Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series ZA Varistor Series RoHS Description The ZA Series of transient voltage surge suppressors are radial leaded varistors (MOVs) designed for use in the protection of low and medium-voltage circuits and systems. Typical applications include motor control, telecom, solenoid, and power supply circuits to protect circuit board components and maintain data integrity. These devices are available in five model sizes: 5mm, 7mm, 10mm, 14mm and 20mm, and feature a wide VDC voltage range of 5.5V to 615V. See ZA Series Device Ratings and Specifications Table for part number and brand information. Agency Approvals Agency Agency Approval Agency File Number UL1449* E320116 CECC 42201-006 IEC 61051-1 IEC 61051-2 IEC 60950-1 (Annex Q)** 116895 CECC 42201-006 IEC 61051-1 IEC 61051-2 IEC 60950-1 (Annex Q)** E1273/F Notes: * - Except parts V8ZAxxP and V12ZAxxP. ** - For 14mm (V120 to V180) and 20mm (V120 to V180). Features * Lead-free, HalogenFree and RoHS compliant * 5 model sizes available: 5, 7, 10, 14, and 20mm * Wide operating voltage range VM(AC)RMS 4V to 460V * Radial lead package for hard-wired or printed circuit board designs * DC voltage ratings 5.5V to 615V * Available in tape and reel or bulk pack * No derating up to 85C ambient * Standard lead form options Additional Information Datasheet Resources Samples Absolute Maximum Ratings * For ratings of individual members of a series, see Device Ratings and Specifications chart Continuous ZA Series Units Steady State Applied Voltage: AC Voltage Range (VM(AC)RMS) DC Voltage Range (VM(DC)) 4 to 460 V 5.5 to 615 V 50 to 6500 A Transients: Peak Pulse Current (ITM) For 8/20s Current Wave (See Figure 2) Single Pulse Energy Range (Note 1) 0.1 to 52 J Operating Ambient Temperature Range (TA) For 10/1000s Current Wave (WTM) -55 to +85 C Storage Temperature Range (TSTG) -55 to +125 C Temperature Coefficient (aV) of Clamping Voltage (VC) at Specified Test Current <0.01 %/C Hi-Pot Encapsulation (COATING Isolation Voltage Capability) (Dielectric must withstand indicated DC voltage for one minute per MIL-STD-202, Method 301) 2500 V COATING Insulation Resistance 1000 M CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series ZA Series Ratings & Specifications Part Number Branding Maximum Rating (85C) Specifications (25C) Continuous Transient Maximum Varistor Voltage at Clamping Peak 1mA Energy 10 Voltage VDC Current VRMS Model Size DC Test Current x 1000s 8 x 20s 8 x 20s Disc Dia. (mm) VNOM VNOM VM(DC) WTM ITM IPK VC VM(AC) Min Max (V) (V) (J) (A) (V) (V) (V) (A) 5 4 5.5 0.1 50 6 11 30 1 7 4 5.5 0.4 100 6 11 22 2.5 10 4 5.5 0.8 250 6 11 20 5 5 6 8 0.14 50 9 16 37 1 7 6 8 0.6 100 9 16 34 2.5 10 6 8 1.2 250 9 16 30 5 5 10 14 0.17 100 16.2 19.8 36 1 7 10 14 0.8 250 16.2 19.8 36 2.5 10 10 14 1.5 500 16.2 19.8 36 5 14 10 14 3.5 1000 16.2 19.8 36 10 20 10 14 10 2000 16.2 19.8 37 20 16.2 80 2000 19.8 37 20 20 10 14 V8ZA05P V8ZA1P V8ZA2P V12ZA05P V12ZA1P V12ZA2P V18ZA05P V18ZA1P V18ZA2P V18ZA3P V18ZA20P PZ08 P08Z1 P08Z2 PZ12 P12Z1 P12Z2 PZ18 P18Z1 P18Z2 P18Z3 P18Z20 V18ZA40P P18Z40 V22ZA05P V22ZA1P V22ZA2P V22ZA3P V24ZA20P PZ22 P22Z1 P22Z2 P22Z3 P24Z20 5 7 10 14 20 14 14 14 14 14 V24ZA50P P24Z50 20 14 V27ZA05P V27ZA1P V27ZA2P V27ZA4P V27ZA20P PZ27 P27Z1 P27Z2 P27Z4 P27Z20 5 7 10 14 20 V27ZA60P P27Z60 V33ZA05P V33ZA1P V33ZA2P V33ZA5P V33ZA20P 18 18 18 18 18 18 0.2 0.9 2 4 12 100 (Note 4) (Note 2) 17 17 17 17 17 22 22 22 22 22 20 17 PZ33 P33Z1 P33Z2 P33Z5 P33Z20 5 7 10 14 20 V33ZA70P P33Z70 V36ZA20P P36Z20 C (pF) 2000 4190 7000 1700 3350 6100 1400 2700 5300 18870 22000 22000 100 250 500 1000 2000 19.8 19.8 19.8 19.8 19.8 24.2 24.2 24.2 24.2 24.2 43 43 43 43 43 1 2.5 5 10 20 1220 2375 4500 14730 18000 2000 20.7 (Note 3) 25.3 43 20 18000 0.25 1 2.5 5 14 100 250 500 1000 2000 24.3 24.3 24.3 24.3 24.3 29.7 29.7 29.7 29.7 29.7 53 53 53 53 53 1 2.5 5 10 20 920 1875 3850 11480 13000 22 100 (Note 2) 2000 24.3 (Note 3) 29.7 50 20 13000 20 20 20 20 20 26 26 26 26 26 100 250 500 1000 2000 29.7 29.7 29.7 29.7 29.7 36.3 36.3 36.3 36.3 36.3 65 65 65 65 65 1 2.5 5 10 20 790 1620 3495 9290 13000 20 21 27 0.3 1.2 3 6 18 100 2000 29.7 (Note 3) 36.3 58 20 13000 20 23 28 2000 32.4 39.6 70 20 12000 2000 32.4 (Note 3) 39.6 63 20 12000 100 250 500 1000 2000 100 250 500 1000 35.1 35.1 35.1 35.1 35.1 42.3 42.3 42.3 42.3 42.9 42.9 42.9 42.9 42.9 51.7 51.7 51.7 51.7 79 79 76 76 76 93 93 93 93 1 2.5 5 10 20 1 2.5 5 10 675 1350 3100 7000 12000 585 1245 2590 6270 2000 42.3 51.7 93 20 11000 (Note 2) 20 100 V36ZA80P P36Z80 20 23 28 V39ZA05P V39ZA1P V39ZA3P V39ZA6P V39ZA20P V47ZA05P V47ZA1P V47ZA3P V47ZA7P PZ39 P39Z1 P39Z3 P39Z6 P39Z20 PZ47 P47Z1 P47Z3 P47Z7 5 7 10 14 20 5 7 10 14 25 25 25 25 25 30 30 30 30 V47ZA20P P47Z20 20 30 31 31 31 31 31 38 38 38 38 38 0.3 1.2 3 7.2 20 0.4 1.8 4.5 8.8 23 (Note 6) (Note 7) (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 (Note 3) (Note2) Typical Capacitance f = 1MHz (Note 2) Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series ZA Series Ratings & Specifications (Continued...) Part Number V56ZA05P V56ZA2P V56ZA3P V56ZA8P V56ZA20P V68ZA05P V68ZA2P V68ZA3P V68ZA10P V68ZA20P V82ZA05P V82ZA2P V82ZA4P V82ZA12P V82ZA20P V100ZA05P V100ZA3P V100ZA4P V100ZA15P V100ZA20P V120ZA05P V120ZA1P V120ZA4P V120ZA6P V120ZA20P V150ZA05P V150ZA1P V150ZA4P V150ZA8P V150ZA20P V180ZA05P V180ZA1P V180ZA5P V180ZA10P V180ZA20P V205ZA05P V220ZA05P V240ZA05P V270ZA05P V330ZA05P V360ZA05P V390ZA05P V430ZA05P V470ZA05P V620ZA05P V680ZA05P V715ZA05P V750ZA05P Branding PZ56 P56Z2 P56Z3 P56Z8 P56Z20 PZ68 P68Z2 P68Z3 P68Z10 P68Z20 PZ82 P82Z2 P82Z4 P82Z12 P82Z20 PZ100 P100Z P100Z4 P100Z15 P100Z20 PZ120 P120Z P120Z4 P120Z6 P120Z20 PZ150 PZ051 P150Z4 P150Z8 P150Z20 PZ180 P180Z P180Z5 P180Z10 P180Z20 PZ205 PZ220 PZ240 PZ270 PZ330 PZ360 PZ390 PZ430 PZ470 PZ620 PZ680 PZ715 PZ750 Maximum Rating (85C) Specifications (25C) Continuous Transient Maximum Varistor Voltage at Clamping Peak 1mA Energy 10 Voltage VDC Current VRMS Model Size DC Test Current x 1000s 8 x 20s 8 x 20s Disc Dia. (mm) VNOM VNOM VM(DC) WTM ITM IPK VC VM(AC) Min Max (V) (V) (J) (A) (V) (V) (V) (A) 5 35 45 0.5 100 50.4 61.6 110 1 7 35 45 2.3 250 50.4 61.6 110 2.5 10 35 45 5.5 500 50.4 61.6 110 5 14 35 45 10 1000 50.4 61.6 110 10 20 35 45 30 2000 50.4 61.6 110 20 5 40 56 0.6 100 61.2 74.8 135 1 7 40 56 3 250 61.2 74.8 135 2.5 10 40 56 6.5 500 61.2 74.8 135 5 14 40 56 13 1000 61.2 74.8 135 10 20 40 56 33 2000 61.2 74.8 135 20 5 50 68 2 400 73.8 90.2 135 5 7 50 68 4 1200 73.8 90.2 135 10 10 50 68 8 2500 73.8 90.2 135 25 14 50 68 15 4500 73.8 90.2 145 50 20 50 68 25 6500 73.8 90.2 145 100 5 60 81 2.5 400 90 110 165 5 7 60 81 5 1200 90 110 165 10 10 60 81 10 2500 90 110 165 25 14 60 81 20 4500 90 110 175 50 20 60 81 30 6500 90 110 175 100 5 75 102 3 400 108 132 205 5 7 75 102 6 1200 108 132 205 10 10 75 102 12 2500 108 132 200 25 14 75 102 22 4500 108 132 210 50 20 75 102 33 6500 108 132 210 100 5 92 127 4 400 135 165 250 5 7 95 127 8 1200 135 165 250 10 95 127 15 2500 135 165 250 25 10 14 95 127 20 4500 135 165 250 50 20 95 127 45 6500 135 165 250 100 5 110 153 5 400 162 198 295 5 7 115 153 10 1200 162 198 300 10 10 115 153 18 2500 162 198 300 25 14 115 153 35 4500 162 198 300 50 20 115 153 52 6500 162 198 300 100 5 130 170 5.5 400 184.5 225.5 340 5 5 140 180 6 400 198 242 360 5 5 150 200 7 400 216 264 395 5 5 175 225 7.5 400 243 297 455 5 5 210 275 9 400 306 374 540 5 5 230 300 9.5 400 324 396 595 5 5 250 330 10 400 351 429 650 5 5 275 369 11 400 387 473 710 5 5 300 385 12 400 423 517 775 5 5 385 505 13 400 558 682 1025 5 5 420 560 14 400 612 748 1120 5 5 440 585 15.5 400 643.5 786.5 1180 5 5 460 615 17 400 675 825 1240 5 Note: 1. Average power dissipation of transients not to exceed 0.2W, 0.25W, 0.4W, 0.6W or 1W for model sizes 5mm, 7mm, 10mm, 14mm and 20mm, respectively. 2. Energy rating (auto load dump) for impulse duration of 40ms minimum to one half of peak current, 60 sec interval (ISO7637-2 pulse 5a and ISO16750-2 Table 5A) 3. 10mA DC test current. 4. Also rated to withstand 24V for 5 minutes. Typical Capacitance f = 1MHz C (pF) 500 1035 2150 4840 10000 400 910 1850 3870 9000 355 700 1485 3380 7000 310 600 1200 2900 6500 250 515 1100 2450 5000 190 460 860 1910 3500 100 320 465 1190 2400 100 95 90 75 70 60 80 75 70 45 40 35 30 5. Higher voltages available, contact Littelfuse. 6. Also rated to withstand 48V for 5 minutes. 7. Energy rating for impulse duration of 30ms minimum to one half of peak current (Auto Load Dump): 100J 8. The typical capacitance rating is the discrete component test result. Also Recognized to UL 1449, Transient Voltage Surge Suppressors File E320116 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series Phenolic Coating Option -- ZA Series Varistors for HiTemperature Operating Conditions: * Phenolic coated ZA Series devices are available with improved maximum operating temperature of 125C * These devices also have improved temperature cycling performance capability * Ratings and specifications are as per standard ZA Series except Hi-Pot Encapsulation (Isolation Voltage Capability) = 500V * To order: add 'X1347' to part number (e.g. V22ZA3PX1347) * These devices are not UL, VDE or CECC certified * Contact factory for further details * Product marking: LF 9 P22P3 Lead-Free, YYWW Halogen-Free & RoHS Compliant Indicator Copper Electrode Option: * Add 'W' to the end of the part number (e.g. V240ZA05PW) * Copper electrode option is only available for V240~V750 for ZA series. * Product marking: LF 9 PZ240W YYWW Lead-Free, Halogen-Free & RoHS Compliant Indicator Copper Electrode Option Identifier Phenolic Coated Option Identifier Current Energy and Power Dissipation Ratings device. The operating values of a MOV need to be derated at high temperatures as shown above. Because varistors only dissipate a relatively small amount of average power they are not suitable for repetitive applications that involve substantial amounts of average power dissipation. Should transients occur in rapid succession, the average power dissipation is the energy (watt-seconds) per pulse times the number of pulses per second. The power so developed must be within the specifications shown on the Device Ratings and Specifications Table for the specific Figure 1B - Power Derating for Phenolic Coated 100 100 90 90 PERCENT OF RATED VALUE PERCENT OF RATED VALUE Figure 1A - Power Derating for Epoxy Coated 80 70 60 50 40 30 20 80 70 60 50 40 30 20 10 10 0 -55 50 60 70 80 90 100 110 120 AMBIENT TEMPERATURE ( oC) 130 0 -55 140 150 70 80 90 100 110 100 01 = Virtual Origin of Wave T = Time from 10% to 90% of Peak T1 = Rise Time = 1.25 x T T2 = Decay Time Example - For an 8/20 s Current Waveform: 8s = T1 = Rise Time 20s = T2 = Decay Time 90 50 10 O1 T T1 TIME T2 O = Virtual Origin of Wave 1 (c) 2018 Littelfuse, Inc. T =without Timenotice. From 10% to 90% Specifications are subject to change Revised: 12/12/18 T1 = Virtual Front time = 1.25 120 130 140 150 FIGURE 1. CURRENT, ENERGY AND POWER DERATING CURVE FIGURE 1. CURRENT, ENERGY AND POWER DERATING PERCENT OF PEAK VALUE 60 AMBIENT TEMPERATURE ( oC) Peak Pulse Current CURVETest Waveform Figure 2 50 of Peak *t T2 = Virtual Time to Half Value (Impulse Duration) Example: For an 8/20s Current Waveform: Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series Maximum Clamping Voltage for 5mm Parts V8ZA05(P) - V68ZA05(P) V82ZA05(P) - V33ZA05(P) 2000 MAX CLAMPING VOLTAGE MODEL SIZE 5mm 8 TO 68VN(DC) RATING TA = -55oC TO 85oC MAXIMUM PEAK VOLTS (V) MAXIMUM PEAK VOLTS (V) 600 500 400 300 200 100 90 80 70 60 50 40 V68ZA05(P) V56ZA05(P) V47ZA05(P) V39ZA05(P) V33ZA05(P) V27ZA05(P) 30 V22ZA05(P) V18ZA05(P) 20 V12ZA05(P) MAX CLAMPING VOLTAGE MODEL SIZE 5mm 82 TO 330VN(DC) RATING TA = -55oC TO 85oC V330ZA05(P) V270ZA05(P) V240ZA05(P) V220ZA05(P) V205ZA05(P) V180ZA05(P) V150ZA05(P) V120ZA05(P) 1000 500 ) 5(P A0 0Z ) 0 (P V1 05 ZA 2 V8 200 V8ZA05(P) 10 -1 10 0 10 1 PEAK AMPERES (A) 10 2 10 3 Figure 4 FIGURE 3. CLAMPING VOLTAGE FOR V8ZA05(P) - V68ZA05(P) Figure 5 0.001 0.01 0.1 1 PEAK AMPERES (A) 10 100 FIGURE 5. CLAMPING VOLTAGE FOR V360ZA05(P) - V750ZA05(P) MAXIMUM CLAMPING VOLTAGE 100 1000 300 1,000 900 200 800 V180ZA1(P) 700 V150ZA1(P) 600 V120ZA1(P) 500 100 V100ZA3(P) 400 90 80 V68ZA2(P) V82ZA2(P) 300 70 V56ZA2(P) 60 V47ZA1(P) 50 V39ZA1(P) 200 40 V33ZA1(P) V27ZA1(P) 30 V22ZA1(P) 100 V18ZA1(P) 20-3V12ZA1(P) 10 10 -1 10 0 10 1 10 2 10 3 10 4 10 -2 PEAK AMPERES (A) V8ZA1(P) 10 FIGURE 7. CLAMPING VOLTAGE FOR V82ZA2(P) - V180ZA1(P) -3 10 10 -2 10 -1 10 0 10 1 10 2 10 3 PEAK AMPERES (A) MAXIMUM PEAK VOLTS (V) MAXIMUM PEAK VOLTS (V) MAXIMUM PEAK VOLTS (V) AGE Figure 7 600 500 400 FIGURE 6. CLAMPING VOLTAGE FOR V8ZA1(P) - V68ZA2(P) MAXIMUM CLAMPING VOLTAGE 300 1,000 200 900 800 V180ZA5(P) 700 V150ZA4(P) 600 V120ZA4(P) 500 100 V100ZA4(P) 90 400 80 V68ZA3(P) V82ZA4(P) 70 V56ZA3(P) 300 60 V47ZA3(P) 50 300 AXIMUM PEAK VOLTS (V) MAXIMUM PEAK VOLTS (V) M PEAK VOLTS (V) 500 2,000 400 MODEL SIZE 10mm 82 TO 180VN(DC) RATING TA = -55oC TO 85oC MAXIMUM CLAMPING VOLTAGE MODEL SIZE 10mm 8 TO 68VN(DC) RATING TA = -55oC TO 85oC V750ZA05(P) V715ZA05(P) V680ZA05(P) V620ZA05(P) V470ZA05(P) V430ZA05(P) V390ZA05(P) V360ZA05(P) 10 -1 10 0 10 1 PEAK AMPERES (A) 0.001 500 400 300 10 2 10 3 0.01 0.1 1 PEAK AMPERES (A) 10 100 200 100 90 80 70 60 50 10 10 10 10 PEAK AMPERES (A) 10 10 3 500 400 300 MAXIMUM CL MODEL SIZE 1 8 TO 68VN(DC TA = -55oC TO 200 100 90 80 70 60 50 40 V68ZA3(P) V56ZA3(P) V47ZA3(P) V39ZA3(P) V33ZA2(P) V27ZA2(P) 30 V22ZA2(P) V18ZA2(P) 20 V12ZA2(P) V8ZA2(P) 10 -3 10 10 -2 MAXIMUM CLAMPING VOLTAGE FIGURE 7. CLAMPING VOLTAGE FOR V82ZA2(P) - V180ZA1(P) MODEL SIZE 14mm 18 TO 68VN(DC) RATING TA = -55oC TO 85oC 4,000 MAXIMUM CLAMPING VOLTAGE MODEL SIZE 10mm 3,000 82 TO 180VN(DC) RATING TA = -55oC TO 85oC 2,000 V68ZA10(P) 1,000 900 V56ZA8(P) 800 V47ZA7(P) 700 V39ZA6(P) 600 100 90 80 V68ZA2(P) 70 V56ZA2(P) 60 V47ZA1(P) 50 V39ZA1(P) 40 V33ZA1(P) V27ZA1(P) 30 V22ZA1(P) V18ZA1(P) 20 V12ZA1(P) FIGURE 6. CLAM 10 4 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 V180ZA5(P) V150ZA4(P) V120ZA4(P) 200 MAXIMUM CL MODEL SIZE 7 8 TO 68VN(DC) TA = -55oC TO V8ZA1(P) 10 10 -3 10 -2 1000 500 MAXIMUM CLAMPING VOLTAGE 400 MODEL SIZE 5. 10mm V82ZA2(P) - V180ZA1(P) FIGURE CLAMPING VOLTAGE FOR V360ZA05(P) - V750ZA05(P) 8 TO 68VN(DC) RATING 300 TA = -55oC TO 85oC 4,000 200 MAXIMUM CLAMPING VOLTAGE MODEL SIZE 7mm 3,000 82 TO 180VN(DC) RATING TA = -55oC TO 85oC 2,000 100 90 80 V68ZA3(P) 70 V56ZA3(P) 60 V47ZA3(P) 1,000 50 V39ZA3(P) 900 40 V33ZA2(P) 800 V180ZA1(P) V27ZA2(P) 700 30 V22ZA2(P) V150ZA1(P) 600 V18ZA2(P) V120ZA1(P) 500 V100ZA3(P) 20 400 V12ZA2(P) V82ZA2(P) 300 V8ZA2(P) 10 200 10 -3 10 -2 10 -1 10 0 10 1 10 2 10 3 PEAK AMPERES (A) 10 4,000 3,000 1000 MAX CLAMPING VOLTAGE MODEL SIZE 5mm 360 TO 750VN(DC) RATING TA = -55oC TO 85oC FIGURE 8.100 CLAMPING VOLTAGE FOR V8ZA2(P) - V68ZA3(P) -3 -2 -1 0 1 2 Figure 6 - V750ZA05(P) 100 2000 90 80 V68ZA2(P) 70 V56ZA2(P) 60 V47ZA1(P) 50 V39ZA1(P) 40 V33ZA1(P) V27ZA1(P) 30 V22ZA1(P) 1000 V18ZA1(P) 20 V12ZA1(P) 0.0001 MODEL SIZE 7mm V8ZA1(P)3,000 - V68ZA2(P) ING 100 FIGURE 6. CLAMPING VOLTAGE FOR V8ZA1(P) - V68ZA2(P) Maximum Clamping Voltage for 7mm Parts 4,000 2,000 500 400 200 V8ZA1(P) 10 -3 10 10 -2 500 1000 82 TO 180VN(DC) RATING TA = -55oC TO 85oC MAXIMUM CLAMPING VOLTAGE MODEL SIZE 7mm 8 TO 68VN(DC) RATING TA = -55oC TO 85oC 0.1 1 10 PEAK AMPERES (A) MAXIMUM CLAMPING VOLTAGE MODEL SIZE 7mm 8 TO 68VN(DC) RATING TA = -55oC TO 85oC 3000 MAXIMUM PEAK VOLTS (V) 500 0.0001 0.01 MAXIMUM PEAK VOLTS (V) V750ZA05(P) V715ZA05(P) V680ZA05(P) V620ZA05(P) V470ZA05(P) V430ZA05(P) V390ZA05(P) V360ZA05(P) 300 PEAK VOLTS (V) 1000 500 400 MAX CLAMPING VOLTAGE MODEL SIZE 5mm 360 TO 750VN(DC) RATING TA = -55oC TO 85oC MAXIMUM PEAK VOLTS (V) MAXIMUM PEAK VOLTS (V) 2000 0.001 FIGURE 4. CLAMPING VOLTAGE FOR V82ZA05(P) - V33ZA05(P) V360ZA05(P) - V750ZA05(P) 3000 100 0.0001 MAXIMUM PEAK VOLTS (V) 10 -2 MAXIMUM PEAK VOLTS (V) Figure 3 FIGURE 8. CLAM 600 500 400 300 EAK VOLTS (V) 10 10 -3 200 100 MAXIMUM C MODEL SIZE 18 TO 68VN(D TA = -55oC TO PEAK MAXIMUMMAXIMUM PEAK VOLTS (V) VOLTS (V) V8ZA2(P) V82ZA2(P) - V180ZA1(P) 10 3 100 10 -3 10 -2 10 -1 10 0 10 1 PEAK AMPERES (A) 10 2 10 -2 10 -1 10 0 10 1 PEAK AMPERES (A) 10 2 10 3 V68 V56 V47 V39 V33 V27 30 V22 V18 20 V12 V8 10 10 -3 10 4 FIGURE 7. CLAMPING VOLTAGE FOR V82ZA2(P) - V180ZA1(P) FIGUR V82ZA4(P) - V180ZA5(P) 4,000 600 500 400 MAXIMUM CLAMPING VOLTAGE MODEL SIZE 10mm 82 TO 180VN(DC) RATING TA = -55oC TO 85oC 3,000 2,000 1,000 900 800 700 600 500 400 300 V180ZA5(P) V150ZA4(P) V120ZA4(P) V100ZA4(P) V82ZA4(P) 300 200 100 10 -3 Figure 9 10 -2 10 -1 10 0 10 1 PEAK AMPERES (A) 10 2 10 3 200 100 90 80 70 60 50 40 V68 V56 V47 V39 V33 V27 30 V22 V18 20 10 -3 10 4 FIGURE 9. CLAMPING VOLTAGE FOR V82ZA4(P) - V180ZA5(P) 10 3 FIGURE 10 2 10 3 10 4 V82ZA4(P) - V180ZA5(P) Transient V-I Characteristic Curves (Continued) 4,000 1,000 900 800 700 600 500 400 200 MAXIMUM PEAK VOLTS (V) 2,000 MAXIMUM PEAK VOLTS (V) 300 MAXIMUM CLAMPING VOLTAGE MODEL SIZE 14mm 82 TO 180VN(DC) RATING TA = -55oC TO 85oC 3,000 V180ZA10(P) V150ZA8(P) V120ZA6(P) V100ZA15(P) V82ZA12(P) 300 200 100 90 80 70 60 V 50 40 30 100 10 -3 Figure 11 10 -2 10 -1 10 0 10 1 10 2 PEAK AMPERES (A) 10 3 20 10 -3 10 4 FIGURE 11. CLAMPING VOLTAGE FOR V82ZA12(P) - V180ZA10(P) FIGURE FIGURE 10. CLAMPING VOLTAGE FOR V18ZA3(P) - V68ZA10(P) 1,000 MAXIMUM CLAMPING VOLTAGE MODEL SIZE 20mm 39 TO 180VM(AC) RATING 500 TA = -55oC TO 85oC V180ZA20 V150ZA20 V120ZA20 V100ZA2 300 200 100 V82ZA20(P) 50 30 10 -3 10 -2 10 -1 10 0 10 1 PEAK AMPERES (A) 10 2 FIGURE 13. CLAMPING VOLTAGE FOR V39ZA Pulse Rating Curves 50 20 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 10 5 2 10 10 2 10 3 2 100 MODEL SIZE 5mm V8ZA05(P) 1 10 4 5 10 6 10 2 50 URRENT (A) 10 4 100 200 90 80 V68ZA10(P) 70 V56ZA8(P) 60 V47ZA7(P) 50 V39ZA6(P) 100 90 V33ZA5(P) 40 80 V68ZA10(P) 70 V27ZA4(P) V56ZA8(P) 30 60 V22ZA3(P) V47ZA7(P) 50 V18ZA3(P) V39ZA6(P) 20 40 V33ZA5(P) -3 10V27ZA4(P) 10 -2 10 -1 10 0 10 1 10 2 10 3 PEAK AMPERES (A) 30 V22ZA3(P) V18ZA3(P) FIGURE 10. CLAMPING VOLTAGE FOR V18ZA3(P) - V68ZA10(P) 20 10 -3 10 -2 10 -1 10 0 10 1 10 2 10 3 PEAK AMPERES (A) Figure 10 V82ZA12(P) - V180ZA10(P) MAXIMUM PEAKVOLTS (V) 10 3 600 MAXIMUM CLAMPING VOLTAGE FIGURE 8. CLAMPING VOLTAGE FOR V8ZA2(P) - V68ZA3(P) 500 18 TO 68VN(DC) RATING o o TA = -55 C TO 85 C 300 600 MAXIMUM CLAMPING VOLTAGE 500 MODEL SIZE 14mm 200 400 18 TO 68VN(DC) RATING TA = -55oC TO 85oC 300 MODEL SIZE 14mm V18ZA3(P)400 - V68ZA10(P) URRENT (A) 10 2 V82ZA4(P) - V180ZA5(P) A) 200 100 90 80 70 60 50 40 Maximum Clamping Voltage for 14mm Parts V82ZA2(P) - V180ZA1(P) A) 10 -3 V180ZA1(P) V150ZA1(P) V120ZA1(P) V100ZA3(P) V82ZA2(P) 300 FIGURE 8. CLAMPING VOLTAGE FOR V8ZA2(P) - V68ZA3(P) 10 10 4 PEAK MAXIMUMMAXIMUM PEAK VOLTS (V) VOLTS (V) A) 10 2 MAXIMUM PEAK VOLTS Radial Lead Varistors > ZA Series 1,000 900 800 700 600 500 400 MAXIMUM PEAK VOLTS (V) Metal-Oxide Varistors (MOVs) MAXIMUM PEAK VOLTS PEAK MAXIMUMMAXIMUM PEAK VOLTS (V) VOLTS MAXIMUM CLAMPING VOLTAGE MODEL SIZE 7mm 8 TO 68VN(DC) RATING 300 TA = -55oC TO 85oC 100 90 200 80 V68ZA2(P) 70 V56ZA2(P) 60 V47ZA1(P) 50 100 V39ZA1(P) 40 90 V33ZA1(P) V68ZA2(P) 80 V27ZA1(P) 30 70 V22ZA1(P) V56ZA2(P) 60 V18ZA1(P) V47ZA1(P) 50 V12ZA1(P) 20 V39ZA1(P) 40 V33ZA1(P) V27ZA1(P) 30 V22ZA1(P) V8ZA1(P) 10 V18ZA1(P) 10 100 1000 20 10 -3 10 -2 10 -1 10 0 10 1 10 2 10 3 V12ZA1(P) A) PEAK AMPERES (A) Maximum Clamping Voltage for 10mm Parts V8ZA1(P) 10 60ZA05(P) - V750ZA05(P)V8ZA2(P) -FIGURE 6. CLAMPING VOLTAGE0 FOR V8ZA1(P) - V68ZA2(P) V68ZA3(P) -3 10 100 1000 10 10 -2 10 -1 10 10 1 10 2 10 3 A) PEAK AMPERES (A) 500 MAXIMUM CLAMPING VOLTAGE 400 MODEL SIZE 10mm VOLTAGE FOR V8ZA1(P) - V68ZA2(P) 60ZA05(P) - V750ZA05(P) FIGURE 6. CLAMPING 8 TO 68VN(DC) RATING 300 TA = -55oC TO 85oC 500 200 MAXIMUM CLAMPING VOLTAGE 400 MODEL SIZE 10mm 8 TO 68VN(DC) RATING 300 TA = -55oC TO 85oC 100 90 200 V68ZA3(P) 80 70 V56ZA3(P) 60 V47ZA3(P) 50 V39ZA3(P) 100 V33ZA2(P) 40 90 V68ZA3(P) 80 V27ZA2(P) 30 70 V22ZA2(P) V56ZA3(P) 60 V18ZA2(P) V47ZA3(P) 50 V39ZA3(P) 20 V33ZA2(P) 40 V12ZA2(P) V27ZA2(P) 30 V22ZA2(P) V8ZA2(P) 10 V18ZA2(P) -3 10 2 10 3 10 4 20 10 10 -2 10 -1 10 0 10 1 10 2 10 3 V12ZA2(P) A) PEAK AMPERES (A) Figure 8 400 MAXIMUM PEAK VOLTS (V) MPING VOLTAGE ZE 5mm VN(DC) RATING TO 85oC 20 10 10 10 1,000 900 800 700 V180ZA10(P) V180ZA10(P) 600 V150ZA8(P) V150ZA8(P) 500 V120ZA6(P) V120ZA6(P) 400 V100ZA15(P) V100ZA15(P) V82ZA12(P) V82ZA12(P) 300 V27ZA60(P) V27ZA60(P) V27ZA60(P) V27ZA60(P) 100 V120ZA6(P) 100 V24ZA50(P) V24ZA50(P) 90 V24ZA50(P) V24ZA50(P) V100ZA15(P) 90 V18ZA40P(P) 80 V18ZA40P(P) V18ZA40P(P) V82ZA12(P)80 V18ZA40P(P) 70 70 60 60 50 50 500 400 300 200 200 40 MAXIMUM PEAK VOLTS (V) A 800 V36ZA20(P) V36ZA80(P) V36ZA80(P) V180ZA10(P) 700 Radial Lead Varistors > ZAV36ZA20(P) Series V33ZA20(P) V33ZA70(P) 600 V150ZA8(P) V33ZA20(P) V33ZA70(P) A 100 90 80 70 60 V36ZA20(P) V36ZA80(P) V33ZA20(P) V33ZA70(P) V27ZA60(P) V27ZA60(P) V24ZA50(P) V24ZA50(P) V18ZA40P(P) V18ZA40P(P) 50 40 30 40 20 30 30 10 -3 10 -1 10 0 10 1 10 2 10 3 10 -2 10 4 10 -1 10 0 10 1 10 2 10 3 PEAK AMPERES (A) Maximum Clamping Voltage for 20mm Parts PEAK AMPERES (A) 20 100 20 100 -2 -1 0 1 FIGURE 2 12. CLAMPING 3 VOLTAGE FOR -3 V82ZA12(P) - V180ZA10(P) -3 -2 -1 0 1 FIGURE 2 11. CLAMPING 3 10 4 VOLTAGE FOR V18ZA40(P) - V 10 4 V39ZA20(P) 10 -3 10 -110 10 0 10 10 1 10 10 2 10 10 3 10 10 4 10 10 -2-10 V180ZA20(P) V18ZA20(P) - V36ZA80(P) 10 -210 10 -110 10 0 10 10 1 10 10 2 10 10 3 10 10 4 10 10 -3 PEAK PEAK PEAK AMPERES (A)AMPERES (A) PEAK AMPERES (A)AMPERES (A) 200 100 10 -3 10 -2 11. CLAMPING VOLTAGE FOR V82ZA12(P) - V180ZA10(P) 12. CLAMPING VOLTAGE FOR V18ZA40(P) 1,000 300 FIGURE 11. FIGURE CLAMPING VOLTAGE FOR V82ZA12(P) - V180ZA10(P) FIGURE 12. FIGURE CLAMPING VOLTAGE FOR V18ZA40(P) - V36ZA80(P)- V36ZA80(P) MAXIMUM CLAMPING VOLTAGE MODEL SIZE 20mm 18 TO 36VN(DC) RATING TA = -55oC TO 85oC 1,000 40 30 20 10 -3 10 4 10 -2 10 -1 Figure 11 200 100 50 10 0 10 1 PEAK AMPERES (A) 30 10 2 MAXIMUM PEAKVOLTS (V) 50 MAXIMUM CLAMPING VOLTAGE MODEL SIZE 20mm 39 TO 180VM(AC) RATING 500 TA = -55oC TO 85oC 1,000 MAXIMUM CLAMPING VOLTAGE MAXIMUM CLAMPING VOLTAGE V180ZA20(P) MODEL SIZE MODEL 20mm SIZE 20mm 39 TO 180VM(AC) RATINGV180ZA20(P) V150ZA20(P) 39 TO 180VM(AC) RATING V150ZA20(P) 300 oC TO 85oC 500 o o T = -55 500 TA = -55 C TO A 85 C V120ZA20(P) V120ZA20(P) V100ZA20(P) V100ZA20(P) 200 300 300 MAXIMUM PEAKVOLTS (V) V36ZA20(P) V36ZA80(P) V33ZA20(P) V33ZA70(P) V27ZA60(P) V27ZA60(P) V24ZA50(P) V24ZA50(P) V18ZA40P(P) V18ZA40P(P) 100 90 80 70 60 MAXIMUM PEAKVOLTS (V) MAXIMUM PEAK VOLTS (V) 200 - V180ZA10(P) 200 100 50 10 3 10 4 V68ZA20(P) V56ZA20(P) V47ZA20(P) V39ZA20(P) 100 V68ZA20(P) V68ZA20(P) 50 V56ZA20(P) V56ZA20(P) V47ZA20(P) V47ZA20(P) V39ZA20(P) 30 V82ZA20(P) V82ZA20(P) V39ZA20(P) 10 -3 10 -2 30 V180ZA20(P) V150ZA20(P) V120ZA20(P) V100ZA20(P) V82ZA20(P) 10 -1 10 0 10 1 PEAK AMPERES (A) 10 2 10 3 10 4 Figure 12 -2 -1 0 1 2 4 13. -2 10 -3 1010 10 3 CLAMPING 10 4 VOLTAGE FOR V39ZA20(P) - V180ZA20(P) 10 -3 10 -1 10 10 0 10 10 1 10 10 2 1010 3FIGURE FIGURE 12. CLAMPING VOLTAGE FOR V18ZA40(P) -10V36ZA80(P) PEAK PEAK AMPERES (A)AMPERES (A) Pulse13.Rating Curves FIGURE CLAMPING VOLTAGE FOR V39ZA20(P) - V180ZA20(P) FIGURE 13. CLAMPING VOLTAGE FOR V39ZA20(P) - V180ZA20(P) Repetitive Surge Capability for 5mm Parts 50 2 10 10 10 SURGE CURRENT (A) SURGE CURRENT (A) 20 1 2 10 4 5 10 6 10 10 10 4 10 5 6 10 10 2 5 V68ZA20(P) V56ZA20(P) 10 3 10 3 V47ZA20(P) 2 2 V82ZA20(P) V39ZA20(P) 5 10 2 1 1 0.5 10 3 10 -1 10 0 10 1 0.5 10 2 PEAK AMPERES (A) 0.2 0.1 20 0.1 20 100 10 3 1 0.5 0.2 10 4 0.2 5 10 2 2 INDEFINITE 0.1 20 10 4 100 100 50 50 10 5 6 1 10 2 SURGE CURRENT (A) 20 2 SIZE 5mm MODEL SIZE10MODEL 5mm 10 V8ZA05(P) V8ZA05(P) SURGE CURRENT (A) 1 20 100 MODEL SIZE 5mm V18ZA05(P) - V68ZA05(P) V8ZA05(P) 1 20 10 2 10 10 3 2 1 1 2 15 20 10 2 10 10 3 10 4 5 10 6 10 2 15 5mm MODEL SIZE MODEL 5mm 20 SIZE 4 10 10 2 V12ZA05(P) -V12ZA05(P) V68ZA05(P) - V68ZA05(P) 10 5 6 3 10 10 10 2 15 10 4 5 10 6 10 2 1 INDEFINITE 0.5 0.2 0.1 1,000 10,000 20 100 1,000 0.2 IMPULSE DURATION (s) IMPULSE DURATION (s) 0.2 0.1 0.1 FIGURE 14. SURGE CURRENT RATING FOR (P) FIGURE 15. SURGE CURRENT RATING CURVES FOR 100 1,000 10,000 20 CURVES 100V8ZA05 1,000 10,000 1,000 10,000 20 100 1,000 10,000 IMPULSE(s) DURATION (s) IMPULSE DURATION (s) V12ZA05(P) - V68ZA05(P) IMPULSE DURATION IMPULSE DURATION (s) INDEFINITE 100 INDEFINITE AMPING VOLTAGE FOR V39ZA20(P) - V180ZA20(P) FigureFIGURE 13 FigureSURGE 14 100 FIGURE 14. SURGE CURRENT RATING CURVES FOR V8ZA05(P) 15. SURGERATING CURRENT RATING CURVES FOR 14. FIGURE 15. FIGURE CURRENT CURVES FOR 1 SURGE CURRENT RATING CURVES FOR V8ZA05(P) 15 2 50 V82ZA05(P) - V750ZA05(P) 1013 200 2 R V8ZA05(P) MODEL SIZE 5mm V82ZA05(P) - V750ZA05(P) 0.2 5 100 1,000 INDEFINITEIMPULSE DURATION (s) 1 0.2 20 100 Figure 15 1,000 IMPULSE DURATION ( s) 10,000 1 200 100 50 20 10 102 103 2 10 104 5 10 6 10 MODEL SIZE 7mm V8ZA1(P) - V12ZA1(P) 102 20 103 10 5 2 1 INDEFINITE 0.5 0.2 10,000 FIGURE 16. SURGE CURRENT RATING CURVES FOR V82ZA05(P) - V750ZA05(P) 500 2 50 INDEFINITE 0.1 2 20 1 100 FIGURE 15. SURGE CURRENT RATING CURVES FOR 0.5 V12ZA05(P) - V68ZA05(P) RRENT (A) 10,000 V12ZA05(P) V12ZA05(P) - V68ZA05(P)- V68ZA05(P) Note: Repetitive surge capability is qualified and tested based on 8/20us current waveform (not combination waveform) and UL1449 40.7.3 (Edition 4) test condition. 200 103 4 10 5 10 6 10 100 15 2 50 102 1 20 0.5 10 MODEL SIZE 5mm V12ZA05(P) - V68ZA05(P) SURGE CURRENT (A) 10 2 SURGE CURRENT (A) CURRENT (A) SURGE 20 500 10 10 4 5 10 6 10 MODEL SIZE 7mm V18ZA1(P) - V68ZA2(P) 104 5 10 6 10 20 100 1,000 IMPULSE DURATION ( s) 10,000 FIGURE 17. SURGE CURRENT RATING CURVES FOR V8ZA1(P) - V12ZA1(P) 2,000 1,000 500 1 200 100 MODEL SIZE 7mm V82ZA2(P) - V180ZA1(P) 2 10 RENT (A) ZE 5mm MODEL SIZE 5mm V12ZA05(P) - V68Z 1 INDEFINITE INDEFINITE 0.5 0.5 1 50 SURGE CURRENT (A) PulseCurves Rating Curves Pulse Rating SURGE CURRENT (A) LAMPING VOLTAGE 20mm V180ZA20(P) - V12ZA05P AC) RATING V8ZA05PV150ZA20(P) O 85oC V120ZA20(P) 50 50 V100ZA20(P) 0 -2 MAXIMUM CLAMPING VOLTAGE MAXIMUM CLAMPING VOLTAGE MODEL SIZE MODEL 20mm SIZE 20mm 18 TO 36V RATING N(DC) 18 TO200 36VN(DC) RATING -55oC TO 85oC T = -55oC TOTA 85=oC MAXIMUM PEAK VOLTS (V) 300 MAXIMUM PEAK VOLTS (V) 1,000 900 800 700 600 500 400 300 2,000 200 Metal-Oxide Varistors (MOVs) 1,000 900 MAXIMUM PEAK VOLTS (V) 2,000 MAXIMUM PEAK VOLTS (V) Continued) 10 3 MAXIMUM CLAMPING VOLTAGE MAXIMUM CLAMPING VOLTAGE 3,000 MODEL SIZE MODEL 14mm SIZE 14mm 82 TO 180VN(DC) RATING RATING 82 TO 180VN(DC) -55oC TO 85oC TA =2,000 -55oC TOTA 85=oC 3,000 MAXIMUM PEAK VOLTS (V) 4,000 102 (c) 2018 Littelfuse, Inc. 103 Specifications are subject to change without notice. 104 5 Revised: 12/12/18 10 106 200 102 5 2 INDEFINITE 0.55 10,000 INDEFINITE 1 20 100 0.5 Figure 15 FIGURE 17. 0.2 20 INDEFINITE 1,000 IMPULSE DURATION ( s) IMPULSE DURATION ( s) 10 5 100 1 103 104 105 106 15 102 INDEFINITE 50 10 0.2 INDEFINITE 205 0.5 IMPULSE DURATION ( s) 2100 MODEL SIZE 7mm MODEL SIZE 7mm V8ZA1(P) - V12ZA1(P) V82ZA2(P) - V180ZA1(P) 100 INDEFINITE 2 Figure 18 FIGURE 20. 20 10,000 100 20 10 1,000 IMPULSE DURATION ( s) 10,000 SURGE CURRENT RATING CURVES FOR V8ZA2(P) - V127ZA2(P) 1 1,000 10,000 20 100 1,000 IMPULSE DURATION ( s) IMPULSE DURATION ( s) INDEFINITE 100 1,000 10,000 IMPULSE DURATION ( s) INDEFINITE100 1,000 10,000 IMPULSERATING DURATION ( s) FIGURE 21. SURGE CURRENT CURVES FOR 2 V18ZA2(P) - V68ZA3(P) FIGURE 20. SURGE CURRENT RATING CURVES FOR 1 V8ZA2(P) - V127ZA2(P) 10,000 20 100 1,000 IMPULSE DURATION ( s) 10,000 Figure 17 2 1 20 SURGE CURRENT (A) SURGE CURRENT (A) 100 10,000 10 INDEFI 1 20 FIGURE 21. S V INDEFINITE 1 1,000 10,000 20 100 1,000 IMPULSE DURATION ( s)IMPULSE DURATION ( s) 10,000 50 20 100 1,000 10 IMPULSE DURA TION ( s) INDEFINITE 10,000 1,000 500 1 MODEL SIZE 10mm V18ZA2(P) - V68ZA3(P) 5,000 2 200 100 102 3 50 10 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. 20 Revised: 12/12/18 10 104 105 106 1 2,000 2 1,000 15 500 200 100 50 1,000 500 1 200 10 100 50 20 10 5 1 20 10,000 FIGURE 2,000 MODEL SIZE 14mm V82ZA12(P) - V180ZA10(P) 102 3 10 104 105 106 2 2 V180ZA5 FIGURE 19. SURGE CURRENT RATING CURVES FOR V82ZA2(P) - V180ZA1(P) FIGURE 22. SURGE CURRENT RATING CURVES FOR V82ZA4(P) - V180ZA5(P) Note: Repetitive surge capability is qualified and tested based on 8/20us current waveform (not combination waveform) and UL1449 40.7.3 (Edition 4) test condition. MODEL SIZE 10mm V8ZA2(P) - V12ZA2(P) 20 10 5 FIGURE 21. SURGE CURRENT RATING CURVES FOR V18ZA2(P) - V68ZA3(P) 2 20 100 1,000 IMPULSE DURATION ( s) Figure 20 GE CURRENT (A) 104 5 10 6 10 SURGE SURGE CURRENT (A)CURRENT (A) SURGE CURRENT (A) T RATING CURVES FOR A2(P) 3 50 10 2 1 20 10,000 0.2 20 0.5 1 2010 0.2 520 SURGE CURRENT (A) 1,000 E DURATION ( s) 100 102 20 5 2 0.5 TING CURVES FOR ) 2 200 SURGE CURRENT (A) 5 10,000 FIGURE CURRENT CURVES FOR 10,0001,000 1 20 19. SURGE100 1,000 20 RATING 100 INDEFINITE DURATION ( s) IMPULSE DURATION ( s) V82ZA2(P) IMPULSE - V180ZA1(P) 10,000 1 500 2 Figure 16 Figure 19CURRENT FIGURE 18. SURGE CURRENT CURVES FOR RATING CURVES FOR FIGURE 19. SURGE RATING CURVES FORRATING CURVES FOR FIGURERATING 20. SURGE CURRENT FIGURE 21. SURGE CURRENT 1,000 MODEL- SIZE 10mm MODEL SIZE 10mm V18ZA1(P) - V68ZA2(P) V8ZA2(P) V82ZA2(P) - V180ZA1(P) V127ZA2(P) V18ZA2(P) - V68ZA3(P) 0.21 V18ZA2(P) - V68ZA3(P) 1,000 V8ZA2(P) - V12ZA2(P) 10,000 20 100 1,000 10,000 500 DURA TION ( s) 500 2 IMPULSE DURATION ( s) 1,000 06 MODEL SIZE 10mm MODEL SIZE 10mm V82ZA2(P) - V180ZA1(P) 1 V82ZA4(P) - V180ZA5(P) 1 V18ZA2(P) - V68ZA3(P) 200 T RATING CURVES FOR FIGURE CURVES- V12ZA2(P) FOR 500 104RATING 4 V8ZA2(P) 200 2 17. SURGE CURRENT 10 5 10 6 5 0ZA05(P) V8ZA1(P) V12ZA1(P) 2 10 10 100100 10210 106 200 2,000 5,000 104 3 2 MODEL SIZE 7mm MODEL SIZE 7mm MODEL SIZE 10mm 50 10 101 105 100 102 1 4 V18ZA1(P) V68ZA2(P) V82ZA2(P) V180ZA1(P) 50 V82ZA4(P) - V180ZA5(P) 1,000 10 5 3 106 10 2,000 10 6 2 3 20 10 2 50 10 4 20 500 10 1,000 103 105 6 10 15 10 104 10 200 500 15 20 105 5 102 2 6 10 10 100 10 5 2 INDEFINITE 200 103 50 INDEFINITE 100 INDEFINITE 1 5 2 1,000 ATION ( s) 1,000 5 0.5 20 2 0.2 5200 INDEFI V18ZA2(P) - V68ZA3(P) MODEL SIZE 7mm FIGURE 16. SURGE CURRENT CURVES FIGURE 17. SURGE CURRENT RATING CURVES FOR V82ZA2(P) -FOR V180ZA1(P) FIGURERATING 18. SURGE CURRENT RATING CURVES FOR FIGURE 19. SURGE CURRENT RATING CURVES FOR 1,000 V82ZA05(P) V750ZA05(P) V8ZA1(P) - V12ZA1(P)V82ZA2(P) - V180ZA1(P) V18ZA1(P) - V68ZA2(P) 2 500 500 2,000 500 1,000 103 MODEL SIZE 7mm MODEL SIZE 7mm 1 15 4 1 MODEL SIZE 10mm 1 4 10V18ZA1(P) - V68ZA2(P) V82ZA2(P) - V180ZA1(P) MODEL SIZE 10mm 1,000 200 1 10 200 2 5 V18ZA2(P) - V68ZA3(P) 4 V8ZA2(P) V12ZA2(P) 2 500 10 5 200 2 105 6 10 6 10 2 10 6 10 10 500 2 15 100 100 10 10 100 103 200 15 50200 102 104 104 200 102 50 105 2 2 MODEL SIZE 7mm 105 100 1 10 10 50 3 6 3 106 V8ZA1(P) V12ZA1(P) 100 10 10 104 2 100 10 20 3 20 20 105 6 50 10 10 50 10 50 1010 10 0.2 TING CURVES FOR ) 103 1 10,000 102 5 5 5 20 INDEFINITE 103 2 10 2 INDEFINITE 2 INDEFINITE 15 1 1 0.5 20 100 1,000 0.5 IMPULSE DURATION ( s) 2 10,000 102 20 10 1,000 500 GE CURRENT (A) 1,000 ATION ( s) 2 SURGE CURRENT (A) MODEL SIZE 5mm V82ZA05(P) - V750ZA05(P) 5 SURGE CURRENT RATING CURVES FOR 0.2 V8ZA1(P) 100 - V12ZA1(P) 1,000100 10,000 20 1,000 2,000 6 10 0.5 V18ZA1(P) - V68ZA2(P) 1 06 103 1 SURGE CURRENT (A) SURGE CURRENT (A) SURGE CURRENT (A) MODEL SIZE 7mm V18ZA1(P) - V68ZA2(P) 20 102 20 FIGURE 19. S V V8ZA1(P) - V12ZA1(P) SURGE CURRENT (A) ING CURVES FOR 5(P) 50 50 1 20 2 102 2,000 50 1031 21,000 104 20 2 105 6 10 500 10 200 MODEL SIZE 7mm 1 MODEL SIZE 5mm 100 4 V18ZA1(P) - V68ZA2(P) 10 V82ZA05(P) V750ZA05(P) 2 105 6 10 10 50 SURGE CURRENT (A) 1,000 TION ( s) 2 INDEFINITE V18ZA1(P) - V68ZA2(P) 1,000 10,000 MODEL SIZE 10mm IMPULSE DURA TIONV8ZA2(P) ( s) - V12ZA2(P) 104 5 10 6 FIGURE 17. SURGE CURRENT RATING CURVES FOR 10 100 10 200 102 100 2 500 0.2 20 1 10,000 SURGE CURRENT (A) SURGE CURRENT (A) 500 1 103 4 10 200 5 10 6 100 10 15 2 20 0.2 1,000 SURGE CURRENT (A) SURGE CURRENT (A) SURGE CURRENT (A) 2 500 10 20 1 3 10 2 200 10 100 10 5 50 102 10 1 100 MODEL SIZE 7mm IMPULSE DURATION ( s) V8ZA1(P) - V12ZA1(P) 15 200 5 5 1 FIGURE SURGE CURRENT RATING CURVES FOR 10516. 106 V82ZA05(P) - V750ZA05(P) 10 50 10 0.5 104 SURGE CURRENT (A) 100 102 INDEFINITE 103 20 V8ZA2(P) - FIGURE V12ZA2(P) 18. SURGE CURRENT RATING CURVES FOR 0.2 20 1 MODEL SIZE 7mm V8ZA1(P) - V12ZA1(P) 100 1,000 2 Repetitive20Surge Capability for 10mm Parts 10,000 IMPULSE DURATION ( s) 0.5 200 MODEL SIZE 5mm V82ZA05(P) - V750ZA05(P) 2 10 104 5 10 6 10 0.2 INDEFINITE 1 2 5 50 0.5 10 1 10100 1 20 Repetitive Surge Capability for 7mm Parts 2 V8ZA1(P) - V12ZA1(P) 20200 SURGE CURRENT (A) 10 50 SURGE CURRENT (A) 100 MODEL SIZE 5mm V82ZA05(P) - V750ZA05(P) 103 SURGE CURRENT (A) 2 200 103 4 10 5 10 6 10 SURGE CURRENT (A) Radial Lead Varistors >500 ZA1Series 2 500 102 50 SURGE CURRENT (A) Metal-Oxide Varistors (MOVs) 10 5 10 6 10 2 15 100 200 100 50 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series Repetitive Surge Capability for 14mm Parts V82ZA12(P) - V180ZA10(P) 15 100 5,000 50 20 10 INDEFINITE 2 1 20 10,000 V180ZA5 OR 100 Figure 21 1,000 IMPULSE DURATION ( s) 2,000 2 1,000 15 SURGE CURRENTSURGE (A) CURRENT (A) 10,000 20 200 10 100 5 50 2 2020 10 R INDEFINITE 100 1,000 IMPULSE DURATION ( s) 103 MODEL SIZE 20mm V18ZA40(P) - V68ZA20(P) 105 15 103 INDEFINITE 104 105 100 INDEFINITE 1,000 IMPULSE DURATION ( s) 2 100 1,000 MODEL 20 SIZE 20mm V120ZA20(P) - V180ZA20(P)IMPULSE DURATION ( s) Figure 23 R 10,000 5,000 10,000 FIGURE 25. SURGE CURRENT RATING CURRENT FOR V18ZA40(P) - V68ZA20(P) 103 100 104 50 105 10,000 15 1,000 500 102 103 200 104 105 106 100 50 20 10 Figure 24 200 103 MODEL SIZE 20mm 100 104- V68ZA20 V18ZA40(P) 5 106 50 10 1 100 1 2 FIGURE 25. SURGE CURRENT RATING CURRENT FOR 2,000 15 V18ZA40(P) - V68ZA20(P) 1,000 102 500 20 INDEFINITE 10 1 INDEFINITE 20 100 1,000 IMPULSE DURATION ( s) FIGURE 26. SURGE CURRENT RATING CURVES FOR V120ZA20 20 100 1,000 10,000 IMPULSE DURATION ( s) FIGURE 26. SURGE CURRENT RATING CURVES FOR V120ZA20(P) - V180ZA20(P) 10,000 URRENT RATING CURVES FOR V120ZA20(P) - V180ZA20(P) 1,000 1 1,000 1 SIZE 20mm IMPULSE DURAMODEL TION ( s) V120ZA20(P) - V180ZA20 IMPULSE DURATION ( s) 100 2 20 FIGURE 25. SURGE V18ZA4 V120ZA20(P) - V180ZA20(P) Note: Repetitive surge capability is qualified and tested based on 8/20us current waveform (not combination waveform) and UL1449 40.7.3 (Edition 4) test condition. 1,000 INDEFINITE 5 NOTE: If pulse ratings are exceeded, a shift of VN(DC)(at specified current) of more then +/-10% could result. This type of shift, which normally results in a decrease of VN(DC), may result in the device not meeting the original published specifications, but does not prevent the device from continuing to function,MODEL and toSIZE provide 20mmample protection. 100 20 10 TE TE 15 102 2 2 10,000 1 5 5 1 2 10,00020 5,000 2 3 MODEL SIZE10 20mm 200 4 V120ZA20(P) - V180ZA20(P) 10 100 105 50 106 1 2 2,000 106 102 200 500 5 FIGURE 24. SURGE CURRENT RATING CURVES FOR V82ZA12(P) - V180ZA10(P) FIGURE 25. SURGE CURRENT RATING CURRENT FOR 5 V18ZA40(P) - V68ZA20(P) 10,000 Figure 22 V82ZA12(P) - V180ZA10(P) 10 2 4 1 102 3 10 104 105 2,000106 2 1,000 15 500 102 1,000 20 100 1,000 10,000 IMPULSE DURATION10 ( s) INDEFINITE V82ZA20(P) - V180ZA20(P) 106 FIGURE 24. SURGE CURRENT RATING CURVES FOR 102 200 2,000 100 1,000 50 500 2 20 10,000 V18ZA40(P) - V68ZA20(P) V18ZA40(P)500 - V68ZA20(P) mm 80ZA10(P) 5 50 20 INDEFINITE 10 2 10 15 500 100 1 Capability for 20mm Parts 20 Repetitive Surge 2 MODEL SIZE 20mm 1,000 1,000 2,000 MODEL SIZE 14mm V82ZA12(P) - V180ZA10(P) 10 3 10 50 104 105 106 20 200 10 2,000 2 MODEL 200 SIZE 14mm V82ZA12(P) - V180ZA10(P) 2 100 500 FIGURE 23. SURGE CURRENT RATING CURVES FOR 5 V18ZA3(P) - V68ZA10(P) mm 80ZA10(P) 1 1 2,000 SURGE CURRENT (A) SURGE CURRENT (A) 200 102 5 5,000 MODEL SIZE 14mm 103 V18ZA3(P) - V68ZA10(P) 104 105 6 10 SURGE CURRENT (A) 1 2 SURGE CURRENT (A) 500 SURGE CURRENT (A) 1,000 SURGE CURRENT (A) 0mm 80ZA5(P) SURGE CURRENT (A) V18ZA3(P) - V68ZA10(P) 10,000 IMPULSE DURATION ( s) URRENT RATING CURVES FOR V120ZA20(P) - V180ZA20(P) (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series Wave Solder Profile Non Lead-free Profile Lead-free Profile 300 300 250 TEMPERATURE (C) TEMPERATURE (C) Maximum Wave 260C Maximum Wave 240C 250 200 150 100 200 150 100 50 50 0 0 0 0.5 1 Figure 25 1.5 2 2.5 3 3.5 TIME(MINUTES) Physical Specifications 4 0 0.5 1 1.5 Figure 26 2 2.5 3 3.5 4 TIME(MINUTES) Environmental Specifications Operating Ambient Temperature Range -55C to +85C Solderability per MIL-STD-202, Method 208 Storage Temperature Range -55C to +125C Insulating Material Cured, flame retardant epoxy polymer meets UL94V-0 requirements Humidity Aging +85C, 85% RH,1000 hours +/-10% typical voltage change Device Labeling Marked with LF, voltage, UL/CSA logos, and date code Thermal Shock +85C to -40C 5 times +/-10% typical voltage change Solvent Resistance MIL-STD-202, Method 215 Moisture Sensitivity Level 1, J-STD-020 Lead Material Copper Clad Steel Wire Soldering Characteristics (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series Product Dimensions (mm) oD A CRIMPED AND TRIMMED LEAD Radial lead types can be supplied with combination preformed crimp and trimmed leads. This option is supplied to the dimensions shown. ATRIM SEATING PLANE e1 *Seating plane interpretation per IEC-717 LTRIM ob 25.4 (1.00) MIN To order this crimped and trimmed lead style, standard radial type model numbers are changed by replacing the model letter "ZA" with "ZC." This option is supplied in bulk only. e Example: E Standard Model Order As V18ZA3P V18ZC3P For crimped leads without trimming and any varitions to the above, contact Littelfuse. 5mm Size 7mm Size 10mm Size 14mm Size 20mm Size Dimension VRMS Voltage Model Min. mm (in) Max. mm (in) Min. mm (in) Max. mm (in) Min. mm (in) Max. mm (in) Min. mm (in) Max. mm (in) Min. mm (in) Max. mm (in) A All - 10 (0.394) - 12 (0.472) - 16 (0.630) - 20 (0.787) - 26.5 (1.043) OD All - 7 (0.276) - 9 (0.354) - 12.5 (0.492) - 17 (0.669) - 23 (0.906) All 4 (0.157) 6 (0.236) 4 (0.157) 6 (0.236) 6.5 (0.256) 8.5 (0.335) 6.5 (0.256) 8.5 (0.335) V8ZAV56ZA 1 (0.039) 3 (0.118) 1 (0.039) 3 (0.118) V68ZAV100ZA 1.5 (0.059) 3.5 (0.138) 1.5 (0.059) 3.5 (0.138) V120ZAV180ZA 1 (0.039) 3 (0.118) 1 (0.039) 3 (0.118) 1 (0.039) 3 (0.118) 1 (0.038) 3 (0.118) 1 (0.038) 3 (0.118) V205ZAV750ZA 1.5 (0.059) 3.5 (0.138) - - - - - - - - V8ZAV56ZA - 5 (0.197) - 5 (0.197) - 5 (0.197) - 5 (0.197) - 5 (0.197) V68ZAV100ZA - 5.6 (0.220) - 5.6 (0.220) - 5.6 (0.220) - 5.6 (0.220) - 5.6 (0.220) V120ZAV180ZA - 5 (0.197) - 5 (0.197) - 5 (0.197) - 5 (0.197) - 5 (0.197) V205ZAV750ZA - 5.6 (0.220) - - - - - - - - Ob All 0.585 (0.023) 0.685 (0.027) 0.585 (0.023) 0.685 (0.027) 0.76 (0.030) 0.86 (0.034) 0.76 (0.030) 0.86 (0.034) 0.76 (0.030) 0.86 (0.034) ATRIM All - 13.0 (0.512) - 15 (0.591) - 19.5 (0.768) - 22.5 (0.886) - 29.0 (1.142) LTRIM All 2.41 (0.095) 4.69 (0.185) 2.41 (0.095) 4.69 (0.185) 2.41 (0.095) 4.69 (0.185) 2.41 (0.095) 4.69 (0.185) 2.41 (0.095) 4.69 (0.185) e (see notes below) e1 E 1 (0.039) 3 (0.118) 1 (0.039) 1.5 (0.059) 3.5 (0.138) 1.5 (0.059) 3 (0.118) 3.5 (0.138) 6.5 (0.256) 8.5 (0.335) (note 1 below) (note 1 below) 1 (0.039) 3 (0.118) 1.5 (0.059) 3.5 (0.138) NOTES: Dimensions in millimeters, inches in parentheses. 1. For 20mm size devices, a 10mm "e" dimension option is also available. Please refer to "Ordering Notes" section "X10" option code for additional information. 2. V24ZA50(P) and V24ZC50(P) only supplied with lead spacing of 6.35mm -/+0.5mm (0.25 -/+0.0196) Dimension e = 5.85 min. Does not apply to Tape and Reel parts. (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series Tape and Reel Specifications 5 and 7mm Devices 10, 14 and 20mm Devices CRIMPED LEADS "ZT" P2 P2 P2 P2 P2P2 HH1 1 HH 11 H1H1 HH0 0 HH 00 H0H0 CRIMPED LEADS "ZT" P2 P2 P2 P2 P2P2 EE EE DP DP E E DP DH DP DH DH DH DH DH DH DPDP DH DH DH DH DH WW WW WW P1 P1 P1 P1 P0 P0 P0 P1P1 P0 P0P0 FF FF FF tt tt t t Crimped CrimpedLeads Leads"ZT" "ZT" Crimped CrimpedLeads Leads"ZT" "ZT" Crimped CrimpedLeads Leads"ZT" "ZT" STRAIGHT LEADS "ZS" P2 P2 P2 P2 P2P2 PP PP DP DP P PDP DP DPDP DD0 DD0 DD0 DD0 DD0 DD0 tt tt Ho Ho Ho Ho HoHo DD0 DD0 DD0 DD0 DD0 DD0 Under-crimped Under-crimpedLeads Leads"ZU" "ZU" Under-crimped Under-crimpedLeads Leads"ZU" "ZU" Under-crimped Under-crimpedLeads Leads"ZU" "ZU" FF FF FF tt tt t t tt tt t t PP PP DP DP P PDP DP EE EE DP DP DP DH DP DH DH DH E E DH DH DH DPDP DH DH DH DH DH DD0 DD0 DD0 DD0 DD0 DD0 W0 W0 W2 W2 W1 W1 W0 W0 W2 W2 W1 W1 W0 W0W2 W2W1 W1 Db Db Db Db DbDb WW WW WW P1 P1 P1 P1 P1P1 P0 P0 P0 P0 P0P0 P2 P2 P2 P2 P2P2 WW WW WW P1 P1 P1 P1 P0 P0 P0 P1P1 P0 P0P0 FF FF FF FF FF FF tt tt t t Straight StraightLeads Leads"ZS" "ZS" Straight StraightLeads Leads"ZS" "ZS" Straight "ZS" StraightLeads Leads "ZS" CRIMPED LEADS "ZU" UNDER UU UU UU W0 W0 W2 W2 W1 W1 W0 W0 W2 W2 W1 W1 W0 W0 W2 W2W1 W1 Db Db Db Db DbDb P1 P1 P1 P1 P0 P1P1P0 P0 P0 P0P0 HH HH HH EE EE DP DP DP DH DP DH DH DH E E DH DH DH DPDP DH DH DH DH DH HH1 1 HH 11 H1H1 WW WW WW HH1 1 HH 11 H1H1 t t Straight StraightLeads Leads"ZS" "ZS" Straight StraightLeads Leads"ZS" "ZS" Straight StraightLeads Leads"ZS" "ZS" UNDER CRIMPED LEADS "ZU" PP PP DP DP P PDP DP DPDP W0 W2 W1 W1 W0 W2 W0 W2 W1 W1 W0 W2 W0 W2W1 W1 W0 W2 DPDP W0 W0 W2 W2 W1 W1 W0 W0 W2 W2 W1 W1 W0 W0W2 W2W1 W1 FF FF FF CC CC CC Db Db Db Db DbDb P2 P2 P2 P2 P2P2 WW WW WW P2 P2 P2 P2 P2P2 DD0 DD0 DD0 DD0 DD0 DD0 EE EE DP DP E E DP DH DP DH DH DH DH DH DH DPDP DH DH DH DH DH Db Db Db Db DbDb P1 P1 P1 P1 P0 P0 P0 P1P1 P0 P0P0 EE EE DP DP E E DP DH DP DH DH DH DH DH DH DPDP DH DH DH DH DH Crimped CrimpedLeads Leads"ZT" "ZT" Crimped CrimpedLeads Leads"ZT" "ZT" Crimped CrimpedLeads Leads"ZT" "ZT" STRAIGHT LEADS "ZS" HH1 1 HH 11 H1H1 HH HH HH SEATING SEATING PLANE PLANE SEATING SEATING PLANE PLANE SEATING SEATING PLANE PLANE HH0 0 HH 00 H0H0 W0 W0 W2 W2 W1 W1 W0 W0 W2 W2 W1 W1 W0 W0 W2 W2W1 W1 Db Db Db Db DbDb PP PP DP DP P PDP DP DPDP HH1 1 HH 11 H1H1 CC CC CC SEATING SEATING PLANE PLANE SEATING SEATING PLANE PLANE SEATING SEATING PLANE PLANE DD0 DD0 DD0 DD0 DD0 DD0 PP PP DP DP P PDP DP DPDP PP PP DP DP P PDP DP EE EE DP DP E E DP DH DP DH DH DH DH DH DH DPDP DH DH DH DH DH DPDP UU UU UU W0 W0 W2 W2 W1 W1 W0 W0 W2 W2 W1 W1 W0 W0 W2 W2W1 W1 HH1 1 HH 11 H1H1 Ho Ho Ho Ho HoHo DD0 DD0 DD0 DD0 DD0 DD0 Db Db Db Db DbDb WW WW WW P1 P1 P1 P1 P0 P1P1P0 P0 P0 P0P0 FF FF FF tt tt t t Under-crimped Under-crimpedLeads Leads"ZU" "ZU" Under-crimped Under-crimpedLeads Leads"ZU" "ZU" Under-crimped Under-crimpedLeads Leads"ZU" "ZU" Refer to next page for dimension measurement specifics. (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series Tape and Reel Specifications (continued) NOTES: * Radial devices on tape are supplied with crimped leads, straight leads, or under-crimped leads * Leads are offset by product dimension e1 * Conforms to ANSI and EIA specifications * Can be supplied to IEC Publication 286-2 * 5mm parts are available on tape and reel up to 385 VAC only SYMBOL DESCRIPTION 5mm 7mm MODEL SIZE 10mm 14mm 20mm P Pitch of Component 12.7 +/- 1.0 12.7 +/- 1.0 25.4 +/- 1.0 25.4 +/- 1.0 25.4 +/- 1.0 P0 Feed Hole Pitch 12.7 +/- 0.2 12.7 +/- 0.2 12.7 +/- 0.2 12.7 +/- 0.2 12.7 +/- 0.2 P1 Feed Hole Center to Pitch 3.85 +/- 0.7 3.85 +/- 0.7 8.85 +/- 0.7 8.85 +/- 0.7 8.85 +/- 0.7 P2 Hole Center to Component Center 6.35 +/- 1.0 6.35 +/- 1.0 12.7 +/- 0.7 12.7 +/- 0.7 12.7 +/- 0.7 F Lead to Lead Distance 5.0 +/- 1.0 5.0 +/-1.0 7.5 +/- 1.0 7.5 +/- 1.0 7.5 +/- 1.0 h Component Alignment 2.0 Max 2.0 Max 2.0 Max 2.0 Max 2.0 Max W Tape Width 18.0 +1.0 / -0.5 18.0 +1.0 / -0.5 18.0 +1.0 / -0.5 18.0 +1.0 / -0.5 18.0 +1.0 / -0.5 W0 Hold Down Tape Width 12.0 +/- 0.3 12.0 +/- 0.3 12.0 +/- 0.3 12.0 +/- 0.3 12.0 +/- 0.3 W1 Hole Position W2 Hold Down Tape Position 9.0 +0.75 / -0.50 9.0 +0.75 / -0.50 9.0 +0.75 / -0.50 9.0 +0.75 / -0.50 9.0 +0.75 / -0.50 0.5 Max 0.5 Max 0.5 Max 0.5 Max 0.5 Max 18.0 +2.0 / -0.0 18.0 +2.0 / -0.0 18.0 +2.0 / -0.0 18.0 +2.0 / -0.0 18.0 +2.0 / -0.0 16.0 +/- 0.5 16.0 +/- 0.5 16.0 +/- 0.5 16.0 +/- 0.5 16.0 +/- 0.5 H Height from Tape Center to Component Base H0 Seating Plane Height H1 Component Height 29.0 Max 32.0 Max 36.0 Max 40.0 Max 46.5 Max D0 Feed Hole Diameter 4.0 +/- 0.2 4.0 +/- 0.2 4.0 +/- 0.2 4.0 +/- 0.2 4.0 +/- 0.2 t Total Tape Thickness 0.7 +/- 0.2 0.7 +/- 0.2 0.7 +/- 0.2 0.7 +/- 0.2 0.7 +/- 0.2 U Undercrimp Width 8.0 Max 8.0 Max 8.0 Max 8.0 Max 8.0 Max p Component Alignment 3 Max 3 Max 3 Max 3 Max 3 Max Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 Metal-Oxide Varistors (MOVs) Radial Lead Varistors > ZA Series Part Numbering System BASE PART CODES (See Ratings & Specifications tables and notes below) OPTION CODES (See notes below) V XXX ZA XX P W XXXXX For "VARISTOR" See OPTIONS CODES notes below NOMINAL VOLTAGE (V NOM ) (One, Two or Three Digits) SERIES + PACKAGING / LEAD STYLE DESIGNATOR For standard parts, use the BASE PART designator only. For parts with non-standard options (such as additional form, packaging and lead space options), use BASE PART + OPTION CODE. OPTION CODE items are subject to availability and minimum order requirements. Please contact a Littelfuse products representative for additional information or questions (See BASE PART CODES notes below) ZA = Bulk Pack / Straight Leads (standard) ZC = Bulk Pack / Crimped and Trimmed Leads ZS = Tape and Reel / Straight Leads ZT = Tape and Reel / Crimped Leads ZU = Tape and Reel / Under-Crimped Leads RELATIVE ENERGY INDICATOR (One or Two Digits) LEAD-FREE, HALOGEN-FREE AND RoHS COMPLIANT INDICATOR COPPER ELECTRODE Ordering Notes: BASE PART CODES: OPTION CODES: Series + Packaging / Lead Style Designators: X10: 10MM LEAD SPACING OPTION -- Ordering examples: Straight Lead Bulk Pack (standard) Straight Lead Tape & Reel Crimped Lead Tape & Reel V18ZA3P V18ZS3P V18ZT3P Crimped & UnderTrimmed Crimp Lead Lead Tape & Bulk Pack Reel V18ZC3P For 10 -/+1 mm (0.394-/+0.039 in) lead spacing (available on 20mm diameter models only), append standard model BASE PART number with "X10." Example: Standard Model Order As V18ZA40P V18ZA40PX10 V18ZU3P X2855: Nickel Barrier COATED WIRE OPTION -- Crimped lead ZA Series varistors are supplied standard in tape and reel, denoted with "ZT." "ZC" style is supplied in bulk only. "ZU" style is supplied in tape and reel only. For crimped leads without trimming and any varitions other than that described above, please contact Littelfuse. Packaging and Quantities: Littelfuse ZA Series varistors are shipped standard in bulk pack with straight leads and lead spacing outlined in the Package Dimensions section of this data sheet. Contact your Littelfuse sales representative to discuss non-standard options. Tape & Reel Quantities: Device Size Voltage 5mm 7mm 10mm 14mm 20mm All All All < 300V < 300V "S" Reel 1000 1000 500 500 500 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/18 Quantity Per Reel "T" Reel "U" Reel 1000 1000 1000 1000 500 500 500 500 500 400 All standard parts use tinned copper clad steel wire. Nickel Barrier Coated wire is available as an option, consisting of Copper wire with a flashing of Nickel followed by a top coating of Tin. To order append standard model BASE PART number with "X2855." Example: Standard Model Order As V18ZA40P V18ZA40PX2855 X1347: Hi-Temperature phenolic coating option -Phenolic Coated C-III Series devices are available with improved maximum operating maximum temperature of 125C. To order, add X1347 to end of part number (Example: V22ZA3PX1347). For additional information please refer to the section labeled "Phenolic Coating Option" within this document.