TFA9890A 9.5 V boosted audio system with adaptive sound maximizer and speaker protection Rev. 1 -- 16 September 2014 Product short data sheet 1. General description The TFA9890A is a high efficiency class-D audio amplifier with a sophisticated speaker boost and protection algorithm. It can deliver 7.2 W peak output power into an 8 speaker at a supply voltage of 3.6 V. The internal boost converter raises the supply voltage to 9.5 V, providing ample headroom for major improvements in sound quality. A safe working environment is provided for the speaker under all operating conditions. The TFA9890A maximizes acoustic output while ensuring diaphragm displacement and voice coil temperature do not exceed their rated limits. This function is based on a speaker box model that operates in all loudspeaker environments (e.g. free air, closed box or vented box). Furthermore, advanced signal processing ensures that the quality of the audio signal is never degraded by unwanted clipping or distortion in the amplifier or speaker. Unlike competing solutions, the adaptive sound maximizer algorithm uses feedback to accurately calculate both the temperature and the excursion, allowing the TFA9890A to adapt to changes in the acoustic environment. Internal intelligent DC-to-DC conversion boosts the supply rail to provide additional headroom and power output. The supply voltage is only raised when necessary. This maximizes the output power of the class-D audio amplifier while limiting quiescent power consumption. The TFA9890A also incorporates advanced battery protection. By limiting the supply current when the battery voltage is low, it prevents the audio system from drawing excessive load currents from the battery, which could cause a system undervoltage. The advanced processor minimizes the impact of a falling battery voltage on the audio quality by preventing distortion as the battery discharges. The device features low RF susceptibility because it has a digital input interface that is insensitive to clock jitter. The second order closed loop architecture used in a class-D audio amplifier provides excellent audio performance and high supply voltage ripple rejection. The audio input interface is I2S and the control settings are communicated via an I2C-bus interface. The device also provides the speaker with robust protection against ESD damage. In a typical application, no additional components are needed to withstand a 15 kV discharge on the speaker. The TFA9890A is available in a 49-bump WLCSP (Wafer Level Chip-Size Package) with a 400 m pitch. TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 2. Features and benefits Sophisticated speaker-boost and protection algorithm that maximizes speaker performance while protecting the speaker: Fully embedded software, no additional license fee or porting required Total integrated solution that includes DSP, amplifier, DC-to-DC, sensing and more Adaptive excursion control - guarantees that the speaker membrane excursion never exceeds its rated limit Real-time temperature protection - direct measurement ensures that voice coil temperature never exceeds its rated limit Environmentally aware - automatically adapts speaker parameters to acoustic and thermal changes including compensation for speaker-box leakage Speaker error detection (detects faulty speakers and enclosures) Output power: 3.6 W (RMS) into 8 at 3.6 V supply voltage (THD = 1 %) Clip avoidance - DSP algorithm prevents clipping even with sagging supply voltage Bandwidth extension option to increase low frequency response Compatible with standard Acoustic Echo Cancellers (AECs) High efficiency and low power dissipation Wide supply voltage range (fully operational from 2.7 V to 5.5 V) Two I2S inputs to support two audio sources I2C-bus control interface (400 kHz) Dedicated speech mode with speech activity detector Speaker current and voltage monitoring (via the I2S-bus) for Acoustic Echo Cancellation (AEC) at the host Fully short-circuit proof across the load and to the supply lines Sample frequencies from 8 kHz to 48 kHz supported 3 bit clock/word select ratios supported (32x, 48x, 64x) Option to route I2S input direct to I2S output to allow a second I2S output slave device to be used in combination with the TFA9890A TDM interface supported (with limited functionality) Volume control Low RF susceptibility Input clock jitter insensitive interface Thermally protected 15 kV system-level ESD protection without external components `Pop noise' free at all mode transitions 3. Applications TFA9890A_SDS Product short data sheet Mobile phones Tablets Portable Navigation Devices (PND) Notebooks/Netbooks MP3 players and portable media players Small audio systems All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 2 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 4. Quick reference data Table 1. Quick reference data Symbol Parameter Conditions Min Typ Max Unit VBAT battery supply voltage on pin VBAT 2.7 - 5.5 V VDDD digital supply voltage on pin VDDD 1.65 1.8 1.95 V IBAT battery supply current on pin VBAT and in DC-to-DC converter coil; Operating modes with load; DC-to-DC converter in Adaptive Boost mode (no output signal, VBAT = 3.6 V, VDDD = 1.8 V) - 4 - mA Power-down mode - 1 - A IDDD digital supply current on pin VDDD; Operating modes; SpeakerBoost Protection activated - 20 - mA on pin VDDD; Operating modes; CoolFlux DSP bypassed - 6 - mA on pin VDDD; Power-down mode; BCK1 = WS1 = DATAI1 = BCK2 = WS2 = DATAI2 = DATAI3 = 0 V - 10 - A RL = 8 ; fs = 48 kHz - 3.6 - W RL = 8 ; fs = 32 kHz - 3.7 - W Po(RMS) RMS output power THD+N = 1 %; CLIP = 0 5. Ordering information Table 2. Ordering information Type number TFA9890AUK Package Name Description Version WLCSP49 wafer level chip-size package; 49 bumps; 3.37 x 2.97 mm TFA9890AUK TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 3 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 6. Block diagram 9''' $'6 $'6 9%$7 ,1% * ) ) * ()* 7)$$ 6&/ * 6'$ ) $'$37,9( '&WR'& &219(57(5 5$0520 0(025< , & ,17(5)$&( '$7$, % ()* %67 ()* *1'% $%& 9''3 & 287$ $ 287% %% *1'3 $%& &'' ()* *1'' 5(*,67(56 '$7$, $ :6 $ , 6 ,1387 ,17(5)$&( [ %&. % 08; 63($.(53527(&7,21 $/*25,7+0$1' 92/80(&2172/ &RRO)OX['63 3:0 &/$66' $8',2 $03/,),(5 '$7$, & :6 ' %&. ( ,6(/ '$7$2 $ ,6 287387 ,17(5)$&( 08; &855(17 6(16,1* 352&(6625 ,6'2& FXUUHQWVHQVLQJ $'& 7(036(16( 567 % 3527(&7,21 273 293 893 2&3 ,'3 3// 9%$76(16( Fig 1. $ ( ' & & ' ( ,17 7(67 7(67 7(67 7(67 7(67 7(67 DDD Block diagram TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 4 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 7. Pinning information 7.1 Pinning 1 2 3 4 5 6 bump A1 index area 7 G 2 3 4 5 6 7 A F B E C D D C E B F A G bump A1 index area 010aaa782 010aaa783 a. Bottom view Fig 2. 1 b. Transparent top view Bump configuration 1 2 3 4 5 6 7 A WS1 DATAI1 DATAO INT GNDD OUTB VDDP B BCK1 GNDD DATAI3 RST GNDP GNDP VDDP C DATAI2 GNDD TEST4 TEST5 GNDD OUTA VDDP D WS2 GNDD TEST3 TEST6 GNDD n.c. n.c. E BCK2 GNDD TEST2 TEST7 GNDB INB BST F SDA ADS1 ADS2 GNDD GNDB INB BST G SCL VBAT VDDD GNDD GNDB INB BST 010aaa807 Transparent top view Fig 3. TFA9890A_SDS Product short data sheet Bump mapping All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 5 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection Table 3. TFA9890A_SDS Product short data sheet Pinning Symbol Pin Type Description WS1 A1 I digital audio word select input 1 DATAI1 A2 I digital audio data input 1 DATAO A3 O digital audio data output INT A4 O interrupt output GNDD A5 P digital ground OUTB A6 O inverting output VDDP A7 P power supply voltage BCK1 B1 I digital audio bit clock input 1 GNDD B2 P digital ground DATAI3 B3 I digital audio data input 3 RST B4 I reset input GNDP B5 P power ground GNDP B6 P power ground VDDP B7 P power supply voltage DATAI2 C1 I digital audio data input 2 GNDD C2 P digital ground TEST4 C3 O test signal input 4; for test purposes only, connect to PCB ground TEST5 C4 O test signal input 5; for test purposes only, connect to PCB ground GNDD C5 P digital ground OUTA C6 O non-inverting output VDDP C7 P power supply voltage WS2 D1 I digital audio word select input 2 GNDD D2 P digital ground TEST3 D3 O test signal input 3; for test purposes only, connect to PCB ground TEST6 D4 O test signal input 6; for test purposes only, connect to PCB ground GNDD D5 P digital ground n.c. D6 - not connected[1] n.c. D7 - not connected[1] BCK2 E1 I digital audio bit clock input 2 GNDD E2 P digital ground TEST2 E3 O test signal input 2; for test purposes only, connect to PCB ground TEST7 E4 O test signal input 7; for test purposes only, connect to PCB ground GNDB E5 P boosted ground INB E6 P DC-to-DC boost converter input BST E7 O boosted supply voltage output SDA F1 I/O I2C-bus data input/output ADS1 F2 I address select input 1 ADS2 F3 I address select input 2 GNDD F4 P digital ground GNDB F5 P boosted ground INB F6 P DC-to-DC boost converter input All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 6 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection Table 3. Symbol Pin Type Description BST F7 O boosted supply voltage output SCL G1 I I2C-bus clock input VBAT G2 P battery supply voltage sense input VDDD G3 P digital supply voltage GNDD G4 P digital ground GNDB G5 P boosted ground INB G6 P DC-to-DC boost converter input BST G7 O boosted supply voltage output [1] TFA9890A_SDS Product short data sheet Pinning ...continued Can be used to simplify routing to OUTA (see Figure 3). All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 7 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 8. Functional description The TFA9890A is a highly efficient mono Bridge Tied Load (BTL) class-D audio amplifier with a sophisticated SpeakerBoost protection algorithm. Figure 1 is a block diagram of the TFA9890A. It contains three I2S input interfaces and one I2S output interface. One of I2S inputs DATAI1 and DATAI2 can be selected as the audio input stream. The third I2S input, DATAI3, is provided to support stereo applications. A `pass-through' option allows one of the I2S input interfaces to be connected directly to the I2S output. The pass-through option is provided to allow an I2S output slave device (e.g. a CODEC), connected in parallel with the TFA9890A, to be routed directly to the audio host via the I2S output. The I2S output signal on DATAO can be configured to transmit the DSP output signal, amplifier output current information, DATAI3 Left or Right signal information or amplifier gain information. The gain information can be used to facilitate communication between two devices in stereo applications. A SpeakerBoost protection algorithm, running on a CoolFlux Digital Signal Processor (DSP) core, maximizes the acoustical output of the speaker while limiting membrane excursion and voice coil temperature to a safe level. The mechanical protection implemented guarantees that speaker membrane excursion never exceeds its rated limit, to an accuracy of 10 %. Thermal protection guarantees that the voice coil temperature never exceeds its rated limit, to an accuracy of 10 C. Furthermore, advanced signal processing ensures that the audio quality is always acceptable. The protection algorithm implements an adaptive loudspeaker model that is used to predict the extent of membrane excursion. The model is continuously updated to ensure that the protection scheme remains effective even when speaker parameter values change or the acoustic enclosure is modified. Output sound pressure levels are boosted within given mechanical, thermal and quality limits. An optional Bandwidth extension mode extends the low frequency response up to a predefined limit before maximizing the output level. This mode is suitable for listening to high-quality music in quiet environments. The frequency response of the TFA9890A can be modified via ten fully programmable cascaded second-order biquad filters. The first two biquads are processed with 48-bit double precision; biquads 3 to 8 are processed with 24-bit single precision. At low battery voltage levels, the gain is automatically reduced to limit battery current. The output volume can be controlled by the SpeakerBoost protection algorithm or by the host application (external). In the latter case, the boost features of the SpeakerBoost protection algorithm must be disabled to avoid neutralizing external volume control. The SpeakerBoost protection algorithm output is converted into two pulse width modulated (PWM) signals which are then injected into the class-D audio amplifier. The 3-level PWM scheme supports filterless speaker drive. An adaptive DC-to-DC converter boosts the battery supply voltage in line with the output of the SpeakerBoost protection algorithm. It switches to Follower mode (VBST = VBAT; no boost) when the audio output voltage is lower than the battery voltage. TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 8 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 8.1 Amplifier operating modes The TFA9890A supports five operating modes: * Power-down mode, with low supply current * Operating mode, in which the amplifier is fully operational * Mute mode, in which the class-D output is switching but the audio input signal is suppressed * Off mode, in which the device is biased, but the class-D output is floating * Fault mode, when a protection mechanism (other than SpeakerBoost protection) has been activated 8.1.1 Power-down mode Power consumption is at a minimum in Power-down mode. The TFA9890A switches to Power-down mode when: * the reset input (pin RST) goes HIGH (all digital circuits, including the DSP and RAM memory, are reset) * VDDD is switched off (< 0.8 V), triggering a complete reset of the TFA9890A * I2C control bit I2CR is set to 1 (only the I2C registers are reset, the DSP and RAM remain configured) * I2C control bit PWDN is set to 1 (the default setting, the TFA9890A is not reset when PWDN is set to 1) * there is no valid clock signal on I2S inputs BCK or WS (removing the I2S clock signals does not cause the TFA9890A to be reset) The I2C-bus remains operational in Power-down mode with the PWM outputs floating. 8.1.2 Operating mode Operating mode is selected by applying a valid clock signal (see Section 8.3) to the WS and BCK inputs. In Operating mode, I2S data input 1 or 2 (DATAI1/DATAI2) is used as the audio input. By default, the digital audio signal is processed in the CoolFlux DSP. The processed audio signal is converted into a 3-level modulated PWM signal that is fed to the output terminals. By default, the CoolFlux DSP protects the speaker in Operating mode. When the DSP is bypassed, the I2S audio input is fed directly to the amplifier with fixed gain. The peak output voltage is 8 V at 6 dBFS. If the input voltage is above this level, the output will clip and the DC-to-DC converter output may be distorted. Without speaker protection, a high output voltage can damage the speaker. To avoid over-driving the speaker, it is advised only to bypass the DSP at reduced input levels and not to use the boost converter (see Section 8.4) when the CoolFlux DSP is bypassed. Remark: In Operating mode, the TFA9890A expects the same frequency on WS as was selected via bits I2SSR in the I2S control register (i.e. the input sample rate). TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 9 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 8.1.3 Mute mode Soft muting is used to prevent audible pop noise. The transition from Operating mode to Mute mode and from Mute mode to Operating mode is implemented using an exponential function. The transition time is about 10 ms for a 48 kHz I2S input signal, and it scales with the frequency of the input signal. The I2S signal must be stable during the transition time. Mute mode is implemented in the CoolFlux DSP core and is only available when CoolFlux is not bypassed. 8.1.4 Off mode In off mode, the outputs of the class-D amplifier are floating and the device is fully biased. The transition to Off mode can be direct, or can be combined with a soft mute (providing the CoolFlux DSP is not bypassed; the I2S clock and WS signals must be stable when soft mute is activated). 8.1.5 Fault mode The TFA9890A switches to Fault mode when a protection mechanism is triggered. In Fault mode, the class-D outputs are floating. 8.2 I2S interface and channel selection I2S input interfaces 1 and 2 (DATAI1 and DATAI2) are multiplexed internally to the I2S interface block (see Figure 1). I2C control bit ISEL is used to select the I2S interface. The word select or bit clock signal of the selected I2S input can be used as the reference signal for the I2S input interface, the I2S output interface and the Phased Locked Loop (PLL). To prevent pop and click noise, the TFA9890A should be in Off mode when the value of ISEL is changed. Note that the PLL clock is used as a reference for the entire chip. Crosstalk to the I2S clock must also be prevented in the application. Extreme clock jitter can affect the reliability of speaker measurements. The I2S output, DATAO, can be enabled (active) or disabled (floating). DATAO can also be connected directly to DATAI1, DATAI2 or DATAI3 by selecting pass-through mode. 8.3 Interface formats The I2S digital audio formats supported by the TFA9890A are listed in Table 4. The I2S digital audio format for the input and output interface is selected via bits I2SF in the I2S control register. Table 4. I2S-supported digital audio formats Interface format (MSB first) I2S TFA9890A_SDS Product short data sheet (Philips) standard Supported data format BCK frequency up to 16-bit 32fs MSB-justified up to 16-bit 32fs LSB-justified - 16 bits 16-bit 32fs I2S up to 24-bit 48fs (Philips) standard MSB-justified up to 24-bit 48fs LSB-justified - 16 bits 16-bit 48fs LSB-justified - 18 bits 18-bit 48fs All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 10 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection Table 4. I2S-supported digital audio formats Interface format (MSB first) Supported data format BCK frequency LSB-justified - 20 bits 20-bit 48fs LSB-justified - 24 bits 24-bit 48fs I2S up to 24-bit 64fs (Philips) standard MSB-justified up to 24-bit 64fs LSB-justified - 16 bits 16-bit 64fs LSB-justified - 18 bits 18-bit 64fs LSB-justified - 20 bits 20-bit 64fs LSB-justified - 24 bits 24-bit 64fs The TFA9890A supports nine I2S sample rates: 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz and 48 kHz. The I2S input sample rate is selected via bits I2SSR in the I2S control register. To prevent pop and click noise, the TFA9890A should be in Power-down mode when the sample rate is changed. The BCK frequency (32, 48 or 64 times fs) is set automatically. Remark: The sample rate on the input interface should always be in line with the sample rate selected via I2SSR. The SpeakerBoost protection algorithm will not operate correctly if they are different. TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 11 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection RIGHT LEFT WS 1 2 3 1 2 3 MSB B2 BCK MSB DATA B2 MSB I2S-BUS FORMAT LEFT WS 1 2 RIGHT 3 1 2 3 BCK DATA MSB B2 LSB MSB B2 LSB MSB B2 MSB-JUSTIFIED FORMAT WS LEFT RIGHT 16 1 16 B15 LSB MSB 15 2 15 2 1 BCK DATA MSB B2 B2 B15 LSB LSB-JUSTIFIED FORMAT 16 BITS WS LEFT RIGHT 18 17 16 1 18 B17 LSB MSB 15 2 17 16 15 2 1 BCK DATA MSB B2 B3 B4 B2 B3 B4 B17 LSB LSB-JUSTIFIED FORMAT 18 BITS WS LEFT 20 RIGHT 19 18 17 16 1 20 B19 LSB MSB 15 2 19 18 17 16 15 2 1 BCK DATA MSB B2 B3 B4 B5 B6 B2 B3 B4 B5 B6 B19 LSB LSB-JUSTIFIED FORMAT 20 BITS WS LEFT 24 23 22 21 20 RIGHT 19 18 17 16 15 2 1 24 B23 LSB MSB 23 22 21 20 19 18 17 16 15 2 1 BCK DATA MSB B2 B3 B4 B5 B6 B7 B8 B9 B10 B2 B3 B4 B5 B6 B7 B8 B9 B10 B23 LSB 010aaa458 LSB-JUSTIFIED FORMAT 24 BITS Fig 4. I2S-supported digital audio data formats 8.4 DC-to-DC converter The DC-to-DC converter in the TFA9890A operates independently of the amplifier. It features a feed-forward control function that lowers the ripple on the boosted output voltage. Four converter modes are supported: * Disabled mode, when the class-D amplifier is supplied externally (not via the internal DC-to-DC converter) * Follower mode, when input INB is switched low-ohmic to VBST (no boost; VBST = battery voltage). * Boost mode, when the battery voltage is boosted * Adaptive boost mode, when the DC-to-DC converter boosts the battery voltage in line with the audio signal. TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 12 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 8.5 Battery supply safeguard The TFA9890A employs a safeguard mechanism to protect the connected battery. This feature limits the TFA9890A current when the battery voltage falls below a programmable safeguard threshold (default is 3.53 V). The battery voltage is sensed via pin VBAT. 8.6 Pulse width modulation controller The PWM controller translates the digital input signal into a 3-level PWM output signal. The PWM switching frequency depends on the sample rate. Table 5. PWM switching frequency of the class-D amplifier Sample rate fPWM fs = 8, 16 or 32 kHz 256 kHz fs = 11.025, 22.05 or 44.1 kHz 352.8 kHz fs = 12, 24 or 48 kHz 384 kHz 8.7 Protection mechanisms The following protection circuits are included in the TFA9890A: * * * * * OverTemperature Protection (OTP) OverVoltage Protection (OVP) UnderVoltage Protection (UVP) OverCurrent Protection (OCP) Invalid Data Protection (IDP) The reaction of the device to fault conditions differs depending on the protection circuit involved. 8.8 Amplifier transfer function The transfer function from the CoolFlux DSP output (CFOUT) or directly from the I2S input (CoolFlux DSP is bypassed) to the amplifier PWM outputs is: V O = CF OUT 16 V [V] (1) The CFOUT or I2S signal is specified in a range from 1 to +1 (full scale dBFS). TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 13 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 9. Internal circuitry Table 6. Pin Internal circuitry Symbol Equivalent circuit C1, C4, D1, DATAI2, TEST5, WS2, D3, E1, F2, TEST3, BCK2, ADS1, F3 ADS2 C1, C4, D1, D3, E1, F2, F3 ESD GNDD (E4) 010aaa788 A1, A2, A4, B1, B3, E3, G1 WS1, DATAI1, INT, BCK1, DATAI3, TEST2, SCL, VDDP (B6) ESD A1, A2, A4, B1, B3, E3, G1 ESD ESD GNDP (B7) GNDD (E4) 010aaa789 C3 TEST4 VDDD (E3) ESD C3 ESD GNDD (E4) 010aaa790 D4 TEST6 ' (6' *1'3 % DDD E4 TEST7 ( (6' *1'3 ( DDD F1 SDA F1 ESD GNDD (E4) 010aaa791 TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 14 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection Table 6. Internal circuitry Pin Symbol B4 RST Equivalent circuit % N (6' *1'' ( DDD A3 DATAO VDDD (E3) A3 ESD GNDD (E4) GNDP (B7) 010aaa792 A6, C6 OUTB, OUTA VDDP (B6) A6, C6 GNDP (B7) 010aaa787 E6, F6, G6 INB SENSE (E6) E6, F6, G6 GNDB (D7) 010aaa793 A5, B2, B5, B6, C2, C5, D2, D5, E2, E5, F4, F5, G4, G5 GNDP, GNDB, GNDD GNDD (A5, B2, C2, D2, D5, E2, F4, G4) GNDP (B5, B6, C5) GNDB (E5, F5, G5) 010aaa794 10. I2C-bus interface and register settings The TFA9890A supports the 400 kHz I2C-bus microcontroller interface mode standard. The I2C-bus is used to control the TFA9890A and to transmit and receive data. The TFA9890A can only operate in I2C slave mode, as a slave receiver or as a slave transmitter. TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 15 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 10.1 TFA9890A addressing The TFA9890A is accessed via an 8-bit code (see Table 7). Bits 1 to 7 contain the device address. Bit 0 (R/W) indicates whether a read (1) or a write (0) operation has been requested. Four separate addresses are supported for stereo applications. Address selection is via pins ADS1 and ADS2. The levels on pins ADS1 and ADS2 determine the values of bits 1 and 2, respectively, of the device address, as detailed in Table 7. The generic address is independent of pins ADS1 and ADS2. Table 7. TFA9890A_SDS Product short data sheet Address selection via pins ADS1 and ADS2 ADS2 pin voltage (V) ADS1 pin voltage (V) Address Function 0 0 01101000 for write mode 01101001 for read mode 0 VDDD 01101010 for write mode 01101011 for read mode for write mode VDDD 0 01101100 01101101 for read mode VDDD VDDD 01101110 for write mode 01101111 for read mode don't care don't care 00011100 (generic address) for write mode don't care don't care 00011101 (generic address) for read mode All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 16 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 11. Limiting values Table 8. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VBAT battery supply voltage on pin VBAT 0.3 +5.5 V Vx voltage on pin x pin BST 0.3 +12 V pins SDA and SCL 0.3 +3.6 V pins DATAI1, WS1, BCK1, DATAI2, WS2, BCK2, RST and test pins 0.3 +5.5 V VDDP power supply voltage on pin VDDP 0.3 +12 V VDDD digital supply voltage on pin VDDD 0.3 +1.95 V Tj junction temperature - +150 C Tstg storage temperature 55 +150 C Tamb ambient temperature VESD electrostatic discharge voltage 40 +85 C according to Human Body Model (HBM) 2 +2 kV according to Charge Device Model (CDM) 500 +500 V Typ Max Unit 43 - 12. Thermal characteristics Table 9. Thermal characteristics Symbol Parameter Rth(j-a) Conditions thermal resistance from junction to 4-layer application board positioned vertically in free ambient air; dimensions: 30 19 1.6 mm; natural convection; copper coverage on each layer > 95 %; copper thickness outer/inner layer 35 m TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 K/W (c) NXP Semiconductors N.V. 2014. All rights reserved. 17 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 13. Characteristics 13.1 DC Characteristics Table 10. DC characteristics All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 9.5 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit VBAT battery supply voltage on pin VBAT 2.7 - 5.5 V VINB voltage on pin INB boost converter input 2.7 - 5.5 V IBAT battery supply current on pin VBAT - 4 6 mA IINB current on pin INB no output signal - 1 5 A maximum output signal - - [2] mA VDDP power supply voltage on pin VDDP 3 - 9.5 V VDDD digital supply voltage on pin VDDD 1.65 1.8 1.95 V IDDD digital supply current on pin VDDD; Operating modes; SpeakerBoost Protection activated - 20 - mA on pin VDDD; Operating modes; CoolFlux DSP bypassed - 6 - mA on pin VDDD; Power-down mode; BCK1 = WS1 = DATAI1 = BCK2 = WS2 = DATAI2 = DATAI3 = 0 V - 10 50 A Pins BCK1, WS1, DATA1, BCK2, WS2, DATAI2, DATAI3, ADS1, ADS2, SCL, SDA, RST VIH HIGH-level input voltage 0.7VDDD - 3.6 V VIL LOW-level input voltage - - 0.3VDDD V - - 3 pF 1.8 V on input pin - - 0.1 A Cin input capacitance ILI input leakage current [3] Pins DATAO, INT, push-pull output stages VOH HIGH-level output voltage IOH = 4 mA - - VDDD 0.4 V VOL LOW-level output voltage IOL = 4 mA - - 400 mV Pins SDA, open-drain outputs, external 10 k resistor to VDDD VOH HIGH-level output voltage IOH = 4 mA - - VDDD 0.4 V VOL LOW-level output voltage IOL = 4 mA - - 400 mV VDDP = 9.5 V - 200 - m Pins OUTA, OUTB RDSon drain-source on-state resistance Protection Tact(th_prot) thermal protection activation temperature 130 - 150 C Vovp(VBAT) overvoltage protection voltage on pin VBAT 5.5 - 6.0 V Vuvp(VBAT) undervoltage protection voltage on pin VBAT 2.3 - 2.5 V TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 18 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection Table 10. DC characteristics ...continued All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 9.5 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. ...continued Symbol Parameter IO(ocp) overcurrent protection output current Conditions Min Typ Max Unit 2 - - A 9.4 9.5 9.6 V DC-to-DC converter VBST voltage on pin BST DCVO = 111; Boost mode [1] LBST = boost converter inductance; RL = load resistance; LL = load inductance (speaker). [2] Maximum value determined by the I2C setting. [3] This parameter is not tested during production; the value is guaranteed by design and checked during product validation. TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 19 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 13.2 AC characteristics Table 11. AC characteristics All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 9.5 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit RL = 8 ; fs = 48 kHz - 3.6 - W RL = 8 ; fs = 32 kHz - 3.7 - W RL = 8 ; fs = 48 kHz - 4.5 - W RL = 8 ; fs = 32 kHz - 4.6 - W - - 6 mV [2] - 72 - % [1] - 0.03 0.1 % - 50 - V - 66 - V - 100 - dB - 97 - dB - 75 - dB 256 - 384 kHz - 16 - V - - 2 ms Amplifier output power Po(RMS) RMS output power THD+N = 1 %; CLIP = 0 THD+N = 10 %; CLIP = 0 Amplifier output; pins OUTA and OUTB VO(offset) output offset voltage absolute value Amplifier performance po output power efficiency THD+N total harmonic distortion-plus-noise Po(RMS) = 100 mW; RL = 8 ; LL = 44 H Vn(o) output noise voltage Po(RMS) = 2.5 W; including DC-to-DC converter; 100 Hz audio signal A-weighted; DATAI1 = DATAI2 = 0 V CoolFlux DSP bypassed [2] CoolFlux DSP enabled S/N signal-to-noise ratio VO = 4.5 V (peak); A-weighted CoolFlux DSP bypassed [2] CoolFlux DSP enabled PSRR power supply rejection ratio Vripple = 200 mV (RMS); fripple = 217 Hz I2S fsw switching frequency directly coupled to the frequency input Vo output voltage CoolFlux DSP bypassed; 1 to +1 (full scale dBFS) digital input Amplifier power-up, power-down and propagation delays td(on) turn-on delay time PLL locked on BCK (IPLL = 0) fs = 8 kHz to 48 kHz PLL locked on WS (IPLL = 1) td(off) turn-off delay time td(mute_off) mute off delay time td(soft_mute) soft mute delay time td(pilot_off) pilot off delay time fs = 8 kHz - - 27 ms fs = 48 kHz - - 6 ms - - 10 s - ms after a soft mute; fs = 48 kHz after a soft mute; fs = 32 kHz TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 - 1 [3] - 12 - ms [3] - 11 21 ms - 16 32 ms (c) NXP Semiconductors N.V. 2014. All rights reserved. 20 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection Table 11. AC characteristics All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 9.5 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. ...continued Symbol Parameter Conditions tPD propagation delay CoolFlux bypassed Min Typ Max Unit fs = 8 kHz - - 3.2 ms fs = 48 kHz - - 600 s SpeakerBoost protection mode, tLookAhead = 2 ms fs = 8 kHz - - 14 ms fs = 48 kHz - - 4 ms - 75 - dB Current-sensing performance S/N signal-to-noise ratio IO = 1.2 A (peak); A-weighted Isense(acc) sense current accuracy IO = 0.5 A (peak) B bandwidth LL load inductance [1] [3] 3 - +3 % - 8 - kHz 20 - - H LBST = boost converter inductor; RL = load resistance; LL = load inductance (speaker). [2] This parameter is not tested during production; the value is guaranteed by design and checked during product validation. [3] The soft mute delay is the delay of the cosine role off of the audio. The pilot tone is removed at the zero crossing after a soft mute, with a delay of td(pilot_off). This takes a maximum of 21 ms (average 11 ms) at an input sample rate of 12 kHz, 24 kHz or 48 kHz. At an input sample rate of 8 kHz, 16 kHz or 32 kHz, the delay is 32 ms (max). So the worst case mute delay is 12 + 21 = 33 or 12 + 32 = 44 ms, depending on the sample frequency. TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 21 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 13.3 I2S timing characteristics Table 12. I2S bus interface characteristics; see Figure 5 All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 9.5 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fs sampling frequency on pin WS [2] 8 - 48 kHz fclk clock frequency on pin BCK [2] 32fs - 64fs Hz WS edge to BCK HIGH [3] 10 - - ns 10 - - ns 10 - - ns 10 - - ns set-up time tsu DATA edge to BCK HIGH hold time th [3] BCK HIGH to WS edge BCK HIGH to DATA edge [1] LBST = boost converter inductance; RL = load resistance; LL = load inductance. [2] The I2S bit clock input (BCK) is used as a clock input for the DSP, as well as for the amplifier and the DC-to-DC converter. Both the BCK and WS signals must be present for the clock to operate correctly. [3] This parameter is not tested during production; the value is guaranteed by design and checked during product validation. BCK th tsu WS DATA 010aaa750 Fig 5. TFA9890A_SDS Product short data sheet I2S timing All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 22 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 13.4 I2C timing characteristics Table 13. I2C-bus interface characteristics; see Figure 6 All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 9.5 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fSCL tLOW SCL clock frequency - - 400 kHz LOW period of the SCL clock 1.3 - - s tHIGH HIGH period of the SCL clock rise time tr 0.6 - - s SDA and SCL signals [2] 20 + 0.1 Cb - - ns SDA and SCL signals [2] 20 + 0.1 Cb - - ns [3] 0.6 - - s 0.6 - - s tf fall time tHD;STA hold time (repeated) START condition tSU;STA set-up time for a repeated START condition tSU;STO set-up time for STOP condition 0.6 - - s tBUF bus free time between a STOP and START condition 1.3 - - s tSU;DAT data set-up time 100 - - ns 0 - - s 0 - 50 ns - - 400 pF tHD;DAT data hold time tSP pulse width of spikes that must be suppressed by the input filter Cb capacitive load for each bus line [4] [1] LBST = boost converter inductance; RL = load resistance; LL = load inductance. [2] Cb is the total capacitance of one bus line in pF. The maximum capacitive load for each bus line is 400 pF. [3] After this period, the first clock pulse is generated. [4] To be suppressed by the input filter. SDA tLOW tBUF tr tf tHD;STA tSP SCL tHD;STA P tHD;DAT tHIGH tSU;DAT S tSU;STA Sr tSU;STO P 010aaa225 Fig 6. I2C timing 14. Application information 14.1 External components Figure 7 shows the minimum number of external components needed in an application. The DC-to-DC converter needs a battery supply voltage capacitor (CVBAT), an output capacitor (CVDDP) and an inductor (LBST) to work properly. The nominal values of these TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 23 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection components are 10 nF, 20 F and 1 H, respectively. A 100 nF decoupling capacitor (CVDDD) must be connected close to the VDDD pin. The total capacitance at this supply line should be at least 1 F. 14.1.1 DC-to-DC converter output capacitor A ceramic capacitor is required at the output of the DC-to-DC converter (CVDDP). Capacitors constructed using X5R (55 C to +85 C) or X7R (55 C to +125 C) dielectric materials are preferred because they are compact, feature low ESR and are sufficiently stable over a wide temperature range. The capacitance value decreases over the DC biasing voltage range (30 % to 70 % decrease). Consequently, the nominal value of the capacitor should be close to twice the minimum value specified. Remark: The DC-to-DC converter capacitor connected to BST is critical for stability. The recommended effective value (the capacitance value at the maximum boost voltage) of CVDDP depends on the coil inductance, and is given in Table 14. The position of the capacitor and the layout of the board are also critical. It is recommended to connect CVDDP as close as possible to the BST and GNDD pins without vias in the PCB tracks. In many applications, it is desirable to limit the height of components as much as possible. This can be achieved for CVDDP by connecting two smaller capacitors in parallel. The rated voltage should be 10 V or higher. Table 14. Suggested effective value for DC-to-DC converter output capacitor (CVDDP) Effective coil value (at maximum current) Minimum effective capacitance (at the boost voltage) 1 H 6 F 14.1.2 Supply capacitor CBST can be about half the value of CVDDP. 14.1.3 DC-to-DC converter inductor An inductor is required at the output of the DC-to-DC converter (LBST). For stability, the inductance of the coil should remain above 0.7 H and below 1.2 H under all conditions. A DC-to-DC coil value of 1 H or less is strongly recommended. If the coil value is increased, the value of the output capacitor will also need to be increased by at least the same factor. If the output capacitor is not large enough, the DC-to-DC converter will be unstable. The positioning of the output capacitor on the PCB is also critical. The capacitor must be located as close as possible to the TFA9890A and the connections between them should be on the top layer. A nominal value of 1 H provides the optimum balance between current capability, component size and efficiency. The choice of inductor is strongly influenced by the impedance of the speaker used in the application. The speaker impedance determines the output current of the DC-to-DC converter. The minimum required battery voltage, the boost voltage and the inductor value determine the peak inductor current (ILM). 14.1.4 Reset pin (RST) If the reset pin is not used, it is advised to connect it directly to ground. It has an internal pull-down resistance of 100 k. TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 24 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 14.2 Application diagrams EDWWHU\ /%67 9 + &9''' 567 ,17 '$7$, :6 %&. '$7$, 9''3 ()* %67 ,1% $ $ ' % ' $ & 7)$$ QF QF 287$ VSHDNHU % $ $ & ' ( % $'6 ) ) ( ) * % % $ % & & ' ' ( ) * ( ' & ( ' 287% 7(67 7(67 7(67 & 7(67 '$7$2 ()* 7(67 %&. $ % & 7(67 :6 ,6 ) ) * *1'' '$7$, * *1'3 6&/ * *1'% ,& &9''3 ) $'6 6'$ Q) 9%$7 %$6(%$1' 352&(6625 &9%$7 9''' Q) &%67 DDD Fig 7. TFA9890A_SDS Product short data sheet Typical mono application (simplified) All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 25 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection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ig 8. Typical stereo application (simplified) TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 26 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection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ig 9. Typical mono application with two audio sources and a second I2S slave device TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 27 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 14.3 Curves measured in reference design (demonstration board) All measurements were taken with VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 9.5 V; LBST = 1 H; RL = 8 ; LL = 20 H; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; CoolFlux DSP bypassed; default settings, unless otherwise specified. 010aaa825 102 THD+N (%) 010aaa826 1 THD+N (%) 10 (1) (2) (3) 1 (1) (2) 10-1 10-1 10-2 10-3 10-2 10-1 1 Po (W) 10 10-2 102 10 (1) fi = 6 kHz. (1) Po = 100 mW (2) fi = 1 kHz. (2) Po = 500 mW 103 104 fi (Hz) 105 (3) fi = 100 Hz. Fig 10. THD plus noise as a function of output power 010aaa833 0.6 P (W) Fig 11. THD plus noise as a function of frequency 0.48 80 0.36 60 0.24 40 0.12 20 0 10-3 10-2 10-1 1 Po (W) 10 fi = 100 Hz, intelligent boost mode, DSP bypassed Fig 12. Power dissipation as a function of output power TFA9890A_SDS Product short data sheet 010aaa829 100 (%) 0 0 1 2 3 4 Po (W) 5 fi = 100 Hz, intelligent boost mode, DSP bypassed Fig 13. Efficiency as a function of output power All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 28 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 010aaa827 1.4 G (dB) 010aaa828 7 Po (W) 5.6 0.7 4.2 (4) (3) (1) (2) 0 2.8 -0.7 1.4 -1.4 102 10 103 104 fi (Hz) 0 105 Po = 500 mW 2 2.8 3.6 4.4 5.2 VBAT (V) 6 (1) THD+N = 10 %, no boost (Follower mode) (2) THD+N = 1 %, no boost (Follower mode) (3) THD+N = 10 %, boost on (4) THD+N = 1 %, boost on Fig 14. Normalized gain as a function of frequency DDD 9%67 9 DDD ,%$7 $ Fig 15. Output power as a function of battery supply voltage 9%67 9 ,%$7 9 9%67 ,%$7 W V 9%67 ,%$7 W V input signal is a sine wave; fi = 100 Hz a. fast ramp-up b. immediate ramp-up Fig 16. DC-to-DC converter ramp-up behavior TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 29 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 010aaa832 -10 PSRR (dB) -30 -50 -70 -90 -110 102 10 103 104 fripple (Hz) 105 Vripple = 200 mV(RMS) on VBAT Fig 17. PSRR as a function of ripple frequency TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 30 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 15. Package outline :/&63ZDIHUOHYHOFKLSVL]HSDFNDJH EXPSV[PP 7)$$ ' % $ EDOO$ LQGH[DUHD $ $ ( $ GHWDLO; H & E H =( Y Z * & $ % & \ H ) ( H ' & % $ =( =' EDOO$ LQGH[DUHD =' ; PP VFDOH 'LPHQVLRQV PPDUHWKHRULJLQDOGLPHQVLRQV 8QLW $PD[ PD[ QRP PLQ PP $ $ E ' ( H H H Y Z \ =' =' =( =( ZOFVSBWIDDBSR 2XWOLQH YHUVLRQ 5HIHUHQFHV ,(& -('(& -(,7$ (XURSHDQ SURMHFWLRQ ,VVXHGDWH 7)$$ Fig 18. Package outline TFA9890A (WLCSP49) TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 31 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 16. Soldering of WLCSP packages 16.1 Introduction to soldering WLCSP packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering WLCSP (Wafer Level Chip-Size Packages) can be found in application note AN10439 "Wafer Level Chip Scale Package" and in application note AN10365 "Surface mount reflow soldering description". Wave soldering is not suitable for this package. All NXP WLCSP packages are lead-free. 16.2 Board mounting Board mounting of a WLCSP requires several steps: 1. Solder paste printing on the PCB 2. Component placement with a pick and place machine 3. The reflow soldering itself 16.3 Reflow soldering Key characteristics in reflow soldering are: * Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 19) than a SnPb process, thus reducing the process window * Solder paste printing issues, such as smearing, release, and adjusting the process window for a mix of large and small components on one board * Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature), and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic) while being low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 15. Table 15. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 19. TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 32 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 19. Temperature profiles for large and small components For further information on temperature profiles, refer to application note AN10365 "Surface mount reflow soldering description". 16.3.1 Stand off The stand off between the substrate and the chip is determined by: * The amount of printed solder on the substrate * The size of the solder land on the substrate * The bump height on the chip The higher the stand off, the better the stresses are released due to TEC (Thermal Expansion Coefficient) differences between substrate and chip. 16.3.2 Quality of solder joint A flip-chip joint is considered to be a good joint when the entire solder land has been wetted by the solder from the bump. The surface of the joint should be smooth and the shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps after reflow can occur during the reflow process in bumps with high ratio of bump diameter to bump height, i.e. low bumps with large diameter. No failures have been found to be related to these voids. Solder joint inspection after reflow can be done with X-ray to monitor defects such as bridging, open circuits and voids. 16.3.3 Rework In general, rework is not recommended. By rework we mean the process of removing the chip from the substrate and replacing it with a new chip. If a chip is removed from the substrate, most solder balls of the chip will be damaged. In that case it is recommended not to re-use the chip again. TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 33 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection Device removal can be done when the substrate is heated until it is certain that all solder joints are molten. The chip can then be carefully removed from the substrate without damaging the tracks and solder lands on the substrate. Removing the device must be done using plastic tweezers, because metal tweezers can damage the silicon. The surface of the substrate should be carefully cleaned and all solder and flux residues and/or underfill removed. When a new chip is placed on the substrate, use the flux process instead of solder on the solder lands. Apply flux on the bumps at the chip side as well as on the solder pads on the substrate. Place and align the new chip while viewing with a microscope. To reflow the solder, use the solder profile shown in application note AN10365 "Surface mount reflow soldering description". 16.3.4 Cleaning Cleaning can be done after reflow soldering. TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 34 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 17. Revision history Table 16. Revision history Document ID Release date Data sheet status Change notice Supersedes TFA9890A_SDS v.1 20140916 Product short data sheet - - TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 35 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 18. Legal information 18.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 18.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 18.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. TFA9890A_SDS Product short data sheet Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 36 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Quick reference data -- The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 18.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- logo is a trademark of NXP Semiconductors N.V. CoolFlux -- is a trademark of NXP Semiconductors N.V. 19. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com TFA9890A_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 16 September 2014 (c) NXP Semiconductors N.V. 2014. All rights reserved. 37 of 38 TFA9890A NXP Semiconductors 9.5 V boosted audio system with adaptive sound maximizer and speaker protection 20. Contents 1 2 3 4 5 6 7 7.1 8 8.1 8.1.1 8.1.2 8.1.3 8.1.4 8.1.5 8.2 8.3 8.4 8.5 8.6 8.7 8.8 9 10 10.1 11 12 13 13.1 13.2 13.3 13.4 14 14.1 14.1.1 14.1.2 14.1.3 14.1.4 14.2 14.3 15 16 16.1 16.2 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Quick reference data . . . . . . . . . . . . . . . . . . . . . 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 8 Amplifier operating modes . . . . . . . . . . . . . . . . 9 Power-down mode . . . . . . . . . . . . . . . . . . . . . . 9 Operating mode . . . . . . . . . . . . . . . . . . . . . . . . 9 Mute mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Off mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Fault mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 I2S interface and channel selection . . . . . . . . 10 Interface formats. . . . . . . . . . . . . . . . . . . . . . . 10 DC-to-DC converter . . . . . . . . . . . . . . . . . . . . 12 Battery supply safeguard . . . . . . . . . . . . . . . . 13 Pulse width modulation controller . . . . . . . . . . 13 Protection mechanisms . . . . . . . . . . . . . . . . . 13 Amplifier transfer function . . . . . . . . . . . . . . . . 13 Internal circuitry. . . . . . . . . . . . . . . . . . . . . . . . 14 I2C-bus interface and register settings . . . . . 15 TFA9890A addressing . . . . . . . . . . . . . . . . . . 16 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 17 Thermal characteristics . . . . . . . . . . . . . . . . . 17 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 18 DC Characteristics . . . . . . . . . . . . . . . . . . . . . 18 AC characteristics. . . . . . . . . . . . . . . . . . . . . . 20 I2S timing characteristics . . . . . . . . . . . . . . . . 22 I2C timing characteristics . . . . . . . . . . . . . . . . 23 Application information. . . . . . . . . . . . . . . . . . 23 External components . . . . . . . . . . . . . . . . . . . 23 DC-to-DC converter output capacitor . . . . . . . 24 Supply capacitor . . . . . . . . . . . . . . . . . . . . . . 24 DC-to-DC converter inductor . . . . . . . . . . . . . 24 Reset pin (RST) . . . . . . . . . . . . . . . . . . . . . . . 24 Application diagrams . . . . . . . . . . . . . . . . . . . 25 Curves measured in reference design (demonstration board) . . . . . . . . . . . . . . . . . . 28 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 31 Soldering of WLCSP packages. . . . . . . . . . . . 32 Introduction to soldering WLCSP packages . . 32 Board mounting . . . . . . . . . . . . . . . . . . . . . . . 32 16.3 16.3.1 16.3.2 16.3.3 16.3.4 17 18 18.1 18.2 18.3 18.4 19 20 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . Stand off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quality of solder joint . . . . . . . . . . . . . . . . . . . Rework. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 33 33 33 34 35 36 36 36 36 37 37 38 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP Semiconductors N.V. 2014. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 16 September 2014 Document identifier: TFA9890A_SDS