BT169D,116 - NXP SEMICONDUCTORS

1. Product profile

1.1 General description

Passivated, sensitive gate thyristors in a SOT54 plastic package.

1.2 Features and benefits

Designed to be interfaced directly to microcontrollers, logic integrated circuits and

other low power gate trigger circuits.

1.3 Applications

General purpose switching and phase control applications.

1.4 Quick reference data

2. Pinning information

BT169 series

Thyristors logic level

Rev. 5 — 30 September 2011 Product data sheet

TO-92

VDRM, VRRM  200 V (BT169B) IT(RMS)  0.8 A

VDRM, VRRM  400 V (BT169D) IT(AV)  0.5 A

VDRM, VRRM  600 V (BT169G) ITSM  8 A

Table 1. Discrete pinning

Pin Description Simplified outline Symbol

1 anode (a)

SOT54 (T O-92)

2 gate (g)

3 cathode (k)

123

sym037

Product data sheet Rev. 5 — 30 September 2011 2 of 13

NXP Semiconductors BT169 series

Thyristor logic level

3. Ordering information

4. Limiting values

[1] Although not recommended, off-state voltages up to 800 V may be applied without damage, but the thyristor may switch to the on-state.

The rate of rise of current should not exceed 15 A/s.

Table 2. Ordering informatio n

Type number Package

Name Description Version

BT169B - plastic single-ended leaded (through hole) package; 3 leads SOT54

BT169D

BT169G

Table 3. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol Parameter Conditions Min Max Unit

VDRM, VRRM repetitive peak off-state voltages

BT169B [1] -200V

BT169D [1] -400V

BT169G [1] -600V

IT(AV) average on-state current half sine wave;

Tlead 83 C;

see Figure 1

-0.5A

IT(RMS) RMS on-state current all conduction angles;

see Figure 4 and 5-0.8A

ITSM non-repetitive peak on-state current half sine wave;

Tj=25C prior to

surge;

see Figure 2 and 3

t = 10 ms - 8 A

t = 8.3 ms - 9 A

I2tI

2t for fusing t = 10 ms - 0.32 A2s

dIT/dt repetitive rate of rise of on-state

current after triggering ITM = 2 A; IG = 10 mA;

dIG/dt = 100 mA/s-50A/s

IGM peak gate current - 1 A

VGM peak gate voltage - 5 V

VRGM peak reverse gate voltage - 5 V

PGM peak gate pow e r - 2 W

PG(AV) averag e gate power over any 20 ms period - 0.1 W

Tstg storage temperature 40 +150 C

Tjjunction temperature - 125 C

Product data sheet Rev. 5 — 30 September 2011 3 of 13

NXP Semiconductors BT169 series

Thyristor logic level

a = form factor = IT(RMS)/IT(AV).

Fig 1. Total power dissipation as a function of average on-st ate current; maximum values.

f = 50 Hz.

Fig 2. No n-re pe titive peak on-state current as a function of the number of sinusoidal current cycles; maximum

values.

001aab446

0.4

0.2

0.6

0.8

Ptot

(W)

101

113

125

IT(AV) (A)

0 0.60.40.20.1 0.50.3

a =

1.57

2.2

1.9

2.8

conduction

angle

(degrees)

form

factor

120

180

2.8

2.2

1.9

1.57

Tlead(max)

(°C)

001aab499

ITSM

(A)

number of cycles

1 103

102

Tj(init) = 25 °C max

ITITSM

Product data sheet Rev. 5 — 30 September 2011 4 of 13

NXP Semiconductors BT169 series

Thyristor logic level

tp  10 ms.

Fig 3. Non-repetitive peak on-state current as a function of pulse width for sinusoidal current s; maximum

values.

f = 50 Hz; Tlead  83 C. (1) Tlead = 83 C.

Fig 4. RMS on-state current as a function of surge

duration for sinusoidal currents. Fig 5. RMS on-state current as a function of lead

temperature; maximum values.

001aab497

tp (s)

10−510−2

10−3

10−4

102

103

ITSM

(A)

Tj(init) = 25 °C max

ITITSM

001aab449

0.5

1.5

IT(RMS)

(A)

surge duration (s)

10−210−1101

Tlead (°C)

−50 150100050

001aab450

0.4

0.6

0.2

0.8

IT(RMS)

(A)

(1)

Product data sheet Rev. 5 — 30 September 2011 5 of 13

NXP Semiconductors BT169 series

Thyristor logic level

5. Thermal characteristics

Table 4. Thermal characteristics

Symbol Parameter Conditions Min Typ Max Unit

Rth(j-lead) thermal resist an ce from juncti on to

lead --60K/W

Rth(j-a) thermal resista nce from junc tion to

ambient printed-circuit board mounted;

lead length = 4 mm -150-K/W

Fig 6. Transient thermal impedance as a func tio n of pu ls e width .

001aab451

102

10−1

Zth(j-lead)

(K/W)

10−2

tp (s)

10−511010−1

10−2

10−410−3

δ =

Product data sheet Rev. 5 — 30 September 2011 6 of 13

NXP Semiconductors BT169 series

Thyristor logic level

6. Characteristics

Table 5. Characteristics

Tj = 25



C unless otherwise stated.

Symbol Parameter Conditions Min Typ Max Unit

Static characteristics

IGT gate trigger current VD = 12 V; IT = 10 mA;

gate open circuit; see Figure 8 -50200A

ILlatching current VD = 12 V; IGT = 0.5 mA;

RGK =1k; see Figure 10 - 26mA

IHholding current VD = 12 V; IGT = 0.5 mA;

RGK =1k; see Figure 11 - 25mA

VTon-state voltage IT = 1.2 A - 1.25 1.7 V

VGT gate trigger voltage IT = 10 mA; gate open circuit;

see Figure 7

VD = 12 V - 0.5 0.8 V

VD = VDRM(max); Tj = 125 C0.20.3-V

ID, IRoff-state leakage

current VD = VDRM(max); VR = VRRM(max);

Tj= 125 C; RGK = 1 k

- 0.05 0.1 mA

Dynamic characteristics

dVD/dt critical rate of rise of

off-state voltage VDM = 67 % VDRM(max); Tj = 125 C;

exponential waveform;

see Figure 12

RGK = 1 k500 800 - V/s

gate open circuit - 25 - V/s

tgt gate controll ed

turn-on time ITM = 2 A; VD = VDRM(max);

IG=10mA; dI

G/dt = 0.1 A/s-2-s

tqcircuit commuted

turn-off time VD = 67 % VDRM(max); Tj = 125 C;

ITM = 1.6 A; VR = 35 V;

dITM/dt = 30 A/s; dVD/dt = 2 V/s;

RGK = 1 k

-100-s

Product data sheet Rev. 5 — 30 September 2011 7 of 13

NXP Semiconductors BT169 series

Thyristor logic level

Fig 7. Normalized gate trigger voltage as a function of

junction temperature. Fig 8. Normalized gate trigger current as a function

junction temperature.

VO = 1.067 V.

RS = 0.187 .

(1) Tj = 125 C; typical values.

(2) Tj = 125 C; maximum values.

(3) Tj = 25 C; maximum values.

RGK = 1 k.

Fig 9. On-state current characteristics. Fig 10. Normalized latching current as a function of

junction temperature.

Tj (°C)

−50 150100050

001aab501

0.8

1.2

1.6

0.4

VGT

VGT(25°C)

Tj (°C)

−50 150100050

001aab502

IGT

IGT(25°C)

001aab454

VT (V)

0.4 2.821.2

(A)

(1) (2) (3)

Tj (°C)

−50 150100050

001aab503

IL(25°C)

Product data sheet Rev. 5 — 30 September 2011 8 of 13

NXP Semiconductors BT169 series

Thyristor logic level

7. Package information

Epoxy meets requirements of UL94 V-0 at 1⁄8 inch.

RGK = 1 k.(1)R

GK = 1 k.

(2) Gate open circuit.

Fig 11. Normalized holding current as a function of

junction temperature. Fig 12. Critical rate of rise of off-state voltage as a

function of junction temperature; typical

values.

Tj (°C)

−50 150100050

001aab504

IH(25°C)

001aab507

Tj (°C)

0 15010050

103

102

104

dVD/dt

(V/μs)

(1)

(2)

Product data sheet Rev. 5 — 30 September 2011 9 of 13

NXP Semiconductors BT169 series

Thyristor logic level

8. Package outline

Fig 13. Package outline SOT54 (TO-92).

UNIT A

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 5.2

5.0

0.48

0.40

0.45

0.38

4.8

4.4

1.7

1.4

4.2

3.6

14.5

12.7

2.54

1.27

(1)

max.

2.5

0.66

0.55

DIMENSIONS (mm are the original dimensions)

Note

1. Terminal dimensions within this zone are uncontrolled to allow for flow of plastic and terminal irregularities.

SOT54 TO-92 SC-43A 04-06-28

04-11-16

A L

0 2.5 5 mm

scale

b1L1

Plastic single-ended leaded (through hole) package; 3 leads SOT54

e1e

Product data sheet Rev. 5 — 30 September 2011 10 of 13

NXP Semiconductors BT169 series

Thyristor logic level

9. Revision history

Table 6. Revision history

Document ID Release date Data sheet status Change notice Or de r nu mber Supersedes

BT169_SERIES v.5 20110930 Product data sheet - 9397 750 13512 BT169_SERIES v.4

Modifications: •The format of this data sheet has been redesigned to comply with the new identity

guidelines of NXP Semiconductors.

•Legal texts have been adapted to the new company name where appropriate.

BT169_SERIES v.4 20040823 Product data sheet - 9397 750 13512 BT169_SERIES v.3

Modifications: •The format of this data sheet has been redesigned to comply with the new presentation and

information standard of Philips Semiconductors.

•Section 1.4 “Quick reference data”: BT169E obsolete, removed from list.

•Table 2 “Ordering information”: BT169E obsolete, removed from table.

•Table 3 “Limiting values”: BT169E obsolete, removed from table.

BT169_SERIES v.3 20010902 Product specification - not applicable BT169_SERIES v.2

BT169_SERIES v.2 20010901 Product specification - not applicable BT169_SERIES v.1

BT169_SERIES v.1 19970901 Product specification - not applicable -

Product data sheet Rev. 5 — 30 September 2011 11 of 13

NXP Semiconductors BT169 series

Thyristor logic level

10. Legal information

10.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Definitions”.

[3] The product status of de vice(s) descr ibed in th is docume nt may have cha nged since this docume nt was publis hed and ma y dif fer in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nxp.com.

10.2 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liab ility for the consequences of

use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and tit le. A short data sh eet is intended

for quick reference only and shou ld not be rel ied u pon to cont ain det ailed and

full information. For detailed and full information see the relevant full data

sheet, which is available on request via the local NXP Semiconductors sales

office. In case of any inconsistency or conflict with the short data sheet, the

full data sheet shall pre vail.

Product specificatio n — The information and data provided in a Product

data sheet shall define the specification of the product as agreed between

NXP Semiconductors and its customer, unless NXP Semiconductors and

customer have explicitly agreed otherwise in writing. In no event however,

shall an agreement be valid in which the NXP Semiconductors product is

deemed to off er functions and qualities beyond those described in the

Product data sheet.

10.3 Disclaimers

Limited warr a nty and liability — Information in this document is believed to

be accurate and reliable. However, NXP Semiconductors does not give any

representations or warranties, expressed or implied, as to the accuracy or

completeness of such information and shall have no liability for the

consequences of use of such information.

In no event shall NXP Semiconductors be liable for any indirect, incidental,

punitive, special or consequ ential damages (including - wit hout limitatio n - lost

profits, lost savings, business interruption, costs related to the removal or

replacement of any products or rework charges) whether or not such

damages are based on tort (including negligence), warranty, breach of

contract or any other legal theory.

Notwithstanding any damages that customer might incur for any reason

whatsoever, NXP Semiconductors’ ag gregate and cumulative l iability towards

customer for the products described herein shall be limited in accordance

with the Terms and conditions of commercial sale of NXP Semicondu ctors.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all informa tion supplied prior

to the publication hereof .

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suit able for use in life support, life-critical or

safety-critical systems or equipment, nor in applications where failure or

malfunction of an NXP Semiconductors product can reasonably be expected

to result in perso nal injury, death or severe property or environmental

damage. NXP Semiconductors accepts no liab ility for inclusion and/or use of

NXP Semiconductors products in such equipment or applications and

therefore such inclusion and/or use is at the customer’s own risk.

Quick reference data — The Quick reference data i s an extract of the

product data given in the Limiting values and Characteristics sections of this

document, and as such is not complete, exhaustive or legally binding.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes no

representation or warranty tha t such application s will be suitable for the

specified use without further testing or modification.

Customers are responsible for the design and ope ration of their applications

and products using NXP Semiconductors product s, and NXP Semiconductors

accepts no liability for any assistance with applications or customer product

design. It is customer’s sole responsibility to determine whether the NXP

Semiconductors product is suit able and fit for the custome r’s applications and

products planned, as well as fo r the planned application and use of

customer’s third party customer(s). Customers should provide appropriate

design and operating safeguards to minimize the risks associated with their

applications and products.

NXP Semiconductors does not accept any liability rela ted to any default,

damage, costs or problem which is based on any weakness or default in the

customer’s applications or products, or the application or use by customer’s

third party customer(s). Customer is responsible for doing all necessary

testing for th e customer’s applications and products using NXP

Semiconductors products in order to avoid a default of the applications and

the products or of the application or use by customer’s third party

customer(s). NXP does not accept any liability in this respect.

Limiting values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) will cause permanent

damage to the device. Limiting values are stress ratings only and (proper)

operation of the device at these or any other conditions above those given in

the Recommended operating conditions section (if present) or the

Characteristics sections of this document is not warranted. Constant or

repeated exposure to limiting values will permanent ly and irreversibly affect

the quality and reliability of the device.

Terms and conditions of commercial sale — NXP Semiconductors

products are sold subject to the general terms and conditions of commercial

sale, as published at http://www.nxp.com/profile/terms, unless otherwise

agreed in a valid written individua l agreement. In case an individual

agreement is concluded only the ter ms and conditions of the respective

agreement shall apply. NXP Semiconductors hereby expressly objects to

applying the customer’s general terms and conditions with regard to the

purchase of NXP Semiconductors products by customer.

No offer to sell or license — Nothing i n this document may be interpreted or

construed as an of fer t o sell product s that is open for accept ance or t he grant,

conveyance or implication of any license under any copyrights, patents or

other industrial or intellectual property rights.

Document status[1][2] Product status[3] Definition

Objective [short] data sheet Development This document contains data from the objecti ve specification for product development.

Preliminary [short] dat a sheet Qualification This document contains data from the preliminary specification.

Product [short] dat a sheet Production This document contains the product specification.

Product data sheet Rev. 5 — 30 September 2011 12 of 13

NXP Semiconductors BT169 series

Thyristor logic level

Export control — This document as well as the item(s) described herein

may be subject to export control regulations. Export might require a pri or

authorization from competent authorities.

Non-automotive qualified products — Unless this data sheet expressly

states that this specific NXP Semiconductors product is automotive qualified,

the product is not suitable for automotive use. It i s neither qua lif ied nor test ed

in accordance with automotive testing or application requirements. NXP

Semiconductors accepts no liability for inclusion and/or use of

non-automotive qualified products in automotive equipment or applications.

In the event that customer uses the product for design-in and use in

automotive applications to automot ive specifications and standard s, customer

(a) shall use the product without NXP Semiconductors’ warranty of the

product for such automotive applications, use and specifications, and (b)

whenever customer uses the product for automotive applications beyond

NXP Semiconductors’ specifications such use shall be solely at customer’s

own risk, and (c) customer fully indemnifies NXP Semiconductors for any

liability, damages or failed product claims resulting from customer design and

use of the product for automotive applications beyond NXP Semiconductors’

standard warranty and NXP Semiconductors’ product specifications.

10.4 Trademarks

Notice: All referenced b rands, produc t names, service names and trademarks

are the property of their respect i ve ow ners.

11. Contact information

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

NXP Semiconductors BT169 series

Thyristor logic level

For more information, please visit: http://www.nxp.co m

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 30 September 2011

Document identifier: BT169_SER

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

12. Contents

1 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 General description . . . . . . . . . . . . . . . . . . . . . 1

1.2 Features and benefits. . . . . . . . . . . . . . . . . . . . 1

1.3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.4 Quick reference data . . . . . . . . . . . . . . . . . . . . 1

2 Pinning information. . . . . . . . . . . . . . . . . . . . . . 1

3 Ordering information. . . . . . . . . . . . . . . . . . . . . 2

4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 2

5 Thermal characteristics . . . . . . . . . . . . . . . . . . 5

6 Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 6

7 Package information . . . . . . . . . . . . . . . . . . . . . 8

8 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 9

9 Revision history. . . . . . . . . . . . . . . . . . . . . . . . 10

10 Legal information. . . . . . . . . . . . . . . . . . . . . . . 11

10.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 11

10.2 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

10.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 11

10.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

11 Contact information. . . . . . . . . . . . . . . . . . . . . 12

12 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13