Data Sheet
Broadcom AV02-0260EN
September 15, 2017
Description
The Broadcom® ASSR-32xx Series consists of an AlGaAs
infrared light-emitting diode (LED) input stage optically
coupled to a high-voltage output detector circuit. The
detector consists of a high-speed photovoltaic diode array
and driver circuitry to switch on/off two discrete high voltage
MOSFETs. The relay turns on (contact closes) with a
minimum input current of 3 mA through the input LED. The
relay turns off (contact opens) with an input voltage of 0.8V
or less.
The single channel configurations, ASSR-3210 and
ASSR-3211, are equivalent to 1 Form A Electromechanical
Relays (EMR), and the dual channel configuration, ASSR-
3220, is equivalent to 2 Form A EMR. They are available in
4-pin SO, 6-pin DIP, 8-pin DIP and Gull Wing Surface Mount
for DIP packages. Their electrical and switching
characteristics are specified over the temperature range of
–40°C to +85°C. They are used for general purpose
switching of signals and low power AC/DC loads.
ASSR-3211 enables AC/DC and DC-only output
connections. For DC-only connection, the output current, Io,
increases to 0.4A and the on-resistance, R(ON) reduces to
2.5.
CAUTION! It is advised that normal static precautions be
taken in handling and assembly of this
component to prevent damage and/or
degradation which may be induced by ESD.
Features
Compact solid-state bidirectional signal switch
Single and dual channel normally-off Single-Pole-
Single-Throw (SPST) relay
250V output withstand voltage
0.2A or 0.4A current rating (See schematic for
ASSR-3211 connections A and B.)
Low input current: CMOS compatibility
Low on-resistance:
– 2Ω typical for DC-only
– 8Ω typical for AC/DC
High speed switching:
– 0.25 ms (TON), 0.02 ms (TOFF) typical
High transient immunity: >1 kV/μs
High input-to-output insulation voltage (safety and
regulatory approvals)
– 3750 Vrms for 1 min per UL1577
– CSA component acceptance
Applications
Telecommunication switching
Data communications
Industrial controls
Medical
Security
EMR/Reed Relay replacement
ASSR-3210, ASSR-3211, ASSR-3220
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Broadcom AV02-0260EN
2
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Functional Diagram Truth Table
Opto-isolation
Turn-off
Circuit
1
2
4
3
Single Channel, SPST Relay,
1 Form A in 4-Pin SO Package
LED Output
Off Open
On Close
Ordering Information
ASSR-32xx is UL Recognized with 3750 Vrms for 1 minute per UL1577 and is approved under CSA Component Acceptance
Notice #5.
To order, choose a part number from the part number column and combine with the desired option from the option column
to form an order entry.
Example 1:
ASSR-3211-501E to order product of 300-mil DIP-6 Gull Wing Surface Mount package in Tape and Reel packaging and
RoHS Compliant.
Example 2:
ASSR-3220-002E to order product of 300-mil DIP-8 package in tube packaging and RoHS Compliant.
Option data sheets are available. Contact your Broadcom sales representative or authorized distributor for information.
Part Number
Option
Package Surface Mount Gull Wing Tape & Reel QuantityRoHS Compliant
ASSR-3210 -003E SO-4 X 100 units per tube
-503E X X 1500 units per reel
ASSR-3211 -001E 300-mil DIP-6 50 units per tube
-301E X X 50 units per tube
-501E X X X 1000 units per reel
ASSR-3220 -002E 300-mil DIP-8 50 units per tube
-302E X X 50 units per tube
-502E X X X 1000 units per reel
Broadcom AV02-0260EN
3
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Schematic
ASSR-3210
ASSR-3211 Connection A
ASSR-3211 Connection B
Turn-off
Circuit
1
2
4
3
1
2
4
3
Opto-isolation
4
3
Equivalent
Relay
Diagram
Opto-isolation
Opto-isolation
Turn-o
Circuit
1
2
34
6
5
Opto-isolation
1
2
6
4
Equivalent
Relay
Diagram
Vo
Turn-o
Circuit
1
2
34
6
5
Opto-isolation
Turn-off
Circuit
1
2
3
4
6
5
Opto-isolation
1
2
4 and 6
5
Equivalent
Relay
Diagram
Vo
+
-
Broadcom AV02-0260EN
4
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
ASSR-3220
Package Outline Drawings
ASSR-3210 4-Pin Small Outline Package
Opto-isolation
1
2
3
4
8
7
6
5
1
2
8
7
3
4
6
5
Equivalent
Opto-isolation
Circuit
Relay
Diagram
Turn-off
Circuit
Turn-off
DIMENSIONS IN MILLIMETERS AND [INCHES]
OPTION NUMBER 500 AND UL RECOGNITION NOT MARKED
0.46
0.018
0.5
0.02
0.5
0.02
2.0±0.2
0.079±0.009
0.102±0.102
0.004±0.004
0.20
0.008
4.3 ±0.2
0.169±0.008
2.54
0.100
4.40±0.20
0.173±0.008
0.41
0.016
6.8±0.4
0.268±0.016
TYPE NUMBER
DATE CODE
LEAD FREE
0.80
0.031
2.540
0.10
4.80
0.189
1.20
0.047
0.375
0.015
YWW
xxxx
LAND PATTERN RECOMMENDATION
Broadcom AV02-0260EN
5
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
ASSR-3211 6-Pin DIP Package
ASSR-3211 6-Pin DIP Package with Gull Wing Surface Mount Option 300
9.40 (0.370)
9.90 (0.390)
PIN
ONE
DOT
A XXXX
YYWW
TYPE
NUMBER
DATE CODE
2.16 (0.085)
2.54 (0.100) 2.28 (0.090)
2.80 (0.110)
(0.020)
(0.040)
0.45 (0.018)
0.65 (0.025)
4.70 (0.185) MAX.
2.66 (0.105) MIN.
6.10 (0.240)
6.60 (0.260)
0.20 (0.008)
0.33 (0.013)
TYP.
7.36 (0.290)
7.88 (0.310)
DIMENSIONS IN MILLIMETERS AND (INCHES).
56
321
1.78 (0.070) MAX.
R
U
4
UL
RECOGNITION
LEAD FREE
5°
Broadcom AV02-0260EN
6
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
ASSR-3220 8-Pin DIP Package
1.080 ± 0.320
(0.043 ± 0.013) 2.54 ± 0.25
(0.100 ± 0.010)
0.51 (0.020) MIN.
0.65 (0.025) MAX.
4.70 (0.185) MAX.
2.92 (0.115) MIN.
5qTYP. 0.254 + 0.076
- 0.051
(0.010+ 0.003)
- 0.002)
7.62 ± 0.25
(0.300 ± 0.010)
6.35 ± 0.25
(0.250 ± 0.010)
9.65 ± 0.25
(0.380 ± 0.010)
1.78 (0.070) MAX.
1.19 (0.047) MAX.
A XXXX
YYWW
DATE CODE
DIMENSIONS IN MILLIMETERS AND (INCHES).
5678
4321
OPTION CODE*
UL
RECOGNITION
UR
TYPE NUMBER
OPTION NUMBERS 300 AND 500 NOT MARKED.
3.56 ± 0.13
(0.140 ± 0.005)
LEAD FREE
Broadcom AV02-0260EN
7
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
ASSR-3220 8-Pin DIP Package with Gull Wing Surface Mount Option 300
0.635 ± 0.25
(0.025 ± 0.010) 12qNOM.
9.65 ± 0.25
(0.380 ± 0.010)
0.635 ± 0.130
(0.025 ± 0.005)
7.62 ± 0.25
(0.300 ± 0.010)
5
6
7
8
4
3
2
1
9.65 ± 0.25
(0.380 ± 0.010)
6.350 ± 0.25
(0.250 ± 0.010)
1.016 (0.040)
1.27 (0.050)
10.9 (0.430)
2.0 (0.080)
LAND PATTERN RECOMMENDATION
1.080 ± 0.320
(0.043 ± 0.013)
3.56 ± 0.13
(0.140 ± 0.005)
1.780
(0.070)
MAX.
1.19
(0.047)
MAX.
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
0.254 + 0.076
- 0.051
(0.010 + 0.003)
- 0.002)
Broadcom AV02-0260EN
8
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Lead Free IR Profile
Non-halide flux should be used.
Regulatory Information
The ASSR-3210, ASSR-3211, and ASSR-3220 are approved by the following organizations:
UL
Approved under UL 1577, component recognition program up to VISO = 3750 Vrms.
CSA
Approved under CSA Component Acceptance Notice #5.
Insulation and Safety Related Specifications
Parameter Symbol ASSR-3210
ASSR-3211
ASSR-3220 Unit Conditions
Minimum External Air Gap
(Clearance)
L(101) 4.9 7.1 mm Measured from input terminals to output
terminals, shortest distance through air.
Minimum External Tracking
(Creepage)
L(102) 4.9 7.4 mm Measured from input terminals to output
terminals, shortest distance path along body.
Minimum Internal Plastic Gap
(Internal Clearance)
0.08 0.08 mm Through insulation distance conductor to
conductor, usually the straight line distance
thickness between the emitter and detector.
Tracking Resistance
(Comparative Tracking Index)
CTI 175 175 V DIN IEC 112/VDE 0303 Part 1.
Isolation Group
(DIN VDE0109)
IIIa IIIa Material Group (DIN VDE 0109).
217qC
RAMP-DOWN
6qC/SEC. MAX.
RAMP-UP
3qC/SEC. MAX.
150 - 200qC
260 +0/-5qC
t 25qC to PEAK
60 to 150 SEC.
20-40 SEC.
TIME WITHIN 5q
C of ACTUAL
PEAK TEMPERATURE
tp
ts
PREHEAT
60 to 180 SEC.
tL
TL
Tsmax
Tsmin
25
Tp
TIME (SECONDS)
TEMPERATURE (qC)
NOTES:
THE TIME FROM 25qC to PEAK TEMPERATURE = 8 MINUTES MAX.
Tsmax = 200qC, Tsmin = 150qC
Broadcom AV02-0260EN
9
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Absolute Maximum Ratings
Recommended Operating Conditions
Parameter Symbol Min. Max. Unit Note
Storage Temperature TS–55 125 °C
Operating Temperature TA–40 85 °C
Junction Temperature TJ—125°C
Lead Soldering Cycle Temperature — 260 °C
Time — 10 s
Input Current Average IF—25mA
Surge — 50
Transient — 1000
Reversed Input Voltage VR—5 V
Input Power Dissipation ASSR-3220 PIN —80mW
ASSR-3211,
ASSR-3210
PIN —40mW
Output Power Dissipation ASSR-3220 PO—800mW
ASSR-3211,
ASSR-3210
PO—400mW
Average Output Current
(TA = 25°C, TC ≤ 100°C)
IO—0.2 A a
a. For derating, refer to Figure 1 and Figure 2.
ASSR-3211
Connection B
IO—0.4 A
Output Voltage (TA = 25°C) VO–250 250 V b
b. The voltage across the output terminals of the relay should not exceed this rated withstand voltage. Overvoltage protection circuits should be
added in some applications to protect against overvoltage transients.
ASSR-3211
Connection B
VO0250V b
Solder Reflow Temperature Profile See Lead Free IR Profile.
Parameter Symbol Min. Max. Unit Note
Input Current (ON) IF(ON) 320mA
a
a. Threshold to switch device is IF ≥ 0.5 mA; however, for qualified device performance over temperature range, it is recommended to operate
at IF = 5 mA. See Applications Information.
Input Voltage (OFF) VF(OFF) 00.8V
Operating Temperature TA–40 +85 °C
Broadcom AV02-0260EN
10
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Package Characteristics
Unless otherwise specified, TA = 25°C.
Electrical Specifications (DC)
Over recommended operating TA = –40°C to 85°C, IF = 5 mA to 10 mA, unless otherwise specified.
Parameter Sym. Min. Typ. Max. Unit Conditions Note
Input-Output Momentary
Withstand Voltage
VISO 3750 — — Vrms RH ≤ 50%, t = 1 min. a, b
a. Device is considered a two-terminal device:
ASSR-3210 — pin 1, 2 shorted and pin 3, 4 shorted.
ASSR-3211 — pin 1, 2, 3 shorted and pin 4, 5, 6 shorted.
ASSR-3220 — pin 1, 2, 3, 4 shorted and pin 5, 6, 7, 8 shorted.
b. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating, refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your
equipment level safety specification, or Broadcom Application Note 1074, Optocoupler Input-Output Endurance Voltage.
Input-Output Resistance RI-O —1012 —ΩV
I-O = 500 Vdc
Input-Output Capacitance a
ASSR-3210 CI-O — 0.4 — pF f = 1 MHz; VI-O = 0 Vdc
ASSR-3211 CI-O — 0.5 — pF f = 1 MHz; VI-O = 0 Vdc
ASSR-3220 CI-O — 0.8 — pF f = 1 MHz; VI-O = 0 Vdc
Parameter Sym. Min. Typ. Max. Unit Conditions Figure Note
Output Withstand
Voltage
|VO(OFF)|250280— VV
F = 0.8V, IO = 250 μA, TA = 25°C
230 — — V VF = 0.8V, IO = 250 μA 3
Output Leakage Current IO(OFF) —0.3100nAV
F = 0.8V, VO = 250V, TA = 25°C
—— 1μAV
F = 0.8V, VO = 250V 4
Output Offset Voltage |V(OS)|—1—μVI
F = 5 mA, IO = 0 mA
Input Reverse Breakdown
Voltage
VR5——VI
R = 10 μA
Input Forward Voltage VF1.1 1.3 1.65 V IF = 5 mA 5, 6
Output On-Resistance R(ON) —810ΩI
F = 5 mA, IO = 200 mA,
Pulse ≤ 30 ms, TA = 25°C
7, 8a
a. During the pulsed R(ON) measurement (IO duration ≤ 30 ms), ambient (TA) and case temperature (TC) are equal.
ASSR-3211
Connection B
R(ON) —2.02.5 ΩI
F = 5 mA, IO = 400 mA,
Pulse ≤ 30 ms, TA = 25°C
a
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Broadcom AV02-0260EN
11
Switching Specifications (AC)
Over recommended operating TA = –40°C to 85°C, IF = 5 mA to 10 mA, unless otherwise specified.
Applications Information
On-Resistance and Derating Curves
The Output On-Resistance, R(ON), specified in this data
sheet, is the resistance measured across the output contact
when a pulsed current signal (IO = 0.2A) is applied to the
output pins. The use of a pulsed signal (≤30 ms) implies that
each junction temperature is equal to the ambient and case
temperatures. The steady-state resistance, Rss, on the
other hand, is the value of the resistance measured across
the output contact when a DC current signal is applied to the
output pins for a duration sufficient to reach thermal
equilibrium. Rss includes the effects of the temperature rise
in the device.
Derating curves are shown in Figure 1 and Figure 2,
specifying the maximum output current allowable for a given
ambient temperature. The maximum allowable output
current and power dissipation are related by the expression
Rss = Po(max) / (Io(max))2 from which Rss can be
calculated. Staying within the safe area ensures that the
steady-state MOSFET junction temperature remains less
than 125°C.
Turn On Time and Turn Off Time
Variation
The ASSR-32xx Series exhibits a very fast turn on and turn
off time. Both the turn on and turn off time can be adjusted
by choosing proper forward current as depicted in Figure 9
and Figure 11. The changes of the turn on and turn off time
with ambient temperature are also shown in Figure 10 and
Figure 12.
Parameter Sym. Min. Typ. Max. Unit Conditions Figure Note
Turn On Time TON — 0.25 1.0 ms IF = 5 mA, IO = 200 mA, TA = 25°C9, 13
——2.0msI
F = 5 mA, IO = 200 mA 10
Turn Off Time TOFF — 0.02 0.2 ms IF = 5 mA, IO = 200 mA, TA = 25°C11, 13
——0.5msI
F = 5 mA, IO = 200 mA 12
Output Transient Rejection dVO/dt 1 7 — kV/μs ΔVO = 250V, TA = 25°C14
Input-Output Transient
Rejection
dVI-O/dt 1 ≥10 — kV/μs ΔVI-O= 1000V, TA = 25°C15
Broadcom AV02-0260EN
12
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Figure 1: Maximum Average Output Current Rating vs.
Ambient Temperature
Figure 2: Output Power Derating vs. Case Temperature
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
-40 -20 0 20 40 60 80
100
I
O
- OUTPUT CURRENT - A
TA -TEMPERATURE -
qC
SAFE
OPERATING
AREA
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
70 90 110 130 150
TC - CASE TEMPERATURE - qC
SAFE
OPERATING
AREA
PO - OUPUT POWER DISSIPATION - W
Figure 3: Normalized Typical Output Withstand Voltage vs.
Temperature
Figure 4: Typical Output Leakage Current vs. Temperature
0.9
0.95
1
1.05
1.1
-50 -25 0 25 50 75
100
TA - TEMPERATURE -
q
C
NORMALIZED OUTPUT WITHSTAND VOLTAGE
IO = 250 PA
VF = 0.8V
1.E-12
1.E-11
1.E-10
1.E-09
1.E-08
1.E-07
-50 -25 0 25 50 75
100
TA
- TEMPERATURE -
q
C
I
o(OFF)
- OUTPUT CURRENT - A
Figure 5: Typical Forward Voltage vs. Temperature Figure 6: Typical Forward Current vs. Forward Voltage
1
1.1
1.2
1.3
1.4
1.5
-50 -25 0255075
100
I
F
=10mA
I
F
=5mA
V
F
- FORWARD VOLTAGE - V
T
A
- TEMPERATURE -
qC
3
4
5
6
7
8
9
10
0.4 0.8 1.2 1.6
VF - FORWARD VOLTAGE - V
I
F
- FORWARD CURRENT - mA
TA = -40qC
TA = 0qC
TA = 25qC
TA = 85qC
Broadcom AV02-0260EN
13
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Figure 7: Typical On Resistance vs.Temperature Figure 8: Typical Output Current vs. Output Voltage
4
6
8
10
12
14
16
-50 0 50 100 150
200
T
A
- TEMPERATURE -
qC
R
ON
- ON RESISTANCE - :
IF = 10mA
IF = 5mA
-0.2
-0.1
0
0.1
0.2
-2 -1 0 1 2
VO - OUTPUT VOLTAGE - V
I
O
- OUTPUT CURRENT - A
TA= -40
qC
TA= 25
qC
TA= 85
qC
Figure 9: Typical Turn On Time vs. Input Current Figure 10: Typical Turn On Time vs. Temperature
0
100
200
300
400
500
600
700
0 5 10 15 20
TON - TURN ON TIME - μS
I
F (ON)
- INPUT CURRENT - mA
150
200
250
300
350
400
450
-40 -20 0 20 40 60 80 100
I
F
= 5mA
T
ON
- TURN ON TIME - Ps
T
A
- TEMPERATURE -
q
C
Figure 11: Typical Turn Off Time vs. Input Current Figure 12: Typical Turn Off Time vs. Temperature
0
10
20
30
40
50
60
70
0 5 10 15 20
T
OFF
- TURN OFF TIME -
P
S
I
F(ON)
- INPUT CURRENT - mA
0
10
20
30
40
50
-40 -20 0 20 40 60 80 100
T
OFF
- TURN OFF TIME - PS
T
A
-
TEMPERATURE -
qC
I
F
= 5mA
Broadcom AV02-0260EN
14
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Figure 13: Switching Test Circuit for tON, tOFF
INPUT
IF
OUTPUT
Vo
10%
tON
PULSE GEN.
Zo = 50
tf = tr = 5ns
INPUT
M
ONITORING
NODE
OUTPUT Vo
MONITORING
NODE
IF
CL*
RL
( *CL IS APPROXIMATELY 25pF WHICH
INCLUDES PROBE AND STRAY WIRIN
G
CAPACITANCE)
VDD
R
200ohm
tOFF
90%
50%
50%
P.W. = 15 ms
1
2
8
7
3
4
6
5
ASSR-3220
Broadcom AV02-0260EN
15
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Figure 14: Output Transient Rejection Test Circuit
PULSE GEN.
Zo = 50
+
ASSR-3220
1
2
8
7
3
4
6
5
OUTPUT Vo
MONITORIN
G
NODE
CMRM
C
M
INCLUDES PROBE AND FIXTURE CAPACITANCE
R
M
INCLUDES PROBE AND FIXTURE RESISTANCE
V PEAK
t
R
VPEAK
90%
10%
t
F
90%
10%
IN
PUT OPEN
VO (MAX) < 3V
F
PEAK
R
PE AK
t
V
OR
t
V
dt
dV )8.0()8.0(
0
=
OVER SHOOT ON V
PEAK
IS TO BE 10%
Broadcom AV02-0260EN
16
ASSR-3210, ASSR-3211, ASSR-3220 Data Sheet
General-Purpose, Form A, Solid State Relay
(Photo MOSFET) (250V/0.2A/10Ω)
Figure 15: Input-Output Transient Rejection Test Circuit
I
F
PULSE GEN.
Zo = 50
V
FF
A
B
+
SWITCH AT POSITION "B": I
F
= 5 mA
1
2
8
7
3
4
6
5
OUTPUT Vo
MONITORING
NODE
CL*
RL = 1kohm
( *C
L
IS APPROXIMATELY 25pF WHICH
INCLUDES PROBE AND STRAY WIRI
NG
CAPACITANCE)
V
DD
= 5V
V
I-O
+
tR
V
I-O(PEAK)
90%
10%
tF
90%
10%
S
WITCH AT POSITION "A": I
F
= 0 mA V
O(OFF)
(min.) > 4V
V
O(OFF)
V
O(ON)
V
O(ON)
(max.) < 0.8V
ASSR-3220
Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, and the A logo are among the trademarks
of Broadcom and/or its affiliates in the United States, certain other countries and/or the EU.
Copyright © 2012–2017 by Broadcom. All Rights Reserved.
The term “Broadcom” refers to Broadcom Limited and/or its subsidiaries. For more information, please visit
www.broadcom.com.
Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability,
function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does
not assume any liability arising out of the application or use of this information, nor the application or use of any product or
circuit described herein, neither does it convey any license under its patent rights nor the rights of others.