PACKING 81mg;120pcs/10.72Kg
DC VOLTAGE
SPECIFICATION
MODEL
OUTPUT
RATED CURRENT
CURRENT RANGE
RATED POWER
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
LINE REGULATION
LOAD REGULATION
VOLTAGE RANGE
SETUP, RISE, HOLD UP TIME
EFFICIENCY(Typ.)
DC CURRENT(Typ.)
OVER LOAD
OVER VOLTAGE
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
DIMENSION
INPUT
PROTECTION
ENVIRONMENT
SAFETY &
EMC
OTHERS
NOTE
12V
1.25A
0 ~ 1.25A
15W
100mVp-p
1.0%
1.0%
2.5s, 25ms, ----/12VDC/24VDC/48VDC at full load
A: 9.2 ~18VDC (12VDC) B:18 ~ 36VDC (24VDC) C:36~72VDC(48VDC)
74%
1.9A/12VDC 0.9A/24VDC 0.45A/48VDC
105% -150% rated output power
Protection type : hiccup mode ,recovery automatically after fault condition is removed
5.75 ~ 6.75V
20 ~ 95% RH non-condensing
10 ~ 500Hz, 2G 10min./1cycle, Period for 60min.each along X, Y, Z axes
I/P-O/P:1.5KVAC
I/P-O/P:100M Ohms/500VDC / 25 / 70% RH℃
94*49*25mm (L*W*H)
Protections:Short circuit/Over load /Over voltage/Polarity
Cooling by free air convection
100% full load burn-in test
Low cost
High reliability
2 year warranty
15W DC-DC Single Output Switching Power Supply PSD-15series
20 ~ 90% RH non-condensing-10
1.All parameters NOT specially mentioned are measured at normal input,rated load and 25 of ambient temperature.
2.Ripple & noise are measued at 20 MHz of bandwidth by using a 12inch twisted pair-wire termined with a 0.1uf & 47uf capacitor.
3.Tolerance:includes set up tolerance,line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed
that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power
supplies.
(as available on http://www.meanwell.com)
2.0%
60
PSD-15C-12
5V
3A
0 ~ 3A
15W
50mVp-p
1.0%
1.0%
2.0%
24V
0.6A
0 ~ 0.6A
14.4W
100mVp-p
0.5%
0.5%
2.0%
67% 72%
13.8~ 16.2V 27.6 ~ 32.4V
EMI CONDUCTION&RADIATION Compliance to EN55022(CISPR22) CLASS B
PSD-15A-24
PSD-15A-12 PSD-15B-12 PSD-15B-24 PSD-15C-24
PSD-15C-05
PSD-15B-05
PSD-15A-05
78% 78% 78% 78% 78% 79%
EMS IMMUNITY Compliance to EN61000-4-2, 3, 4, 6, 8 EN55024, EN61000-6-1 Light industry level, criteria A
Protection type : Shut off o/p voltage, clamping by zener diode
MTBF 740.4Khrs min. MIL-HDBK-217F(25 )℃
File Name:PSD-15-SPEC 2015-05-29
â– Features :
Unit:mm
LOAD (%)
(HORIZONTAL)
(VERTICAL)
Mechanical Specification
Output Derating
-10
-10
01020304050
45
60
55
20
40
60
80
100
Mounting Holes
4-3.5 Dia
3.5 87
94
49
42
3.5
25
CN2
2
1
DC Output Connector (CN2) : JST B2P-VH or equivalent
Pin No.
1
2
Assignment
-V
+V
Mating Housing
or equivalent
Terminal
or equivalent
DC Input Connector (CN1) : JST B3P-VH or equivalent
Pin No.
1
2
3
Assignment
-V
No Pin
+V
Mating Housing
or equivalent or equivalent
Terminal
PWM
CIRCUIT
DETECTION
EMI
FILTER
POWER
SWITCH-
FILTER
&
RECTIFIERS +V
-V
I/P
ING
CONTROL
Block Diagram fosc : 100KHz
15W DC-DC Single Output Switching Power Supply PSD-15series
CN1
1
2
3
7.5 4426
4
AMBIENT TEMPERATURE ( )
OLP
JST VHR JST SVH-21T-P1.1 JST VHR JST SVH-21T-P1.1
2 max.
File Name:PSD-15-SPEC 2015-05-29
