April 2018
EMC Components
For power line
MPZ1608 1608[0603 inch]*
* Dimensions codeJIS[EIA]
Chip beads
MPZ1608
type
MPZ series
(2/11)
20180413 / beads_commercial_power_mpz1608_en.fm
EMC Components
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40°C, humidity:10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equip-
ment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equip-
ment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or qual-
ity require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society,
person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment  
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing pro-
tection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/11)
20180413 / beads_commercial_power_mpz1608_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
Chip beads
For power line
FEATURES
Noise reduction solution for power line.
Compared to the MMZ series, has low direct current resistance for compatibility with large currents, optimal for low power consumption.
Various frequency characteristics with 5 materials of different features for countermeasures against everything from general signals to
high-speed signals.
Performs well even in signal lines where low direct current resistance is required.
APPLICATION
Noise removal for mobile devices such as smartphones and tablet terminals, and various modules.
Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment.
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The storage temperature range is for after the circuit board is mounted.
Overview of MPZ1608 type
MPZ 1608 B 471 A T A00
Series name L×W×T dimensions Material name Impedance Characteristic
type Packaging style Internal code
(mm) () at 100MHz
1608 1.6×0.8x0.6 S 260 26 A T Taping A00
1.6×0.8x0.8 Y 471 470 B AH0
B
R
D
Type
Temperature ranges Package quantity Individual weight
Operating
temperature
（°C）
Storage
temperature
（°C）(pieces/reel) （mg）
MPZ1608 t=0.6mm –55 to +125 –55 to +125 4,000 3
t=0.8mm –55 to +125 –55 to +125 4,000 4
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html
Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/11)
20180413 / beads_commercial_power_mpz1608_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MPZ1608 type
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/11)
20180413 / beads_commercial_power_mpz1608_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MPZ1608 type
MATERIAL CHARACTERISTIC
B material: This type is perfectly suited for fast digital signals. By equalizing R components and X components that beads possess at a
frequency of 5MHz, it is able to suppress overshooting, undershooting and ringing of fast digital signals.
R material: For wide frequency applications calling for broad impedance characteristics. For digital signal line applications calling
requiring good waveform integrity. Impedance values selected for effectiveness at 10 to 200MHz.
S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in
which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz.
Y material: High frequency range type intended for the 100MHz region and above. For signal line applications in which the signal
frequency is far from the cutoff frequency. Impedance values selected for effectiveness at 80 to 400MHz.
D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies.
Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications.
TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS 
0
500
1000
1500
2000
2500
10 100 1000
Frequency(MHz)
Impedance(Ω)
RS
D
Y
B
(6/11)
20180413 / beads_commercial_power_mpz1608_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MPZ1608 type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Thickness(T)
0.6±0.15mm
0.8±0.15mm
0.8±0.15
1.6±0.15
0.3±0.2
T
Dimensions in mm
0.80.6 0.6
0.8
(7/11)
20180413 / beads_commercial_power_mpz1608_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MPZ1608 type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Please refer to the graph of rated current vs. temperature characteristics (derating) about the rating current at 85°C or more in temperature of the product.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
○ Rated current vs. temperature characteristics (derating)
Impedance DC resistance Rated currentThickness T Part No.
[100MHz]
()Tolerance ()max. (A)max. (mm)
470 ±25% 0.150 1.0 0.8 MPZ1608B471ATA00
26 ±25% 0.007 6.0 0.6 MPZ1608S260ATAH0
30 ±100.010 5.0 0.6 MPZ1608S300ATAH0
60 ±25% 0.020 3.5 0.6 MPZ1608S600ATAH0
100 ±25% 0.030 3.0 0.6 MPZ1608S101ATAH0
120 ±25% 0.045 2.0 0.6 MPZ1608S121ATAH0
180 ±25% 0.050 2.0 0.6 MPZ1608S181ATAH0
220 ±25% 0.050 2.2 0.8 MPZ1608S221ATA00
330 ±25% 0.080 1.7 0.8 MPZ1608S331ATA00
470 ±25% 0.150 1.0 0.8 MPZ1608S471ATA00
600 ±25% 0.150 1.0 0.8 MPZ1608S601ATA00
1000 ±25% 0.300 0.8 0.8 MPZ1608S102ATA00
390 ±25% 0.120 1.2 0.8 MPZ1608R391ATA00
60 ±25% 0.030 2.3 0.8 MPZ1608Y600BTA00
100 ±25% 0.040 2.0 0.8 MPZ1608Y101BTA00
150 ±25% 0.050 1.8 0.8 MPZ1608Y151BTA00
220 ±25% 0.100 1.5 0.8 MPZ1608Y221BTA00
30 ±100.060 1.8 0.8 MPZ1608D300BTA00
60 ±25% 0.100 1.2 0.8 MPZ1608D600BTA00
100 ±25% 0.150 1.0 0.8 MPZ1608D101BTA00
Measurement item Product No. Manufacturer
Impedance E4991A+16192A Keysight Technologies
DC resistance Type-7556 Yokogawa
0
1
2
3
4
5
7
6
–55 –35 –15 5 25 45 65 85 105 125
Temperature (°C)
Rated current (A)
S600A S101AS300AS260A
S102A
B471A,S471A,S601A,D101BR391A,D600B
Y221BS331A
Y151B,D300B
Y600B S221A S121A,S181A,Y101B
(8/11)
20180413 / beads_commercial_power_mpz1608_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MPZ1608 type
ELECTRICAL CHARACTERISTICS
Z VS. FREQUENCY CHARACTERISTICS (BY SERIES)
MPZ1608B series MPZ1608S series MPZ1608R series
MPZ1608Y series MPZ1608D series
100001000100101
Frequency (MHz)
Impedance (Ω)
0
100
200
300
400
500 MPZ1608B471A
0
1000
1200
800
900
700
600
500
400
300
200
100
100001000100101
Frequency (MHz)
Impedance (Ω)
MPZ1608S102A
MPZ1608S300A
MPZ1608S600A
MPZ1608S260A
MPZ1608S101A
MPZ1608S121A
MPZ1608S181A
MPZ1608S221A
MPZ1608S331A
MPZ1608S471A
MPZ1608S601A
400
300
200
100
0
500
100001000100101
Frequency (MHz)
Impedance (Ω)
MPZ1608R391A
0
50
100
150
200
250
300
350
100001000100101
Frequency (MHz)
Impedance (Ω)
MPZ1608Y221B
MPZ1608Y600B
MPZ1608Y151B
MPZ1608Y101B
0
100
200
300
400
500
600
100001000100101
Frequency (MHz)
Impedance (Ω)
MPZ1608D101B
MPZ1608D600B
MPZ1608D300B
(9/11)
20180413 / beads_commercial_power_mpz1608_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MPZ1608 type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
MPZ1608B471ATA00 MPZ1608S260ATAH0 MPZ1608S300ATAH0
MPZ1608S600ATAH0 MPZ1608S101ATAH0 MPZ1608S121ATAH0
MPZ1608S181ATAH0 MPZ1608S221ATA00 MPZ1608S331ATA00
MPZ1608S471ATA00 MPZ1608S601ATA00 MPZ1608S102ATA00
MPZ1608R391ATA00 MPZ1608Y600BTA00 MPZ1608Y101BTA00
1 10 100 1000 10000
0
5
10
15
20
25
30
35
40
Frequency (MHz)
Impedance (Ω)
Z
R
X
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
0
100
200
300
400
500
Z
R
X
1 10 100 1000 10000
0
5
10
15
20
25
30
35
40
Frequency (MHz)
Impedance (Ω)
ZR
X
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
Z
R
X
0
20
40
60
80
100
120
140
160
ZR
X
0
50
100
150
200
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
100
80
60
40
20
01 10 100 1000 10000
Z
X
R
Frequency (MHz)
Impedance (Ω)
300
100
50
150
200
250
01 10 100 1000 10000
ZR
X
Frequency (MHz)
Impedance (Ω)
1 10 100 1000 10000
R
X
Z
0
50
100
150
200
250
300
350
400
450
Frequency (MHz)
Impedance (Ω)
Z
R
X
0
50
100
150
200
300
250
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
800
700
600
500
400
300
200
100
01 10 100 1000 10000
Z
R
X
Frequency (MHz)
Impedance (Ω)
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
0
200
400
600
800
1000
1200
ZR
X
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
ZR
X
0
100
200
300
400
500
600
700
1 10 100 1000 10000
0
20
40
60
80
100
120
140
Frequency (MHz)
Impedance (Ω)
R
X
Z
0
50
100
150
200
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
R
X
Z
500
400
300
200
100
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
R
X
Z
(10/11)
20180413 / beads_commercial_power_mpz1608_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MPZ1608 type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
MPZ1608Y151BTA00 MPZ1608Y221BTA00 MPZ1608D300BTA00
MPZ1608D600BTA00 MPZ1608D101BTA00
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
0
Z
R
X
50
100
150
200
250
300
350
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
R
X
Z
0
50
100
150
200
250
300
250
200
150
100
50
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
R
X
Z
1 10 100 1000 10000
0
100
200
300
400
500
600
Frequency (MHz)
Impedance (Ω)
RX
Z
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
R
X
Z
50
0
100
150
200
250
300
350
(11/11)
20180413 / beads_commercial_power_mpz1608_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MPZ1608 type
PACKAGING STYLE
REEL DIMENSIONS
TAPE DIMENSIONS
Dimensions in mm
Ty p e ABK
MPZ1608 1.1±0.2 1.9±0.2 1.1max.
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
Dimensions in mm
1.0
ø60min.
14.4max.
8.4 +2.0
–0.0
B
A
8.0±0.3
3.5±0.05
1.75±0.1
4.0±0.1
4.0±0.1
2.0±0.05
1.5 +0.1
0
K
160min. Taping 200min.
300min.
Drawing direction
Dimensions in mm