ALUMINUM ELECTROLYTIC CAPACITORS UN Chip Type, Bi-Polarized, Higher Capacitance Range series Chip Type ,higher capacitance in larger case sizes (12.5, 16, 18, 20) Designed for surface mounting on high density PC board. Bi-polarized series for operations over wide temperature range of - 55 to +105C. Applicable to automatic mounting machine fed with carrier tape and tray. Compliant to the RoHS directive (2002/95/EC). UN Bi-polarized UJ Specifications Item Performance Characteristics Category Temperature Range - 55 to +105C Rated Voltage Range 6.3 to 100V Rated Capacitance Range 22 to 3300F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4 (A), whichever is greater. Measurement frequency : 120Hz, Temperature : 20C Rated voltage (V) tan (MAX.) Tangent of loss angle (tan ) 6.3 0.26 10 0.22 16 0.18 25 0.16 35 0.14 50 0.12 63 0.10 100 0.09 For capacitance of more than 1000F, add 0.02 for every increase of 1000F. Measurement frequency: 120Hz Rated voltage (V) Z- 25C / Z+20C Impedance ratio ZT / Z20 (MAX.) Z- 40C / Z+20C Stability at Low Temperature 50 2 3 35 2 3 25 2 4 16 3 6 10 4 8 6.3 5 10 63 2 3 100 2 3 Endurance The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 105C with the polarity inverted every 250 hours. Shelf Life After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. Marking Black print on the case top. Chip Type C 0.2 0.3 MAX. A 0.2 A 0.2 Pressure relief vent Series 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UUN 1 H 3 3 1 M NQ 1 MS Package code Taping MS Tray ZD E B 0.2 D 0.5 BP 330 F UN 50V H0515 Lot No. 0.5 MAX. Plastic platform Voltage nichicon Within 20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value Type numbering system (Example : 50V 330F) Trade mark Capacitance Capacitance change tan Leakage current L 1.0 Size code Configuration Capacitance Tolerance(20%) H Rated capacitance(330F) Rated voltage(50V) D Code 12.5 to 18 NQ 20 RQ Series name (mm) Type D 12.5x13.5 12.5x16. 16x16.5. 16 x 21.5. 18x16.5. 18 x 21.5. 20 x 21.5. 4.8 4.8 5.4 5.4 6.4 6.4 6.2 A 13.6 13.6 17.1 17.1 19.1 19.1 21.1 B 13.6 13.6 17.1 17.1 19.1 19.1 21.1 C 4.0 4.0 6.3 6.3 6.3 6.3 8.8 E 13.5 16.0 16.5 21.5 16.5 21.5 21.5 L H 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.3 to 1.7 Dimension table in next page. CAT.8100Y ALUMINUM ELECTROLYTIC CAPACITORS UN series Dimensions V (F) Code Cap. 22 220 33 330 47 470 100 101 220 221 330 331 470 471 1000 102 6.3 10 16 25 35 50 63 0J 1A 1C 1E 1V 1H 1J 12.5 x 13.5 12.5 x 13.5 2200 3300 222 332 310 16 x 16.5 270 370 12.5 x 13.5 270 12.5 x 13.5 340 16 x 16.5 420 16 x 16.5 490 12.5 x 16 500 16 x 16.5 600 18 x 16.5 670 18 x 21.5 780 16 x 21.5 670 18 x 16.5 740 16 x 21.5 740 18 x 21.5 920 18 x 21.5 12.5 x 13.5 180 16 x 16.5 330 18 x 16.5 450 16 x 21.5 450 18 x 21.5 590 100 2A 12.5 x 13.5 100 12.5 x 16 150 12.5 x 13.5 130 12.5 x 13.5 140 16 x 16.5 180 12.5 x 16 230 16 x 16.5 270 18 x 21.5 310 18 x 16.5 400 18 x 21.5 440 16 x 21.5 400 18 x 21.5 540 20 x 21.5 590 20 x 21.5 640 Case size D x L (mm) Rated ripple 830 Rated ripple current (mArms) at 105C 120Hz In this case, 6 will be put at 12th digit of type numbering system, " " Frequency coefficient of rated ripple current Cap.(F) Frequency 0 less than 470 100 to 470 1000 to 3300 50 Hz 0.75 0.80 0.85 120 Hz 1.00 1.00 1.00 300 Hz 1.35 1.23 1.10 1 kHz 1.57 1.34 1.13 10 kHz or more 2.00 1.50 1.15 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100Y