IHL0224D09 - XP Power - Product.Network

IHL02 Series DC-DC Converter

Input

Output

Characteristic Minimum Typical maximum Units Notes & Conditions

Output Voltage 3.3 30 VDC See Models and Ratings table

Initial Set Accuracy ±5 % At full load

Minimum Load 10 % Minimum load required to meet specified regulation

Line Regulation ±1.2 %/1% Output changes by max of 1.2% for each 1% change in

input voltage

Load Regulation 12/10 % For IHL0205S3V3 and IHL0205S05/Other Models.

From 10% to full load, see application note

Cross Regulation ±5 % On dual output models, when one output is at 25% load

and other is varied from 10% load to full load

Ripple & Noise 150 mV pk-pk 20 MHz bandwidth. Measured using 10 µF electrolytic in

parallel with 0.1 µF ceramic capacitor

Short Circuit Protection Continuous

Maximum Capacitive Load See Models and Ratings table

Temperature Coefficient 0.03 %/ ˚C

Characteristic Minimum Typical maximum Units Notes & Conditions

Input Voltage Range

4.5 5.5

VDC

5 V nominal

10.8 13.2 12 V nominal

13.5 16.5 15 V nominal

21.6 26.4 24 V nominal

Input Reflected Ripple Current 20 mA pk-pk Through 12 µH inductor and 47 µF capacitor

Input Surge

VDC for 100 ms

5 V nominal

18 12 V nominal

20 15 V nominal

30 24 V nominal

xxx Series

www.xppower.com

• High Isolation, 5200 V

• 250 VAC Working Voltage

• Single and Dual Outputs

• Bipolar Outputs for MOSFET and IGBT Drives

• SIP7 Package

• -40 °C to +95 °C Operation

• Full Load at 65 °C Ambient

• MTBF 2.5 MHrs

• 3 Year Warranty

Dimensions:

IHL02:

0.77 x 0.28 x 0.39” (19.5 x 7.2 x 10.0 mm)

2 Watts

Mechanical Details

Printed

Face

0.28

(7.2)

0.39

(10.0)

0.02

(0.5)

0.02

(0.5)

0.02

(0.5)

0.01

(0.25)

0.08

(2.0)

0.12

(3.0)

0.37

(9.5)

0.08

(2.13)

0.08

(2.13)

0.10 (2.54)

0.60 (15.24)

0.76 (19.5) 0.28

(7.2)

1. All dimensions are in inches (mm)

2. Weight: 0.006 lbs (2.7 g) approx.

3. Pin diameter: 0.02±0.002 (0.5±0.05)

4. Pin pitchand length tolerance: ±0.014 (±0.35)

5. Case tolerance: ±0.02 (±0.5)

Notes

Pin Connections

Pin Single Dual

1 +Vin +Vin

2 -Vin -Vin

5 -Vout -Vout

6 No Pin Common

7 +Vout +Vout

IHL02 Series

www.xppower.com 2

DC-DC Converter

Models & Ratings

Notes

Input currents measured at nominal input voltage.

General

Characteristic Minimum Typical maximum Units Notes & Conditions

Efficiency 80 % See Models and Ratings table

Isolation: Input to Output 5200 VDC

Isolation Working Voltage 250 VAC

Isolation Resistance 109Ω

Isolation Capacitance 7 pF

Switching Frequency 50 100 kHz

Power Density 23.7 W/in3

Mean Time Between Failure 3.3 MHrs MIL-HDBK-217F, +25 °C GB

Weight 0.006 (2.7) lb (g)

Input Voltage Output Voltage Output Current Input current Maximum Capacitive

Load Efficiency Model Number

No Load Full Load

4.5-5.5V

3V3 500 mA 40 mA 435 mA 1000 µF 76% IHL0205S3V3

5 V 400 mA 40 mA 505 mA 470 µF 79% IHL0205S05

9 V 222 mA 40 mA 480 mA 470 µF 83% IHL0205S09

12 V 167 mA 40 mA 475 mA 220 µF 84% IHL0205S12

15 V 133 mA 40 mA 470 mA 220 µF 85% IHL0205S15

±5 V ±200 mA 40 mA 505 mA ±220 µF 79% IHL0205D05

±9 V ±111 mA 40 mA 490 mA ±220 µF 82% IHL0205D09

±12 V ±83.3 mA 40 mA 480 mA ±100 µF 83% IHL0205D12

±15 V ±66.7 mA 40 mA 475 mA ±100 µF 84% IHL0205D15

+15/-9 V +66.7/-111 mA 40 mA 480 mA +100/-220 µF 83% IHL0205D1509

10.8-13.2V

3V3 500 mA 30 mA 185 mA 1000 µF 74% IHL0212S3V3

5 V 400 mA 30 mA 210 mA 470 µF 79% IHL0212S05

9 V 222 mA 30 mA 205 mA 470 µF 82% IHL0212S09

12 V 167 mA 30 mA 205 mA 220 µF 82% IHL0212S12

15 V 133 mA 30 mA 200 mA 220 µF 83% IHL0212S15

±5 V ±200 mA 30 mA 210 mA ±220 µF 79% IHL0212D05

±9 V ±111 mA 30 mA 205 mA ±220 µF 81% IHL0212D09

±12 V ±83.3 mA 30 mA 200 mA ±100 µF 83% IHL0212D12

±15 V ±66.7 mA 30 mA 200 mA ±100 µF 83% IHL0212D15

+15/-9V +66.7/-111 mA 30 mA 210 mA +100/-220 µF 80% IHL0212D1509

13.5-16.5V

3V3 500 mA 25 mA 150 mA 1000 µF 74% IHL0215S3V3

5 V 400 mA 25 mA 170 mA 470 µF 78% IHL0215S05

9 V 222 mA 25 mA 165 mA 470 µF 81% IHL0215S09

12 V 167 mA 25 mA 165 mA 220 µF 82% IHL0215S12

15 V 133 mA 25 mA 160 mA 220 µF 83% IHL0215S15

±5 V ±200 mA 25 mA 170 mA ±220 µF 79% IHL0215D05

±9 V ±111 mA 25 mA 165 mA ±220 µF 81% IHL0215D09

±12 V ±83.3 mA 25 mA 160 mA ±100 µF 83% IHL0215D12

±15 V ±66.7 mA 25 mA 165 mA ±100 µF 82% IHL0215D15

+15/-9V +66.7/-111 mA 25 mA 165 mA +100/-220 µF 81% IHL0215D1509

21.6-26.4V

3V3 500 mA 20 mA 95 mA 1000 µF 73% IHL0224S3V3

5 V 400 mA 20 mA 105 mA 470 µF 78% IHL0224S05

9 V 222 mA 20 mA 105 mA 470 µF 81% IHL0224S09

12 V 167 mA 20 mA 105 mA 220 µF 81% IHL0224S12

15 V 133 mA 20 mA 105 mA 220 µF 81% IHL0224S15

±5 V ±200 mA 20 mA 105 mA ±220 µF 79% IHL0224D05

±9 V ±111 mA 20 mA 105 mA ±220 µF 80% IHL0224D09

±12 V ±83.3 mA 20 mA 105 mA ±100 µF 81% IHL0224D12

±15 V ±66.7 mA 20 mA 100 mA ±100 µF 82% IHL0224D15

+15/-9V +66.7/-111 mA 20 mA 105 mA +100/-220 µF 80% IHL0224D1509

IHL02 Series

www.xppower.com

DC-DC Converter

Mechanical Details

EMC: Immunity

Phenomenon Standard Test Level Criteria Notes & Conditions

ESD Immunity EN61000-4-2 ±6/±8 kV A Contact/Air Discharge

Radiated Immunity EN61000-4-3 10 Vrms A

EFT/Burst EN61000-4-4 2 kV A External components required,

see application notes

Conducted Immunity EN61000-4-6 10 V rms A

magnetic Fields EN61000-4-8 1 A/m A

Printed

Face

0.28

(7.2)

0.39

(10.0)

0.02

(0.5)

0.02

(0.5)

0.02

(0.5)

0.01

(0.25)

0.08

(2.0)

0.12

(3.0)

0.37

(9.5)

0.08

(2.13)

0.08

(2.13)

0.10 (2.54)

0.60 (15.24)

0.76 (19.5) 0.28

(7.2)

1. All dimensions are in inches (mm)

2. Weight: 0.006 lbs (2.7 g) approx.

3. Pin diameter: 0.02±0.002 (0.5±0.05)

4. Pin pitch and length tolerance: ±0.014 (±0.35)

5. Case tolerance: ±0.02 (±0.5)

Notes

Pin Connections

Pin Single Dual

1 +Vin +Vin

2 -Vin -Vin

5 -Vout -Vout

6 No Pin Common

7 +Vout +Vout

EMC: Emissions

Phenomenon Standard Test Level Notes & Conditions

Conducted EN55032 Class B See Application Note

Radiated EN55032 Class B

Environmental

Characteristic Minimum Typical maximum Units Notes & Conditions

Operating Temperature -40 +95 °C Derate Linearly from 100% at 65 °C to no load at 95 °C

Storage Temperature -40 +125 °C

Case Temperature +100 °C

Humidity 2.5 95 %RH Non-condensing

Cooling Natural convection

IHL02 Series

www.xppower.com

DC-DC Converter

23 Aug 16

Input components C1 and D1 are used to help meet EFT and surge test requirements for the module.

Application Note

C1 D1

IHL0205XXXX 330 µF/50 V SMDJ9.0 A

IHL0212XXXX 330 µF/50 V SMDJ13 A

IHL0215XXXX 330 µF/50 V SMDJ18 A

IHL0224XXXX 1000 µF/35 V SMDJ24 A

High limit

ypical Load Line

Low Limit

IHL02

Regulation

EFT Filter

Input filter components (C1,C2, C3 and L) are used to help meet conducted emissions requirements for the module. These components should be

mounted as close as possible to the module, and all leads should be minimised to decrease radiated noise.

C1 L C2 C3

IHL0205XXXX 1206, 4.7 µF/ 16 V 6.8 µH

IHL0212XXXX 1206, 22 µF/ 25 V 6.8 µH

IHL0215XXXX 1206, 22 µF/ 25 V 6.8 µH

IHL0224XXXX 1210, 10 µF/ 35 V 10 µH 1210, 10 µF/ 35 V 1210, 10 µF/ 35 V

IHL02

EMI Filter