zSFP+ Multi-Port Connector Tooling
Doc. No: ATS-622025280 Release Date: 09-13-13
UNCONTROLLED COPY
Page 1 of 2
Revision: C Revision Date: 06-05-17
zSFP+
CAGE
ASSEMBLY
PCB
2mm
MINIMUM
(BOTH SIDES)
KEEP OUT
ZONE
Figure 1
5mm
MINIMUM
2-by-12
zSFP+
Insertion Tool
Application Tooling
Specification Sheet
Order No. 62202-5280
FEATURES
Lightweight tool used in the insertion of a zSFP+ connector in a PCB
Inserts connector to a PCB without damage to the board
Use tool 62202-5290 for removing connectors
PCB support not included (furnished by customer)
SCOPE
Products: zQuad Small Form-Factor Pluggable Plus (zSFP+) Cage Assembly, with Elastomeric Gasket or Metal
EMI Gasket, 2-by-12 Enhanced EMI Cage Construction.
Connector Series No.
Connector Order No.
170071
170071
-
1201
170071
-
1211
170071
-
1212
170071
-
1213
170071
-
1214
170071
-
1215
171224
171224
-
1201
171224
-
1209
171224
-
1211
171224
-
1212
171224
-
1213
171224
-
1214
171224
-
1215
171224
-
1230
171224
-
1231
171224
-
1241
171224
-
1242
171224
-
1250
171224
-
1260
171224
-
1261
172501
172501
-
1202
Notes:
1. See the following pages for tooling operation instructions.
2. These tools require a “Keep Out Zone” around the connector free of components. The right and left sides
should be 0.08” (2mm). The rear of the connector should be .197” (5.0mm). See Figure 1.
zSFP+ Multi-Port Connector Tooling
Doc. No: ATS-622025280 Release Date: 09-13-13
UNCONTROLLED COPY
Page 2 of 2
Revision: C Revision Date: 06-05-17
INSERTION TOOL
(CLOSED END)
zSFP+
CONNECTOR
ASSEMBLY
Figure 2
PCB
BOTTOM OF CONNECTOR
TO SEAT FLUSH ON PCB
INSERTION TOOL
OVER CONNECTOR
ASSEMBLY
SIDE PLATE
PCB
1.0mm CLEARANCE BETWEEN
BOARD AND THE SIDE PLATE
AFTER zSFP+ ASSEMBLY IS
SEATED ONTO THE PCB Figure 3
Description
The following
Instructions are used for
inserting the 2-by-12
connector into a PCB:
Operation
1. Place a connector assembly on the PCB.
2. Place the tool on the connector assembly (closed end to the back end of the connector). See Figure 2.
3. Place tool, connector and PCB in a press of suitable size and force, and seat the connector assembly as
shown. The support plate (furnished by the customer) under the PCB must have clearance for the connector
pins as they pass through the PCB.
Clearance
Use this tool only with a press that has a predetermined shut height when seating a zSFP+ assembly on a PCB.
See Figure 3. Allowing the press-in tool to stop on the board will result in damage to the zSFP+ cage and the
terminals being overseated.
CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling.
Application Tooling Support
Phone: (402) 458-TOOL (8665)
E-Mail: applicationtooling@molex.com
Website: www.molex.com/applicationtooling
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks
listed herein belong to their respective owners.
