Revision 4-24-2017
- 1 of 10 -
Disclaimer: Subject to change without notice
© 2017 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
RFMD + TriQuint = Qorvo
QPC6034
Absorptive High Isolation SP3T Switch
5 MHz to 6000 MHz
The QPC6034 is a Silicon on Insulator (SOI) single-pole, 3-throw
(SP3T) switch, designed for use in cellular, 3G, LTE, and other
high performance communications systems. It offers high
isolation symmetric topology with excellent linearity and power
handling capability. No blocking capacitors are necessary on the
RF ports. The design is non-reflective such that the RFX ports
are terminated into 50 Ω in the off state. QPC6034 is +1.8 V logic
compatible, and incorporates a single pin to disable the internal
Negative Voltage Generator (NVG) and supply a negative
voltage from off-chip, if necessary.
Package: QFN, 24-pin,
4.0 mm x 4.0 mm
Applications
Cellular, 3G, LTE Infrastructure
WiBro, WiMAX, LTE
High Performance Communications
Systems
Test Equipment
Features
5 MHz to 6000 MHz Operation
Symmetrical SP3T.
Non-Reflective (RFX ports)
Terminated All-Off State mode
No Blocking Caps Necessary unless
voltage is on RF Line
High Isolation: 62 dB at 2 GHz
High Input IP3: +59 dBm
2 kV ESD
+1.8 V Logic Compatible
Functional Block Diagram
24
GND
GND
GND
GND
GND
GND
V2
V1
VDD
GND
RF1
GND
GND
RF3
GND
GND
RF2
GND
GND
GND
RFC
GND
VSS/GND
GND
Logic/
Control
Pin 1
Mark
23 22 21 20 19
1
2
3
4
5
6
18
17
16
15
14
13
7 8 9 10 11 12
Ordering Information
QPC6034SQ
Sample Bag with 25 pieces
QPC6034SR
7" Reel with 100 pieces
QPC6034TR13
13" Reel with 2500 pieces
QPC6034PCK401
5 MHz to 6000 MHz PCBA with 5-Piece Sample Bag
Revision 4-24-2017
- 2 of 10 -
Disclaimer: Subject to change without notice
© 2017 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPC6034
RFMD + TriQuint = Qorvo
Absolute Maximum Ratings
Parameter
Rating
Units
Supply Voltage
+6
V
Control Voltage
-0.2 to +6
V
VSS Supply
−6
V
Max RF Input Power, RFC/RFX non-
terminated
+37.5
dBm
Max RF Input Power, RFX terminated
+29
dBm
Operating Temperature
−40 to +105
°C
Storage Temperature
−40 to +150
°C
Maximum Junction Temperature
+125
°C
ESD Rating
Human Body Model (HBM)
2000
V
Charge Device Model (CDM)
1000
Moisture Sensitivity Level (MSL) Rating
2
–
Caution! ESD sensitive device.
RFMD Green: RoHS status based on EU Directive
2011/65/EU (at time of this document revision), halogen
free per IEC 61249-2-21, < 1000 ppm each of antimony
trioxide in polymeric materials and red phosphorus as a
flame retardant, and <2% antimony in solder.
Exceeding any one or a combination of the Absolute Maximum Rating
conditions may cause permanent damage to the device. Extended
application of Absolute Maximum Rating conditions to the device may
reduce device reliability. Specified typical performance or functional -
operation of the device under Absolute Maximum Rating conditions is not
implied.
Recommended Operating Conditions
Parameter
Specifications
Units
Min
Typ
Max
Operating Temperature Range
−40
+25
+105
°C
Operating Junction Temperature
+125
°C
Supply Voltage
+2.7
+5.0
+5.5
V
VSS Supply (Applicable for off-chip negative supply, otherwise
0V (zero) for internal NVG operation)
−5.5
−5.0
−2.7
V
Electrical Specifications
Parameter
Specification
Units
Conditions
Min
Typ
Max
Operating Frequency Range
5
6000
MHz
Insertion Loss
0.84
dB
450 MHz
0.86
dB
900 MHz
0.93
1.25
dB
2100 MHz
0.96
dB
2600 MHz
0.98
dB
4000 MHz
1.00
dB
6000 MHz
Isolation (RFC – RFX)
75
dB
450 MHz
70
dB
900 MHz
50
62
dB
2100 MHz
61
dB
2600 MHz
61
dB
4000 MHz
60
dB
6000 MHz
Test conditions unless otherwise specified: TA = +25 °C, VCTRL = 0/+5 V, VDD = +5 V, 50 Ω system, Standard Application Circuit
Revision 4-24-2017
- 3 of 10 -
Disclaimer: Subject to change without notice
© 2017 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPC6034
RFMD + TriQuint = Qorvo
Electrical Specifications (contd.)
Parameter
Specification
Units
Conditions
Min
Typ
Max
Isolation (RFX – RFX)
78
dB
450 MHz
73
dB
900 MHz
65
dB
2100 MHz
62
dB
2600 MHz
55
dB
4000 MHz
48
dB
6000 MHz
Return Loss (RFX On-State)
29
dB
450 MHz
27
dB
900 MHz
24
dB
2100 MHz
24
dB
2600 MHz
20
dB
4000 MHz
14
dB
6000 MHz
Return Loss (RFX Off-State)
29
dB
450 MHz
27
dB
900 MHz
30
dB
2100 MHz
25
dB
2600 MHz
30
dB
4000 MHz
16
dB
6000 MHz
Input IP2
+110
dBm
1 GHz
Input IP3
+55
+59
dBm
1 GHz, +17 dBm/tone, 1 MHz tone spacing
Input P1dB
+36
dBm
Settling Time
1
4
µs
50% VCTRL to optimum functionality
Start-up Time
5
25
µs
90% VDD to full functionality
Switching Speed
150
500
ns
50 % control to 10/90 % RF
NVG Spur
-104
dBm
Internal NVG on.
Test conditions unless otherwise specified: TA = +25 °C, VCTRL = 0/+5 V, VDD = +5 V, 50 Ω system, Standard Application Circuit
Electrical Specifications – Power Supply
Parameter
Specification
Units
Conditions
Min
Typ
Max
Supply Current (IDD)
90
μA
VDD = +5 V
Control Current (V1, V2)
1
μA
VCTRL = +5 V
VSS Current
100
μA
VSS = −5 V, NVG is shut down.
Low Control Voltage (V1, V2)
0
+0.63
V
+1.8 V Logic Compatible
High Control Voltage (V1, V2)
+1.1
VDD
V
+1.8 V Logic Compatible
Test conditions unless otherwise specified: TA = +25 °C, VCTRL = 0/+5 V, VDD = +5 V, 50 Ω system, Standard Application Circuit
Revision 4-24-2017
- 4 of 10 -
Disclaimer: Subject to change without notice
© 2017 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPC6034
RFMD + TriQuint = Qorvo
Maximum Operating Power at High Temperature, CW, ≥50 MHz, 50 Ω System
Input
Power (dBm) at each port
Theta-J (°C/W)
+85°C
+105°C
RFC/ RFX – Active 1
35.4
32.2
56
RFX – Terminated (1 path)
27.8
24.8
66
RFX – Terminated (2 adjacent paths)
26.7
23.7
85
RFX – Terminated (all paths)
26.6
23.6
86
Notes:
1. For frequencies <50 MHz, maximum operating power at all temperatures should be at least 2 dB less than P1dB compression
from plot.
Truth Table
MODE
V1
V2
All Termination State (All Off)
0
0
RFC-RF1 Active
1
0
RFC-RF2 Active
0
1
RFC-RF3 Active
1
1
Typical Performance
Revision 4-24-2017
- 7 of 10 -
Disclaimer: Subject to change without notice
© 2017 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPC6034
RFMD + TriQuint = Qorvo
Evaluation Board Schematic and PCB – 5MHz to 6000 MHz Application Circuit
Note:
The QPC6064-410 PCB is used within the family of QPC60x4 products based on the individual BOM per product.
Evaluation Board Bill of Materials (BOM) - 5 MHz to 6000 MHz Application Circuit
Description
Reference Designator
Manufacturer
Manufacturer's P/N
Evaluation Board
–
Viasystems Technologies Corp.
QPC6064-410(B)
QPC6034
U1
RFMD / Qorvo
QPC6034
CAP, 100 pF, 5 %, 50 V, COG, 0402
C1-C5
Taiyo Yuden
RM UMK105CG101JV-F
CONN, SMA EL FLT VIPER, MAT-21-1038
J1 – J3, J6
Amphenol RF Asia Corp
901-10425
CONN, HDR, ST, PLRZD, 6-PIN
P1
AMP
640454-6
Revision 4-24-2017
- 8 of 10 -
Disclaimer: Subject to change without notice
© 2017 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPC6034
RFMD + TriQuint = Qorvo
Pin Configuration and Description
1
2
3
4
5
6
18
17
16
15
14
13
121110987
192021222324
GND
GND
GND
GND
GND
GND
V2
V1
VDD
GND
RF1
GND
GND
RF3
GND
GND
RF2
GND
GND
GND
RFC
GND
VSS/
GND
GND
Pin1 Mark
Backside Pad
Top view
Pin
Label
Description
1 – 7, 9, 10, 12, 13,
15, 19, 21, 23, 24
GND
Connect to Low inductive Path to Ground
8
RF3
RF Port 3
11
RF2
RF Port 2
14
RF1
RF Port 1
16
VDD
Supply Voltage
17
V1
Control Pin
18
V2
Control Pin
20
VSS/GND
Negative Voltage Generator (NVG) control pin. Supply GND (Low inductive path to ground) to
enable internal NVG or supply −2.7 V to −5 V to disable internal NVG. Once disabled, internal
NVG cannot be enabled without cycling VDD.
22
RFC
RF Common Port
Backside Pad
GND
Connect to Low inductive Path to Ground
Revision 4-24-2017
- 9 of 10 -
Disclaimer: Subject to change without notice
© 2017 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPC6034
RFMD + TriQuint = Qorvo
Package Marking
Package Outline (Dimensions in millimeters)
4.00
4.00
0.10 C A B
A
B
PIN 1 INDICATOR
2.70
2.70
0.10 A B C
0.05 C
0.05 C
0.50
24x 0.25
24x 0.40
3x (R0.08)
SEATING PLANE
C
(0.250)
(0.750±0.05)
(0.050)
(0.203) PIN #1 IDENTIFICATION
CHAMFER 0.300 X 45°
R0.08 CHAMFER 0.09 X 45°
Revision 4-24-2017
- 10 of 10 -
Disclaimer: Subject to change without notice
© 2017 Qorvo, Inc.
www.rfmd.com / www.qorvo.com
QPC6034
RFMD + TriQuint = Qorvo
PCB/ PCB Soldermask/ PCB Stencil Drawing (Dimensions in millimeters)
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Web: www.rfmd.com Tel: 1-844-890-8163
Email: customer.support@qorvo.com
For information about the merger of RFMD and TriQuint as Qorvo:
Web: www.qorvo.com
Important Notice
The information contained herein is believed to be reliable. RFMD makes no warranties regarding the information contained
herein. RFMD assumes no responsibility or liability whatsoever for any of the information contained herein. RFMD assumes
no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is
provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user.
All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant
information before placing orders for RFMD products. The information contained herein or any use of such information
does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether
with regard to such information itself or anything described by such information.
RFMD products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining
applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death.
