MC74AC138, MC74ACT138 1-of-8 Decoder/Demultiplexer The MC74AC138/74ACT138 is a high-speed 1-of-8 decoder/demultiplexer . This device is ideally suited for high-speed bipolar memory chip select address decoding. The multiple input enables allow parallel expansion to a 1-of-24 decoder using just three MC74AC138/74ACT138 devices or a 1-of-32 decoder using four MC74AC138/74ACT138 devices and one inverter. * * * * * Demultiplexing Capability Multiple Input Enable for Easy Expansion Active LOW Mutually Exclusive Outputs Outputs Source/Sink 24 mA ACT138 Has TTL Compatible Inputs VCC O0 O1 O2 O3 O4 O5 O6 16 15 14 13 12 11 10 9 http://onsemi.com DIP-16 N SUFFIX CASE 648 16 1 16 1 16 1 1 A0 2 A1 3 A2 4 E1 5 E2 6 E3 7 O7 8 GND TSSOP-16 DT SUFFIX CASE 948F EIAJ-16 M SUFFIX CASE 966 16 1 Figure 1. Pinout: 16-Lead Packages Conductors (Top View) ORDERING INFORMATION Device A0 A1 A2 SO-16 D SUFFIX CASE 751B E1 E2 E3 O0 O1 O2 O3 O4 O5 O6 O7 Figure 2. Logic Symbol Package Shipping MC74AC138N PDIP-16 25 Units/Rail MC74ACT138N PDIP-16 25 Units/Rail MC74AC138D SOIC-16 48 Units/Rail MC74ACT138D SOIC-16 48 Units/Rail MC74AC138DR2 SOIC-16 2500 Tape & Reel MC74ACT138DR2 SOIC-16 2500 Tape & Reel MC74AC138DT TSSOP-16 96 Units/Rail 96 Units/Rail MC74ACT138DT TSSOP-16 PIN ASSIGNMENT MC74AC138DTR2 TSSOP-16 2500 Tape & Reel PIN FUNCTION MC74ACT138DTR2 TSSOP-16 2500 Tape & Reel A0-A2 Address Inputs MC74AC138M EIAJ-16 50 Units/Rail E1-E2 Enable Inputs MC74ACT138M EIAJ-16 50 Units/Rail E3 Enable Input MC74AC138MEL EIAJ-16 2000 Tape & Reel O0-O7 Outputs MC74ACT138MEL EIAJ-16 2000 Tape & Reel DEVICE MARKING INFORMATION See general marking information in the device marking section on page 6 of this data sheet. Semiconductor Components Industries, LLC, 2001 May, 2001 - Rev. 5 1 Publication Order Number: MC74AC138/D MC74AC138, MC74ACT138 FUNCTIONAL DESCRIPTION expansion of the device to a 1-of-32 (5 lines to 32 lines) decoder with just four MC74AC138/74ACT138 devices and one inverter (See Figure 4). The MC74AC138/74ACT138 can be used as an 8-output demultiplexer by using one of the active LOW Enable inputs as the data input and the other Enable inputs as strobes. The Enable inputs which are not used must be permanently tied to their appropriate active-HIGH or active-LOW state. The MC74AC138/74ACT138 high-speed 1-of-8 decoder/demultiplexer accepts three binary weighted inputs (A0, A1, A2) and, when enabled, provides eight mutually exclusive active-LOW outputs (O0-O7). The MC74AC138/74ACT138 features three Enable inputs, two active-LOW (E1, E2) and one active-HIGH (E3). All outputs will be HIGH unless E1 and E2 are LOW and E3 is HIGH. This multiple enabled function allows easy parallel TRUTH TABLE Inputs Outputs E1 E2 E3 A0 A1 A2 O0 O1 O2 O3 O4 O5 O6 O7 H X X X H X X X L X X X X X X X X X H H H H H H H H H H H H H H H H H H H H H H H H L L L L L L L L H H H H L H L H L L H H L L L L L H H H H L H H H H L H H H H L H H H H H H H H H H H H H H H H L L L L L L L L H H H H L H L H L L H H H H H H H H H H H H H H H H H H H H H H L H H H H L H H H H L H H H H L H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial A2 07 NOTE: A1 E1 E2 E3 A0 06 05 04 03 02 01 00 This diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. Figure 3. Logic Diagram http://onsemi.com 2 MC74AC138, MC74ACT138 A0 A1 A2 04 A3 A4 H 123 A0 A1 A2 123 E 00 01 02 03 04 05 06 07 A0 A1 A2 123 E A0 A1 A2 00 01 02 03 04 05 06 07 123 E 00 01 02 03 04 05 06 07 A0 A1 A2 E 00 01 02 03 04 05 06 07 00 031 Figure 4. Expansion to 1-of-32 Decoding MAXIMUM RATINGS* Symbol Parameter Value Unit VCC DC Supply Voltage (Referenced to GND) -0.5 to +7.0 V VIN DC Input Voltage (Referenced to GND) -0.5 to VCC +0.5 V VOUT DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V IIN DC Input Current, per Pin 20 mA IOUT DC Output Sink/Source Current, per Pin 50 mA ICC DC VCC or GND Current per Output Pin 50 mA Tstg Storage Temperature -65 to +150 C *Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage VIN, VOUT DC Input Voltage, Output Voltage (Ref. to GND) tr, tf Input Rise and Fall Time (Note 1) AC Devices except Schmitt Inputs Min Typ Max Unit AC 2.0 5.0 6.0 ACT 4.5 5.0 5.5 0 - VCC VCC @ 3.0 V - 150 - VCC @ 4.5 V - 40 - VCC @ 5.5 V - 25 - VCC @ 4.5 V - 10 - VCC @ 5.5 V - 8.0 - - - 140 C -40 25 85 C V V ns/V tr, tf In ut Rise and Fall Time (Note 2) Input ACT Devices except Schmitt Inputs TJ Junction Temperature (PDIP) TA Operating Ambient Temperature Range IOH Output Current - High - - -24 mA IOL Output Current - Low - - 24 mA ns/V 1. VIN from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. VIN from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times. http://onsemi.com 3 MC74AC138, MC74ACT138 DC CHARACTERISTICS Symbol Parameter VCC (V) 74AC 74AC TA = +25C TA = -40C to +85C Typ VIH VIL VOH VOL Guaranteed Limits 3.0 4.5 5.5 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 V VOUT = 0.1 V or VCC - 0.1 V Maximum Low Level Input Voltage 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 V VOUT = 0.1 V or VCC - 0.1 V Minimum High g Level Output Voltage 3.0 4.5 5.5 2.99 4.49 5.49 2.9 4.4 5.4 2.9 4.4 5.4 V 3.0 4.5 5.5 - - - 2.56 3.86 4.86 2.46 3.76 4.76 3.0 4.5 5.5 0.002 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 5.5 - - - 0.36 0.36 0.36 0.44 0.44 0.44 55 5.5 - 0 1 0.1 5.5 - 5.5 55 5.5 Maximum Low Level Output Voltage Maximum Input Leakage Current IOLD Minimum Dynamic O t t Current Output C t ICC Conditions Minimum High g Level Input Voltage IIN IOHD Unit Maximum Q Quiescent Supply Current V *VIN = VIL or VIH -12 mA IOH -24 mA -24 mA IOUT = 50 A V V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA 1 0 1.0 A VI = VCC, GND - 75 mA VOLD = 1.65 V Max - - -75 mA VOHD = 3.85 V Min - 80 8.0 80 A VIN = VCC or GND *All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC. http://onsemi.com 4 IOUT = -50 A MC74AC138, MC74ACT138 AC CHARACTERISTICS (For Figures and Waveforms - See Section 3 of the ON Semiconductor FACT Data Book, DL138/D) Symbol VCC* (V) Parameter 74AC 74AC TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Min Typ Max Min Max Unit Fig. No. tPLH Propagation g Delayy An to On 3.3 5.0 1.5 1.5 8.5 6.5 13.0 9.5 1.5 1.5 15.0 10.5 ns 3-6 tPHL Propagation g Delayy An to On 3.3 5.0 1.5 1.5 8.0 6.0 12.5 9.0 1.5 1.5 14.0 10.5 ns 3-6 tPLH Propagation g Delayy E1 or E2 to On 3.3 5.0 1.5 1.5 11.0 8.0 15.0 11.0 1.5 1.5 16.0 12.0 ns 3-6 tPHL Propagation g Delayy E1 or E2 to On 3.3 5.0 1.5 1.5 9.5 7.0 13.5 9.5 1.5 1.5 15.0 10.5 ns 3-6 tPLH Propagation g Delayy E3 to On 3.3 5.0 1.5 1.5 11.0 8.0 15.5 11.0 1.5 1.5 16.5 12.5 ns 3-6 tPHL Propagation g Delayy E3 to On 3.3 5.0 1.5 1.5 8.5 6.0 13.0 8.0 1.5 1.0 14.0 9.5 ns 3-6 *Voltage Range 3.3 V is 3.3 V 0.3 V. *Voltage Range 5.0 V is 5.0 V 0.5 V. DC CHARACTERISTICS Symbol Parameter VCC (V) 74ACT 74ACT TA = +25C TA = -40C to +85C Typ Guaranteed Limits Unit Conditions VIH Minimum High g Level Input Voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 V VOUT = 0.1 V or VCC - 0.1 V VIL Maximum Low Level Input Voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 V VOUT = 0.1 V or VCC - 0.1 V VOH Minimum High g Level Output Voltage 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 V 4.5 5.5 - - 3.86 4.86 3.76 4.76 4.5 5.5 0.001 0.001 0.1 0.1 0.1 0.1 4.5 5.5 - - 0.36 0.36 0.44 0.44 V *VIN = VIL or VIH 24 mA IOL 24 mA VOL Maximum Low Level Output Voltage V V IOUT = -50 A *VIN = VIL or VIH -24 mA IOH -24 mA IOUT = 50 A IIN Maximum Input Leakage Current 55 5.5 - 0 1 0.1 1 0 1.0 A VI = VCC, GND ICCT Additional Max. ICC/Input 5.5 0.6 - 1.5 mA VI = VCC - 2.1 V IOLD Minimum Dynamic O t t Current Output C t 5.5 - - 75 mA VOLD = 1.65 V Max 5.5 - - -75 mA VOHD = 3.85 V Min 55 5.5 - 80 8.0 80 A VIN = VCC or GND IOHD ICC Maximum Q Quiescent Supply Current *All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. http://onsemi.com 5 MC74AC138, MC74ACT138 AC CHARACTERISTICS (For Figures and Waveforms - See Section 3 of the ON Semiconductor FACT Data Book, DL138/D) Symbol VCC* (V) Parameter 74ACT 74ACT TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Min Typ Max Min Max Unit Fig. No. tPLH Pro agation Delay Propagation An to On 50 5.0 15 1.5 70 7.0 10 5 10.5 15 1.5 11 5 11.5 ns 3-6 tPHL Pro agation Delay Propagation An to On 50 5.0 15 1.5 65 6.5 10 5 10.5 15 1.5 11 5 11.5 ns 3-6 tPLH Pro agation Delay Propagation E1 or E2 to On 50 5.0 25 2.5 80 8.0 11 5 11.5 20 2.0 12 5 12.5 ns 3-6 tPHL Pro agation Delay Propagation E1 or E2 to On 50 5.0 20 2.0 75 7.5 11 5 11.5 20 2.0 12 5 12.5 ns 3-6 50 5.0 25 2.5 80 8.0 12 0 12.0 20 2.0 13 0 13.0 ns 3-6 50 5.0 20 2.0 65 6.5 10 5 10.5 15 1.5 11 5 11.5 ns 3-6 Pro agation Delay Propagation E3 to On Propagation Pro agation Delay tPHL E3 to On *Voltage Range 5.0 V is 5.0 V 0.5 V tPLH CAPACITANCE Symbol Parameter Value Typ Unit Test Conditions CIN Input Capacitance 4.5 pF VCC = 5.0 V CPD Power Dissipation Capacitance 60 pF VCC = 5.0 V MARKING DIAGRAMS DIP-16 SO-16 MC74AC138N AWLYYWW AC138 AWLYWW MC74ACT138N AWLYYWW ACT138 AWLYWW A WL, L YY, Y WW, W = Assembly Location = Wafer Lot = Year = Work Week http://onsemi.com 6 TSSOP-16 EIAJ-16 AC 138 ALYW 74AC138 ALYW ACT 138 ALYW 74ACT138 ALYW MC74AC138, MC74ACT138 PACKAGE DIMENSIONS PDIP-16 N SUFFIX 16 PIN PLASTIC DIP PACKAGE CASE 648-08 ISSUE R -A- 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B F C DIM A B C D F G H J K L M S L S SEATING PLANE -T- K H D M J G 16 PL 0.25 (0.010) M T A M INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0 10 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0 10 0.51 1.01 SO-16 D SUFFIX 16 PIN PLASTIC SOIC PACKAGE CASE 751B-05 ISSUE J -A- 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 -B- 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 C -T- SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A S http://onsemi.com 7 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0 7 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0 7 0.229 0.244 0.010 0.019 MC74AC138, MC74ACT138 PACKAGE DIMENSIONS TSSOP-16 DT SUFFIX 16 PIN PLASTIC TSSOP PACKAGE CASE948F-01 ISSUE O 16X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S K EEE CCC CCC EEE K1 2X L/2 16 9 J1 B -U- L SECTION N-N J PIN 1 IDENT. 8 1 N 0.15 (0.006) T U S 0.25 (0.010) A -V- M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. N F DETAIL E -W- C 0.10 (0.004) -T- SEATING PLANE DETAIL E H D LE 9 Q1 M E HE 1 8 L DETAIL P Z D e VIEW P A 0.13 (0.005) c A1 b M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0 8 INCHES MIN MAX 0.193 0.200 0.169 0.177 --0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0 8 G EIAJ-16 M SUFFIX 16 PIN PLASTIC EIAJ PACKAGE CASE966-01 ISSUE O 16 DIM A B C D F G H J J1 K K1 L M 0.10 (0.004) http://onsemi.com 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 0 10 0.70 0.90 --0.78 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 0 10 0.028 0.035 --0.031 MC74AC138, MC74ACT138 Notes http://onsemi.com 9 MC74AC138, MC74ACT138 Notes http://onsemi.com 10 MC74AC138, MC74ACT138 Notes http://onsemi.com 11 MC74AC138, MC74ACT138 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 12 MC74AC138/D