SIDACtor (R) Protection Thyristors SLIC Protection Battrax(R) Series - Single Port Negative - MS-013 Description The Battrax(R) series offers programmable SIDACtor(R) overvoltage protection devices for SLIC applications. The Single Port Negative Battrax Series provides a programmable device that is referenced to a negative voltage souce while internal diodes provide protection from positive surge events. Features and Benefits * Single-port protection * Low on-state voltage * Gate triggered tracking device * Does not degrade with use Agency Approvals Agency * Low voltage overshoot * Fails short circuit when surged in excess of ratings Agency File Number E133083 * Integrated diodes for positive voltage Applicable Global Standards Pinout Designation * TIA-968-A * GR 1089 Intra-building * TIA-968-B * IEC 61000-4-5 5 * ITU K.20/21 Enhanced Level * YD/T 1082 4 * ITU K.20/21 Basic Level * YD/T 950 1 6 2 3 * YD/T 993 * GR 1089 Inter-building Schematic Symbol 6 (No Connect) (T) 1 (-VREF) 2 5 (G) 4 (No Connect) (R) 3 Electrical Characteristics Part Number Marking VDRM @lDRM=5A VS @100V/s V min V max IH IS mA min mA max IT VT @IT=2.2 Amps VF A max V max V max Capacitance* pF min pF max B1101UALxx B1101UA I-VREFI + I-1.2VI I-VREFI + I-10VI 100 100 2.2 4 5 30 200 B1161UALxx B1161UA I-VREFI + I-1.2VI I-VREFI + I-10VI 160 100 2.2 4 5 30 200 B1201UALxx B1201UA I-VREFI + I-1.2VI I-VREFI + I-10VI 200 100 2.2 4 5 30 200 B1101UCLxx B1101UC I-VREFI + I-1.2VI I-VREFI + I-10VI 100 100 2.2 4 5 30 200 B1161UCLxx B1161UC I-VREFI + I-1.2VI I-VREFI + I-10VI 160 100 2.2 4 5 30 200 B1201UCLxx B1201UC I-VREFI + I-1.2VI I-VREFI + I-10VI 200 100 2.2 4 5 30 200 - VREF Max Value for the negative Battrax is -200 V. - XX = Part Number Suffix: `TP' (Tube Pack) or `RP' (Reel Pack). Notes: - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). - Devices are uni-directional - All electrical characteristics shown are defined from Tip (pin 1) to Ground (pin 5), and Ring (pin 3) to Ground (pin 5) (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. * Off-state capacitance (CO) is measured across pins 1 & 5 and 3 & 5 at 1 MHz with a 2V bias. 118 Revised: September 30, 2011 SIDACtor (R) Protection Thyristors SLIC Protection Surge Ratings Series IPP 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 ITSM 50/60 Hz di/dt A min A min A min A min A min A min A min A min A min A min A/s max A 20 150 150 90 50 75 75 45 75 20 500 C 50 500 400 200 150 200 175 100 200 50 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40C to +85C (IPP rating assumes VREF equals +/- 48 V) - The device must initially be in thermal equilibrium with -40C < TJ < +150C 1 Current waveform in s 2 Voltage waveform in s Thermal Considerations Package Symbol Modified MS-013 6 5 4 Parameter Value Unit TJ Operating Junction Temperature Range -40 to +125 C TS Storage Temperature Range -65 to +150 C 60 C/W 1 2 R0JA 3 Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform IPP - Peak Pulse Current - %IPP +I V VREF VS VDRM IF VT -V IDRM +V IH IS IT IPP -I Waveform = tr x td 50 Half Value 0 0 PIN 3 CONNECTED TO VREF td tr t - Time (s) Normalized DC Holding Current vs. Case Temperature Normalized VS Change vs. Junction Temperature 10 IH 8 6 25 C 4 2 IH (TC = 25C) 2.0 14 12 Ratio of Percent of VS Change - % 100 PIN CONNECTED TO GROUND Pin51-2: PIN TOGROUND VREF PIN22CONNECTED CONNECTED TO tr = rise time to peak value td = decay time to half value Peak Value 0 -4 -6 -8 -40 -20 0 1.6 1.4 1.0 0.8 0.6 -40 Junction Temperature (TJ) - C 25C 1.2 0.4 20 40 60 80 100 120 140 160 (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 1.8 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 119 Revised: September 30, 2011 SIDACtor (R) Protection Thyristors SLIC Protection Soldering Parameters Pb-Free assembly (see Fig. 1) +150C +200C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3C/sec. Max. TS(max) to TL - Ramp-up Rate 3C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)C Time within 5C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6C/sec. Max. Time 25C to Peak Temp (TP) 8 min. Max. Do not exceed +260C Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25C to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VREF Max. (VDC Peak ) +125C or +150C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65C to +150C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65C, 1008 hrs. Thermal Shock 0C to +100C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85C, 168 hrs., 3 reflow cycles (+260C Peak). JEDEC-J-STD-020, Level 1 Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Battrax Series Positive MS-013 Part Numbering.eps For pg. 131 MS-013 Part Marking Drawing_2009-03-05.eps Part Numbering Part Marking B1 xx 1 U x L xx TYPE B1: Negative Battrax SIDACtor HOLDING CURRENT 10: 100 mA 20: 200 mA 16: 160 mA CONSTRUCTION VARIABLE (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. PACKING OPTIONS RP: Reel Pack TP: Tube Pack XXXXXXX RoHS COMPLIANT Part Marking Code (Refer to Electrical Characteristics Table) Date Code IPP RATING XXXXX PACKAGE TYPE 120 Revised: September 30, 2011 SIDACtor (R) Protection Thyristors SLIC Protection Dimensions -- MS-013 Dimensions 0.065 (1.65) Pad Outline C 0.460 (11.68) 0.138 (3.50) D 7 TYP J 7 TYP A Dimension are in inches (and millimeters). 0.059 (1.50) E G Burr Side H 96 A Mold Split Line 4 A 7 TYP BSC* F MIN Length of Flat 7 TYP Detail A K B A B C D E F G H J K BSC* Inches Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 * BSC = Basic Spacing between Centers Packing Options Package Type U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 6-pin Tube Pack 500 (50 per tube) TP N/A Tape and Reel Specification -- MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification -- MS-013 Message Location .045 (1.14) .310 (7.87) 90 6 Interior of the Tube .165 (4.19) .150 (3.81) .225 (5.72) .020 .005 WALL TYP. (0.51 0.13) .108 (2.74) .005 A .110 (2.79) A Dimensions are in inches (and millimeters) .525 (13.34) (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 121 Revised: September 30, 2011 Millimeters 20.000 .030 (508.00 0.76) 3.63