Roundline Plus Stainless Steel Actuators 5/16" to 3" bore Single and Double acting actuators Full range of bore sizes All essential models Optional Ecology seal Technical data Medium: Filtered, lubricated or nonlubricated, compressed air Maximum Operating Pressure: 250 psig (17.2 bar) Temperature Range*: Standard Nitrile Seals: -20 to 200F (-29 to 93C) High temp Seals: -20 to 400F (-29 to 205C) ACTUATORS *With dew point of supply air less than air temperature below 35F (2C) Lubrication: All Roundline Plus cylinders are pre-lubricated during assembly with a Teflon(R) based grease for non-lube service and long life. Materials Cylinder Body: 304 Stainless Steel Head and Cap: Aluminum Alloy Piston Rod: Stainless steel in double rod cylinders, and 5/16", 7/16", and 9/16" bores. Chrome plated steel in all other bore sizes Rod Bearing: Oil Impregnated Sintered Bronze Piston: Aluminum Alloy or stainless steel Rod & Piston Seals: Nitrile Pivot Bracket, Rod Clevis, Foot Bracket, Mounting Nut: Bright Zinc Plated Carbon Steel ACT-106 Options selector RP 075 x 2.50 - DAN - PS Series Roundline Plus Roundline Plus with Ecology seals* Mounting Options Adjustable Cushion Head End Adjustable Cushion Cap End Adjustable Cushion Both Ends Bumpers (not available with HT) Alternate Port Location Side Ported End Cap (DAN and SAN models only, note length adder) Magnetic Piston Switch Rail and location RP *ERP Bore Size 5/16" 031 7/16" 043 9/16" 056 3/4" (E) 075 7/8" 087 1-1/16" (E) 106 1-1/4" (E) 125 1-1/2" (E) 150 1-3/4" 175 2" (E) 200 2-1/2" (E) 250 3" (E) 300 E - Available with Ecology Seals Stroke Increments of 1/16" up to a maximum. See table Mounting Options Single Acting Nose Single Acting Pivot Single Acting Front Block Single Acting Rear Block Single Acting Front Trunnion Single Acting Rear Trunnion Single Acting Non-Rotating Nose Single Acting Non-Rotating Pivot Reverse Acting Nose Reverse Acting Pivot Reverse Acting Front Block (available in 3/4" & 1-1/16" only) Reverse Acting Rear Block Double Acting Nose Double Acting Pivot Double Acting Double End Mount Double Acting Front Block Double Acting Rear Block Double Acting Front Trunnion Double Acting Rear Trunnion Double Acting Double Rod End SAN SAP SBF SBR STF STR NRN NRP RAN RAP RAF RAR DAN DAP DAD DAF DAR DFT DRT DRD Non-Adjustable cushion head end Non-Adjustable cushion cap end Non-Adjustable cushions both ends No Flats (no plain rod stick out) No Rod Thread Pivot Bushing (no pin) Non-Standard Male Thread Non-Standard Female Thread Thread extension over standard (specify additional length) Rod extension over standard (specify additional length) Stainless Steel piston rod (standard on certain models) High Temperature Seals Rod Wiper (not available with HT) CH CC CB UB PL(__) PC PS M1,M2, M3,M4 NH* NC* NB* NF** PR PO TM(__) FT(__) TX(__) RX(__) SS HT RW * ERP, ecology cylinders come complete with nonadjustable cushions both ends (NH, NC, NB, options not required in model number of ERP cylinder). ERP on DAP, DAD, and DAN models only (add PC option length adder to DAN models) ** Available only on 1-1/16" bore - RAN and RAP, mounts. Male thread extension only. Consult factory for negative thread or rod extensions. Maximum Stroke Lengths Bore Single & Reverse Acting Double Acting 5/16" 4 12 7/16"-9/16" 6 36 3/4"-1-3/4" 6 36 2" 4 36 2-1/2"-3" 36 Consult factory for longer stroke lengths. www.norgren.com/info/US-ACT-106 Roundline Plus Stainless Steel Actuators 1 Oil impregnated sintered bronze Rod Bearing provides exceptional rod support, and optimal cycle life 5 Solid aluminum Piston is strong yet lightweight for low inertia 2 Chrome plated carbon steel Piston Rod for strength, smooth operation, and long life (stainless steel Piston Rod on 5/16, 7/16, 9/16 and all Double Rod cylinders) 6 Lip-type nitrile Piston Seals are wear compensating for long life 7 3 Lip-Type nitrile Rod Seal, pressure energized and wear compensating 304 stainless steel Cylinder Body with polished I.D. ensures smooth performance and outstanding life cycle 4 Head and Cap are solid aluminum alloy for strength and durability 1 6 5 3 4 7 2 4 *Note: Single acting cylinders (not shown) use springs manufactured from music wire to provide millions of trouble free cycles. Ecology Roundline Plus - ERP Model 1 2 IMPACT DAMPENING ECOLOGY PISTON SEALS Increased load capabilities and cycle rates Vibration and noise reduction ACTUATORS The ERP model is the cost effective answer to load deceleration and faster through cushion performance. 2 1 PRE-ENGINEERED NON-ADJUSTABLE CUSHION Tamper resistant Increased performance Roundline Ecology Piston Seal Option (ERP) The Ecology (Impact Dampening) Piston Seal option is available on select inch bore size Roundline cylinders in DAP, DAD, and DAN configurations. This option includes non-adjustable air cushions on both the extend and retract stroke of the cylinder. By including the Ecology Piston Seal option, cylinders can be specified based on weights of load being carried and speed of load. This is shown in the table below. Energy Absorption Capacity of the Impact Dampening Piston Seal This chart represents the energy absorption capacity of the Impact Dampening piston seals with standard Non-Adjustable air cushions. The values given are usable pounds stoppable at stated piston speeds. In/Sec 6 12 18 24 30 36 42 48 54 60 3/4 36.6 5.6 2.5 1.4 0.9 0.6 0.5 0.3 0.3 0.2 1-1/16 62.3 15.6 6.9 3.9 2.5 1.7 1.3 1.0 0.8 0.6 Cylinder Bore 1-1/4 74.5 18.6 8.3 4.7 3.0 2.1 1.5 1.2 0.9 0.7 1-1/2 115.5 28.9 12.8 7.2 4.6 3.2 2.4 1.8 1.4 1.2 2 258.9 64.7 28.8 16.2 10.4 7.2 5.3 4.0 3.2 2.6 2-1/2 421.1 105.3 46.8 26.3 16.8 11.7 8.6 6.6 5.2 4.2 PSI 0 20 40 60 80 100 Effect of Impact Dampening Seals on Total Stroke of Cylinders Cylinder Bore 3/4 1-1/16 1-1/4 1-1/2 2 .11 .12 .12 .14 .15 .08 .09 .09 .10 .10 .05 .06 .06 .07 .07 .03 .04 .04 .04 .04 .01 .02 .02 .02 .02 0 0 0 0 0 2-1/2 .17 .12 .08 .05 .02 0 The figure above represents total stroke loss (both ends) for the pressure indicated for new cylinders. The impact dampening seals will take some compression set during operation of the cylinder and the stroke loss will decrease. To determine stroke loss for either head or cap divide the value shown by 2. ACT-107 Roundline Plus Stainless Steel Actuators Dimensions in inches Option Combination Availability Chart ERP (prefix) ACTUATORS ERP (prefix) CH CC CB UB PL(__) PC PS M1,M2, M,M4 NH NC NB PR PO TM(__) FT(__) TX(__) RX(__) SS HT RW CH CC x x x x x x x x x x x x CB UB x x x x x x x x x x x x x = Option combination available M1,M2, PL(__) PC PS M,M4 NH x x x x Force Factor Data Bore Code x x x x x x X = Option combination not available NC NB x x x x PR PO TM(__) FT(__) TX(__) RX(__) x x x x x x x x x x x x x x x x x x x x SS HT RW x x x Air Reservoir Force Factor (Area) Extend Retract 0.077 0.064 0.15 0.12 0.25 0.22 0.44 0.39 0.6 0.55 0.89 0.61 1.23 1.08 1.77 1.62 2.41 2.21 3.14 2.84 4.91 4.61 7.07 6.63 5/16" (031) 7/16" (043) 9/16" (056) 3/4" (075) 7/8" (087) 1-1/16" (106) 1-1/4" (125) 1-1/2" (150) 1-3/4" (175) 2" (200) 2-1/2" (250) 3" (300) Force Output Formula Cylinder Output Force = Force Factor (area) x Air Line Pressure (psi) Ex: 1-1/16 bore cylinder operating at 80 psi: Force exerted on the extend: 0.89 x 80 = 71.2 lbs. Force exerted on the retract: 0.69 x 80 = 55.2 lbs. Air Reservoirs are made of the same high-quality stainless steel as the Series RP Cylinders. LB PLUS LENGTH K K E J Approximate Spring Forces (lbs.) Bore 5/16" 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" 2" Code (031) (043) (056) (075) (087) (106) (125) (150) (175) (200) Relaxed (lbs) 0.5 1 2 3 3 3 7.5 7 11 15 Compressed (lbs) 1 2 4 6 6 6 15 14 24 30 EE NPT (Both Ends) Dimensions -- All Dimensions in Inches Bore 3/4" 1-1/16" 1-1/2" 2" 2-1/2" E EE J K LB 0.813 1.125 1.562 2.080 2.610 1/8" 1/8" 1/8" 1/4" 1/4" 0.625 0.875 0.875 1.250 1.750 0.187 0.187 0.250 0.312 0.312 1.938 2.375 2.250 2.875 2.875 Standard Internal Lengths 1" increments thru 4" 1" increments thru 8" 1" increments thru 16" 1" increments thru 16" 1" increments thru 24" How to Order Example: 1-1/16" bore air reservoir with a 3" internal length would be ordered as follows: AR-1-1/16 x 3 ACT-108 www.norgren.com/info/US-ACT-108 Roundline Plus Stainless Steel Actuators UB - Bumpers Bumpers are standard on 5/16", 7/8", 1-1/4", and 1-3/4" bores - when the HT high temperature option is ordered, the bumpers are omitted and the overall length may decrease (except 5/16" bore). Single acting models will have one bumper on the piston side opposite the spring. (see chart for changes in overall length due to bumper, or bumper omission.) NOTE: Bumpers are not included with the Ecology Seal model. Increase in cylinder length due to the UB option Single Reverse Double Double Acting Acting Acting Rod End Std Std Std Std 0.062 0.125 0.188 0.25 0.062 0.062 0.125 0.125 0.125 0.125 0 0 Std Std Std Std 0.125 0.125 0.125 0.5* Std Std Std Std 0.125 0.125 0.125 0.125 Std Std Std Std 0.125 0.125 0.250 0.250 0.125 0.125 0.250 0.250 0.125 0.125 0.250 0.250 Bore 5/16" 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" 2" 2-1/2" 3" * When the UB and PS options are in combination on an 1-1/16" bore, double rod end, only the bumper length should be added. All other models and bore sizes should add the UB length and the PS length together. HT - High Temperature Seals For service up to 400F. Not available with RW rod wiper option. When ordered with the UB bumper option, cylinder will only be rated to 200F - as this is the temperature limitation of the bumpers. For cylinders where bumpers are standard, opting for High Temperature seals will omit the bumpers and may decrease the overall length of the cylinder (except the 5/16" bore). See below for length changes. Bore 5/16" 7/8" 1-1/4" 1-3/4" PC - Side ported end cap (DAN and SAN models only) Port will be on the side of the end cap and in line with the head end port. Overall length of the cylinder will increase. Change in overall length due to the PC option. Bore 5/16" 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" 2" 2-1/2" 3" Length Increase 0.2 0.19 0.03 0.44 0.28 0.25 0.31 0.19 0.56 0.38 0.38 0.44 PS - Magnetic Piston A magnet on the piston may increase the length of the cylinder. See chart below for length adders. Increase in cylinder length with the PS option Single & Double Double Acting Rod End Reverse Acting 5/16" 0.150 0.150 N/A 7/16" 0.200 0.250 0.250 9/16" 0.125 0 0 3/4" 0.125 0 0 7/8" 0.125 0.125 0.125 1-1/16" 0.125 0 0.125** 1-1/4" 0.125 0 0 1-1/2" 0.125 0 0 1-3/4" 0.125 0 0 2" 0.125 0 0 2-1/2" 0 0 3" 0 0 * When the UB and PS options are in combination on an 1-1/16" bore, double rod end, only the bumper length should be added. All other models and bore sizes should add the UB length and the PS length together. ** Ecology piston seal adds .375" to the overall length when combined with PS option on the 1-1/16" bore DRD model only. Bore Decrease in Overall length due to HT option (in.) Single Reverse Double Double Acting Acting Acting Rod End 0.000 0.000 0.000 0.000 0.090 0.125 0.220 0.250 0.125 0.125 0.190 0.250 0.125 0.125 0.250 0.250 PL(__) - Alternate Port Location Designate location on head and cap respectively. For example: L(12) = Head port location 1, and Cap port location 2. 1 4 2 3 Rail shown at position M2 M1,M2,M3,M4 - Switch rail mounted and position Switch rail will be mounted in position #1 for M1 option, Position #2 for M2 option, etc. Must also reference the PS option in the cylinder model number to receive a magnet on the piston. A band style swtich bracket can be ordered as a separate item instead of the switch rail. See switch section for band style bracket information. Switches ordered as separate items. FT(__) - Female thread Specify thread type in parentheses. Female rod thread available on 1-3/4", 2", 2-1/2", 3" bores. ACT-109 ACTUATORS CH,CC,CB - Adjustable Cushions Available only on DAN, DAP, and DAD models. Roundline Plus Stainless Steel Actuators Dimensions in inches Single Acting Spring Return (SAN) -- Nose Mount KK Piston Rod Threads MM Dia. Piston Rod TOTAL LENGTH A C G ACTUATORS A 0.38 0.50 0.50 0.50 0.50 0.50 0.75 0.75 0.88 0.88 C N/A N/A N/A N/A N/A N/A 0.25 0.25 0.31 0.38 D N/A N/A N/A N/A N/A N/A 0.38 0.38 0.44 0.50 E 0.36 0.50 0.62 0.81 0.94 1.12 1.34 1.56 1.84 2.08 E J D Across Wrench Flats Bore 5/16" 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" 2" K RM Pilot V EE Port N1 Mounting Nut EE 10-32 10-32 10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT G 0.25 0.31 0.38 0.44 0.50 0.50 0.63 0.63 0.75 0.81 J N/A 0.38 0.50 0.62 0.62 0.88 0.88 0.88 1.25 1.25 K N/A 0.19 0.19 0.19 0.19 0.19 0.25 0.25 0.25 0.31 KK 5-40 10-32 10-32 1/4-28 1/4-28 5/16-24 7/16-20 7/16-20 1/2-20 1/2-20 MM 0.125 0.187 0.187 0.250 0.250 0.312 0.437 0.437 0.500 0.625 N1 1/4-28 3/8-24 7/16-20 1/2-20 5/8-18 5/8-18 3/4-16 3/4-16 1-14 1-1/4-12 RM .309/.312 .369/.373 .434/.437 .494/.498 .621/.624 .621/.624 .746/.749 .746/.749 1.029/1.032 1.372/1.375 V 0.03 0.05 0.06 0.08 0.09 0.07 0.09 0.09 0.09 0.12 Total Length 1.12 + (0.75 per 1/2" of stroke) 1.31 + (0.94 per 1/2" of stroke) 1.53 + (1.62 per 1" of stroke) 1.50 + (1.69 per 1" of stroke) 1.84 + (1.56 per 1" of stroke) 1.94 + (1.56 per 1" of stroke) 2.66 + (1.81 per 1" of stroke) 2.44 + (1.69 per 1" of stroke) 2.97 + (2.00 per 1" of stroke Consult Factory Single Acting Spring Return (SAP) -- Pivot Mount TOTAL LENGTH A KK Piston Rod Threads G FL RM Pilot C V CB M EE Port MM Dia. Piston Rod D Across Wrench Flats Bore 5/16 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" 2" A 0.38 0.50 0.50 0.50 0.50 0.50 0.75 0.75 0.88 0.88 CB 0.25 0.31 0.31 0.38 0.38 0.38 0.50 0.62 0.62 0.75 C N/A N/A N/A N/A N/A 0.12 0.25 0.25 0.31 0.38 CD 0.125 0.156 0.156 0.250 0.250 0.250 0.250 0.375 0.375 0.375 ACT-110 D N/A N/A N/A N/A N/A 0.25 0.38 0.38 0.44 0.50 E1 0.36 0.50 0.62 0.81 0.94 1.12 1.34 1.56 1.84 2.08 E2 0.36 0.74 0.62 0.86 0.94 1.12 1.34 1.56 1.84 2.08 EE 10-32 10-32 10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT L E1 Dia. E2 Dia. N1 Mounting Threads FL 0.34 0.44 0.38 0.62 0.62 0.62 0.78 0.81 1.12 1.03 G 0.25 0.31 0.38 0.44 0.50 0.50 0.63 0.63 1.06 0.81 KK 5-40 10-32 10-32 1/4-28 1/4-28 5/16-24 7/16-20 7/16-20 1/2-20 1/2-20 L 0.19 0.25 0.25 0.34 0.34 0.34 0.41 0.50 0.50 0.56 LH N/A 0.50 N/A 0.75 0.75 0.75 N/A N/A N/A N/A CD Dia. PIN LH N2 Mounting Threads M 0.16 0.25 0.19 0.28 0.28 0.28 0.40 0.38 0.50 0.44 MM 0.125 0.187 0.187 0.250 0.250 0.312 0.437 0.437 0.500 0.625 N1 1/4-28 3/8-24 7/16-20 1/2-20 5/8-18 5/8-18 3/4-16 3/4-16 1-14 1-1/4-12 N2 3/8-24 7/16-20 7/16-20 5/8-18 5/8-18 5/8-18 3/4-16 3/4-16 1-14 1-1/4-12 V 0.03 0.05 0.06 0.08 0.09 0.07 0.09 0.09 0.09 0.12 RM .245/.249 .369/.373 .434/.437 .494/.498 .621/.624 .621/.624 .746/.749 .746/.749 1.029/1.032 1.372/1.375 Total Length 1.52 + (.75 per 1/2" of stroke) 1.75 + (.94 per 1/2" of stroke) 1.81 + (1.62 per 1" of stroke) 2.28 + (1.69 per 1" of stroke) 2.47 + (1.56 per 1" of stroke) 2.66 + (1.56 per 1" of stroke) 3.38 + (1.81 per 1" of stroke) 3.12 + (1.69 per 1" of stroke) 4.03 + (2.00 [per 1" of stroke) Consult Factory www.norgren.com/info/US-ACT-110 Roundline Plus Stainless Steel Actuators Dimensions in inches Single Acting Spring Return (SBF) -- Front Block Mount TOTAL LENGTH E1 SQ KK Piston A Rod C Threads RM Pilot K DB Thds C'Bore for SB Sockets Head Cap Screw (2) V MM Dia. Piston Rod E2 7/16" BORE ONLY J RT Threads BC Bolt Circle (2) Bore 7/16" 3/4" 1-1/16" 1-1/2" A 0.50 0.75 0.75 1.25 BC 0.75 1.00 1.25 1.75 C N/A 0.25 0.38 0.25 D Across Wrench Flats DN D N/A 0.22 0.25 0.38 DB 8-32 1/4-20 1/4-20 5/16-18 DN N/A 0.62 0.81 1.12 E1 0.75 1.00 1.25 1.75 .31 EE Port H E2 0.50 0.81 1.12 1.56 EE 10-32 1/8 NPT 1/8 NPT 1/4 NPT H N/A 0.38 0.62 0.88 J 0.38 0.62 0.88 0.88 K 0.19 0.19 0.19 0.25 KK 10-32 1/4-28 5/16-24 7/16-20 MM 0.187 0.250 0.312 0.437 RM 0.44 0.63 0.75 1.00 .44 .44 RT 8-32 10-32 10-32 1/4-20 SB N/A #10 #10 1/4 V 0.06 0.09 0.09 0.13 Total Length 1.94 + (.94 per 1/2" of stroke) 2.66 + (1.69 per 1" of stroke) 3.38 + (1.81 per 1" of stroke) 3.69 + (2.00 per 1" of stroke) Single Acting Spring Return (SBR) -- Rear Block Mount A G Y RM Pilot C E2 SQ 2 V MM Dia. Piston Rod D Across Wrench Flats E1 Dia. EE Port RT Threads BC Bolt Circle (2) N1 Mounting Threads Bore 7/16" 3/4" 1-1/16" 1-1/2" A 0.50 0.75 0.75 1.25 BC 0.75 1.00 1.25 1.75 C N/A 0.25 0.25 0.25 D N/A 0.22 0.25 0.38 E1 0.50 0.81 1.12 1.56 E2 0.75 1.00 1.25 1.75 EE 10-32 1/8 NPT 1/8 NPT 1/8 NPT G 0.31 0.44 0.50 0.63 KK 10-32 1/4-28 5/16-24 7/16-20 MM 0.187 0.250 0.312 0.437 N1 3/8-24 1/2-20 5/8-18 3/4-16 RM .369/.373 .494/.498 .621/.624 .746/.749 RT 8-32 10-32 10-32 1/4-20 V 0.05 0.08 0.07 0.09 Y2 0.34 0.44 0.44 0.62 Total Length 1.62 + (0.94 per 1/2" of stroke) 2.31 + (1.69 per 1" of stroke) 2.81 + (1.81 per 1" of stroke) 3.06 + (2.00 per 1" of stroke) Single Acting Spring Return (STF) -- Front Trunnion Mount TOTAL LENGTH KK Piston A Rod C Threads E1 SQ K E2 V TW RM TH MM Dia. Piston Rod J D Across Wrench Flats EE Port TL TD Bore 7/16" 3/4" 1-1/16" 1-1/2" A 0.50 0.75 0.75 1.25 C N/A 0.25 0.25 0.25 D N/A 0.22 0.25 0.38 E1 0.75 1.00 1.25 1.75 E2 0.50 0.81 1.12 1.56 EE 10-32 1/8 NPT 1/8 NPT 1/8 NPT J 0.38 0.62 0.88 0.88 K 0.19 0.19 0.19 0.25 KK 10-32 1/4-28 5/16-24 7/16-20 MM 0.187 0.250 0.312 0.437 RM 0.44 0.62 0.75 1.00 TD 0.37 0.50 0.50 0.50 TH 0.25 0.38 0.38 0.38 TL 0.31 0.69 1.09 1.31 TW 1.25 1.75 2.00 2.50 V 0.05 0.09 0.09 0.12 Total Length 1.94 + (0.94 per 1/2" of stroke) 2.66 + (1.69 per 1" of stroke) 3.38 + (1.81 per 1" of stroke) 3.69 + (2.00 per 1" of stroke) ACT-111 ACTUATORS TOTAL LENGTH KK Piston Rod Threads Roundline Plus Stainless Steel Actuators Dimensions in inches Single Acting Spring Return (STR) -- Rear Trunion Mount E2 SQ TD TOTAL LENGTH KK Piston Rod Threads A G TL TA RM Pilot C V MM Dia. Piston Rod TW D Across Wrench Flats E1 Dia. EE Port TH N1 Mounting Threads Bore 7/16" 3/4" 1-1/16" 1-1/2" A 0.50 0.75 0.75 1.25 C N/A 0.25 0.25 0.25 D N/A 0.22 0.25 0.38 E1 0.50 0.81 1.12 1.56 E2 0.75 1.00 1.25 1.75 EE 10-32 1/8 NPT 1/8 NPT 1/8 NPT G 0.31 0.69 0.75 0.88 KK 10-32 1/4-28 5/16-24 7/16-20 MM 0.187 0.250 0.312 0.437 N1 3/8-24 1/2-20 5/8-18 3/4-16 RM .370/.375 .494/.498 .621/.624 .746/.749 TA 0.09 0.06 0.06 0.12 TD 0.37 0.50 0.50 0.50 TH 0.25 0.38 0.38 0.38 TL 0.25 0.38 0.38 0.50 TW 1.25 1.75 2.00 2.50 V 0.05 0.08 0.07 0.06 Total Length 1.62 + (0.94 per 1/2" of stroke) 2.31 + (1.69 per 1" of stroke) 2.81 + (1.81 per 1" of stroke) 3.06+ (2.00 per 1" of stroke) Single Acting Non-Rotating (NRN) -- Nose Mount TOTAL LENGTH ACTUATORS KK Piston Rod Threads A K G C E RM Pilot V MM Hex Piston Rod J EE Port N1 Mounting Nut Bore 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" A 0.50 0.50 0.50 0.50 0.50 0.88 0.88 0.88 C 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.38 E 0.50 0.62 0.81 0.94 1.12 1.34 1.56 1.84 EE 10-32 10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT G 0.31 0.38 0.44 0.50 0.50 0.63 0.63 0.74 J 0.38 0.50 0.62 0.62 0.88 0.88 0.88 1.25 K 0.19 0.19 0.19 0.19 0.19 0.25 0.25 0.25 KK 10-32 10-32 1/4-28 1/4-28 5/16-24 7/16-20 7/16-20 1/2-20 MM (hex) 0.187 0.187 0.250 0.250 0.375 0.437 0.437 0.500 N1 3/8-24 7/16-20 1/2-20 5/8-18 5/8-18 3/4-16 3/4-16 1-14 RM .369/.373 .434/.437 .494/.498 .621/.624 .621/.624 .746/.749 .746/.749 1.029/1.032 V 0.05 0.06 0.08 0.09 0.07 0.09 0.09 0.09 Total Length 1.56 + (.94 per 1/2" of stroke) 1.78 + (1.62 per 1" of stroke 1.75 + (1.69 per 1" of stroke) 2.09 + (1.56 per 1" of stroke) 2.19 + (1.56 per 1" of stroke) 2.66 + (1.81 per 1" of stroke) 2.44 + (1.69 per 1" of stroke) 3.03 + (2.00 per 1" of stroke) Single Acting Non-Rotating (NRP) -- Pivot Mount KK Piston Rod Threads A G C TOTAL LENGTH RM Pilot EE Port V FL M CB MM Hex Piston Rod E1 Dia. E2 Dia. N1 Mounting Threads Bore 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" A 0.50 0.50 0.50 0.50 0.50 0.88 0.88 0.88 C 0.25 0.25 0.25 0.25 0.25 0.25 0.38 0.38 CB 0.31 0.31 0.38 0.38 0.38 0.50 0.62 0.62 CD 0.156 0.156 0.250 0.250 0.250 0.250 0.375 0.375 ACT-112 E1 0.50 0.62 0.81 0.94 1.12 1.34 1.56 1.84 E2 0.74 0.62 0.86 0.94 1.12 1.34 1.56 1.84 EE 10-32 10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT FL 0.44 0.38 0.62 0.62 0.62 0.78 0.81 1.12 G 0.31 0.38 0.44 0.50 0.50 0.63 0.63 0.74 KK 10-32 10-32 1/4-28 1/4-28 5/16-24 7/16-20 7/16-20 1/2-20 L 0.25 0.25 0.34 0.34 0.34 0.41 0.50 0.50 LH 0.50 N/A 0.75 0.75 0.75 0.88 1.00 N/A M 0.25 0.19 0.28 0.28 0.28 0.40 0.37 0.50 L CD Dia. Pin LH N2 Mounting Thds. MM (hex) 0.187 0.187 0.250 0.250 0.375 0.437 0.437 0.500 N1 3/8-24 7/16-20 1/2-20 5/8-18 5/8-18 3/4-16 3/4-16 1-14 N2 7/16-20 7/16-20 5/8-18 5/8-18 5/8-18 3/4-16 3/4-16 1-14 RM .369/.373 .434/.437 .494/.498 .621/.624 .621/.624 .746/.749 .746/.749 1.029/1.032 V 0.05 0.06 0.08 0.09 0.07 0.09 0.09 0.09 Total Length 2.25 + (.94 per 1/2" of stroke) 2.06 + (1.62 per 1" of stroke) 2.53 + (1.69 per 1" of stroke) 2.72 + (1.56 per 1" of stroke) 2.78 + (1.56 per 1" of stroke) 3.38 + (1.81 per 1" of stroke) 3.25 + (1.69 per 1" of stroke) 4.09 + (2.00 per 1" of stroke) www.norgren.com/info/US-ACT-112 Roundline Plus Stainless Steel Actuators Dimensions in inches Reverse Acting Spring Extend (RAN) -- Nose Mount TOTAL LENGTH A KK Piston Rod Threads Y EE Port G C RM Pilot V MM Dia. Piston Rod D Across Wrench Fltas E1 Dia. E2 Dia. N1 Mounting Nut A 0.38 0.50 0.50 0.50 0.50 0.50 0.75 1.25 0.88 0.88 C N/A N/A N/A N/A N/A 0.12 0.25 0.25 0.31 0.38 D N/A N/A N/A N/A N/A 0.25 0.38 0.38 0.44 0.50 E1 0.61 0.74 0.62 0.86 0.94 1.12 1.34 1.56 1.84 2.08 E2 0.36 0.50 0.62 0.81 0.94 1.12 1.34 1.56 1.84 2.08 EE 10-32 10-32 10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT G 0.31 0.38 0.38 0.50 0.50 0.50 0.63 0.63 0.75 0.81 KK 5-40 10-32 10-32 1/4-28 1/4-28 5/16-24 7/16-20 7/16-20 1/2-20 1/2-20 MM 0.125 0.187 0.187 0.250 0.250 0.312 0.437 0.437 0.500 0.625 N1 3/8-24 7/16-20 7/16-20 5/8-18 5/8-18 5/8-18 3/4-16 3/4-16 1-14 1-1/4-12 RM .371/.373 .434/.437 .434/.437 .621/.624 .621/.624 .621/.624 .746/.749 .746/.749 1.029/1.032 1.372/1.375 V 0.03 0.05 0.06 0.09 0.09 0.09 0.09 0.09 0.09 0.12 Y 0.47 0.72 0.75 0.97 0.97 1.06 1.37 1.25 1.62 1.46 Total Length 1.49 + (1.25 per 1/2" of stroke) 1.94 + (1.44 per 1/2" of stroke) 2.00 + (2.62 per 1" of stroke) 2.31 + (2.69 per 1" of stroke) 2.31 + (2.56 per 1" of stroke) 2.62 + (2.81 per 1" of stroke) 3.47 + (2.81 per 1" of stroke) 3.19 + (3.00 per 1" of stroke) 4.03 + (3.00 per 1" of stroke) Consult Factory ACTUATORS Bore 5/16" 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" 2" Reverse Acting Spring Extend (RAP) -- Pivot Mount KK Piston Rod Threads TOTAL LENGTH. Y A G E EE Port V CB M C MM Dia. Piston Rod D Across Wrench Flats Bore 5/16" 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 2" A 0.38 0.50 0.50 0.50 0.50 0.50 0.75 1.25 0.88 C N/A N/A N/A N/A N/A 0.12 0.25 0.25 0.38 CB 0.25 0.31 0.31 0.38 0.38 0.38 0.50 0.62 0.75 CD 0.125 0.156 0.156 0.250 0.250 0.250 0.250 0.375 0.375 D N/A N/A N/A N/A N/A 0.25 0.38 0.38 0.50 EE 10-32 10-32 10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT N1 Mounting Threads RM Pilot E 0.61 0.74 0.62 0.86 0.94 1.12 1.34 1.56 2.08 G 0.31 0.38 0.38 0.50 0.50 0.50 0.63 0.63 0.81 KK 5-40 10-32 10-32 1/4-28 1/4-28 5/16-24 7/16-20 7/16-20 1/2-20 L 0.19 0.25 0.25 0.34 0.34 0.34 0.34 0.50 0.56 LH N/A 0.50 0.50 0.75 0.75 0.75 0.88 1.00 1.63 MM 0.125 0.187 0.187 0.250 0.250 0.312 0.437 0.437 0.625 M 0.16 0.25 0.19 0.28 0.28 0.28 0.38 0.38 0.44 L N1 3/8-24 7/16-20 7/16-20 5/8-18 5/8-18 5/8-18 3/4-16 3/4-16 1-1/4-12 CD Dia. PIN RM .371/.373 .434/.437 .434/.437 .621/.624 .621/.624 .621/.624 .746/.749 .746/.749 1.372/1.375 V 0.03 0.05 0.06 0.09 0.09 0.09 0.09 0.09 0.12 LH Y 0.47 0.72 0.75 0.97 0.97 1.06 1.37 1.25 1.46 Total Length 1.88 + (1.25 per 1/2" of stroke) 2.38 + (1.44 per 1/2" of stroke) 2.28 + (2.62 per 1" of stroke) 2.44 + (2.69 per 1" of stroke) 2.62 + (2.56 per 1" of stroke) 2.78 + (2.81 per 1" of stroke) 3.78 + (2.81 per 1" of stroke) 3.88 + (3.00 per 1" of stroke) Consult Factory ACT-113 Roundline Plus Stainless Steel Actuators Dimensions in inches Reverse Acting Spring (RAF) -- Front Block Mount Total Length E1 SQ L RM Pilot A MM Dia. Piston Rod ACTUATORS Bore 3/4" 1-1/16" 1-1/2" A 0.75 0.75 1.25 C 0.25 0.25 0.25 D 0.22 0.25 0.38 DB 1/4-20 1/4-20 5/16-18 V C D Across Wrench Flats KK Piston Rod Threads RT Threads BC Bolt Circle (2) DN Y H DN 0.63 0.81 1.12 E2 DB Thds C'Bore for SB Socket Head Cap Screw (2) SB 10-32 10-32 0.25 E1 1.00 1.25 1.75 E2 0.81 1.12 1.56 EE 1/8 NPT 1/8 NPT 1/4 NPT H 0.38 0.62 0.88 EE PORT KK 1/4-28 5/16-24 7/16-20 L 0.34 0.47 0.38 MM 0.250 0.312 0.437 RM 0.62 0.75 1.00 RT 10-32 10.32 1/4-20 BC 1.00 1.25 1.75 V 0.09 0.07 0.12 Y 0.5 0.54 0.65 Total Length 2.56 + (2.69 per 1" of stroke) 3.12 + (2.81 per 1" of stroke) 3.69 + (3.00 per 1" of stroke) Reverse Acting Spring (RAR) -- Rear Block Mount KK Piston Rod Threads TOTAL LENGTH. Y A G E2 SQ EE Port V C MM Dia. Piston Rod D Across Wrench Flats Bore 3/4" 1-1/16" 1-1/2" A 0.75 0.75 1.25 C 0.25 0.25 0.25 D 0.22 0.25 0.38 E1 0.86 1.12 1.56 ACT-114 E2 1.00 1.25 1.75 N1 Mounting Threads EE 1/8 NPT 1/8 NPT 1/4 NPT G 0.50 0.50 0.62 KK 1/4-28 5/16-24 7/16-20 MM 0.250 0.312 0.437 E1 Dia. N1 5/8-18 5/8-18 3/4-16 RM Pilot RM .621/.624 .621/.624 .746/.749 RT 10-32 10-32 1/4-20 RT Threads BC Bolt Circle (2) BC 1.00 1.25 1.75 V 0.09 0.09 0.09 Y 0.97 1.06 1.25 Total Length 3.22 + (2.69 per 1" of stroke) 3.53 + (2.81 per 1" of stroke) 3.88 + (3.00 per 1" of stroke) www.norgren.com/info/US-ACT-114 Roundline Plus Stainless Steel Actuators Dimensions in inches Double Acting (DAN) -- Nose Mount LB + STROKE KK Piston Rod Threads A Y EE Port RM Pilot G C K V MM Dia. Rod Piston J E1 Dia. Bore 5/16" 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" 2" 2-1/2" 3" A 0.38 0.50 0.50 0.50 0.50 0.50 0.75 0.75 0.88 0.88 0.88 1.25 C N/A N/A N/A N/A N/A N/A 0.25 0.25 0.31 0.38 0.38 0.38 D N/A N/A N/A N/A N/A N/A 0.38 0.38 0.44 0.50 0.50 0.63 EE 10-32 10-32 10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT 1/4 NPT 3/8 NPT E1 0.61 0.74 0.62 0.86 0.94 1.12 1.34 1.56 1.84 2.08 2.62 3.12 E2 0.36 0.50 0.62 0.81 0.94 1.12 1.34 1.56 1.84 2.08 2.62 3.12 G 0.31 0.38 0.38 0.50 0.50 0.50 0.63 0.63 0.75 0.81 0.81 1.00 J 0.36 0.38 0.50 0.62 0.62 0.88 0.88 0.88 1.25 1.25 1.75 2.00 EE Port E2 Dia. N1 Mounting Nut K N/A 0.19 0.19 0.19 0.19 0.19 0.25 0.25 0.25 0.31 0.31 0.31 KK 5-40 10-32 10-32 1/4-28 1/4-28 5/16-24 7/16-20 7/16-20 1/2-20 1/2-20 1/2-20 5/8-18 LB 1.64 2.12 2.28 2.97 2.94 3.12 4.00 3.69 4.69 4.69 4.69 5.25 MM 0.125 0.187 0.187 0.250 0.250 0.312 0.437 0.437 0.500 0.625 0.625 0.750 N1 3/8-24 7/16-20 7/16-20 5/8-18 5/8-18 5/8-18 3/4-16 3/4-16 1-14 1-1/4-12 1-3/8-12 1-1/2-12 RM .371/.373 .434/.437 .434/.437 .621/.624 .621/.624 .621/.624 .746/.749 .746/.749 1.029/1.032 1.372/1.375 1.497/1.500 1.622/1.625 Y 0.47 0.72 0.75 0.97 0.97 1.06 1.37 1.25 1.63 1.46 1.46 1.71 V 0.03 0.05 0.06 0.09 0.09 0.09 0.09 0.09 0.09 0.12 0.12 0.19 ACTUATORS D Across Wrench Flats Double Acting (DAP) -- Pivot Mount KK Piston Rod Threads A C G LB + STROKE Y E FL EE Port CB V MM Dia. Piston Rod D Across Wrench Flats Bore 5/16" 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" 2" 2-1/2" 3" A 0.38 0.50 0.50 0.50 0.50 0.50 0.75 0.75 0.88 0.88 0.88 1.25 C N/A N/A N/A N/A N/A 0.12 0.25 0.25 0.31 0.38 0.38 0.38 CB 0.25 0.31 0.31 0.38 0.38 0.38 0.50 0.62 0.62 0.75 0.75 0.88 RM Pilot N1 Mounting Threads XD + STROKE CD 0.125 0.156 0.156 0.250 0.250 0.250 0.250 0.375 0.376 0.375 0.375 0.500 D N/A N/A N/A N/A N/A 0.25 0.38 0.38 0.44 0.50 0.50 0.63 E 0.61 0.74 0.62 0.86 0.94 1.12 1.34 1.56 1.84 2.08 2.62 3.12 EE 10-32 10-32 10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT 1/4 NPT 3/8 NPT FL 0.34 0.44 0.38 0.62 0.62 0.62 0.78 0.81 1.12 1.03 1.03 1.34 CD Dia. PIN L LH N2 Mounting Threads G 0.31 0.38 0.38 0.50 0.50 0.50 0.63 0.63 0.75 0.81 0.81 1.00 KK 5-40 10-32 10-32 1/4-28 1/4-28 5/16-24 7/16-20 7/16-20 1/2-20 1/2-20 1/2-20 5/8-18 L 0.19 0.25 0.25 0.34 0.34 0.34 0.41 0.50 0.50 0.56 0.56 0.81 LB 2.19 2.81 2.75 4.03 3.84 4.12 5.12 4.75 6.25 6.06 6.06 7.12 LH 0.39 0.50 0.50 0.75 0.75 0.75 0.88 1.00 N/A 1.63 1.63 N/A MM 0.125 0.187 0.187 0.250 0.250 0.312 0.437 0.437 0.500 0.625 0.625 0.750 N1 3/8-24 7/16-20 7/16-20 5/8-18 5/8-18 5/8-18 3/4-16 3/4-16 1-14 1-1/4-12 1-3/8-12 1-1/2-12 N2 3/8-24 7/16-20 7/16-20 5/8-18 5/8-18 5/8-18 3/4-16 3/4-16 1-14 1-1/4-12 1-3/8-12 1-1/2-12 RM .371/.373 .434/.437 .434/.437 .621/.624 .621/.624 .621/.624 .746/.749 .746/.749 1.029/1.032 1.372/1.375 1.497/1.500 1.622/1.625 V 0.03 0.05 0.06 0.09 0.09 0.09 0.09 0.09 0.09 0.12 0.12 0.19 XD 2.03 2.56 2.56 3.75 3.56 3.84 4.72 4.38 5.75 5.62 5.62 6.50 Y 0.47 0.72 0.75 0.97 0.97 1.07 1.37 1.25 1.63 1.54 1.47 1.71 ACT-115 Roundline Plus Stainless Steel Actuators Dimensions in inches Double Acting (DAD) -- Double End Mount LB + STROKE A KK Piston Rod Threads Y2 Y1 G K E Dia. C EE Port V V MM Dia. Piston Rod ACTUATORS D Across Wrench Flats Bore 5/16" 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" 2" 2-1/2" 3" A 0.38 0.50 0.50 0.50 0.50 0.50 0.75 0.75 0.88 0.88 0.88 1.25 C N/A N/A N/A N/A N/A 0.12 0.25 0.25 0.31 0.38 0.38 0.38 D N/A N/A N/A N/A N/A 0.25 0.38 0.38 0.44 0.50 0.50 0.63 E 0.61 0.74 0.62 0.86 0.94 1.12 1.34 1.56 1.84 2.08 2.62 3.12 EE 10-32 10-32 10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT 1/4 NPT 3/8 NPT RM Pilot N1 Mounting Nut G 0.31 0.38 0.38 0.50 0.50 0.50 0.63 0.63 0.75 0.81 0.81 1.00 K 0.35 0.50 0.44 0.62 0.62 0.62 0.81 0.62 1.00 1.00 1.00 1.43 KK 5-40 10-32 10-32 1/4-28 1/4-28 5/16-24 7/16-20 7/16-20 1/2-20 1/2-20 1/2-20 5/8-18 LB 2.19 2.81 2.75 4.03 3.84 4.12 5.12 4.75 6.25 6.06 6.06 7.12 MM 0.125 0.187 0.187 0.250 0.250 0.312 0.437 0.437 0.500 0.625 0.625 0.750 N1 3/8-24 7/16-20 7/16-20 5/8-18 5/8-18 5/8-18 3/4-16 3/4-16 1-14 1-1/4-12 1-3/8-12 1-1/2-12 RM .371/.373 .434/.437 .434/.437 .621/.624 .621/.624 .621/.624 .746/.749 .746/.749 1.029/1.032 1.372/1.375 1.497/1.500 1.622/1.625 V 0.03 0.05 0.06 0.09 0.09 0.09 0.09 0.09 0.09 0.12 0.12 0.19 Y1 0.47 0.73 0.75 0.97 0.97 1.07 1.37 1.25 1.63 1.46 1.46 1.71 Y2 0.50 0.69 0.57 0.90 0.90 0.90 1.18 0.94 1.12 1.47 1.47 1.34 5/16" BORE ONLY #10-32 port (Opposite 0.41 Side) Double Acting (DAF) -- Front Block Mount .11 thru (2) holes .34 E1 SQ KK Piston Rod Threads RM Pilot LB + STROKE A K V DN RT Threads BC Bolt Circle (2) BC N/A 0.75 1.00 1.25 1.75 C N/A N/A 0.25 0.38 0.25 H D N/A N/A 0.22 0.25 0.38 ACT-116 DB N/A 8-32 1/4-20 1/4-20 5-16-18 7/16" BORE ONLY .44 J D Across Wrench Flats A 0.38 0.50 0.75 0.75 1.25 E2 DB Thds C'Bore for SB Socket Head Cap Screw (2) C MM Dia. Piston Rod Bore 5/16" 7/16" 3/4" 1-1/16" 1-1/2" 0.59 DN N/A N/A 0.62 0.81 1.12 EE N/A N/A 1/8 NPT 1/8 NPT 1/8 NPT Y E1 0.50 0.75 1.00 1.25 1.75 .44 EE PORT .31 EE PORT E2 0.36 0.50 0.81 1.12 1.56 H N/A N/A 0.38 0.62 0.88 J N/A 0.38 0.62 0.88 0.88 K N/A 0.19 0.19 0.19 0.25 KK 5-40 10-32 1/4-28 5/16-24 7/16-20 LB 1.72 2.12 3.22 3.75 4.19 MM 0.125 0.187 0.250 0.312 0.437 RM N/A 0.437 0.625 0.75 1.00 RT N/A 8-32 10-32 10-32 1/4-20 SB N/A N/A #10 #10 1/4 V N/A 0.06 0.09 0.09 0.13 #10-32 port (Opposite Side) Y N/A N/A 0.50 0.54 0.65 www.norgren.com/info/US-ACT-116 Roundline Plus Stainless Steel Actuators Dimensions in inches Double Acting (DAR) -- Rear Block Mount LB + Stroke E2 SQ Y1 KK Piston Rod Threads A C G Y2 EE Port V MM Dia. Piston Rod D Across Wrench Flats Bore 7/16" 3/4" 1-1/16" 1-1/2" A 0.50 0.75 0.75 1.25 C N/A 0.25 0.38 0.25 D N/A 0.22 0.25 0.38 RM Pilot E1 Dia. N1 Nose Threads E1 0.75 0.86 1.12 1.56 E2 0.75 1.00 1.25 1.75 EE 10-32 1/8 NPT 1/8 NPT 1/4 NPT G 0.38 0.50 0.50 0.63 KK 10-32 1/4-28 5/16-24 7/16-20 LB 2.44 3.78 4.00 4.38 RT Threads BC Bolt Circle (2) MM 0.187 0.250 0.312 0.437 N1 7/16-20 5/8-18 5/8-18 3/4-16 RM .433/.437 .621/.624 .621/.624 .746/.749 RT 8-32 10-32 10-32 1/4-20 BC 0.75 1.00 1.25 1.75 V 0.05 0.09 0.09 0.09 Y1 0.72 0.97 1.06 1.22 Y2 0.34 0.44 1.25 0.62 Double Acting (DFT) -- Front Block Mount LB + Stroke K TP E2 ACTUATORS KK Piston A Rod C Threads E1 SQ V MM Dia. Piston Rod TW RM J D Across Wrench Flats TH Bore 7/16" 3/4" 1-1/16" 1-1/2" A 0.50 0.75 0.75 1.25 C N/A 0.25 0.38 0.25 TD D N/A 0.22 0.25 0.38 E1 0.75 1.00 1.25 1.75 E2 0.50 0.81 1.12 1.56 EE Port EE Port EE 10-32 1/8 NPT 1/8 NPT 1/4 NPT J 0.38 0.62 0.88 0.88 TL K 0.19 0.19 0.19 0.25 KK 10-32 1/4-28 5/16-24 7/16-20 LB 2.12 3.22 3.75 4.19 MM 0.187 0.250 0.312 0.437 RM 0.44 0.62 0.75 1.00 TD 0.374 0.500 0.500 0.500 TH 0.25 0.38 0.38 0.38 TL 0.31 0.69 1.09 1.31 TP 0.41 0.53 0.53 0.59 TW 1.25 1.75 2.00 2.50 V 0.06 0.09 0.09 0.12 TL 0.25 0.38 0.38 0.50 TW 1.25 1.75 2.00 2.50 Double Acting (DRT) -- Rear Trunnion E2 SQ TD LB + Stroke KK Piston Rod Threads Y1 A C TA G TL EE Port V MM Dia. Piston Rod TW D Across Wrench Flats Bore 7/16" 3/4" 1-1/16" 1-1/2" A 0.50 0.75 0.75 1.25 C N/A 0.25 0.38 0.25 D N/A 0.22 0.25 0.38 E1 0.75 0.86 1.12 1.56 E2 0.75 1.00 1.25 1.75 E1 Dia. N1 Nose Threads EE 10-32 1/8 NPT 1/8 NPT 1/4 NPT G 0.38 0.50 0.50 0.63 KK 10-32 1/4-28 5/16-24 7/16-20 RM Pilot LB 2.44 3.78 4.00 4.38 TH MM 0.187 0.250 0.312 0.437 N1 7/16-20 5/8-18 5/8-18 3/4-16 RM .433/.437 .621/.624 .621/.624 .746/.749 TA 0.09 0.06 0.06 0.12 TD 0.374 0.500 0.500 0.500 TH 0.25 0.38 0.38 0.38 V 0.05 0.09 0.07 0.09 ACT-117 Roundline Plus Stainless Steel Actuators Dimensions in inches Double Acting Double Rod End (DRD) -- Double End Mount ZM + 2 x STROKE Y A KK Piston Rod Threads E. Dia. G C EE Port V M Dia. ston od D Across Wrench Flats Bore 7/16" 9/16" 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" 1-3/4" 2" 2-1/2" 3" A 0.50 0.50 0.50 0.50 0.50 0.75 0.75 0.88 0.88 0.88 1.25 RM Pilot N1 Mounting Nut C N/A N/A N/A N/A 0.12 0.25 0.25 0.31 0.38 0.38 0.38 D N/A N/A N/A N/A 0.25 0.38 0.38 0.44 0.50 0.50 0.63 E 0.74 0.62 0.86 0.94 1.12 1.34 1.56 1.84 2.08 2.62 3.12 EE 10-32 10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT 1/4 NPT 3/8 NPT G 0.38 0.38 0.50 0.50 0.50 0.63 0.63 0.75 0.81 0.81 1.00 KK 10-32 10-32 1/4-28 1/4-28 5/16-24 7/16-20 7/16-20 1/2-20 1/2-20 1/2-20 5/8-18 MM 0.187 0.187 0.250 0.250 0.312 0.437 0.437 0.500 0.625 0.625 0.750 N1 7/16-20 7/16-20 5/8-18 5/8-18 5/8-18 3/4-16 3/4-16 1-14 1-1/4-12 1-3/8-12 1-1/2-12 RM .434/.437 .434/.437 .621/.624 .621/.624 .621/.624 .746/.749 .746/.749 1.029/1.032 1.372/1.375 1.497/1.500 1.622/1.625 V 0.05 0.06 0.09 0.09 0.09 0.09 0.09 0.09 0.12 0.12 0.19 Y 0.72 0.75 0.97 0.97 1.06 1.37 1.25 1.94 1.46 1.46 1.71 ZM 2.81 2.94 4.00 3.91 4.00 5.56 5.12 6.56 6.56 6.56 7.31 ACTUATORS * All accessories are clear zinc plated carbon steel Pivot Bracket FL A J A B B G M E BA CD Dia. Part Number A B BA CD DD E PB-1 0.50 0.28 0.50 0.16 0.19 0.75 0.06 F 0.77 0.12 0.56 FL 0.20 PB-2 PB-3 PB-4 PB-5 0.81 1.00 1.13 1.44 0.44 0.62 0.68 0.88 0.75 1.00 1.00 1.25 0.25 0.38 0.38 0.50 0.27 0.27 0.26 0.27 1.12 1.50 1.50 1.75 1.19 1.75 1.75 2.25 0.31 0.38 0.38 0.50 0.12 0.12 0.25 0.25 G 0.19 0.25 0.25 0.25 J M 0.88 1.38 1.38 1.75 DD DD F Bore 7/16", 9/16" 3/4", 7/8", 1-1/16", 1-1/4" 1-1/2" 1-3/4",2", 2-1/2" 3" PB-0 (5/16" bore only) .156 THRU 2 HOLES .625 .13 .19 .387 .41 .130 dia. thru .50 .26 Rod Clevis (Includes Pin & Jam Nut) LH CB Dia. CA L CD CE KK N ACT-118 Bore 5/16" 7/16", 9/16" 3/4", 7/8" 1-1/16" 1-1/4", 1-1/2" 1-3/4, 2", 2-1/2" 3" Part Number RC-0 RC-1 RC-2 RC-3 RC-4 RC-5 RC-6 CA 0.13 0.19 0.25 0.25 0.38 0.38 0.50 CB dia. 0.13 0.19 0.25 0.25 0.38 0.38 0.50 CD 0.56 0.94 1.19 1.19 1.69 1.69 2.75 CE 0.44 0.75 0.94 0.94 1.31 1.31 2.25 CH 0.31 0.38 0.50 0.50 0.75 0.75 1 KK 5-40 10-32 1/4-28 5/16-24 7/16-20 1/2-20 5/8-18 L 0.38 0.56 0.68 0.69 0.94 0.94 1.5 LH 0.5 0.66 0.85 0.85 1.12 1.12 1.41 CHSQ www.norgren.com/info/US-ACT-118 N 0.16 0.12 0.16 0.19 0.25 0.31 0.38 Roundline Plus Stainless Steel Actuators Dimensions in inches Foot Bracket Part Number FB-0S FB-0D FB-1 FB-2 FB-3 Bore J DD F CD Dia. BA E B C FL A A B BA C CD DD E 0.38 0.25 0.75 0.13 0.25 0.13 1.00 5/16"(S) 0.38 0.25 0.75 0.13 0.38 0.13 1.00 5/16"(D) 7/16"(S) 0.62 0.31 1.00 0.12 0.38 0.19 1.38 7/16"(D), 9/16"(S/D) 0.69 0.38 1.00 0.12 0.44 0.19 1.38 3/4"(S) 0.75 0.44 1.25 0.19 0.50 0.19 1.62 3/4"(D), 7/8"(S/D), 1-1/16"(S/D) FB-4 1.00 0.56 1.50 0.25 0.62 0.27 1.88 1-1/4"(S/D), FB-5 1.50 0.75 1.88 0.62 0.75 0.28 2.50 1-1/2"(S/D) 1-3/4"(S/D) FB-5A 1.50 0.88 2.25 0.75 1.03 0.34 3.00 2"(S/D) FB-6 1.62 1.00 2.25 0.62 1.38 0.34 3.12 2-1/2"(D) FB-7 1.62 1.00 2.88 0.75 1.50 0.34 3.75 3"(D) FB-8 1.62 1.00 3.50 0.89 1.63 0.34 4.38 D = Double Acting Models S/D = Single and Double Acting Models S = Single Acting Models F 0.06 0.06 0.07 0.09 0.10 FL 0.44 0.44 0.56 0.56 0.69 J 0.75 0.75 0.88 0.83 1.09 0.12 0.81 1.38 0.12 0.19 0.25 0.25 0.26 1.75 2.13 2.50 3.00 3.14 1.00 1.25 1.50 1.75 1.89 B Trunnion Bracket A DD Dia. thru 4 holes B F BA E .38 rad. ACTUATORS A CD dia. thru FL J M G Bore 7/16" 3/4", 1-1/16", 1-1/2" Part number PB-4 TB-1 A 1.13 1.13 B 0.69 0.69 BA 1.00 1.00 CD 0.38 0.50 DD 0.27 0.27 E 1.50 1.50 F 0.25 0.25 FL 1.75 1.75 G 0.25 0.25 J 1.38 1.38 M 0.38 0.38 Mounting Nut E HEX Bore T N Threads 5/16" 7/16" 9/16" 3/4" 7/8", 1-1/16" 1-1/4", 1-1/2" 1-3/4" 2" Single Acting Spring Return Models Part Number N E T MN-0 1/4-28 0.44 0.16 MN-1 3/8-24 0.56 0.22 MN-2 7/16-20 0.69 0.25 MN-3 1/2-20 0.75 0.31 MN-4 5/8-18 0.94 0.38 MN-5 3/4-16 1.12 0.42 MN-5A 1-14 1.50 0.55 MN-6 1-1/4-12 1.88 0.50 Single Acting Spring Extend & Double Acting Models Bore Part Number N E T 5/16" MN-1 3/8-24 0.56 0.22 7/16", 9/16" MN-2 7/16-20 0.69 0.25 3/4", 7/8", 1-1/16" MN-4 5/8-18 0.94 0.38 1-1/4", 1-1/2" MN-5 3/4-16 1.12 0.42 1-3/4" MN-5A 1-14 1.50 0.55 2" MN-6 1-1/4-12 1.88 0.50 2-1/2" MN-7 1-3/8-12 2.00 0.50 3" MN-8 1-1/2-12 2.25 0.50 ACT-119 RT Series Roundline Thrusters 9/16" to 3" bore Composite and Roller Bearings Technical data Medium: Filtered, lubricated or nonlubricated, compressed air Operating Pressure 250 psig (17.2 Bar) Max. Temperature Range: Standard Nitrile seals: -20F to 200F (-29C to 93C) High Temp seals: -20F to 400F (-29C to 205C) ACTUATORS *With dew point of supply air less than air temperature below 35F (2C) Lubrication: All Roundline Thruster cylinders are prelubricated at the time of assembly with a Teflon(R)-Based grease, for non-lube service and long life. Thruster Materials: Guide Shafts: 303 stainless steel chrome plated carbon steel 2-1/2" & 3.0" bore case hardend carbon steel with roller bearing option Body: Anodized aluminum housing and tooling plate composite guide shaft bearings roller bearings optional Cylinder Materials: 304 Stainless Steel body Aluminum alloy head,cap and piston Oil impregnated sintered bronze rod bearing Chrome Plated carbon steel piston rod, stainless steel piston rod 9/16' bore only Nitrile piston and rod seals Options selector RT 075 C x 4.50 CC Series Roundline Thruster Roundline Cylinder with *Ecology Seals RT ERT* Bore Size 9/16" 3/4" 1-1/16" 1-1/2" 2" 2-1/2" 3" Bearing Type Composite Roller 056 075 106 150 200 250 300 C R Options Stroke Adjustment (Collar & Bumper) Extend Stroke Adjustment (Collar & Bumper) Retract Adjustable Cushion Head End (Extend) Adjustable Cushion Cap End (Retract) Adjustable Cushion Both Ends Non-Adjustable cushion head end (Extend)* Non-Adjustable cushion cap end (Retract)* Non-Adjustable cushions both ends* Magnetic Piston Switch Rail and location External Bumper Extend External Bumper Retract External Bumper Both End Internal Bumpers (not available with HT) Shock Absorber Extend Shock Absorber Retract Shock Absorber Both High Temperature Seals Tapped Mounting Holes Maximum Stroke Lengths ** 6.0" Maximum Stroke 056 12.0" Maximum Stroke 075 12.0" Maximum Stroke 106 12.0" Maximum Stroke 150 12.0" Maximum Stroke 200 12.0" Maximum Stroke 250 12.0" Maximum Stroke 300 * ERT, ecology cylinders come complete with non-adjustable cushions both ends (NH, NC, NB, options not required in model number of ERT cylinder). **Consult factory for longer stroke lengths. Thrusters available Quarter 3, 2008 ACT-120 www.norgren.com/info/US-ACT-120 AE AR CH CC CB NH NC NB PS M1,M3 BE BF BG UB SG SH SJ HT TH RT Series Roundline Thrusters Thruster LB + STROKE B Drill & C'bore for E socket head cap screw (4) plcs J H C L K S Dia. Guide shaft for composite bearing M SS Dia. Guide shaft for roller bearing F Drill & C' bore for E socket head cap screw (4) places G Bore 9/16" 3/4" 1-1/16" 1-1/2" 2.0" 2-1/2" 3.0" Code 056 075 106 150 200 250 300 A 2.50 3.00 4.25 5.50 6.00 7.50 9.00 B 0.90 1.15 1.75 2.25 2.75 3.25 4.00 C 0.60 0.75 1.00 1.50 2.00 2.25 2.75 D 1.25 1.50 2.00 3.00 3.00 3.75 4.50 E #8 #10 1/4" 5/16" 5/16" 3/8" 1/2" EE #10-32 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT 3/8 NPT EE Port (2) places F 0.63 0.75 1.12 1.25 1.50 1.88 2.25 G 0.45 0.58 0.88 1.12 1.38 1.63 2.00 H 0.38 0.50 0.62 0.75 1.00 1.25 1.50 J 2.25 2.50 3.00 4.00 4.00 6.00 7.00 K 1.25 0.78 0.81 1.12 1.00 1.75 2.00 L 0.75 0.94 1.38 1.75 2.00 2.50 3.00 LB 3.50 4.25 5.00 6.38 7.12 9.75 11.50 M 1.00 1.25 1.88 2.38 2.70 3.50 4.20 S 0.38 0.50 0.62 0.75 0.88 1.13 1.38 SS 0.25 0.38 0.50 0.62 0.75 1.00 1.25 Thrusters available Quarter 3, 2008 ACT-121 ACTUATORS D A RM/59100/C ACTUATORS Miniature Roundline cylinders Single acting, spring return O 2.5 & 4 mm Ideal for very light load applications such as function testing mobile phones and keyboards Low friction characteristics mean high speeds No fittings required - all types feature one integral push on barbed connector Long service life and corrosion resistant materials mean low cost of ownership Technical data Medium: Compressed air, filtered, lubricated or non-lubricated Operating pressure: 50.75 to 101.5 psig (3.5 to 7 bar) Operating temperature: 32F to 140F (0C to 60C) * Air supply must be dry enough to avoid ice formation at temperatures below 35F (2C) Cylinder diameters: 2.5 and 4 mm Strokes: 5, 10 mm - O 2.5 mm 5, 10, 15, 20 mm - O 4 mm Materials Barrel: stainless steel End caps: aluminum alloy Piston rod: stainless steel Elastomers: nitrile Standard strokes Cylinder O mm 2.5 4 Strokes (mm) 5 10 15 20 Options selector R M / 5 9 1 / C / Strokes (mm) Standard strokes only - see `Standard strokes' O 2.5 4 Actuator selection To order a basic 2.5 mm diameter cylinder, sprung in with a 10mm stroke quote: RM/59102/C/10 ACT-122 www.norgren.com/info/US-ACT-122 Substitute 02 04 RM/59100/C Miniature Roundline cylinders Single acting O 2.5 & 4 mm Theoretical forces / Air consumption / Weight of cylinders Theoretical forces N at 6 bar Outstroke F1 2.9 0.7 7.6 1.2 O mm 2.5 4 Air consumption I/cm at 6 bar Instroke Outstroke 0.001 0.001 0.003 0.003 Weight kg by stroke length 5 mm 10 mm 0.002 0.002 0.003 0.004 15 mm - 0.005 20 mm - 0.006 F1 = Return force o1 o 3,5 RM/59102/C/5 RM/59102/C/10 RM/59104/C/5 RM/59104/C/10 RM/59104/C/15 RM/59104/C/20 1,5 B 3,5 5 A O 2.5 2.5 4 4 4 4 A 26.5 35.5 37 46 55 64 B 16.5 25.5 19 28 37 46 3 5 o 3,2 1,6 o5 M4 M2 x 0,4 RM/59104/C 6 4 7 B 5 6 A Note: push-on connector is suitable for 4mm O/D, 2.5 mm I/D polyurethane tubing ACT-123 ACTUATORS 4 1,6 o 3,2 M2,5 x 0,45 Basic dimensions in mm RM/59102/C