Document Number: EN0556EJ3V0DS00 (3rd edition)
Published date: March 2002 N CP(N)
ã NEC Corporation
2002 All rights reserved.
All information is subject to change without notice.
TFT COLOR LCD MODULE
NL3224BC35-20
13.9cm (5.5 Type)
QVGA
DATA SHEET
(3rd edition)
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 2
INTRODUCTION
No part of this document shall be copied in any form or by any means without the prior written consent
of NEC Corporation.
NEC Corporation does not assume any liability for infringement of patents, copyrights or other
intellectual property rights of third parties by or arising from use of a product described herein or any
other liability arising from use of such application. No license, express, implied or otherwise, is granted
under any patents, copyrights or other intellectual property rights of NEC Corporation or of others.
While NEC Corporation has been making continuous effort to enhance the reliability of its products, the
possibility of failures cannot be eliminated entirely. To minimize risks of damage to property or injury to
person arising from a failure in an NEC product, customers must incorporate sufficient safety measures
in their design, such as redundancy, fire-containment and anti-failure features.
NEC products are classified into the following three quality grades:
"Standard", "Special", "Specific"
The "Specific" quality grade applies only to applications developed based on a customer designated
"quality assurance program" for a specific application. The recommended applications of a product
depend on its quality grade, as indicated below. Customers must check the quality grade of each
application before using it in a particular application.
Standard: Computers, office equipment, communications equipment, test and measurement equipment,
audio and visual equipment, home electronic appliances, machine tools, personal electronic
equipment and industrial robots
Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically
designed for life support)
Specific: Military systems, aircraft, aerospace equipment, submersible repeaters, nuclear reactor control
systems, life support systems (medical equipment, etc.) and any other equipment
The quality grade of this product is "Standard" unless otherwise specified in this document. If
customers intend to use this product for applications other than those specified for "Standard" quality
grade, they should contact NEC Corporation sales representative in advance.
Anti-radioactive design is not implemented in this product.
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 3
CONTENTS
INTRODUCTION.......................................................................................................................................... 2
1. OUTLINE ................................................................................................................................................... 5
1.1 STRUCTURE AND PRINCIPLE.......................................................................................................... 5
1.2 APPLICATIONS .................................................................................................................................... 5
1.3 FEATURES............................................................................................................................................ 5
2. GENERAL SPECIFICATIONS................................................................................................................ 6
3. BLOCK DIAGRAM .................................................................................................................................. 7
4. DETAILED SPECIFICATIONS............................................................................................................... 8
4.1 MECHANICAL SPECIFICATIONS ..................................................................................................... 8
4.2 ABSOLUTE MAXIMUM RATINGS....................................................................................................8
4.3 ELECTRICAL CHARACTERISTICS ..................................................................................................9
4.3.1 Driving for LCD panel signal processing board ........................................................................... 9
4.3.2 Working for backlight lamp........................................................................................................... 9
4.3.3 Power supply voltage ripple........................................................................................................ 10
4.3.4 Fuse ............................................................................................................................................. 10
4.4 POWER SUPPLY VOLTAGE SEQUENCE.........................................................................................11
4.4.1 Sequence for LCD panel signal processing board........................................................................11
4.4.2 Sequence for backlight inverter (Option).....................................................................................11
4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS........................................................ 12
4.5.1 LCD panel signal processing board ............................................................................................ 12
4.5.2 Backlight lamp ............................................................................................................................ 13
4.5.3 Positions of plugs and a socket ................................................................................................... 13
4.6 DISPLAY COLORS AND INPUT DATA SIGNALS.......................................................................... 14
4.7 DISPLAY POSITIONS ........................................................................................................................ 15
4.8 SCANNING DIRECTIONS ................................................................................................................ 15
4.8.1 QVGA display mode ................................................................................................................... 15
4.8.2 VGA display mode ...................................................................................................................... 16
4.9 INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD .......................... 17
4.9.1 Outline of QVGA input signal timings........................................................................................ 17
4.9.2 Outline of VGA input signal timings........................................................................................... 18
4.9.3 Detailed QVGA input signal timing chart for fixed mode .......................................................... 19
4.9.4 Detailed QVGA input signal timing chart for DE mode ............................................................. 20
4.9.5 Detailed VGA input signal timing chart for fixed mode ............................................................. 21
4.9.6 Detailed VGA input signal timing chart for DE mode ................................................................ 22
4.9.7 Timing characteristics for QVGA display mode ......................................................................... 23
4.9.8 Timing characteristics for VGA display mode ............................................................................ 24
4.10 OPTICS.............................................................................................................................................. 25
4.10.1 Optical characteristics ............................................................................................................... 25
4.10.2 Definition of contrast ratio ........................................................................................................ 26
4.10.3 Definition of luminance uniformity........................................................................................... 26
4.10.4 Definition of response times...................................................................................................... 26
4.10.5 Definition of viewing angles..................................................................................................... 26
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 4
CONTENTS
5. RELIABILITY TESTS............................................................................................................................ 27
6. PRECAUTIONS....................................................................................................................................... 28
6.1 MEANING OF CAUTION SIGNS ..................................................................................................... 28
6.2 CAUTIONS ......................................................................................................................................... 28
6.3 ATTENTIONS...................................................................................................................................... 28
6.3.1 Handling of the product............................................................................................................... 28
6.3.2 Environment ................................................................................................................................ 28
6.3.3 Characteristics............................................................................................................................. 29
6.3.4 Other............................................................................................................................................ 29
7. OUTLINE DRAWINGS .......................................................................................................................... 30
7.1 FRONT VIEW ..................................................................................................................................... 30
7.2 REAR VIEW........................................................................................................................................ 31
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 5
1. OUTLINE
1.1 STRUCTURE AND PRINCIPLE
NL3224BC35-20 module is composed of the amorphous silicon thin film transistor liquid crystal
display (a-Si TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array
and a backlight unit.
The a-Si TFT LCD panel structure is injected liquid crystal material into a narrow gap between the TFT
array glass substrate and a color-filter glass substrate.
Color (Red, Green, Blue) data signals from a host system (e.g. PC, signal generator, etc.) are modulated
into best form for active matrix system by a signal processing board, and sent to the driver LSIs which
drive the individual TFT arrays.
The TFT array as an electro-optical switch regulates the amount of transmitted light from the backlight
assembly, when it is controlled by data signals. Color images are created by regulating the amount of
transmitted light through the TFT array of red, green and blue dots.
1.2 APPLICATIONS
• Industrial PC
• Display terminal for control system
• POS (Point of sale) terminal
1.3 FEATURES
• High luminance
• Wide color gamut
• Wide viewing angle
• Low reflection
• 6-bit digital RGB signals
• Reversible-scan direction
• Edge light type
• Replaceable lamp for backlight unit (Inverter less)
• Acquisition product for UL/c-UL (File number: E170632)
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 6
2. GENERAL SPECIFICATIONS
Display area 111.4 (W) × 83.5 (H) mm
Diagonal size of display 13.9 cm (5.5 inches)
Drive system a-Si TFT active matrix
Display color 262,144 colors
At QVGA display mode
320 (H) × 240 (V) pixels
Pixel
At VGA display mode
640 (H) × 480 (V) pixels (Display area: 320 (H) × 240 (V) pixels)
Pixel arrangement RGB (Red dot, Green dot, Blue dot) vertical stripe
Dot pitch 0.1160 (W) × 0.3480 (H) mm
Pixel pitch 0.3480 (W) × 0.3480 (H) mm
Module size 134.0 (W) × 104.5 (H) × 12.5 (D) mm (typ.)
Weight 210 g (typ.)
Contrast ratio 400:1 (typ.)
Viewing angle At the contrast ratio 10:1
• Horizontal: Left side 65° (typ.), Right side 65° (typ.)
• Vertical: Up side 40° (typ.), Down side 65° (typ.)
Designed viewing direction At DPSH: normal scan and DPSV: normal scan
• Viewing direction without image reversal: up side (12 o'clock)
• Viewing direction with contrast peak: down side 5° to 10° (6 o'clock)
• Viewing angle with optimum grayscale (γ=2.2): normal axis
Polarizer surface Antiglare treatment
Polarizer pencil-hardness 3H (min.) [by JIS K5400]
Color gamut At LCD panel center
50 % (typ.) [against NTSC color space]
Response time 5 ms (typ.)
Luminance At 5.0mArms / lamp
400 cd/m2 (typ.)
Signal system 6-bit digital signals for data of RGB colors,
Dot clock (CLK), Data enable (DE),
Horizontal synchronous signal (Hsync),
Vertical synchronous signal (Vsync)
Power supply voltage LCD panel signal processing board: 3.3V or 5.0V
Backlight Edge light type: 2 cold cathode fluorescent lamps
Replaceable parts
• Lamps for backlight unit: Type No. 55LHS11
Recommended inverter (Option)
• Inverter: Type No. 55PW131
Power consumption At maximum luminance and checkered flag pattern
4.1 W (typ.)
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 7
3. BLOCK DIAGRAM
Note1: GND and GNDB (Backlight inverter ground) should be connected together in customer equipment.
Note2: The metallic frame of lamp holder is used to a transmission line for VBLC.
Host
960 lines
LCD panel
H: 320 × 3 (R,G,B)
V: 240
240 lines
LCD module (Product)
Backlight unit (Edge light type)
Backlight inverter
(Option) VBLH
VBLH
GNDB VBLC
N
ote1
VBLC
Lamp
Lamp
Metallic frame of lamp holder
Metallic frame of lamp holder
N
ote2
N
ote2
V-driver
VCC
CLK
B0 to B5
G0 to G5
R0 to R5
DPSV
DE
Vsync
Hsync
GND
100Ω
100Ω
100Ω
47Ω
100Ω
100Ω
100Ω
11kΩ
LCD panel signal processing board
Power supply
for gradation
DC/DC
converter
DPSH
11kΩ
Fuse
11kΩ
Controller
PNS
47kΩ
20kΩ
20kΩ
20kΩ
N
ote1
H-driver
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 8
4. DETAILED SPECIFICATIONS
4.1 MECHANICAL SPECIFICATIONS
Parameter Specification Unit
Module size 134.0 ± 0.5 (W) × 104.5 ± 0.5 (H) × 12.5 ± 0.5 (D) Note1 mm
Display area 111.4 (W) × 83.5 (H) Note1 mm
Weight 215 (typ.), 220 (max.) g
Note1: See "7. OUTLINE DRAWINGS".
4.2 ABSOLUTE MAXIMUM RATINGS
Parameter Symbol Rating Unit Remarks
LCD panel signal board VCC -0.3 to +6.5 V
High voltage side (Hot)
Note1 VBLH 1,500 Vrms
Power supply
voltage Lamp Low voltage side (Cold)
Note2 VBLC 42.4 Vrms
Display signals
Note3 VD -0.3 to VCC+0.3 V
Input voltage
for signals Function signals
Note4 VF -0.3 to VCC+0.3 V
Ta = 25°C
Storage temperature Tst -30 to +80 °C
Front surface TopF -10 to +70 °C
Operating temperature
Rear surface TopR -10 to +75 °C
-
≤ 95 %Ta ≤ 40°C
≤ 85 %40 < Ta ≤ 50°C
≤ 70 %50 < Ta ≤ 55°C
≤ 60 %55 < Ta ≤ 60°C
≤ 50 %60 < Ta ≤ 65°C
Relative humidity
Note5 RH
≤ 42 %65 < Ta ≤ 70°C
Absolute humidity
Note5 AH ≤ 78
Note6 g/m3Ta > 70°C
Note1: "VBLH" is the voltage value between low voltage terminal (Cold) and high voltage terminal (Hot).
Note2: "VBLC" is the voltage value between backlight inverter ground (GNDB) and low voltage
terminal (Cold).
Note3: Display signals are CLK, Hsync, Vsync, DE and DATA (R0 to R5, G0 to G5, B0 to B5).
Note4: Function signals are DPSH, DPSV and PNS.
Note5: No condensation
Note6: Ta = 70°C, RH = 42%
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 9
4.3 ELECTRICAL CHARACTERISTICS
4.3.1 Driving for LCD panel signal processing board
(Ta = 25°C)
Parameter Symbol Min. Typ. Max. Unit Remarks
3.0 3.3 3.6 V for 3V system
Power supply voltage VCC 4.755.005.25V for 5V system
- 180 Note1 250 mA VCC = 3.3V Note2
Power supply current ICC - 120 Note1 165 mA VCC = 5.0V Note2
Low VDLL 0 - 0.3Vcc V
Logic input voltage for
display signals High VDLH 0.7Vcc - Vcc V
Low VFDL 0 - 0.3Vcc V
Input voltage for DPSH or
DPSV signals High VFDH 0.7Vcc - Vcc V
Low VFPL 0 - 0.3Vcc V
Input voltage for PNS signal High VFPH 0.7Vcc - Vcc V
CMOS level
Note1: Checkered flag pattern [by EIAJ ED-2522]
Note2: At QVGA display mode (PNS: Low)
4.3.2 Working for backlight lamp
Parameter Symbol Ta Min. Typ. Max. Unit Remarks
-10°C780 - - Vrms
Starting voltage VS 25°C550 - - Vrms Note1
Power supply voltage VBLH 25°C- 350 - Vrms Note1,Note2
Power supply current IBL 25°C4.5 5.0 5.5 mArms Note2
Oscillation frequency FO 25°C39 43 47 kHz Note3
Note1: The power supply voltage cycle between lamps should be kept on a same phase. "VS" and
"VBLH" are the voltage value between low voltage side (Cold) and high voltage side (Hot).
Note2: The asymmetric ratio of working waveform for lamps (Power supply voltage peak ratio,
power supply current peak ratio and waveform space ratio) should be less than 5 % (See the
following figure.). If the waveform is asymmetric, DC (Direct current) element apply into
the lamp. In this case, a lamp lifetime may be shortened, because a distribution of a lamp
enclosure substance inclines toward one side between low voltage terminal (Cold terminal)
and high voltage terminal (Hot terminal).
Pa: Supply voltage/current peak for positive, Pb: Supply voltage/current peak for negative
Sa: Waveform space for positive part, Sb: Waveform space for negative part
Note3: In case "FO" is not the recommended value, beat noise may display on the screen, because
of interference between "FO" and "1/th". Recommended value of "FO" is as following.
th: Horizontal synchronous cycle (See "4.9.7 Timing characteristics for QVGA display
mode" or "4.9.8 Timing characteristics for VGA display mode".)
n: Natural number (1, 2, 3 ⋅⋅⋅⋅⋅⋅⋅⋅)
FO =1
4
1
th
××(2n-1)
Pa
Pb
Sa
Sb
0
Pa - Pb
Pb × 100 ≤ 5 %
Sa - Sb
Sb × 100 ≤ 5 %
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 10
4.3.3 Power supply voltage ripple
This product works, even if the ripple voltage levels are beyond the permissible values as following
the table, but there might be noise on the display image.
Parameter Power supply voltage Ripple voltage Note1
(Measure at input terminal of power supply) Unit
3.3 V ≤ 100 mVp-p
VCC
5.0 V ≤ 100 mVp-p
Note1: The permissible ripple voltage includes spike noise.
4.3.4 Fuse
Fuse
Fusing line Type Supplier Rating Fusing current
Note1
1.8 A
VCC ICP-S1.8 ROHM Co., Ltd.
50 V
4.0 A
Note1: The power supply capacity should be more than the fusing current. If the power supply
capacity is less than the fusing current, the fuse may not blow for a short time, and then
nasty smell, smoking and so on may occur.
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 11
4.4 POWER SUPPLY VOLTAGE SEQUENCE
4.4.1 Sequence for LCD panel signal processing board
Note1: In terms of voltage variation (voltage drop) while VCC rising edge is below 3.0V in
"VCC = 3.3V" or 4.75V in "VCC = 5.0V", a protection circuit may work, and then this
product may not work.
Note2: Display (CLK, Hsync, Vsync, DE, R0 to R5, G0 to G5, B0 to B5) and function (DPSH,
DPSV, PNS) signals must be Low or High-impedance, exclude the VALID period (See
above sequence diagram), in order to avoid that internal circuits is damaged.
If some of display and function signals of this product are cut while this product is
working, even if the signal input to it once again, it might not work normally. If customer
stops the display and function signals, they should be cut VCC.
4.4.2 Sequence for backlight inverter (Option)
Note1: These are display and function signals for LCD panel signal processing board.
Note2: The backlight inverter voltage (VDDB) should be inputted within the valid period of
display and function signals, in order to avoid unstable data display.
VALID period
OFF
0ms < t < 35ms 0ms < t < 35ms
ON
3.0V or 4.75V
0V
Tr < 20ms
VCC
N
ote1
Display and
function signals
Note2
Toff > 200ms
Display and
function signals
Note1
VDDB
VALID period
N
ote2
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 12
4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS
4.5.1 LCD panel signal processing board
CN1 socket (LCD module side): 08-6210-033-340-800 (Kyocera Elco Corp.)
Adaptable plug: TW-VF-33-0.035 TA-200-A4.0BB-P0.5-HBL8 (Fujikura Ltd.)
Pin No. Symbol Signal Remarks
1 GND Ground
2CLK Dot clock
3 Hsync Horizontal synchronous
4 Vsync Vertical synchronous
5 GND Ground
-
6 R0 Red data (LSB) Least significant bit
7R1 Red data
8R2 Red data
9R3 Red data
10 R4 Red data
-
11 R5 Red data (MSB) Most significant bit
12 GND Ground -
13 G0 Green data (LSB) Least significant bit
14 G1 Green data
15 G2 Green data
16 G3 Green data
17 G4 Green data
-
18 G5 Green data (MSB) Most significant bit
19 GND Ground -
20 B0 Blue data (LSB) Least significant bit
21 B1 Blue data
22 B2 Blue data
23 B3 Blue data
24 B4 Blue data
-
25 B5 Blue data (MSB) Most significant bit
26 GND Ground -
27 DE Select of DE / Fixed mode DE mode: Data enable signal, Fixed mode: Open
28 VCC Power supply
29 VCC Power supply -
30 DPSH Select of scan direction (Horizontal)
31 DPSV Select of scan direction (Vertical)
Normal scan: Low or Open, Reverse scan: High
Note1
32 PNS Select of pixel number QVGA mode: Low or Open, VGA mode: High Note1
33 GND Ground -
Note1: See "4.8 SCANNING DIRECTIONS".
CN1: Figure of socket
1 2 3 32 3331
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 13
4.5.2 Backlight lamp
CN2 plug: BHR-03VS-1 (J.S.T Mfg. Co., Ltd.)
Adaptable socket: SM03 (4.0) B-BHS-TB (J.S.T Mfg. Co., Ltd.)
Pin No. Symbol Signal Remarks
1 VBLH High voltage (Hot) Pink cable
2 NC Non connection -
3 VBLC Low voltage (Cold) White cable
CN3 plug: BHR-03VS-1 (J.S.T Mfg. Co., Ltd.)
Adaptable socket: SM03 (4.0) B-BHS-TB (J.S.T Mfg. Co., Ltd.)
Pin No. Symbol Signal Remarks
1 VBLH High voltage (Hot) Pink cable
2 NC Non connection -
3 VBLC Low voltage (Cold) White cable
4.5.3 Positions of plugs and a socket
CN2: Figure of plug
1 3
CN3: Figure of plug
1 3
CN1
33
1
CN2
Low voltage (Cold)
High voltage (Hot)
3
1
CN3 Low voltage (Cold)
High voltage (Hot)
1
3
←Insert direction
Barcode label Name plate
Caution label Disposal method label
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 14
4.6 DISPLAY COLORS AND INPUT DATA SIGNALS
This product can display in equivalent to 262,144 colors in 64 scale. Also the relation between
display colors and input data signals is as the following table.
Data signal (0: Low level, 1: High level)
Display colors R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
Basic colors
Black
Blue
Red
Magenta
Green
Cyan
Yellow
White
000000
000000
111111
111111
000000
000000
111111
111111
000000
000000
000000
000000
111111
111111
111111
111111
000000
111111
000000
111111
000000
111111
000000
111111
Red scale
Black
dark
↑
↓
bright
Red
000000
000001
000010
:
:
111101
111110
111111
000000
000000
000000
:
:
000000
000000
000000
000000
000000
000000
:
:
000000
000000
000000
Green scale
Black
dark
↑
↓
bright
Green
000000
000000
000000
:
:
000000
000000
000000
000000
000001
000010
:
:
111101
111110
111111
000000
000000
000000
:
:
000000
000000
000000
Blue scale
Black
dark
↑
↓
bright
Blue
000000
000000
000000
:
:
000000
000000
000000
000000
000000
000000
:
:
000000
000000
000000
000000
000001
000010
:
:
111101
111110
111111
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 15
4.7 DISPLAY POSITIONS
The following table is the coordinates per pixel (See figure of "4.8 SCANNING DIRECTIONS".).
C( 0, 0) C( 1, 0) • • •C( X, 0) • • •C(318, 0) C(319, 0)
C( 0, 1) C( 1, 1) • • •C( X, 1) • • •C(318, 1) C(319, 1)
•
•
•
•
•
•
•
• • •
•
•
•
•
•
• • •
•
•
•
•
•
• • •
•
C( 0, Y) C( 1, Y) • • •C( X, Y) • • •C(318, Y) C(319, Y)
•
•
•
•
•
•
•
• • •
•
•
•
•
•
• • •
•
•
•
•
•
•
•
C( 0,238) C( 1,238) • • •C( X,238) • • •C(318,238) C(319,238)
C( 0,239) C( 1,239) • • •C( X,239) • • •C(318,239) C(319,239)
4.8 SCANNING DIRECTIONS
4.8.1 QVGA display mode
The following figures are seen from a front view. Also the arrow shows the direction of scan.
Note1: Meaning of C (X, Y) and D (X, Y)
C (X, Y): The coordinates of the display position (See "4.7 DISPLAY POSITIONS".)
D (X, Y): The data number of QVGA input signal for LCD panel signal processing board
Note2: Normal scan: Low or Open, Reverse scan: High
Figure 2. DPSH: Reverse scan, DPSV: Normal scanFigure 1. DPSH: Normal scan, DPSV: Normal scan
C (0,0)
D (319,0)
C (0,239)
D (319,239)
C (319,239)
D (0,239)
C (319,0)
D (0,0)
Figure 4. DPSH: Reverse scan, DPSV: Reverse scan
Figure 3. DPSH: Normal scan, DPSV: Reverse scan
C (0,0)
D (0,0)
C (0,239)
D (0,239)
C (319,239)
D (319,239)
C (319,0)
D (319,0)
C (0,0)
D (0,239)
C (0,239)
D (0,0)
C (319,239)
D (319,0)
C (319,0)
D (319,239)
C (0,0)
D (319,239)
C (0,239)
D (319,0)
C (319,239)
D (0,0)
C (319,0)
D (0,239)
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 16
4.8.2 VGA display mode
The following figures are seen from a front view. Also the arrow shows the direction of scan, and a
dotted line is a virtual display domain. In this display mode, only quarter domains of virtual display
are displayed on the screen.
Note1: Meaning of C (X, Y) and D (X, Y)
C (X, Y): The coordinates of the display position (See "4.7 DISPLAY POSITIONS".)
D (X, Y): The data number of VGA input signal for LCD panel signal processing board
Note2: Normal scan: Low or Open, Reverse scan: High
C (0,0)
D (0,0)
D (639,0)
C (319,0)
D (0,479)
C (0,239) C (319,239)
D (639,479)
C (0,0)
D (639,0)
D (0,0)
C (319,0)
D (639,479)
C (0,239) C (319,239)
D (0,479)
C (0,0)
D (0,479)
D (639,479)
C (319,0)
D (0,0)
C (0,239) C (319,239)
D (639,0)
C (0,0)
D (639,0)
D (0,479)
C (319,0)
D (639,0)
C (0,239) C (319,239)
D (0,0)
Figure 1. DPSH: Normal scan, DPSV: Normal scan Figure 2. DPSH: Reverse scan, DPSV: Normal scan
Figure 3. DPSH: Normal scan, DPSV: Reverse scan Figure 4. DPSH: Reverse scan, DPSV: Reverse scan
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 17
4.9 INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD
4.9.1 Outline of QVGA input signal timings
• Horizontal signal
Note1: Fixed mode cannot be used while working of DE mode.
Note2: This diagram indicates virtual signal for set up to timing.
Note3: Customer should be inputted synchronized signals (Hsync, Vsync) in addition to DE
signal to this product, when it is worked in DE mode. Synchronized signals are used for
DE/Fixed mode detection.
• Vertical signal
Note1: Fixed mode cannot be used while working of DE mode.
Note2: This diagram indicates virtual signal for set up to timing.
Note3: Customer should be inputted synchronized signals (Hsync, Vsync) in addition to DE
signal to this product, when it is worked in DE mode. Synchronized signals are used for
DE/Fixed mode detection.
Note4: See "4.9.3 Detailed QVGA input signal timing chart for fixed mode" and "4.9.4 Detailed
QVGA input signal timing chart for DE mode" for numeration of pulse.
Horizontal back-porch (thb) Horizontal front-porch (thf)
Horizontal synchronizing pulse width (thp)
Horizontal synchronizing cycle (th)
Horizontal display period (thd)
Hsync
(Fixed mode)
Note1
Display period
Note2
Data enable
(DE mode)
Note3
Vertical back-porch (tvb) Vertical front-porch (tvf)
Vertical synchronizing pulse width (tvp)
Vertical synchronizing cycle (tv)
Vertical display period (tvd)
1234 240
Vsync
(Fixed mode)
Note1
Display period
Note2
Data enable
(DE mode)
Note3
N
ote4
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 18
4.9.2 Outline of VGA input signal timings
• Horizontal signal
Note1: Fixed mode cannot be used while working of DE mode.
Note2: This diagram indicates virtual signal for set up to timing.
Note3: Customer should be inputted synchronized signals (Hsync, Vsync) in addition to DE
signal to this product, when it is worked in DE mode. Synchronized signals are used for
DE/Fixed mode detection.
• Vertical signal
Note1: Fixed mode cannot be used while working of DE mode.
Note2: This diagram indicates virtual signal for set up to timing.
Note3: Customer should be inputted synchronized signals (Hsync, Vsync) in addition to DE
signal to this product, when it is worked in DE mode. Synchronized signals are used for
DE/Fixed mode detection.
Note4: See "4.9.5 Detailed VGA input signal timing chart for fixed mode" and "4.9.6 Detailed
VGA input signal timing chart for DE mode" for numeration of pulse.
Horizontal back-porch (thb) Horizontal front-porch (thf)
Horizontal synchronizing pulse width (thp)
Horizontal synchronizing cycle (th)
Horizontal display period (thd)
Hsync
(Fixed mode)
Note1
Display period
Note2
Data enable
(DE mode)
Note3
Vertical back-porch (tvb) Vertical front-porch (tvf)
Vertical synchronizing pulse width (tvp)
Vertical synchronizing cycle (tv)
Vertical display period (tvd)
1234 480
Vsync
(Fixed mode)
Note1
Display period
Note2
Data enable
(DE mode)
Note3
N
ote4
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 19
4.9.3 Detailed QVGA input signal timing chart for fixed mode
• Outline chart
Note1: X is data number from 1 to 318. See "4.8.1 QVGA display mode".
• Detail of A part
tvrf
tvrf
VDLH
VDLL
Vsync
VDLH
VDLL
Hsync
VDLH
0.5VCC
VDLL
CLK
VDLH
VDLL
DATA
(R0 to R5)
(G0 to G5)
(B0 to B5)
tvhs
tvhh
tvhs
tvhh
thrf thr
f
thh
ths ths
thh tdrf
tdrf
tds
tdh
tcr
f
tcrf
tch
tc
397 398 404
1260 61 77 78
D (0, 0) D (319, 0) D (0, 239) D (319, 239)
260
22 2621
D (X, 0) D (X, 239) Note1
261214
th
p
thp + thb thd thf
tvp
tvp + tvb tvd tvf
A
3
tvb
thb
th
tv
2
VDLH
0.5VCC
VDLL
CLK
tc
tch
thh ths
tds tdh
tdrf
tdrf
thh ths
thrf thrf
tcrf tcrf
VDLH
VDLL
DATA
(R0 to R5)
(G0 to G5)
(B0 to B5)
VDLH
VDLL
Hsync
1260 61 77 78
thp + thb
thp thb
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 20
4.9.4 Detailed QVGA input signal timing chart for DE mode
Customer should be inputted synchronized signals (See "4.9.3 Detailed QVGA input signal
timing chart for fixed mode".) in addition to DE signal to this product, when it is worked in DE
mode. Synchronized signals are used for DE/Fixed mode detection.
• Outline chart
Note1: X is data number from 1 to 318. See "4.8.1 QVGA display mode".
• Detail of A part
Note1: X is data number from 1 to 318. See "4.8.1 QVGA display mode".
DE
VDLH
0.5VCC
VDLL
CLK
VDLH
VDLL
DATA
(R0 to R5)
(G0 to G5)
(B0 to B5)
tdes
tdeh
tdrf
tdrf
tds tdh
tcrf
tcr
f
tch
tc
320
D (0, 0) D (319, 0)
240
1
D (X, 0)
thd
tvd
A
X+1
tdes
tder
f
tderf
Note11
2
D (X, 2)D (0, 2) D (319, 2)
404 (typ.)
tdeh
321
D (X, 239)D (0, 239) D (319, 239)
VDLH
0.5VCC
VDLL
tv
th
Note1
VDLH
0.5VCC
VDLL
CLK
tds tdh
tdrf
tdrf
tc
tcrf
tderf
VDLH
VDLL
DATA
(R0 to R5)
(G0 to G5)
(B0 to B5)
DE
tch
tcrf
tdeh tdes
tderf
tdeh tdes
VDLH
VDLL
D (0, 0) D (X, 0) D (319, 0)
1X+1 320 321
N
ote1
N
ote1
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 21
4.9.5 Detailed VGA input signal timing chart for fixed mode
• Outline chart
Note1: X is data number from 1 to 638. See "4.8.2 VGA display mode".
• Detail of A part
tvrf
tvrf
VDLH
VDLL
Vsync
VDLH
VDLL
Hsync
VDLH
0.5VCC
VDLL
CLK
VDLH
VDLL
DATA
(R0 to R5)
(G0 to G5)
(B0 to B5)
tvhs
tvhh
tvhs
tvhh
thrf thr
f
thh
ths ths
thh tdrf
tdrf
tds
tdh
tcr
f
tcrf
tch
tc
784 785 800
1210 11 144 145
D (0, 0) D (639, 0) D (0, 479) D (639, 479)
513
34 5251
D (X, 0) D (X, 479) Note1
514334
th
p
thp + thb thd thf
tv
p
tvp + tvb tvd tvf
A
3
tvb
thb
th
tv
2
VDLH
0.5VCC
VDLL
CLK
tc
tch
thh ths
tds tdh
tdrf
tdrf
thh ths
thrf thrf
tcrf tcrf
VDLH
VDLL
DATA
(R0 to R5)
(G0 to G5)
(B0 to B5)
VDLH
VDLL
Hsync
1210 11 144 145
thp + thb
thp thb
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 22
4.9.6 Detailed VGA input signal timing chart for DE mode
Customer should be inputted synchronized signals (See "4.9.5 Detailed VGA input signal timing
chart for fixed mode".) in addition to DE signal to this product, when it is worked in DE mode.
Synchronized signals are used for DE/Fixed mode detection.
• Outline chart
Note1: X is data number from 1 to 638. See "4.8.2 VGA display mode".
• Detail of A part
Note1: X is data number from 1 to 638. See "4.8.2 VGA display mode".
DE
VDLH
0.5VCC
VDLL
CLK
VDLH
VDLL
DATA
(R0 to R5)
(G0 to G5)
(B0 to B5)
tdes
tdeh
tdrf
tdrf
tds tdh
tcrf
tcr
f
tch
tc
640
D (0, 0) D (639, 0)
480
1
D (X, 0)
thd
tvd
A
X+1
tdes
tder
f
tderf
Note11
2
D (X, 2)D (0, 2) D (639, 2)
800 (typ.)
tdeh
641
D (X, 479)D (0, 479) D (639, 479)
VDLH
0.5VCC
VDLL
tv
th
Note1
VDLH
0.5VCC
VDLL
CLK
tds tdh
tdrf
tdrf
tc
tcrf
tderf
VDLH
VDLL
DATA
(R0 to R5)
(G0 to G5)
(B0 to B5)
DE
tch
tcrf
tdeh tdes
tderf
tdeh tdes
VDLH
VDLL
D (0, 0) D (X, 0) D (639, 0)
1X+1 640 641
N
ote1
N
ote1
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 23
4.9.7 Timing characteristics for QVGA display mode
• Common to DE mode and fixed mode
Parameter Symbol Min. Typ. Max. Unit Remarks
Frequency tcf 5.0 6.4 7.0 MHz 157.5 ns (typ.) Note1
Duty tcd 0.4 - 0.6 - Note1
CLK
Rise time, Fall time tcrf - - 10 ns
Setup time tds 5 - - ns
CLK-DATA Hold time tdh 10 - - ns
DATA
Rise time, Fall time tdrf - - 10 ns
-
Note1: Definition of parameters is as follows.
tcf = 1/tc, tcd = tch/tc = tch×tcd
• Fixed mode
Parameter Symbol Min. Typ. Max. Unit Remarks
57.7 63.5 80.8
µ
s15.7 kHz (typ.)
Cycle th 404 CLK
Display period thd 320 CLK
Front-porch thf 7 CLK
Pulse width thp 3 - 76 CLK
Back-porch thb 1 - 74 CLK
Note1
Total of pulse width and back-porch thp + thb 77 CLK Note1, Note2
Setup time ths 5 - - ns
CLK- Hsync Hold time thh 10 - - ns
Hsync
Rise time, Fall time thrf - - 10 ns
-
15.1 16.6 21.2 ms 60.1 Hz (typ.)
Cycle tv 262 H
Display period tvd 240 H
Front-porch tvf 1 H
Pulse width tvp 2 - 20 H
Back-porch tvb 1 - 19 H
Note1
Total of pulse width and back-porch tvp + tvb 21 H Note1, Note2
Setup time tvhs 1 - - CLK Note1
Vsync-Hsync Hold time tvhh 10 - - ns
Vsync
Rise time, Fall time tvrf - - 10 ns -
Note1: Definition of parameters is as follows.
tc = 1CLK, th = 1H
Note2: Keep tvp + tvb and thp + thb within the table. If it is out of specification, display position will
be shifted to right/left side or up/down.
• DE mode
Parameter Symbol Min. Typ. Max. Unit Remarks
Cycle th 331 404 - CLK
Horizontal Display period thd 320 CLK
Cycle tv 224 262 - H
Vertical
(One frame) Display period tvd 240 H
Note2
Setup time tdes 5 - - ns
CLK-DE Hold time tdeh 10 - - ns
DE
Note1
Rise time, Fall time tderf - - 10 ns
-
Note1: Customer should be inputted synchronized signals (See fixed mode in "4.9.7 Timing
characteristics for QVGA display mode".) in addition to DE signal to this product, when it is
worked in DE mode. Synchronized signals are used for DE/Fixed mode detection.
Note2: Definition of parameters is as follows.
tc = 1CLK, th = 1H
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 24
4.9.8 Timing characteristics for VGA display mode
• Common to DE mode and fixed mode
Parameter Symbol Min. Typ. Max. Unit Remarks
Frequency tcf - 25.2 - MHz 39.7 ns (typ.) Note1
Duty tcd - 0.5 - - Note1
CLK
Rise time, Fall time tcrf - - - ns
Setup time tds - - - ns
CLK-DATA Hold time tdh - - - ns
DATA
Rise time, Fall time tdrf - - - ns
-
Note1: Definition of parameters is as follows.
tcf = 1/tc, tcd = tch/tc = tch×tcd
• Fixed mode
Parameter Symbol Min. Typ. Max. Unit Remarks
- 31.8 -
µ
s31.4 kHz (typ.)
Cycle th 800 CLK
Display period thd 640 CLK
Front-porch thf 16 CLK
Pulse width thp - - - CLK
Back-porch thb - - - CLK
Note1
Total of pulse width and back-porch thp + thb 144 CLK Note1, Note2
Setup time ths - - - ns
CLK- Hsync Hold time thh - - - ns
Hsync
Rise time, Fall time thrf - - - ns
-
- 16.7 - ms 59.9 Hz (typ.)
Cycle tv 525 H
Display period tvd 480 H
Front-porch tvf 12 H
Pulse width tvp - - - H
Back-porch tvb - - - H
Note1
Total of pulse width and back-porch tvp + tvb 33 H Note1, Note2
Setup time tvhs - - - CLK Note1
Vsync-Hsync Hold time tvhh - - - ns
Vsync
Rise time, Fall time tvrf - - - ns -
Note1: Definition of parameters is as follows.
tc = 1CLK, th = 1H
Note2: Keep tvp + tvb and thp + thb within the table. If it is out of specification, display position will
be shifted to right/left side or up/down.
• DE mode
Parameter Symbol Min. Typ. Max. Unit Remarks
Cycle th - 800 - CLK
Horizontal Display period thd 640 CLK
Cycle tv - 525 - H
Vertical
(One frame) Display period tvd 480 H
Note2
Setup time tdes - - - ns
CLK-DE Hold time tdeh - - - ns
DE
Note1
Rise time, Fall time tderf - - - ns
-
Note1: Customer should be inputted synchronized signals (See fixed mode in "4.9.8 Timing
characteristics for VGA display mode".) in addition to DE signal to this product, when it is
worked in DE mode. Synchronized signals are used for DE/Fixed mode detection.
Note2: Definition of parameters is as follows.
tc = 1CLK, th = 1H
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 25
4.10 OPTICS
4.10.1 Optical characteristics
The following characteristics are only applied to QVGA display mode.
Parameter Note1 Condition Symbol Min. Typ. Max. Unit Remarks
Contrast ratio White/Black at center
θR = 0°, θL = 0°, θU= 0°, θD= 0°CR 320 400 - - Note2
Luminance White at center
θR = 0°, θL = 0°, θU= 0°, θD= 0°L 320 400 - cd/m2-
Luminance uniformity - LU - 1.25 1.35 - Note3
x coordinate Wx -0.305 - -
White
y coordinate Wy -0.330 - -
x coordinate Rx -0.600 --
Red
y coordinate Ry -0.350 --
x coordinate Gx -0.320 --
Green
y coordinate Gy -0.560 --
x coordinate Bx -0.150 --
Chromaticity
Blue
y coordinate By -0.130 --
Color gamut θR = 0°, θL = 0°, θU= 0°, θD= 0°
at center, against NTSC color space C-50 - %
Note4
White to black Ton - 5 15 ms
Response time
Black to white Toff - 25 50 ms
Note5
Note6
Right θU = 0°, θD = 0°, CR = 10 θR-65 -°
Left θU = 0°, θD = 0°, CR = 10 θL-65 -°
Up θR = 0°, θL = 0°, CR = 10 θU-40 -°
Viewing angle
Down θR = 0°, θL = 0°, CR = 10 θD-65 -°
Note7
Note1: Measurement conditions are as follows.
Ta = 25°C, VCC = 3.3V, IBL = 5.0mArms/lamp, DPSH: Low, DPSV: Low, PNS: Low
Optical characteristics are measured at luminance saturation after 20minutes from working
the product, in the dark room. Also measurement method for luminance is as follows.
Note2: See "4.10.2 Definition of contrast ratio".
Note3: See "4.10.3 Definition of luminance uniformity".
Note4: These coordinates are found on CIE 1931 chromaticity diagram.
Note5: Product surface temperature: TopF = 32.5°C
Note6: See "4.10.4 Definition of response times".
Note7: See "4.10.5 Definition of viewing angles".
1°
Photodetector (TOPCON BM-5A)
LCD module
(Product)
50cm
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 26
4.10.2 Definition of contrast ratio
The contrast ratio is calculated by using the following formula.
Luminance of white screen
Luminance of black screen
4.10.3 Definition of luminance uniformity
The luminance uniformity is calculated by using following formula.
Maximum luminance from ①
①①
① to ⑤
⑤⑤
⑤
Minimum luminance from ①
①①
① to ⑤
⑤⑤
⑤
The luminance is measured at near the 5 points shown below.
4.10.4 Definition of response times
Response time is measured, the luminance changes from "white" to "black", or "black" to "white" on
the same screen point, by photo-detector. Ton is the time it takes the luminance change from 90%
down to 10%. Also Toff is the time it takes the luminance change from 10% up to 90% (See the
following diagram.).
4.10.5 Definition of viewing angles
①
①①
①②
②②
②
③
③③
③
④
④④
④⑤
⑤⑤
⑤
80 160 210
60
120
180
Contrast ratio (CR) =
Luminance uniformity (LU) =
Left Upper
Lower
N
ormal axis (Perpendicular)
θU
θD
θR
θL12 o’clock
Right
100%
90%
10%
0%
Ton Toff
Luminance
White
Black
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 27
5. RELIABILITY TESTS
The result for reliability tests is only applied to QVGA display mode.
Test item Condition Judgement
High temperature and humidity
(Operation)
① 55 ± 2°C, RH = 85%, 240hours
② Display data is black.
High temperature
(Operation)
① 70 ± 2°C, 240hours
② Display data is black.
Heat cycle
(Operation)
① -10 ± 3°C…1hour
70 ± 3°C…1hour
② 50cycles, 4hours/cycle
③ Display data is black.
Thermal shock
(Non operation)
① -30 ± 3°C…30minutes
80 ± 3°C…30minutes
② 100cycles, 1hour/cycle
③ Temperature transition time is within 5
minutes.
ESD
(Operation)
① 150pF, 150Ω, ±10kV
② 9 places on a panel surface Note2
③ 10 times each places at 1 sec interval
Dust
(Operation)
① Sample dust: No. 15 (by JIS-Z8901)
② 15 seconds stir
③ 8 times repeat at 1 hour interval
No display malfunctions Note1
Vibration
(Non operation)
① 5 to 200Hz, 29.4m/s2
② 10 minute/cycle
③ X, Y direction…2hours
④ Z direction…4hours
Mechanical shock
(Non operation)
① 980m/ s2, 11ms
② ±X, ±Y, ±Z direction
③ 3 times each directions
No display malfunctions Note1
No physical damages
Note1: Display functions are checked under the same conditions as product inspection.
Note2: See the following figure for discharge points.
¡¡
¡
¡¡
¡
¡¡
¡
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 28
6. PRECAUTIONS
6.1 MEANING OF CAUTION SIGNS
The following caution signs have very important meaning. Be sure to read "6.2 CAUTIONS", after
understanding this contents!
This sign has the meaning that customer will be injured by himself, if customer has
wrong operations.
6.2 CAUTIONS
∗
∗∗
∗ Pay attention to burn injury for the working backlight! It may be over 35°
°°
°C from
ambient temperature.
∗
∗∗
∗ Do not shock and press the LCD panel and the backlight! Danger of breaking, because
they are made of glass. (Shock: To be not greater 980m/s2 and to be not greater 11ms,
Pressure: To be not greater 19.6N)
6.3 ATTENTIONS
6.3.1 Handling of the product
① Take hold of both ends without touch the circuit board when customer pulls out products (LCD
modules) from inner packing box. If customer touches it, products may be broken down or out of
adjustment, because of stress to mounting parts.
② Do not hook cables nor pull connection cables such as flexible cable and so on, for fear of damage.
③ If customer puts down the product temporarily, the product puts on flat subsoil as a display side
turns down.
④ Take the measures of electrostatic discharge such as earth band, ionic shower and so on, when
customer deals with the product, because products may be damaged by electrostatic.
⑤ The torque for mounting screws must never exceed 0.29N⋅m. Higher torque values might result in
distortion of the bezel.
⑥ Do not press or rub on the sensitive display surface. If customer clean on the panel surface, NEC
Corporation recommends using the cloth with ethanolic liquid such as screen cleaner for LCD.
⑦ Do not push-pull the interface connectors while the product is working, because wrong power
sequence may break down the product.
6.3.2 Environment
① Do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive
gases. Keep the product in antistatic pouch in room temperature, because of avoidance for dusts
and sunlight, if customer stores the product.
② Do not operate in high magnetic field. Circuit boards may be broken down by it.
③ Use an original protection sheet on the product surface (polarizer). Adhesive type protection sheet
should be avoided, because it may change color or properties of the polarizer.
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 29
6.3.3 Characteristics
The following items are neither defects nor failures.
① Response time, luminance and color may be changed by ambient temperature.
② The LCD may be seemed luminance non-uniformity, flicker, vertical seam or small spot by display
patterns.
③ Optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change
depending on operating time, and especially low temperature, because the LCD has cold cathode
fluorescent lamps.
④ Do not display the fixed pattern for a long time because it may cause image sticking. Use a screen
saver, if the fixed pattern is displayed on the screen.
⑤ The display color may be changed by viewing angle because of the use of condenser sheet in the
backlight unit.
⑥ Optical characteristics may be changed by input signal timings.
⑦ The interference noise of input signal frequency for this product's signal processing board and
luminance control frequency of customer's backlight inverter may appear on a display. Set up
luminance control frequency of backlight inverter so that the interference noise does not appear.
6.3.4 Other
① All GND, backlight inverter ground (GNDB), VCC and backlight inverter power supply voltage
(VDDB) terminals should be used without a non-connected line.
② Do not disassemble a product or adjust volume without permission of NEC Corporation.
③ See "REPLACEMENT MANUAL FOR LAMPHOLDER", if customer would like to replace
backlight lamps.
④ Pay attention not to insert waste materials inside of products, if customer uses screwnails.
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 30
7. OUTLINE DRAWINGS
7.1 FRONT VIEW
Unit: mm
(BEZEL OPEN ING AREA )
116 .4
+0 .5
-0 .5
(ACT IVE AREA )
104 .5
+0 .5
-0 .5
DISPLAY CENTER
134 .0
+0 .5
-0 .5
(ACT IVE AREA )
88 .5
+0 .5
-0 .5
(BEZE L OPEN ING AREA )
12 .5
+0 .5
-0 .5
100 .0
+5 .0
-5 .0
LOW ER S ID E
UPPER S IDE
111 .4
83 .5
NL3224BC35-20
DATA SHEET EN0556EJ3V0DS00 31
7.2 REAR VIEW
Unit: mm
12 .5
+0 .5
-0 .5
12 .5
+0 .5
-0 .5
12 .5
+0 .5
-0 .5
4.1
+0 .5
-0 .5
4.1
+0 .5
-0 .5
125 .8
+0 .3
-0 .3
HIGH VOLTAGE
RISK 0F ELECTRIC SHOCK.
POWER BEFORE SERV ICE .
D ISCONNECT THE ELECTR IC
CAUT ION
TH E T F T CO LO R LC D
PANEL CONTA INS CO LD CATHODE
FLOURESCENT LAMPS . PLEASE
FO L LOW LOC A L O RD IN AN CE S
OR REGU LA T IONS FOR I TS
DISPOSAL
**************
*******************
****************
********
60 .0
+0 .3
-0 .3
30 .0
+0 .5
-0 .5
22 .3
+0 .5
-0 .5
************
CN 1
100 .0
+5 .0
-5 .0
CN 2
CN 3
MOUN T ING SCR EW (M 3 )
Dep th 3 .0mm
E170632
**.**.**/
*************
********
PANE L :
SER IA L :
MODE L :
MADE IN JAPAN
CUS
NL3224BC35 -20
R
