NEW Series SHDC Output to 60A, 200 Vdc High Industrial Performance (HIPpak) DC Solid-State Relays FEATURES/BENEFITS * Latest generation MOSFET technology * Ultra low on-state resistance * Low output leakage current * Built-in overvoltage protection * Reverse protected triggered control input to avoid linear control risks * No radiated or conducted disturbances * IP20 touch-proof flaps IP20 touch-proof flaps Part Number Description SH10DC40 40A, 100 Vdc Solid-State Relay SH10DC40-16 40A, 60 Vdc Solid-State Relay SH20DC20-16 20A, 200 Vdc Solid-State Relay SH20DC40-16 40A, 200 Vdc Solid-State Relay SH75DC60-16 60A, 75 Vdc Solid-State Relay MECHANICAL SPECIFICATION 0.12 (3) 0.64 (16.3) 1.77 (45) max Part Number Explanation -16 Switch Type2 Option3 Output Current - Amps Line Voltage 1 NOTES 1) Line Voltage (peak): 10 = 100 Vdc 2) Switch Type: DC = DC 3) Option: Internal Voltage Protection INPUT (CONTROL) SPECIFICATIONS Control Range Must Turn-Off Voltage Min Max Units 3.5 32 Vdc 1 32 3/A1+ 1.00 (25.4) M4 Dimensions in inches (mm) Weight: 2.82 oz. (80g) Figure 1 Vdc Reverse Voltage 1+ 4/A2- 0.28 (7) ELECTRICAL SPECIFICATIONS (+25C ambient temperature unless otherwise specified) 2- 0.20(5.2) 40 1.87 (47.6) Series DC 1.70 (43.2) 10 O4.7 1.10 (28) M5 2.30 (58.5) max SH 0.29 (30) max Vdc CONTROL CHARACTERISTIC 50 @-35C 45 @25C 35 30 BLOCK DIAGRAM @100C 25 1+ +3 MOSFET |Scst 15 10 5 Driver OUTPUT 20 CONTROL Control Current (mAdc) 40 PHV 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 2- -4 Control Voltage (V) *Included with -16 option Figure 2 (c) 2010 TELEDYNE RELAYS Figure 3 (800) 284-7007 * www.teledynerelays.com SHDC Page 1 SHDC\012010\Q1 NEW Series SHDC Output to 60A, 200 Vdc High Industrial Performance (HIPpak) DC Solid-State Relays ELECTRICAL SPECIFICATIONS (+25C ambient temperature unless otherwise specified) ELECTRICAL SPECIFICATIONS (continued) (+25C ambient temperature unless otherwise specified) OUTPUT (LOAD) SPECIFICATIONS OUTPUT (LOAD) SPECIFICATIONS Min Max Units Min Max Units SH10DC40 5 100 Vdc SH10 0.7 nF SH10DC40-16 5 60 Vdc SH20DC20-16 0.6 nF SH20DC20-16 5 110 Vdc SH20DC40-16 1.1 nF SH20DC40-16 5 110 Vdc SH75DC60-16 1.5 nF SH75DC60-16 5 40 Vdc Output Capacitance (Typical) Operating Range Peak Voltage Junction-Case Thermal Resistance SH10 0.9 C/W SH10DC40 100 Vdc SH20DC20-16 1.2 C/W SH10DC40-16 100 Vdc SH20DC40-16 0.7 C/W SH20DC20-16 200 Vdc SH75DC60-16 1.2 C/W SH20DC40-16 200 Vdc SH75DC60-16 75 Vdc Built-In Heat Sink Thermal Resistance (Vertically Mounted) 10 C/W Heat Sink Thermal Time Constant 10 min Control Inputs/Power Outputs Insulation Voltage 2.5 kV Turn-On Time 20 s Turn-On Delay 20 s Turn-Off Time 20 s Turn-Off Delay 20 s 1000* Hz Overvoltage Protection (Built-In) SH10DC40-16 SH20DCXX-16 SH75DC60-16 1 56V (TVS) 75V (MOV Size 20)2 39V (TVS)1 1) Transient Voltage Supressor; 2) Metal Oxide Varistor Reverse Voltage Drop SH10DC40-16 SH20DCXX-16 1.3 1.5 V V SH75DC60-16 0.92 V SH10 40 A SH20DC20-16 20 A SH20DC40-16 SH75DC60-16 40 60 A A Nominal Current (Resistive) On-Off Frequency *For high frequency, take two times the load current to calculate the heat sink. TIME DIAGRAMS TURN-ON Non-Repetitive Peak Overload Current SH10 320 A SH20DC20-16 160 A SH20DC40-16 380 A SH75DC60-16 750 A 3 mA Leakage Current Vc (control) t Vt (switch) t tdon On-State Resistance (@ 25C) ton TURN-OFF @25 C @125 C SH10 15 30 m SH20DC20-16 45 90 m SH20DC40-16 23 46 m SH75DC60-16 4.5 8.2 m Vc (control) t Vt (switch) t tdoff toff Figure 4 SHDC Page 2 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE (c) 2010 TELEDYNE RELAYS SHDC\012010\Q1 NEW Series SHDC Output to 60A, 200 Vdc High Industrial Performance (HIPpak) DC Solid-State Relays BUILT IN OVERVOLTAGE PROTECTION CHARACTERISTICS Uto < Utp t max = 0.75 (Uto - Ut max) x Ie P ( protection ) = 1W max Ielk : Ie : Utp : Utmax : (Uto - Ut max) x Ie x t 1 T Uto Utn t T Leakage current of relay User load nominal current Relay max. non repetitive peak voltage Max. nominal voltage of relay : : : : Possible overvoltage above Utmax User power supply voltage Overvoltage duration Time between 2 overvoltages SH20DC20-16 & SH20DC40-16 Ielk / Ie 1 0.8 0.6 0.4 0.2 0 0 10 20 30 40 50 60 U t max ( =U emax) 70 80 90 100 Ut (V) Utp Leakage Current (A) Leakage Current (A) SH10DC40-16 Ielk / Ie 1 0.8 0.6 0.4 0.2 0 0 20 40 Voltage (Vdc) 60 80 100 120 140 160 180 200 Ut (V) U t max ( =U emax) Utp Voltage (Vdc) Figure 5b Figure 5a Leakage Current (A) SH75DC-16 Ielk / Ie 1 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 Ut (V) U t max ( =U emax) Utp Voltage (Vdc) Figure 5c (c) 2010 TELEDYNE RELAYS (800) 284-7007 * www.teledynerelays.com SHDC Page 3 SHDC\012010\Q1 NEW Series SHDC Output to 60A, 200 Vdc High Industrial Performance (HIPpak) DC Solid-State Relays HIGH SIDE WIRING DIAGRAM (Load Connected to "--") GENERAL SPECIFICATIONS (+25C ambient temperature unless otherwise specified) ENVIRONMENTAL SPECIFICATIONS DC Control Power Supply DC Mains Ve Min 1+ C1 3/A1+ Ie Vt (Red paths as short as possible) 4/A2- Vc 2- D2 Ic Units Operating Temperature -25 +90 C Storage Temperature -40 +100 C 2.5 kV Input-Output Isolation On-Off Control Max Insulation Resistance 1 G Insulation Capacitance 8 pF Junction Temperature Steady State 125 C Transient 175 C Case Temperature 100 C Load CONNECTIONS Figure 6a Power LOW SIDE WIRING DIAGRAM (Load Connected to "+") POZIDRIV2 Tightening Torque DC Control Power Supply DC Mains Ve Ie 2- 4/A2- 1+ 3/A1+ D2 1.2 N.m M5 M4 MISCELLANEOUS (Red paths as short as possible) Vt 2 N.m Insulated crimp terminals (Round Tabs, Eyelet Type) C1 Vc Ic Screwdriver Display Green LED (ON) Housing UL94V0 Mounting 2 screws (M4x12mm) Noise Level On-Off Control Control No audible noise GENERAL Standards Load Figure 6b IEC60947-1 Protection Level IP20 Protection Against Direct Touch Yes CE Marking Yes E.M.C. EMISSION Radiated & Conducted DisturbancesPending ACCESSORIES Faston: Contact Factory NOTES 1. For additional/custom options, contact factory. SHDC Page 4 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE (c) 2010 TELEDYNE RELAYS SHDC\012010\Q1 NEW Series SHDC Output to 60A, 200 Vdc High Industrial Performance (HIPpak) DC Solid-State Relays OUTPUT RELAY CHARACTERISTIC CURVES FOR SH10DC40 & SH10DC40-16 60.8 45 0.9C/W 1.1C/W 0.75C/W 0.3C/W 0.55C/W 40 48 35 36.8 30 27 25 18.8 20 12 15 6.75 10 3 5 Power Dissipation (W) Load Current (A) 1.2C/W 0.75 4C/W 10C/W 2.1C/W 2.2C/W 0 0 10 20 30 40 50 60 70 80 90 100 0 110 Ambient Temperature (C) t1 * D (% ) = x 100 (c) t2 ON-State Peak Overload Current (Apk) Figure 7a 360 Non-repetitive D=1% (Tc=100C, Tjmax=175C) 320 280 Repetitive D=5% (Tc=100C, Tjmax=175C) 240 Repetitive D=10% (Tc=100C, Tjmax=175C) 200 Repetitive D=20% (Tc=100C, Tjmax=175C) 160 120 80 40 Repetitive D=50% (Tc=100C, Tjmax=125C) 0 0.1 1 10 100 1000 Pulse Duration (S) Figure 7b ON Resistance (m) 30 25 20 15 10 5 0 -50 0 50 100 150 Junction Temperature (C) Figure 7c (c) 2010 TELEDYNE RELAYS (800) 284-7007 * www.teledynerelays.com SHDC Page 5 SHDC\012010\Q1 NEW Series SHDC Output to 60A, 200 Vdc High Industrial Performance (HIPpak) DC Solid-State Relays OUTPUT RELAY CHARACTERISTIC CURVES FOR SH20DC20-16 56.25 25 10C/W 2.2C/W 4C/W 2.1C/W 1.2C/W 0.9C/W 1.1C/W Load Current (A) 20.25 15 0.75C/W 0.55C/W 0.3C/W 9 10 5 Power Dissipation (W) 36 20 2.25 0 0 10 20 30 40 50 60 70 80 90 100 0 110 Ambient Temperature (C) t1 * D (% ) = x 100 (c) t2 ON-State Peak Overload Current (Apk) Figure 8a 180 Non-repetitive D=1% (Tc=100C, Tjmax=175C) 160 140 Repetitive D=5% (Tc=100C, Tjmax=175C) 120 Repetitive D=10% (Tc=100C, Tjmax=175C) 100 Repetitive D=20% (Tc=100C, Tjmax=175C) 80 60 40 Repetitive D=50% (Tc=100C, Tjmax=125C) 20 0 0.1 1 10 100 1000 Pulse Duration (S) Figure 8b ON Resistance (m) 120 100 80 60 40 20 0 -50 0 50 100 150 Junction Temperature (C) Figure 8c SHDC Page 6 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE (c) 2010 TELEDYNE RELAYS SHDC\012010\Q1 NEW Series SHDC Output to 60A, 200 Vdc High Industrial Performance (HIPpak) DC Solid-State Relays OUTPUT RELAY CHARACTERISTIC CURVES FOR SH20DC40-16 97.8 45 Load Current (A) 0.9C/W 0.75C/W 0.55C/W 0.3C/W 40 77.3 35 59.2 30 43.5 25 30.2 20 19.3 15 10.9 10 4.8 5 Power Dissipation (W) 1.1C/W 1.2C/W 1.2 4C/W 8C/W 2.2C/W 2.1C/W 0 0 10 20 30 40 50 60 70 80 90 100 0 110 Ambient Temperature (C) t1 * D (% ) = x 100 (c) t2 ON-State Peak Overload Current (Apk) Figure 9a 320 Non-repetitive D=1% (Tc=100C, Tjmax=175C) 280 Repetitive D=5% (Tc=100C, Tjmax=175C) 240 Repetitive D=10% (Tc=100C, Tjmax=175C) 200 160 Repetitive D=20% (Tc=100C, Tjmax=175C) 120 80 40 Repetitive D=50% (Tc=100C, Tjmax=125C) 0 0.1 1 10 100 1000 Pulse Duration (S) Figure 9b ON Resistance (m) 60 50 40 30 20 10 0 -50 0 50 100 150 Junction Temperature (C) Figure 9c (c) 2010 TELEDYNE RELAYS (800) 284-7007 * www.teledynerelays.com SHDC Page 7 SHDC\012010\Q1 NEW Series SHDC Output to 60A, 200 Vdc High Industrial Performance (HIPpak) DC Solid-State Relays OUTPUT RELAY CHARACTERISTIC CURVES FOR SH75DC60-16 65 34.8 0.75C/W 60 29.7 24.9 Load Current (A) 50 0.55C/W 45 0.3C/W 40 20.6 16.7 13.2 35 10.1 30 7.42 25 5.15 20 3.3 15 1.85 10 0.82 5 10C/W 0 0 10 20 4C/W 30 2.2C/W 40 2.1C/W 50 1.2C/W 60 1.1C/W 70 0.21 0.9C/W 80 Power Dissipation (W) 55 0 90 100 110 Figure 10a 800 700 1000 Non-repetitive D=1% (Tc=100C, Tjm ax=175C) Repetitive D=5% (Tc=100C, Tjm ax=175C) 600 Reverse Current (A) ON-State Peak Overload Current (Apk) Ambient Temperature (C) Repetitive D=10% (Tc=100C, Tjm ax=175C) 500 Repetitive D=20% (Tc=100C, Tjm ax=175C) 400 300 200 100 0.001 0.01 Uc=0 ; Tj=125C 10 1 0.1 0 1 0,5 1 1,5 2 2,5 3 Reverse Voltage Drop (V) Pulse Duration (S) Figure 10c Figure 10b 0.35 12 0.3 10 ON Resistance (m) Power Element Transient Thermal Impedance Uc0 ; Tj=125C 0.1 Repetitive D=50%(Tc=100C, Tjm ax=125C) 0 0.0001 100 0.25 D=50% 0.2 D=20% D=10% 0.15 D=5% 0.1 D=2% D=1% 0.05 Single pulse 0 0.0001 SHDC Page 8 0.001 0.01 0.1 8 6 4 2 0 -50 0 50 100 150 1 Pulse Duration (S) Junction Temperature (C) Figure 10d Figure 10e SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE (c) 2010 TELEDYNE RELAYS SHDC\012010\Q1