FEP16AT THRU FEP16JT FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 600 Volts Forward Current - 16.0 Amperes TO-220AB FEATURES 0.185 (4.70) 0.175 (4.44) 0.154 (3.91) 0.415 (10.54) MAX. 0.055 (1.27) DIA. 0.148 (3.74) 0.045 (1.14) 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 0.560 (14.22) 0.530 (13.46) 0.410 (10.41) 0.390 (9.91) 0.350 (8.89) 0.635 (16.13) 0.330 (8.38) 0.625 (15.87) 1 PIN 2 1.148 (29.16) 3 1.118 (28.40) 0.110 (2.79) 0.100 (2.54) 0.160 (4.06) 0.140 (3.56) Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Dual rectifier construction, positive centertap Glass passivated chip junctions Low power loss Low forward voltage, high current capability High surge current capability Superfast recovery times for high efficiency High temperature soldering guaranteed: 250C, 0.16" (4.06mm) from case for 10 seconds 0.560 (14.22) 0.530 (13.46) MECHANICAL DATA 0.105 (2.67) 0.095 (2.41) 0.037 (0.94) 0.027 (0.68) 0.105 (2.67) 0.095 (2.41) Case: JEDEC TO-220AB molded plastic body over passivated chips Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 5 in. - lbs. max. Weight: 0.08 ounce, 2.24 grams 0.016 (0.41) 0.014 (0.35) 0.205 (5.20) 0.195 (4.95) PIN 1 PIN 2 PIN 3 CASE Dimensions are in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25C ambient temperature unless otherwise specified. FEP SYMBOLS 16AT FEP 16BT FEP 16CT FEP 16DT FEP 16FT FEP 16GT FEP 16HT FEP 16JT UNITS Maximum repetitive peak reverse voltage VRRM 50 100 150 200 300 400 500 600 Volts Maximum RMS voltage VRMS 35 70 105 140 210 280 350 420 Volts Maximum DC blocking voltage VDC 50 100 150 200 300 400 500 600 Volts Maximum average forward rectified current at TC=100C I(AV) 16.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 200.0 Amps Maximum instantaneous forward voltage per leg at 8.0A VF Maximum DC reverse current at rated DC blocking voltage per leg IR TC=25C TC=100C Maximum reverse recovery time (NOTE 1) per leg trr Typical Junction Capacitance per leg (NOTE 2) CJ Typical thermal resistance (NOTE 3) Operating junction and storage temperature range 0.95 1.3 1.5 10.0 500.0 35.0 A 50.0 85.0 Volts ns 60.0 pF RJA RJC 15.0 2.2 C/W TJ, TSTG -55 to +150 C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient and from junction to case per leg mounted on heatsink RATINGS AND CHARACTERISTICS CURVES FEP16AT THRU FEP16JT FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 20 RESISTIVE OR INDUCTIVE LOAD 16 12 8.0 4.0 0 0 50 100 150 CASE TEMPERATURE, C 300 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 250 200 150 100 50 0 1 10 100 NUMBER OF CYCLES AT 60 HZ FIG. 4 -TYPICAL REVERSE CHARACTERISTICS PER LEG 100 40 50-400V 500-600V 10 TJ=125C PULSE WIDTH=300s 1% DUTY CYCLE 1 TJ=25C 50-400V 300-400V 500-600V 0.1 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 10 5C 12 TJ= 00C TJ=1 1 0.1 TJ=25C 0.01 0 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG JUNCTION CAPACITANCE, pF 1,000 TJ=125C f=1.0 MHZ Vsig=50mVp-p 100 50-400V 500-600V 10 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 100