target Component ID (TCID): Identifies the physical component that is targeted by this link entry. BIOS Requirement: Must be initialized according to guidelines in the PCI Express* Isochronous/Virtual Channel Support Hardware Programming Specification (HPS). 15:2 RO 0000h 1 RO 0b Reserved Link Type (LTYP): Indicates that the link points to memory-mapped space (for RCRB). The link address specifies the 64-bit base address of the target RCRB. 0 R/WO 0b Link Valid (LV): 0: Link Entry is not valid and will be ignored. 1: Link Entry specifies a valid link. Datasheet 323 Device 0 Memory Mapped I/O Register 19.8.14 DMILE1A - DMI Link Entry 1 Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 58-5Fh 0000000000000000h RO; R/WO 64 bits This register is the second part of a Link Entry which declares an internal link to another Root Complex Element. Bit Access Default Value 63:32 RO 00000000h 31:12 R/WO 00000h Description Reserved Link Address (LA): Memory mapped base address of the RCRB that is the target element (egress port of ICH) for this link entry. 11:0 324 RO 000h Reserved Datasheet Device 0 Memory Mapped I/O Register 19.8.15 DMILE2D - DMI Link Entry 2 Description B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 60-63h 00000000h RO; R/WO 32 bits This register is the first part of a Link Entry which declares an internal link to another Root Complex Element. Bit Access Default Value 31:24 RO 00h Description Target Port Number (TPN): Specifies the port number associated with the element targeted by this link entry (Egress Port). The target port number is with respect to the component that contains this element as specified by the target component ID. 23:16 R/WO 00h Target Component ID (TCID): Identifies the physical or logical component that is targeted by this link entry. Must be initialized according to guidelines in the PCI Express* Isochronous/Virtual Channel Support Hardware Programming Specification (HPS). 15:2 RO 0000h 1 RO 0b Reserved Link Type (LTYP): Indicates that the link points to memory-mapped space (for RCRB). The link address specifies the 64-bit base address of the target RCRB. 0 R/WO 0b Link Valid (LV): 0: Link Entry is not valid and will be ignored. 1: Link Entry specifies a valid link. Datasheet 325 Device 0 Memory Mapped I/O Register 19.8.16 DMILE2A - DMI Link Entry 2 Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 68-6Fh 0000000000000000h RO; R/WO 64 bits This register is the second part of a Link Entry which declares an internal link to another Root Complex Element. Bit Access Default Value 63:32 RO 00000000h 31:12 R/WO 00000h Description Reserved Link Address (LA): Memory mapped base address of the RCRB that is the target element (Egress Port) for this link entry. 11:0 326 RO 000h Reserved Datasheet Device 0 Memory Mapped I/O Register 19.8.17 DMILCAP - DMI Link Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 84-87h 00012C41h RO; R/WO 32 bits This register indicates DMI specific capabilities. Bit Access Default Value 31:18 RO 0000h 17:15 R/WO 010b Description Reserved L1 Exit Latency (L1SELAT): Indicates the length of time this Port requires to complete the transition from L1 to L0. The value 010 b indicates the range of 2 s to less than 4 s. 000: Less than 1 s 00: 1 s to less than 2 s 010: 2 s to less than 4 s 011: 4 s to less than 8 s 100: 8 s to less than 16 s 101: 16 s to less than 32 s 110: 32 s-64 s 111: More than 64 s Both bytes of this register that contain a portion of this field must be written simultaneously in order to prevent an intermediate (and undesired) value from ever existing. 14:12 R/WO 010b L0s Exit Latency (L0SELAT): Indicates the length of time this Port requires to complete the transition from L0s to L0. 000: Less than 64 ns 001: 64 ns to less than 128 ns 010: 128 ns to less than 256 ns 011: 256 ns to less than 512 ns 100: 512 ns to less than 1 s 101: 1 s to less than 2 s 110: 2 s-4 s 111: More than 4 s 11:10 RO 11b Active State Link PM Support (ASLPMS): L0s & L1 entry supported. 9:4 RO 04h Max Link Width (MLW): Indicates the maximum number of lanes supported for this link. 3:0 RO 1h Max Link Speed (MLS): Hardwired to indicate 2.5 Gb/s. Datasheet 327 Device 0 Memory Mapped I/O Register 19.8.18 DMILCTL - DMI Link Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 88-89h 0000h R/W; RO 16 bits This register allows control of DMI. Bit Access Default Value 15:8 RO 00h 7 R/W 0b Description Reserved Extended Synch (EXTSYNC): 0: Standard Fast Training Sequence (FTS). 1: Forces extended transmission of 4096 FTS ordered sets in the L0s state followed by a single SKP Ordered Set prior to entering L0, and the transmission of 1024 TS1 ordered sets in the RecoveryRcvrLock state prior to entering the RecoveryRcvrCfg state. This mode provides external devices monitoring the link time to achieve bit and symbol lock before the link enters L0 state and resumes communication. This is a test mode only and may cause other undesired side effects such as buffer overflows or underruns. 6:3 RO 0000b Reserved 2 R/W 0b Reserved 1:0 R/W 00b Active State Power Management Support (ASPMS): Controls the level of active state power management supported on the given link. 00: 328 Disabled 01: L0s Entry Supported 10: Reserved 11: L0s and L1 Entry Supported Datasheet Device 0 Memory Mapped I/O Register 19.8.19 DMILSTS - DMI Link Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/DMIBAR 8A-8Bh 0001h RO 16 bits This register indicates DMI status. Bit Access Default Value Description 15:10 RO 00h Reserved 9:4 RO 00h Negotiated Width (NWID): Indicates negotiated link width. This field is valid only when the link is in the L0, L0s, or L1 states (after link width negotiation is successfully completed). 0h: Reserved 1h: X1 2h: X2 4h: X4 All other encodings are Reserved 3:0 RO 1h Negotiated Speed (NSPD): Indicates negotiated link speed. 1h: 2.5 Gb/s All other encodings are Reserved Datasheet 329 Device 0 Memory Mapped I/O Register 19.9 Egress Port (EP) RCRB This Root Complex Register Block (RCRB) controls the port arbitration that is based on the PCI Express 1.0 specification. Port arbitration is done for all PCI Express based isochronous requests (always on Virtual Channel 1) before being submitted to the main memory arbiter. The base address of this space is programmed in the EPBAR in Device 0 config space. Register Name Register Symbol Reserved Register End 0 3 Default Value Access EP Port VC Capability Register 1 EPPVCCAP1 4 7 00000401h RO; R/WO EP Port VC Capability Register 2 EPPVCCAP2 8 B 00000001h RO C F Reserved EP VC 0 Resource Capability EPVC0RCAP 10 13 00000001h RO EP VC 0 Resource Control EPVC0RCTL 14 17 800000FFh RO; R/W 18 19 Reserved EP VC 0 Resource Status EPVC0RSTS 1A 1B 0000h RO EP VC 1 Resource Capability EPVC1RCAP 1C 1F 10008010h RO; R/WO EP VC 1 Resource Control EPVC1RCTL 20 23 01080000h R/W; RO; R/W/S 24 25 Reserved 330 Register Start EP VC 1 Resource Status EPVC1RSTS 26 27 0000h RO EP VC 1 Maximum Number of Time Slots EPVC1MTS 28 2B 04050609h R/W EP VC 1 Isoch Timing Control EPVC1ITC 2C 2F 00000000h RO; R/W Datasheet Device 0 Memory Mapped I/O Register Register Name Register Symbol Register Start Register End Default Value Access Reserved EPVC1IWT 30 37 00000000000 00000h R/W EP VC 1 Isoch Slot Time EPVC1IST 38 3F 00000000000 00000h R/W 40 43 44 47 00000201h RO; R/WO 48 4F 50 53 01000000h RO; R/WO 54 57 Reserved EP Element Self Description EPESD Reserved EP Link Entry 1 Description EPLE1D Reserved EP Link Entry 1 Address EPLE1A 58 5F 00000000000 00000h RO; R/WO EP Link Entry 2 Description EPLE2D 60 63 02000002h RO; R/WO EP Link Entry 2 Address EPLE2A 68 6F 00000000000 08000h RO 70 9F 100 11F 00000000000 00000000000 00000000000 00000000000 00000000000 000000000h R/W Reserved Port Arbitration Table Datasheet PORTARB 331 Device 0 Memory Mapped I/O Register 19.9.1 EPPVCCAP1 - EP Port VC Capability Register 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 4-7h 00000401h RO; R/WO 32 bits Describes the configuration of PCI Express Virtual Channels associated with this port. Bit Access Default Value Description 31:12 RO 00000h Reserved 11:8 RO 04h Reserved 7:3 RO 0h Reserved 2:0 R/WO 001b Extended VC Count (EVCC): Indicates the number of (extended) Virtual Channels in addition to the default VC supported by the device. 19.9.2 EPPVCCAP2 - EP Port VC Capability Register 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 8-Bh 00000001h RO 32 bits Describes the configuration of PCI Express Virtual Channels associated with this port. This register bit field shall contain default value unless otherwise indicated in the BIOS Specification. 332 Datasheet Device 0 Memory Mapped I/O Register 19.9.3 EPVC0RCAP - EP VC 0 Resource Capability B/D/F/Type: Address Offset: Default Value: Access: Size: Bit 0/0/0/EPBAR 10-13h 00000001h RO 32 bits Access Default Value 31:16 RO 0000h 15 RO 0b Description Reserved Reject Snoop Transactions (RSNPT): 0: Transactions with or without the No Snoop bit set within the TLP header are allowed on this VC. 1: Any transaction without the No Snoop bit set within the TLP header will be rejected as an Unsupported Request. 14:8 RO 00h Reserved 7:0 RO 01h Port Arbitration Capability (PAC): Indicates types of Port Arbitration supported by this VC 0 resource. Datasheet 333 Device 0 Memory Mapped I/O Register 19.9.4 EPVC0RCTL - EP VC 0 Resource Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 14-17h 800000FFh RO; R/W; 32 bits Controls the resources associated with Egress Port Virtual Channel 0. Bit Access Default Value 31 RO 1b Description VC0 Enable (VC0E): For VC0 this is hardwired to 1 and read only as VC0 can never be disabled. 30:27 RO 0h 26:24 RO 000b Reserved VC0 ID (VC0ID): For VC0 this is hardwired to 0 and read only. 23:20 RO 0h 19:17 RO 000b Reserved Port Arbitration Select (PAS): This field configures the VC resource to provide a particular Port Arbitration service. 16:8 RO 000h 7:1 R/W 7Fh Reserved TC/VC0 Map (TCVC0M): Indicates the TCs (Traffic Classes) that are mapped to the VC resource. 0 334 RO 1b Reserved Datasheet Device 0 Memory Mapped I/O Register 19.9.5 EPVC0RSTS - EP VC 0 Resource Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 1A-1Bh 0000h RO 16 bits This register reports the Virtual Channel specific status. Bit Access Default Value 15:2 RO 0000h 1 RO 0b Description Reserved VC0 Negotiation Pending (VC0NP): 0: The VC negotiation is complete. 1: The VC resource is still in the process of negotiation (initialization or disabling). Before using a Virtual Channel, software must check whether the VC Negotiation Pending fields for that Virtual Channel are cleared in both Components on a Link. 0 19.9.6 RO 0b Reserved EPVC1RCAP - EP VC 1 Resource Capability B/D/F/Type: Address Offset: Default Value: Access: Size: Bit 0/0/0/EPBAR 1C-1Fh 10008010h RO; R/WO 32 bits Access Default Value Description 31:24 RO 10h Reserved 23 RO 0b Reserved 22:16 R/WO 00h Reserved 15 RO 1b Reject Snoop Transactions (RSNPT): 0: Transactions with or without the No Snoop bit set within the TLP header are allowed on this VC. 1: Any transaction without the No Snoop bit set within the TLP header will be rejected as an Unsupported Request. 14:8 RO 00h Reserved 7:0 RO 10h Port Arbitration Capability (PAC): Indicates types of Port Arbitration supported by this VC1 resource. Datasheet 335 Device 0 Memory Mapped I/O Register 19.9.7 EPVC1RCTL - EP VC 1 Resource Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 20-23h 01080000h R/W; RO; R/W/S 32 bits Controls the resources associated with PCI Express Virtual Channel 1. Bit Access Default Value 31 R/W 0b Description VC1 Enable (VC1E): Upon Read after negotiation 0: Virtual Channel is disabled. 1: Virtual Channel is enabled. 30:27 RO 0h 26:24 R/W 001b Reserved VC1 ID (VC1ID): Assigns a VC ID to the VC resource. Assigned value must be non-zero. 23:20 RO 0h 19:17 R/W 100b Reserved Port Arbitration Select (PAS): This field configures the VC resource to provide a particular Port Arbitration service. 16 R/W/S 0b Reserved 15:8 RO 00h Reserved 7:1 R/W 00h TC/VC1 Map (TCVC1M): Indicates the TCs (Traffic Classes) that are mapped to the VC resource. 0 RO 0b TC0/VC1 Map (TC0VC1M): Traffic Class 0 is always routed to VC0. 336 Datasheet Device 0 Memory Mapped I/O Register 19.9.8 EPVC1RSTS - EP VC 1 Resource Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 26-27h 0000h RO 16 bits This register reports the Virtual Channel specific status. Bit Access Default Value 15:2 RO 0000h 1 RO 0b Description Reserved VC1 Negotiation Pending (VC1NP): 0: The VC negotiation is complete. 1: The VC resource is still in the process of negotiation (initialization or disabling). Before using a Virtual Channel, software must check whether the VC Negotiation Pending fields for that Virtual Channel are cleared in both Components on a Link. 0 19.9.9 RO 0b Reserved EPVC1MTS - EP VC 1 Maximum Number of Time Slots B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 28-2Bh 04050609h R/W 32 bits The fields in this register reflect the maximum number of time slots supported by the (G)MCH for various configurations. This register bit field shall contain the default value unless otherwise indicated in BIOS specification. 19.9.10 EPVC1ITC - EP VC 1 Isoch Timing Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 2C-2Fh 00000000h RO; R/W 32 bits This register reflects the number of common host clocks (Hclks) per time slot. This register bit field shall contain the default value unless otherwise indicated in BIOS specification. Datasheet 337 Device 0 Memory Mapped I/O Register 19.9.11 EPVC1IST - EP VC 1 Isoch Slot Time B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 38-3Fh 0000000000000000h R/W 64 bits This register reflects the number of common host clocks per time slot. This register bit field shall contain the default value unless otherwise indicated in BIOS specification. 19.9.12 EPESD - EP Element Self Description B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 44-47h 00000201h RO; R/WO 32 bits This register provides information about the root complex element containing this link declaration capability. Bit Access Default Value 31:24 RO 00h Description Port Number (PN): This field specifies the port number associated with this element with respect to the component that contains this element. Value of 00h indicates to configuration software that this is the default egress port. 23:16 R/WO 00h Component ID (CID): Identifies the physical component that contains this Root Complex Element. 15:8 RO 02h Number of Link Entries (NLE): Indicates the number of link entries following the Element Self Description. This field reports 2 (one each for PCIe and DMI). 7:4 RO 0h Reserved 3:0 RO 1h Element Type (ET): Indicates the type of the Root Complex Element. Value of 1h represents a port to system memory. 338 Datasheet Device 0 Memory Mapped I/O Register 19.9.13 EPLE1D - EP Link Entry 1 Description B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 50-53h 01000000h RO; R/WO 32 bits This register is the first part of a Link Entry which declares an internal link to another Root Complex Element. Bit Access Default Value 31:24 RO 01h Description Target Port Number (TPN): Specifies the port number associated with the element targeted by this link entry (DMI). The target port number is with respect to the component that contains this element as specified by the target component ID. 23:16 R/WO 00h Target Component ID (TCID): Identifies the physical or logical component that is targeted by this link entry. 15:2 RO 0000h 1 RO 0b Reserved Link Type (LTYP): Indicates that the link points to memory-mapped space (for RCRB). The link address specifies the 64-bit base address of the target RCRB (Root Complex Register Block) 0 R/WO 0b Link Valid (LV): 0: Link Entry is not valid and will be ignored. 1: Link Entry specifies a valid link. Datasheet 339 Device 0 Memory Mapped I/O Register 19.9.14 EPLE1A - EP Link Entry 1 Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 58-5Fh 0000000000000000h RO; R/WO 64 bits This register is the second part of a Link Entry which declares an internal link to another Root Complex Element. Bit Access Default Value 63:32 RO 00000000h 31:12 R/WO 00000h Description Reserved Link Address (LA): Memory mapped base address of the RCRB that is the target element (DMI) for this link entry. 11:0 340 RO 000h Reserved Datasheet Device 0 Memory Mapped I/O Register 19.9.15 EPLE2D - EP Link Entry 2 Description B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 60-63h 02000002h RO; R/WO 32 bits This register is the first part of a Link Entry which declares an internal link to another Root Complex Element. Bit Access Default Value 31:24 RO 02h Description Target Port Number (TPN): Specifies the port number associated with the element targeted by this link entry (PEG). The target port number is with respect to the component that contains this element as specified by the target component ID. 23:16 R/WO 00h Target Component ID (TCID): Identifies the physical or logical component that is targeted by this link entry. A value of 0 is reserved. Component IDs start at 1. This value is a mirror of the value in the Component ID field of all elements in this component. 15:2 RO 0000h 1 RO 1b Reserved Link Type (LTYP): Indicates that the link points to configuration space of the integrated device which controls the x16 root port. The link address specifies the configuration address (Segment, Bus, Device, Function) of the target root port. 0 R/WO 0b Link Valid (LV): 0: Link Entry is not valid and will be ignored. 1: Link Entry specifies a valid link. Datasheet 341 Device 0 Memory Mapped I/O Register 19.9.16 EPLE2A - EP Link Entry 2 Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/0/0/EPBAR 68-6Fh 0000000000008000h RO 64 bits This register is the second part of a Link Entry which declares an internal link to another Root Complex Element. Bit Access Default Value 63:28 RO 00000000 0h 27:20 RO 00h 19:15 RO 00001b Description Reserved Bus Number (BUSN) Device Number (DEVN): Target for this link is PCI Express x16 port (Device 1). 19.9.17 14:12 RO 000b Function Number (FUNN) 11:0 RO 000h Reserved PORTARB - Port Arbitration Table B/D/F/Type: 0/0/0/EPBAR Address Offset: 100-11Fh Default Value: 0000000000000000000000000000000000000000000000000000000000000000h Access: R/W Size: 256 bits The Port Arbitration Table register is a read-write register array used to store the arbitration table for Port Arbitration of the Egress Port VC resource. The register bit field shall contain the default values otherwise indicated in BIOS Specification. 342 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Device 1 contains the controls associated with the x16 root port that is the intended attach point for external graphics. It is typically referred to as PEG (PCI Express Graphics) port. It also functions as the virtual PCI-to-PCI Bridge that was previously associated with AGP. Warning: When reading the PCI Express "conceptual" registers such as these, you may not get a valid value unless the register value is stable. The PCI Express Specification defines two types of reserved bits: * Reserved and Preserved: Reserved for future RW implementations; software must preserve value read for writes to these bits. * Reserved and Zero: Reserved for future R/WC/S implementations; software must use 0 for writes to these bits. Unless explicitly documented as Reserved and Zero, all bits marked as Reserved are part of the Reserved and Preserved type which has historically been the typical definition for Reserved. Most (if not all) control bits in this device cannot be modified unless the link is down. Software is required to first disable the link, then program the registers, then reenable the link (which will cause a full-retrain with the new settings). Datasheet 343 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1 PEG Device 1 Function 0 Configuration Registers Summary Register Name Register Symbol Register End Default Value Access Vendor Identification VID1 0 1 8086h Device Identification DID1 2 3 2A01h1 RO PCI Command PCICMD1 4 5 0000h RO; R/W PCI Status PCISTS1 6 7 0010h RO; R/WC Revision Identification RID1 8 8 00h RO Class Code CC1 9 B 060400h RO Cache Line Size CL1 C C 00h R/W Header Type HDR1 E E 01h RO F 17 RO 2 2A11h Reserved Primary Bus Number PBUSN1 18 18 00h RO Secondary Bus Number SBUSN1 19 19 00h R/W Subordinate Bus Number SUBUSN1 1A 1A 00h R/W 1B 1B Reserved 344 Register Start I/O Base Address IOBASE1 1C 1C F0h RO; R/W I/O Limit Address IOLIMIT1 1D 1D 00h RO; R/W Secondary Status SSTS1 1E 1F 0000h R/WC; RO Memory Base Address MBASE1 20 21 FFF0h RO; R/W Memory Limit Address MLIMIT1 22 23 0000h RO; R/W Prefetchable Memory Base Address PMBASE1 24 25 FFF1h RO; R/W Prefetchable Memory Limit Address PMLIMIT1 26 27 0001h RO; R/W Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Register Name Register Symbol Register End Default Value Access Prefetchable Memory Base Address PMBASEU1 28 2B 0000000Fh R/W Prefetchable Memory Limit Address PMLIMITU1 2C 2F 00000000h R/W 30 33 34 34 88h RO 35 3B Reserved Capabilities Pointer CAPPTR1 Reserved Interrupt Line INTRLINE1 3C 3C 00h R/W Interrupt Pin INTRPIN1 3D 3D 01h RO Bridge Control BCTRL1 3E 3F 0000h RO; R/W 40 7F Reserved Power Management Capabilities PM_CAPID1 80 83 C8039001h RO Power Management Control/Status PM_CS1 84 87 00000000h RO; R/W/S; R/W Subsystem ID and Vendor ID Capabilities SS_CAPID 88 8B 0000800Dh RO Subsystem ID and Subsystem Vendor ID SS 8C 8F 00008086h R/WO Message Signaled Interrupts Capability ID MSI_CAPID 90 91 A005h RO Message Control MC 92 93 0000h RO; R/W Message Address MA 94 97 00000000h RO; R/W Message Data MD 98 99 0000h R/W 9A 9F Reserved Datasheet Register Start PCI Express-G Capability List PEG_CAPL A0 A1 0010h RO PCI Express-G Capabilities PEG_CAP A2 A3 0141h RO; R/WO Device Capabilities DCAP A4 A7 00008000h RO 345 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Register Name Register Symbol Register Start Register End Default Value Access Device Control DCTL A8 A9 0000h RO; R/W Device Status DSTS AA AB 0000h RO; R/WC Link Capabilities LCAP AC AF 02014D01h RO; R/WO Link Control LCTL B0 B1 0040h RO; R/W Link Status LSTS B2 B3 1001h RO Slot Capabilities SLOTCAP B4 B7 00040000h R/WO; RO Slot Control SLOTCTL B8 B9 01C0h RO; R/W Slot Status SLOTSTS BA BB 0000h RO; R/WC Root Control RCTL BC BD 0000h RO; R/W BE BF C0 C3 00000000h RO; R/WC C4 EB EC EF 00000000h RO; R/W F0 FF Reserved Root Status RSTS Reserved PCI Express-G Legacy Control Reserved PEGLC NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965, GLE960 and GL960 Express Chipsets. 2. Valid for the Mobile Intel GME965 Express Chipset only. 346 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.1 VID1 - Vendor Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 0-1h 8086h RO 16 bits This register combined with the Device Identification register to uniquely identify any PCI device. Bit Access Default Value 15:0 RO 8086h Description Vendor Identification (VID1): PCI standard identification for Intel. 20.1.2 DID1 - Device Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 2-3h 2A01h RO 16 bits This register combined with the Vendor Identification register uniquely identifies any PCI device. Bit Access Default Value Description 15:0 RO 2A01h1 Device Identification Number (DID1): 2A11h2 Identifier assigned to the (G)MCH Device 1 ( virtual PCI-to-PCI bridge, PCI Express Graphics port ). NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965, GLE960, and GL960 Express Chipsets. 2. Valid for the Mobile Intel GME965 Chipset only. Datasheet 347 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.3 PCICMD1 - PCI Command B/D/F/Type: Address Offset: Default Value: Access: Size: Bit 0/1/0/PCI 4-5h 0000h RO; R/W; 16 bits Access Default Value 15:11 RO 00h 10 R/W 0b Description Reserved INTA Assertion Disable (INTAAD): 0: This device is permitted to generate INTA interrupt messages. 1: This device is prevented from generating interrupt messages. Any INTA emulation interrupts already asserted must be deasserted when this bit is set. Only affects interrupts generated by the device (PCI INTA from a PME or Hot Plug event) controlled by this command register. It does not affect upstream MSIs, upstream PCI INTA-INTD assert and deassert messages. 9 RO 0b Fast Back-to-Back Enable (FB2B): Hardwired to 0. 8 R/W 0b SERR Message Enable (SERRE1): Controls Device 1 SERR messaging. The (G)MCH communicates the SERRB condition by sending an SERR message to the ICH. This bit, when set, enables reporting of non-fatal and fatal errors detected by the device to the Root Complex. Note that errors are reported if enabled either through this bit or through the PCI-Express specific bits in the Device Control Register 0: The SERR message is generated by the (G)MCH for Device 1 only under conditions enabled individually through the Device Control Register. 1: The (G)MCH is enabled to generate SERR messages which will be sent to the ICH for specific Device 1 error conditions generated/detected on the primary side of the virtual PCI to PCI bridge (not those received by the secondary side). The status of SERRs generated is reported in the PCISTS1 register. 7 RO 0b Reserved 6 R/W 0b Parity Error Enable (PERRE): Controls whether or not the Master Data Parity Error bit in the PCI Status register can bet set. 0: Master Data Parity Error bit in PCI Status register can NOT be set. 1: Master Data Parity Error bit in PCI Status register CAN be set. 5 RO 0b VGA Palette Snoop (VGAPS): Not Applicable or Implemented. Hardwired to 0. 348 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Bit 4 Access Default Value RO 0b Description Memory Write and Invalidate Enable (MWIE): Not Applicable or Implemented. Hardwired to 0. 3 RO 0b Special Cycle Enable (SCE): Not Applicable or Implemented. Hardwired to 0. 2 R/W 0b Bus Master Enable (BME): Controls the ability of the PEG port to forward Memory and IO Read/Write Requests in the upstream direction. 0: This device is prevented from making memory or IO requests to its primary bus. Note that according to PCI Specification, as MSI interrupt messages are in-band memory writes, disabling the bus master enable bit prevents this device from generating MSI interrupt messages or passing them from its secondary bus to its primary bus. Upstream memory writes/reads, IO writes/reads, peer writes/reads, and MSIs will all be treated as illegal cycles. Writes are forwarded to memory address 0 with byte enables deasserted. Reads will be forwarded to memory address 0 and will return Unsupported Request status (or Master abort) in its completion packet. 1: This device is allowed to issue requests to its primary bus. Completions for previously issued memory read requests on the primary bus will be issued when the data is available. This bit does not affect forwarding of Completions from the primary interface to the secondary interface. 1 R/W 0b Memory Access Enable (MAE): 0: All of Device 1's memory space is disabled. 1: Enable the Memory and Prefetchable memory address ranges defined in the MBASE1, MLIMIT1, PMBASE1, and PMLIMIT1 registers. 0 R/W 0b IO Access Enable (IOAE): 0: All of Device 1's I/O space is disabled. 1: Enable the I/O address range defined in the IOBASE1, and IOLIMIT1 registers. Datasheet 349 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.4 PCISTS1 - PCI Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 6-7h 0010h RO; R/WC 16 bits This register reports the occurrence of error conditions associated with primary side of the "virtual" Host-PCI Express bridge embedded within the (G)MCH. Bit Access Default Value 15 RO 0b Description Detected Parity Error (DPE): Not Applicable or Implemented. Hardwired to 0. Parity (generating poisoned TLPs) is not supported on the primary side of this device (we don't do error forwarding). 14 R/WC 0b Signaled System Error (SSE): This bit is set when this device sends an SERR due to detecting an ERR_FATAL or ERR_NONFATAL condition and the SERR Enable bit in the Command register is 1. Both received (if enabled by BCTRL1[1]) and internally detected error messages do not affect this field. 13 RO 0b Received Master Abort Status (RMAS): Not Applicable or Implemented. Hardwired to 0. The concept of a master abort does not exist on primary side of this device. 12 RO 0b Received Target Abort Status (RTAS): Not Applicable or Implemented. Hardwired to 0. The concept of a target abort does not exist on primary side of this device. 11 RO 0b Signaled Target Abort Status (STAS): Not Applicable or Implemented. Hardwired to 0. The concept of a target abort does not exist on primary side of this device. 10:9 RO 00b DEVSELB Timing (DEVT): This device is not the subtractively decoded device on Bus 0. This bit field is therefore hardwired to 00 to indicate that the device uses the fastest possible decode. 8 RO 0b Master Data Parity Error (PMDPE): Because the primary side of the PEG's virtual PCI-to-PCI bridge is integrated with the (G)MCH functionality there is no scenario where this bit will get set. Because hardware will never set this bit, it is impossible for software to have an opportunity to clear this bit or otherwise test that it is implemented. The PCI specification defines it as an R/WC, but for our implementation an RO definition behaves the same way and will meet all Microsoft testing requirements. This bit can only be set when the Parity Error Enable bit in the PCI Command register is set. 7 RO 0b Fast Back-to-Back (FB2B): Not Applicable or Implemented. Hardwired to 0. 350 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Bit Access Default Value Description 6 RO 0b Reserved 5 RO 0b 66-/60-MHz capability (CAP66): Not Applicable or Implemented. Hardwired to 0. 4 RO 1b Capabilities List (CAPL): Indicates that a capabilities list is present. Hardwired to 1. 3 RO 0b INTA Status (INTAS): Indicates that an interrupt message is pending internally to the device. Only PME and Hot Plug sources feed into this status bit (not PCI INTA-INTD assert and deassert messages). The INTA Assertion Disable bit, PCICMD1[10], has no effect on this bit. Note that INTA emulation interrupts received across the link are not reflected in this bit. 2:0 20.1.5 RO 000b Reserved RID1 - Revision Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 8h 00h RO 8 bits This register contains the revision number of the (G)MCH Device 1. These bits are read only and writes to this register have no effect. Bit Access Default Value 7:0 RO 00h Description Revision Identification Number (RID1): This is an 8-bit value that indicates the revision identification number for the (G)MCH. A register swapping mechanism behind RID register is used to select between a single SRID, or a single CRID to be reflected in the RID register. For the C0 stepping SRID= 03h, CRID= 0Ch Datasheet 351 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.6 CC1 - Class Code B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 9-Bh 060400h RO; 24 bits This register identifies the basic function of the device, a more specific sub-class, and a register- specific programming interface. Bit Access Default Value 23:16 RO 06h Description Base Class Code (BCC): Indicates the base class code for this device. This code has the value 06h, indicating a Bridge device. 15:8 RO 04h Sub-Class Code (SUBCC): Indicates the sub-class code for this device. The code is 04h indicating a PCI to PCI Bridge. 7:0 RO 00h Programming Interface (PI): Indicates the programming interface of this device. This value does not specify a particular register set layout and provides no practical use for this device. 20.1.7 CL1 - Cache Line Size B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI Ch 00h R/W 8 bits Bit Access Default Value 7:0 R/W 00h Description Cache Line Size (Scratch Pad): Implemented by PCI Express devices as a read-write field for legacy compatibility purposes but has no impact on any PCI Express device functionality. 352 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.8 HDR1 - Header Type B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI Eh 01h RO; 8 bits This register identifies the header layout of the configuration space. No physical register exists at this location. Bit Access Default Value 7:0 RO 01h Description Header Type Register (HDR): Returns 01 to indicate that this is a single function device with bridge header layout. 20.1.9 PBUSN1 - Primary Bus Number B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 18h 00h RO 8 bits This register identifies that this "virtual" Host-PCI Express Bridge is connected to PCI Bus 0. Bit Access Default Value 7:0 RO 00h Description Primary Bus Number (BUSN): Configuration software typically programs this field with the number of the bus on the primary side of the bridge. Since Device 1 is an internal device and its primary bus is always 0, these bits are read only and are hardwired to 0. Datasheet 353 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.10 SBUSN1 - Secondary Bus Number B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 19h 00h R/W 8 bits This register identifies the bus number assigned to the second bus side of the "virtual" bridge i.e., to PCI Express-G. This number is programmed by the PCI configuration software to allow mapping of configuration cycles to PCI Express-G. Bit Access Default Value 7:0 R/W 00h Description Secondary Bus Number (BUSN): This field is programmed by configuration software with the bus number assigned to PCI Express-G. 20.1.11 SUBUSN1 - Subordinate Bus Number B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 1Ah 00h R/W 8 bits This register identifies the subordinate bus (if any) that resides at the level below PCI Express-G. This number is programmed by the PCI configuration software to allow mapping of configuration cycles to PCI Express-G. Bit Access Default Value 7:0 R/W 00h Description Subordinate Bus Number (BUSN): This register is programmed by configuration software with the number of the highest subordinate bus that lies behind the Device 1 bridge. When only a single PCI device resides on the PCI Express-G segment, this register will contain the same value as the SBUSN1 register. 354 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.12 IOBASE1 - I/O Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 1Ch F0h R/W; RO 8 bits This register controls the CPU to PCI Express-G I/O access routing based on the following formula: IO_BASE=< address =<IO_LIMIT Only upper 4 bits are programmable. For the purpose of address decode address bits A[11:0] are treated as 0. Thus the bottom of the defined I/O address range will be aligned to a 4-KB boundary. Bit Access Default Value 7:4 R/W Fh Description I/O Address Base (IOBASE): Corresponds to A[15:12] of the I/O addresses passed by bridge 1 to PCI Express-G. BIOS must not set this register to 00h otherwise 0CF8h/0CFCh accesses will be forwarded to the PCI Express hierarchy associated with this device. 3:0 Datasheet RO 0h Reserved 355 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.13 IOLIMIT1 - I/O Limit Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 1Dh 00h R/W; RO 8 bits This register controls the CPU to PCI Express-G I/O access routing based on the following formula: IO_BASE=< address =<IO_LIMIT Only upper 4 bits are programmable. For the purpose of address decode address bits A[11:0] are assumed to be FFFh. Thus, the top of the defined I/O address range will be at the top of a 4-KB aligned address block. Bit Access Default Value 7:4 R/W 0h Description I/O Address Limit (IOLIMIT): Corresponds to A[15:12] of the I/O address limit of Device 1. Devices between this upper limit and IOBASE1 will be passed to the PCI Express hierarchy associated with this device. 3:0 20.1.14 RO 0h Reserved SSTS1 - Secondary Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 1E-1Fh 0000h R/WC; RO 16 bits SSTS1 is a 16-bit status register that reports the occurrence of error conditions associated with secondary side (i.e., PCI Express-G side) of the "virtual" PCI-PCI bridge embedded within (G)MCH. Bit Access Default Value 15 R/WC 0b Description Detected Parity Error (DPE): When set indicates that the (G)MCH received across the link (upstream) a Posted Write Data Poisoned TLP (EP=1). 14 R/WC 0b Received System Error (RSE): This bit is set when the secondary side receives an ERR_FATAL or ERR_NONFATAL message due to an error detected by the secondary side, and the SERR Enable bit in the Bridge Control register is 1. 356 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Bit Access Default Value 13 R/WC 0b Description Received Master Abort (RMA): This bit is set when the Secondary Side for Type 1 Configuration Space Header Device (for requests initiated by the Type 1 Header Device itself) receives a Completion with Unsupported Request Completion Status. 12 R/WC 0b Received Target Abort (RTA): This bit is set when the Secondary Side for Type 1 Configuration Space Header Device (for requests initiated by the Type 1 Header Device itself) receives a Completion with Completer Abort Completion Status. 11 RO 0b Signaled Target Abort (STA): Not Applicable or Implemented. Hardwired to 0. The (G)MCH does not generate Target Aborts (the (G)MCH will never complete a request using the Completer Abort Completion status). 10:9 RO 00b DEVSELB Timing (DEVT): Not Applicable or Implemented. Hardwired to 0. 8 R/WC 0b Master Data Parity Error (SMDPE): When set indicates that the (G)MCH received across the link (upstream) a Read Data Completion Poisoned TLP (EP=1). This bit can only be set when the Parity Error Enable bit in the Bridge Control register is set. 7 RO 0b Fast Back-to-Back (FB2B): Not Applicable or Implemented. Hardwired to 0. 6 RO 0b Reserved 5 RO 0b 66-/60-MHz Capability (CAP66): Not Applicable or Implemented. Hardwired to 0. 4:0 Datasheet RO 00h Reserved 357 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.15 MBASE1 - Memory Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 20-21h FFF0h R/W; RO 16 bits This register controls the CPU to PCI Express-G non-prefetchable memory access routing based on the following formula: MEMORY_BASE=< address =<MEMORY_LIMIT The upper 12 bits of the register are read/write and correspond to the upper 12 address bits A[31:20] of the 32 bit address. The bottom 4 bits of this register are read-only and return zeroes when read. This register must be initialized by the configuration software. For the purpose of address decode address bits A[19:0] are assumed to be 0. Thus, the bottom of the defined memory address range will be aligned to a 1-MB boundary. Bit Access Default Value 15:4 R/W FFFh Description Memory Address Base (MBASE): Corresponds to A[31:20] of the lower limit of the memory range that will be passed to PCI Express-G. 3:0 20.1.16 RO 0h Reserved MLIMIT1 - Memory Limit Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 22-23h 0000h R/W; RO 16 bits This register controls the CPU to PCI Express-G non-prefetchable memory access routing based on the following formula: MEMORY_BASE=< address =<MEMORY_LIMIT The upper 12 bits of the register are read/write and correspond to the upper 12 address bits A[31:20] of the 32 bit address. The bottom 4 bits of this register are read-only and return zeroes when read. This register must be initialized by the configuration software. For the purpose of address decode address bits A[19:0] are assumed to be FFFFFh. Thus, the top of the defined memory address range will be at the top of a 1-MB aligned memory block. Note: Memory range covered by MBASE and MLIMIT registers are used to map nonprefetchable PCI Express-G address ranges (typically where control/status memorymapped I/O data structures of the graphics controller will reside) and PMBASE and PMLIMIT are used to map prefetchable address ranges (typically graphics local memory). This segregation allows application of USWC space attribute to be 358 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) performed in a true plug-and-play manner to the prefetchable address range for improved CPU- PCI Express memory access performance. Note: Configuration software is responsible for programming all address range registers (prefetchable, non-prefetchable) with the values that provide exclusive address ranges i.e., prevent overlap with each other and/or with the ranges covered with the main memory. There is no provision in the (G)MCH hardware to enforce prevention of overlap and operations of the system in the case of overlap are not guaranteed. Bit Access Default Value 15:4 R/W 000h Description Memory Address Limit (MLIMIT): Corresponds to A[31:20] of the upper limit of the address range passed to PCI Express-G. 3:0 20.1.17 RO 0h Reserved PMBASE1 - Prefetchable Memory Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 24-25h FFF1h R/W; RO 16 bits This register in conjunction with the corresponding Upper Base Address register controls the CPU to PCI Express-G prefetchable memory access routing based on the following formula: PREFETCHABLE_MEMORY_BASE =< address =< PREFETCHABLE_MEMORY_LIMIT The upper 12 bits of this register are read/write and correspond to address bits A[31:20] of the 40-bit address. The lower 8 bits of the Upper Base Address register are read/write and correspond to address bits A[39:32] of the 40-bit address. This register must be initialized by the configuration software. For the purpose of address decode address bits A[19:0] are assumed to be 0. Thus, the bottom of the defined memory address range will be aligned to a 1-MB boundary. Bit Access Default Value 15:4 R/W FFFh Description Prefetchable Memory Base Address (MBASE): Corresponds to A[31:20] of the lower limit of the memory range that will be passed to PCI Express-G. 3:0 RO 1h 64-bit Address Support: Indicates that the upper 32 bits of the prefetchable memory region base address are contained in the Prefetchable Memory base Upper Address register at 28h. Datasheet 359 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.18 PMLIMIT1 - Prefetchable Memory Limit Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 26-27h 0001h R/W; RO 16 bits This register in conjunction with the corresponding Upper Limit Address register controls the CPU to PCI Express-G prefetchable memory access routing based on the following formula: PREFETCHABLE_MEMORY_BASE =< address =< PREFETCHABLE_MEMORY_LIMIT The upper 12 bits of this register are read/write and correspond to address bits A[31:20] of the 40-bit address. The lower 8 bits of the Upper Limit Address register are read/write and correspond to address bits A[39:32] of the 40-bit address. This register must be initialized by the configuration software. For the purpose of address decode address bits A[19:0] are assumed to be FFFFFh. Thus, the top of the defined memory address range will be at the top of a 1-MB aligned memory block. Note that prefetchable memory range is supported to allow segregation by the configuration software between the memory ranges that must be defined as UC and the ones that can be designated as a USWC (i.e., prefetchable) from the CPU perspective. Bit Access Default Value 15:4 R/W 000h Description Prefetchable Memory Address Limit (PMLIMIT): Corresponds to A[31:20] of the upper limit of the address range passed to PCI Express-G. 3:0 RO 1h 64-Bit Address Support): Indicates that the upper 32 bits of the prefetchable memory region limit address are contained in the Prefetchable Memory Base Limit Address register at 2Ch 360 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.19 PMBASEU1 - Prefetchable Memory Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 28-2Bh 0000000Fh R/W 32 bits The functionality associated with this register is present in the PEG design implementation. This register in conjunction with the corresponding Upper Base Address register controls the CPU to PCI Express-G prefetchable memory access routing based on the following formula: PREFETCHABLE_MEMORY_BASE =< address =< PREFETCHABLE_MEMORY_LIMIT The upper 12 bits of this register are read/write and correspond to address bits A[31:20] of the 40-bit address. The lower 8 bits of the Upper Base Address register are read/write and correspond to address bits A[39:32] of the 40-bit address. This register must be initialized by the configuration software. For the purpose of address decode address bits A[19:0] are assumed to be 0. Thus, the bottom of the defined memory address range will be aligned to a 1-MB boundary. Bit Access Default Value 31:4 R/W 0000000h Description Reserved (MBASEU1): These registers are R/W for compliance purposes only. They should never be programmed to anything other than zeros. 3:0 R/W Fh Prefetchable Memory Base Address (MBASEU): Corresponds to A[35:32] of the lower limit of the prefetchable memory range that will be passed to PCI Express-G. Datasheet 361 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.20 PMLIMITU1 - Prefetchable Memory Limit Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 2C-2Fh 00000000h R/W 32 bits The functionality associated with this register is present in the PEG design implementation. This register in conjunction with the corresponding Upper Limit Address register controls the CPU to PCI Express-G prefetchable memory access routing based on the following formula: PREFETCHABLE_MEMORY_BASE =< address =< PREFETCHABLE_MEMORY_LIMIT The upper 12 bits of this register are read/write and correspond to address bits A[31:20] of the 40- bit address. The lower 8 bits of the Upper Limit Address register are read/write and correspond to address bits A[39:32] of the 40-bit address. This register must be initialized by the configuration software. For the purpose of address decode address bits A[19:0] are assumed to be FFFFFh. Thus, the top of the defined memory address range will be at the top of a 1-MB aligned memory block. Note: Prefetchable memory range is supported to allow segregation by the configuration software between the memory ranges that must be defined as UC and the ones that can be designated as a USWC (i.e., prefetchable) from the CPU perspective. Bit Access Default Value 31:4 R/W 0000000h Description Reserved (MLIMITU1): These registers are R/W for compliance purposes only. They should never be programmed to anything other than zeros. 3:0 R/W 0h Prefetchable Memory Address Limit (MLIMITU): Corresponds to A[35:32] of the upper limit of the prefetchable Memory range that will be passed to PCI Express-G. 362 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.21 CAPPTR1 - Capabilities Pointer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 34h 88h RO 8 bits The capabilities pointer provides the address offset to the location of the first entry in this device's linked list of capabilities. Bit Access Default Value 7:0 RO 88h Description First Capability (CAPPTR1): The first capability in the list is the Subsystem ID and Subsystem Vendor ID Capability. 20.1.22 INTRLINE1 - Interrupt Line B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 3Ch 00h R/W 8 bits This register contains interrupt line routing information. The device itself does not use this value, rather it is used by device drivers and operating systems to determine priority and vector information. Bit Access Default Value 7:0 R/W 00h Description Interrupt Connection (INTCON): Used to communicate interrupt line routing information. BIOS Requirement: POST software writes the routing information into this register as it initializes and configures the system. The value indicates to which input of the system interrupt controller this device's interrupt pin is connected. Datasheet 363 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.23 INTRPIN1 - Interrupt Pin B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 3Dh 01h RO 8 bits This register specifies which interrupt pin this device uses. Bit Access Default Value 7:0 RO 01h Description Interrupt Pin (INTPIN): As a single function device, the PCI Express device specifies INTA as its interrupt pin. 01h=INTA. 20.1.24 BCTRL1 - Bridge Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 3E-3Fh 0000h RO; R/W 16 bits This register provides extensions to the PCICMD1 register that are specific to PCI-PCI bridges. The BCTRL provides additional control for the secondary interface (i.e., PCI Express-G) as well as some bits that affect the overall behavior of the "virtual" HostPCI Express bridge embedded within (G)MCH, e.g., VGA compatible address ranges mapping. Bit Access Default Value Description 15:12 RO 0h Reserved 11 RO 0b Discard Timer SERR Enable (DTSERRE): Not Applicable or Implemented. Hardwired to 0. 10 RO 0b Discard Timer Status (DTSTS): Not Applicable or Implemented. Hardwired to 0. 9 RO 0b Secondary Discard Timer (SDT): Not Applicable or Implemented. Hardwired to 0. 8 RO 0b Primary Discard Timer (PDT): Not Applicable or Implemented. Hardwired to 0. 7 RO 0b Fast Back-to-Back Enable (FB2BEN): Not Applicable or Implemented. Hardwired to 0. 6 R/W 0b Secondary Bus Reset (SRESET): Setting this bit triggers a hot reset on the corresponding PCI Express Port. This will force the LTSSM to transition to the Hot Reset state (via Recovery) from L0, L0s, or L1 states. 364 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Bit Access Default Value 5 RO 0b Description Master Abort Mode (MAMODE): When acting as a master, unclaimed reads that experience a master abort returns all 1's and any writes that experience a master abort completes normally and the data is thrown away. Hardwired to 0. 4 R/W 0b VGA 16-bit Decode (VGA16D): Enables the PCI-to-PCI bridge to provide 16-bit decoding of VGA I/O address precluding the decoding of alias addresses every 1 KB. This bit only has meaning if bit 3 (VGA Enable) of this register is also set to 1, enabling VGA I/O decoding and forwarding by the bridge. 0: Execute 10-bit address decodes on VGA I/O accesses 1: Execute 16-bit address decodes on VGA I/O accesses. 3 R/W 0b VGA Enable (VGAEN): Controls the routing of CPU initiated transactions targeting VGA compatible I/O and memory address ranges. See the VGAEN/MDAP table in Device 0, offset 97h[0]. 2 R/W 0b ISA Enable (ISAEN): Needed to exclude legacy resource decode to route ISA resources to legacy decode path. Modifies the response by the (G)MCH to an I/O access issued by the CPU that target ISA I/O addresses. This applies only to I/O addresses that are enabled by the IOBASE and IOLIMIT registers. 0: All addresses defined by the IOBASE and IOLIMIT for CPU I/O transactions will be mapped to PCI Express-G. 1: (G)MCH will not forward to PCI Express-G any I/O transactions addressing the last 768 bytes in each 1-KB block even if the addresses are within the range defined by the IOBASE and IOLIMIT registers. Instead of going to PCI ExpressG these cycles will be forwarded to DMI where they can be subtractively or positively claimed by the ISA bridge. 1 R/W 0b SERR Enable (SERREN): 0: No forwarding of error messages from secondary side to primary side that could result in an SERR. 1: ERR_COR, ERR_NONFATAL, and ERR_FATAL messages result in SERR message when individually enabled by the Root Control register. 0 R/W 0b Parity Error Response Enable (PEREN): Controls whether or not the Master Data Parity Error bit in the Secondary Status register is set when the (G)MCH receives across the link (upstream) a Read Data Completion Poisoned TLP 0: Master Data Parity Error bit in Secondary Status register cannot be set. 1: Master Data Parity Error bit in Secondary Status register can be set. Datasheet 365 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.25 PM_CAPID1 - Power Management Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 80-83h C8039001h RO 32 bits Bit Access Default Value 31:27 RO 19h Description PME Support (PMES): This field indicates the power states in which this device may indicate PME wake via PCI Express messaging. D0, D3hot and D3cold. This device is not required to do anything to support D3hot and D3cold, it simply must report that those states are supported. Refer to the PCI Power Management 1.1 specification for encoding explanation and other power management details. 26 RO 0b D2 Power State Support (D2PSS): Hardwired to 0 to indicate that the D2 power management state is NOT supported. 25 RO 0b D1 Power State Support (D1PSS): Hardwired to 0 to indicate that the D1 power management state is NOT supported. 24:22 RO 000b Auxiliary Current (AUXC): Hardwired to 0 to indicate that there are no 3.3Vaux auxiliary current requirements. 21 RO 0b Device Specific Initialization (DSI): Hardwired to 0 to indicate that special initialization of this device is not required before generic class device driver is to use it. 20 RO 0b Auxiliary Power Source (APS): Hardwired to 0. 19 RO 0b PME Clock (PMECLK): Hardwired to 0 to indicate this device does NOT support PMEB generation. 18:16 RO 011b PCI PM CAP Version (PCIPMCV): Version: - A value of 011b indicates that this function complies with revision 1.2 of the PCI Power Management Interface Specification. 15:8 RO 90h Pointer to Next Capability (PNC): This contains a pointer to the next item in the capabilities list. If MSICH (CAPL[0] @ 7Fh) is 0, then the next item in the capabilities list is the Message Signaled Interrupts (MSI) capability at 90h. If MSICH (CAPL[0] @ 7Fh) is 1, then the next item in the capabilities list is the PCI Express capability at A0h. 7:0 RO 01h Capability ID (CID): Value of 01h identifies this linked list item (capability structure) as being for PCI Power Management registers. 366 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.26 PM_CS1 - Power Management Control/Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 84-87h 00000000h RO; R/W/S; R/W 32 bits Bit Access Default Value 31:16 RO 0000h Description Reserved Not Applicable or Implemented. Hardwired to 0. 15 RO 0b PME Status (PMESTS): Indicates that this device does not support PMEB generation from D3cold. 14:13 RO 00b Data Scale (DSCALE): Indicates that this device does not support the power management data register. 12:9 RO 0h Data Select (DSEL): Indicates that this device does not support the power management data register. 8 R/W/S 0b PME Enable (PMEE): Indicates that this device does not generate PMEB assertion from any D-state. 0: PMEB generation not possible from any D State 1: PMEB generation enabled from any D State The setting of this bit has no effect on hardware. See PM_CAP[15:11] 7:2 Datasheet RO 00h Reserved 367 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Bit Access Default Value 1:0 R/W 00b Description Power State (PS): Indicates the current power state of this device and can be used to set the device into a new power state. If software attempts to write an unsupported state to this field, write operation must complete normally on the bus, but the data is discarded and no state change occurs. 00: D0 01: D1 (Not supported in this device.) 10: D2 (Not supported in this device.) 11: D3 Support of D3cold does not require any special action. While in the D3hot state, this device can only act as the target of PCI configuration transactions (for power management control). This device also cannot generate interrupts or respond to MMR cycles in the D3 state. The device must return to the D0 state in order to be fully-functional. When the Power State is other than D0, the bridge will Master Abort (i.e., not claim) any downstream cycles (with exception of type 0 config cycles). Consequently, these unclaimed cycles will go down DMI and come back up as Unsupported Requests, which the (G)MCH logs as Master Aborts in Device 0 PCISTS[13] There is no additional hardware functionality required to support these Power States. 368 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.27 SS_CAPID - Subsystem ID and Vendor ID Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 88-8Bh 0000800Dh RO 32 bits This capability is used to uniquely identify the subsystem where the PCI device resides. Because this device is an integrated part of the system and not an add-in device, it is anticipated that this capability will never be used. However, it is necessary because Microsoft will test for its presence. Bit Access Default Value 31:16 RO 0000h 15:8 RO 80h Description Reserved Pointer to Next Capability (PNC): This contains a pointer to the next item in the capabilities list which is the PCI Power Management capability. 7:0 RO 0Dh Capability ID (CID): Value of 0Dh identifies this linked list item (capability structure) as being for SSID/SSVID registers in a PCI-to-PCI Bridge. 20.1.28 SS - Subsystem ID and Subsystem Vendor ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 8C-8Fh 00008086h R/WO 32 bits System BIOS can be used as the mechanism for loading the SSID/SVID values. These values must be preserved through power management transitions and a hardware reset. Bit Access Default Value 31:16 R/WO 0000h Description Subsystem ID (SSID): Identifies the particular subsystem and is assigned by the vendor. 15:0 R/WO 8086h Subsystem Vendor ID (SSVID): Identifies the manufacturer of the subsystem and is the same as the vendor ID which is assigned by the PCI Special Interest Group. Datasheet 369 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.29 MSI_CAPID - Message Signaled Interrupts Capability ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 90-91h A005h RO 16 bits When a device supports MSI it can generate an interrupt request to the processor by writing a predefined data item (a message) to a predefined memory address. The reporting of the existence of this capability can be disabled by setting MSICH (CAPL[0] @ 7Fh). In that case walking this linked list will skip this capability and instead go directly from the PCI PM capability to the PCI Express capability. Bit Access Default Value 15:8 RO A0h Description Pointer to Next Capability (PNC): This contains a pointer to the next item in the capabilities list which is the PCI Express capability. 7:0 RO 05h Capability ID (CID): Value of 05h identifies this linked list item (capability structure) as being for MSI registers. 370 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.30 MC - Message Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 92-93h 0000h RO; R/W 16 bits System software can modify bits in this register, but the device is prohibited from doing so. If the device writes the same message multiple times, only one of those messages is guaranteed to be serviced. If all of them must be serviced, the device must not generate the same message again until the driver services the earlier one. Bit Access Default Value 15:8 RO 00h 7 RO 0b Description Reserved 64-Bit Address Capable (64AC): Hardwired to 0 to indicate that the function does not implement the upper 32 bits of the Message Address register and is incapable of generating a 64-bit memory address. This may need to change in future implementations when addressable system memory exceeds the 32-bit/4-GB limit. 6:4 R/W 000b Multiple Message Enable (MME): System software programs this field to indicate the actual number of messages allocated to this device. This number will be equal to or less than the number actually requested. The encoding is the same as for the MMC field below. 3:1 RO 000b Multiple Message Capable (MMC): System software reads this field to determine the number of messages being requested by this device. Value: Number of Messages Requested 000: 1 All of the following are reserved in this implementation: 0 R/W 0b 001: 2 010: 4 011: 8 100: 16 101: 32 110: Reserved 111: Reserved MSI Enable (MSIEN): Controls the ability of this device to generate MSIs. 0: MSI will not be generated. 1: MSI will be generated when we receive PME or HotPlug messages. INTA will not be generated and INTA Status (PCISTS1[3]) will not be set. Datasheet 371 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.31 MA - Message Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 94-97h 00000000h R/W; RO 32 bits Bit Access Default Value 31:2 R/W 00000000 h 1:0 RO 00b Description Message Address (MA): Used by system software to assign an MSI address to the device. The device handles an MSI by writing the padded contents of the MD register to this address. Force Dword Align (FDWA): Hardwired to 0 so that addresses assigned by system software are always aligned on a Dword address boundary. 20.1.32 MD - Message Data B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI 98-99h 0000h R/W 16 bits Bit Access Default Value 15:0 R/W 0000h Description Message Data (MD): Base message data pattern assigned by system software and used to handle an MSI from the device. When the device must generate an interrupt request, it writes a 32-bit value to the memory address specified in the MA register. The upper 16 bits are always set to 0. The lower 16 bits are supplied by this register. 372 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.33 PEG_CAPL - PCI Express-G Capability List B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI A0-A1h 0010h RO 16 bits This register enumerates the PCI Express capability structure. Bit Access Default Value 15:8 RO 00h Description Pointer to Next Capability (PNC): This value terminates the capabilities list. The Virtual Channel capability and any other PCI Express specific capabilities that are reported via this mechanism are in a separate capabilities list located entirely within PCI Express Extended Configuration Space. 7:0 RO 10h Capability ID (CID): Identifies this linked list item (capability structure) as being for PCI Express registers. Datasheet 373 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.34 PEG_CAP - PCI Express-G Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI A2-A3h 0141h RO; R/WO 16 bits This register indicates PCI Express device capabilities. Bit Access Default Value Description 15:14 RO 00b Reserved 13:9 RO 00h Interrupt Message Number (IMN): Not Applicable or Implemented. Hardwired to 0. 8 R/WO 1b Slot Implemented (SI): 0: The PCI Express Link associated with this port is connected to an integrated component or is disabled. 1: The PCI Express Link associated with this port is connected to a slot. BIOS Requirement: This field must be initialized appropriately if a slot connection is not implemented. 7:4 RO 4h Device/Port Type (DPT): Hardwired to 4h to indicate root port of PCI Express Root Complex. 3:0 RO 1h PCI Express Capability Version (PCIECV): Hardwired to 1 as it is the first version. 374 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.35 DCAP - Device Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI A4-A7h 00008000h RO 32 bits This register indicates PCI Express device capabilities. Bit Access Default Value 31: 6 RO 0000h 5 RO 0b Description Reserved Extended Tag Field Supported (ETFS): Hardwired to indicate support for 5-bit Tags as a Requestor. 4:3 RO 00b Phantom Functions Supported (PFS): Not Applicable or Implemented. Hardwired to 0. 2:0 RO 000b Max Payload Size (MPS): Hardwired to indicate 128-B max supported payload for Transaction Layer Packets (TLP). Datasheet 375 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.36 DCTL - Device Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI A8-A9h 0000h RO; R/W; 16 bits Provides control for PCI Express device specific capabilities. The error reporting enable bits are in reference to errors detected by this device, not error messages received across the link. The reporting of error messages (ERR_CORR, ERR_NONFATAL, ERR_FATAL) received by Root Port is controlled exclusively by Root Port Command Register. Bit Access Default Value Description 15:12 RO 0h Reserved 11 RO 0b Reserved 10:8 RO 000b Reserved 7:5 R/W 000b Max Payload Size (MPS): 000: 128-B max supported payload for Transaction Layer Packets (TLP). As a receiver, the Device must handle TLPs as large as the set value; as transmitter, the Device must not generate TLPs exceeding the set value. All other encodings are reserved. Hardware will actually ignore this field. It is writeable only to support compliance testing. 4 RO 0b Reserved 3 R/W 0b Unsupported Request Reporting Enable (URRE): When set, Unsupported Requests will be reported. Note that reporting of error messages received by Root Port is controlled exclusively by Root Control register. 2 R/W 0b Fatal Error Reporting Enable (FERE): When set fatal errors will be reported. For a Root Port, the reporting of fatal errors is internal to the root. No external ERR_FATAL message is generated. 1 R/W 0b Non-Fatal Error Reporting Enable (NFERE): When set non-fatal errors will be reported. For a Root Port, the reporting of non-fatal errors is internal to the root. No external ERR_NONFATAL message is generated. Uncorrectable errors can result in degraded performance. 0 R/W 0b Correctable Error Reporting Enable (CERE): When set correctable errors will be reported. For a Root Port, the reporting of correctable errors is internal to the root. No external ERR_CORR message is generated. 376 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.37 DSTS - Device Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI AA-ABh 0000h RO; R/WC 16 bits This register reflects status corresponding to controls in the Device Control register. The error reporting bits are in reference to errors detected by this device, not errors messages received across the link. Bit Access Default Value 15:6 RO 000h 5 RO 0b Description Reserved Transactions Pending (TP): 0: All pending transactions (including completions for any outstanding non-posted requests on any used virtual channel) have been completed. 1: Indicates that the device has transaction(s) pending (including completions for any outstanding non-posted requests for all used Traffic Classes). 4 RO 0b Reserved 3 R/WC 0b Unsupported Request Detected (URD): When set this bit indicates that the Device received an Unsupported Request. Errors are logged in this register regardless of whether error reporting is enabled or not in the Device Control Register. Additionally, the Non-Fatal Error Detected bit or the Fatal Error Detected bit is set according to the setting of the Unsupported Request Error Severity bit. In production systems setting the Fatal Error Detected bit is not an option as support for AER will not be reported. 2 R/WC 0b Fatal Error Detected (FED): When set this bit indicates that fatal error(s) were detected. Errors are logged in this register regardless of whether error reporting is enabled or not in the Device Control register. When Advanced Error Handling is enabled, errors are logged in this register regardless of the settings of the uncorrectable error mask register. 1 R/WC 0b Non-Fatal Error Detected (NFED): When set this bit indicates that non-fatal error(s) were detected. Errors are logged in this register regardless of whether error reporting is enabled or not in the Device Control register. When Advanced Error Handling is enabled, errors are logged in this register regardless of the settings of the uncorrectable error mask register. Datasheet 377 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Bit Access Default Value 0 R/WC 0b Description Correctable Error Detected (CED): When set this bit indicates that correctable error(s) were detected. Errors are logged in this register regardless of whether error reporting is enabled or not in the Device Control register. When Advanced Error Handling is enabled, errors are logged in this register regardless of the settings of the correctable error mask register. 20.1.38 LCAP - Link Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI AC-AFh 02014D01h RO; R/WO 32 bits This register indicates PCI Express device specific capabilities. Bit Access Default Value 31:24 RO 02h Description Port Number (PN): Indicates the PCI Express port number for the given PCI Express link. Matches the value in Element Self Description [31:24]. 23:18 RO 000b Reserved 17:15 R/WO 010b L1 Exit Latency (L1ELAT): Indicates the length of time this Port requires to complete the transition from L1 to L0. The value 010 b indicates the range of 2 s to less than 4 s BIOS Requirement: If this field is required to be any value other than the default, BIOS must initialize it accordingly. Both bytes of this register that contain a portion of this field must be written simultaneously in order to prevent an intermediate (and undesired) value from ever existing. 14:12 RO 100b L0s Exit Latency (L0SELAT): Indicates the length of time this Port requires to complete the transition from L0s to L0. 000: Less than 64 ns 001: 64 ns to less than 128 ns 010: 128 ns to less than 256 ns 011: 256 ns to less than 512 ns 100: 512 ns to less than 1 s 101: 1 s to less than 2 s 110: 2 s - 4 s 111: More than 4 s The actual value of this field depends on the common Clock Configuration bit (LCTL[6]). 378 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Bit Access Default Value Description 11:10 R/WO 11b Active State Link PM Support (ASLPMS) 9:4 RO 10h Max Link Width (MLW): Indicates the maximum number of lanes supported for this link. 3:0 Datasheet RO 1h Max Link Speed (MLS): Hardwired to indicate 2.5 Gb/s. 379 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.39 LCTL - Link Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI B0-B1h 0040h RO; R/W; 16 bits This register allows control of PCI Express Link. Bit Access Default Value 15:9 RO 0000000b 8 RO 0b Description Reserved Enable Clock Power Management (ECPM): Applicable only for form factors that support a "Clock Request" (CLKREQ#) mechanism, this enable functions as follows 0b: Clock power management is disabled and device must hold CLKREQ# signal low (Default). 1b: When this bit is set to 1 the device is permitted to use CLKREQ# signal to power manage link clock according to protocol defined in appropriate form factor specification. Components that do not support Clock Power Management (as indicated by a 0b value in the Clock Power Management bit of the Link Capabilities Register) must hardwire this bit to 0b. 7 R/W 0b Extended Synch (ES): 0: Standard Fast Training Sequence (FTS). 1: Forces the transmission of additional ordered sets when exiting the L0s state and when in the Recovery state. This mode provides external devices (e.g., logic analyzers) monitoring the Link time to achieve bit and symbol lock before the link enters L0 and resumes communication. This is a test mode only and may cause other undesired side effects such as buffer overflows or underruns. 6 R/W 1b Common Clock Configuration (CCC): 0: Indicates that this component and the component at the opposite end of this Link are operating with asynchronous reference clock. 1: Indicates that this component and the component at the opposite end of this Link are operating with a distributed common reference clock. The state of this bit affects the L0s Exit Latency reported in LCAP[14:12] and the N_FTS value advertised during link training. 5 R/W 0b Retrain Link (RL): 0: Normal operation. 1: Full Link retraining is initiated by directing the Physical Layer LTSSM from L0, L0s, or L1 states to the Recovery state. This bit always returns 0 when read. This bit is cleared automatically (no need to write a 0). 380 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Bit Access Default Value 4 R/W 0b Description Link Disable (LD): 0: Normal operation 1: Link is disabled. Forces the LTSSM to transition to the Disabled state (via Recovery) from L0, L0s, or L1 states. Link retraining happens automatically on 0 to 1 transition, just like when coming out of reset. Writes to this bit are immediately reflected in the value read from the bit, regardless of actual Link state. 3 RO 0b Read Completion Boundary (RCB): Hardwired to 0 to indicate 64 byte. 2 R/W 0b 1:0 R/W 00b Far-End Digital Loopback (FEDLB): Active State PM (ASPM): Controls the level of active state power management supported on the given link. Datasheet 00: Disabled 01: L0s Entry Supported 10: Reserved 11: L0s and L1 Entry Supported 381 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.40 LSTS - Link Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI B2-B3h 1001h RO 16 bits Indicates PCI Express Link status. Bit Access Default Value 15:13 RO 00b 12 RO 1b Description Reserved Slot Clock Configuration (SCC): 0: The device uses an independent clock irrespective of the presence of a reference on the connector. 1: The device uses the same physical reference clock that the platform provides on the connector. 11 RO 0b Link Training (LTRN): Indicates that the Physical Layer LTSSM is in the Configuration or Recovery state, or that 1b was written to the Retrain Link bit but Link training has not yet begun. Hardware clears this bit when the LTSSM exits the Configuration/Recovery state once Link training is complete. 10 RO 0b 9:4 RO 00h Reserved Negotiated Width (NW): Indicates negotiated link width. This field is valid only when the link is in the L0, L0s, or L1 states (after link width negotiation is successfully completed) 00h: Reserved 01h: X1 02h: X2 04h: X4 08h: X8 10h: X16 All other encodings are reserved. 3:0 RO 1h Negotiated Speed (NS): Indicates negotiated link speed. 1h: 2.5 Gb/s All other encodings are reserved. 382 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.41 SLOTCAP - Slot Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI B4-B7h 00040000h R/WO; RO 32 bits PCI Express Slot related registers allow for the support of Hot Plug. Bit Access Default Value 31:19 R/WO 0000h Description Physical Slot Number (PSN): Indicates the physical slot number attached to this Port. BIOS Requirement: This field must be initialized by BIOS to a value that assigns a slots number that is globally unique within the chassis. 18 R/WO 1b No Command Completed Support (NCCS): When set to 1b, this bit indicates that this slot does not generate software notification when an issued command is completed by the Hot-Plug Controller. This bit is only permitted to be set to 1b if the hotplug capable port is able to accept writes to all fields of the Slot Control register without delay between successive writes. 17 RO 0b 16:15 R/WO 00b Reserved Slot Power Limit Scale (SPLS): Specifies the scale used for the Slot Power Limit Value. 00: 1.0x 01: 0.1x 10: 0.01x 11: 0.001x If this field is written, the link sends a Set_Slot_Power_Limit message. 14:7 R/WO 00h Slot Power Limit Value (SPLV): In combination with the Slot Power Limit Scale value, specifies the upper limit on power supplied by slot. Power limit (in Watts) is calculated by multiplying the value in this field by the value in the Slot Power Limit Scale field. If this field is written, the link sends a Set_Slot_Power_Limit message. 6 RO 0b Reserved for Hot-plug Capable (HPC): Indicates that this slot is capable of supporting hot-lug operations. 5 RO 0b Reserved for Hot-plug Surprise (HPS): Indicates that a device in this slot might be removed from the system without any prior notification. Datasheet 383 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Bit Access Default Value 4 RO 0b Description Power Indicator Present (PIP): Indicates that a Power Indicator is electrically controlled by the chassis for this slot. 3 RO 0b Attention Indicator Present (AIP): Indicates that an Attention Indicator is implemented on the chassis for this slot 2 RO 0b Reserved 1 RO 0b Reserved 0 RO 0b Reserved for Attention Button Present (ABP): Indicates that an Attention Indicator is implemented on the chassis for this slot 384 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.42 SLOTCTL - Slot Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI B8-B9h 01C0h RO; R/W 16 bits PCI Express Slot related registers allow for the support of Hot Plug. Bit Access Default Value 15:10 RO 000b 9:8 RO 01b Description Reserved Power Indicator Control (PIC): Reads to this field reflects the state of current power indicator. Writes to this field set the Power indicator and cause the port to send the appropriate Power_Indicator _* messages 00: Reserved 01: On 10: Blink 11: Off 7:6 RO 11b Reserved for Attention Indicator Control (AIC): Reads to this field reflects the state of current power indicator. Writes to this field set the Power indicator and cause the port to send the appropriate Power_Indicator _* messages 00: Reserved 01: On 10: Blink 11: Off 5 RO 0b Reserved for Hot-plug Interrupt Enable (HPIE): When set , this bit enables generation of an interrupt on enabled hot-plug events 4 RO 0b Command Completed Interrupt Enable (CCI): When set enables software notification when a hot-plug command is completed by the Hot-Plug Controller. 3 R/W 0b Presence Detect Changed Enable (PDCE): When set to 1b, this bit enables software notification on a presence detect changed event. 2 RO 0b Reserved 1 RO 0b Reserved 0 RO 0b Attention Button Pressed Enable (ABPE): When set enables software notification on an attention button pressed event. Datasheet 385 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.43 SLOTSTS - Slot Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI BA-BBh 0000h RO; R/WC 16 bits PCI Express Slot related registers allow for the support of Hot Plug. Bit Access Default Value 15:7 RO 000h 6 RO 0b Description Reserved Presence Detect State (PDS): Indicates the presence of an adapter in the slot, 0b Slot Empty 1b Card Present in slot 5 RO 0b Reserved 4 RO 0b Reserved 3 R/WC 0b Presence Detect Changed (PDC): This bit is set when the value reported in Presence Detect State is changed. 2 RO 0b Reserved 1 RO 0b Reserved for Power Fault Detected (PFD): If a Power Controller that supports power fault detection is implemented, this bit is set when the Power Controller detects a power fault at this slot. Note that, depending on hardware capability, it is possible that a power fault can be detected at any time, independent of the Power Controller Control setting or the occupancy of the slot. If power fault detection is not supported, this bit must not be set. 0 386 RO 0b Reserved Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.44 RCTL - Root Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI BC-BDh 0000h RO; R/W 16 bits This register allows control of PCI Express Root Complex specific parameters. The system error control bits in this register determine if corresponding SERRs are generated when our device detects an error (reported in this device's Device Status register) or when an error message is received across the link. Reporting of SERR as controlled by these bits takes precedence over the SERR Enable in the PCI Command Register. Bit Access Default Value 15:4 RO 000h 3 R/W 0b Description Reserved PME Interrupt Enable (PMEIE): 0: No interrupts are generated as a result of receiving PME messages. 1: Enables interrupt generation upon receipt of a PME message as reflected in the PME Status bit of the Root Status Register. A PME interrupt is also generated if the PME Status bit of the Root Status Register is set when this bit is set from a cleared state. 2 R/W 0b System Error on Fatal Error Enable (SEFEE): Controls the Root Complex's response to fatal errors. 0: No SERR generated on receipt of fatal error. 1: Indicates that an SERR should be generated if a fatal error is reported by any of the devices in the hierarchy associated with this Root Port, or by the Root Port itself. 1 R/W 0b System Error on Non-Fatal Uncorrectable Error Enable (SENFUEE): Controls the Root Complex's response to non-fatal errors. 0: No SERR generated on receipt of non-fatal error. 1: Indicates that an SERR should be generated if a non-fatal error is reported by any of the devices in the hierarchy associated with this Root Port, or by the Root Port itself. 0 R/W 0b System Error on Correctable Error Enable (SECEE): Controls the Root Complex's response to correctable errors. 0: No SERR generated on receipt of correctable error. 1: Indicates that an SERR should be generated if a correctable error is reported by any of the devices in the hierarchy associated with this Root Port, or by the Root Port itself. Datasheet 387 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.45 RSTS - Root Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI C0-C3h 00000000h RO; R/WC 32 bits This register provides information about PCI Express Root Complex specific parameters. Bit Access Default Value 31:18 RO 0000h 17 RO 0b Description Reserved PME Pending (PMEP): Indicates that another PME is pending when the PME Status bit is set. When the PME Status bit is cleared by software; the PME is delivered by hardware by setting the PME Status bit again and updating the Requestor ID appropriately. The PME pending bit is cleared by hardware if no more PMEs are pending. 16 R/WC 0b PME Status (PMES): Indicates that PME was asserted by the requestor ID indicated in the PME Requestor ID field. Subsequent PMEs are kept pending until the status register is cleared by writing a 1 to this field. 15:0 RO 0000h PME Requestor ID (PMERID): Indicates the PCI requestor ID of the last PME requestor. 388 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.1.46 PEGLC - PCI Express-G Legacy Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/PCI EC-EFh 00000000h RO; R/W 32 bits Controls functionality that is needed by legacy (non-PCI Express aware) OS's during run time. Bit Access Default Value 31:3 RO 00000000h 2 R/W 0b Description Reserved PME GPE Enable (PMEGPE): 0: Do not generate GPE PME message when PME is received. 1: Generate a GPE PME message when PME is received (Assert_PMEGPE and Deassert_PMEGPE messages on DMI). This enables the (G)MCH to support PMEs on the PEG port under legacy operating systems. 1 R/W 0b Hot-Plug GPE Enable (HPGPE): 0: Do not generate GPE Hot-Plug message when Hot-Plug event is received. 1: Generate a GPE Hot-Plug message when Hot-Plug Event is received (Assert_HPGPE and Deassert_HPGPE messages on DMI). This enables the (G)MCH to support Hot-Plug on the PEG port under legacy operating systems. 0 R/W 0b General Message GPE Enable (GENGPE): 0: Do not forward received GPE assert/deassert messages 1: Forward received GPE assert/deassert messages. These general GPE message can be received via the PEG port from an external Intel device (i.e., PxH) and will be subsequently forwarded to the ICH (via Assert_GPE and Deassert_GPE messages on DMI). For example, PxH might send this message if a PCI Express device is hot plugged into a PxH downstream port. Datasheet 389 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.2 PEG Device 1 Function 0 Extended Configuration Registers Extended capability structures for PCI Express devices are located in PCI Express extended configuration space and have different field definition than standard PCI capability structures. Register Name Register Symbol Register End Default Value Access Virtual Channel Enhanced Capability Header VCECH 100 103 14010002h RO Port VC Capability Register 1 PVCCAP1 104 107 00000000h RO Port VC Capability Register 2 PVCCAP2 108 10B 00000001h RO Port VC Control PVCCTL 10C 10D 0000h RO; R/W 10E 10F Reserved VC0 Resource Capability VC0RCAP 110 113 00000000h RO VC0 Resource Control VC0RCTL 114 117 800000FFh RO; R/W 118 119 Reserved VC0 Resource Status VC0RSTS 11A 11B 0002h RO VC1 Resource Capability VC1RCAP 11C 11F 00000000h RO VC1 Resource Control VC1RCTL 120 123 00000000h RO 124 125 126 127 0000h RO 128 13F Reserved VC1 Resource Status VC1RSTS Reserved Root Complex Link Declaration Enhanced RCLDECH 140 143 00010005h RO Element Self Description ESD 144 147 02000100h RO; R/WO 148 14F 150 153 00000000h RO; R/WO 154 157 Reserved Link Entry 1 Description Reserved 390 Register Start LE1D Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) Register Name Link Entry 1 Address 20.2.1 Register Symbol LE1A Register Start 158 Register End 15F Default Value 0000000000 000000h Access RO; R/WO VCECH - Virtual Channel Enhanced Capability Header B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 100-103h 14010002h RO 32 bits This register indicates PCI Express device Virtual Channel capabilities. Extended capability structures for PCI Express devices are located in PCI Express extended configuration space and have different field definitions than standard PCI capability structures. Bit Access Default Value 31:20 RO 140h Description Pointer to Next Capability (PNC): The Link Declaration Capability is the next in the PCI Express extended capabilities list. 19:16 RO 1h PCI Express Virtual Channel Capability Version (PCIEVCCV): Hardwired to 1 to indicate compliances with the 1.0 version of the PCI Express specification. 15:0 RO 0002h Extended Capability ID (ECID): Value of 0002h identifies this linked list item (capability structure) as being for PCI Express Virtual Channel registers. Datasheet 391 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.2.2 PVCCAP1 - Port VC Capability Register 1 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 104-107h 00000000h RO 32 bits Describes the configuration of PCI Express Virtual Channels associated with this port. Bit Access Default Value 31:7 RO 0000000h 6:4 RO 000b Description Reserved Low Priority Extended VC Count (LPEVCC): Indicates the number of (extended) Virtual Channels in addition to the default VC belonging to the low-priority VC (LPVC) group that has the lowest priority with respect to other VC resources in a strict-priority VC Arbitration. The value of 0 in this field implies strict VC arbitration. 3 RO 0b 2:0 RO 000b Reserved Extended VC Count (EVCC): Indicates the number of (extended) Virtual Channels in addition to the default VC supported by the device. 20.2.3 PVCCAP2 - Port VC Capability Register 2 B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 108-10Bh 00000001h RO 32 bits Describes the configuration of PCI Express Virtual Channels associated with this port. Bit Access Default Value 31:24 RO 00h Description VC Arbitration Table Offset (VCATO): Indicates the location of the VC Arbitration Table. This field contains the zero-based offset of the table in DQWORDS (16 bytes) from the base address of the Virtual Channel Capability Structure. A value of 0 indicates that the table is not present (due to fixed VC priority). 23:8 RO 0000h 7:0 RO 01h Reserved VC Arbitration Capability (VCAC): Indicates that the only possible VC arbitration scheme is hardware fixed (in the root complex). VC1 is the highest priority. VC0 is the lowest priority. 392 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.2.4 PVCCTL - Port VC Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 10C-10Dh 0000h RO; R/W 16 bits Bit Access Default Value Description 15:4 RO 000h Reserved 3:1 R/W 000b VC Arbitration Select (VCAS): This field will be programmed by software to the only possible value as indicated in the VC Arbitration Capability field. The value 001b when written to this field will indicate the VC arbitration scheme is hardware fixed (in the root complex). This field can not be modified when more than one VC in the LPVC group is enabled. 0 20.2.5 RO 0b Reserved VC0RCAP - VC0 Resource Capability B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 110-113h 00000000h RO 32 bits Bit Access Default Value 31:16 RO 00h 15 RO 0b Description Reserved Reject Snoop Transactions (RSNPT): 0: Transactions with or without the No Snoop bit set within the TLP header are allowed on this VC. 1: Any transaction without the No Snoop bit set within the TLP header will be rejected as an Unsupported Request. 14:0 Datasheet RO 0000h Reserved 393 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.2.6 VC0RCTL - VC0 Resource Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 114-117h 800000FFh RO; R/W 32 bits Controls the resources associated with PCI Express Virtual Channel 0. Bit Access Default Value 31 RO 1b Description VC0 Enable (VC0E): For VC0 this is hardwired to 1 and read only as VC0 can never be disabled. 30:27 RO 0h 26:24 RO 000b Reserved VC0 ID (VC0ID): Assigns a VC ID to the VC resource. For VC0 this is hardwired to 0 and read only. 23:8 RO 0000h 7:1 R/W 7Fh Reserved TC/VC0 Map (TCVC0M): Indicates the TCs (Traffic Classes) that are mapped to the VC resource. Bit locations within this field correspond to TC values. For example, when bit 7 is set in this field, TC7 is mapped to this VC resource. When more than one bit in this field is set, it indicates that multiple TCs are mapped to the VC resource. In order to remove one or more TCs from the TC/VC Map of an enabled VC, software must ensure that no new or outstanding transactions with the TC labels are targeted at the given Link. 0 RO 1b TC0/VC0 Map (TC0VC0M): Traffic Class 0 is always routed to VC0. 394 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.2.7 VC0RSTS - VC0 Resource Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 11A-11Bh 0002h RO 16 bits This register reports the Virtual Channel specific status. Bit Access Default Value 15:2 RO 0000h 1 RO 1b Description Reserved VC0 Negotiation Pending (VC0NP): 0: The VC negotiation is complete. 1: The VC resource is still in the process of negotiation (initialization or disabling). This bit indicates the status of the process of Flow Control initialization. It is set by default on Reset, as well as whenever the corresponding Virtual Channel is Disabled or the Link is in the DL_Down state. It is cleared when the link successfully exits the FC_INIT2 state. Before using a Virtual Channel, software must check whether the VC Negotiation Pending fields for that Virtual Channel are cleared in both Components on a Link. 0 20.2.8 RO 0b VC1RCAP - VC1 Resource Capability B/D/F/Type: Address Offset: Default Value: Access: Size: Datasheet Reserved 0/1/0/MM 11C-11Fh 00000000h RO 32 bits Bit Access Default Value 31:0 RO 00000000h Description Reserved 395 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.2.9 VC1RCTL - VC1 Resource Control B/D/F/Type: Address Offset: Default Value: Access: Size: 20.2.10 0/1/0/MM 120-123h 00000000h RO 32 bits Bit Access Default Value 31:0 RO 00000000h Reserved VC1RSTS - VC1 Resource Status B/D/F/Type: Address Offset: Default Value: Access: Size: 396 Description 0/1/0/MM 126-127h 0000h RO 16 bits Bit Access Default Value 15:0 RO 0000h Description Reserved Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.2.11 RCLDECH - Root Complex Link Declaration Enhanced B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 140-143h 00010005h RO 32 bits This capability declares links from this element (PEG) to other elements of the root complex component to which it belongs. See PCI Express specification for link/topology declaration requirements. Bit Access Default Value 31:20 RO 000h Description Pointer to Next Capability (PNC): This is the last capability in the PCI Express extended capabilities list 19:16 RO 1h Link Declaration Capability Version (LDCV): Hardwired to 1 to indicate compliances with the 1.0 version of the PCI Express specification. 15:0 RO 0005h Extended Capability ID (ECID): Value of 0005 h identifies this linked list item (capability structure) as being for PCI Express Link Declaration Capability. See corresponding Egress Port Link Declaration Capability registers for diagram of Link Declaration Topology. Datasheet 397 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.2.12 ESD - Element Self Description B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 144-147h 02000100h RO; R/WO 32 bits This register provides information about the root complex element containing this Link Declaration Capability. Bit Access Default Value 31:24 RO 02h Description Port Number (PN): Specifies the port number associated with this element with respect to the component that contains this element. This port number value is utilized by the egress port of the component to provide arbitration to this Root Complex Element. 23:16 R/WO 00h Component ID (CID): Identifies the physical component that contains this Root Complex Element. BIOS Requirement: Must be initialized according to guidelines in the PCI Express* Isochronous/Virtual Channel Support Hardware Programming Specification (HPS). 15:8 RO 01h Number of Link Entries (NLE): Indicates the number of link entries following the Element Self Description. This field reports 1 (to Egress port only as we don't report any peer-to-peer capabilities in our topology). 7:4 RO 0h Reserved 3:0 RO 0h Element Type (ET): Indicates the type of the Root Complex Element. Value of 0 h represents a root port. 398 Datasheet PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.2.13 LE1D - Link Entry 1 Description B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 150-153h 00000000h RO; R/WO 32 bits This register is the first part of a Link Entry which declares an internal link to another Root Complex Element. Bit Access Default Value 31:24 RO 00h Description Target Port Number (TPN): Specifies the port number associated with the element targeted by this link entry (Egress Port). The target port number is with respect to the component that contains this element as specified by the target component ID. 23:16 R/WO 00h Target Component ID (TCID): Identifies the physical or logical component that is targeted by this link entry. BIOS Requirement: Must be initialized according to guidelines in the PCI Express* Isochronous/Virtual Channel Support Hardware Programming Specification (HPS). 15:2 RO 0000h 1 RO 0b Reserved Link Type (LTYP): Indicates that the link points to memory-mapped space (for RCRB). The link address specifies the 64-bit base address of the target RCRB. 0 R/WO 0b Link Valid (LV): 0: Link Entry is not valid and will be ignored. 1: Link Entry specifies a valid link. Datasheet 399 PCI Express* Graphics Device 1 Configuration Registers (D1:F0) 20.2.14 LE1A - Link Entry 1 Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/1/0/MM 158-15Fh 0000000000000000h RO; R/WO 64 bits This register is the second part of a Link Entry which declares an internal link to another Root Complex Element. Bit Access Default Value 63:32 RO 00000000h 31:12 R/WO 00000h Description Reserved Link Address (LA): Memory mapped base address of the RCRB that is the target element (Egress Port) for this link entry. 11:0 RO 000h Reserved 400 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21 Internal Graphics Device 2 Configuration Register (D2:F0F1) Device 2 contains registers for the internal graphics functions. The table below lists the PCI configuration registers in order of ascending offset address. Function 0 can be VGA compatible or not, this selected through bit 1 of GGC register (Device 0, offset 52h). The following sections describe Device 2 PCI configuration registers only. 21.1 Internal Graphics Device 2 Configuration Register Details (D2:F0) Register Name Register Symbol Register Start Register End Default Value Access Vendor Identification VID2 0 1 8086h Device Identification DID2 2 3 2A02h1 PCI Command PCICMD2 4 5 0000h RO; R/W PCI Status PCISTS2 6 7 0090h RO Revision Identification RID2 8 8 00h RO Class Code CC 9 B 030000h RO Cache Line Size CLS C C 00h RO Master Latency Timer MLT2 D D 00h RO Header Type HDR2 E E 80h RO F F 10 17 00000000000 00004h RO; R/W Datasheet RO 2 2A12h Reserved Graphics Translation Table Range Address RO GTTMMADR 401 Internal Graphics Device 2 Configuration Register (D2:F0-F1) Register Name Register Symbol Register End Default Value Access Graphics Memory Range Address GMADR 18 1F 00000000000 0000Ch R/W; RO; R/W/L I/O Base Address IOBAR 20 23 00000001h RO; R/W 24 2B Reserved Subsystem Vendor Identification SVID2 2C 2D 0000h R/WO Subsystem Identification SID2 2E 2F 0000h R/WO Video BIOS ROM Base Address ROMADR 30 33 00000000h RO Capabilities Pointer CAPPOINT 34 34 90h RO 25 3B Reserved Interrupt Line INTRLINE 3C 3C 00h R/W Interrupt Pin INTRPIN 3D 3D 01h RO Minimum Grant MINGNT 3E 3E 00h RO Maximum Latency MAXLAT 3F 3F 00h RO 40 43 44 44 48h RO 45 51 Reserved Capabilities Pointer ( to Mirror of Dev0 CAPID ) MCAPPTR Reserved Mirror of Dev0 (G)MCH Graphics Control MGGC 52 53 0030h RO Mirror of Dev0 DEVEN MDEVENdev0 F0 54 57 0000001Bh RO 58 5B 5C 63 00000000000 00000h RO 64 65 66 66 02h RO; R/W; R/W/L Reserved Base of Stolen Memory BSM Reserved Multi Size Aperture Control 402 Register Start MSAC Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) Register Name Register Symbol Reserved Register Start Register End 67 8F Default Value Access Message Signaled Interrupts Capability ID MSI_CAPID 90 91 D005h RO Message Control MC 92 93 0000h RO; R/W Message Address MA 94 97 00000000h R/W; RO Message Data MD 98 99 0000h R/W 9A BF C0 C0 00h R/W; RO C1 CF Reserved Graphics Debug Reset GDRST Reserved Power Management Capabilities ID PMCAPID D0 D1 0001h RO Power Management Capabilities PMCAP D2 D3 0023h RO Power Management Control/Status PMCS D4 D5 0000h RO; R/W D6 E3 E4 E7 00000000h R/W E8 F0 F0 F1 0201h R/W; RO F2 F3 F4 F7 00000000h R/W F8 FB FC FF 00000000h R/W Reserved System Display Event Register ASLE Reserved Graphics Clock Frequency and Gating Control GCFGC Reserved Legacy Backlight Brightness LBB Reserved ASL Storage ASLS NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets. 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only. Datasheet 403 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.1 VID2 - Vendor Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 0-1h 8086h RO 16 bits This register combined with the Device Identification register uniquely identifies any PCI device. Bit Access Default Value 15:0 RO 8086h Description Vendor Identification Number (VID): PCI standard identification for Intel. 21.1.2 DID2 - Device Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 2-3h 2A02h RO 16 bits This register combined with the Vendor Identification register uniquely identifies any PCI device. Bit Access Default Value Description 15:0 RO 2A02h1 Device Identification Number (DID): 2A12h2 Identifier assigned to the (G)MCH core/primary PCI device. NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only 404 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.3 PCICMD2 - PCI Command B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 4-5h 0000h RO; R/W 16 bits This 16-bit register provides basic control over the IGD's ability to respond to PCI cycles. The PCICMD Register in the IGD disables the IGD PCI compliant master accesses to main memory. Bit Access Default Value 15:11 RO 00h 10 R/W 0b Description Reserved Interrupt Disable: This bit disables the device from asserting INTx#. 0: Enable the assertion of this device's INTx# signal. 1: Disable the assertion of this device's INTx# signal. DO_INTx messages will not be sent to DMI. 9 RO 0b Fast Back-to-Back (FB2B): Not Implemented. Hardwired to 0. 8 RO 0b SERR Enable (SERRE): Not Implemented. Hardwired to 0. 7 RO 0b Address/Data Stepping Enable (ADSTEP): Not Implemented. Hardwired to 0. 6 RO 0b Parity Error Enable (PERRE): Not Implemented. Hardwired to 0. Since the IGD belongs to the category of devices that does not corrupt programs or data in system memory or hard drives, the IGD ignores any parity error that it detects and continues with normal operation. 5 RO 0b Video Palette Snooping (VPS): This bit is hardwired to 0 to disable snooping. 4 RO 0b Memory Write and Invalidate Enable (MWIE): Hardwired to 0. The IGD does not support memory write and invalidate commands. 3 RO 0b Special Cycle Enable (SCE): This bit is hardwired to 0. The IGD ignores Special cycles. 2 R/W 0b Bus Master Enable (BME): 0: Disable IGD bus mastering. 1: Enable the IGD to function as a PCI compliant master. Datasheet 405 Internal Graphics Device 2 Configuration Register (D2:F0-F1) Bit Access Default Value 1 R/W 0b Description Memory Access Enable (MAE): This bit controls the IGD's response to memory space accesses. 0: Disable. 1: Enable. 0 R/W 0b I/O Access Enable (IOAE): This bit controls the IGD's response to I/O space accesses. 0: Disable. 1: Enable. 21.1.4 PCISTS2 - PCI Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 6-7h 0090h RO 16 bits PCISTS is a 16-bit status register that reports the occurrence of a PCI compliant master abort and PCI compliant target abort. PCISTS also indicates the DEVSEL# timing that has been set by the IGD. Bit Access Default Value 15 RO 0b Description Detected Parity Error (DPE): Since the IGD does not detect parity, this bit is always hardwired to 0. 14 RO 0b Signaled System Error (SSE): The IGD never asserts SERR#, therefore this bit is hardwired to 0. 13 RO 0b Received Master Abort Status (RMAS): The IGD never gets a Master Abort, therefore this bit is hardwired to 0. 12 RO 0b Received Target Abort Status (RTAS): The IGD never gets a Target Abort, therefore this bit is hardwired to 0. 11 RO 0b Signaled Target Abort Status (STAS): Hardwired to 0. The IGD does not use target abort semantics. 10:9 RO 00b DEVSEL Timing (DEVT): N/A. These bits are hardwired to 00. 8 RO 0b Master Data Parity Error Detected (DPD): Since Parity Error Response is hardwired to disabled (and the IGD does not do any parity detection), this bit is hardwired to 0. 406 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) Bit Access Default Value 7 RO 1b Description Fast Back-to-Back (FB2B): Hardwired to 1. The IGD accepts fast back-to-back when the transactions are not to the same agent. 6 RO 0b User Defined Format (UDF): Hardwired to 0. 5 RO 0b 66-MHz PCI Capable (66C): N/A - Hardwired to 0. 4 RO 1b Capability List (CLIST): This bit is set to 1 to indicate that the register at 34h provides an offset into the function's PCI Configuration Space containing a pointer to the location of the first item in the list. 3 RO 0b Interrupt Status: This bit reflects the state of the interrupt in the device. Only when the Interrupt Disable bit in the command register is a 0 and this Interrupt Status bit is a 1, will the devices INTx# signal be asserted. Setting the Interrupt Disable bit to a 1 has no effect on the state of this bit. 2:0 Datasheet RO 000b Reserved 407 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.5 RID2 - Revision Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 8h 00h RO 8 bits This register contains the revision number for Device 2 Functions 0 and 1. Bit Access Default Value 7:0 RO 00h Description Revision Identification Number (RID): This is an 8-bit value that indicates the revision identification number for the (G)MCH. A register swapping mechanism behind RID register is used to select between a single SRID, or a single CRID to be reflected in the RID register. For the C0 stepping SRID= 03h, CRID= 0Ch. 21.1.6 CC - Class Code B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 9-Bh 030000h RO 24 bits This register contains the device programming interface information related to the Sub-Class Code and Base Class Code definition for the IGD. This register also contains the Base Class Code and the function sub-class in relation to the Base Class Code. Bit Access Default Value 23:16 RO 03h Description Base Class Code (BCC): This is an 8-bit value that indicates the base class code for the (G)MCH. This code has the value 03h, indicating a Display Controller. 15:8 RO 00h Sub-Class Code (SUBCC): Based on Device 0 GGC-GMS bits and GGC-IVD bits. 00h: VGA compatible 80h: Non VGA (GMS = "000" or IVD = 1) 7:0 RO 00h Programming Interface (PI): 00h: Hardwired as a Display controller. 408 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.7 CLS - Cache Line Size B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI Ch 00h RO 8 bits The IGD does not support this register as a PCI slave. Bit Access Default Value 7:0 RO 00h Description Cache Line Size (CLS): This field is hardwired to 0's. The IGD as a PCI compliant master does not use the Memory Write and Invalidate command and, in general, does not perform operations based on cache line size. 21.1.8 MLT2 - Master Latency Timer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI Dh 00h RO 8 bits The IGD does not support the programmability of the master latency timer because it does not perform bursts. Datasheet Bit Access Default Value 7:0 RO 00h Description Master Latency Timer Count Value 409 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.9 HDR2 - Header Type B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI Eh 80h RO 8 bits This register contains the Header Type of the IGD. Bit Access Default Value 7 RO 1b Description Multi Function Status (MFunc): Indicates if the device is a Multi-Function Device. The Value of this register is determined by Device 0, offset 54h, DEVEN[4]. If Device 0 DEVEN[4] is set, the Mfunc bit is also set. 6:0 RO 00h Header Code (H): This is a 7-bit value that indicates the Header Code for the IGD. This code has the value 00h, indicating a type 0 configuration space format. 21.1.10 GTTMMADR - Graphics Translation Table Range Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 10-17h 0000000000000004h RO; R/W 64 bits The base address of Global GTT is located in the Memory Base Address + 512 KB The allocation is for 1024 KB and the base address is defined by bits [35:20]. Bit Access Default Value 63:36 R/W 0000000h 35:20 R/W 0000h Description Reserved Memory Base Address: Set by the OS, these bits correspond to address signals [35:20]. 1 MB combined for MMIO and Global GTT table aperture (512K each). 19:4 RO 0000h Reserved 3 RO 0b Prefetchable Memory 2 RO 1b Memory Type: 0 : To indicate 32-bit base address 1 : To indicate 64-bit base address 410 1 RO 0b Reserved 0 RO 0b Memory/IO Space Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.11 GMADR - Graphics Memory Range Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 18-1Fh 000000000000000Ch R/W; RO; R/W/L 64 bits IGD graphics memory base address is specified in this register. Bit Access Default Value 63:36 R/W 0000000h 35:29 R/W 00h Description Reserved Memory Base Address: Set by the OS, these bits correspond to address signals [35:29]. 28 R/W/L 0b Reserved 27 R/W/L 0b 256-MB Address Mask: This bit is either part of the Memory Base Address (R/W) or part of the Address Mask (RO), depending on the value of MSAC[1:0]. See MSAC (Dev 2, Func 0, offset 66h) for details. 26:4 RO 000000h 3 RO 1b Reserved Prefetchable Memory: Hardwired to 1 to enable prefetching. 2 RO 1b Memory Type: 0 : To indicate 32-bit base address 1 : To indicate 64-bit base address 1 RO 0b Reserved 0 RO 0b Memory/IO Space: Hardwired to 0 to indicate memory space. Datasheet 411 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.12 IOBAR - I/O Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 20-23h 00000001h RO; R/W 32 bits This register provides the Base offset of the I/O registers within Device 2. Bits 15:3 are programmable allowing the I/O Base to be located anywhere in 16bit I/O Address Space. Bits 2:1 are fixed and return zero, bit 0 is hardwired to a one indicating that 8 bytes of I/O space are decoded. If accesses to this IO bar is allowed then the (G)MCH claims all 8-, 16- or 32- bit IO cycles from the CPU that falls within the 8B claimed. Bit Access Default Value Description 31:16 RO 0000h Reserved 15:3 R/W 0000h IO Base Address: Set by the OS, these bits correspond to address signals [15:3]. 2:1 RO 00b Memory Type: Hardwired to 0's to indicate 32-bit address. 0 RO 1b Memory / IO Space: Hardwired to 1 to indicate IO space. 21.1.13 SVID2 - Subsystem Vendor Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 2C-2Dh 0000h R/WO 16 bits Bit Access Default Value 15:0 R/WO 0000h Description Subsystem Vendor ID: This value is used to identify the vendor of the subsystem. This register should be programmed by BIOS during boot-up. Once written, this register becomes Read-Only. This register can only be cleared by a Reset. 412 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.14 SID2 - Subsystem Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 2E-2Fh 0000h R/WO 16 bits Bit Access Default Value 15:0 R/WO 0000h Description Subsystem Identification: This value is used to identify a particular subsystem. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read_Only. This register can only be cleared by a Reset. 21.1.15 ROMADR - Video BIOS ROM Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 30-33h 00000000h RO 32 bits The IGD does not use a separate BIOS ROM, therefore this register is hardwired to 0's. Bit Access Default Value 31:18 RO 0000h Description ROM Base Address: Hardwired to 0's. 17:11 RO 00h Address Mask: Hardwired to 0's to indicate 256-KB address range. 10:1 RO 000h Reserved Hardwired to 0's. 0 RO 0b ROM BIOS Enable: 0 = ROM not accessible. Datasheet 413 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.16 CAPPOINT - Capabilities Pointer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 34h 90h RO 8 bits Bit Access Default Value 7:0 RO 90h Description Capabilities Pointer Value: This field contains an offset into the function's PCI Configuration Space for the first item in the New Capabilities Linked List which is the MSI Capabilities ID register at address 90h or the Power Management Capabilities ID registers at address D0h.The value is determined by CAPL[0]. 21.1.17 INTRLINE - Interrupt Line B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 3Ch 00h R/W 8 bits Bit Access Default Value 7:0 R/W 00h Description Interrupt Connection: Used to communicate interrupt line routing information. POST software writes the routing information into this register as it initializes and configures the system. The value in this register indicates which input of the system interrupt controller that the device's interrupt pin is connected to. 21.1.18 INTRPIN - Interrupt Pin B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 3Dh 01h RO 8 bits Bit Access Default Value 7:0 RO 01h Description Interrupt Pin: As a single function device, the IGD specifies INTA# as its interrupt pin. 01h: INTA#. 414 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.19 MINGNT - Minimum Grant B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 3Eh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Minimum Grant Value: The IGD does not burst as a PCI compliant master. 21.1.20 MAXLAT - Maximum Latency B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 3Fh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Maximum Latency Value: The IGD has no specific requirements for how often it needs to access the PCI bus. 21.1.21 MCAPPTR - Capabilities Pointer (to Mirror of Dev0 CAPID) B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 44h 48h RO 8 bits Bit Access Default Value 7:0 RO 48h Description Capabilities Pointer Value: In this case the first capability is the product-specific Capability Identifier (CAPID0). Datasheet 415 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.22 MGGC - Mirror of Dev0 (G)MCH Graphics Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 52-53h 0030h RO 16 bits . Bit Access Default Value 15:7 RO 000000000b 6:4 RO 011b Description Reserved Graphics Mode Select (GMS): This field is used to select the amount of Main Memory that is preallocated to support the Internal Graphics device in VGA (nonlinear) and Native (linear) modes. The BIOS ensures that memory is pre-allocated only when Internal graphics is enabled. Stolen Memory Bases is located between (TOLUD - SMSize) to TOUD. 000 = No memory pre-allocated. Device 2 (IGD) does not claim VGA cycles (Mem and IO), and the Sub-Class Code field within Device 2 Function 0. Class Code register is 80. 001 = DVMT (UMA) mode, 1 MB of memory pre-allocated for frame buffer. 010 = DVMT (UMA) mode, 4 MB of memory pre-allocated for frame buffer. 011 = DVMT (UMA) mode, 8 MB of memory pre-allocated for frame buffer. 100 = DVMT (UMA) mode, 16 MB of memory pre-allocated for frame buffer. 101 = DVMT (UMA) mode, 32 MB of memory pre-allocated for frame buffer. 110 = DVMT (UMA) mode, 48 MB of memory pre-allocated for frame buffer. 111 = DVMT (UMA) mode, 64 MB of memory pre-allocated for frame buffer. NOTE: This register is locked and becomes Read Only when the D_LCK bit in the SMRAM register is set. Hardware does not clear or set any of these bits automatically based on IGD being disabled/enabled. 3:2 RO 00b 1 RO 0b Reserved IGD VGA Disable (IVD): 1: Disable. Device 2 (IGD) does not claim VGA cycles (Mem and IO), and the Sub-Class Code field within Device 2 Function 0 Class Code register is 80. 0: Enable (Default). Device 2 (IGD) claims VGA memory and IO cycles, the Sub-Class Code within Device 2 Class Code register is 00. 0 416 RO 0b Reserved Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.23 MDEVENdev0F0 - Mirror of Dev0 DEVEN B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 54-57h 0000001Bh RO 32 bits This register allows for enabling/disabling of PCI devices and functions that are within the (G)MCH. This table describes the behavior of all combinations of transactions to devices controlled by this register. Bit Access Default Value Description 31:8 RO 000000h Reserved 7 RO 0b Reserved 6:5 RO 00b Reserved 4 RO 1b Internal Graphics Engine Function 1 (D2F1EN): 0: Bus 0 Device 2 Function 1 is disabled and hidden. 1: Bus 0 Device 2 Function 1 is enabled and visible. If Device 2 Function 0 is disabled and hidden, then Device 2 Function 1 is also disabled and hidden independent of the state of this bit. 3 RO 1b Internal Graphics Engine Function 0 (D2F0EN): 0: Bus 0 Device 2 Function 0 is disabled and hidden. 1: Bus 0 Device 2 Function 0 is enabled and visible. If this (G)MCH does not have internal graphics capability (CAPID0[33] = 1) then Device 2 Function 0 is disabled and hidden independent of the state of this bit. 2 RO 0b Reserved 1 RO 1b PCI Express Graphics Port Enable. (D1EN): 0: Bus 0 Device 1 Function 0 is disabled and hidden. Also gates PCI Express internal clock (lgclk) and asserts PCI Express internal reset (lgrstB). 1: Bus 0 Device 1 Function 0 is enabled and visible. Default value is determined by the device capabilities (CAPID0[37] and CAPID0[35]), SDVO presence HW strap and SDVO/PCIe concurrent HW strap. 0 RO 1b Host Bridge: Bus 0 Device 0 Function 0 may not be disabled and is therefore hardwired to 1. Datasheet 417 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.24 BSM - Base of Stolen Memory B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 5C-63h 0000000000000000h RO 64 bits Graphics Stolen Memory and TSEG are within DRAM space defined under TOLUD. From the top of low used DRAM, (G)MCH claims 1 to 64 MBs of DRAM for internal graphics if enabled. Bit Access Default Value 63:36 RO 0000000h 35:32 RO 0h 31:20 RO 000h Description Reserved Base of Stolen Memory: Base of Stolen Memory (BSM): This register contains bits 31 to 20 of the base address of stolen DRAM memory. The host interface determines the base of graphics stolen memory by subtracting the graphics stolen memory size from TOLUD. See Device 0 TOLUD for more explanation. 19:0 418 RO 00000h Reserved Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.25 MSAC - Multi Size Aperture Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 66h 02h RO; R/W; R/W/L 8 bits This register determines the size of the graphics memory aperture in Function 0 and only in the untrusted space. By default the aperture size is 256 MB. Only the system BIOS will write this register based on pre-boot address allocation efforts, but the graphics may read this register to determine the correct aperture size. System BIOS needs to save this value on boot so that it can reset it correctly during S3 resume. Bit Access Default Value Description 7:4 R/W 0h Scratch Bits Only: 3 RO 0b Reserved 2:1 R/W/L 01b Untrusted Aperture Size (LHSAS): 11: bits [28:27] of GMADR register are made Read only and forced to zero, allowing only 512 MB of GMADR 01 : Illegal programming 00 : Illegal programming 10 : Illegal programming. 0 Datasheet RO 0b Reserved 419 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.26 MSI_CAPID - Message Signaled Interrupts Capability ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 90-91h D005h RO 16 bits When a device supports MSI it can generate an interrupt request to the processor by writing a predefined data item (a message) to a predefined memory address. The reporting of the existence of this capability can be disabled by setting MSICH (CAPL[0[ @ 7Fh). In that case walking this linked list will skip this capability and instead go directly to the PCI PM capability. Bit Access Default Value 15:8 RO D0h Description Pointer to Next Capability: This contains a pointer to the next item in the capabilities list which is the Power Management Capability. 7:0 RO 05h Capability ID: Value of 05h identifies this linked list item (capability structure) as being for MSI registers. 420 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.27 MC - Message Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 92-93h 0000h RO; R/W 16 bits If the device writes the same message multiple times, only one of those messages is ensured to be serviced. If all of them must be serviced, the device must not generate the same message again until the driver services the earlier one. Bit Access Default Value 15:8 RO 00h 7 RO 0b Description Reserved 64-bit Address Capable: Hardwired to 0 to indicate that the function does not implement the upper 32 bits of the Message Address register and is incapable of generating a 64-bit memory address. This may need to change in future implementations when addressable system memory exceeds the 32-bit/4-GB limit. 6:4 R/W 000b Multiple Message Enable (MME): System software programs this field to indicate the actual number of messages allocated to this device. This number will be equal to or less than the number actually requested. The encoding is the same as for the MMC field below. 3:1 RO 000b Multiple Message Capable (MMC): System software reads this field to determine the number of messages being requested by this device. Value: Number of Messages Requested. 000: 1 All of the following are reserved in this implementation: 0 R/W 0b 001: 2 010: 4 011: 8 100: 16 101: 32 110: Reserved 111: Reserved MSI Enable (MSIEN): Controls the ability of this device to generate MSIs. Datasheet 421 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.28 MA - Message Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 94-97h 00000000h R/W; RO 32 bits A read from this register produces undefined results. Bit Access Default Value 31:2 R/W 00000000 h 1:0 RO 00b Description Message Address: Used by system software to assign an MSI address to the device. The device handles an MSI by writing the padded contents of the MD register to this address. Force Dword Align: Hardwired to 0 so that addresses assigned by system software are always aligned on a Dword address boundary. 21.1.29 MD - Message Data B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI 98-99h 0000h R/W 16 bits Bit Access Default Value 15:0 R/W 0000h Description Message Data: Base message data pattern assigned by system software and used to handle an MSI from the device. When the device must generate an interrupt request, it writes a 32-bit value to the memory address specified in the MA register. The upper 16 bits are always set to 0. The lower 16 bits are supplied by this register. 422 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.30 GDRST - Graphics Debug Reset B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI C0h 00h R/W; RO 8 bits Bit Access Default Value 7:2 RO 00b 1 RO 0b Description Reserved Graphics Reset Status: 0: Graphics subsystem not in Reset. 1: Graphics Subsystem in Reset as a result of Graphics Debug Reset. This bit gets is set to a 1 and the Graphics hardware has completed the debug reset sequence and all Graphics assets are in reset. This bit is cleared when Graphics Debug Reset bit is set to a 0. 0 R/W 0b Graphics Debug Reset: 0: Deassert display and render domain reset 1: Assert display and render domain reset Render and Display clock domain resets should be asserted for at least 20 s. Once this bit is set to a 1 all GFX core MMIO registers are returned to power on default state. All Ring buffer pointers are reset, command stream fetches are dropped and ongoing render pipeline processing is halted, state machines and State Variables returned to power on default state, Display and overlay engines are halted (garbage on screen). VGA memory is not available, Store Dwords, interrupts are not ensured to be completed. Device 2 IO registers are not available. Device 2 Config registers are available when Graphics debug reset is asserted. Datasheet 423 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.31 PMCAPID - Power Management Capabilities ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI D0-D1h 0001h RO 16 bits Bit Access Default Value 15:8 RO 00h Description NEXT_PTR: This contains a pointer to next item in capabilities list. This is the final capability in the list and must be set to 00h. 7:0 RO 01h CAP_ID : SIG defines this ID is 01h for power management. 21.1.32 PMCAP - Power Management Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI D2-D3h 0023h RO 16 bits Bit Access Default Value 15:11 RO 00h Description PME Support: This field indicates the power states in which the IGD may assert PME#. Hardwired to 0 to indicate that the IGD does not assert the PME# signal. 10 RO 0b D2: The D2 power management state is not supported. This bit is hardwired to 0. 9 RO 0b D1: Hardwired to 0 to indicate that the D1 power management state is not supported. 8:6 RO 000b 5 RO 1b Reserved Device Specific Initialization (DSI): Hardwired to 1 to indicate that special initialization of the IGD is required before generic class device driver is to use it. 4 RO 0b Auxiliary Power Source: Hardwired to 0. 3 RO 0b PME Clock: Hardwired to 0 to indicate IGD does not support PME# generation. 424 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) Bit Access Default Value 2:0 RO 011b Description Version: A value of 011b indicates that this function complies with revision 1.2 of the PCI Power Management Interface Specification 21.1.33 PMCS - Power Management Control/Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI D4-D5h 0000h RO; R/W 16 bits Bit Access Default Value 15 RO 0b Description PME_Status: This bit is 0 to indicate that IGD does not support PME# generation from D3 (cold). 14:13 RO 00b Reserved 12:9 RO 0h Reserved 8 RO 0b PME_En: This bit is 0 to indicate that PME# assertion from D3 (cold) is disabled. 7:2 RO 00h Reserved 1:0 R/W 00b Power State: This field indicates the current power state of the IGD and can be used to set the IGD into a new power state. If software attempts to write an unsupported state to this field, write operation must complete normally on the bus, but the data is discarded and no state change occurs. On a transition from D3 to D0 the graphics controller is optionally reset to initial values. Bits[1:0] Datasheet Power state 00 D0 Default 01 D1 Not Supported 10 D2 Not Supported 11 D3 425 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.34 ASLE - System Display Event Register B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI E4-E7h 00000000h R/W 32 bits The exact use of these bytes including whether they are addressed as bytes, words, or as a Dword, is not pre-determined but subject to change by driver and System BIOS teams (acting in unison). Bit Access Default Value 31:24 R/W 00h Description ASLE Scratch Trigger3: When written, this scratch byte triggers an interrupt when IEF bit 0 is enabled and IMR bit 0 is unmasked. If written as part of a 16-bit or 32-bit write, only one interrupt is generated in common. 23:16 R/W 00h ASLE Scratch Trigger2: When written, this scratch byte triggers an interrupt when IEF bit 0 is enabled and IMR bit 0 is unmasked. If written as part of a 16-bit or 32-bit write, only one interrupt is generated in common. 15:8 R/W 00h ASLE Scratch Trigger 1: When written, this scratch byte triggers an interrupt when IEF bit 0 is enabled and IMR bit 0 is unmasked. If written as part of a 16-bit or 32-bit write, only one interrupt is generated in common. 7:0 R/W 00h ASLE Scratch Trigger 0: When written, this scratch byte triggers an interrupt when IEF bit 0 is enabled and IMR bit 0 is unmasked. If written as part of a 16-bit or 32-bit write, only one interrupt is generated in common. 426 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.35 GCFGC - Graphics Clock Frequency and Gating Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI F0-F1h 0201h R/W; RO 16 bits Bit Access Default Value Description 15 R/W 0b Reserved 14 R/W 0b Gate Core Display Clock (GCRC) (GCRC): Gate Core Display Clock (GCRC): 0: cdclk is running1:cdclk is gated 13 R/W 0b 12:8 R/W 00010b Reserved (RSVD): Graphics Core Display Clock Select: Software programs this register. 00010 => 320/333 MHz Others => Reserved 7 RO 0b Reserved 6:5 R/W 00b Reserved. 4 R/W 0b Gate Core Render and Sampler Clock (GateCRCLK): Gate Core Render and Sampler Clock (GCRC): 0: crclk, crb2clk and csclk are running 1: crclk, crb2clk and csclk are gated 3:0 R/W 0001b Graphics Core Render Clock Select (CRCLKFREQ): Software programs this register to set the crclk and csclk frequencies. 0010= ~ 250/267 MHz 0011 = ~ 320/333 MHz 0100 = ~ 400/444 MHz 0101= ~ 500/533 MHz Others = Reserved Datasheet 427 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.36 LBB - Legacy Backlight Brightness B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI F4-F7h 00000000h R/W 32 bits Bit Access Default Value 31:24 R/W 00h Description LBPC Scratch Trigger3: When written, this scratch byte triggers an interrupt when LBEE is enabled in the Pipe B Status register and the Display B Event is enabled in IER and unmasked in IMR etc. If written as part of a 16-bit or 32-bit write, only one interrupt is generated in common. 23:16 R/W 00h LBPC Scratch Trigger2: When written, this scratch byte triggers an interrupt when LBEE is enabled in the Pipe B Status register and the Display B Event is enabled in IER and unmasked in IMR etc. If written as part of a 16-bit or 32-bit write, only one interrupt is generated in common. 15:8 R/W 00h LBPC Scratch Trigger1: When written, this scratch byte triggers an interrupt when LBEE is enabled in the Pipe B Status register and the Display B Event is enabled in IER and unmasked in IMR etc. If written as part of a 16-bit or 32-bit write, only one interrupt is generated in common. 7:0 R/W 00h Legacy Backlight Brightness (LBES): The value of zero is the lowest brightness setting and 255 is the brightest. A write to this register will cause a flag to be set (LBES) in the PIPEBSTATUS register and cause an interrupt if Backlight event in the PIPEBSTATUS register and cause an Interrupt if Backlight Event (LBEE) and Display B Event is enabled by software. 428 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.1.37 ASLS - ASL Storage B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI FC-FFh 00000000h R/W; 32 bits This software scratch register only needs to be read/write accessible. The exact bit register usage must be worked out in common between System BIOS and driver software, but storage for switching/indicating up to 6 devices is possible with this amount. For each device, the ASL control method with require two bits for _DOD (BIOS detectable yes or no, VGA/NonVGA), one bit for _DGS (enable/disable requested), and two bits for _DCS (enabled now/disabled now, connected or not). 21.2 Bit Access Default Value 31:0 R/W 00000000h RW according to a software controlled usage to support device switching Device 2 Function 1 PCI configuration Registers Register Name Register Symbol Register Start Register End Default Value Access Vendor Identification VID2 0 1 8086h RO Device Identification DID2 2 3 2A03h1 RO PCI Command PCICMD2 4 5 0000h RO; R/W PCI Status PCISTS2 6 7 0090h RO Revision Identification RID2 8 8 00h RO Class Code Register CC 9 B 038000h RO Cache Line Size CLS C C 00h RO Master Latency Timer MLT2 D D 00h RO Header Type HDR2 E E 80h RO F F 10 17 0000000000 000004h RO; R/W 2A13h2 Reserved Memory Mapped Range Address Datasheet Description MMADR 429 Internal Graphics Device 2 Configuration Register (D2:F0-F1) Register Name Register Symbol Register Start Register End Default Value Access Subsystem Vendor Identification SVID2 2C 2D 0000h RO Subsystem Identification SID2 2E 2F 0000h RO Video BIOS ROM Base Address ROMADR 30 33 00000000h RO Capabilities Pointer CAPPOINT 34 34 D0h RO Minimum Grant MINGNT 3E 3E 00h RO Maximum Latency MAXLAT 3F 3F 00h RO Mirror of Dev0 Capability Pointer MCAPPTR 44 44 48h RO 48 51 Reserved Mirror of Dev0 (G)MCH Graphics Control MGGC 52 53 0030h RO Mirror of Dev0 DEVEN MDEVENdev 0F0 54 57 0000001Bh RO 58 5B 5C 63 0000000000 000000h RO 64 65 66 66 02h RO Reserved Base of Stolen Memory BSM Reserved Multi Size Aperture Control MSAC NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets. 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only. 430 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.1 VID2 - Vendor Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 0-1h 8086h RO 16 bits This register combined with the Device Identification register uniquely identifies any PCI device. Bit Access Default Value 15:0 RO 8086h Description Vendor Identification Number (VID): PCI standard identification for Intel. 21.2.2 DID2 - Device Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 2-3h 2A03h RO 16 bits This register is unique in Function 1 (the Function 0 DID is separate). This difference in Device ID's is necessary for allowing distinct Plug and Play enumeration of Function 1 when both Function 0 and Function 1 have the same class code. Bit Access Default Value 15:0 RO 2A03h1 2 2A13h Description Device Identification Number (DID): This is a 16-bit value assigned to the (G)MCH Graphic device Function 1. NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only Datasheet 431 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.3 PCICMD2 - PCI Command B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 4-5h 0000h RO; R/W 16 bits This 16-bit register provides basic control over the IGD's ability to respond to PCI cycles. The PCICMD Register in the IGD disables the IGD PCI compliant master accesses to main memory. Bit Access Default Value Description 15:11 RO 00h Reserved 10 RO 0b Reserved 9 RO 0b Fast Back-to-Back (FB2B): Not Implemented. Hardwired to 0. 8 RO 0b SERR Enable (SERRE): Not Implemented. Hardwired to 0. 7 RO 0b Address/Data Stepping Enable (ADSTEP): Not Implemented. Hardwired to 0. 6 RO 0b Parity Error Enable (PERRE): Not Implemented. Hardwired to 0. Since the IGD belongs to the category of devices that does not corrupt programs or data in system memory or hard drives, the IGD ignores any parity error that it detects and continues with normal operation. 5 RO 0b VGA Palette Snoop Enable (VGASNOOP): This bit is hardwired to 0 to disable snooping. 4 RO 0b Memory Write and Invalidate Enable (MWIE): Hardwired to 0. The IGD does not support memory write and invalidate commands. 3 RO 0b Special Cycle Enable (SCE): This bit is hardwired to 0. The IGD ignores Special cycles. 2 R/W 0b Bus Master Enable (BME): Set to 1 to enable the IGD to function as a PCI compliant master. Set to 0 to disable IGD bus mastering. 1 R/W 0b Memory Access Enable (MAE): This bit controls the IGD responds to memory space accesses. 0: Disable. 1: Enable. 432 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) Bit Access Default Value 0 R/W 0b Description I/O Access Enable (IOAE): This bit controls the IGD responds to I/O space accesses. 0: Disable. 1: Enable. 21.2.4 PCISTS2 - PCI Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 6-7h 0090h RO 16 bits PCISTS is a 16-bit status register that reports the occurrence of a PCI compliant master abort and PCI compliant target abort. PCISTS also indicates the DEVSEL# timing that has been set by the IGD. Bit Access Default Value 15 RO 0b Description Detected Parity Error (DPE): Since the IGD does not detect parity, this bit is always hardwired to 0. 14 RO 0b Signaled System Error (SSE): The IGD never asserts SERR#, therefore this bit is hardwired to 0. 13 RO 0b Received Master Abort Status (RMAS): The IGD never gets a Master Abort, therefore this bit is hardwired to 0. 12 RO 0b Received Target Abort Status (RTAS: The IGD never gets a Target Abort, therefore this bit is hardwired to 0. 11 RO 0b Signaled Target Abort Status (STAS): Hardwired to 0. The IGD does not use target abort semantics. 10:9 RO 00b DEVSEL Timing (DEVT): These bits are hardwired to 00. 8 RO 0b Master Data Parity Error Detected (DPD): Since Parity Error Response is hardwired to disabled (and the IGD does not do any parity detection), this bit is hardwired to 0. 7 RO 1b Fast Back-to-Back (FB2B): Hardwired to 1. The IGD accepts fast back-to-back when the transactions are not to the same agent. 6 RO 0b User-Defined Format (UDF): Hardwired to 0. Datasheet 433 Internal Graphics Device 2 Configuration Register (D2:F0-F1) Bit Access Default Value 5 RO 0b Description 66-MHz PCI Capable (66C): Hardwired to 0. 4 RO 1b Capability List (CLIST): This bit is set to 1 to indicate that the register at 34h provides an offset into the function PCI Configuration Space containing a pointer to the location of the first item in the list. 3 RO 0b Interrupt Status: Hardwired to 0. 2:0 21.2.5 RO 0h Reserved RID2 - Revision Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 8h 00h RO 8 bits This register contains the revision number for Device 2 Functions 0 and 1. Bit Access Default Value 7:0 RO 00h Description Revision Identification Number (RID): This is an 8-bit value that indicates the revision identification number for the (G)MCH. A register swapping mechanism behind RID register is used to select between a single SRID, or a single CRID to be reflected in the RID register. For the C0 stepping SRID= 03h, CRID= 0Ch. 434 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.6 CC - Class Code Register B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 9-Bh 038000h RO 24 bits This register contains the device programming interface information related to the Sub-Class Code and Base Class Code definition for the IGD. This register also contains the Base Class Code and the function sub-class in relation to the Base Class Code. Bit Access Default Value 23:16 RO 03h Description Base Class Code (BCC): This is an 8-bit value that indicates the base class code for the (G)MCH. This code has the value 03h, indicating a Display Controller. 15:8 RO 80h Sub-Class Code (SUBCC): 80h: Non VGA 7:0 RO 00h Programming Interface (PI): 00h: Hardwired as a Display controller. 21.2.7 CLS - Cache Line Size B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI Ch 00h RO 8 bits Note: The IGD does not support this register as a PCI slave. Bit Access Default Value 7:0 RO 00h Description Cache Line Size (CLS): This field is hardwired to 0's. The IGD as a PCI compliant master does not use the Memory Write and Invalidate command and, in general, does not perform operations based on cache line size. Datasheet 435 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.8 MLT2 - Master Latency Timer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI Dh 00h RO 8 bits Note: The IGD does not support the programmability of the master latency timer because it does not perform bursts. Bit Access Default Value 7:0 RO 00h Description Master Latency Timer Count Value: Hardwired to 0's. 21.2.9 HDR2 - Header Type B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI Eh 80h RO 8 bits This register contains the Header Type of the IGD. Bit Access Default Value 7 RO 1b Description Multi Function Status (MFunc): Indicates if the device is a Multi-Function Device. The Value of this register is determined by Device 0, offset 54h, DEVEN[4]. If Device 0 DEVEN[4] is set, the Mfunc bit is also set. 6:0 RO 00h Header Code (H): This is a 7-bit value that indicates the Header Code for the IGD. This code has the value 00h, indicating a type 0 configuration space format. 436 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.10 MMADR - Memory Mapped Range Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 10-17h 0000000000000004h RO; R/W 64 bits This register requests allocation for the IGD registers and instruction ports. The allocation is for 512 KB and the base address is defined by bits [35:20]. Bit Access Default Value 63:36 R/W 0000000h 35:20 R/W 0000h Description Reserved Memory Base Address: Set by the OS, these bits correspond to address signals [35:20]. 19:4 RO 0000h Address Mask: Hardwired to 0's to indicate 512-KB address range (aligned to 1-M boundary). 3 RO 0b Prefetchable Memory: Hardwired to 0 to prevent prefetching. 2 RO 1b Memory Type: 0: To indicate 32 bit base address. 1: To indicate 64 bit base address. 1 RO 0b Reserved 0 RO 0b Memory / IO Space: Hardwired to 0 to indicate memory space. 21.2.11 SVID2 - Subsystem Vendor Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 2C-2Dh 0000h RO 16 bits Bit Access Default Value 15:0 RO 0000h Description Subsystem Vendor ID: This value is used to identify the vendor of the subsystem. This register should be programmed by BIOS during boot-up. Once written, this register becomes Read_Only. This register can only be cleared by a Reset. Datasheet 437 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.12 SID2 - Subsystem Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 2E-2Fh 0000h RO 16 bits Bit Access Default Value 15:0 RO 0000h Description Subsystem Identification: This value is used to identify a particular subsystem. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read_Only. This register can only be cleared by a Reset. 21.2.13 ROMADR - Video BIOS ROM Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 30-33h 00000000h RO 32 bits Note: The IGD does not use a separate BIOS ROM, therefore this register is hardwired to 0's. Bit Access Default Value 31:18 RO 0000h Description ROM Base Address: Hardwired to 0's. 17:11 RO 00h Address Mask: Hardwired to 0's to indicate 256-KB address range. 10:1 RO 000h Reserved: Hardwired to 0's. 0 RO 0b ROM BIOS Enable: 0 = ROM not accessible. 438 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.14 CAPPOINT - Capabilities Pointer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 34h D0h RO 8 bits Bit Access Default Value 7:0 RO D0h Description Capabilities Pointer Value (CPV): This field contains an offset into the function's PCI Configuration Space for the first item in the New Capabilities Linked List which is the Power Management Capabilities ID registers at address D0h. 21.2.15 MINGNT - Minimum Grant B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 3Eh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Minimum Grant Value: The IGD does not burst as a PCI compliant master. 21.2.16 MAXLAT - Maximum Latency B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 3Fh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Maximum Latency Value: The IGD has no specific requirements for how often it needs to access the PCI bus. Datasheet 439 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.17 MCAPPTR - Mirror of Dev0 Capability Pointer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 44h 48h RO 8 bits Bit Access Default Value 7:0 RO 48h Description Capabilities Pointer Value: In this case the first capability is the product-specific Capability Identifier (CAPID0). 21.2.18 MGGC - Mirror of Dev0 (G)MCH Graphics Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 52-53h 0030h RO 16 bits . 440 Bit Access Default Value 15:7 RO 00000000 0b Description Reserved Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) Bit Access Default Value 6:4 RO 011b Description Graphics Mode Select (GMS): This field is used to select the amount of Main Memory that is pre-allocated to support the Internal Graphics device in VGA (non-linear) and Native (linear) modes. The BIOS ensures that memory is pre-allocated only when Internal graphics is enabled. Stolen Memory Bases is located between (TOLUD - SMSize) to TOUD. 000 = No memory pre-allocated. Device 2 (IGD) does not claim VGA cycles (Mem and IO), and the Sub-Class Code field within Device 2 Function 0. Class Code register is 80. 001 = DVMT (UMA) mode, 1 MB of memory pre-allocated for frame buffer. 010 = DVMT (UMA) mode, 4 MB of memory pre-allocated for frame buffer. 011 = DVMT (UMA) mode, 8 MB of memory pre-allocated for frame buffer. 100 = DVMT (UMA) mode, 16 MB of memory pre-allocated for frame buffer. 101 = DVMT (UMA) mode, 32 MB of memory pre-allocated for frame buffer. 110 = DVMT (UMA) mode, 48 MB of memory pre-allocated for frame buffer. 111 = DVMT (UMA) mode, 64 MB of memory pre-allocated for frame buffer. This register is locked and becomes Read Only when the D_LCK bit in the SMRAM register is set. Hardware does not clear or set any of these bits automatically based on IGD being disabled/enabled. 3:2 RO 00b 1 RO 0b Reserved IGD VGA Disable (IVD): 0: Enable (Default). Device 2 (IGD) claims VGA memory and IO cycles, the Sub-Class Code within Device 2 Class Code register is 00. 1: Disable. Device 2 (IGD) does not claim VGA cycles (Mem and IO), and the Sub-Class Code field within Device 2 Function 0 Class Code register is 80. 0 Datasheet RO 0b Reserved 441 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.19 MDEVENdev0F0 - Mirror of Dev0 DEVEN B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 54-57h 0000001Bh RO 32 bits This register allows for enabling/disabling of PCI devices and functions that are within the (G)MCH. This table describes the behavior of all combinations of transactions to devices controlled by this register. Bit Access Default Value Description 31:8 RO 000000h Reserved 7 RO 0b Reserved 6:5 RO 00b Reserved 4 RO 1b Internal Graphics Engine Function 1 (D2F1EN): 0: Bus 0 Device 2 Function 1 is disabled and hidden 1: Bus 0 Device 2 Function 1 is enabled and visible If Device 2 Function 0 is disabled and hidden, then Device 2 Function 1 is also disabled and hidden independent of the state of this bit. 3 RO 1b Internal Graphics Engine Function 0 (D2F0EN): 0: Bus 0 Device 2 Function 0 is disabled and hidden 1: Bus 0 Device 2 Function 0 is enabled and visible If this (G)MCH does not have internal graphics capability (CAPID0[33] = 1) then Device 2 Function 0 is disabled and hidden independent of the state of this bit. 2 RO 0b Reserved 1 RO 1b PCI Express Graphics Port Enable. (D1EN): 0: Bus 0 Device 1 Function 0 is disabled and hidden. 1: Bus 0 Device 1 Function 0 is enabled and visible. Default value is determined by the device capabilities, SDVO presence HW strap and SDVO/PCIe concurrent HW strap. Device 1 is Disabled on Reset if {the SDVO present strap is sampled high and the SDVO/PCIe concurrent strap is sampled low}. 0 RO 1b Host Bridge: Bus 0 Device 0 Function 0 may not be disabled and is therefore hardwired to 1. 442 Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.20 BSM - Base of Stolen Memory B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 5C-63h 0000000000000000h RO 64 bits Graphics Stolen Memory and TSEG are within DRAM space defined under TOLUD. From the top of low used DRAM, (G)MCH claims 1 to 64MBs of DRAM for internal graphics if enabled. Bit Access Default Value 63:36 RO 0000000h 35:32 RO 0h 31:20 RO 000h Description Reserved Base of Stolen Memory Base of Stolen Memory (BSM): This register contains bits 31 to 20 of the base address of stolen DRAM memory. The host interface determines the base of graphics stolen memory by subtracting the graphics stolen memory size from TOLUD. See Device 0 TOLUD for more explanation. 19:0 Datasheet RO 00000h Reserved 443 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.2.21 MSAC - Multi Size Aperture Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/1/PCI 66h 02h RO 8 bits This register determines the size of the graphics memory aperture in Function 0 and only in the untrusted space. By default, the aperture size is 256 MB. Only the system BIOS will write this register based on pre-boot address allocation efforts, but the graphics may read this register to determine the correct aperture size. System BIOS needs to save this value on boot so that it can reset it correctly during S3 resume. Bit Access Default Value 7:4 RO 0h Description Scratch Bits Only: Have no physical effect on hardware. 3 RO 0b 2:1 RO 01b Reserved Untrusted Aperture Size (LHSAS): 11: bits [28:27] of GMADR register are made Read only and forced to zero, allowing only 512 MB of GMADR 01: bit [28] of GMADR is made R/W and bit [27] of GMADR is forced to zero allowing 256 MB of GMADR 00: bits [28:27] of GMADR register are made R/W allowing 128 MB of GMADR 10: Illegal programming. 0 444 RO 0b Reserved Datasheet Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.3 Device 2 Function 0 -PCI I/O Registers The following are not PCI config registers. They are I/O registers. This mechanism allows access to internal graphics MMIO registers must not be used to access VGA I/O registers which are mapped through the MMIO space. VGA registers must be access directly through the dedicated VGA IO ports. 21.3.1 Device 2 Function 0 IO Configuration Registers Register Name 21.3.2 Register Symbol Register Start Register End Default Value Access MMIO Address Register Index 0 3 00000000h R/W MMIO Data Register Data 4 7 00000000h R/W Index - MMIO Address Register B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI IO 0-3h 00000000h R/W 32 bits MMIO_INDEX: A 32 bit IO write to this port loads the offset of the MMIO register that needs to be accessed. An IO Read returns the current value of this register. An 8/16 bit IO write to this register is completed by the (G)MCH but does not update this register. This mechanism to access internal graphics MMIO registers must not be used to access VGA IO registers which are mapped through the MMIO space. VGA registers must be accessed directly through the dedicated VGA IO ports. Bit Access Default Value 31:2 R/W 00000000 h 1:0 R/W 00b Description Reserved Target: 00: Others: Datasheet MMIO Registers. Reserved 445 Internal Graphics Device 2 Configuration Register (D2:F0-F1) 21.3.3 Data - MMIO Data Register B/D/F/Type: Address Offset: Default Value: Access: Size: 0/2/0/PCI IO 4-7h 00000000h R/W 32 bits MMIO_DATA: A 32 bit IO write to this port is re-directed to the MMIO register/GTT location pointed to by the MMIO-index register. A 32 bit IO read to this port is redirected to the MMIO register address pointed to by the MMIO-index register regardless of the target selection in MMIO_INDEX (1:0). 8 or 16 bit IO writes are completed by the (G)MCH and may have un-intended side effects, hence must not be used to access the data port. 8 or 16 bit IO reads are completed normally. Note: If the target field in MMIO Index selects "GTT", reads to MMIO data return 0's and not the value programmed in the GTT memory corresponding to the offset programmed in MMIO index. 446 Bit Access Default Value 31:0 R/W 00000000h Description MMIO Data Window (DATA) Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22 Intel(R) Management Engine Subsystem PCI Device 3 22.1 MEI1 PCI Device 3 Function 0 Register Name Identifiers Register Symbol ID Register Start 0 Register End Default Value 3 2A04h1 Access RO 2 2A14h Command CMD 4 5 0000h RO; RW Device Status STS 6 7 0010h RO Revision ID RID 8 8 00h RO Class Code CC 9 B 000000h RO Cache Line Size CLS C C 00h RO Master Latency Timer MLT D D 00h RO Header Type HTYPE E E 80h RO F F 10 17 000000000000 0004h RO; RW 18 2B 2C 2F 00000000h RWO 30 33 34 34 50h RO 35 3B Reserved MEI MMIO Base Address MEI_MBAR Reserved Sub System Identifiers SS Reserved Capabilities Pointer CAP Reserved Datasheet Interrupt Information INTR 3C 3D 0100h RO; RW Minimum Grant MGNT 3E 3E 00h RO Maximum Latency MLAT 3F 3F 00h RO Host Firmware Status HFS 40 43 00000000h RO 447 Intel(R) Management Engine Subsystem PCI Device 3 Register Name Register Symbol Reserved Register Start Register End 44 4F Default Value Access PCI Power Management Capability ID PID 50 51 8C01h RO PCI Power Management Capabilities PC 52 53 C803h RO PCI Power Management Control and Status PMCS 54 55 0008h RWC; RO; RW 56 8B Reserved Message Signaled Interrupt Identifiers MID 8C 8D 0005h RO Message Signaled Interrupt Message Control MC 8E 8F 0080h RO; RW Message Signaled Interrupt Message Address MA 90 93 00000000h RW; RO 94 97 Reserved Message Signaled Interrupt Message Data MD 98 99 0000h RW Intel(R) MEI Interrupt Delivery Mode HIDM A0 A0 00h RW NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets. 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only. 448 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.1.1 ID - Identifiers B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 0-3h 29748086h RO 32 bits Bit Access Default Value 31:16 RO 2A04h1 Device ID (DID): 2A14h2 Indicates what device number assigned for the Intel(R) Management Engine subsystem. 8086h Vendor ID (VID): 15:0 RO Description 16-bit field which indicates Intel is the vendor, assigned by the PCI SIG. NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets. 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only. 22.1.2 CMD - Command B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 4-5h 0000h RO; RW 16 bits Bit Access Default Value 15:11 RO 00000b 10 RW 0b Description Reserved Interrupt Disable (ID): Disables this device from generating PCI line based interrupts. This bit does not have any effect on MSI operation. 9 RO 0b Fast Back-to-Back Enable (FBE): Not implemented, hardwired to 0. 8 RO 0b SERR# Enable (SEE): Not implemented, hardwired to 0. 7 RO 0b Wait Cycle Enable (WCC): Not implemented, hardwired to 0. 6 RO 0b Parity Error Response Enable (PEE): Not implemented, hardwired to 0. 5 RO 0b VGA Palette Snooping Enable (VGA): Not implemented, hardwired to 0 Datasheet 449 Intel(R) Management Engine Subsystem PCI Device 3 Bit Access Default Value 4 RO 0b Description Memory Write and Invalidate Enable (MWIE): Not implemented, hardwired to 0. 3 RO 0b Special Cycle Enable (SCE): Not implemented, hardwired to 0. 2 RW 0b Bus Master Enable (BME): Controls the Intel(R) MEI host controller's ability to act as a system memory master for data transfers. When this bit is cleared, Intel MEI bus master activity stops and any active DMA engines return to an idle condition. This bit is made visible to firmware through the H_PCI_CSR register, and changes to this bit may be configured by the H_PCI_CSR register to generate an Intel(R) Management Engine MSI. When this bit is 0, Intel MEI is blocked from generating MSI to the host CPU. 1 RW 0b Memory Space Enable (MSE): Controls access to the Intel MEI host controller's memory mapped register space. 0 RO 0b I/O Space Enable (IOSE): Not implemented, hardwired to 0. 22.1.3 STS - Device Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 6-7h 0010h RO 16 bits Bit Access Default Value 15 RO 0b Description Detected Parity Error (DPE): Not implemented, hardwired to 0. 14 RO 0b Signaled System Error (SSE): Not implemented, hardwired to 0. 13 RO 0b Received Master-Abort (RMA): Not implemented, hardwired to 0. 12 RO 0b Received Target Abort (RTA): Not implemented, hardwired to 0. 11 RO 0b Signaled Target-Abort (STA): Not implemented, hardwired to 0. 10:9 RO 00b DEVSEL# Timing (DEVT): These bits are hardwired to 00. 450 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 Bit Access Default Value 8 RO 0b Description Master Data Parity Error Detected (DPD): Not implemented, hardwired to 0. 7 RO 0b Fast Back-to-Back Capable (FBC): Not implemented, hardwired to 0. 6 RO 0b Reserved 5 RO 0b 66-MHz Capable (C66): Not implemented, hardwired to 0. 4 RO 1b Capabilities List (CL): Indicates the presence of a capabilities list, hardwired to 1. 3 RO 0b Interrupt Status (IS): Indicates the interrupt status of the device (1 = asserted). 2:0 22.1.4 RO 000b Reserved RID - Revision ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 8h 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Revision ID (RID): This is an 8-bit value that indicates the revision identification number for the (G)MCH. A register swapping mechanism behind RID register is used to select between a single SRID, or a single CRID to be reflected in the RID register. For the C0 stepping SRID= 03h, CRID= 0Ch. Datasheet 451 Intel(R) Management Engine Subsystem PCI Device 3 22.1.5 CC - Class Code B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 9-Bh 000000h RO 24 bits Bit Access Default Value 23:16 RO 00h Description Base Class Code (BCC): Indicates the base class code of the Intel(R) MEI host controller device. 15:8 RO 00h Sub Class Code (SCC): Indicates the sub class code of the Intel MEI host controller device. 7:0 RO 00h Programming Interface (PI): Indicates the programming interface of the Intel MEI host controller device. 22.1.6 CLS - Cache Line Size B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI Ch 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Cache Line Size (CLS): Not implemented, hardwired to 0. 22.1.7 MLT - Master Latency Timer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI Dh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Master Latency Timer (MLT): Not implemented, hardwired to 0. 452 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.1.8 HTYPE - Header Type B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI Eh 80h RO 8 bits Bit Access Default Value 7 RO 1b Description Multi-Function Device (MFD): Indicates the Intel(R) MEI host controller is part of a multi-function device. 6:0 RO 0000000b Header Layout (HL): Indicates that the Intel MEI host controller uses a target device layout. 22.1.9 MEI_MBAR - MEI MMIO Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 10-17h 0000000000000004h RO; RW 64 bits Bit Access Default Value 63:4 RW 00000000 0000000h 3 RO 0b Description Base Address (BA): Base address of register memory space. Prefetchable (PF): Indicates that this range is not prefetchable 2:1 RO 10b Type (TP): Indicates that this range can be mapped anywhere in 64-bit address space. 0 RO 0b Resource Type Indicator (RTE): Indicates a request for register memory space. Datasheet 453 Intel(R) Management Engine Subsystem PCI Device 3 22.1.10 SS - Sub System Identifiers B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 2C-2Fh 00000000h RWO; 32 bits Bit Access Default Value 31:16 RWO 0000h Description Subsystem ID (SSID): Indicates the sub-system identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. 15:0 RWO 0000h Subsystem Vendor ID (SSVID): Indicates the sub-system vendor identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. 22.1.11 CAP - Capabilities Pointer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 34h 50h RO 8 bits Bit Access Default Value 7:0 RO 50h Description Capability Pointer (CP): Indicates the first capability pointer offset. It points to the PCI power management capability offset. 454 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.1.12 INTR - Interrupt Information B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 3C-3Dh 0100h RO; RW 16 bits Bit Access Default Value 15:8 RO 01h Description Interrupt Pin (IPIN): This indicates the interrupt pin the Intel(R) MEI host controller uses. The value of 01h selects INTA# interrupt pin. NOTE: As Intel MEI is an internal device in the GMCH, the INTA# pin is implemented as an INTA# message to the ICH. 7:0 RW 00h Interrupt Line (ILINE): Software written value to indicate which interrupt line (vector) the interrupt is connected to. 22.1.13 MGNT - Minimum Grant B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 3Eh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Grant (GNT): Not implemented, hardwired to 0. 22.1.14 MLAT - Maximum Latency B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 3Fh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Latency (LAT): Not implemented, hardwired to 0. Datasheet 455 Intel(R) Management Engine Subsystem PCI Device 3 22.1.15 HFS - Host Firmware Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 40-43h 00000000h RO; 32 bits Bit Access Default Value 31:0 RO 00000000h Description Firmware Status Host Access (FS_HA): Reserved. 22.1.16 PID - PCI Power Management Capability ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 50-51h 8C01h RO 16 bits Bit Access Default Value 15:8 RO 8Ch Description Next Capability (NEXT): Indicates the location of the next capability item in the list. This is the Message Signaled Interrupts capability. 7:0 RO 01h Cap ID (CID): Indicates that this pointer is a PCI power management. 456 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.1.17 PC - PCI Power Management Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 52-53h C803h RO 16 bits Bit Access Default Value 15:11 RO 11001b Description PME_Support (PSUP): Indicates the states that can generate PME#. Intel(R) Management Engine Interface can assert PME# from any D-state except D1 or D2 which are not supported by Intel MEI. 10 RO 0b D2_Support (D2S): The D2 state is not supported for the Intel MEI host controller. 9 RO 0b D1_Support (D1S): The D1 state is not supported for the Intel MEI host controller. 8:6 RO 000b 5 RO 0b Reserved Device Specific Initialization (DSI): Indicates whether device-specific initialization is required. 4 RO 0b Reserved 3 RO 0b PME Clock (PMEC): Indicates that PCI clock is not required to generate PME#. 2:0 RO 011b Version (VS): Indicates support for Revision 1.2 of the PCI Power Management Specification. Datasheet 457 Intel(R) Management Engine Subsystem PCI Device 3 22.1.18 PMCS - PCI Power Management Control and Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 54-55h 0008h RWC; RO; RW 16 bits Bit Access Default Value 15 RWC 0b Description PME Status (PMES): The PME Status bit in Intel(R) MEI space can be set to 1 by FW performing a write into AUX register to set PMES. This bit is cleared by host CPU writing a 1 to it. FW cannot clear this bit. Host CPU writes with value 0 have no effect on this bit. This bit is reset to 0 by MRST# 14:9 RO 000000b 8 RW 0b Reserved PME Enable (PMEE): This bit is read/write, under control of host SW. It does not directly have an effect on PME events. This bit is reset to 0 by MRST# 7:4 RO 0000b 3 RO 1b Reserved No_Soft_Reset (NSR): This bit indicates that when the Intel MEI host controller is transitioning from D3hot to D0 due to power state command, it does not perform an internal reset. 2 RO 0b 1:0 RW 00b Reserved Power State (PS): This field is used both to determine the current power state of the Intel MEI host controller and to set a new power state. The values are: 00 - D0 state 11 - D3HOT state 458 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.1.19 MID - Message Signaled Interrupt Identifiers B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 8C-8Dh 0005h RO 16 bits Bit Access Default Value 15:8 RO 00h Description Next Pointer (NEXT): Indicates the next item in the list. This can be other capability pointers (such as PCI-Express) or it can be the last item in the list. 7:0 RO 05h Capability ID (CID): Capabilities ID indicates MSI. 22.1.20 MC - Message Signaled Interrupt Message Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 8E-8Fh 0080h RO; RW 16 bits Bit Access Default Value 15:8 RO 00h 7 RO 1b Description Reserved 64-Bit Address Capable (C64): Specifies whether capable of generating 64-bit messages. 6:4 RO 000b Multiple Message Enable (MME): Not implemented, hardwired to 0. 3:1 RO 000b Multiple Message Capable (MMC): Not implemented, hardwired to 0. 0 RW 0b MSI Enable (MSIE): If set, MSI is enabled and traditional interrupt pins are not used to generate interrupts. Datasheet 459 Intel(R) Management Engine Subsystem PCI Device 3 22.1.21 MA - Message Signaled Interrupt Message Address B/D/F/Type: Address Offset: Default Value: Access: Size: Bit Access Default Value 31:2 RW 00000000 h 1:0 22.1.22 0/3/0/PCI 90-93h 00000000h RW; RO 32 bits RO 00b Description Address (ADDR): Lower 32 bits of the system specified message address, always DW-aligned. Reserved MD - Message Signaled Interrupt Message Data B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/0/PCI 98-99h 0000h RW 16 bits Bit Access Default Value 15:0 RW 0000h Description Data (Data): This 16-bit field is programmed by system software if MSI is enabled. Its content is driven onto the FSB during the data phase of the MSI memory write transaction. 22.1.23 HIDM - MEI Interrupt Delivery Mode B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/3/0/PCI A0h 00h RW 8 bits 00h Bit Access Default Value 7:2 RO 0h 1:0 RW 00b Description Reserved MEI Interrupt Delivery Mode (HIDM): These bits control what type of interrupt the Intel(R) MEI will send: 00: Generate Legacy or MSI interrupt 01: Generate SCI 10: Generate SMI 460 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.2 MEI2 PCI Device 3 Function 1 Register Name Identifiers Register Symbol ID Register Start 0 Register End Default Value 3 2A05h1 Access RO 2A15h2 Command CMD 4 5 0000h RO; RW Device Status STS 6 7 0010h RO Revision ID RID 8 8 00h RO Class Code CC 9 B 000000h RO Cache Line Size CLS C C 00h RO Master Latency Timer MLT D D 00h RO Header Type HTYPE E E 80h RO F F 10 17 000000000000 0004h RO; RW 18 2B 2C 2F 00000000h RWO 30 33 34 34 50h RO 35 3B Reserved MEI MMIO Base Address MEI_MBAR Reserved Sub System Identifiers SS Reserved Capabilities Pointer CAP Reserved Interrupt Information INTR 3C 3D 0100h RW; RO Minimum Grant MGNT 3E 3E 00h RO Maximum Latency MLAT 3F 3F 00h RO Host Firmware Status HFS 40 43 00000000h RO 44 4F Reserved PCI Power Management Capability ID PID 50 51 8C01h RO PCI Power Management Capabilities PC 52 53 C803h RO Datasheet 461 Intel(R) Management Engine Subsystem PCI Device 3 Register Name PCI Power Management Control and Status Register Symbol PMCS Reserved Register Start Register End Default Value Access 54 55 0008h RW; RWC; RO 56 8B Message Signaled Interrupt Identifiers MID 8C 8D 0005h RO Message Signaled Interrupt Message Control MC 8E 8F 0080h RO, RW Message Signaled Interrupt Message Address MA 90 93 00000000h RO, RW 94 97 Reserved Message Signaled Interrupt Message Data MD 98 99 0000h RW MEI Interrupt Delivery Mode HIDM A0 A0 00h RW NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only 462 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.2.1 ID - Identifiers B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 0-3h 29058086h RO 32 bits Bit Access Default Value 31:16 RO 2A05h1 Device ID (DID): 2A15h2 Indicates what device number assigned by Intel. 8086h Vendor ID (VID): 15:0 RO Description 16-bit field which indicates Intel is the vendor, assigned by the PCI SIG. NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only Datasheet 463 Intel(R) Management Engine Subsystem PCI Device 3 22.2.2 CMD - Command B/D/F/Type: Address Offset: Default Value: Access: Size: Bit 0/3/1/PCI 4-5h 0000h RO; RW 16 bits Access Default Value Description 15:11 RO 00000b 10 RW 0b Interrupt Disable (ID): Disables this device from generating PCI line based interrupts. This bit does not have any effect on MSI operation. 9 RO 0b Fast Back-to-Back Enable (FBE): 8 RO 0b Reserved Not implemented, hardwired to 0. SERR# Enable (SEE): Not implemented, hardwired to 0. 7 RO 0b 6 RO 0b Wait Cycle Enable (WCC): Not implemented, hardwired to 0. Parity Error Response Enable (PEE): Not implemented, hardwired to 0. 5 RO 0b VGA Palette Snooping Enable (VGA): Not implemented, hardwired to 0 4 RO 0b Memory Write and Invalidate Enable (MWIE): Not implemented, hardwired to 0. 3 RO 0b Special Cycle Enable (SCE): Not implemented, hardwired to 0. 2 RW 0b Bus Master Enable (BME): Controls the Intel(R) MEI host controller's ability to act as a system memory master for data transfers. When this bit is cleared, Intel MEI bus master activity stops and any active DMA engines return to an idle condition. This bit is made visible to firmware through the H_PCI_CSR register, and changes to this bit may be configured by the H_PCI_CSR register to generate an Intel(R) Management Engine ME MSI. When this bit is 0, Intel MEI is blocked from generating MSI to the host CPU. 1 RW 0b Memory Space Enable (MSE): Controls access to the Intel MEI host controller's memory mapped register space. 0 RO 0b I/O Space Enable (IOSE): Not implemented, hardwired to 0. 464 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.2.3 STS - Device Status B/D/F/Type: Address Offset: Default Value: Access: Size: Bit Access Default Value 15 RO 0b 0/3/1/PCI 6-7h 0010h RO 16 bits Description Detected Parity Error (DPE): Not implemented, hardwired to 0. 14 RO 0b Signaled System Error (SSE): Not implemented, hardwired to 0. 13 RO 0b Received Master-Abort (RMA): Not implemented, hardwired to 0. 12 RO 0b Received Target Abort (RTA): Not implemented, hardwired to 0. 11 RO 0b Signaled Target-Abort (STA): Not implemented, hardwired to 0. 10:9 RO 00b DEVSEL# Timing (DEVT): These bits are hardwired to 00. 8 RO 0b Master Data Parity Error Detected (DPD): Not implemented, hardwired to 0. 7 RO 0b Fast Back-to-Back Capable (FBC): Not implemented, hardwired to 0. 6 RO 0b Reserved 5 RO 0b 66-MHz Capable (C66): Not implemented, hardwired to 0. 4 RO 1b Capabilities List (CL): Indicates the presence of a capabilities list, hardwired to 1. 3 RO 0b Interrupt Status (IS): Indicates the interrupt status of the device (1 = asserted). 2:0 Datasheet RO 000b Reserved 465 Intel(R) Management Engine Subsystem PCI Device 3 22.2.4 RID - Revision ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 8h 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Revision ID (RID): This is an 8-bit value that indicates the revision identification number for the (G)MCH. A register swapping mechanism behind RID register is used to select between a single SRID, or a single CRID to be reflected in the RID register. For the C0 stepping SRID= 03h, CRID= 0Ch.. 22.2.5 CC - Class Code B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 9-Bh 000000h RO 24 bits Bit Access Default Value 23:16 RO 00h Description Base Class Code (BCC): Indicates the base class code of the Intel(R) MEI host controller device. 15:8 RO 00h Sub Class Code (SCC): Indicates the sub class code of the Intel MEI host controller device. 7:0 RO 00h Programming Interface (PI): Indicates the programming interface of the Intel MEI host controller device. 466 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.2.6 CLS - Cache Line Size B/D/F/Type: Address Offset: Default Value: Access: Size: 22.2.7 0/3/1/PCI Ch 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Cache Line Size (CLS): Not implemented, hardwired to 0. MLT - Master Latency Timer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI Dh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Master Latency Timer (MLT): Not implemented, hardwired to 0. 22.2.8 HTYPE - Header Type B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI Eh 80h RO 8 bits Bit Access Default Value 7 RO 1b Description Multi-Function Device (MFD): Indicates the Intel(R) MEI host controller is part of a multifunction device. 6:0 RO 0000000b Header Layout (HL): Indicates that the Intel MEI host controller uses a target device layout. Datasheet 467 Intel(R) Management Engine Subsystem PCI Device 3 22.2.9 MEI_MBAR - MEI MMIO Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 10-17h 0000000000000004h RO; RW 64 bits Bit Access Default Value 63:4 RW 00000000 0000000h 3 RO 0b Description Base Address (BA): Base address of register memory space. Prefetchable (PF): Indicates that this range is not prefetchable 2:1 RO 10b Type (TP): Indicates that this range can be mapped anywhere in 32-bit address space 0 RO 0b Resource Type Indicator (RTE): Indicates a request for register memory space. 22.2.10 SS - Sub System Identifiers B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 2C-2Fh 00000000h RWO 32 bits Bit Access Default Value 31:16 RWO 0000h Description Subsystem ID (SSID): Indicates the sub-system identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. 15:0 RWO 0000h Subsystem Vendor ID (SSVID): Indicates the sub-system vendor identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. 468 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.2.11 CAP - Capabilities Pointer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 34h 50h RO 8 bits Bit Access Default Value 7:0 RO 50h Description Capability Pointer (CP): Indicates the first capability pointer offset. It points to the PCI power management capability offset. 22.2.12 INTR - Interrupt Information B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 3C-3Dh 0100h RW; RO 16 bits Bit Access Default Value 15:8 RO 01h Description Interrupt Pin (IPIN): This indicates the interrupt pin the Intel(R) MEI host controller uses. The value of 01h selects INTA# interrupt pin. NOTE: As Intel MEI is an internal device in the GMCH, the INTA# pin is implemented as an INTA# message to the ICH. 7:0 RW 00h Interrupt Line (ILINE): Software written value to indicate which interrupt line (vector) the interrupt is connected to. No hardware action is taken on this register. 22.2.13 MGNT - Minimum Grant B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 3Eh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Grant (GNT): Not implemented, hardwired to 0. Datasheet 469 Intel(R) Management Engine Subsystem PCI Device 3 22.2.14 MLAT - Maximum Latency B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 3Fh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Latency (LAT): Not implemented, hardwired to 0. 22.2.15 HFS - Host Firmware Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 40-43h 00000000h RO 32 bits Bit Access Default Value 31:0 RO 00000000h Description Firmware Status Host Access (FS_HA): Indicates current status of the firmware for the Intel(R) MEI controller. 22.2.16 PID - PCI Power Management Capability ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 50-51h 8C01h RO 16 bits Bit Access Default Value 15:8 RO 8Ch Description Next Capability (NEXT): Indicates the location of the next capability item in the list. This is the Message Signaled Interrupts capability. 7:0 RO 01h Cap ID (CID): Indicates that this pointer is a PCI power management. 470 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.2.17 PC - PCI Power Management Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 52-53h C803h RO 16 bits Bit Access Default Value 15:11 RO 11001b Description PME_Support (PSUP): Indicates the states that can generate PME#. Intel(R) MEI can assert PME# from any D-state except D1 or D2 which are not supported by Intel MEI. 10 RO 0b D2_Support (D2S): The D2 state is not supported for the Intel MEI host controller. 9 RO 0b D1_Support (D1S): The D1 state is not supported for the Intel MEI host controller. 8:6 RO 000b 5 RO 0b Reserved Device Specific Initialization (DSI): Indicates whether device-specific initialization is required. 4 RO 0b Reserved 3 RO 0b PME Clock (PMEC): Indicates that PCI clock is not required to generate PME#. 2:0 RO 011b Version (VS): Indicates support for Revision 1.2 of the PCI Power Management Specification. Datasheet 471 Intel(R) Management Engine Subsystem PCI Device 3 22.2.18 PMCS - PCI Power Management Control and Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 54-55h 0008h RW; RWC; RO 16 bits Bit Access Default Value 15 RWC 0b Description PME Status (PMES): The PME Status bit in Intel(R) MEI space can be set to 1 by ARC FW performing a write into AUX register to set PMES. This bit is cleared by host CPU writing a 1 to it. ARC cannot clear this bit. Host CPU writes with value 0 have no effect on this bit. This bit is reset to 0 by MRST# 14:9 RO 000000b Reserved 8 RW 0b 7:4 RO 0000b 3 RO 1b No_Soft_Reset (NSR): This bit indicates that when the Intel MEI host controller is transitioning from D3hot to D0 due to power state command, it does not perform and internal reset. Configuration context is pRSVD (RSVD): Reserved 2 RO 0b Reserved 1:0 RW 00b PME Enable (PMEE): This bit is read/write, under control of host SW. It does not directly have an effect on PME events. However, this bit is shadowed into AUX space so ARC FW can monitor it. The ARC FW is responsible for ensuring that FW does not cause the PME-S bit to transition to 1 while the PMEE bit is 0, indicating that host SW had disabled PME. This bit is reset to 0 by MRST# Reserved Power State (PS): This field is used both to determine the current power state of the Intel MEI host controller and to set a new power state. The values are: 00 - D0 state 11 - D3HOT state 472 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.2.19 MID - Message Signaled Interrupt Identifiers B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 8C-8Dh 0005h RO 16 bits Bit Access Default Value 15:8 RO 00h Description Next Pointer (NEXT): Indicates the next item in the list. This can be other capability pointers (such as PCI-X or PCI-Express) or it can be the last item in the list. 7:0 RO 05h Capability ID (CID): Capabilities ID indicates MSI. 22.2.20 MC - Message Signaled Interrupt Message Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 8E-8Fh 0080h RO; RW 16 bits Bit Access Default Value 15:8 RO 00h 7 RO 1b Description Reserved 64-Bit Address Capable (C64): Specifies whether capable of generating 64-bit messages. 6:4 RO 000b Multiple Message Enable (MME): Not implemented, hardwired to 0. 3:1 RO 000b Multiple Message Capable (MMC): Not implemented, hardwired to 0. 0 RW 0b MSI Enable (MSIE): I f set, MSI is enabled and traditional interrupt pins are not used to generate interrupts. Datasheet 473 Intel(R) Management Engine Subsystem PCI Device 3 22.2.21 MA - Message Signaled Interrupt Message Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 90-93h 00000000h RO; RW; 32 bits Bit Access Default Value 31:2 RW 00000000h Description Address (ADDR): Lower 32 bits of the system specified message address, always DW aligned. 1:0 22.2.22 RO 00b Reserved MD - Message Signaled Interrupt Message Data B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/1/PCI 98-99h 0000h RW 16 bits Bit Access Default Value 15:0 RW 0000h Description Data (Data): This 16-bit field is programmed by system software if MSI is enabled. Its content is driven onto the FSB during the data phase of the MSI memory write transaction. 474 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.2.23 HIDM - MEI Interrupt Delivery Mode B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/3/1/PCI A0h 00h RW 8 bits 00h Bit Access Default Value 7:2 RO 0h 1:0 RW 00b Description Reserved MEI Interrupt Delivery Mode (HIDM): These bits control what type of interrupt the Intel(R) MEI will send when ARC writes to set the M_IG bit in AUX space. They are interpreted as follows: 00: Generate Legacy or MSI interrupt 01: Generate SCI 10: Generate SMI 22.3 AMT IDER PCI Device 3 Function 2 Register Name Identification Register Symbol ID Register Start 0 Register End 3 Default Value 2A06h1 Access RO 2A16h2 Command Register CMD 4 5 0000b RO;RW Device Status STS 6 7 00B0h RO Revision ID RID 8 8 00h RO Class Codes CC 9 B 010185h RO Cache Line Size CLS C C 00h RO Master Latency Timer MLT D D 00h RO Header Type HTYPE E E < Not Defined > < Not Defined > F F Reserved Primary Command Block IO Bar PCMDBA 10 13 00000001h RO; RW Primary Control Block Base Address PCTLBA 14 17 00000001h RO; RW Datasheet 475 Intel(R) Management Engine Subsystem PCI Device 3 Register Name Register Symbol Register End Default Value Access Secondary Command Block Base Address SCMDBA 18 1B 00000001h RO; RW Secondary Control Block base Address SCTLBA 1C 1F 00000001h RO; RW Legacy Bus Master Base Address LBAR 20 23 00000001h RO; RW Reserved RSVD 24 27 28 2B Reserved Sub System Identifiers SS 2C 2F 00008086h RWO Expansion ROM Base Address EROM 30 33 00000000h RO Capabilities Pointer CAP 34 34 C8h RO 35 3B Reserved Interrupt Information INTR 3C 3D 0300h RO; RW Minimum Grant MGNT 3E 3E 00h RO Maximum Latency MLAT 3F 3F 00h RO 40 C7 Reserved 476 Register Start PCI Power Management Capability ID PID C8 C9 D001h RO PCI Power Management Capabilities PC CA CB 0023h RO PCI Power Management Control and Status PMCS CC CF 00000000h RO; RW; RWC Message Signaled Interrupt Capability ID MID D0 D1 0005h RO Datasheet Intel(R) Management Engine Subsystem PCI Device 3 Register Name Register Symbol Register Start Register End Default Value Access Message Signaled Interrupt Message Control MC D2 D3 0080h RO; RW Message Signaled Interrupt Message Address MA D4 D7 00000000h RO; RW Message Signaled Interrupt Message Upper Address MAU D8 DB 00000000h RO; RW Message Signaled Interrupt Message Data MD DC DD 0000h RW NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only 22.3.1 ID - Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 0-3h 29768086h RO 32 bits Bit Access Default Value 31:16 RO 2A06h1 2 2A16h 15:0 RO 8086h Description Device ID (DID): Assigned by Manufacturer, identifies the type of Device. Vendor ID (VID): 16-bit field which indicates the company vendor as Intel NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only Datasheet 477 Intel(R) Management Engine Subsystem PCI Device 3 22.3.2 CMD - Command Register B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 4-5h 0000h RO; RW 16 bits . Bit Access Default Value 15:11 RO 00h 10 RW 0b Description Reserved Interrupt Disable (ID): This disables pin-based INTx# interrupts. This bit has no effect on MSI operation. When set, internal INTx# messages will not be generated. When cleared, internal INTx# messages are generated if there is an interrupt and MSI is not enabled. 9:3 RO 0b Reserved 2 RW 0b Bus Master Enable (BME): Controls the Intel(R) Active Management Technology (Intel(R) AMT) function's ability to act as a master for data transfers. This bit does not impact the generation of completions for split transaction commands. 1 RO 0b Memory Space Enable (MSE): Intel AMT function does not contain target memory space. 0 RW 0b I/O Space Enable (IOSE): Controls access to the Intel AMT function's target I/O space. 478 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.3.3 STS - Device Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 6-7h 00B0h RO 16 bits Bit Access Default Value 15 RO 0b Description Detected Parity Error (DPE): No parity error on its interface. 14 RO 0b Signaled System Error (SSE): The Intel(R) AMT function will never generate a SERR#. 13 RO 0b Reserved 12 RO 0b Reserved 11 RO 0b Reserved 10:9 RO 00b DEVSEL# Timing Status (DEVT): Controls the device select time for the Intel AMT function's PCI interface. 8 RO 0b Master Data Parity Error Detected) (DPD): Intel AMT function (IDER), as a master, does not detect a parity error. Other Intel AMT function is not a master and hence this bit is reserved also. 7:5 RO 1b 4 RO 1b Reserved Capabilities List (CL): Indicates that there is a capabilities pointer implemented in the device. 3 RO 0b Interrupt Status (IS): This bit reflects the state of the interrupt in the function. Setting of the Interrupt Disable bit to 1 has no affect on this bit. Only when this bit is a 1 and ID bit is 0 is the INTC interrupt asserted to the Host 2:0 Datasheet RO 000b Reserved 479 Intel(R) Management Engine Subsystem PCI Device 3 22.3.4 RID - Revision ID B/D/F/Type: Address Offset: Default Value: Access: Size: 22.3.5 0/3/2/PCI 8h 00h RO 8 bits Bit Access Default Value Description 7:0 RO 00h Revision ID (RID): This is an 8-bit value that indicates the revision identification number for the (G)MCH. A register swapping mechanism behind RID register is used to select between a single SRID, or a single CRID to be reflected in the RID register. For the C0 stepping SRID= 03h, CRID= 0Ch. CC - Class Codes B/D/F/Type: Address Offset: Default Value: Access: Size: 22.3.6 0/3/2/PCI 9-Bh 010185h RO 24 bits Bit Access Default Value 23:0 RO 010185h Description Programming Interface BCC SCC (PI BCC SCC) CLS - Cache Line Size B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI Ch 00h RO 8 bits . Bit Access Default Value 7:0 RO 00h Description Cache Line Size (CLS): All writes to system memory are Memory Writes. 480 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.3.7 MLT - Master Latency Timer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI Dh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Master Latency Timer (MLT): Not implemented since the function is in (G)MCH 22.3.8 HTYPE - Header Type B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI Eh < Not Defined > < Not Defined > 8 bits Register is not implemented. 22.3.9 PCMDBA - Primary Command Block IO Bar B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 10-13h 00000001h RO; RW 32 bits Bit Access Default Value Description 31:16 RO 0000h Reserved 15:3 RW 0000h Base Address (BAR): Base Address of the BAR0 I/O space (8 consecutive I/O locations) 2:1 RO 00b 0 RO 1b Reserved Resource Type Indicator (RTE): Indicates a request for I/O space Datasheet 481 Intel(R) Management Engine Subsystem PCI Device 3 22.3.10 PCTLBA - Primary Control Block Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 14-17h 00000001h RO; RW 32 bits Bit Access Default Value Description 31:16 RO 0000h Reserved 15:2 RW 0000h Base Address (BAR): Base Address of the BAR1 I/O space (4 consecutive I/O locations) 1 RO 0b Reserved 0 RO 1b Resource Type Indicator (RTE): Indicates a request for I/O space 22.3.11 SCMDBA - Secondary Command Block Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 18-1Bh 00000001h RO; RW 32 bits Bit Access Default Value Description 31:16 RO 0000h Reserved 15:3 RW 0000h Base Address (BAR): Base Address of the I/O space (8 consecutive I/O locations) 2:1 RO 00b 0 RO 1b Reserved Resource Type Indicator (RTE): Indicates a request for I/O space 482 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.3.12 SCTLBA - Secondary Control Block Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 1C-1Fh 00000001h RO; RW 32 bits Bit Access Default Value Description 31:16 RO 0000h Reserved 15:2 RW 0000h Base Address (BAR): Base Address of the I/O space (4 consecutive I/O locations) 1 RO 0b Reserved 0 RO 1b Resource Type Indicator (RTE): Indicates a request for I/O space 22.3.13 LBAR - Legacy Bus Master Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 20-23h 00000001h RO; RW 32 bits Bit Access Default Value 31:16 RO 0000h 15:4 RW 000h Description Reserved Base Address (BA): Base Address of the I/O space (16 consecutive I/O locations) 3:1 RO 000b 0 RO 1b Reserved Resource Type Indicator (RTE): Indicates a request for I/O space Datasheet 483 Intel(R) Management Engine Subsystem PCI Device 3 22.3.14 SS - Sub System Identifiers B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 2C-2Fh 00008086h RWO 32 bits Bit Access Default Value 31:16 RWO 0000h Description Subsystem ID (SSID): This is written by BIOS. No hardware action taken on this value 15:0 RWO 8086h Subsystem Vendor ID (SSVID): This is written by BIOS. No hardware action taken on this value 22.3.15 EROM - Expansion ROM Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 30-33h 00000000h RO 32 bits Bit Access Default Value 31:11 RO 000000h 10:1 RO 000h 0 RO 0b Description Expansion ROM Base Address (ERBAR) Reserved Enable (EN): Enable expansion ROM Access 22.3.16 CAP - Capabilities Pointer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 34h C8h RO 8 bits Bit Access Default Value 7:0 RO c8h Description Capability Pointer (CP): Indicates that the first capability pointer offset is offset c8h (the power management capability) 484 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.3.17 INTR - Interrupt Information B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI 3C-3Dh 0300h RO; RW 16 bits Bit Access Default Value 15:8 RO 03h Description Interrupt Pin (IPIN): A value of 0x1/0x2/0x3/0x4 indicates that this function implements legacy interrupt on INTA/INTB/INTC/INTD, respectively Function ( 2 IDE) 7:0 RW 00h Value INTx 03h INTC Interrupt Line (ILINE): The value written in this register tells which input of the system interrupt controller, the device's interrupt pin is connected to. This value is used by the OS and the device driver, and has no affect on the HW 22.3.18 MGNT - Minimum Grant B/D/F/Type: Address Offset: Default Value: Access: Size: Datasheet 0/3/2/PCI 3Eh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Reserved 485 Intel(R) Management Engine Subsystem PCI Device 3 22.3.19 MLAT - Maximum Latency B/D/F/Type: Address Offset: Default Value: Access: Size: 22.3.20 0/3/2/PCI 3Fh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Reserved PID - PCI Power Management Capability ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI C8-C9h D001h RO 16 bits Bit Access Default Value 15:8 RO D0h Description Next Capability (NEXT): Its value of 0xD0 points to the MSI capability 7:0 RO 01h Cap ID (CID): Indicates that this pointer is a PCI power management 486 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.3.21 PC - PCI Power Management Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI CA-CBh 0023h RO 16 bits Bit Access Default Value 15:11 RO 00000b Description PME Support (PME): Indicates no PME# in the Intel(R) AMT function 10 RO 0b D2 Support (D2S): The D2 state is not Supported 9 RO 0b D1 Support (D1S): The D1 state is not supported 8:6 RO 000b 5 RO 1b Reserved Device Specific Initialization (DSI): Indicates that no device-specific initialization is required. 4 RO 0b Reserved 3 RO 0b PME Clock (PMEC): Indicates that PCI clock is not required to generate PME# 2:0 RO 011b Version (VS): Indicates support for revision 1.2 of the PCI power management specification Datasheet 487 Intel(R) Management Engine Subsystem PCI Device 3 22.3.22 PMCS - PCI Power Management Control and Status B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/3/2/PCI CC-CFh 00000000h RO; RW; RWC 32 bits 0000h Bit Access Default Value Description 31:16 RO 0h Reserved 15 RO 0b PME Status (PMES): This bit is set when a PME event is to be requested. Not supported 14:9 RO 00h 8 RO 0b Reserved PME Enable (PMEE): Not Supported 7:4 RO 0000b 3 RWC 0b Reserved No Soft Reset (NSR): When set (1), this bit indicates that devices transitioning from D3hot to D0 because of PowerState commands do not perform an internal reset. Configuration Context is preserved. Upon transition from the D3hot to the D0 Initialized state, no additional operating system intervention is required to preserve Configuration Context beyond writing the PowerState bits. When clear (0), devices do perform an internal reset upon transitioning from D3hot to D0 via software control of the PowerState bits. Configuration Context is lost when performing the soft reset. Upon transition from the D3hot to the D0 state, full reinitialization sequence is needed to return the device to D0 Initialized. 2 RO 0b 1:0 RW 00b Reserved Power State (PS): This field is used both to determine the current power state of the Intel(R) AMT function and to set a new power state. The values are: 00 - D0 state 11 - D3HOT state 488 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.3.23 MID - Message Signaled Interrupt Capability ID B/D/F/Type: Address Offset: Default Value: Access: Size: Bit 15:8 Access RO 0/3/2/PCI D0-D1h 0005h RO 16 bits Default Value 00h Description Next Pointer (NEXT): Value indicates this is the last item in the capabilities list. 7:0 RO 05h Capability ID (CID): Capabilities ID value indicates device is capable of generating an MSI 22.3.24 MC - Message Signaled Interrupt Message Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI D2-D3h 0080h RO; RW 16 bits . Bit Access Default Value 15:8 RO 00h 7 RO 1b Description Reserved 64-Bit Address Capable (C64): Capable of generating 64-bit and 32-bit messages 6:4 RW 000b Multiple Message Enable (MME): These bits are R/W for software compatibility, but only one message is ever sent by the Intel(R) AMT function 3:1 RO 000b Multiple Message Capable (MMC): Only one message is required 0 RW 0b MSI Enable (MSIE): If set, MSI is enabled and traditional interrupt pins are not used to generate interrupts Datasheet 489 Intel(R) Management Engine Subsystem PCI Device 3 22.3.25 MA - Message Signaled Interrupt Message Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI D4-D7h 00000000h RO; RW 32 bits Bit Access Default Value 31:2 RW 00000000h Description Address (ADDR): Lower 32 bits of the system specified message address, always Dword aligned 1:0 22.3.26 RO 00b Reserved MAU - Message Signaled Interrupt Message Upper Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI D8-DBh 00000000h RO; RW 32 bits Bit Access Default Value 31:4 RO 0000000h 3:0 RW 0000b Description Reserved Address (ADDR): Upper 4 bits of the system specified message address 22.3.27 MD - Message Signaled Interrupt Message Data B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/2/PCI DC-DDh 0000h RW 16 bits Bit Access Default Value 15:0 RW 0000h Description Data (DATA): This content is driven onto the lower word of the data bus of the MSI memory write transaction 490 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.4 (KT) Redirection PCI Device 3 Function 3 Register Name Identification Register Symbol ID Register Start 0 Register End 3 Default Value 2A07h1 Access RO 2A17h2 Command Register CMD 4 5 0000h RO; RW Device Status STS 6 7 00B0h RO Revision ID RID 8 8 00h RO Class Codes CC 9 B 010185h RO Cache Line Size CLS C C 00h RO Master Latency Timer MLT D D 00h RO Header Type HTYPE E E < Not Defined > < Not Defined > F F Reserved KT IO Block Base Address KTIBA 10 13 00000001h RO; RW KT Mem Block Base Address KTMBA 14 17 00000000h RO; RW 18 28 Reserved Sub System Identifiers SS 2C 2F 00008086h RWO Expansion ROM Base Address EROM 30 33 00000000h RO Capabilities Pointer CAP 34 34 C8h RO 35 3B Reserved Interrupt Information INTR 3C 3D 0200h RO; RW Minimum Grant MGNT 3E 3E 00h RO Maximum Latency MLAT 3F 3F 00h RO 40 C7 C8 C9 D001h RO Reserved PCI Power Management Capability ID Datasheet PID 491 Intel(R) Management Engine Subsystem PCI Device 3 Register Name Register Symbol Register Start Register End Default Value Access PCI Power Management Capabilities PC CA CB 0023h RO PCI Power Management Control and Status PMCS CC CF 00000000h RO; RW; RWC Message Signaled Interrupt Capability ID MID D0 D1 0005h RO Message Signaled Interrupt Message Control MC D2 D3 0080h RO; RW Message Signaled Interrupt Message Address MA D4 D7 00000000h RO; RW Message Signaled Interrupt Message Upper Address MAU D8 DB 00000000h RO; RW Message Signaled Interrupt Message Data MD DC DD 0000h RW NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only 492 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.4.1 ID - Identification B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI 0-3h 29878086h RO 32 bits Bit Access Default Value 31:16 RO 2A07h1 Device ID (DID): 2A17h2 Assigned by manufacturer, identifies the device. 15:0 RO 8086h Description Vendor ID (VID): 16-bit field which indicates the company vendor as Intel. NOTES: 1. Valid for all Mobile Intel 965 Express Chipsets except for the Mobile Intel GME965 and GLE960 Express Chipsets. 2. Valid for the Mobile Intel GME965 and GLE960 Express Chipsets only. 22.4.2 CMD - Command Register B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI 4-5h 0000h RO; RW 16 bits Bit Access Default Value 15:11 RO 00h 10 RW 0b Description Reserved Interrupt Disable (ID): This disables pin-based INTx# interrupts. This bit has no effect on MSI operation. When set, internal INTx# messages will not be generated. When cleared, internal INTx# messages are generated if there is an interrupt and MSI is not enabled. 9:3 RO 0b Fast Back-to-Back Enable (FBE): Reserved 2 RW 0b Bus Master Enable (BME): Controls the KT function's ability to act as a master for data transfers. This bit does not impact the generation of completions for split transaction commands. For KT, the only bus mastering activity is MSI generation. 1 RW 0b Memory Space Enable (MSE): Controls Access to the Intel(R) AMT function's target memory space. 0 RW 0b I/O Space Enable (IOSE): Controls access to the Intel AMT function's target I/O space. Datasheet 493 Intel(R) Management Engine Subsystem PCI Device 3 22.4.3 STS - Device Status B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI 6-7h 00B0h RO 16 bits Bit Access Default Value 15 RO 0b Description Detected Parity Error (DPE): No parity error on its interface 14 RO 0b Signaled System Error (SSE): The Intel(R) AMT function will never generate an SERR# 13 RO 0b Reserved 12 RO 0b Reserved 11 RO 0b Reserved 10:9 RO 00b DEVSEL# Timing Status (DEVT): Controls the device select time for the Intel AMT function's PCI interface 8 RO 0b Master Data Parity Error Detected) (DPD): AMT function (IDER), as a master, does not detect a parity error. Other AMT function is not a master and hence this bit is reserved also. 7 RO 1b Reserved 6 RO 0b Reserved 5 RO 1b Reserved 4 RO 1b Capabilities List (CL): Indicates that there is a capabilities pointer implemented in the device. 3 RO 0b Interrupt Status (IS): This bit reflects the state of the interrupt in the function. Setting of the Interrupt Disable bit to 1 has no affect on this bit. Only when this bit is a 1 and ID bit is 0 is the INTB interrupt asserted to the Host 2:0 494 RO 000b Reserved Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.4.4 RID - Revision ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI 8h 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Revision ID (RID): This is an 8-bit value that indicates the revision identification number for the (G)MCH. A register swapping mechanism behind RID register is used to select between a single SRID, or a single CRID to be reflected in the RID register. For the C0 stepping SRID= 03h, CRID= 0Ch. 22.4.5 CC - Class Codes B/D/F/Type: Address Offset: Default Value: Access: Size: 22.4.6 0/3/3/PCI 9-Bh 010185h RO 24 bits Bit Access Default Value 23:0 RO 010185h Description Programming Interface BCC SCC (PI BCC SCC) CLS - Cache Line Size B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI Ch 00h RO; 8 bits Bit Access Default Value 7:0 RO 00h Description Cache Line Size (CLS): All writes to system memory are Memory Writes. Datasheet 495 Intel(R) Management Engine Subsystem PCI Device 3 22.4.7 MLT - Master Latency Timer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI Dh 00h RO 8 bits . Bit Access Default Value 7:0 RO 00h Description Master Latency Timer (MLT): Not implemented since the function is in (G)MCH. 22.4.8 HTYPE - Header Type B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI Eh < Not Defined > < Not Defined > 8 bits Register is not implemented. Reads return 0. 22.4.9 KTIBA - KT IO Block Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI 10-13h 00000001h RO; RW 32 bits Bit Access Default Value Description 31:16 RO 0000h Reserved 15:3 RW 0000h Base Address (BAR): Base Address of the I/O space (8 consecutive I/O locations). 2:1 RO 00b 0 RO 1b Reserved Resource Type Indicator (RTE): Indicates a request for I/O space. 496 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.4.10 KTMBA - KT Mem Block Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 22.4.11 0/3/3/PCI 14-17h 00000000h RO; RW 32 bits Bit Access Default Value 31:12 RW 00000h 11:4 RO 00h 3 RO 0b 2:1 RO 00b 0 RO 0b Base Address (BAR): Memory Mapped IO BAR. Reserved Prefetchable (PF): Indicates that this range is not prefetchable. Type (TP): Indicates that this range can be mapped anywhere in 32-bit address space. Resource Type Indicator (RTE): Indicates a request for register memory space. SS - Sub System Identifiers B/D/F/Type: Address Offset: Default Value: Access: Size: Datasheet Description 0/3/3/PCI 2C-2Fh 00008086h RWO 32 bits Bit Access Default Value Description 31:16 RWO 0000h Subsystem ID (SSID): This is written by BIOS. No hardware action taken on this value. 15:0 RWO 8086h Subsystem Vendor ID (SSVID): This is written by BIOS. No hardware action taken on this value. 497 Intel(R) Management Engine Subsystem PCI Device 3 22.4.12 EROM - Expansion ROM Base Address B/D/F/Type: Address Offset: Default Value: Access: Size: 22.4.13 0/3/3/PCI 30-33h 00000000h RO 32 bits Bit Access Default Value 31:11 RO 000000h 10:1 RO 000h 0 RO 0b Description Expansion ROM Base Address (ERBAR) Reserved Enable (EN): Enable expansion ROM Access. CAP - Capabilities Pointer B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI 34h C8h RO 8 bits . 498 Bit Access Default Value 7:0 RO c8h Description Capability Pointer (CP): Indicates that the first capability pointer offset is offset c8h ( the power management capability) Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.4.14 INTR - Interrupt Information B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI 3C-3Dh 0200h RW; RO 16 bits Bit Access Default Value 15:8 RO 02h Description Interrupt Pin (IPIN): A value of 0x1/0x2/0x3/0x4 indicates that this function implements legacy interrupt on INTA/INTB/INTC/INTD, respectively. Function ( 3 KT/Serial Port) 7:0 22.4.15 RW 00h Interrupt Line (ILINE): The value written in this register tells which input of the system interrupt controller, the device's interrupt pin is connected to. This value is used by the OS and the device driver, and has no affect on the hardware. 0/3/3/PCI 3Eh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Reserved MLAT - Maximum Latency B/D/F/Type: Address Offset: Default Value: Access: Size: Datasheet INTx INTB MGNT - Minimum Grant B/D/F/Type: Address Offset: Default Value: Access: Size: 22.4.16 Value 02h 0/3/3/PCI 3Fh 00h RO 8 bits Bit Access Default Value 7:0 RO 00h Description Reserved 499 Intel(R) Management Engine Subsystem PCI Device 3 22.4.17 PID - PCI Power Management Capability ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI C8-C9h D001h RO 16 bits it Access Default Value 15:8 RO D0h Description Next Capability (NEXT): Its value of 0xD0 points to the MSI capability. 7:0 RO 01h Cap ID (CID): Indicates that this pointer is a PCI power management. 22.4.18 PC - PCI Power Management Capabilities B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI CA-CBh 0023h RO 16 bits Bit Access Default Value 15:11 RO 00000b Description PME Support (PME): Indicates no PME# in the Intel(R) AMT function. 10 RO 0b D2 Support (D2S): The D2 state is not supported. 9 RO 0b D1 Support (D1S): The D1 state is not supported. 8:6 RO 000b Aux Current (AUXC): PME# from D3 (cold) state is not supported, therefore this field is 000b. 5 RO 1b Device Specific Initialization (DSI): Indicates that no device-specific initialization is required. 4 RO 0b Reserved 3 RO 0b PME Clock (PMEC): Indicates that PCI clock is not required to generate PME#. 2:0 RO 011b Version (VS): Indicates support for revision 1.2 of the PCI power management specification. 500 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.4.19 PMCS - PCI Power Management Control and Status B/D/F/Type: Address Offset: Default Value: Access: Size: BIOS Optimal Default 0/3/3/PCI CC-CFh 00000000h RO; RW; RWC 32 bits 0000h Bit Access Default Value Description 31:16 RO 0h Reserved 15 RO 0b PME Status (PMES): This bit is set when a PME event is to be requested. Not supported. 14:9 RO 00h 8 RO 0b Reserved PME Enable (PMEE): Not Supported. 7:4 RO 0h Reserved 3 RWC 0b No Soft Reset (NSR): When set (1), this bit indicates that devices transitioning from D3hot to D0 because of PowerState commands do not perform an internal reset. Configuration Context is preserved. Upon transition from the D3hot to the D0 Initialized state, no additional operating system intervention is required to preserve Configuration Context beyond writing the PowerState bits. When clear (0), devices do perform an internal reset upon transitioning from D3hot to D0 via software control of the PowerState bits. Configuration Context is lost when performing the soft reset. Upon transition from the D3hot to the D0 state, full reinitialization sequence is needed to return the device to D0 Initialized. 2 RO 0b 1:0 RW 00b Reserved Power State (PS): This field is used both to determine the current power state of the Intel(R) AMT function and to set a new power state. The values are: 00 - D0 state 11 - D3HOT state When in the D3HOT state, the controller's configuration space is available, but the I/O and memory spaces are not. Additionally, interrupts are blocked. If software attempts to write a `10' or '01' to these bits, the write will be ignored. Datasheet 501 Intel(R) Management Engine Subsystem PCI Device 3 22.4.20 MID - Message Signaled Interrupt Capability ID B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI D0-D1h 0005h RO 16 bits Bit Access Default Value 15:8 RO 00h Description Next Pointer (NEXT): Value Indicates this is the last item in the list. 7:0 RO 05h Capability ID (CID): Value of Capabilities ID indicates device is capable of generating MSI. 22.4.21 MC - Message Signaled Interrupt Message Control B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI D2-D3h 0080h RO; RW 16 bits Bit Access Default Value 15:8 RO 00h 7 RO 1b Description Reserved 64-Bit Address Capable (C64): Capable of generating 64-bit and 32-bit messages. 6:4 RW 000b Multiple Message Enable (MME): These bits are R/W for software compatibility, but only one message is ever sent by the Intel(R) AMT function. 3:1 RO 000b Multiple Message Capable (MMC): Only one message is required. 0 RW 0b MSI Enable (MSIE): If set MSI is enabled and traditional interrupt pins are not used to generate interrupts. 502 Datasheet Intel(R) Management Engine Subsystem PCI Device 3 22.4.22 MA - Message Signaled Interrupt Message Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI D4-D7h 00000000h RO; RW 32 bits Bit Access Default Value 31:2 RW 00000000h Description Address (ADDR): Lower 32 bits of the system specified message address, always Dworded. 1:0 22.4.23 RO 00b Reserved MAU - Message Signaled Interrupt Message Upper Address B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI D8-DBh 00000000h RO; RW 32 bits Bit Access Default Value 31:4 RO 0000000h 3:0 RW 0000b Description Reserved Address (ADDR): Upper 4 bits of the system specified message address. 22.4.24 MD - Message Signaled Interrupt Message Data B/D/F/Type: Address Offset: Default Value: Access: Size: 0/3/3/PCI DC-DDh 0000h RW 16 bits Bit Access Default Value 15:0 RW 0000h Description Data (DATA): This MSI data is driven onto the lower word of the data bus of the MSI memory write transaction. Datasheet 503