2.5 VOLT HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40, 131,072 x 40 IDT72T4088, IDT72T4098 IDT72T40108, IDT72T40118 FEATURES * * * * * * * * * * * * * * Choose among the following memory organizations: IDT72T4088 16,384 x 40 IDT72T4098 32,768 x 40 IDT72T40108 65,536 x 40 IDT72T40118 131,072 x 40 Up to 250MHz operating frequency or 10Gbps throughput in SDR mode Up to 110MHz operating frequency or 10Gbps throughput in DDR mode Users selectable input port to output port data rates, 500Mb/s Data Rate -DDR to DDR -DDR to SDR -SDR to DDR -SDR to SDR User selectable HSTL or LVTTL I/Os Read Enable & Read Clock Echo outputs aid high speed operation 2.5V LVTTL or 1.8V, 1.5V HSTL Port Selectable Input/Ouput voltage 3.3V Input tolerant Mark & Retransmit, resets read pointer to user marked position Write Chip Select (WCS) input enables/disables Write Operations Read Chip Select (RCS) synchronous to RCLK Programmable Almost-Empty and Almost-Full flags, each flag * * * * * * * * * * * * can default to one of four preselected offsets Dedicated serial clock input for serial programming of flag offsets User selectable input and output port bus sizing -x40 in to x40 out -x40 in to x20 out -x40 in to x10 out -x20 in to x40 out -x10 in to x40 out Auto power down minimizes standby power consumption Master Reset clears entire FIFO Partial Reset clears data, but retains programmable settings Empty and Full flags signal FIFO status Select IDT Standard timing (using EF and FF flags) or First Word Fall Through timing (using OR and IR flags) Output enable puts data outputs into High-Impedance state JTAG port, provided for Boundary Scan function 208 Ball Grid array (PBGA), 17mm x 17mm, 1mm pitch Easily expandable in depth and width Independent Read and Write Clocks (permit reading and writing simultaneously) High-performance submicron CMOS technology Industrial temperature range (-40C to +85C) is available FUNCTIONAL BLOCK DIAGRAM D0 -Dn (x40, x20, x10) WEN WCS SREN SEN SCLK WCLK WSDR INPUT REGISTER WRITE CONTROL LOGIC MRS PRS TCK TRST TMS TDO RAM ARRAY 16,384 x 40, 32,768 x 40 65,536 x 40 131,072 x 40 FWFT FSEL0 FSEL1 READ POINTER BUS CONFIGURATION OUTPUT REGISTER RESET LOGIC Vref RT MARK RSDR READ CONTROL LOGIC JTAG CONTROL (BOUNDARY SCAN) RCLK REN RCS TDI HSTL FF/IR PAF EF/OR PAE FLAG LOGIC WRITE POINTER BM IW OW SI SO OFFSET REGISTER HSTL I/0 CONTROL EREN OE Q0 -Qn (x40, x20, x10) 5995 drw01 ERCLK IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. The TeraSync is a trademark of Integrated Device Technology, Inc. COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 2004 1 2004 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. DSC-5995/9 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES PIN CONFIGURATIONS A1 BALL PAD CORNER A V CC V CC D38 D1 D4 D7 D9 GND GND Q1 Q3 Q5 Q7 Q9 VDDQ VDDQ D35 D36 D39 D2 D5 D8 HSTL GND GND Q0 Q2 Q4 Q6 Q8 Q22 Q23 D34 D37 D0 D3 D6 V CC V CC GND GND VDDQ VDDQ VDDQ VDDQ Q20 Q21 Q24 D33 D32 D31 V CC V CC V CC V CC GND GND VDDQ VDDQ VDDQ VDDQ Q27 Q26 Q25 D30 TDI TRST GND VDDQ MARK Q29 Q28 TCK TMS TDO VDDQ VDDQ RCS RT REN WCLK FWFT PAF VDDQ GND GND GND GND GND VDDQ OE RCLK WEN WCS FF/IR VDDQ GND GND GND GND GND VDDQ SCLK SI MRS FSEL1 FSEL0 GND GND GND GND GND GND VDDQ SEN SREN IW BM PRS V CC GND GND GND GND GND VDDQ SO EREN WSDR RSDR OW V CC GND VDDQ PAE ERCLK D27 D28 D29 V CC VDDQ EF/OR Q30 Q31 D23 D20 D26 V CC V CC V CC V CC GND GND VDDQ VDDQ VDDQ VDDQ Q32 Q33 Q34 D24 D21 D18 GND V CC V CC V CC GND GND VDDQ VDDQ VDDQ VDDQ Q35 Q36 Q37 D25 D22 D19 D16 D14 D12 D10 GND GND Q19 Q17 Q15 Q13 Q11 Q38 Q39 V CC V CC VREF D17 D15 D13 D11 GND GND Q18 Q16 Q14 Q12 Q10 VDDQ VDDQ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 B C D E F G H J K L M N P R T 16 5995 drw02 PBGA: 1mm pitch, 17mm x 17mm (BB208-1, order code: BB) TOP VIEW 2 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES deasserted. Data will be read out of the FIFO on both rising and falling edge of RCLK when and REN is asserted. Both the input and output port can be selected for either 2.5V LVTTL or HSTL operation. This can be achieved by tying the HSTL signal LOW for LVTTL or HIGH for HSTL voltage operation. When the read port is setup for HSTL mode, the Read Chip Select (RCS) input also has the benefit of disabling the read port inputs, providing additional power savings. There is the option of selecting different data rates on the input and output ports of the device. There are a total of four combinations to choose from, Double Data Rate to Double Data Rate (DDR to DDR), DDR to Single Data Rate (DDR to SDR), SDR to DDR, and SDR to SDR. The rates can be set up using the WSDR and RSDR pins. For example, to set up the input to output combination of DDR to SDR, WSDR will be HIGH and RSDR will be LOW. Read and write operations are initiated on the rising edge of RCLK and WCLK respectively, never on the falling edge. If REN or WEN is asserted after a rising edge of clock, no read or write operations will be possible on the falling edge of that same pulse. An Output Enable (OE) input is provided for high-impedance control of the outputs. A read Chip Select (RCS) input is also provided for synchronous enable/disable of the read port control input, REN. The RCS input is synchronized to the read clock, and also provides high-impedance controls to the Qn data outputs. When RCS is disabled, REN will be disabled internally and the data outputs will be in High-Impedance. Unlike the Read Chip Select signal however, OE is not synchronous to RCLK. Outputs are high-impedanced shortly after a delay time when the OE transitions from LOW to HIGH. The Echo Read Enable (EREN) and Echo Read Clock (ERCLK) outputs are used to provide tighter synchronization between the data being transmitted from the Qn outputs and the data being received by the input device. These output signals from the read port are required for high-speed data communications. Data read from the read port is available on the output bus with respect to EREN and ERCLK, which is useful when data is being read at high-speed operations where synchronization is important. The frequencies of both the RCLK and WCLK signals may vary from 0 to fMAX with complete independence. There are no restrictions on the frequency of one clock input with respect to another. There are two possible timing modes of operation with these devices: IDT Standard mode and First Word Fall Through (FWFT) mode. In IDT Standard mode, the first word written to an empty FIFO will not appear on the data output lines unless a specific read operation is performed. A read operation, which consists of activating REN and enabling a rising RCLK edge, will shift the word from internal memory to the data output lines. Be aware that in Double Data Rate (DDR) mode only the IDT Standard mode is available. In FWFT mode, the first word written to an empty FIFO is clocked directly to the data output lines after three transitions of RCLK. A read operation does not have to be performed to access the first word written to the FIFO. However, subsequent words written to the FIFO do require a LOW on REN for access. The state of the FWFT input during Master Reset determines the timing mode in use. For applications requiring more data storage capacity than a single FIFO can provide, the FWFT timing mode permits depth expansion by chaining FIFOs in series (i.e. the data outputs of one FIFO are connected to the corresponding data inputs of the next). No external logic is required. These FIFOs have four flag pins, EF/OR (Empty Flag or Output Ready), FF/ IR (Full Flag or Input Ready), PAE (Programmable Almost-Empty flag), and PAF (Programmable Almost-Full flag). The EF and FF functions are selected in IDT Standard mode. The IR and OR functions are selected in FWFT mode. PAE and PAF are always available for use, irrespective of timing mode. DESCRIPTION The IDT72T4088/72T4098/72T40108/72T40118 are exceptionally deep, extremely high speed, CMOS First-In-First-Out (FIFO) memories with the ability to read and write data on both rising and falling edges of clock. The device has a flexible x40/x20/x10 Bus-Matching mode and the option to select single or double data rates for input and output ports. These FIFOs offer several key user benefits: * Flexible x40/x20/x10 Bus-Matching on both read and write ports * Ability to read and write on both rising and falling edges of a clock * User selectable Single or Double Data Rate of input and output ports * A user selectable MARK location for retransmit * User selectable I/O structure for HSTL or LVTTL * The first word data latency period, from the time the first word is written to an empty FIFO to the time it can be read, is fixed and short. * High density offerings up to 5Mbit * 10Gbps throughput Bus-Matching Double Data Rate FIFOs are particularly appropriate for network, video, telecommunications, data communications and other applications that require fast data transfer on both rising and falling edges of the clock. This is a great alternative to increasing data rate without extending the width of the bus or the speed of the device. They are also effective in applications that need to buffer large amounts of data and match buses of unequal sizes. Each FIFO has a data input port (Dn) and a data output port (Qn), both of which can assume either a 40-bit, 20-bit, or a 10-bit width as determined by the state of external control pins Input Width (IW), Output Width (OW), and BusMatching (BM) pin during the Master Reset cycle. The input port is controlled by a Write Clock (WCLK) input and a Write Enable (WEN) input. Data present on the Dn data inputs can be written into the FIFO on every rising and falling edge of WCLK when WEN is asserted and Write Single Data Rate (WSDR) pin held HIGH. Data can be selected to write only on the rising edges of WCLK if WSDR is asserted. To guarantee functionality of the device, WEN must be a controlled signal and not tied to ground. This is important because WEN must be HIGH during the time when the Master Reset (MRS) pulse is LOW. In addition, the WSDR pin must be tied HIGH or LOW. It is not a controlled signal and cannot be changed during FIFO operation. Write operations can be selected for either Single or Double Data Rate mode. For Single Data Rate operation, writing into the FIFO requires the Write Single Data Rate (WSDR) pin to be asserted. Data will be written into the FIFO on the rising edge of WCLK when the Write Enable (WEN) is asserted. For Double Data Rate operations, writing into the FIFO requires WSDR to be deasserted. Data will be written into the FIFO on both rising and falling edge of WCLK when WEN is asserted. The output port is controlled by a Read Clock (RCLK) input and a Read Enable (REN) input. Data is read from the FIFO on every rising and falling edge of RCLK when REN is asserted and Read Single Data Rate (RSDR) pin held HIGH. Data can be selected to read only on the rising edges of RCLK if RSDR is asserted. To guarantee functionality of the device, REN must be a controlled signal and not tied to ground. This is important because REN must be HIGH during the time when the Master Reset (MRS) pulse is LOW. In addition, the RSDR pin must be tied HIGH or LOW. It is not a controlled signal and cannot be changed during FIFO operation. Read operations can be selected for either Single or Double Data Rate mode. Similar to the write operations, reading from the FIFO in single data rate requires the Read Single Data Rate (RSDR) pin to be asserted. Data will be read from the FIFO on the rising edge of RCLK when the Read Enable (REN) is asserted. For Double Data Rate operations, reading into the FIFO requires RSDR to be 3 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES not WCLK. Similarly the PAF is asserted and updated on the rising edge of WCLK only and not RCLK. This device includes a Retransmit from Mark feature that utilizes two control inputs, MARK and RT (Retransmit). If the MARK input is enabled with respect to the RCLK, the memory location being read at the point will be marked. Any subsequent retransmit operation (when RT goes LOW), will reset the read pointer to this "marked" location. The device can be configured with different input and output bus widths as previously stated. These rates are: x40 to x40, x40 to x20,x40 to x10, x20 to x40, and x10 to x40. If, at any time, the FIFO is not actively performing an operation, the chip will automatically power down. Once in the power down state, the standby supply current consumption is minimized. Initiating any operation (by activating control inputs) will immediately take the device out of the power down state. A JTAG test port is provided, here the FIFO has fully functional boundary Scan feature, compliant with IEEE 1449.1 Standard Test Access Port and Boundary Scan Architecture. The Double Data Rate FIFO has the capability of operating in either LVTTL or HSTL mode. HSTL mode can be selected by enabling the HSTL pin. Both input and output ports will operate in either HSTL or LVTTL mode, but cannot be selected independent of one another. The IDT72T4088/72T4098/72T40108/72T40118 are fabricated using IDT's high-speed submicron CMOS technology. DESCRIPTION (CONTINUED) PAE and PAF flags can be programmed independently to switch at any point in memory. Programmable offsets mark the location within the internal memory that activates the PAE and PAF flags and can only be programmed serially. To program the offsets, set SEN active and data can be loaded via the Serial Input (SI) pin at the rising edge of SCLK. To read out the offset registers serially, set SREN active and data can be read out via the Serial Output (SO) pin at the rising edge of SCLK. Four default offset settings are also provided, so that PAE can be marked at a predefined number of locations from the empty boundary and the PAF threshold can also be marked at similar predefined values from the full boundary. The default offset values are set during Master Reset by the state of the FSEL0 and FSEL1 pins. During Master Reset (MRS), the following events occur: the read and write pointers are set to the first location of the internal FIFO memory, the FWFT pin selects IDT Standard mode or FWFT mode, the bus width configuration of the read and write port is determined by the state of IW and OW, and the default offset values for the programmable flags are set. The Partial Reset (PRS) also sets the read and write pointers to the first location of the memory. However, the timing mode and the values stored in the programmable offset registers before Partial Reset remain unchanged. The flags are updated according to the timing mode and offsets in effect. PRS is useful for resetting a device in mid-operation, when reprogramming programmable flags would be undesirable. The timing of the PAE and PAF flags are synchronous to RCLK and WCLK, respectively. The PAE flag is asserted upon the rising edge of RCLK only and 4 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 PARTIAL RESET (PRS) COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES MASTER RESET (MRS) WRITE CLOCK (WCLK) READ CLOCK (RCLK) WRITE ENABLE (WEN) READ ENABLE (REN) OUTPUT ENABLE (OE) WRITE CHIP SELECT (WCS) IDT 72T4088 72T4098 72T40108 72T40118 WRITE SINGLE DATA RATE (WSDR) (x40, x20, x10) DATA IN (D0 - Dn) READ CHIP SELECT (RCS) READ SINGLE DATA RATE (RSDR) (x40, x20, x10) DATA OUT (Q0 - Qn) RCLK ECHO (ERCLK) SERIAL CLOCK (SCLK) REN ECHO (EREN) SERIAL ENABLE(SEN) MARK SERIAL READ ENABLE(SREN) FIRST WORD FALL THROUGH (FWFT) SERIAL INPUT (SI) SERIAL OUTPUT (SO) FULL FLAG/INPUT READY (FF/IR) PROGRAMMABLE ALMOST-FULL (PAF) RETRANSMIT (RT) EMPTY FLAG/OUTPUT READY (EF/OR) PROGRAMMABLE ALMOST-EMPTY (PAE) 5995 drw03 OUTPUT WIDTH (OW) INPUT WIDTH (IW) Figure 1. Single Device Configuration Signal Flow Diagram TABLE 1 -- BUS-MATCHING CONFIGURATION MODES BM IW OW Write Port Width Read Port Width L L L x40 x40 H L L x40 x20 H L H x40 x10 H H L x20 x40 H H H x10 x40 NOTE: 1. Pin status during Master Reset. TABLE 2 -- DATA RATE-MATCHING CONFIGURATION MODES WSDR RSDR Write Port Width Read Port Width H H Double Data Rate Double Data Rate H L Double Data Rate Single Data Rate L H Single Data Rate Double Data Rate L L Single Data Rate Single Data Rate NOTE: 1. Pin status during Master Reset. 2. Data Rate Matching can be used in conjunction with Bus-Matching modes. 5 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES PIN DESCRIPTION Symbol & Pin No. BM(1) (K2) Name Bus-Matching I/O TYPE LVTTL INPUT Description During Master Reset, this pin along with IW and OW selects the bus sizes for both write and read ports. Data Inputs D0-D39 (See Pin No. table for details) HSTL-LVTTL Data inputs for a 40-, 20-, or 10-bit bus. When in 20- or 10- bit mode, the unused input pins are in a don't INPUT care state. The data bus is sampled on both rising and falling edges of WCLK when WEN is enabled and DDR Mode is enabled or on the rising edges of WCLK only in SDR Mode. EF/OR (M14) Empty Flag/ Output Ready HSTL-LVTTL In the IDT Standard mode, the EF function is selected. EF indicates whether or not the FIFO memory OUTPUT is empty. In FWFT mode, the OR function is selected. OR indicates whether or not there is valid data available at the outputs. ERCLK (L16) Echo Read Clock HSTL-LVTTL Read Clock Echo output, must be equal to or faster than the Qn data outputs. OUTPUT EREN (K16) Echo Read Enable HSTL-LVTTL Read Enable Echo output, used in conjunction with ERCLK. OUTPUT FF/IR (H3) Full Flag/ Input Ready HSTL-LVTTL In the IDT Standard mode, the FF function is selected. FF indicates whether or not the FIFO memory is OUTPUT empty. In FWFT mode, the IR function is selected. IR indicates whether or not there is space available for writing to the FIFO memory. FSEL0(1) (J3) Flag Select Bit 0 LVTTL INPUT During Master Reset, this input along with FSEL1 will select the default offset values for the programmable flags PAE and PAF. There are four possible settings available. FSEL1(1) (J2) Flag Select Bit 1 LVTTL INPUT During Master Reset, this input along with FSEL0 will select the default offset values for the programmable flags PAE and PAF. There are four possible settings available. FWFT (G2) First Word Fall Through LVTTL INPUT During Master reset, selects First Word Fall Through or IDT Standard mode. FWFT is not available in DDR mode. In SDR mode, the first word will always fall through on the rising edge. HSTL(1) (B7) HSTL Select LVTTL INPUT This input pin is used to select HSTL or 2.5V LVTTL device operation. If HSTL inputs are required, this input must be tied HIGH, otherwise it must be tied LOW and cannot toggle during operation. IW(1) (K1) Input Width LVTTL INPUT During Master Reset, this pin along with OW and BM, selects the bus width of the read and write port. MARK (E14) Mark Read Pointer for Retransmit HSTL-LVTTL When this pin is asserted the current location of the read pointer will be marked. Any subsequent Retransmit INPUT operation will reset the read pointer to this position. There is an unlimited number to times to set the mark location, but only the most recent location marked will be acknowledged. MRS (J1) Master Reset HSTL-LVTTL MRS initializes the read and write pointers to zero and sets the output registers to all zeros. During Master INPUT Reset, the FIFO is configured for either FWFT or IDT Standard mode, Bus-Matching configurations, and programmable flag default settings. OE (G15) Output Enable HSTL-LVTTL When HIGH, data outputs Q0-Q39 are in high impedance. When LOW, the data outputs Q0-Q39 are enabled. INPUT No other outputs are affected by OE. OW(1) (L3) Output Width PAE (L15) Programmable Almost-Empty Flag PAF (G3) Programmable HSTL-LVTTL PAF goes HIGH if the number of free locations in the FIFO memory is more than offset m, which is stored Almost-Full Flag OUTPUT in the Full Offset register. PAF goes LOW if the number of free locations in the FIFO memory is less than or equal to m. PRS (K3) Partial Reset HSTL-LVTTL PRS initializes the read and write pointers to zero and sets the output registers to all zeros. During Partial INPUT Reset, the existing mode (IDT standard or FWFT) and programmable flag settings are not affected. Q0-Q39 Data Outputs (See Pin No. table for details) HSTL-LVTTL Data outputs for a 40-, 20-, or 10-bit bus. When in 20- or 10- bit mode, the unused output pins should not OUTPUT be connected. The output data is clocked on both rising and falling edges of RCLK when REN is enabled and DDR Mode is enabled or on the rising edges of RCLK only in SDR Mode. RCLK (G16) HSTL-LVTTL Input clock when used in conjunction with REN for reading data from the FIFO memory and output register. INPUT Read Clock LVTTL INPUT During Master Reset, this pin along with IW and BM, selects the bus width of the read and write port. HSTL-LVTTL PAE goes HIGH if the number of words in the FIFO memory is greater than or equal to offset n, which is OUTPUT stored in the Empty Offset register. PAE goes LOW if the number of words in the FIFO memory is less than offset n. 6 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES PIN DESCRIPTION (CONTINUED) Symbol & Pin No. RCS (F14) Name I/O TYPE Description Read Chip Select HSTL-LVTTL RCS provides synchronous enable/disable control of the read port and High-Impedance control of the INPUT Qn data outputs, synchronous to RCLK. When using RCS the OE pin must be tied LOW. During Master or Partial Reset the RCS input is don't care, if OE is LOW the data outputs will be Low-Impedance regardless of RCS. REN (F16) Read Enable HSTL-LVTTL When LOW and in DDR mode, REN along with a rising and falling edge of RCLK will send data in FIFO INPUT memory to the output register and read the current data in output register. In SDR mode data will only be read on the rising edge of RCLK only. RSDR(1) (L2) Read Single Data Rate RT (F15) Retransmit SCLK (H15) Serial Clock SEN (J15) Serial Input Enable HSTL-LVTTL SEN used in conjunction with SI and SCLK enables serial loading of the programmable flag offsets. INPUT SREN (J16) Serial Read Enable HSTL-LVTTL SREN used in conjunction with SO and SCLK enables serial reading of the programmable flag offsets. INPUT SI (H16) Serial Input HSTL-LVTTL This input pin is used to load serial data into the programmable flag offsets. Used in conjunction with SEN INPUT and SCLK. SO (K15) Serial Output HSTL-LVTTL This output pin is used to read data from the programmable flag offsets. Used in conjunction with SREN OUTPUT and SCLK. TCK(2) (F1) JTAG Clock HSTL-LVTTL Clock input for JTAG function. One of four terminals required by IEEE Standard 1149.1-1990. Test INPUT operations of the device are synchronous to TCK. Data from TMS and TDI are sampled on the rising edge of TCK and outputs change on the falling edge of TCK. If the JTAG function is not used this signal needs to be tied to GND. TDI(2) (E2) JTAG Test Data Input HSTL-LVTTL One of four terminals required by IEEE Standard 1149.1-1990. During the JTAG boundary scan operation, INPUT test data serially loaded via the TDI on the rising edge of TCK to either the Instruction Register, ID Register and Bypass Register. An internal pull-up resistor forces TDI HIGH if left unconnected. TDO(2) (F3) JTAG Test Data Output HSTL-LVTTL One of four terminals required by IEEE Standard 1149.1-1990. During the JTAG boundary scan operation, OUTPUT test data serially loaded output via the TDO on the falling edge of TCK from either the Instruction Register, ID Register and Bypass Register. This output is high impedance except when shifting, while in SHIFTDR and SHIFT-IR controller states. TMS(2) (F2) JTAG Mode Select HSTL-LVTTL TMS is a serial input pin. One of four terminals required by IEEE Standard 1149.1-1990. TMS directs the INPUT the device through its TAP controller states. An internal pull-up resistor forces TMS HIGH if left unconnected. TRST(2) (E3) JTAG Reset HSTL-LVTTL TRST is an asynchronous reset pin for the JTAG controller. The JTAG TAP controller does not INPUT automatically reset upon power-up, thus it must be reset by either this signal or by setting TMS= HIGH for five TCK cycles. If the TAP controller is not properly reset then the FIFO outputs will always be in highimpedance. If the JTAG function is used but the user does not want to use TRST, then TRST can be tied with MRS to ensure proper FIFO operation. If the JTAG function is not used then this signal needs to be tied to GND. An internal pull-up resistor forces TRST HIGH if left unconnected. WCLK (G1) Write Clock HSTL-LVTTL Input clock when used in conjunction with WEN for writing data into the FIFO memory. INPUT WCS (H2) Write Chip Select HSTL-LVTTL The WCS pin can be regarded as a second WEN input, enabling/disabling write operations. INPUT WEN (H1) Write Enable LVTTL INPUT When LOW, this input pin sets the read port to Single Data Clock mode. When HIGH, the read port will operate in Double Data Clock mode. This pin must be tied either HIGH or LOW and cannot toggle during operation. HSTL-LVTTL RT asserted on the rising edge of RCLK initializes the read pointer to the first location in memory. EF flag INPUT is set to LOW (OR to HIGH in FWFT mode). The write pointer, offset registers, and flag settings are not affected. If a mark has been set via the MARK input pin, then the read pointer will initialize to the mark location when RT is asserted. LVTTL INPUT A rising edge of SCLK will clock the serial data present on the SI input into the offset registers provided that SEN is enabled. A rising edge of SCLK will also read data out of the offset registers provided that SREN is enabled. HSTL-LVTTL When LOW and in DDR mode, WEN along with a rising and falling edge of WCLK will write data into the INPUT FIFO memory. In SDR mode data will only be read on the rising edge of RCLK only. 7 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES PIN DESCRIPTION (CONTINUED) Symbol & Pin No. WSDR(1) (L1) Name I/O TYPE Description Write Single Data Rate LVTTL INPUT When LOW, this input pin sets the write port to Single Data Clock mode. When HIGH, the write port will operate in Double Data Clock mode. This pin must be tied either HIGH or LOW and cannot toggle during operation. VCC (See below) +2.5V Supply INPUT There are Vcc supply inputs and must be connected to the 2.5V supply rail. VDDQ (See below) O/P Rail Voltage INPUT This pin should be tied to the desired voltage rail for providing power to the output drivers. Nominally 1.5V or 1.8V for HSTL, 2.5V for LVTTL. GND (See below) Core Ground Pin INPUT These are Ground pins are for the core device and must be connected to the GND rail. Vref (T3) Reference Voltage INPUT This is a Voltage Reference input and must be connected to a voltage level determined in the Recommended DC Operating Conditions section. This provides the reference voltage when using HSTL class inputs. If HSTL class inputs are not being used, this pin must be connected to GND. NOTES: 1. Inputs should not change state after Master Reset. 2. These pins are for the JTAG port. Please refer to pages 25-28 and Figures 5-7. PIN NUMBER TABLE Symbol Name I/O TYPE Pin Number D0-39 Data Inputs HSTL-LVTTL D0-C3, D1-A4, D2-B4, D3-C4, D4-A5, D5-B5, D6-C5, D7-A6, D8-B6, D9-A7, D10-R7, D11-T7, INPUT D12-R6, D13-T6, D14-R5, D15-T5, D16-R4, D17-T4, D18-P3, D19-R3, D20-N2, D21-P2, D22-R2, D23-N1, D24-P1, D25-R1, D26-N3, D(27-29)-M(1-3), D30-E1, D(31-33)-D(3-1), D34-C1, D(35,36)-B(1,2), D37-C2, D38-A3, D39-B3 Q0-39 Data Outputs HSTL-LVTTL Q0-B10, Q1-A10, Q2-B11, Q3-A11, Q4-B12, Q5-A12, Q6-B13, Q7-A13, Q8-B14, Q9-A14, Q10-T14 OUTPUT Q11-R14, Q12-T13, Q13-R13, Q14-T12, Q15-R12, Q16-T11, Q17-R11, Q18-T10, Q19-R10, Q(20,21)-C(14,15), Q(22,23)-B(15,16), Q24-C16, Q(25-27)-D(16-14), Q(28,29)-E(16,15), Q(30,31)-M(15,16), Q(32-34)- N(14-16), Q(35-37)-P(14-16), Q(38,39)-R(15,16) VCC +2.5V Supply INPUT A(1,2), C(6,7), D(4-7), K4, L4, M4, N(4-7), P(5-7), T(1,2) VDDQ O/P Rail Voltage INPUT A(15,16), C(10-13), D(10-13), E13, F(4,13), G(4,14), H(4,14), J14, K14, L14, M13, N(10-13), P(10-13), T(15,16) GND Ground Pin INPUT A(8,9), B(8,9), C(8,9), D(8,9), E4, G(7-10,13), H(7-10,13), J(4,7-10,13), K(7-10,13), L13, N(8,9), P(4,8,9), R(8,9), T(8,9) 8 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 ABSOLUTE MAXIMUM RATINGS COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES CAPACITANCE (TA = +25C, f = 1.0MHz) Symbol VTERM Rating Terminal Voltage with respect to GND Commercial -0.5 to +3.6(2) Unit V TSTG Storage Temperature -55 to +125 C IOUT DC Output Current -50 to +50 mA NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Compliant with JEDEC JESD8-5. VCC terminal only. Symbol Parameter(1) Conditions Max. Unit CIN(2,3) Input Capacitance VIN = 0V 10(3) pF COUT(1,2) Output Capacitance VOUT = 0V 10 pF NOTES: 1. With output deselected, (OE VIH). 2. Characterized values, not currently tested. 3. CIN for Vref is 20pF. RECOMMENDED DC OPERATING CONDITIONS Symbol VCC VDDQ GND VIH Parameter Typ. Max. Unit 2.375 2.375 0 1.7 VREF+0.2 VREF+0.2 2.5 2.5 0 -- -- -- 2.625 2.625 0 3.45 -- -- V V V V V V LVTTL eHSTL HSTL -0.3 -- -- -- -- -- 0.7 VREF-0.2 VREF-0.2 V V V eHSTL HSTL 0.8 0.68 0.9 0.75 1.0 0.9 V V 0 -- 70 C -40 -- 85 C Supply Voltage Output Rail Voltage for I/Os Supply Voltage Input High Voltage LVTTL eHSTL HSTL Input Low Voltage VIL Min. Voltage Reference Input VREF (HSTL only) TA Operating Temperature Commercial TA Operating Temperature Industrial NOTE: 1. VREF is only required for HSTL or eHSTL inputs. VREF should be tied LOW for LVTTL operation. DC ELECTRICAL CHARACTERISTICS (Commercial: VCC = 2.5V 0.125V, TA = 0C to +70C;Industrial: VCC = 2.5V 0.125V, TA = -40C to +85C) Symbol Parameter Min. Max. Unit ILI Input Leakage Current -10 10 A ILO Output Leakage Current -10 10 A VDDQ -0.4 VDDQ -0.4 VDDQ -0.4 -- -- -- -- -- -- 0.4V 0.4V 0.4V V V V V V V VOH (5) Output Logic "1" Voltage, IOH = -8 mA @VDDQ = 2.5V 0.125V (LVTTL) IOH = -8 mA @VDDQ = 1.8V 0.1V (eHSTL) IOH = -8 mA @VDDQ = 1.5V 0.1V (HSTL) IOL = 8 mA @VDDQ = 2.5V 0.125V (LVTTL) IOL = 8 mA @VDDQ = 1.8V 0.1V (eHSTL) IOL = 8 mA @VDDQ = 1.5V 0.1V (HSTL) VOL Output Logic "0" Voltage, ICC1(1,2) Active VCC Current (VCC = 2.5V) I/O = LVTTL I/O = HSTL I/O = eHSTL -- -- -- 20 60 60 mA mA mA ICC2(1) Standby VCC Current (VCC = 2.5V) I/O = LVTTL I/O = HSTL I/O = eHSTL -- -- -- 10 50 50 mA mA mA NOTES: 1. Both WCLK and RCLK toggling at 20MHz. Data inputs toggling at 10MHz. WCS = HIGH, REN or RCS = HIGH. 2. Typical ICC1 calculation: for LVTTL I/O ICC1 (mA) = 0.6mA x fs, fs = WCLK frequency = RCLK frequency (in MHz) for HSTL or eHSTL I/O ICC1 (mA) = 38mA + (0.7mA x fs), fs = WCLK frequency = RCLK frequency (in MHz) 3. Typical IDDQ calculation: With Data Outputs in High-Impedance: IDDQ (mA) = 0.15mA x fs With Data Outputs in Low-Impedance: IDDQ (mA) = (CL x VDDQ x fs x 2N)/2000 fs = WCLK frequency = RCLK frequency (in MHz), VDDQ = 2.5V for LVTTL; 1.5V for HSTL; 1.8V for eHSTL, N = Number of outputs switching. tA = 25C, CL = capacitive load (pf) 4. Total Power consumed: PT = [(VCC x ICC) + (VDDQ x IDDQ)]. 5. Outputs are not 3.3V tolerant. 9 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES AC ELECTRICAL CHARACTERISTICS(1) (Commercial: VCC = 2.5V 5%, TA = 0C to +70C;Industrial: VCC = 2.5V 5%, TA = -40C to +85C) Symbol fS1 fS2 tA tASO tCLK1 tCLK2 tCLKH1 tCLKH2 tCLKL1 tCLKL2 tDS tDH tENS tENH tWCSS tWCSH fC tSCLK tSCKH tSCKL tSDS tSDH tSENS tSENH tRS tRSS tHRSS tRSR tRSF tOLZ tOE tOHZ tWFF tREF tPAFS tPAES tERCLK tCLKEN tRCSLZ tRCSHZ tSKEW1 tSKEW2 tSKEW3 Parameter Clock Cycle Frequency SDR Clock Cycle Frequency DDR Data Access Time Data Access Serial Output Time Clock Cycle Time SDR Clock Cycle Time DDR Clock High Time SDR Clock High Time DDR Clock Low Time SDR Clock Low Time DDR Data Setup Time Data Hold Time Enable Setup Time Enable Hold Time WCS setup time WCS hold time Clock Cycle Frequency (SCLK) Serial Clock Cycle Serial Clock High Serial Clock Low Serial Data In Setup Serial Data In Hold Serial Enable Setup Serial Enable Hold Reset Pulse Width(3) Reset Setup Time HSTL Reset Setup Time Reset Recovery Time Reset to Flag and Output Time Output Enable to Output in Low Z(4) Output Enable to Output Valid Output Enable to Output in High Z(4) Write Clock to FF or IR Read Clock to EF or OR Write Clock to Programmable Almost-Full Flag Read Clock to Programmable Almost-Empty Flag RCLK to Echo RCLK output RCLK to Echo REN output RCLK to Active from High-Z RCLK to High-Z(4) Skew time between RCLK and WCLK for EF/OR and FF/IR Skew time between RCLK & WCLK for EF/OR & FF/IR in DDR mode Skew time between RCLK and WCLK for PAE and PAF Commercial IDT72T4088L4 IDT72T4098L4 IDT72T40108L4 IDT72T40118L4 Min. Max. -- 250 -- 110 0.6 3.2 0.6 3.2 4 -- 9.1 -- 1.8 -- 4.0 -- 1.8 -- 4.0 -- 1.2 -- 0.5 -- 1.2 -- 0.5 -- 1.2 -- 0.5 -- -- 10 100 -- 45 -- 45 -- 15 -- 5 -- 5 -- 5 -- 30 -- 15 -- 4 -- 10 -- -- 10 0 -- -- 3.2 -- 3.2 -- 3.2 -- 3.2 -- 3.2 -- 3.2 -- 3.6 -- 3.2 -- 3.2 -- 3.2 3.5 -- 3.5 -- 4 -- Commercial IDT72T4088L5 IDT72T4098L5 IDT72T40108L5 IDT72T40118L5 Min. Max. -- 200 -- 100 0.6 3.6 0.6 3.6 5 -- 10 -- 2.3 -- 4.5 -- 2.3 -- 4.5 -- 1.5 -- 0.5 -- 1.5 -- 0.5 -- 1.5 -- 0.5 -- -- 10 100 -- 45 -- 45 -- 15 -- 5 -- 5 -- 5 -- 30 -- 15 -- 4 -- 10 -- -- 12 0 -- -- 3.6 -- 3.6 -- 3.6 -- 3.6 -- 3.6 -- 3.6 -- 4 -- 3.6 -- 3.6 -- 3.6 4 -- 4 -- 5 -- Com'l & Ind'l(2) Commercial IDT72T4088L6-7 IDT72T4088L10 IDT72T4098L6-7 IDT72T4098L10 IDT72T40108L6-7 IDT72T40108L10 IDT72T40118L6-7 IDT72T40118L10 Min. Max. Min. Max. Unit -- 150 -- 100 MHz -- 75 -- 50 MHz 0.6 3.8 0.6 4.5 ns 0.6 3.8 0.6 4.5 ns 6.7 -- 10 -- ns 13 -- 20 -- ns 2.8 -- 4.5 -- ns 6.0 -- 9.5 -- ns 2.8 -- 4.5 -- ns 6.0 -- 9.5 -- ns 2.0 -- 3.0 -- ns 0.5 -- 0.5 -- ns 2.0 -- 3.0 -- ns 0.5 -- 0.5 -- ns 2.0 -- 3.0 -- ns 0.5 -- 0.5 -- ns -- 10 -- 10 MHz 100 -- 100 -- ns 45 -- 45 -- ns 45 -- 45 -- ns 15 -- 15 -- ns 5 -- 5 -- ns 5 -- 5 -- ns 5 -- 5 -- ns 30 -- 30 -- ns 15 -- 15 -- ns 4 -- 4 -- s 10 -- 10 -- ns -- 15 -- 15 ns 0 -- 0 -- ns -- 3.8 -- 4.5 ns -- 3.8 -- 4.5 ns -- 3.8 -- 4.5 ns -- 3.8 -- 4.5 ns -- 3.8 -- 4.5 ns -- 3.8 -- 4.5 ns -- 4.3 -- 5 ns -- 3.8 -- 4.5 ns -- 3.8 -- 4.5 ns -- 3.8 -- 4.5 ns 5 -- 7 -- ns 5 -- 7 -- ns 6 -- 8 -- ns NOTES: 1. All AC timings apply to both IDT Standard mode and First Word Fall Through mode. 2. Industrial temperature range product for the 6-7ns speed grade is available as a standard device. All other speed grades are available by special order. 3. Pulse widths less than minimum values are not allowed. 4. Values guaranteed by design, not currently tested. 10 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES AC TEST LOADS HSTL 1.5V AC TEST CONDITIONS Input Pulse Levels Input Rise/Fall Times Input Timing Reference Levels Output Reference Levels VDDQ/2 0.25 to 1.25V 0.4ns 0.75V 0.75V 50 I/O Z0 = 50 10pF NOTE: 1. VDDQ = 1.5V. 5995 drw04 Figure 2a. AC Test Load EXTENDED HSTL 1.8V AC TEST CONDITIONS 5 0.4 to 1.4V 0.4ns 0.9V 0.9V tCD (Typical, ns) Input Pulse Levels Input Rise/Fall Times Input Timing Reference Levels Output Reference Levels 6 4 3 2 1 NOTE: 1. VDDQ = 1.8V. 20 30 50 80 100 Capacitance (pF) 200 5995 drw04a Figure 2b. Lumped Capacitive Load, Typical Derating 2.5V LVTTL 2.5V AC TEST CONDITIONS Input Pulse Levels Input Rise/Fall Times Input Timing Reference Levels Output Reference Levels GND to 2.5V 1ns 1.25V 1.25V NOTE: 1. For LVTTL VCC = VDDQ. 11 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES OUTPUT ENABLE & DISABLE TIMING Output Enable Output Disable VIH OE VIL tOE & tOLZ Output VCC Normally 2 LOW tOHZ VCC 2 100mV 100mV VOL VOH 100mV Output Normally VCC HIGH 2 100mV NOTES: 1. REN is HIGH. 2. RCS is LOW. VCC 2 5995 drw04b READ CHIP SELECT ENABLE & DISABLE TIMING VIH tENH RCS VIL tENS RCLK tRCSHZ tRCSLZ Output VCC Normally 2 LOW Output Normally VCC HIGH 2 VCC 2 100mV 100mV VOL VOH 100mV 100mV VCC 2 5995 drw04c NOTES: 1. REN is HIGH. 2. OE is LOW. 12 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES If the FIFO is full, the first read operation will cause FF to go HIGH. Subsequent read operations will cause PAF to go HIGH at the conditions described in Table 4 If further read operations occur, without write operations, PAE will go LOW when there are n words in the FIFO, where n is the empty offset value. Continuing read operations will cause the FIFO to become empty. Then the last word has been read from the FIFO, the EF will go LOW inhibiting further read operations. REN is ignored when the FIFO is empty. When configured in IDT Standard mode, the EF and FF outputs are double register-buffered outputs. IDT Standard mode is available when the device is configured in both Single Data Rate and Double Data Rate mode. Relevant timing diagrams for IDT Standard mode can be found in Figure 10, 11, 12, 13, 14, 15, 16, 17, 18 and 23. FUNCTIONAL DESCRIPTION TIMING MODES: IDT STANDARD vs FIRST WORD FALL THROUGH (FWFT) MODE The IDT72T4088/72T4098/72T40108/72T40118 support two different timing modes of operation: IDT Standard mode or First Word Fall Through (FWFT) mode. The selection of which mode will operate is determined during Master Reset, by the state of the FWFT input. During Master Reset, if the FWFT pin is LOW, then IDT Standard mode will be selected. This mode uses the Empty Flag (EF) to indicate whether or not there are any words present in the FIFO. It also uses the Full Flag function (FF) to indicate whether or not the FIFO has any free space for writing. In IDT Standard mode, every word read from the FIFO, including the first, must be requested using the Read Enable (REN) and RCLK. If the FWFT pin is HIGH during Master Reset, then FWFT mode will be selected. This mode uses Output Ready (OR) to indicate whether or not there is valid data at the data outputs (Qn). It also uses Input Ready (IR) to indicate whether or not the FIFO has any free space for writing. In the FWFT mode, the first word written to an empty FIFO goes directly to Qn after three RCLK rising edges, applying REN = LOW is not necessary. However, subsequent words must be accessed using the Read Enable (REN) and RCLK. Various signals, in both inputs and outputs operate differently depending on which timing mode is in effect. FIRST WORD FALL THROUGH MODE (FWFT) In this mode, the status flags OR, IR, PAE, and PAF operate in the manner outlined in Table 5. To write data into to the FIFO, WEN must be LOW. Data presented to the DATA IN lines will be clocked into the FIFO on subsequent transitions of WCLK. After the first write is performed, the Output Ready (OR) flag will go LOW. Subsequent writes will continue to fill up the FIFO. PAE will go HIGH after n + 2 words have been loaded into the FIFO, where n is the empty offset value. The default setting for these values are listed in Table 3. This parameter is also user programmable. See section on Programmable Flag Offset Loading. Continuing to write data into the FIFO without performing read operations will cause the Programmable Almost-Full flag (PAF) to go LOW. Again, if no reads are performed, the PAF will go LOW after (16,385-m) writes for the IDT72T4088, (32,769-m) writes for the IDT72T4098, (65,537-m) writes for the IDT72T40108 and (131,073-m) writes for the IDT72T40118. The offset "m" is the full offset value. The default setting for these values are listed in Table 3. This parameter is also user programmable. See the section on Programmable Flag Offset Loading. When the FIFO is full, the Input Ready (IR) will go LOW, inhibiting further write operations. If no reads are performed after a reset, IR will go LOW after D writes to the FIFO. D = 16,385 writes for the IDT72T4088, 32,769 writes for the IDT72T4098, 65,537 writes for the IDT72T40108 and 131,073 writes for the IDT72T40118, respectively. Note that the additional word in FWFT mode is due to the capacity of the memory plus output register. If the FIFO is full, the first read operation will cause IR to go HIGH. Subsequent read operations will cause PAF to go HIGH at the conditions described in Table 5. If further read operations occur, without write operations, PAE will go LOW when there are n words in the FIFO, where n is the empty offset value. Continuing read operations will cause the FIFO to become empty. Then the last word has been read from the FIFO, the OR will go HIGH inhibiting further read operations. REN is ignored when the FIFO is empty. When configured in FWFT mode, the OR flag output is triple register-buffered and the IR flag output is double register-buffered. FWFT mode is only available when the device is configured in Single Data Rate mode. Relevant timing diagrams for IDT Standard mode can be found in Figure 19, 20, 21, 22 and 24. IDT STANDARD MODE In this mode, the status flags FF, PAF, PAE, and EF operate in the manner outlined in Table 4. To write data into the FIFO, Write Enable (WEN) must be LOW. Data presented to the DATA IN lines will be clocked into the FIFO on subsequent transitions of the Write Clock (WCLK). After the first write is performed, the Empty Flag (EF) will go HIGH. Subsequent writes will continue to fill up the FIFO. The Programmable Almost-Empty flag (PAE) will go HIGH after n + 1 words have been loaded into the FIFO, where n is the empty offset value. The default setting for these values are listed in Table 3. This parameter is also user programmable. See section on Programmable Flag Offset Loading. Continuing to write data into the FIFO without performing read operations will cause the Programmable Almost-Full flag (PAF) to go LOW. Again, if no reads are performed, the PAF will go LOW after (16,384-m) writes for the IDT72T4088, (32,768-m) writes for the IDT72T4098, (65,536-m) writes for the IDT72T40108 and (131,072-m) writes for the IDT72T40118. The offset "m" is the full offset value. The default setting for these values are listed in Table 3. This parameter is also user programmable. See the section on Programmable Flag Offset Loading. When the FIFO is full, the Full Flag (FF) will go LOW, inhibiting further write operations. If no reads are performed after a reset, FF will go LOW after D writes to the FIFO. D = 16,384 writes for the IDT72T4088, 32,768 writes for the IDT72T4098, 65,536 writes for the IDT72T40108 and 131,072 writes for the IDT72T40118, respectively. 13 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 TABLE 3 -- DEFAULT PROGRAMMABLE FLAG OFFSETS IDT72T4088, 72T4098, 72T40108, 72T40118 FSEL1 H L H L FSEL0 H H L L Offsets n,m 255 127 63 7 NOTES: 1. n = empty offset for PAE. 2. m = full offset for PAF. PROGRAMMING FLAG OFFSETS Full and Empty Flag offset values are user programmable. The IDT72T4088/ 72T4098/72T40108/72T40118 have internal registers for these offsets. There are four selectable default offset values during Master Reset. These offset values are shown in Table 3. The offset values can also be programmed serially into the FIFO. To load offset values, set SEN LOW and the rising edge of SCLK will COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES load data from the SI input into the offset registers. SCLK runs at a nominal speed of 10MHz at the maximum. The programming sequence starts with one bit for each SCLK rising edge, starting with the Empty Offset LSB and ending with the Full Offset MSB. The total number of bits per device is listed in Figure 3, Programmable Flag Offset Programming Sequence. See Figure 25, Loading of Programmable Flag Registers, for the timing diagram for this mode. The PAE and PAF can show a valid status only after the complete set of bits (for all offset registers) has been entered. The registers can be reprogrammed as long as the complete set of new offset bits is entered. In addition to loading offset values into the FIFO, it is also possible to read the current offset values. Similar to loading offset values, set SREN LOW and the rising edge of SCLK will send data from the offset registers out to the SO output port. When initializing a read to the offset registers, data will be read starting from the first location in the register, regardless of where it was last read. Figure 3, Programmable Flag Offset Programming Sequence, summarizes the control pins and sequence for programming offset registers and reading and writing into the FIFO. The offset registers may be programmed (and reprogrammed) any time after Master Reset. Valid programming ranges are from 0 to D-1. TABLE 4 STATUS FLAGS FOR IDT STANDARD MODE Number of Words in FIFO IDT72T4088 IDT72T4098 IDT72T40108 IDT72T40118 FF 0 0 0 0 H H H H (131,072-m) to 131,071 65,536 131,072 IDT72T40118 1 to n (1) (8,193) to (16,384-(m+1)) (16,384-m) to 16,383 1 to n (1) (16,385) to (32,768-(m+1)) (32,768-m) to 32,767 16,384 1 to n (1) 1 to n (1) (32,769) to (65,536-(m+1)) (65,537) to (131,072-(m+1)) (65,536-m) to 65,535 32,768 PAF PAE EF L L H L H H H H H L H H L L H H NOTE: 1. See table 3 for values for n, m. TABLE 5 STATUS FLAGS FOR FWFT MODE Number of Words in FIFO IDT72T4088 IDT72T4098 IDT72T40108 0 0 0 1 to n+1 (1) (8,194) to (16,385-(m+1)) (16,385-m) to 16,384 1 to n+1 (1) (16,386) to (32,769-(m+1)) (32,769-m) to 32,768 16,385 1 to n+1 0 (1) 32,769 65,537 PAF PAE OR L H L L (131,073-m) to 131,072 131,073 1 to n+1 (1) (32,770) to (65,537-(m+1)) (65,538) to (131,073-(m+1)) (65,537-m) to 65,536 IR L H H L L H H L L L H L H L H L 5995 drw05 NOTE: 1. See table 3 for values for n, m. 2. FWFT mode available only in Single Data Rate mode. 14 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 WSDR RSDR WEN REN SEN SREN WCLK RCLK X X 1 1 0 1 X X X X 1 1 1 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES IDT72T4088 IDT72T4098 IDT72T40108 IDT72T40118 SCLK Serial write to registers: 0 X X In SDR Mode 28 bits for the IDT72T4088 30 bits for the IDT72T4098 32 bits for the IDT72T40108 34 bits for the IDT72T40118 1 bit for each rising SCLK edge Starting with Empty Offset (LSB) Ending with Full Offset (MSB) Serial write to registers: In DDR Mode 26 bits for the IDT72T4088 28 bits for the IDT72T4098 30 bits for the IDT72T40108 32 bits for the IDT 72T40118 1 bit for each rising SCLK edge Starting with Empty Offset (LSB) Ending with Full Offset (MSB) Serial read from registers: Serial read from registers: In SDR Mode 28 bits for the IDT72T4088 30 bits for the IDT72T4098 32 bits for the IDT72T40108 34 bits for the IDT72T40118 1 bit for each rising SCLK edge Starting with Empty Offset (LSB) Ending with Full Offset (MSB) In DDR Mode 26 bits for the IDT72T4088 28 bits for the IDT72T4098 30 bits for the IDT72T40108 32 bits for the IDT72T40118 1 bit for each rising SCLK edge Starting with Empty Offset (LSB) Ending with Full Offset (MSB) 1 1 0 1 X X X X Write Memory (DDR) 0 1 0 1 X X X X Write Memory (SDR) 1 1 1 0 X X X X Read Memory (DDR) 1 0 1 0 X X X X Read Memory (SDR) X X 1 1 X X X X No Operation X 5995 drw06 NOTES: 1. The programming sequence applies to both IDT Standard and FWFT modes. 2. When the input or output ports are in DDR mode, the depth is reduced by half but the overall density remains the same. For example, the IDT72T4088 in SDR mode is 16,384 x 40 = 655,360, in DDR mode the configuration becomes 8,192 x 80 = 655,360. In both cases, the total density are the same. Figure 3. Programmable Flag Offset Programming Sequence 15 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 RETRANSMIT FROM MARK OPERATION The Retransmit from Mark feature allows FIFO data to be read repeatedly starting at a user-selected position. The FIFO is first put into retransmit mode that will "mark" a beginning word and also set a pointer that will prevent ongoing FIFO write operations from over-writing retransmit data. The retransmit data can be read repeatedly any number of times from the "marked" position. The FIFO can be taken out of retransmit mode at any time to allow normal device operation. The "mark" position can be selected any number of times, each selection over-writing the previous mark location. In Double Data Rate, data is always marked in pairs. That is, the unit of data read on the rising and falling edge of WCLK. If the data marked was read on the falling edge of RCLK, then the marked data will be the unit of data read from the rising and falling edge of that particular RCLK edge. Refer to Figure 23, Retransmit from Mark in Double Data Rate Mode, for the timing diagram in this mode. Retransmit operation is available in both IDT standard and FWFT modes. During IDT standard mode the FIFO is put into retransmit mode by a Lowto-High transition on RCLK when the MARK input is HIGH and EF is HIGH. The rising RCLK edge marks the data present in the FIFO output register as the first retransmit data. Again, the data is marked in pairs. Thus if the data marked was read on the falling edge of RCLK, the first part of retransmit will read out the data read on the rising edge of RCLK, followed by the data on the falling edge (the marked data). The FIFO remains in retransmit mode until a rising edge on RCLK occurs while MARK is LOW. Once a marked location has been set, a retransmit can be initiated by a rising edge on RCLK while the Retransmit input (RT) is LOW. REN must be HIGH (reads disabled) before bringing RT LOW. The device indicates the start of retransmit setup by setting EF LOW, also preventing reads. When EF goes HIGH, retransmit setup is complete and read operations may begin starting with the first unit of data at the MARK location. Since IDT standard mode is selected, every word read including the first "marked" word following a retransmit setup requires a LOW on REN. Note, write operations may continue as normal during all retransmit functions, however write operations to the "marked" location will be prevented. See Figure COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES 23, Retransmit from Mark in Double Data Rate Mode, for the relevant timing diagram. During FWFT mode the FIFO is put into retransmit mode by a rising RCLK edge when the MARK input is HIGH and OR is LOW. The rising RCLK edge marks the data present in the FIFO output register as the first retransmit data. The data is marked in pairs. The FIFO remains in retransmit mode until a rising RCLK edge occurs while MARK is LOW. Once a marked location has been set, a retransmit can be initiated by a rising RCLK edge while the Retransmit input (RT) is LOW. REN must be HIGH (reads disabled) before bringing RT LOW. The device indicates the start of retransmit setup by setting OR HIGH, preventing read operations. When OR goes LOW, retransmit setup is complete and on the next rising RCLK edge (RT goes HIGH), the contents of the first retransmit location are loaded onto the output register. Since FWFT mode is selected, the first word appears on the outputs regardless of REN, a LOW on REN is not required for the first word. Reading all subsequent words requires a LOW on REN to enable the rising RCLK edge. See Figure 24, Retransmit from Mark (FWFT mode) for the relevant timing diagram. Before a retransmit can be performed, there must be at least 1280 bits (or 160 bytes) of data between the write pointer and mark location. That is, 40 bits x32 for the x40 mode, 20 bits x64 for the x20 mode, and 10 bits x128 for the x10 mode. Also, once the Mark is set, the write pointer will not increment past the marked location, preventing overwrites of retransmit data. HSTL/LVTTL I/O This device supports both LVTTL and HSTL logic levels on the input and output signals. If LVTTL is desired, a LOW on the HSTL pin will set the inputs and outputs to LVTTL mode. If HSTL is desired, a HIGH on the HSTL pin will set the inputs and outputs to HSTL mode. VREF is the input voltage reference used in HSTL mode. Typically a logic HIGH in HSTL would be Vref + 0.2V and a logic LOW would be VREF - 0.2V. Table 6 illustrates which pins are and are not associated with this feature. Note that all "Static Pins" must be tied to Vcc or GND. These pins are LVTTL only and are purely device configuration pins. TABLE 6 -- I/O CONFIGURATION HSTL SELECT STATIC PINS HIGH = HSTL LOW = LVTTL LVTTL ONLY Write Port Dn (I/P) WCLK (I/P) WEN (I/P) WCS (I/P) Read Port Qn (O/P) RCLK (I/P) REN (I/P) RCS (I/P) MARK (I/P) OE (I/P) RT (I/P) Signal Pins EF/OR (O/P) PAF (O/P) PAE (O/P) FF/IR (O/P) ERCLK (O/P) EREN (O/P) SCLK (I/P) SI (I/P) SO (O/P) MRS (I/P) PRS (I/P) TCK (I/P) TMS (I/P) 16 TRST (I/P) TDI (I/P) TDO (O/P) SEN (I/P) SREN (I/P) Static Pins IW (I/P) OW (I/P) BM ((I/P) HSTL (I/P) FSEL1 (I/P) FSEL0 (I/P) FWFT (I/P) WSDR (I/P) RSDR (I/P) SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES If FWFT mode has been selected, the OR flag will go HIGH on the rising edge of RCLK that retransmit was initiated. OR will return LOW on the next rising edge of RCLK, which signifies that retransmit setup is complete. Under FWFT mode, the contents in the marked memory location will be loaded onto the output register on the next rising edge of RCLK. To access all subsequent data, a read operation will be required. Subsequent retransmit operations may be performed, each time the read pointer returning to the "marked" location. See Figure 24, Retransmit from Mark (FWFT Mode) for the relevant timing diagram. SIGNAL DESCRIPTION INPUTS: DATA IN (D0 - Dn) (D0 - D39) are data inputs for the 40-bit wide data, (D0 - D19) are data inputs for the 20-bit wide data, or (D0 - D9) are data inputs for 10-bit wide data. CONTROLS: MASTER RESET (MRS) A Master Reset is accomplished whenever the MRS input is taken to a LOW state. This operation sets the internal read and write pointers to the first location of the RAM array. PAE will go LOW and PAF will go HIGH. If FWFT is LOW during Master Reset then IDT Standard mode along with EF and FF are selected. EF will go LOW and FF will go HIGH, If FWFT is HIGH, then the First Word Fall Through (FWFT) mode, along with IR and OR are selected. OR will go HIGH and IR will go LOW. All control settings such as OW, IW, BM, WSDR, RSDR, FSEL0 and FSEL1 are defined during the Master Reset cycle. During a Master Reset the output register is initialized to all zeros. A Master Reset is required after power up before a write operation can take place. MRS is asynchronous. See Figure 8, Master Reset Timing, for the relevant timing diagram. MARK The MARK input is used to select Retransmit mode of operation. On a rising edge of RCLK while MARK is HIGH will mark the memory location of the data currently present on the output register, in addition placing the device in retransmit mode. Note, there must be a minimum of 1280 bits (or 160 bytes) of data between the write pointer and mark location. That is, 40 bits x32 for the x40 mode, 20 bits x64 for the x20 mode, and 10 bits x128 for the x10 mode. Also, once the MARK is set, the write pointer will not increment past the "marked" location until the MARK is deasserted. This prevents "overwriting" of retransmit data. The MARK input must remain HIGH during the whole period of retransmit mode, a rising edge of RCLK while MARK is LOW will take the device out of retransmit mode and into normal mode. Any number of MARK locations can be set during FIFO operation, only the last marked location taking effect. Once a mark location has been set the write pointer cannot be incremented past this marked location. During retransmit mode write operations to the device may continue without hindrance. PARTIAL RESET (PRS) A Partial Reset is accomplished whenever the PRS input is taken to a LOW state. As in the case of the Master Reset, the internal read and write pointers are set to the first location of the RAM array. PAE goes LOW and PAF goes HIGH. Whichever mode was active at the time of Partial Reset will remain active after Partial Reset. If IDT Standard Mode is active, then FF will go HIGH and EF will go LOW. If the First Word Fall Through mode is active, then OR will go HIGH and IR will go LOW. Following Partial Reset, all values held in the offset registers remain unchanged. The output register is initialized to all zeroes. PRS is asynchronous. Partial Reset is useful for resetting the read and write pointers to zero without affecting the values of the programmable flag offsets and the timing mode of the FIFO. See Figure 9, Partial Reset Timing, for the relevant timing diagram. FIRST WORD FALL THROUGH (FWFT) During Master Reset, the state of the FWFT input determines whether the device will operate in IDT Standard mode or First Word Fall Through (FWFT) mode. If, at the time of Master Reset, FWFT is LOW, then IDT Standard mode will be selected. This mode uses the Empty Flag (EF) to indicate whether or not there are any words present in the FIFO memory. It also uses the Full Flag function (FF) to indicate whether or not the FIFO memory has any free space for writing. In IDT Standard mode, every word read from the FIFO, including the first, must be requested using the Read Enable (REN) and RCLK. If, at the time of Master Reset, FWFT is HIGH, then FWFT mode will be selected. This mode uses Output Ready (OR) to indicate whether or not there is valid data at the outputs (Qn) to be read. It also uses Input Ready (IR) to indicate whether or not the FIFO memory has any free space for writing. In the FWFT mode, the first word written to an empty FIFO goes directly to Qn after three RCLK rising edges, bringing REN LOW is not necessary. Subsequent words must be accessed using the Read Enable (REN) and RCLK. Note that FWFT mode can only be used when the device is configured to Single Data Rate (SDR) mode. RETRANSMIT (RT) The Retransmit (RT) input is used in conjunction with the MARK input. Together they provide a means by which data previously read out of the FIFO can be reread any number of times. When the retransmit operation is selected (i.e. after data has been marked), a rising edge on RCLK while RT is LOW will reset the read pointer back to the memory location set by the user via the MARK input. If IDT Standard mode has been selected, the EF flag will go LOW on the rising edge of RCLK that retransmit was initiated (i.e. rising edge of RCLK while RT is LOW). EF will go back to HIGH on the next rising edge of RCLK, which signifies that retransmit setup is complete. The next read operation will access data from the "marked" memory location. Subsequent retransmit operations may be performed, each time the read pointer returning to the "marked" location. See Figure 23, Retransmit from Mark in Double Data Rate Mode (IDT Standard Mode) for the relevant timing diagram. WRITE CLOCK (WCLK) A write cycle is initiated on the rising and/or falling edge of the WCLK input. If the Write Single Data Rate (WSDR) pin is selected, data will be written only on the rising edge of WCLK, provided that WEN and WCS are LOW. If the WSDR is not selected, data will be written on both the rising and falling edge of WCLK, provided that WEN and WCS are LOW. Data setup and hold times must be met with respect to the LOW-to-HIGH transition of the WCLK. It is permissible to stop the WCLK. Note that while WCLK is idle, the FF, IR, and PAF flags will not be updated. The write and read clocks can either be independent or coincident. 17 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 WRITE ENABLE (WEN) When the WEN input is LOW, data may be loaded into the FIFO RAM array on the rising edge of every WCLK cycle if the device is not full. Data is stored in the RAM array sequentially and independently of any ongoing read operation. When WEN is HIGH, no new data is written in the RAM array on each WCLK cycle. To prevent data overflow in the IDT Standard mode, FF will go LOW, inhibiting further write operations. Upon the completion of a valid read cycle, FF will go HIGH, allowing a write to occur. The FF is updated by two WCLK cycles + tSKEW after the RCLK cycle. To prevent data overflow in the FWFT mode, IR will go HIGH, inhibiting further write operations. Upon the completion of a valid read cycle, IR will go LOW, allowing a write to occur. The IR flag is updated by two WCLK cycles + tSKEW after the valid RCLK cycle. WEN is ignored when the FIFO is full in either IDT Standard mode or FWFT. WRITE SINGLE DATA RATE (WSDR) When the Write Single Data Rate pin is LOW, the write port will be set to Single Data Rate mode. In this mode, all write operations are based only on the rising edge of WCLK, provided that WEN and WCS are LOW. When WSDR is HIGH, the read port will be set to Double Data Rate mode. In this mode, all write operations are based on both the rising and falling edge of WCLK, provided that WEN and WCS are LOW, on the rising edge of WCLK. READ CLOCK (RCLK) A read cycle is initiated on the rising and/or falling edge of the RCLK input. If the Read Single Data Rate (RSDR) pin is selected, data will be read only on the rising edge of RCLK, provided that REN and RCS are LOW. If the RSDR is not selected, data will be read on both the rising and falling edge of WCLK, provided that REN and RCS are LOW, on the rising edge of RCLK. Setup and hold times must be met with respect to the LOW-to-HIGH transition of the RCLK. It is permissible to stop the RCLK. Note that while RCLK is idle, the EF/ OR and PAE flags will not be updated. Write and Read Clocks can be independent or coincident. READ ENABLE (REN) When Read Enable is LOW, data is loaded from the RAM array into the output register on the rising edge of every RCLK cycle if the device is not empty. When the REN input is HIGH, the output register holds the previous data and no new data is loaded into the output register. The data outputs Q0-Qn maintain the previous data value. In IDT Standard mode, every word accessed at Qn, including the first word written to an empty FIFO, must be requested using REN provided that the Read Chip Select (RCS) is LOW. When the last word has been read from the FIFO, the Empty Flag (EF) will go LOW, inhibiting further read operations. REN is ignored when the FIFO is empty. Once a write is performed, EF will go HIGH allowing a read to occur. Both RCS and REN must be active LOW for data to be read out on the rising edge of RCLK. In FWFT mode, the first word written to an empty FIFO automatically goes to the outputs Qn, on the third valid LOW-to-HIGH transition of RCLK + tSKEW after the first write. REN and RCS do not need to be asserted LOW for the First Word to fall through to the output register. All subsequent words require that a read operation to be executed using REN and RCS. The LOW-to-HIGH COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES transition of RCLK after the last word has been read from the FIFO will make Output Ready (OR) go HIGH with a true read (RCLK with REN and RCS LOW), inhibiting further read operations. REN is ignored when the FIFO is empty. READ SINGLE DATA RATE (RSDR) When the Read Single Data Rate pin is LOW, the read port will be set to Single Data Rate mode. In this mode, all read operations are based only on the rising edge of RCLK, provided that REN and RCS are LOW. When RSDR is HIGH, the read port will be set to Double Data Rate mode. In this mode, all read operations are based on both the rising and falling edge of RCLK, provided that REN and RCS are LOW, on the rising edge of RCLK. SERIAL CLOCK (SCLK) The serial clock is used to load and read data in the programmable offset registers. Data from the Serial Input (SI) can be loaded into the offset registers on the rising edge of SCLK provided that SEN is LOW. Data can be read from the offset registers via the Serial Output (SO) on the rising edge of SCLK provided that SREN is LOW. The serial clock can operate at a maximum frequency of 10MHz and its parameters are different than the FIFO system clock. SERIAL ENABLE (SEN) The SEN input is an enable used for serial programming of the programmable offset registers. It is used in conjunction with SI and SCLK when programming the offset registers. When SEN is LOW, data at the Serial In (SI) input can be loaded into the offset register, one bit for each LOW-to-HIGH transition of SCLK. When SEN is HIGH, the offset registers retain the previous settings and no offsets are loaded. SEN functions the same way in both IDT Standard and FWFT modes. SERIAL READ ENABLE (SREN) The SREN output is an enable used for reading the value of the programmable offset registers. It is used in conjunction with SI and SCLK when reading from the offset registers. When SREN is LOW, data can be read out of the offset register from the SO output, one bit for each LOW-to-HIGH transition of SCLK. When SREN is HIGH, the reading of the offset registers will stop. Whenever SREN is activated values in the offset registers are read starting from the first location in the offset registers and not from where the last offset value was read. SREN functions the same way in both IDT Standard and FWFT modes. SERIAL IN (SI) This pin acts as a serial input for loading PAE and PAF offsets into the programmable offset registers. It is used in conjunction with the Serial Clock (SCLK) and the Serial Enable (SEN). Data from this input can be loaded into the offset register, one bit for each LOW-to-HIGH transition of SCLK provided that SEN is LOW. SERIAL OUT (SO) This pin acts as a serial output for reading the values of the PAE and PAF offsets in the programmable offset registers. It is used in conjunction with the Serial Clock (SCLK) and the Serial Enable Output (SREN). Data from the offset register can be read out using this pin, one-bit for each LOW-to-HIGH transition of SCLK provided that SREN is LOW. 18 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 OUTPUT ENABLE (OE) When Output Enable is LOW, the parallel output buffers receive data from the output register. When OE is HIGH, the output data bus (Qn) goes into a high-impedance state. During Master or Partial Reset the OE is the only input that can place the output data bus into high-impedance. During reset the RCS input can be HIGH or LOW and has no effect on the output data bus. COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES OUTPUTS: DATA OUT (Q0-Q39) (Q0 - Q39) are data outputs for 40-bit wide data, (Q0 - Q19) are data outputs for 20-bit wide data, or (Q0 - Q9) are data outputs for 10-bit wide data. FULL FLAG (FF/IR) This is a dual-purpose pin. In IDT Standard mode, the Full Flag (FF) function is selected. When the FIFO is full, FF will go LOW, inhibiting further write operations. When FF is HIGH, the FIFO is not full. If no reads are performed after a reset (either MRS or PRS), FF will go LOW after D writes to the FIFO (D = 16,384 for the IDT72T4088, 32,768 for the IDT72T4098, 65,536 for the IDT72T40108, 131,072 for the IDT72T40118. See Figure 10, Write Cycle and Full Flag Timing (IDT Standard Mode), for the relevant timing information. In FWFT mode, the Input Ready (IR) function is selected. IR goes LOW when memory space is available for writing in data. When there is no longer any free space left, IR goes HIGH, inhibiting further write operations. If no reads are performed after a reset (either MRS or PRS), IR will go HIGH after D writes to the FIFO (D = 16,385 for the IDT72T4088, 32,769 for the IDT72T4098, 65,537 for the IDT72T40108, 131,073 for the IDT72T40118). See Figure 19, Write Timing (FWFT Mode), for the relevant timing information. The IR status not only measures the contents of the FIFO memory, but also counts the presence of a word in the output register. Thus, in FWFT mode, the total number of writes necessary to deassert IR is one greater than needed to assert FF in IDT Standard mode. FF/IR is synchronous and updated on the rising edge of WCLK. FF/IR are double register-buffered outputs. Note, when the device is in Retransmit mode, this flag is a comparison of the write pointer to the "marked" location. This differs from normal mode where this flag is a comparison of the write pointer to the read pointer. READ CHIP SELECT (RCS) The Read Chip Select input provides synchronous control of the Read output port. When RCS goes LOW, the next rising edge of RCLK causes the Qn outputs to go to the low-impedance state. When RCS goes HIGH, the next RCLK rising edge causes the Qn outputs to return to high-impedance. During a Master or Partial Reset the RCS input has no effect on the Qn output bus, OE is the only input that provides high-impedance control of the Qn outputs. If OE is LOW, the Qn data outputs will be low-impedance regardless of RCS until the first rising edge of RCLK after a reset is complete. Then if RCS is HIGH the data outputs will go to high-impedance. The RCS input does not effect the operation of the flags. For example, when the first word is written to an empty FIFO, the EF will still go from LOW to HIGH based on a rising edge of RCLK, regardless of the state of the RCS input. Also, when operating the FIFO in FWFT mode the first word written to an empty FIFO will still be clocked through to the output register based on RCLK, regardless of the state of RCS. For this reason the user should pay extra attention when a data word is written to an empty FIFO in FWFT mode. If RCS is HIGH when an empty FIFO is written into, the first word will fall through to the output register but will not be available on the Qn outputs because they are in high-impedance. The user must take RCS active LOW to access this first word, placing the output bus in low-impedance. REN must remain HIGH for at least one cycle after RCS has gone LOW. A rising edge of RCLK with RCS and REN LOW will read out the next word. Care must be taken so as not to lose the first word written to an empty FIFO when RCS is HIGH. Refer to Figure 22, RCS and REN Read Operation (FWFT Mode). The RCS pin must also be active (LOW) in order to perform a Retransmit. See Figure 18 for Read Cycle and Read Chip Select Timing (IDT Standard Mode). See Figure 21 for Read Cycle and Read Chip Select Timing (FWFT Mode). EMPTY FLAG (EF/OR) This is a dual-purpose pin. In the IDT Standard mode, the Empty Flag (EF) function is selected. When the FIFO is empty, EF will go LOW, inhibiting further read operations. When EF is HIGH, the FIFO is not empty. See Figure 12, Read Cycle, Empty Flag and First Word Latency Timing (IDT Standard Mode), for the relevant timing information. In FWFT mode, the Output Ready (OR) function is selected. OR goes LOW at the same time that the first word written to an empty FIFO appears valid on the outputs. OR stays LOW after the RCLK LOW to HIGH transition that shifts the last word from the FIFO memory to the outputs. OR goes HIGH only with a true read (RCLK with REN = LOW). The previous data stays at the outputs, indicating the last word was read. Further data reads are inhibited until OR goes LOW again. See Figure 20, Read Timing (FWFT Mode), for the relevant timing information. EF/OR is synchronous and updated on the rising edge of RCLK. In IDT Standard mode, EF is a double register-buffered output. In FWFT mode, OR is a triple register-buffered output. WRITE CHIP SELECT (WCS) The WCS disables all Write Port inputs (data only) if it is held HIGH. To perform normal operations on the write port, the WCS must be enabled. HSTL SELECT (HSTL) The inputs that were listed in Table 6 can be setup to be either HSTL or LVTTL. If HSTL is HIGH, then HSTL operation of those signals will be selected. If HSTL is LOW , then LVTTL will be selected. BUS-MATCHING (BM, IW, OW) The pins BM, IW, and OW are used to define the input and output bus widths. During Master Reset, the state of these pins is used to configure the device bus sizes. See Table 1 for control settings. All flags will operate on the word/byte size boundary as defined by the selection of bus width. See Table 7 for Bus-Matching Write to Read Ratio. PROGRAMMABLE ALMOST-FULL FLAG (PAF) The Programmable Almost-Full flag (PAF) will go LOW when the FIFO reaches the almost-full condition. In IDT Standard mode, if no reads are performed after reset (MRS), PAF will go LOW after (D - m) words are written to the FIFO. The PAF will go LOW after (16,384-m) writes for the IDT72T4088, (32,768-m) writes for the IDT72T4098, (65,536-m) writes for the IDT72T40108, (131,072-m) writes for the IDT72T40118. The offset "m" is the full offset value. The default setting for this value is listed in Table 3. FLAG SELECT BITS (FSEL0 and FSEL1) These pins will select the four default offset values for the PAE and PAF flags during Master Reset. The four possible settings are listed on Table 3. Note that the status of these inputs should not change after Master Reset. 19 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 In FWFT mode, the PAF will go LOW after (16,385-m) writes for the IDT72T4088, (32,769-m) writes for the IDT72T4098, (65,537-m) writes for the IDT72T40108, (131,073-m) writes for the IDT72T40118. where m is the full offset value. The default setting for this value is listed in Table 3. See Figure 29, Programmable Almost-Full Flag Timing (IDT Standard and FWFT Mode), for the relevant timing information. Note, when the device is in Retransmit mode, this flag is a comparison of the write pointer to the "marked" location. This differs from normal mode where this flag is a comparison of the write pointer to the read pointer. PROGRAMMABLE ALMOST-EMPTY FLAG (PAE) The Programmable Almost-Empty flag (PAE) will go LOW when the FIFO reaches the almost-empty condition. In IDT Standard mode, PAE will go LOW when there are n words or less in the FIFO. The offset "n" is the empty offset value. The default setting for this value is stated in the footnote of Table 3. In FWFT mode, the PAE will go LOW when there are n+1 words or less in the FIFO. The default setting for this value is stated in Table 3. See Figure 30, Programmable Almost-Empty Flag Timing (IDT Standard and FWFT Mode), for the relevant timing information. ECHO READ CLOCK (ERCLK) The Echo Read Clock output is provided in both HSTL and LVTTL mode, selectable via HSTL. The ERCLK is a free-running clock output, it will always follow the RCLK input regardless of REN and RCS. The ERCLK output follows the RCLK input with an associated delay. This delay provides the user with a more effective read clock source when reading COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES data from the Qn outputs. This is especially helpful at high speeds when variables within the device may cause changes in the data access times. These variations in access time maybe caused by ambient temperature, supply voltage, or device characteristics. The ERCLK output also compensates for any trace length delays between the Qn data outputs and receiving devices inputs. Any variations effecting the data access time will also have a corresponding effect on the ERCLK output produced by the FIFO device, therefore the ERCLK output level transitions should always be at the same position in time relative to the data outputs. Note, that ERCLK is guaranteed by design to be slower than the slowest Qn, data output. Refer to Figure 4, Echo Read Clock and Data Output Relationship, Figure 27, Echo Read Clock & Read Enable Operation in Double Data Rate Mode and Figure 28, Echo RCLK & Echo REN Operation for timing information. ECHO READ ENABLE (EREN) The Echo Read Enable output is provided in both HSTL and LVTTL mode, selectable via HSTL. The EREN output is provided to be used in conjunction with the ERCLK output and provides the reading device with a more effective scheme for reading data from the Qn output port at high speeds. The EREN output is controlled by internal logic that behaves as follows: The EREN output is active LOW for the RCLK cycle that a new word is read out of the FIFO. That is, a rising edge of RCLK will cause EREN to go active, LOW if both REN and RCS are active, LOW and the FIFO is NOT empty. RCLK tERCLK tERCLK ERCLK tA tD tA tD QSLOWEST(3) 5995 drw07 NOTES: 1. REN is LOW. 2. tERCLK > tA, guaranteed by design. 3. Qslowest is the data output with the slowest access time, tA. 4. Time, tD is greater than zero, guaranteed by design. 5. REN = RCS = OE = 0. Figure 4. Echo Read Clock and Data Output Relationship 20 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES TABLE 7 -- BUS-MATCHING WRITE TO READ RATIO ONE WRITE TO ONE READ (1:1) x40 DDR Input to x40 DDR Output WSDR H RSDR H Configuration BM L x40 SDR Input to x40 SDR Output IW L WSDR L OW L x40 SDR Input to x20 DDR Output RSDR H Configuration BM H Configuration BM L IW L OW L SDR Write Clock x40 Data In SDR Read Clock x40 Data Out Positive Edge 1 D[39:0] <= LW1 Positive Edge 1 Q[39:0] <= LW1 DDR Write Clock x40 Data In DDR Read Clock x40 Data Out Positive Edge 1 D[39:0] <= LW1 Positive Edge 1 Q[39:0] <= LW1 Negative Edge 1 D[39:0] <= LW2 Negative Edge 1 Q[39:0] <= LW2 WSDR L RSDR L x20 DDR Input to x40 SDR Output IW L SDR Write Clock x40 Data In Positive Edge 1 D[39:20] <= W1 D[19:0] <= W2 WSDR H OW L RSDR L Configuration BM H IW H DDR Write Clock x20 Data In Positive Edge 1 D[19:0] <= W1 Negative Edge 1 D[19:0] <= W2 DDR Read Clock x20 Data Out Positive Edge 1 Q[19:0] <= W1 Negative Edge 1 Q[19:0] <= W2 OW L SDR Read Clock x40 Data Out Positive Edge 1 Q[39:20] <= W1 Q[19:0] <= W2 ONE WRITE TO TWO READ (1:2) x40 DDR Input to x40 SDR Output WSDR H Configuration RSDR BM L L x40 SDR Input to x20 SDR Output IW L DDR Write Clock x40 Data In Positive Edge 1 D[39:0] <= LW1 Negative Edge 1 D[39:0] <= LW2 WSDR L OW L RSDR H Configuration BM H DDR Write Clock x40 Data In Positive Edge 1 D[39:20] <= LW1 D[19:0] <= LW2 Negative Edge 1 D[39:20] <= LW3 D[19:0] <= LW4 IW L IW L OW L SDR Write Clock x40 Data In SDR Read Clock x20 Data Out Positive Edge 1 D[39:20] <= LW1 Positive Edge 1 Q[19:0] <= LW1 D[19:0] <= LW2 Positive Edge 2 Q[19:0] <= LW2 SDR Read Clock x40 Data Out Positive Edge 1 Q[39:0] <= LW1 Positive Edge 2 Q[39:0] <= LW1 x40 DDR Input to x20 DDR Output WSDR H Configuration RSDR BM L H x40 SDR Input to x10 DDR Output WSDR L OW L DDR Read Clock Positive Edge 1 Negative Edge 1 Positive Edge 2 Negative Edge 2 x20 Data Out Q[19:0] <= LW1 Q[19:0] <= LW2 Q[19:0] <= LW3 Q[19:0] <= LW4 RSDR H Configuration BM H SDR Write Clock x40 Data In Positive Edge 1 D[39:30] <= B1 D[29:20] <= B2 D[19:10] <= B3 D[9:0] <= B4 21 IW L OW H DDR Read Clock Positive Edge 1 Negative Edge 1 Positive Edge 2 Negative Edge 2 x10 Data Out Q[9:0] <= B1 Q[9:0] <= B2 Q[9:0] <= B3 Q[9:0] <= B4 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES TABLE 7 -- BUS-MATCHING WRITE TO READ RATIO (CONTINUED) ONE WRITE TO FOUR READ (1:4) x40 DDR Input to x20 SDR Output WSDR H RSDR L Configuration BM H DDR Write Clock x40 Data In Positive Edge 1 D[39:20] <= LW1 D[19:0] <= LW2 Negative Edge 1 D[39:20] <= LW3 D[19:0] <= LW4 IW L x40 SDR Input to x10 SDR Output WSDR L OW L SDR Read Clock Positive Edge 1 Positive Edge 2 Positive Edge 3 Positive Edge 4 RSDR L Configuration BM H SDR Write Clock x40 Data In Positive Edge 1 D[39:30] <= B1 D[29:20] <= B2 D[19:10] <= B3 D[9:0] <= B4 x20 Data Out Q[19:0] <= LW1 Q[19:0] <= LW2 Q[19:0] <= LW3 Q[19:0] <= LW4 IW L OW H SDR Read Clock Positive Edge 1 Positive Edge 2 Positive Edge 3 Positive Edge 4 x10 Data Out Q[9:0] <= B1 Q[9:0] <= B2 Q[9:0] <= B3 Q[9:0] <= B4 x40 DDR Input to x10 DDR Output WSDR H RSDR H Configuration BM H DDR Write Clock x40 Data In Positive Edge 1 D[39:30] <= B1 D[29:20] <= B2 D[19:10] <= B3 D[9:0] <= B4 Negative Edge 1 D[39:30] <= B5 D[29:20] <= B6 D[19:10] <= B7 D[9:0] <= B8 IW L OW H SDR Read Clock Positive Edge 1 Negaitive Edge 1 Positive Edge 2 Negaitive Edge 2 Positive Edge 3 Negaitive Edge 3 Positive Edge 4 Negaitive Edge 4 x10 Data Out Q[9:0] <= B1 Q[9:0] <= B2 Q[9:0] <= B3 Q[9:0] <= B4 Q[9:0] <= B5 Q[9:0] <= B6 Q[9:0] <= B7 Q[9:0] <= B8 ONE WRITE TO EIGHT READ (1:8) x40 DDR Input to x10 SDR Output WSDR H Configuration RSDR BM L H DDR Write Clock x40 Data In Positive Edge 1 D[39:30] <= B1 D[29:20] <= B2 D[19:10] <= B3 D[9:0] <= B4 Negative Edge 1 D[39:30] <= B5 D[29:20] <= B6 D[19:10] <= B7 D[9:0] <= B8 IW L OW H SDR Read Clock Positive Edge 1 Positive Edge 2 Positive Edge 3 Positive Edge 4 Positive Edge 5 Positive Edge 6 Positive Edge 7 Positive Edge 8 x10 Data Out Q[9:0] <= B1 Q[9:0] <= B2 Q[9:0] <= B3 Q[9:0] <= B4 Q[9:0] <= B5 Q[9:0] <= B6 Q[9:0] <= B7 Q[9:0] <= B8 22 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES TABLE 7 -- BUS-MATCHING WRITE TO READ RATIO (CONTINUED) TWO WRITE TO ONE READ (2:1) x40 SDR Input to x40 DDR Output WSDR L RSDR H Configuration BM L IW L x20 DDR Input to x40 DDR Output WSDR H OW L RSDR H Configuration BM H IW H SDR Write Clock x40 Data In DDR Read Clock x40 Data Out Positive Edge 1 D[39:0] <= LW1 Positive Edge 1 Q[39:0] <= LW1 Positive Edge 2 D[39:0] <= LW2 Negative Edge 1 Q[39:0] <= LW2 DDR Write Clock Positive Edge 1 Negative Edge 1 Positive Edge 2 Negative Edge 2 x20 SDR Input to x40 SDR Output x10 DDR Input to x40 SDR Output WSDR L RSDR L Configuration BM H SDR Write Clock x20 Data In Positive Edge 1 D[19:0] <= W1 Positive Edge 2 D[19:0] <= W2 IW H WSDR H OW L x20 Data In DDR Read Clock D[19:0] <= W1 Positive Edge 1 D[19:0] <= W2 D[19:0] <= W3 Negative Edge 1 D[19:0] <= W4 Configuration RSDR BM L H DDR Write Clock Positive Edge 1 Negative Edge 1 Positive Edge 2 Negative Edge 2 SDR Read Clock x40 Data Out Positive Edge 1 Q[39:20] <= W1 Q[19:0] <= W2 OW L IW H x40 Data Out Q[39:20] <= W1 Q[19:0] <= W2 Q[39:20] <= W3 Q[19:0] <= W4 OW H x10 Data In SDR Read Clock D[9:0] <= B1 Positive Edge 1 D[9:0] <= B2 D[9:0] <= B3 D[9:0] <= B4 x40 Data Out Q[39:30] <= B1 Q[29:20] <= B2 Q[19:10] <= B3 Q[9:0] <= B4 FOUR WRITE TO ONE READ (4:1) x20 SDR Input to x40 DDR Output WSDR L Configuration RSDR BM H H SDR Write Clock Positive Edge 1 Positive Edge 2 Positive Edge 3 Positive Edge 4 IW H x10 DDR Input to x40 DDR Output WSDR H OW L x20 Data In DDR Read Clock D[19:0] <= W1 Positive Edge 1 D[19:0] <= W2 D[19:0] <= W3 Negative Edge 1 D[19:0] <= W4 x40 Data Out Q[39:20] <= W1 Q[19:0] <= W2 Q[39:20] <= W3 Q[19:0] <= W4 DDR Write Clock Positive Edge 1 Negative Edge 1 Positive Edge 2 Negative Edge 2 Positive Edge 3 Negative Edge 3 Positive Edge 4 Negative Edge 4 x10 SDR Input to x40 SDR Output WSDR L Configuration RSDR BM L H SDR Write Clock Positive Edge 1 Positive Edge 2 Positive Edge 3 Positive Edge 4 IW H Configuration RSDR BM H H IW H OW H x10 Data In DDR Read Clock D[9:0] <= B1 Positive Edge 1 D[9:0] <= B2 D[9:0] <= B3 D[9:0] <= B4 D[9:0] <= B5 Negative Edge 2 D[9:0] <= B6 D[9:0] <= B7 D[9:0] <= B8 x40 Data Out Q[39:30] <= B1 Q[29:20] <= B2 Q[19:10] <= B3 Q[9:0] <= B4 Q[39:30] <= B5 Q[29:20] <= B6 Q[19:10] <= B7 Q[9:0] <= B8 OW H x10 Data In SDR Read Clock D[9:0] <= B1 Positive Edge 1 D[9:0] <= B2 D[9:0] <= B3 D[9:0] <= B4 x40 Data Out Q[39:30] <= B1 Q[29:20] <= B2 Q[19:10] <= B3 Q[9:0] <= B4 23 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES TABLE 7 -- BUS-MATCHING WRITE TO READ RATIO (CONTINUED) EIGHT WRITE TO ONE READ (8:1) x10 SDR Input to x40 DDR Output WSDR L RSDR H SDR Write Clock Positive Edge 1 Positive Edge 2 Positive Edge 3 Positive Edge 4 Positive Edge 5 Positive Edge 6 Positive Edge 7 Positive Edge 8 Configuration BM H IW H OW H x10 Data In DDR Read Clock D[9:0] <= B1 Positive Edge D[9:0] <= B2 D[9:0] <= B3 D[9:0] <= B4 D[9:0] <= B5 Negative Edge D[9:0] <= B6 D[9:0] <= B7 D[9:0] <= B8 x40 Data Out Q[39:30] <= B1 Q[29:20] <= B2 Q[19:10] <= B3 Q[9:0] <= B4 Q[39:30] <= B5 Q[29:20] <= B6 Q[19:10] <= B7 Q[9:0] <= B8 TABLE 8 -- TSKEW MEASUREMENT Data Port Configuration DDR Input to DDR Output DDR Input to SDR Output Status Flags TSKEW Measurement EF & PAE Negative Edge WCLK to Positive Edge RCLK FF & PAF Negative Edge RCLK to Positive Edge WCLK Negative Edge WCLK to Positive Edge RCLK EF & PAE FF & PAF SDR Input to DDR Output EF & PAE FF & PAF SDR Input to SDR Output EF & PAE FF & PAF Positive Edge RCLK to Positive Edge WCLK Positive Edge WCLK to Positive Edge RCLK Negative Edge RCLK to Positive Edge WCLK Positive Edge WCLK to Positive Edge RCLK Positive Edge RCLK to Positive Edge WCLK 24 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES JTAG TIMING SPECIFICATION tTCK t4 t1 t2 TCK t3 TDI/ TMS tDS tDH TDO TDO tDO t6 TRST 5995 drw08 Notes to diagram: t1 = tTCKLOW t2 = tTCKHIGH t3 = tTCKFALL t4 = tTCKRISE t5 = tRST (reset pulse width) t6 = tRSR (reset recovery) t5 Figure 5. Standard JTAG Timing JTAG AC ELECTRICAL CHARACTERISTICS (vcc = 2.5V 5%; Tcase = 0C to +85C) Parameter Symbol SYSTEM INTERFACE PARAMETERS Min. IDT72T4088 IDT72T4098 IDT72T40108 IDT72T40118 Test Conditions Parameter Symbol Data Output tDO(1) - 20 ns Data Output Hold tDOH(1) 0 - ns Data Input tDS tDH 10 10 - ns trise=3ns tfall=3ns Min. Test Conditions Max. Units NOTE: 1. 50pf loading on external output signals. Max. Units JTAG Clock Input Period tTCK - 100 - ns JTAG Clock HIGH tTCKHIGH - 40 - ns JTAG Clock Low tTCKLOW - 40 - ns JTAG Clock Rise Time tTCKRISE - - 5(1) ns JTAG Clock Fall Time tTCKFALL - - 5(1) ns JTAG Reset tRST - 50 - ns JTAG Reset Recovery tRSR - 50 - ns NOTE: 1. Guaranteed by design. 25 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES The Standard JTAG interface consists of four basic elements: Test Access Port (TAP) TAP controller Instruction Register (IR) Data Register Port (DR) JTAG INTERFACE * * * * Five additional pins (TDI, TDO, TMS, TCK and TRST) are provided to support the JTAG boundary scan interface. The IDT72T4088/72T4098/ 72T40108/72T40118 incorporates the necessary tap controller and modified pad cells to implement the JTAG facility. Note that IDT provides appropriate Boundary Scan Description Language program files for these devices. The following sections provide a brief description of each element. For a complete description refer to the IEEE Standard Test Access Port Specification (IEEE Std. 1149.1-1990). The Figure below shows the standard Boundary-Scan Architecture DeviceID Reg. Mux Boundary Scan Reg. Bypass Reg. TDO TDI T A TMS TCLK TRST P TAP Controller clkDR, ShiftDR UpdateDR Instruction Decode clklR, ShiftlR UpdatelR Instruction Register Control Signals 5995 drw09 Figure 6. Boundary Scan Architecture THE TAP CONTROLLER The Tap controller is a synchronous finite state machine that responds to TMS and TCLK signals to generate clock and control signals to the Instruction and Data Registers for capture and update of data. TEST ACCESS PORT (TAP) The Tap interface is a general-purpose port that provides access to the internal of the processor. It consists of four input ports (TCLK, TMS, TDI, TRST) and one output port (TDO). 26 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 1 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES Test-Logic Reset 0 0 Run-Test/ Idle 1 SelectDR-Scan 1 SelectIR-Scan 1 0 1 0 Capture-IR 1 Capture-DR 0 0 0 Shift-DR 1 Input = TMS EXit1-DR 1 1 0 1 Exit2-IR 0 1 1 Update-DR 0 0 Pause-IR 1 Exit2-DR 1 1 Exit1-IR 0 0 Pause-DR 0 0 Shift-IR Update-IR 1 0 5995 drw10 NOTES: 1. Five consecutive TCK cycles with TMS = 1 will reset the TAP. 2. TAP controller does not automatically reset upon power-up. The user must provide a reset to the TAP controller (either by TRST or TMS). 3. TAP controller must be reset before normal FIFO operations can begin. Figure 7. TAP Controller State Diagram Capture-IR In this controller state, the shift register bank in the Instruction Register parallel loads a pattern of fixed values on the rising edge of TCK. The last two significant bits are always required to be "01". Shift-IR In this controller state, the instruction register gets connected between TDI and TDO, and the captured pattern gets shifted on each rising edge of TCK. The instruction available on the TDI pin is also shifted in to the instruction register. Exit1-IR This is a controller state where a decision to enter either the PauseIR state or Update-IR state is made. Pause-IR This state is provided in order to allow the shifting of instruction register to be temporarily halted. Exit2-DR This is a controller state where a decision to enter either the ShiftIR state or Update-IR state is made. Update-IR In this controller state, the instruction in the instruction register is latched in to the latch bank of the Instruction Register on every falling edge of TCK. This instruction also becomes the current instruction once it is latched. Capture-DR In this controller state, the data is parallel loaded in to the data registers selected by the current instruction on the rising edge of TCK. Shift-DR, Exit1-DR, Pause-DR, Exit2-DR and Update-DR These controller states are similar to the Shift-IR, Exit1-IR, Pause-IR, Exit2-IR and Update-IR states in the Instruction path. Refer to the IEEE Standard Test Access Port Specification (IEEE Std. 1149.1) for the full state diagram All state transitions within the TAP controller occur at the rising edge of the TCLK pulse. The TMS signal level (0 or 1) determines the state progression that occurs on each TCLK rising edge. The TAP controller takes precedence over the FIFO memory and must be reset after power up of the device. See TRST description for more details on TAP controller reset. Test-Logic-Reset All test logic is disabled in this controller state enabling the normal operation of the IC. The TAP controller state machine is designed in such a way that, no matter what the initial state of the controller is, the Test-Logic-Reset state can be entered by holding TMS at high and pulsing TCK five times. This is the reason why the Test Reset (TRST) pin is optional. Run-Test-Idle In this controller state, the test logic in the IC is active only if certain instructions are present. For example, if an instruction activates the self test, then it will be executed when the controller enters this state. The test logic in the IC is idles otherwise. Select-DR-Scan This is a controller state where the decision to enter the Data Path or the Select-IR-Scan state is made. Select-IR-Scan This is a controller state where the decision to enter the Instruction Path is made. The Controller can return to the Test-Logic-Reset state other wise. 27 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 THE INSTRUCTION REGISTER The Instruction register allows an instruction to be shifted in serially into the processor at the rising edge of TCLK. The Instruction is used to select the test to be performed, or the test data register to be accessed, or both. The instruction shifted into the register is latched at the completion of the shifting process when the TAP controller is at UpdateIR state. The instruction register must contain 4 bit instruction register-based cells which can hold instruction data. These mandatory cells are located nearest the serial outputs they are the least significant bits. TEST DATA REGISTER The Test Data register contains three test data registers: the Bypass, the Boundary Scan register and Device ID register. These registers are connected in parallel between a common serial input and a common serial data output. The following sections provide a brief description of each element. For a complete description, refer to the IEEE Standard Test Access Port Specification (IEEE Std. 1149.1-1990). TEST BYPASS REGISTER The register is used to allow test data to flow through the device from TDI to TDO. It contains a single stage shift register for a minimum length in serial path. When the bypass register is selected by an instruction, the shift register stage is set to a logic zero on the rising edge of TCLK when the TAP controller is in the Capture-DR state. The operation of the bypass register should not have any effect on the operation of the device in response to the BYPASS instruction. THE BOUNDARY-SCAN REGISTER The Boundary Scan Register allows serial data TDI be loaded in to or read out of the processor input/output ports. The Boundary Scan Register is a part of the IEEE 1149.1-1990 Standard JTAG Implementation. THE DEVICE IDENTIFICATION REGISTER The Device Identification Register is a Read Only 32-bit register used to specify the manufacturer, part number and version of the processor to be determined through the TAP in response to the IDCODE instruction. IDT JEDEC ID number is 0xB3. This translates to 0x33 when the parity is dropped in the 11-bit Manufacturer ID field. For the IDT72T4088/72T4098/72T40108/72T40118, the Part Number field contains the following values: Device IDT72T4088 IDT72T4098 IDT72T40108 IDT72T40118 Part# Field 04A3 04A2 04A1 04A0 31(MSB) 28 27 12 11 1 0(LSB) Version (4 bits) Part Number (16-bit) Manufacturer ID (11-bit) 0X0 0X33 1 IDT72T4088/4098/40108/40118 JTAG Device Identification Register COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES JTAG INSTRUCTION REGISTER The Instruction register allows instruction to be serially input into the device when the TAP controller is in the Shift-IR state. The instruction is decoded to perform the following: * Select test data registers that may operate while the instruction is current. The other test data registers should not interfere with chip operation and the selected data register. * Define the serial test data register path that is used to shift data between TDI and TDO during data register scanning. The Instruction Register is a 4 bit field (i.e.IR3, IR2, IR1, IR0) to decode 16 different possible instructions. Instructions are decoded as follows. Hex Value 0x02 0x01 0x03 0x0F Instruction Function IDCODE SAMPLE/PRELOAD HI-IMPEDANCE BYPASS Select Chip Identification data register Select Boundary Scan Register JTAG Select Bypass Register Table 8. JTAG Instruction Register Decoding The following sections provide a brief description of each instruction. For a complete description refer to the IEEE Standard Test Access Port Specification (IEEE Std. 1149.1-1990). IDCODE The optional IDCODE instruction allows the IC to remain in its functional mode and selects the optional device identification register to be connected between TDI and TDO. The device identification register is a 32-bit shift register containing information regarding the IC manufacturer, device type, and version code. Accessing the device identification register does not interfere with the operation of the IC. Also, access to the device identification register should be immediately available, via a TAP data-scan operation, after power-up of the IC or after the TAP has been reset using the optional TRST pin or by otherwise moving to the Test-Logic-Reset state. SAMPLE/PRELOAD The required SAMPLE/PRELOAD instruction allows the IC to remain in a normal functional mode and selects the boundary-scan register to be connected between TDI and TDO. During this instruction, the boundary-scan register can be accessed via a date scan operation, to take a sample of the functional data entering and leaving the IC. HIGH-IMPEDANCE The optional High-Impedance instruction sets all outputs (including two-state as well as three-state types) of an IC to a disabled (high-impedance) state and selects the one-bit bypass register to be connected between TDI and TDO. During this instruction, data can be shifted through the bypass register from TDI to TDO without affecting the condition of the IC outputs. BYPASS The required BYPASS instruction allows the IC to remain in a normal functional mode and selects the one-bit bypass register to be connected between TDI and TDO. The BYPASS instruction allows serial data to be transferred through the IC from TDI to TDO without affecting the operation of the IC. EXTEST The required EXTEST instruction is not available for this device. 28 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES tRS MRS tRSS tRSR tRSS tRSR tRSS tRSR REN WEN FWFT(2) tRSS FSEL0(2), FSEL1 tRSS OW(2), IW, BM tHRSS HSTL(2) tRSS tRSR tRSS tRSR WSDR (2) RSDR(2) tRSS RT tRSS SEN tRSS SREN tRSF If FWFT = HIGH, OR = HIGH EF/OR If FWFT = LOW, EF = LOW tRSF If FWFT = LOW, FF = HIGH FF/IR If FWFT = HIGH, IR = LOW tRSF PAE tRSF PAF tRSF OE = HIGH Q0 - Qn OE = LOW 5995 drw11 NOTES: 1. During Master Reset the High-Impedance control of the Qn data outputs is provided by OE only, RCS can be HIGH or LOW until the first rising edge of RCLK after Master Reset is complete. 2. The status of these pins are latched in when the Master Reset pulse is LOW. Figure 8. Master Reset Timing 29 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES tRS PRS tRSS tRSR REN tRSS tRSR WEN tRSS RT tRSS SEN tRSS SREN If FWFT = HIGH, OR = HIGH tRSF EF/OR If FWFT = LOW, EF = LOW If FWFT = LOW, FF = HIGH tRSF FF/IR If FWFT = HIGH, IR = LOW tRSF PAE tRSF PAF tRSF OE = HIGH Q0 - Qn OE = LOW 5995 drw12 NOTE: 1. During Partial Reset the High-Impedance control of the Qn data outputs is provided by OE only, RCS can be HIGH or LOW until the first rising edge of RCLK after Master Reset is complete. Figure 9. Partial Reset Timing 30 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 WCLK 1 (1) tCLK1 tCLKL1 tCLKH1 NO WRITE COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES 2 tSKEW1 tDS NO WRITE 1 (1) tSKEW1 tDH 2 DX+1 DX D0 - D39 tWFF tDH tDS tWFF tWFF tWFF FF WEN RCLK tENS tENS tENH tENH REN tENS RCS tA tA Q0 - Q39 DATA READ NEXT DATA READ 5995 drw13 tRCSLZ NOTES: 1. tSKEW1 is the minimum time between a rising RCLK edge and a rising WCLK edge to guarantee that FF will go HIGH (after one WCLK cycle plus tWFF). If the time between the rising edge of the RCLK and the rising edge of the WCLK is less than tSKEW1, then the FF deassertion may be delayed one extra WCLK cycle. 2. OE = LOW, EF = HIGH. 3. WCS = LOW. 4. WCLK must be free running for FF to update. Figure 10. Write Cycle and Full Flag Timing (IDT Standard Mode) 31 SEPTEMBER 21, 2004 Data in Output Register tENS tA tENH tA Data Read tSKEW2(1) 1 2 Next Data Read tWFF tDS Dx tCLKL2 Dx+1 tDH tCLK2 tDS tWFF tDH tCLKH2 tENS tA tENH tA Next Data tSKEW2(1) 1 NO WRITE 2 Next Data Read tWFF Dx+2 tWFF Dx+3 5995 drw14 32 Figure 11. Write Cycle and Full Flag Timing in Double Data Rate Mode (IDT Standard Mode) NOTES: 1. tSKEW2 is the minimum time between a falling RCLK edge and a rising WCLK edge to guarantee that FF will go HIGH (after one WCLK cycle plus tWFF). If the time between the falling edge of the RCLK and the rising edge of WCLK is less than tSKEW2, then FF deassertion may be delayed one extra WCLK cycle. 2. OE = LOW, EF = HIGH. 3. WCS = LOW, RCS = LOW, WSDR = HIGH and RSDR = HIGH. 4. WCLK must be free running for FF to update. Q0-Q39 REN RCLK WEN FF D0-D39 WCLK NO WRITE IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES tCLKH1 1 RCLK tENS tCLK1 tCLKL1 2 tENH tENS REN tENH tENH tENS NO OPERATION NO OPERATION tREF tREF tREF EF tA tA LAST WORD Q0 - Q39 tOLZ tOHZ tOE tA D0 LAST WORD D1 tOLZ OE (1) tSKEW1 WCLK tENH tENS tENS tENH WEN tWCSS tWCS H WCS tDS D0 - D39 D0 tDH tDS tDH D1 5995 drw15 NOTES: 1. tSKEW1 is the minimum time between a rising WCLK edge and a rising RCLK edge to guarantee that EF will go HIGH (after one RCLK cycle plus tREF). If the time between the rising edge of WCLK and the rising edge of RCLK is less than tSKEW1, then EF deassertion may be delayed one extra RCLK cycle. 2. First data word latency = tSKEW1 + 1*TRCLK + tREF. 3. RCS is LOW. 4. RCLK must be free running for EF to update. Figure 12. Read Cycle, Output Enable, Empty Flag and First Data Word Latency (IDT Standard Mode) 33 SEPTEMBER 21, 2004 34 tOLZ tOE tA tREF Dn-1 tA tDS tWCSS tENS D0 tDH tWCSH tDS tENH Dn D1 tDH NO Read tSKEW2 (1) tOHZ 1 NO Read tOLZ 2 tREF tCLKH2 Dn tCLKL2 tCLK2 tA tREF D0 tA NO Read D1 5995 drw16 Figure 13. Read Cycle, Output Enable, Empty Flag and First Data Word Latency in Double Data Rate Mode (IDT Standard Mode) NOTES: 1. tSKEW2 is the minimum time between a falling WCLK edge and a rising RCLK edge to guarantee that EF will go HIGH (after one RCLK cycle plus tREF). If the time between the falling edge of WCLK and the rising edge of RCLK is less than tSKEW2, then EF deassertion may be delayed one extra RCLK cycle. 2. REN = LOW. 3. First data word latency = tSKEW1 + 1*tRCLK + tREF. 4. RCS = LOW, WSDR = HIGH and RSDR = HIGH. 5. RCLK must be free running for EF to update. D0-D39 WCS WEN WCLK OE Q0-Q39 EF RCLK NO Read IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 tDS tWCSS tENS W0 - W3 tDH 1 W4 - W7 tDS twcSH tENH tDH Previous Data in Ouput Register tSKEW2(1) tREF 2 tENS tA W0 tA W1 tA W2 tA W3 tA W4 tA W5 tA W6 tA tREF tENH 5995 drw17 W7 35 Figure 14. Read Cycle, Empty Flag and First Data Word Latency in x40DDR to x10SDR with Bus-Matching and Rate-Matching (IDT Standard Mode) NOTES: 1. tSKEW2 is the minimum time between a falling WCLK edge and a rising RCLK edge to guarantee that EF will go HIGH (after one RCLK cycle plus tREF). If the time between the falling edge of WCLK and the rising edge of RCLK is less than tSKEW2, then EF deassertion may be delayed one extra RCLK cycle. 2. REN = LOW. 3. First data word latency = tSKEW1 + 1*tRCLK + tREF. 4. RCS = LOW, WSDR = HIGH and RSDR = HIGH. 5. RCLK must be free running for EF to update. D0-D39 WCS WEN WCLK Q0-Q9 EF REN RCLK IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 36 tDS W0 tDH Previous Data tENS tA tA tDS W1 Last Word tREF tENH tDH tDS W2 tDH tDS W3 tDH tENH Last 40-bit Word tSKEW(1) 1 2 tREF tCLKH2 tENS tCLKL2 tCLK2 tA tREF tENH tA W0-W1 5995 drw18 W2-W3 Figure 15. Read Cycle and Empty Flag in x20SDR to x40DDR with Bus-Matching and Rate-Matching (IDT Standard Mode) NOTES: 1. tSKEW1 is the minimum time between a rising WCLK edge and a rising RCLK edge to guarantee that EF will go HIGH (after one RCLK cycle plus tREF). If the time between the rising edge of WCLK and the rising edge of RCLK is less than tSKEW1, then EF deassertion may be delayed one extra RCLK cycle. 2. OE = LOW. 3. First data word latency = tSKEW1 + 1*tRCLK + tREF. 4. RCS = LOW, WCS = LOW, WSDR = LOW and RSDR = HIGH. 5. RCLK must be free running for EF to update. D0-D19 WEN WCLK Q0-Q39 EF REN RCLK NO Read IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 37 tRCSLZ tENS tENS tSKEW1(1) tENH tA 1 tWFF 2 tDS tWFF Wx+1 tDS DATA READ Wx tDH tDH tCLKL2 tCLK2 tENS tSKEW1(1) tENH tA 1 NO WRITE tWFF 2 Wx+3 tDS tWFF Wx+2 tDH NEXT DATA READ tDS 5995 drw19 tDH Figure 16. Write Cycle and Full Flag Timing in x20DDR to x40SDR with Bus-Matching and Rate-Matching (IDT Standard Mode) NOTES: 1. tSKEW1 is the minimum time between a rising RCLK edge and a rising WCLK edge to guarantee that FF will go HIGH (after one WCLK cycle plus tWFF). If the time between the rising edge of the RCLK and the rising edge of the WCLK is less than tSKEW1, then the FF deassertion may be delayed one extra WCLK cycle. 2. LD = HIGH, OE = LOW, EF = HIGH. 3. WCS = LOW. 4. WCLK must be free running for FF to update. Q0-Q39 RCS REN RCLK WEN FF D0-D19 WCLK NO WRITE tCLKH2 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 tRCSLZ tENS tENS tENH tA tA DATA READ tSKEW2(1) 1 NO WRITE tWFF 2 tDS DATA READ Wx tDH tDS tCLK1 tCLKH1 tWFF Wx+1 tDH tENS tENH tA tA NEXT DATA READ tSKEW2(1) NO WRITE 1 tDS tENS NEXT DATA READ tWFF 2 tDH tRCSHZ Wx+2 tDH tWFF Wx+3 tDS 5995 drw20 38 Figure 17. Write Cycle and Full Flag in x40SDR to x20DDR with Bus-Matching and Rate-Matching (IDT Standard Mode) NOTES: 1. tSKEW2 is the minimum time between a falling RCLK edge and a rising WCLK edge to guarantee that FF will go HIGH (after one WCLK cycle plus tWFF). If the time between the falling edge of the RCLK and the rising edge of WCLK is less than tSKEW2, then FF deassertion may be delayed one extra WCLK cycle. 2. OE = LOW, EF = HIGH. 3. WCS = LOW, RCS = LOW, WSDR = HIGH and RSDR = HIGH. 4. WCLK must be free running for FF to update. Q0-Q19 RCS REN RCLK WEN FF D0-D39 WCLK tCLKH1 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES 2 1 RCLK tENS REN tENS tENS tENH tENS RCS tREF tREF EF tRCSLZ Q0 - Qn tRCSHZ tA tRCSLZ tRCSHZ tA LAST DATA-1 LAST DATA tSKEW1(1) WCLK tENS tENH WEN tDS Dn tDH Dx 5995 drw21 NOTES: 1. tSKEW1 is the minimum time between a rising WCLK edge and a rising RCLK edge to guarantee that EF will go HIGH (after one RCLK cycle plus tREF). If the time between the rising edge of WCLK and the rising edge of RCLK is less than tSKEW1, then EF deassertion may be delayed one extra RCLK cycle. 2. First data word latency = tSKEW1 + 1*TRCLK + tREF. 3. OE is LOW. 4. RCLK must be free running for EF to update. Figure 18. Read Cycle and Read Chip Select (IDT Standard Mode) 39 SEPTEMBER 21, 2004 40 W1 W2 1 tENS tSKEW1(1) tDH 2 tRCSLZ W3 PREVIOUS DATA IN OUTPUT REGISTER tDS tENS 3 tREF tA W4 tDS W[n +2] W[n+3] 1 tPAES tSKEW2 (2) 2 W[n+4] W[ D-1 +1 2 ] tDS W[ D-1 +2 2 ] W[ D-1 +3 2 ] W1 W[D-m-2] tDS W[D-m-1] W[D-m] 1 tPAFS W[D-m+1] W[D-m+2] W[D-1] WD 5995 drw22 tWFF tENH Figure 19. Write Timing (FWFT Mode) NOTES: 1. tSKEW1 is the minimum time between a rising WCLK edge and a rising RCLK edge to guarantee that OR will go LOW after two RCLK cycles plus tREF. If the time between the rising edge of WCLK and the rising edge of RCLK is less than tSKEW1, then OR assertion may be delayed one extra RCLK cycle. 2. tSKEW2 is the minimum time between a rising WCLK edge and a rising RCLK edge to guarantee that PAE will go HIGH after one RCLK cycle plus tPAES. If the time between the rising edge of WCLK and the rising edge of RCLK is less than tSKEW2, then the PAE deassertion may be delayed one extra RCLK cycle. 3. OE = LOW 4. n = PAE offset, m = PAF offset and D = maximum FIFO depth. 5. D = 16,385 for IDT72T4088, 32,769 for IDT72T4098, 65,537 for IDT72T40108, 131,073 for IDT72T40118. 6. First data word latency = tSKEW1 + 2*TRCLK + tREF. IR PAF PAE OR Q0 - Qn REN RCS RCLK D0 - Dn WEN WCLK IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 41 tDS tENS W1 tOHZ WD tENS tWFF tDH tENH W1 tOE tA W2 1 (1) tSKEW1 tA 2 tWFF W3 (2) Wm+2 tSKEW2 W[m+3] tA tPAFS W[m+4] W[ 2 D-1 + 1 ] W[ tA 2 D-1 + 2 ] W[D-n-1] tA W[D-n] 1 tPAES W[D-n+1] W[D-n+2] W[D-1] tA tENS WD 5995 drw23 tREF Figure 20. Read Timing (FWFT Mode) NOTES: 1. tSKEW1 is the minimum time between a rising WCLK edge and a rising RCLK edge to guarantee that OR will go LOW after two RCLK cycles plus tREF. If the time between the rising edge of WCLK and the rising edge of RCLK is less than tSKEW1, then OR assertion may be delayed one extra RCLK cycle. 2. tSKEW2 is the minimum time between a rising WCLK edge and a rising RCLK edge to guarantee that PAE will go HIGH after one RCLK cycle plus tPAES. If the time between the rising edge of WCLK and the rising edge of RCLK is less than tSKEW2, then the PAE deassertion may be delayed one extra RCLK cycle. 3. OE = LOW 4. n = PAE offset, m = PAF offset and D = maximum FIFO depth. 5. D = 16,385 for IDT72T4088, 32,769 for IDT72T4098, 65,537 for IDT72T40108, 131,073 for IDT72T40118. 6. First data word latency = tSKEW1 + 2*TRCLK + tREF. IR PAF PAE OR Q0 - Qn OE REN RCLK D0 - Dn WEN WCLK IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 42 tDS tENS W1 WD tENS tRCSHZ tENH tENS tWFF tDH tENH W2 tRCSLZ 1 (1) tSKEW1 tA 2 tWFF W3 (2) Wm+2 tSKEW2 W[m+3] tA tPAFS W[m+4] W [ D-1 2 + 1] W [ D-1 2 + 2] tA W[D-n-1] tA W[D-n] 1 tPAES W[D-n+1] W[D-n+2] W[D-1] tA tENS WD 5995 drw24 tREF Figure 21. Read Cycle and Read Chip Select Timing (FWFT Mode) NOTES: 1. tSKEW1 is the minimum time between a rising RCLK edge and a rising WCLK edge to guarantee that IR will go LOW after one WCLK cycle plus tWFF. If the time between the rising edge of RCLK and the rising edge of WCLK is less than tSKEW1, then the IR assertion may be delayed one extra WCLK cycle. 2. tSKEW2 is the minimum time between a rising RCLK edge and a rising WCLK edge to guarantee that PAF will go HIGH after one WCLK cycle plus tPAFS. If the time between the rising edge of RCLK and the rising edge of WCLK is less than tSKEW2, then the PAF deassertion may be delayed one extra WCLK cycle. 3. n = PAE Offset, m = PAF offset and D = maximum FIFO depth. 4. D = 16,385 for IDT72T4088, 32,769 for IDT72T4098, 65,537 for IDT72T40108, 131,073 for IDT72T40118. 5. OE = LOW. 6. RCLK must be free running for EF to update. IR PAF PAE OR Q0 - Qn RCS REN RCLK D0 - Dn WEN WCLK IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 HIGH-Z tDS tENS W1 tDH tSKEW tDS 1 W2 tDH tENH 2 tREF 3 1st Word falls through to O/P register on this cycle tENS tRCSLZ W1 tENS tA tENH W2 tENS tRCSHZ tENH tENS tENS tRCSLZ tREF W2 5995 drw25 43 Figure 22 . RCS and REN Read Operation (FWFT Mode) NOTES: 1. It is very important that the REN be held HIGH for at least one cycle after RCS has gone LOW. If REN goes LOW on the same cycle as RCS or earlier, then Word, W1 will be lost, Word, W2 will be read on the output when the bus goes to LOW-Z. 2. The 1st Word will fall through to the output register regardless of REN and RCS. However, subsequent reads require that both REN and RCS be active, LOW. 3. RCS functions similarly to OE, when RCS is HIGH the read pointer will not increment. Dn WEN WCLK Qn OR RCS REN RCLK IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 44 WMK tENS tENH tA WMK+2 tA WMK+1 tA WMK+3 tA WMK+4 tENS tA WMK+6 tA WMK+5 tENS tSKEW2 tREF tENH 1 tREF WMK+n tCLK2 tENS Figure 23 . Retransmit from MARK in Double Data Rate Mode (IDT Standard Mode) tPAFS 2 tCLKL2 NOTES: 1. Retransmit setup is complete when EF returns HIGH. 2. OE = LOW;RCS = LOW. 3. RT must be HIGH when reading from FIFO. 4. Once MARK is set, the write pointer will not increment past the `marked' location, preventing overwrites of Retransmit data. 5. Before a "MARK" can be set there must be at least 160 bytes of data between the Write Pointer and Read Pointer locations. (160 bytes = 16 words = 8 long words). 6. RCLK must be free running for EF to update. 7. A transition in the PAE flag may not occur until one RCLK cycle later than shown. 8. In DDR mode the MARK function will "MARK" words only on even word boundaries (i.e. Rising edge of RCLK). PAF WCLK PAE EF RT MARK Q0-Qn REN RCLK 1 tCLKH2 tPAES(7) tA 2 tA WMK tA WMK+1 tA 5995 drw26 WMK+2 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 45 WMK-1 tENS tA tENS WMK tENH tA WMK+1 tA tA tENS tENS tENS WMK+n 1 tSKEW2 tREF tENH 2 tPAFS tA 1 tREF Figure 24. Retransmit from Mark (FWFT Mode) NOTES: 1. Retransmit setup is complete when OR returns LOW. 2. OE = LOW;RCS = LOW. 3. RT must be HIGH when reading from FIFO. 4. Once MARK is set, the write pointer will not increment past the `marked' location, preventing overwrites of Retransmit data. 5. Before a "MARK" can be set there must be at least 160 bytes of data between the Write Pointer and Read Pointer locations. (160 bytes = 16 words = 8 long words). 6. RCLK must be free running for EF to update. 7. A transition in the PAE flag may not occur until one RCLK cycle later than shown. PAF WEN WCLK PAE OR RT MARK Qn REN RCLK WMK tENS tA 2 tPAES(7) WMK+1 tA 5995 drw27 WMK+2 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 tSCKH COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES tSCLK tSCKL SCLK tSENH tSENS tENH SEN tSDH tSDS (1) BIT 1 SI (1) BIT 1 BIT X BIT X EMPTY OFFSET 5995 drw28 FULL OFFSET NOTE: 1. In SDR mode, X = 14 for the IDT72T4088, X = 15 for the IDT72T4098, X = 16 for the IDT72T40108, X = 17 for the IDT72T40118. 2. In DDR mode, X = 13 for the IDT72T4088, X = 14 for the IDT72T4098, X = 15 for the IDT72T70108, X = 16 for the IDT72T40118. Figure 25. Loading of Programmable Flag Registers (IDT Standard and FWFT Modes) tSCKH tSCLK tSCKL SCLK tSENH tSENS tENH SREN tSOA tSOA SO (1) BIT 0 BIT X (1) BIT 0 EMPTY OFFSET BIT X FULL OFFSET 5995 drw29 NOTE: 1. In SDR mode, X = 14 for the IDT72T4088, X = 15 for the IDT72T4098, X = 16 for the IDT72T40108, X = 17 for the IDT72T40118. 2. In DDR mode, X = 13 for the IDT72T4088, X = 14 for the IDT72T4098, X = 15 for the IDT72T40108, X = 16 for the IDT72T40118. 3. Offset register values are always read starting from the first location in the offset register upon initiating SREN. Figure 26. Reading of Programmable Flag Registers (IDT Standard and FWFT Modes) 46 SEPTEMBER 21, 2004 tOLZ tENS WD-10 tA tCLKEN tERCLK WD-9 tA WD-8 tA tENH WD-7 tA WD-6 tOLZ tCLKEN tOLZ tCLKEN tENS WD-6 tA WD-5 tA WD-4 tA tENH WD-3 tA WD-2 tCLKEN tENS tA tREF tCLKEN tA WD-1 47 EF 1 1 1 1 0 RCLK 0 0 1 1 X RCS 0 1 0 1 X REN Figure 27. Echo Read Clock & Read Enable Operation in Double Data Rate Mode (IDT Standard Mode Only) 0 1 1 1 1 EREN Last Word WD tCLKEN NO Read NOTES: 1. The EREN output is "or gated" to RCS and REN and will follow these inputs provided that the FIFO is not empty. If the FIFO is empty, EREN will go HIGH to indicate that there is no new word available. 2. The EREN output is synchronous to RCLK. 3. OE = LOW. 4. The truth table for EREN is shown below: Qn EF EREN RCS REN ERCLK RCLK NO Read 5995 drw30 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES WCLK tENS tENH WEN tDS tDH tDS Wn+1 D0 - Dn tDH tDS Wn+2 tDH Wn+3 tSKEW1 1 RCLK 2 b a e d c h g f i tERCLK ERCLK tENS REN tENH tENS RCS tCLKEN tCLKEN tCLKEN tCLKEN EREN tRCSLZ HIGH-Z Qn tA tA Wn+1 Wn+2 Wn+3 tREF tREF OR tA tA O/P Reg. Wn Last Word Wn+1 tA Wn+2 Wn+3 5995 drw31 NOTE: 1. The O/P Register is the internal output register. Its contents are available on the Qn output bus only when RCS and OE are both active, LOW, that is the bus is not in HighImpedance state. 2. OE is LOW. Cycle: a&b. At this point the FIFO is empty, OR is HIGH. RCS and REN are both disabled, the output bus is High-Impedance. c. Word Wn+1 falls through to the output register, OR goes active, LOW. RCS is HIGH, therefore the Qn outputs are High-Impedance. EREN goes LOW to indicate that a new word has been placed on the output register. d. EREN goes HIGH, no new word has been placed on the output register on this cycle. e. No Operation. f. RCS is LOW on this cycle, therefore the Qn outputs go to Low-Impedance and the contents of the output register (Wn+1) are made available. NOTE: In FWFT mode is important to take RCS active LOW at least one cycle ahead of REN, this ensures the word (Wn+1) currently in the output register is made available for at least one cycle. g. REN goes active LOW, this reads out the second word, Wn+2. EREN goes active LOW to indicate a new word has been placed into the output register. h. Word Wn+3 is read out, EREN remains active, LOW indicating a new word has been read out. NOTE: Wn+3 is the last word in the FIFO. i. This is the next enabled read after the last word, Wn+3 has been read out. OR flag goes HIGH and EREN goes HIGH to indicate that there is no new word available. 3. OE is LOW. 4. The truth table for EREN is shown below: RCLK OR RCS REN EREN 0 0 0 0 1 0 0 1 1 X 0 1 0 1 X 0 1 1 1 1 Figure 28. Echo RCLK and Echo REN Operation (FWFT Mode Only) 48 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 tCLKL1 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES tCLKH1 WCLK 1 2 1 tENS 2 tENH WEN tPAFS PAF tPAFS (2) D-(m+1) words (2) in FIFO D - m words in FIFO (2) D - (m +1) words in FIFO (3) tSKEW3 RCLK tENH tENS REN 5995 drw32 NOTES: 1. m = PAF offset. 2. D = maximum FIFO Depth. In IDT Standard Mode: D=16,384 for the IDT72T4088, 32,768 for the IDT72T4098, 65,536 for the IDT72T40108, 131,072 for the IDT72T40118. In FWFT Mode: D=16,385 for the IDT72T4088, 32,769 for the IDT72T4098, 65,537 for the IDT72T40108, 131,073 for the IDT72T40118. 3. PAF is asserted and updated on the rising edge of WCLK only. 4. tSKEW3 is the minimum time between a rising RCLK edge and a rising WCLK edge to guarantee that PAF will go HIGH (after one WCLK cycle plus tPAFS). If the time between the rising edge of RCLK and the rising edge of WCLK is less than tSKEW3, then the PAF deassertion time may be delayed one extra WCLK cycle. 5. RCS = LOW. Figure 29. Programmable Almost-Full Flag Timing (IDT Standard and FWFT Modes) tCLKH1 tCLKL1 WCLK tENS tENH WEN (2) PAE (2) n words in FIFO , (3) n + 1 words in FIFO (4) tSKEW3 RCLK 1 n words in FIFO , (3) n + 1 words in FIFO (2) n + 1 words in FIFO , (3) n + 2 words in FIFO tPAES 2 tPAES 1 tENS 2 tENH REN 5995 drw33 NOTES: 1. n = PAE offset. 2. For IDT Standard Mode. 3. For FWFT Mode. 4. PAE is asserted and updated on the rising edge of RCLK only. 5. tSKEW3 is the minimum time between a rising WCLK edge and a rising RCLK edge to guarantee that PAE will go HIGH (after one RCLK cycle plus tPAES). If the time between the rising edge of WCLK and the rising edge of RCLK is less than tSKEW3, then the PAE deassertion may be delayed one extra RCLK cycle. 5. PAE is asserted and updated on the rising edge of RCLK only. 6. RCS = LOW. Figure 30. Programmable Almost-Empty Flag Timing (IDT Standard and FWFT Modes) 49 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES avoided by creating composite flags, that is, ANDing EF of every FIFO, and separately ANDing FF of every FIFO. In FWFT mode, composite flags can be created by ORing OR of every FIFO, and separately ORing IR of every FIFO. Figure 31 demonstrates a width expansion using two IDT72T4088/ 72T4098/72T40108/72T40118 devices. D0 - D40 from each device form a 80bit wide input bus and Q0-Q39 from each device form a 80-bit wide output bus. Any word width can be attained by adding additional IDT72T4088/72T4098/ 72T40108/72T40118 devices. OPTIONAL CONFIGURATIONS WIDTH EXPANSION CONFIGURATION Word width may be increased simply by connecting together the control signals of multiple devices. Status flags can be detected from any one device. The exceptions are the EF and FF functions in IDT Standard mode and the IR and OR functions in FWFT mode. Because of variations in skew between RCLK and WCLK, it is possible for EF/FF deassertion and IR/OR assertion to vary by one cycle between FIFOs. In IDT Standard mode, such problems can be SERIAL CLOCK (SCLK) PARTIAL RESET (PRS) MASTER RESET (MRS) FIRST WORD FALL THROUGH (FWFT) RETRANSMIT (RT) Dm+1 - Dn m+n DATA IN D0 - Dm m n READ CLOCK (RCLK) READ CHIP SELECT (RCS) WRITE CLOCK (WCLK) READ ENABLE (REN) WRITE ENABLE (WEN) FULL FLAG/INPUT READY (FF/IR) #1 IDT 72T4088 72T4098 72T40108 72T40118 IDT 72T4088 72T4098 72T40108 72T40118 PROGRAMMABLE (PAE) EMPTY FLAG/OUTPUT READY (EF/OR) #1 (1) GATE OUTPUT ENABLE (OE) FULL FLAG/INPUT READY (FF/IR) #2 PROGRAMMABLE (PAF) (1) GATE EMPTY FLAG/OUTPUT READY (EF/OR) #2 FIFO #1 FIFO #2 m n Qm+1 - Qn m+n DATA OUT 5995 drw34 Q0 - Qm NOTES: 1. Use an AND gate in IDT Standard mode, an OR gate in FWFT mode. 2. Do not connect any output control signals directly together. 3. FIFO #1 and FIFO #2 must be the same depth, but may be different word widths. Figure 31. Block Diagram of 16,384 x 80, 32,768 x 80, 65,536 x 80, 131,072 x 80 Width Expansion 50 SEPTEMBER 21, 2004 IDT72T4088/98/108/118 2.5V HIGH-SPEED TeraSyncTM DDR/SDR FIFO 40-BIT CONFIGURATION 16,384 x 40, 32,768 x 40, 65,536 x 40 and 131,072 x 40 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES FWFT TRANSFER CLOCK WRITE CLOCK WRITE ENABLE INPUT READY FWFT WCLK WEN IR FWFT RCLK IDT 72T4088 72T4098 72T40108 72T40118 OR IR RCS n Dn WEN REN OE DATA IN WCLK Qn GND n READ CLOCK RCLK IDT 72T4088 72T4098 72T40108 72T40118 RCS READ CHIP SELECT READ ENABLE REN OR OUTPUT READY OE OUTPUT ENABLE n Dn DATA OUT Qn 5995 drw35 Figure 32. Block Diagram of 32,768 x 40, 65,536 x 40, 131,072 x 40, 262,144 x 40 Depth Expansion in Single Data Rate Mode DEPTH EXPANSION CONFIGURATION IN SINGLE DATA RATE (FWFT MODE ONLY) The IDT72T4088 can easily be adapted to applications requiring depths greater than 16,384, 32,768 for the IDT72T4098, 65,536 for the IDT72T40108, 131,072 for the IDT72T40118 with an 40-bit bus width. In FWFT mode, the FIFOs can be connected in series (the data outputs of one FIFO connected to the data inputs of the next) with no external logic necessary. The resulting configuration provides a total depth equivalent to the sum of the depths associated with each single FIFO. Figure 32 shows a depth expansion using two IDT72T4088/72T4098/72T40108/72T40118 devices. Care should be taken to select FWFT mode during Master Reset for all FIFOs in the depth expansion configuration. Also, the devices must be operating in Single Data Rate mode since that is the only mode available in FWFT. The first word written to an empty configuration will pass from one FIFO to the next ("ripple down") until it finally appears at the outputs of the last FIFO in the chain - no read operation is necessary but the RCLK of each FIFO must be free-running. Each time the data word appears at the outputs of one FIFO, that device's OR line goes LOW, enabling a write to the next FIFO in line. For an empty expansion configuration, the amount of time it takes for OR of the last FIFO in the chain to go LOW (i.e. valid data to appear on the last FIFO's outputs) after a word has been written to the first FIFO is the sum of the delays for each individual FIFO: specification is not met between WCLK and transfer clock, or RCLK and transfer clock, for the OR flag. The "ripple down" delay is only noticeable for the first word written to an empty depth expansion configuration. There will be no delay evident for subsequent words written to the configuration. The first free location created by reading from a full depth expansion configuration will "bubble up" from the last FIFO to the previous one until it finally moves into the first FIFO of the chain. Each time a free location is created in one FIFO of the chain, that FIFO's IR line goes LOW, enabling the preceding FIFO to write a word to fill it. For a full expansion configuration, the amount of time it takes for IR of the first FIFO in the chain to go LOW after a word has been read from the last FIFO is the sum of the delays for each individual FIFO: (N - 1)*(3*transfer clock) + 2 TWCLK where N is the number of FIFOs in the expansion and TWCLK is the WCLK period. Note that extra cycles should be added for the possibility that the tSKEW1 specification is not met between RCLK and transfer clock, or WCLK and transfer clock, for the IR flag. The Transfer Clock line should be tied to either WCLK or RCLK, whichever is faster. Both these actions result in data moving, as quickly as possible, to the end of the chain and free locations to the beginning of the chain. (N - 1)*(4*transfer clock) + 3*TRCLK where N is the number of FIFOs in the expansion and TRCLK is the RCLK period. Note that extra cycles should be added for the possibility that the tSKEW1 51 SEPTEMBER 21, 2004 ORDERING INFORMATION IDT XXXXX X XX X Device Type Power Speed Package X Process / Temperature Range BLANK I(1) Commercial (0C to +70C) Industrial (-40C to +85C) BB Plastic Ball Grid Array (PBGA, BB208-1) 4 5 6-7 10 Commercial Only Commercial Only Commercial and Industrial Commercial Only L Low Power 72T4088 72T4098 72T40108 72T40118 16,384 x 40 32,768 x 40 65,536 x 40 131,072 x 40 Clock Cycle Time (tCLK) Speed in Nanoseconds 2.5V High-Speed TeraSyncTM DDR/SDR FIFO 2.5V High-Speed TeraSyncTM DDR/SDR FIFO 2.5V High-Speed TeraSyncTM DDR/SDR FIFO 2.5V High-Speed TeraSyncTM DDR/SDR FIFO 5995 drw36 NOTE: 1. Industrial temperature range product is available for 6-7ns as a standard product. All other speed grades are available by special order. DATASHEET DOCUMENT HISTORY 03/01/2002 04/08/2002 04/24/2002 05/24/2002 11/21/2002 02/11/2003 03/20/2003 12/17/2003 09/21/2004 pgs. pgs. pgs. pgs. pgs. pgs. pgs. pgs. pgs. 1, 4, 6, 8, 9, and 23. 1, 8, 9, 11, 33-37, 42, 46-48, and 51. 19, and 28. 6-9, and 12. 1, and 10. 7, 8, and 27. 25, 27, 28, and 44. 10, 31-34, 36-38, 44, and 49. 1, 3, 9-11, 17, and 28. CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 52 for Tech Support: 408-330-1753 email: FIFOhelp@idt.com