SPEC NO: DSAL0865 REV NO: V.2 DATE: APR/13/2011 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006792
3.5x2.8mm SURFACE MOUNT LED LAMP
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Part Number: AA3528QBS/D Blue
Features
zSingle color.
zSuitable for all SMT assembly and solder process.
zAvailable on tape and reel.
zIdeal for backlighting.
zPackage : 1500pcs / reel.
zMoisture sensitivity level : level 3.
zRoHS compliant.
Description
The Blue source color devices are made with InGaN Light
Emitting Diode.
Static electricity and surge damage the LEDS.
It is recommended to use a wrist band or anti-electrostatic
glove when handling the LEDs.
All devices, equipment and machinery must be electrically
grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4.The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAL0865 REV NO: V.2 DATE: APR/13/2011 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006792
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4.1. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diame-
ter of the nozzle should be as large as possible.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
SPEC NO: DSAL0865 REV NO: V.2 DATE: APR/13/2011 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006792
Selection Guide
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Part No. Dice Lens Type
V
iewing
Angle [1]
Min. Typ. 2θ1/2
AA3528QBS/D Blue (InGaN) Water Clear 90 150 120°
Iv (mcd) [2]
@ 20mA
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Blue 468 nm IF=20mA
λD [1] Dominant Wavelength Blue 470 nm IF=20mA
Δλ1/2 Spectral Line Half-width Blue 25 nm IF=20mA
C Capacitance Blue 100 pF VF=0V;f=1MHz
VF [2] Forward Voltage Blue 3.3 4 V IF=20mA
IR Reverse Current Blue 50 uA VR=5V
Parameter Blue Units
Power dissipation 120 mW
DC Forward Current 30 mA
Peak Forward Current [1] 150 mA
Reverse Voltage 5 V
Operating Temperature -40°C To +85°C
Storage Temperature -40°C To +85°C
SPEC NO: DSAL0865 REV NO: V.2 DATE: APR/13/2011 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006792
Blue AA3528QBS/D
SPEC NO: DSAL0865 REV NO: V.2 DATE: APR/13/2011 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006792
AA3528QBS/D
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAL0865 REV NO: V.2 DATE: APR/13/2011 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201006792
PACKING & LABEL SPECIFICATIONS AA3528QBS/D
