LTC4008EGN#PBF - ANALOG DEVICES

LTC4008

Rev C

For more information www.analog.com

TYPICAL APPLICATION

DESCRIPTION

4A, High Efficiency,

Multi-Chemistry Battery Charger

12.3V, 4A Li-Ion Charger

FEATURES

APPLICATIONS

n General Purpose Charger Controller

n High Conversion Efﬁciency: Up to 96%

n Output Currents Exceeding 4A

n ±0.8% Voltage Accuracy

n AC Adapter Current Limiting Maximizes

Charge Rate*

n Thermistor Input for Temperature Qualiﬁed Charging

n Wide Input Voltage Range: 6V to 28V

n Wide Output Voltage: 3V to 28V

n 0.5V Dropout Voltage; Maximum Duty Cycle: 98%

n Programmable Charge Current: ±4% Accuracy

n Indicator Outputs for Charging, C/10 Current

Detection, AC Adapter Present, Input Current

Limiting and Faults

n Charging Current Monitor Output

n Available in a 20-Pin Narrow SSOP Package

n Notebook Computers

n Portable Instruments

n Battery Backup Systems

The LTC®4008 is a constant-current/constant-voltage

charger controller. The PWM controller uses a synchro-

nous, quasi-constant frequency, constant off-time archi-

tecture that will not generate audible noise even when

using ceramic capacitors. Charging current is program-

mable with a sense resistor and programming resistor to

±4% typical accuracy. Charging current can be monitored

as a voltage across the programming resistor. An external

resistor divider and precision internal reference set the

final float voltage.

The LTC4008 includes a thermistor sensor input that will

suspend charging if an unsafe temperature condition is

detected and will automatically resume charging when

battery temperature returns to within safe limits; a FAULT

pin indicates this condition. A FLAG pin indicates when

charging current has decreased below 10% of the pro-

grammed current. An external sense resistor programs

AC adapter current limiting. The I

pin indicates when the

charging current is being reduced by input current limiting

so that the charging algorithm can adapt.

BATMON

VFB

ICL

ACP/SHDN

FAULT

FLAG

NTC

ITH

GND

ICL

ACP

FAULT

FLAG

DCIN

INFET

CLP

CLN

TGATE

BGATE

PGND

CSP

BAT

PROG

LTC4008

32.4k

0.47µF

THERMISTOR

10k

NTC

0.12µF

100k100k

140k*

15k*

6.04k

150k

VLOGIC

DCIN

0V TO 28V 0.1µF

INPUT SWITCH

0.1µF

20µF

10µH

4.99k

3.01k

0.025Ω

0.02Ω

20µF

SYSTEM

LOAD

Li-Ion

BATTERY

CHARGING

CURRENT

MONITOR

26.7k Q1: Si4431BDY

Q2: FDC645N

0.0047µF

4008 TA01

NOTE: * 0.25% TOLERANCE

ALL OTHER RESISTORS ARE 1% TOLERANCE

All registered trademarks and trademarks are the property of their respective owners. Protected

by U.S. Patents including 5723970.

Document Feedback

LTC4008

Rev C

For more information www.analog.com

Voltage from DCIN, CLP, CLN to GND ......... +32V/–0.3 V

PGND with Respect to GND ...................................±0.3V

CSP, BAT to GND .......................................... +28V/–0.3V

VFB, RT to GND ............................................... +7V/–0.3V

NTC ...............................................................+10V/–0.3V

ACP/SHDN, FLAG, FA U LT, ICL ...................... +32V/–0.3V

(Note 1)

ABSOLUTE MAXIMUM RATINGS

CLP to CLN ..........................................................+0.5V

Operating Ambient Temperature Range

(Note 4) ...............................................–40°C to 85°C

Operating Junction Temperature ............ –40°C to 125°C

Storage Temperature Range .................. –65°C to 150°C

Lead Temperature (Soldering, 10 sec) ................... 300°C

LTC4008 LTC4008-1*

GN PACKAGE

20-LEAD NARROW PLASTIC SSOP

TJMAX = 125°C, θJA = 90°C/W

TOP VIEW

INFET

BGATE

PGND

TGATE

CLP

CLN

FLAG

BATMON

BAT

CSP

DCIN

ICL

ACP/SHDN

FAULT

GND

VFB

NTC

ITH

PROG

GN PACKAGE

20-LEAD NARROW PLASTIC SSOP

TJMAX = 125°C, θJA = 90°C/W

TOP VIEW

BGATE

PGND

TGATE

CLP

CLN

FLAG

BATMON

BAT

CSP

DCIN

ICL

SHDN

FAULT

GND

VFB

NTC

ITH

PROG

*The LTC4008EGN-1 does not have the Input FET function

PIN CONFIGURATION

ORDER INFORMATION

LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE

LTC4008EGN#PBF LTC4008EGN#TRPBF LTC4008EGN 20-Lead Narrow Plastic SSOP –40°C to 125°C

LTC4008EGN-1#PBF LTC4008EGN-1#TRPBF LTC4008EGN-1 20-Lead Narrow Plastic SSOP –40°C to 125°C

Consult ADI Marketing for parts specified with wider operating temperature ranges.

For more information on lead free part marking, go to: http://www.linear.com/leadfree/

For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through

designated sales channels with #TRMPBF suffix.

http://www.linear.com/product/LTC4008#orderinfo

LTC4008

Rev C

For more information www.analog.com

ELECTRICAL CHARACTERISTICS

The l denotes the specifications which apply over the full operating

temperature range, otherwise specifications are at TA = 25°C. VDCIN = 20V, VBAT = 12V unless otherwise noted.

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

DCIN Operating Range 6 28 V

IQOperating Current Charging Sum of Current from CLP, CLN, DCIN 3 5 mA

VTOL Voltage Accuracy (Notes 2, 5)

–0.8

–1.0

0.8

1.0

BATMON Error (Note 5) Measured from BAT to BATMON,

RLOAD = 100k

0 35 80 mV

ITOL Charge Current Accuracy (Note 3) VCSP – VBAT Target = 100mV

–4

–5

Shutdown

Battery Leakage Current DCIN = 0V (LTC4008 Only)

ACP/SHDN = 0V

–10

20 35

µA

UVLO Undervoltage Lockout Threshold DCIN Rising, VBAT = 0V l4.2 4.7 5.5 V

Shutdown Threshold at ACP/SHDN l1 1.6 2.5 V

Operating Current in Shutdown VSHDN = 0V, Sum of Current from CLP,

CLN, DCIN

2 3 mA

Current Sense Amplifier, CA1

Input Bias Current Into BAT Pin 11.66 µA

CMSL CA1/I1 Input Common Mode Low l0 V

CMSH CA1/I1 Input Common Mode High VDCIN ≤ 28V lVCLN – 0.2 V

VOS Input Voltage Offset –3.5 3.5 mV

Current Comparators ICMP and IREV

ITMAX Maximum Current Sense Threshold (VCSP – VBAT) VITH = 2.5V l140 165 200 mV

ITREV Reverse Current Threshold (VCSP – VBAT) –30 mV

Current Sense Amplifier, CA2

Transconductance 1 mmho

Source Current Measured at ITH, VITH = 1.4V –40 µA

Sink Current Measured at ITH, VITH = 1.4V 40 µA

Current Limit Amplifier

Transconductance 1.4 mmho

VCLP Current Limit Threshold l93 100 107 mV

ICLN CLN Input Bias Current 100 nA

Voltage Error Amplifier, EA

Transconductance 1 mmho

VREF Reference Voltage Used to Calculate VFLOAT 1.19 V

IBEA Input Bias Current ±4 ±25 nA

Sink Current Measured at ITH, VITH = 1.4V 36 µA

OVSD Overvoltage Shutdown Threshold as a Percent of

Programmed Charger Voltage

l102 107 110 %

LTC4008

Rev C

For more information www.analog.com

ELECTRICAL CHARACTERISTICS

The l denotes the specifications which apply over the full operating

temperature range, otherwise specifications are at TA = 25°C. VDCIN = 20V, VBAT = 12V unless otherwise noted.

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

Input P-Channel FET Driver (INFET) (LTC4008 Only)

DCIN Detection Threshold (VDCIN – VCLP) DCIN Voltage Ramping Up

from VCLP – 0.1V

l0 0.17 0.25 V

Forward Regulation Voltage (VDCIN – VCLP)l25 50 mV

Reverse Voltage Turn-Off Voltage (VDCIN – VCLP) DCIN Voltage Ramping Down l–60 –25 mV

INFET “On” Clamping Voltage (VCLP – VINFET) IINFET = 1µA l5 5.8 6.5 V

INFET “Off” Clamping Voltage (VCLP – VINFET) IINFET = –25µA 0.25 V

Thermistor

NTCVR Reference Voltage During Sample Time 4.5 V

High Threshold VNTC Rising lNTCVR

• 0.48

NTCVR

• 0.5

NTCVR

• 0.52

Low Threshold VNTC Falling lNTCVR

• 0.115

NTCVR

• 0.125

NTCVR

• 0.135

Thermistor Disable Current VNTC ≤ 10V 10 µA

Indicator Outputs (ACP/SHDN, FLAG, ICL, FAULT

C10TOL FLAG (C/10) Accuracy Voltage Falling at PROG l0.375 0.397 0.420 V

ICL Threshold Accuracy VCLP – VCLN 83 93 105 mV

VOL Low Logic Level of ACP/SHDN, FLAG, ICL, FAULT IOL = 100µA 0.5 V

VOH High Logic Level of ACP/SHDN, ICL IOH = –1µA l2.7 V

IOFF Off State Leakage Current of FLAG, FAULT VOH = 3V –1 1 µA

IPO Pull-Up Current on ACP/SHDN, ICL V = 0V –10 µA

Oscillator

fOSC Regulator Switching Frequency 255 300 345 kHz

fMIN Regulator Switching Frequency in Drop Out Duty Cycle ≥ 98% 20 25 kHz

DCMAX Regulator Maximum Duty Cycle VCSP = VBAT 98 99 %

Gate Drivers (TGATE, BGATE)

VTGATE High (VCLP – VTGATE) ITGATE = –1mA 50 mV

VBGATE High CLOAD = 3000pF 5.6 10 V

VTGATE Low (VCLP – VTGATE) CLOAD = 3000pF 5.6 10 V

VBGATE Low IBGATE = 1mA 50 mV

TGTR

TGTF

TGATE T

ransition Time

TGATE Rise Time

TGATE Fall Time

CLOAD = 3000pF, 10% to 90%

110

100

BGTR

BGTF

BGATE T

ransition Time

BGATE Rise Time

BGATE Fall Time

CLOAD = 3000pF, 10% to 90%

VTGATE at Shutdown (VCLP – VTGATE) ITGATE = –1µA, DCIN = 0V, CLP = 12V 100 mV

VBGATE at Shutdown IBGATE = 1µA, DCIN = 0V, CLP = 12V 100 mV

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: See “Test Circuit”.

Note 3: Does not include tolerance of current sense resistor or current

programming resistor.

Note 4: The LTC4008E is guaranteed to meet performance specifications

from 0°C to 70°C. Specifications over the –40°C to 85°C operating

temperature range are assured by design, characterization and correlation

with statistical process controls.

Note 5: Voltage accuracy includes BATMON error and voltage reference

error. Does not include error of external resistor divider.

LTC4008

Rev C

For more information www.analog.com

TYPICAL PERFORMANCE CHARACTERISTICS

INFET Response Time to

Reverse Current VFB vs DCIN

BATMON Offset

(TA = 25°C unless otherwise noted)

TEST PERFORMED ON DEMOBOARD

VIN = 15VDC

CHARGER = ON

ICHARGE = <10mA

Vs OF PFET (5V/DIV)

Id (REVERSE) OF

PFET (5A/DIV)

Vgs OF PFET (2V/DIV)

4008 G01

VCHARGE = 12.6V

INFET = 1/2 Si4925DY

Vgs = 0

Vs = 0V

Id = 0A

1.25µs/DIV

DCIN (V)

6 11 16 21 26

(%)

4008 G02

0.05

–0.05

–0.10

–0.15

–0.20

BATTERY VOLTAGE (V)

3 8 13 18 23

BATTERY

- V

BATMON

(V)

4008 G03

0.02

–0.02

–0.04

–0.06

–0.08

–0.10

DCIN = 15V

DCIN = 20V

DCIN = 24V

BATMON LOAD = 100kΩ

VOUT vs IOUT

PWM Frequency vs Duty Cycle

Disconnect/Reconnect Battery

(Load Dump)

OUTPUT CURRENT (A)

0 0.5 1.0 2.0 3.0 4.01.5 2.5 3.5 4.5

OUTPUT VOLTAGE ERROR (%)

4008 G04

DCIN = 20V

VBAT = 12.6V

–0.5

–1.0

–1.5

–2.0

–2.5

–3.0

–3.5

–4.0

–4.5

–5.0

DUTY CYCLE (VOUT/VIN)

0 0.1 0.2 0.4 0.6 0.90.80.3 0.5 0.7 1.0

PWM FREQUENCY (kHz)

4008 G05

PROGRAMMED CURRENT = 10%

DCIN = 15V

DCIN = 20V

DCIN = 24V

350

300

250

200

150

100

4008 G06

LOAD CURRENT = 1A, 2A, 3A

DCIN = 20V

VFLOAT = 12.6V

VFLOAT

1V/(DIV)

LOAD

STATE DISCONNECT RECONNECT

1A STEP

3A STEP

1A STEP

LTC4008

Rev C

For more information www.analog.com

TYPICAL PERFORMANCE CHARACTERISTICS

Battery Leakage Current vs

Battery Voltage Efficiency at 19VDC VIN

Efficiency at 12.6V with 15VDC

VIN

Charging Voltage Error

TEMP = 27°C, ILOAD = 0.120A

(TA = 25°C unless otherwise noted)

BATTERY VOLTAGE (V)

0 5 10 15 20 25 30

BATTERY LEAKAGE CURRENT (µA)

4008 G07

VDCIN = 0V

CHARGE CURRENT (A)

1.000.50 1.50 2.00 2.50 3.00

EFFICIENCY (%)

4008 G09

16.8V

12.6V

100

CHARGE CURRENT (A)

1.000.50 1.50 2.00 2.50 3.00

EFFICIENCY (%)

4008 G10

100

CHARGING VOLTAGE (V)

OUTPUT VOLTAGE ERROR (V)

0.150

0.100

0.125

0.075

0.050

0.025

–0.025

–0.050

–0.075

–0.100

–0.125

–0.150 16

4008 G11

42 6 10 14 18

812 2220

DCIN = 15V

DCIN = 20V

LTC4008

Rev C

For more information www.analog.com

PIN FUNCTIONS

DCIN (Pin 1): External DC Power Source Input. Bypass this

pin with at least 0.01µF. See “Applications Information”

section.

ICL (Pin 2): Input Current Limit Indicator. Active low dig-

ital output. Internal 10µA pull-up to 3.5V. Pulled low if

the charger current is being reduced by the input current

limiting function. The pin is capable of sinking at least

100µA. If VLOGIC > 3.3V, add an external pull-up.

ACP/SHDN (Pin 3): Open-drain output used to indicate if

the AC adapter voltage is adequate for charging. Active high

digital output. Internal 10µA pull-up to 3.5V. The charger

can also be shutdown by pulling this pin below 1V. The pin

is capable of sinking at least 100µA. If VLOGIC > 3.3V, add

an external pull-up. (LTC4008-1: ACP function disabled.)

RT (Pin 4): Thermistor Clocking Resistor. Use a 150k resis-

tor as a nominal value. This resistor is always required.

If this resistor is not present, the charger will not start.

FAULT (Pin 5): Active low open-drain output that indi-

cates that charger operation has suspended due to the

thermistor exceeding allowed values. A pull-up resistor

is required if this function is used. The pin is capable of

sinking at least 100µA.

GND (Pin 6): Ground for Low Power Circuitry.

(Pin 7): Input of Voltage Feedback Error Amplifier,

EA, in the “Block Diagram”.

NTC (Pin 8): A thermistor network is connected from NTC

to GND. This pin determines if the battery temperature is

safe for charging. The charger and timer are suspended

and the FAULT pin is driven low if the thermistor indicates

a temperature that is unsafe for charging. The thermistor

function may be disabled with a 300k to 500k resistor

from DCIN to NTC.

ITH (Pin 9): Control Signal of the Inner Loop of the Current

Mode PWM. Higher I

voltage corresponds to higher

charging current in normal operation. A 6k resistor in

series with a capacitor of at least 0.1µF to GND provides

loop compensation. Typical full-scale output current is

40µA. Nominal voltage range for this pin is 0V to 3V.

PROG (Pin 10): Current Programming/Monitoring Input/

Output. An external resistor to GND programs the peak

charging current in conjunction with the current sensing

resistor. The voltage at this pin provides a linear indica-

tion of charging current. Peak current is equivalent to

1.19V. Zero current is approximately 0.309V. A capaci-

tor from PROG to ground is required to filter higher fre-

quency components. The maximum program resistance

to ground is 100k. Values higher than 100k can cause the

charger to shut down.

CSP (Pin 11): Current Amplifier CA1 Input. The CSP and

BAT pins measure the voltage across the sense resis-

tor, R

SENSE

, to provide the instantaneous current signals

required for both peak and average current mode operation.

BAT (Pin 12): Battery Sense Input and the Negative

Reference for the Current Sense Resistor.

BATMON (Pin 13): Output Voltage Representing Battery

Voltage. Switched off to reduce standby current drain

when AC is not present. An external voltage divider

from BATMON to VFB sets the charger float voltage.

Recommended minimum load resistance is 100k.

FLAG (Pin 14): Active low open-drain output that indi-

cates when charging current has declined to 10% of max

programmed current. A pull-up resistor is required if this

function is used. The pin is capable of sinking at least

100µA. This function is latching. To clear it, user must

cycle the ACP/SHDN pin.

CLN (Pin 15): Negative Input to the Input Current Limiting

Amplifier CL1. The threshold is set at 100mV below the

voltage at the CLP pin. When used to limit input current,

a filter is needed to filter out the switching noise. If no

current limit function is desired, connect this pin to CLP.

CLP (Pin 16): This pin serves as a positive reference for

the input current limit amplifier, CL1. It also serves as the

power supply for the IC.

TGATE (Pin 17): Drives the top external PMOSFET of the

battery charger buck converter.

PGND (Pin 18): High Current Ground Return for BGATE

Driver.

BGATE (Pin 19): Drives the bottom external N-MOSFET

of the battery charger buck converter.

INFET (Pin 20): Drives the gate of the external input

P-MOSFET. (LTC4008-1: No Connection)

LTC4008

Rev C

For more information www.analog.com

BLOCK DIAGRAM

–

1.19V

11.67µA

35mV

C/10

TBAD

gm = 1m

1.19V

FLAG

GND

ICL

TGATE

BGATE

CLP

100mV

0.1µF

20µF

RCL 5k

CLN

PGND

397mV

NTC

0.47µF 10k

NTC

150k

–

CL1

gm = 1.4m

CONTROL

BLOCK

THERMISTOR

OSCILLATOR 4

BAT 3k

RSENSE

CSP

ITH

32.4k

WATCHDOG

DETECT tOFF

CLP

DCIN

OSCILLATOR

1.28V

PWM

LOGIC

CHARGE

–

ICMP

–

÷5

BUFFERED ITH

0.1µF

PROG

4008 BD

RPROG

26.7k

4.7nF

FAULT 5

ACP/SHDN 3

INFET*

DCIN

VIN

–

CLP

–

5.8V *NOT USED IN THE LTC4008-1

20µF

0.12µF

–

CA1

CA2

–

VFB

BATMON

IREV

–

* *

17mV

LTC4008

Rev C

For more information www.analog.com

OPERATION

TEST CIRCUIT

–

LT1055

LTC4008

VREF

BAT

13 12

CSP

11 ITH

0.6V

4008 TC

BATMON

90.325k

9.675k

VFB

OVERVIEW

The LTC4008 is a synchronous current mode PWM step

down (buck) switcher battery charger controller. The

charge current is programmed by the combination of a

program resistor (RPROG) from the PROG pin to ground

and a sense resistor (RSENSE) between the CSP and BAT

pins. The final float voltage is programmed with an exter-

nal resistor divider and the internal 1.19V reference volt-

age. Charging begins when the potential at the DCIN pin

rises above the voltage at BAT (and the UVLO voltage)

and the ACP/SHDN pin is high. An external thermistor

network is sampled at regular intervals. If the thermistor

value exceeds design limits, charging is suspended and

the FAULT pin is set low. If the thermistor value returns

to an acceptable value, charging resumes and the FAULT

pin is set high. An external resistor on the RT pin sets the

sampling interval for the thermistor.

As the battery approaches the final float voltage, the

charge current will begin to decrease. When the current

drops to 10% of the full-scale charge current, an internal

C/10 comparator will indicate this condition by latching

the FLAG pin low. If this condition is caused by an input

current limit condition, described below, then the FLAG

indicator will be inhibited. When the input voltage is not

present, the charger goes into a sleep mode, dropping

battery current drain to 15µA. This greatly reduces the

current drain on the battery and increases the standby

time. The charger can be inhibited at any time by forcing

the ACP/SHDN pin to a low voltage. Forcing ACP/SHDN

low, or removing the voltage from DCIN, will also clear

the FLAG pin if it is low.

Table1. Truth Table For Indicator States

MODE DCIN ACP/SHDN FLAG** FAULT** ICL

Shutdown by low adapter voltage (Disabled on LTC4008-1) <BAT LOW HIGH HIGH LOW

Normal charging >BAT HIGH HIGH HIGH* HIGH*

Input current limited charging >BAT HIGH HIGH* HIGH* LOW

Charger shut down due to thermistor out of range >BAT HIGH X LOW HIGH

Shut down by ACP/SHDN pin (USER) X Forced LOW HIGH HIGH LOW

Shut down by undervoltage lockout >BAT + <UVL HIGH HIGH HIGH* LOW

*Most probable condition, **Open-drain output, HIGH = Open with pull-up, X = Don’t care

LTC4008

Rev C

For more information www.analog.com

OPERATION

Input FET (LTC4008)

The input FET circuit performs two functions. It enables

the charger if the input voltage is higher than the CLP

pin and provides the logic indicator of AC present on the

ACP/SHDN pin. It controls the gate of the input FET to

keep a low forward voltage drop when charging and also

prevents reverse current flow through the input FET.

If the input voltage is less than VCLP

, it must go at least

170mV higher than VCLN to activate the charger. When this

occurs the ACP/SHDN pin is released and pulled up with

an external load to indicate that the adapter is present.

The gate of the input FET is driven to a voltage sufficient

to keep a low forward voltage drop from drain to source.

If the voltage between DCIN and CLP drops to less than

25mV, the input FET is turned off slowly. If the voltage

between DCIN and CLP is ever less than –25mV, then

the input FET is turned off in less than 10µs to prevent

significant reverse current from flowing in the input FET.

In this condition, the ACP/SHDN pin is driven low and the

charger is disabled.

Input FET (LTC4008-1)

The input FET circuit is disabled for the LTC4008-1. There

is no low current shutdown mode when DCIN falls below

the CLP pin. The ACP/SHDN pin functions only to shut

down the charger.

Battery Charger Controller

The LTC4008 charger controller uses a constant off-time,

current mode step-down architecture. During normal

operation, the top MOSFET is turned on each cycle when

the oscillator sets the SR latch and turned off when the

main current comparator ICMP resets the SR latch. While

the top MOSFET is off, the bottom MOSFET is turned on

until either the inductor current trips the current compar-

ator IREV or the beginning of the next cycle. The oscillator

uses the equation:

tOFF =

DCIN

– V

BAT

DCIN

• f

OSC

to set the bottom MOSFET on time. This activity is dia-

grammed in Figure1.

The peak inductor current, at which ICMP resets the SR

latch, is controlled by the voltage on ITH. ITH is in turn

controlled by several loops, depending upon the situation

at hand. The average current control loop converts the

voltage between CSP and BAT to a representative cur-

rent. Error amp CA2 compares this current against the

desired current programmed by RPROG at the PROG pin

and adjusts ITH until:

VREF

PROG

=VCSP – VBAT +11.67μA • 3.01kΩ

3.01kΩ

therefore,

ICHARGE(MAX) =VREF

PROG

– 11.67μA

⎛

⎝

⎜

⎞

⎠

⎟•3.01kΩ

SENSE

The voltage at BATMON is divided down by an external

resistor divider and is used by error amp EA to decrease

if the divider voltage is above the 1.19V reference.

When the charging current begins to decrease, the voltage

at PROG will decrease in direct proportion. The voltage at

PROG is then given by:

VPROG =ICHARGE •RSENSE +11.67μA • 3.01kΩ

( )

•RPROG

3.01kΩ

The accuracy of VPROG will range from 0% to ITOL.

VPROG is plotted in Figure2.

The amplifier CL1 monitors and limits the input current,

normally from the AC adapter to a preset level (100mV/

). At input current limit, CL1 will decrease the I

volt-

age, thereby reducing charging current. The ICL indicator

output will go low when this condition is detected and

the FLAG indicator will be inhibited if it is not already low.

TGATE

OFF

BGATE

INDUCTOR

CURRENT

tOFF

TRIP POINT SET BY ITH VOLTAGE

OFF

4008 F01

Figure1.

LTC4008

Rev C

For more information www.analog.com

OPERATION

If the charging current decreases below 10% to 15% of

programmed current, while engaged in input current limit-

ing, BGATE will be forced low to prevent the charger from

discharging the battery. Audible noise can occur in this

mode of operation.

An overvoltage comparator guards against voltage tran-

sient overshoots (>7% of programmed value). In this

case, both MOSFETs are turned off until the overvoltage

condition is cleared. This feature is useful for batteries

which “load dump” themselves by opening their protec-

tion switch to perform functions such as calibration or

pulse mode charging.

PWM Watchdog Timer

There is a watchdog timer that observes the activity on

the BGATE and TGATE pins. If TGATE stops switching for

more than 40µs, the watchdog activates and turns off the

top MOSFET for about 400ns. The watchdog engages to

prevent very low frequency operation in dropout which

is a potential source of audible noise when using ceramic

input and output capacitors.

Charger Startup

When the charger is enabled, it will not begin switching

until the ITH voltage exceeds a threshold that assures ini-

tial current will be positive. This threshold is 5% to 15%

of the maximum programmed current (100mV/RSENSE).

After the charger begins switching, the various loops will

control the current at a level that is higher or lower than

the initial current. The duration of this transient condition

depends upon the loop compensation but is typically less

than 100µs.

Thermistor Detection

The thermistor detection circuit is shown in Figure3. It

requires an external resistor and capacitor in order to

function properly.

ICHARGE (% OF MAXIMUM CURRENT)

PROG

(V)

0.2

0.4

0.6

0.8

4008 F02

1.0

1.2

20 40 60 80 100

1.19V

0.309V

Figure2. VPROG vs ICHARGE

8NTC

LTC4008

R10

32.4k

0.47µF

RTH

10k

NTC

–

60k

~4.5V

CLK

45k

15k

TBAD

4008 F03

Figure3.

LTC4008

Rev C

For more information www.analog.com

OPERATION

The thermistor detector performs a sample-and-hold

function. An internal clock, whose frequency is deter-

mined by the timing resistor connected to RT

, keeps

switch S1 closed to sample the thermistor:

tSAMPLE = 127.5 • 20 • RRT • 17.5pF = 6.7ms,

for RRT = 150k

The external RC network is driven to approximately 4.5V

and settles to a final value across the thermistor of:

VRTH(FINAL) =

4.5V •R

+R10

This voltage is stored by C7. Then the switch is opened

for a short period of time to read the voltage across the

thermistor.

tHOLD = 10 • RRT • 17.5pF = 26µs,

for RRT = 150k

When the tHOLD interval ends the result of the thermistor

testing is stored in the D flip-flop (DFF). If the voltage at

NTC is within the limits provided by the resistor divider

feeding the comparators, then the NOR gate output will

be low and the DFF will set TBAD to zero and charging will

continue. If the voltage at NTC is outside of the resistor

divider limits, then the DFF will set TBAD to one, the charger

will be shut down, FAULT pin is set low and the timer will

be suspended until TBAD returns to zero (Figure4).

CLK

(NOT TO

SCALE)

VNTC

tSAMPLE

VOLTAGE ACROSS THERMISTOR

tHOLD

4008 F04

COMPARATOR HIGH LIMIT

COMPARATOR LOW LIMIT

Figure4.

LTC4008

Rev C

For more information www.analog.com

APPLICATIONS INFORMATION

Charger Current Programming

The basic formula for charging current is:

ICHARGE(MAX) =

REF

• 3.01k

/ R

PROG

– 0.035V

SENSE

VREF = 1.19V. This leaves two degrees of freedom: RSENSE

and RPROG. The 3.01k input resistors must not be altered

since internal currents and voltages are trimmed for this

value. Pick R

SENSE

by setting the average voltage between

CSP and BAT to be close to 100mV during maximum

charger current. Then RPROG can be determined by solv-

ing the above equation for RPROG.

RPROG =VREF • 3.01kΩ

RSENSE •ICHARGE(MAX) +0.035V

Table2. Recommended RSNS and RPROG Resistor Values

IMAX (A) RSENSE (Ω) 1% RSENSE (W) RPROG (kΩ) 1%

1.0 0.100 0.25 26.7

2.0 0.050 0.25 26.7

3.0 0.033 0.5 26.7

4.0 0.025 0.5 26.7

Charging current can be programmed by pulse width mod-

ulating RPROG with a switch Q1 to RPROG at a frequency

higher than a few kHz (Figure5). CPROG must be increased

to reduce the ripple caused by the RPROG switching. The

compensation capacitor at ITH will probably need to be

increased also to improve stability and prevent large

overshoot currents during start-up conditions. Charging

current will be proportional to the duty cycle of the switch

with full current at 100% duty cycle and zero current when

Q1 is off.

Maintaining C/10 Accuracy

The C/10 comparator threshold that drives the FLAG pin

has a fixed threshold of approximately VPROG = 400mV.

This threshold works well when RPROG is 26.7k, but will

not yield a 10% charging current indication if RPROG

is a different value. There are situations where a stan-

dard value of RSENSE will not allow the desired value of

charging current when using the preferred RPROG value.

In these cases, where the full-scale voltage across RSENSE

is within ±20mV of the 100mV full-scale target, the input

resistors connected to CSP and BAT can be adjusted to

provide the desired maximum programming current as

well as the correct FLAG trip point.

For example, the desired max charging current is 2.5A but

the best RSENSE value is 0.033Ω. In this case, the volt-

age across RSENSE at maximum charging current is only

82.5mV, normally RPROG would be 30.1k but the nominal

FLAG trip point is only 5% of maximum charging current.

If the input resistors are reduced by the same amount as

the full-scale voltage is reduced then, R4 = R5 = 2.49k and

RPROG = 26.7k, the maximum charging current is still 2.5A

but the FLAG trip point is maintained at 10% of full scale.

There are other effects to consider. The voltage across the

current comparator is scaled to obtain the same values

as the 100mV sense voltage target, but the input referred

sense voltage is reduced, causing some careful consid-

eration of the ripple current. Input referred maximum

comparator threshold is 117mV, which is the same ratio

of 1.4x the DC target. Input referred IREV threshold is

scaled back to –24mV. The current at which the switcher

starts will be reduced as well so there is some risk of

boost activity. These concerns can be addressed by using

a slightly larger inductor to compensate for the reduction

of tolerance to ripple current.

102k

CPROG

4008 F05

LTC4008

PROG

2N7002

RPROG

Figure5. PWM Current Programming

LTC4008

Rev C

For more information www.analog.com

APPLICATIONS INFORMATION

Battery Conditioning

Some batteries require a small charging current to condi-

tion them when they are severely depleted. The charging

current is switched to a high rate after the battery volt-

age has reached a “safe” voltage to do so. Figure6 illus-

trates how to do this 2-level charging. When Q1 is on, the

charger current is set to maximum. When Q1 is off, the

charging current is set to 10% of the maximum.

53.6k

CPROG

0.0047µF

4008 F06

LTC4008

2N7002

26.7k

PROG

Figure6. 2-Level Current Programming

Charger Voltage Programming

A resistor divider, R8 and R9 (see Figure10), programs

the final float voltage of the charger. The equation for float

voltage is (the input bias current of EA is typically –4nA

and can be ignored):

VFLOAT = VREF (1 + R8/R9)

It is recommended that the sum of R8 and R9 not be less

than 100k. Accuracy of the LTC4008 voltage reference is

±0.8% at 25°C, and ±1% over the full temperature range.

This leads to the possibility that very accurate (0.1%)

resistors might be needed for R8 and R9. Actually, the

temperature of the LTC4008 will rarely exceed 50°C near

the float voltage because charging currents have tapered

to a low level, so 0.25% resistors will normally provide the

required level of overall accuracy. Table3 contains recom-

mended values for R8 and R9 for popular float voltages.

Table3.

FLOAT VOLTAGE (V) R9 (kΩ) 0.25% R8 (kΩ) 0.25%

8.2 24.9 147

8.4 26.1 158

12.3 15 140

12.6 16.9 162

16.4 11.5 147

16.8 13.3 174

Soft-Start

The LTC4008 is soft started by the 0.12µF capacitor on the

ITH pin. On start-up, ITH pin voltage will rise quickly to 0.5V,

then ramp up at a rate set by the internal 40µA pull-up cur-

rent and the external capacitor. Battery charging current

starts ramping up when ITH voltage reaches 0.8V and full

current is achieved with I

at 2V. With a 0.12µF capacitor,

time to reach full charge current is about 2ms and it is

assumed that input voltage to the charger will reach full

value in less than 2ms. The capacitor can be increased up

to 1µF if longer input start-up times are needed.

Input and Output Capacitors

The input capacitor (C2) is assumed to absorb all input

switching ripple current in the converter, so it must have

adequate ripple current rating. Worst-case RMS ripple

current will be equal to one-half of output charging cur-

rent. Actual capacitance value is not critical. Solid tanta-

lum low ESR capacitors have high ripple current rating

in a relatively small surface mount package, but caution

must be used when tantalum capacitors are used for input

or output bypass. High input surge currents can be cre-

ated when the adapter is hot-plugged to the charger or

when a battery is connected to the charger. Solid tantalum

capacitors have a known failure mechanism when sub-

jected to very high turn-on surge currents. Kemet T495

series of “Surge Robust” low ESR tantalums are rated for

high surge conditions such as battery to ground.

LTC4008

Rev C

For more information www.analog.com

APPLICATIONS INFORMATION

The relatively high ESR of an aluminum electrolytic for

C1, located at the AC adapter input terminal, is helpful

in reducing ringing during the hot-plug event. Refer to

Application Note 88 for more information.

Highest possible voltage rating on the capacitor will mini-

mize problems. Consult with the manufacturer before use.

Alternatives include high capacity ceramic (at least 20µF)

from Tokin, United Chemi-Con/Marcon, et al. Other alter-

native capacitors include OS-CON capacitors from Sanyo.

The output capacitor (C3) is also assumed to absorb

output switching current ripple. The general formula for

capacitor current is:

IRMS =

0.29 VBAT

( )

1– VBAT

VDCIN

⎛

⎝

⎜

⎞

⎠

⎟

( )

For example:

VDCIN = 19V, VBAT = 12.6V, L1 = 10µH, and

f = 300kHz, IRMS = 0.41A.

EMI considerations usually make it desirable to min-

imize ripple current in the battery leads, and beads or

inductors may be added to increase battery impedance

at the 300kHz switching frequency. Switching ripple cur-

rent splits between the battery and the output capacitor

depending on the ESR of the output capacitor and the bat-

tery impedance. If the ESR of C3 is 0.2Ω and the battery

impedance is raised to 4Ω with a bead or inductor, only

5% of the current ripple will flow in the battery.

Inductor Selection

Higher operating frequencies allow the use of smaller

inductor and capacitor values. A higher frequency gener-

ally results in lower efficiency because of MOSFET gate

charge losses. In addition, the effect of inductor value

on ripple current and low current operation must also

be considered. The inductor ripple current ∆IL decreases

with higher frequency and increases with higher VIN.

∆IL=1

( )

VOUT 1– VOUT

⎛

⎝

⎜

⎞

⎠

⎟

Accepting larger values of ∆I

allows the use of low induc-

tances, but results in higher output voltage ripple and

greater core losses. A reasonable starting point for setting

ripple current is ∆IL = 0.4(IMAX). In no case should ∆IL

exceed 0.6(IMAX) due to limits imposed by IREV and CA1.

Remember the maximum ∆IL occurs at the maximum

input voltage. In practice 10µH is the lowest value rec-

ommended for use.

Lower charger currents generally call for larger inductor

values. Use Table4 as a guide for selecting the correct

inductor value for your application.

Table4.

MAXIMUM AVERAGE

CURRENT (A)

INPUT

VOLTAGE (V)

MINIMUM INDUCTOR

VALUE (µH)

1 ≤20 40 ±20%

1 >20 56 ±20%

2 ≤20 20 ±20%

2 >20 30 ±20%

3 ≤20 15 ±20%

3 >20 20 ±20%

4 ≤20 10 ±20%

4 >20 15 ±20%

Charger Switching Power MOSFET

and Diode Selection

Two external power MOSFETs must be selected for use

with the charger: a P-channel MOSFET for the top (main)

switch and an N-channel MOSFET for the bottom (syn-

chronous) switch.

The peak-to-peak gate drive levels are set internally. This

voltage is typically 6V. Consequently, logic-level threshold

MOSFETs must be used. Pay close attention to the BVDSS

specification for the MOSFETs as well; many of the logic

level MOSFETs are limited to 30V or less.

LTC4008

Rev C

For more information www.analog.com

APPLICATIONS INFORMATION

Selection criteria for the power MOSFETs include the “ON”

resistance RDS(ON), total gate capacitance QG, reverse

transfer capacitance CRSS, input voltage and maximum

output current. The charger is operating in continuous

mode so the duty cycles for the top and bottom MOSFETs

are given by:

Main Switch Duty Cycle = VOUT/VIN

Synchronous Switch Duty Cycle = (VIN – VOUT)/VIN.

The MOSFET power dissipations at maximum output cur-

rent are given by:

PMAIN = VOUT/VIN(IMAX)2(1 + δ∆T)RDS(ON)

+ k(VIN)2(IMAX)(CRSS)(fOSC)

PSYNC = (VIN – VOUT)/VIN(IMAX)2(1 + δ∆T)RDS(ON)

Where δ∆T is the temperature dependency of R

DS(ON)

and k is a constant inversely related to the gate drive

current. Both MOSFETs have I2R losses while the PMAIN

equation includes an additional term for transition losses,

which are highest at high input voltages. For VIN < 20V

the high current efficiency generally improves with larger

MOSFETs, while for VIN > 20V the transition losses rap-

idly increase to the point that the use of a higher RDS(ON)

device with lower CRSS actually provides higher effi-

ciency. The synchronous MOSFET losses are greatest at

high input voltage or during a short circuit when the duty

cycle in this switch in nearly 100%. The term (1 + δ∆T) is

generally given for a MOSFET in the form of a normalized

RDS(ON) vs temperature curve, but δ = 0.005/°C can be

used as an approximation for low voltage MOSFETs. CRSS

= QGD/∆VDS is usually specified in the MOSFET charac-

teristics. The constant k = 2 can be used to estimate the

contributions of the two terms in the main switch dissi-

pation equation.

If the charger is to operate in low dropout mode or with

a high duty cycle greater than 85%, then the topside

P-channel efficiency generally improves with a larger

MOSFET. Using asymmetrical MOSFETs may achieve cost

savings or efficiency gains.

The Schottky diode D1, shown in the “Typical Application”

on the back page, conducts during the dead-time between

the conduction of the two power MOSFETs. This prevents

the body diode of the bottom MOSFET from turning on

and storing charge during the dead-time, which could cost

as much as 1% in efficiency. A 1A Schottky is generally

a good size for 4A regulators due to the relatively small

average current. Larger diodes can result in additional

transition losses due to their larger junction capacitance.

The diode may be omitted if the efficiency loss can be

tolerated.

Calculating IC Power Dissipation

The power dissipation of the LTC4008 is dependent upon

the gate charge of the top and bottom MOSFETs (QG1 &

QG2 respectively) The gate charge is determined from the

manufacturer’s data sheet and is dependent upon both

the gate voltage swing and the drain voltage swing of the

MOSFET. Use 6V for the gate voltage swing and VDCIN for

the drain voltage swing.

PD = VDCIN • (fOSC (QG1 + QG2) + IQ)

Example:

VDCIN = 19V, fOSC = 345kHz, QG1 = QG2 = 15nC,

IQ = 5mA

PD = 292mW

Adapter Limiting

An important feature of the LTC4008 is the ability to

automatically adjust charging current to a level which

avoids overloading the wall adapter. This allows the prod-

uct to operate at the same time that batteries are being

charged without complex load management algorithms.

Additionally, batteries will automatically be charged at the

maximum possible rate of which the adapter is capable.

This feature is created by sensing total adapter output cur-

rent and adjusting charging current downward if a preset

adapter current limit is exceeded. True analog control is

LTC4008

Rev C

For more information www.analog.com

APPLICATIONS INFORMATION

used, with closed-loop feedback ensuring that adapter load

current remains within limits. Amplifier CL1 in Figure7

senses the voltage across R

, connected between the

CLP and CLN pins. When this voltage exceeds 100mV,

the amplifier will override programmed charging current

to limit adapter current to 100mV/RCL. A lowpass filter

formed by 5kΩ and 15nF is required to eliminate switch-

ing noise. If the current limit is not used, CLN should be

connected to CLP.

Note that the ICL pin will be asserted when the voltage

across RCL is 93mV, before the adapter limit regulation

threshold.

–

CLP

15nF 5k

RCL*

VIN

LTC4008

CLN

100mV

4008 F07

CIN

SYSTEM

LOAD

CL1

*RCL = 100mV

ADAPTER CURRENT LIMIT

Figure7. Adapter Current Limiting

Setting Input Current Limit

To set the input current limit, you need to know the min-

imum wall adapter current rating. Subtract 7% for the

input current limit tolerance and use that current to deter

mine the resistor value.

RCL = 100mV/ILIM

ILIM = Adapter Min Current –

(Adapter Min Current • 7%)

Table5. Common RCL Resistor Values

ADAPTER

RATING (A)

RCL VALUE*

(Ω) 1%

RCL POWER

DISSIPATION (W)

RCL POWER

RATING (W)

1.5 0.06 0.135 0.25

1.8 0.05 0.162 0.25

2 0.045 0.18 0.25

2.3 0.039 0.206 0.25

2.5 0.036 0.225 0.5

2.7 0.033 0.241 0.5

3 0.03 0.27 0.5

*Values shown above are rounded to nearest standard value.

As is often the case, the wall adapter will usually have at

least a +10% current limit margin and many times one

can simply set the adapter current limit value to the actual

adapter rating (see Table5).

Designing the Thermistor Network

There are several networks that will yield the desired func-

tion of voltage vs temperature needed for proper opera-

tion of the thermistor. The simplest of these is the voltage

divider shown in Figure8. Unfortunately, since the HIGH/

LOW comparator thresholds are fixed internally, there is

only one thermistor type that can be used in this network;

the thermistor must have a HIGH/LOW resistance ratio of

1:7. If this happy circumstance is true for you, then simply

set R9 = RTH(LOW)

LTC4008

NTC

C7 RTH

4008 F08

Figure8. Voltage Divider Thermistor Network

LTC4008

Rev C

For more information www.analog.com

APPLICATIONS INFORMATION

If you are using a thermistor that doesn’t have a 1:7 HIGH/

LOW ratio, or you wish to set the HIGH/LOW limits to

different temperatures, then the more generic network in

Figure9 should work.

Once the thermistor, RTH

, has been selected and the

thermistor value is known at the temperature limits, then

resistors R9 and R9A are given by:

For NTC thermistors:

R9 = 6 RTH(LOW) • RTH(HIGH)/(RTH(LOW) – RTH(HIGH))

R9A = 6 RTH(LOW) • RTH(HIGH)/(RTH(LOW) – 7 •

RTH(HIGH))

Where RTH(LOW) > 7 • RTH(HIGH)

For PTC thermistors:

R9 = 6 RTH(LOW) • RTH(HIGH)/(RTH(HIGH) – RTH(LOW))

R9A = 6 RTH(LOW) • RTH(HIGH)/(RTH(HIGH) – 7 •

RTH(LOW))

Where RTH(HIGH) > 7 • RTH(LOW)

Example #1: 10kΩ NTC with custom limits

TLOW = 0°C, THIGH = 50°C

RTH = 10k at 25°C,

RTH(LOW) = 32.582k at 0°C

RTH(HIGH) = 3.635k at 50°C

R9 = 24.55k → 24.3k (nearest 1% value)

R9A = 99.6k → 100k (nearest 1% value)

Figure9. General Thermistor Network

LTC4008

NTC

C7 R9A RTH

4008 F09

Example #2: 100kΩ NTC

TLOW = 5°C, THIGH = 50°C

RTH = 100k at 25°C,

RTH(LOW) = 272.05k at 5°C

RTH(HIGH) = 33.195k at 50°C

R9 = 226.9k → 226k (nearest 1% value)

R9A = 1.365M → 1.37M (nearest 1% value)

Example #3: 22kΩ PTC

TLOW = 0°C, THIGH = 50°C

RTH = 22k at 25°C,

RTH(LOW) = 6.53k at 0°C

RTH(HIGH) = 61.4k at 50°C

R9 = 43.9k → 44.2k (nearest 1% value)

R9A = 154k

Sizing the Thermistor Hold Capacitor

During the hold interval, C7 must hold the voltage across

the thermistor relatively constant to avoid false readings.

A reasonable amount of ripple on NTC during the hold

interval is about 10mV to 15mV. Therefore, the value of

C7 is given by:

C7 = tHOLD/(R9/7 • – ln(1 – 8 • 15mV/4.5V))

= 10 • RRT • 17.5pF/(R9/7 • – ln(1 – 8 • 15mV/4.5V)

Example:

R9 = 24.3k

RRT = 150k

C7 = 0.28µF → 0.27µF (nearest value)

LTC4008

Rev C

For more information www.analog.com

APPLICATIONS INFORMATION

Disabling the Thermistor Function

If the thermistor is not needed, connecting a resistor

between DCIN and NTC will disable it. The resistor should

be sized to provide at least 10µA with the minimum volt-

age applied to DCIN and 10V at NTC. Do not exceed 30µA.

Generally, a 301k resistor will work for DCIN less than

15V. A 499k resistor is recommended for DCIN between

15V and 24V.

Using the LTC4008-1 (Refer to Figure10)

The LTC4008-1 is intended for applications where the

battery power is fully isolated from the charger and wall

adapter connections. An example application is a sys-

tem with multiple batteries such that the charger’s out-

put power passes through a downstream power path or

selector system. Typically these systems also provide iso-

lation and control the wall adapter power. To reduce cost

in such systems, the LTC4008-1 removes the requirement

for the wall adapter INFET function or blocking diode.

Wall adapter or ACP detection is also removed along with

micropower shutdown mode. Asserting of the SHDN pin

only puts the charger into standby mode. Failure to isolate

the battery power from ANY of the LTC4008-1 pins when

wall adapter power is removed or lost will only drain the

battery at the IC quiescent current rate. More specifically,

high current is drawn from the DCIN, CLP and CLN pins.

Suggested devices to isolate power from the charger

include simple diodes, electrical or mechanical switches

or power path control devices such as the LTC4412 low

loss PowerPath™ controller.

Because the switcher operation is continuous under nearly

all conditions, precautions must be taken to prevent the

charger from boosting the input voltage above maximum

voltage values on the input capacitors or adapter. Z1 and

Q3 will shut down the charger if the input voltage exceeds

a safe value.

LTC4008

Rev C

For more information www.analog.com

APPLICATIONS INFORMATION

BATMON

VFB

ICL

SHDN

FAULT

FLAG

NTC

ITH

GND

ICL

FAULT

FLAG

DCIN

CLP

CLN

TGATE

BGATE

PGND

CSP

BAT

PROG

LTC4008-1

R10 32.4k 1%

140k

0.25%

0.12µF

THERMISTOR

10k

NTC

2N7002

0.47µF

R12

100k

R11

100k

VLOGIC

DCIN

0V TO 28V

6.04k

15k

0.25%

R13

1.5k

150k

0.1µF

15nF

Q2 D1

20µF

SYSTEM

LOAD

10µH

4.99k

R4 3.01k 1%

R5 3.01k 1%

RSENSE

0.025Ω

RCL

0.02Ω

20µF

0.0047µF

4008 F10

2N7002

28.7k

CHARGE

R26

150k

Li-Ion

BATTERY

D1: MBRS130T3

D2: SBM540

Q1: Si4431BDY

Q2: FDC645N

Q4: Si7423DN

Z1 VALUE SIZED FOR ABSOLUTE MAXIMUM ADAPTER VOLTAGE

Figure10. Typical LTC4008-1 Application (12.3V/4A)

LTC4008

Rev C

For more information www.analog.com

APPLICATIONS INFORMATION

PCB Layout Considerations

For maximum efficiency, the switch node rise and fall

times should be minimized. To prevent magnetic and

electrical field radiation and high frequency resonant

problems, proper layout of the components connected

to the IC is essential. (See Figure11.) Here is a PCB layout

priority list for proper layout. Layout the PCB using this

specific order.

1. Input capacitors need to be placed as close as pos-

sible to switching FET’s supply and ground connec-

tions. Shortest copper trace connections possible.

These parts must be on the same layer of copper. Vias

must not be used to make this connection.

2. The control IC needs to be close to the switching

FET ’s gate terminals. Keep the gate drive signals short

for a clean FET drive. This includes IC supply pins that

connect to the switching FET source pins. The IC can

be placed on the opposite side of the PCB relative to

above.

3. Place inductor input as close as possible to switching

FET’s output connection. Minimize the surface area of

this trace. Make the trace width the minimum amount

needed to support current—no copper fills or pours.

Avoid running the connection using multiple layers in

parallel. Minimize capacitance from this node to any

other trace or plane.

4. Place the output current sense resistor right next to

the inductor output but oriented such that the IC’s cur-

rent sense feedback traces going to resistor are not

long. The feedback traces need to be routed together

as a single pair on the same layer at any given time

with smallest trace spacing possible. Locate any filter

component on these traces next to the IC and not at

the sense resistor location.

5. Place output capacitors next to the sense resistor

output and ground.

6. Output capacitor ground connections need to feed

into same copper that connects to the input capacitor

ground before tying back into system ground.

7. Connection of switching ground to system ground or

internal ground plane should be single point. If the

system has an internal system ground plane, a good

way to do this is to cluster vias into a single star point

to make the connection.

8. Route analog ground as a trace tied back to IC ground

(analog ground pin if present) before connecting to

any other ground. Avoid using the system ground

plane. CAD trick: make analog ground a separate

ground net and use a 0Ω resistor to tie analog ground

to system ground.

9. A good rule of thumb for via count for a given high

current path is to use 0.5A per via. Be consistent.

10. If possible, place all the parts listed above on the same

PCB layer.

11. Copper fills or pours are good for all power connec-

tions except as noted above in Rule 3. You can also

use copper planes on multiple layers in parallel too—

this helps with thermal management and lower trace

inductance improving EMI performance further.

12. For best current programming accuracy provide a

Kelvin connection from RSENSE to CSP and BAT. See

Figure12 as an example.

It is important to keep the parasitic capacitance on the R

CSP and BAT pins to a minimum. The traces connecting

these pins to their respective resistors should be as short

as possible.

LTC4008

Rev C

For more information www.analog.com

PACKAGE DESCRIPTION

GN Package

20-Lead Plastic SSOP (Narrow .150 Inch)

(Reference LTC DWG # 05-08-1641)

.337 – .344*

(8.560 – 8.738)

GN20 (SSOP) 0204

1 2 345678 9 10

.229 – .244

(5.817 – 6.198)

.150 – .157**

(3.810 – 3.988)

1617181920 15 14 13 12 11

.016 – .050

(0.406 – 1.270)

.015 ± .004

(0.38 ± 0.10) × 45°

0° – 8° TYP

.0075 – .0098

(0.19 – 0.25)

.0532 – .0688

(1.35 – 1.75)

.008 – .012

(0.203 – 0.305)

TYP

.004 – .0098

(0.102 – 0.249)

.0250

(0.635)

BSC

.058

(1.473)

REF

.254 MIN

RECOMMENDED SOLDER PAD LAYOUT

.150 – .165

.0250 BSC.0165 ±.0015

.045 ±.005

* DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH

SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE

** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD

FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE

INCHES

(MILLIMETERS)

NOTE:

1. CONTROLLING DIMENSION: INCHES

2. DIMENSIONS ARE IN

3. DRAWING NOT TO SCALE

APPLICATIONS INFORMATION

4008 F11

VBAT

VIN

HIGH

FREQUENCY

CIRCULATING

PATH

BAT

SWITCH NODE

C2 C3

Figure11. High Speed Switching Path

CSP

4008 F12

DIRECTION OF CHARGING CURRENT

RSENSE

BAT

Figure12. Kelvin Sensing of Charging Current

LTC4008

Rev C

For more information www.analog.com

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog

Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications

subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

REVISION HISTORY

REV DATE DESCRIPTION PAGE NUMBER

B 7/10 Updated Figure5 and Figure6. 13, 14

C 4/18 Changed LTC4008 pin configuration and lowered TJMAX and θJA values 2

(Revision history begins at Rev B)

LTC4008

Rev C

For more information www.analog.com

 ANALOG DEVICES, INC. 2003-2018

D16841-0-4/18(C)

www.analog.com

RELATED PARTS

TYPICAL APPLICATION

NiMH/4A Battery Charger

BATMON

VFB

ICL

ACP/SHDN

FAULT

FLAG

NTC

ITH

GND

ICL

ACP

FAULT

FLAG

DCIN

INFET

CLP

CLN

TGATE

BGATE

PGND

CSP

BAT

PROG

LTC4008

6.04k

13.3k

0.25%

150k

0.12µF

THERMISTOR

10k

NTC

0.47µF

R12

100k

147k

0.25%

R10 32.4k 1%

R11

100k

VLOGIC

DCIN

0V TO 20V C1

0.1µF

INPUT SWITCH

0.1µF

Q2 D1

20µF L1

10µH

R1 4.99k 1%

R4 3.01k 1%

R5 3.01k 1%

RSENSE

0.025Ω

RCL

0.02Ω

20µF

NiMH

BATTERY

PACK

CHARGING

CURRENT

MONITOR

SYSTEM

LOAD

26.7k

0.0047µF D1: MBRS130T3

Q1: Si4431BDY

Q2: FDC645N

4008 TA02

PART NUMBER DESCRIPTION COMMENTS

LT®1511 3A Constant-Current/Constant-Voltage Battery Charger High Efficiency, Minimum External Components to Fast Charge Lithium,

NIMH and NiCd Batteries

LT1513 Sepic Constant- or Programmable-Current/Constant-

Voltage Battery Charger

Charger Input Voltage May be Higher, Equal to or Lower Than Battery Voltage,

500kHz Switching Frequency

LT1571 1.5A Switching Charger 1- or 2-Cell Li-Ion, 500kHz or 200kHz Switching Frequency, Termination Flag

LTC1628-PG 2-Phase, Dual Synchronous Step-Down Controller Minimizes CIN and COUT

, Power Good Output, 3.5V ≤ VIN ≤ 36V

LTC1709 Family 2-Phase, Dual Synchronous Step-Down Controller

with VID

Up to 42A Output, Minimum CIN and COUT

, Uses Smallest Components for

Intel and AMD Processors

LTC1729 Li-Ion Battery Charger Termination Controller Trickle Charge Preconditioning, Temperature Charge Qualification, Time or

Charge Current Termination, Automatic Charger and Battery Detection, and

Status Output

LT1769 2A Switching Battery Charger Constant-Current/Constant-Voltage Switching Regulator, Input Current

Limiting Maximizes Charge Current

LTC1778 Wide Operating Range, No RSENSE™ Synchronous

Step-Down Controller

2% to 90% Duty Cycle at 200kHz, Stable with Ceramic COUT

LTC1960 Dual Battery Charger/Selector with SPI Interface Simultaneous Charge or Discharge of Two Batteries, DAC Programmable

Current and Voltage, Input Current Limiting Maximizes Charge Current

LTC3711 No RSENSE Synchronous Step-Down Controller

with VID

3.5V ≤ VIN ≤ 36V, 0.925V ≤ VOUT ≤ 2V, for Transmeta, AMD and Intel Mobile

Processors

LTC4006 Small, High Efficiency, Fixed Voltage, Lithium-Ion

Battery Charger with Termination

Complete Charger for 3- or 4-Cell Li-Ion Batteries, AC Adapter Current Limit

and Thermistor Sensor, 16-Pin Narrow SSOP Package

LTC4007 High Efficiency, Programmable Voltage

Battery Charger with Termination

Complete Charger for 3- or 4-Cell Li-Ion Batteries, AC Adapter Current Limit,

Thermistor Sensor and Indicator Outputs

LTC4100 Smart Battery Charger Controller SMBus Rev 1.1 Compliant