SUMMIT 23200A INSTRUMENTS Wide Input Voltage 10 to 75 g Bi-Axial Accelerometers with Signal Conditioning and Temperature Sensor Technical Data* Features and Benefits High Accuracy and Linearity over Wide Temperature Range The voltage output for each axis of the 23200A is directly proportional to the acceleration along that axis. Each DC-coupled output is fully scaled, referenced, and temperature compensated. A force-balanced design improves accuracy by minimizing variations due to temperature and aging effects, resulting in a sensor that is more stable over temperature than piezoelectric or piezoresistive devices. For critical applications, the built-in temperature sensor with very high repeatability can be used to compensate for any residual temperature effects. Calibration Certificate Each 23200A can be supplied with an optional calibration certificate listing gain, offset, and on-axis and transverse alignment parameters needed to ensure rapid and efficient system implementation. The alignment data can be used to compensate the measured values if needed. Self-Test on Digital Command A TTL-compatible self-test input causes a simulated acceleration to be injected into both accelerometers to verify channel integrity. Small Size Complete conditioned bi-axial accelerometer in less than a cubic inch. Built-in Power Supply Regulation A single regulated +5 volt or an unregulated DC power source from +5.25 to +30 volts is all that is required to measure accelerations on both axes. The 23200A is ideal for automotive applications with the ability to survive both continuous reverse battery to -20V and load dump transients to +60V. Easy installation Built-in terminal block or cable with 9-pin connector makes it easy to wire the 23200A. Two through holes and four tapped holes simplify mounting. Suitable for Harsh Environments The 23200A is robust and can be used in harsh environments. The unit will survive 500 g powered and 2000 g unpowered. *Data subject to change without notice Simplify Acceleration and Temperature Measurements The Summit Instruments 23200A accelerometer has two orthogonal axes and a temperature sensor in a small rugged package. The small size and built-in power regulation allow the 23200A to fit where other accelerometers can't. A power source of +5 to +30 VDC is all that is required to measure temperature and 10 g, 15 g, 20 g, 25 g, 30 g, 50 g or 75 g accelerations on each of two axes. When extra precision is required, the high repeatability of the built-in temperature allows precise compensation of temperature effects and alignment data provided on the optional calibration certificate can be used to compensate for transverse sensitivity and alignment errors. Each axial sensor has been tested over the -40 to +85C temperature range. Each axis has a nominal full scale output swing of 2 volts. The zero g output level is nominally +2.5 volts. Precise values for each axis are provided on the optional calibration certificate. Custom versions of the 23200A can be provided for applications which require different ranges and/or bandwidths. Rev. 11/01 Specifications TA = TMIN to TMAX, 5.25 VS 30 V, Acceleration = 0 g, unless otherwise noted. Parameter Range Measurement Full Scale Shock survival, powered Shock survival, unpowered Sensitivity At 25C, 50 g FSR Drift TMIN to TMAX Zero G Bias Level At 25C Drift TMIN to TMAX Alignment Deviation from ideal axes Transverse Sensitivity Nonlinearity Upper Cutoff Frequency Noise Density Amplitude DC to 100 Hz Self Test Input Impedance Temperature Sensor Sensitivity Repeatability Long term drift Absolute error Outputs Output voltage swing Capacitive Drive Capability Power Supply (VS) Input voltage limits Input voltage - operating Input current Rejection Ratio Temperature Range (TA) Mass Scale linearly with range option Rnnn. Min Typical 10 -500 -2000 33.5 40 1 2.1 Max Units Conditions/Notes 75 +500 +2000 g g g On each axis. Must specify via Opt. Rnnn Any axis for 0.5 ms. Recovers on power cycle. Any axis for 0.5 ms. 46 mV/g % 2.9 V g 3.0 degrees % % FSR Hz 1.9 2.0 0.25 0.2 4.6 5000 6.6 66 50 Precise values on Opt. C001 cal certificate. Percent of sensitivity at 25C Precise values on Opt. C001 cal certificate. Repeatable, can be compensated. Precise values on Opt. C001 cal certificate. Can be compensated if required. Inherent sensor error, excluding misalignment. Best fit straight line. -3dB point 10% Must specify via Opt. Bnnn. mg/Hz 4 Hz to 1 kHz mg rms k To ground. Logic "1" 2V, Logic "0" 0.8V Precise values on Opt. C002 cal certificate. mV/K VT at -40C 1.92V ; VT at +85C 3.16V C At 25C after temperature cycle C C 25C offset removed (5C uncorrected) 11.9 8.25 0.1 0.1 3 0.25 1000 4.75 V pF IOUT = 0.1 mA X, Y outputs; T output drives 300pF -20 +5.25 +60 +30 24 V V mA dB C g -20V continuous, >30V if <100ms, duty <1% Continuous or Alt. +5V Regulated Power No load, quiescent. DC. For +5V Regulated: Min 30, Typical 40 Terminal block Opt. T000 rated to -30C Precise values on Opt. C001 cal certificate. 16 120 80 -40 +85 35 Mechanical Connections 1 2 3 4 5 1 2 3 4 5 6 7 8 9 0.167 [4,25] 0.354 [9,00] 0.099 [2,51] 0.323 [8,20] 0.128 [3,25] Dimensions in inches [mm] 0.354 [9,00] 0.542 [13,75] 1.437 [36,50] 0.354 [9,00] 3 mm x 0,5 mm Thread 0.138 [3,50] Deep (4) Places 0.575 [14,60] Y 0.240 [6,10] Y X X 0.689 [17,50] Rear View 1.180 [29,97] 1.000 [25,40] Spring and cable added with Option T001 0.147 [3,73] Thru (2) Places Bottom View Two through holes and four 3 mm x 0.5 mm threaded holes are provided for mounting. Summit Instruments, Inc. 2236 N. Cleveland-Massillon Rd. Akron, Ohio 44333-1255 Male D-Shell Connector Terminal Block 6 7 8 9 Pin Signal Wire 1 X Brown 2 SignalRed 3 Temp Orange 4 +5V Yellow 5 Y Green 6 7 Signal- SelfTest Blue Violet 8 +Vs Grey 9 Gnd White Ordering Information 23200A Bi-axial accelerometer 10 to 75 g (-Bnnn, -Rnnn, & -Tnnn options required) -Bnnn Bandwidth 3 dB cutoff (nnn Hz) -C001 Add accelerometer calibration certificate -C002 Add temperature calibration certificate -Rnnn Range (nnn g FSR) -Tnnn Terminal block (T000) or (nnn foot) cable with 9-pin male D-subminiature connector at end -W024 Extend warranty from 1 year to 2 years Voice: (330) 659-3312 Fax: (330) 659-3286 www.summitinstruments.com