ADC128S102 www.ti.com SNAS298F - AUGUST 2005 - REVISED MAY 2013 ADC128S102 8-Channel, 500 ksps to 1 Msps, 12-Bit A/D Converter Check for Samples: ADC128S102 FEATURES DESCRIPTION * * * * * The ADC128S102 is a low-power, eight-channel CMOS 12-bit analog-to-digital converter specified for conversion throughput rates of 500 ksps to 1 MSPS. The converter is based on a successiveapproximation register architecture with an internal track-and-hold circuit. It can be configured to accept up to eight input signals at inputs IN0 through IN7. 1 234 Eight Input Channels Variable Power Management Independent Analog and Digital Supplies SPITM/ QSPITM/ MICROWIRETM/DSP Compatible Packaged in 16-Lead TSSOP APPLICATIONS * * * * * The output serial data is straight binary and is compatible with several standards, such as SPITM, QSPITM, MICROWIRETM, and many common DSP serial interfaces. Automotive Navigation Portable Systems Medical Instruments Mobile Communications Instrumentation and Control Systems KEY SPECIFICATIONS * * * * Conversion Rate 500 ksps to 1 MSPS DNL (VA = VD = 5.0 V) +1.5 / -0.9 LSB (max) INL (VA = VD = 5.0 V) 1.2 LSB (max) Power Consumption - 3V Supply 2.3 mW (typ) - 5V Supply 10.7 mW (typ) The ADC128S102 may be operated with independent analog and digital supplies. The analog supply (VA) can range from +2.7V to +5.25V, and the digital supply (VD) can range from +2.7V to VA. Normal power consumption using a +3V or +5V supply is 2.3 mW and 10.7 mW, respectively. The power-down feature reduces the power consumption to 0.06 W using a +3V supply and 0.25 W using a +5V supply. The ADC128S102 is packaged in a 16-lead TSSOP package. Operation over the extended industrial temperature range of -40C to +105C is ensured. Connection Diagram CS 1 16 SCLK VA 2 15 DOUT AGND 3 14 DIN IN0 4 13 VD IN1 5 12 DGND ADC128S102 IN2 6 11 IN7 IN3 7 10 IN6 IN4 8 9 IN5 Figure 1. TSSOP Package See Package Number PW0016A 1 2 3 4 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. MICROWIRE is a trademark of Texas Instruments. SPI, QSPI are trademarks of Motorola, Inc.. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2005-2013, Texas Instruments Incorporated ADC128S102 SNAS298F - AUGUST 2005 - REVISED MAY 2013 www.ti.com Block Diagram IN0 . . . T/H MUX VA 12-BIT SUCCESSIVE APPROXIMATION ADC AGND AGND IN7 VD SCLK ADC128S102 CS CONTROL LOGIC DIN DOUT DGND Pin Descriptions Pin No. Name Description ANALOG I/O 4 - 11 IN0 to IN7 Analog inputs. These signals can range from 0V to VREF. DIGITAL I/O 16 SCLK Digital clock input. The ensured performance range of frequencies for this input is 8 MHz to 16 MHz. This clock directly controls the conversion and readout processes. 15 DOUT Digital data output. The output samples are clocked out of this pin on the falling edges of the SCLK pin. 14 DIN Digital data input. The ADC128S102's Control Register is loaded through this pin on rising edges of the SCLK pin. 1 CS Chip select. On the falling edge of CS, a conversion process begins. Conversions continue as long as CS is held low. 2 VA Positive analog supply pin. This voltage is also used as the reference voltage. This pin should be connected to a quiet +2.7V to +5.25V source and bypassed to GND with 1 F and 0.1 F monolithic ceramic capacitors located within 1 cm of the power pin. 13 VD Positive digital supply pin. This pin should be connected to a +2.7V to VA supply, and bypassed to GND with a 0.1 F monolithic ceramic capacitor located within 1 cm of the power pin. POWER SUPPLY 3 AGND The ground return for the analog supply and signals. 12 DGND The ground return for the digital supply and signals. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 ADC128S102 www.ti.com SNAS298F - AUGUST 2005 - REVISED MAY 2013 Absolute Maximum Ratings (1) (2) Analog Supply Voltage VA -0.3V to 6.5V Digital Supply Voltage VD -0.3V to VA + 0.3V, max 6.5V Voltage on Any Pin to GND -0.3V to VA +0.3V (3) 10 mA Input Current at Any Pin Package Input Current (3) 20 mA Power Dissipation at TA = 25C ESD Susceptibility (5) See Human Body Model (4) 2500V Machine Model 250V For soldering specifications: see product folder at www.ti.com and http://www.ti.com/lit/SNOA549 Junction Temperature +150C Storage Temperature -65C to +150C (1) (2) (3) (4) (5) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND or VIN > VA or VD), the current at that pin should be limited to 10 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10 mA to two. The absolute maximum junction temperature (TJmax) for this device is 150C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance (JA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax - TA)/JA. In the 16-pin TSSOP, JA is 96C/W, so PDMAX = 1,200 mW at 25C and 625 mW at the maximum operating ambient temperature of 105C. Note that the power consumption of this device under normal operation is a maximum of 12 mW. The values for maximum power dissipation listed above will be reached only when the ADC128S102 is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided. Human body model is 100 pF capacitor discharged through a 1.5 k resistor. Machine model is 220 pF discharged through ZERO ohms Operating Ratings (1) (2) -40C TA +105C Operating Temperature VA Supply Voltage +2.7V to +5.25V VD Supply Voltage +2.7V to VA Digital Input Voltage 0V to VA Analog Input Voltage 0V to VA Clock Frequency (1) (2) 8 MHz to 16 MHz Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. All voltages are measured with respect to GND = 0V, unless otherwise specified. Package Thermal Resistance JA Package 16-lead TSSOP on 4-layer, 2 oz. PCB 96C / W Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 3 ADC128S102 SNAS298F - AUGUST 2005 - REVISED MAY 2013 www.ti.com ADC128S102 Converter Electrical Characteristics (1) The following specifications apply for AGND = DGND = 0V, fSCLK = 8 MHz to 16 MHz, fSAMPLE = 500 ksps to 1 MSPS, CL = 50pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25C. Parameter Test Conditions Typical Limits (2) Units STATIC CONVERTER CHARACTERISTICS Resolution with No Missing Codes Integral Non-Linearity (End Point Method) INL 12 Bits VA = VD = +3.0V 0.4 1 LSB (max) VA = VD = +5.0V 0.5 1.2 LSB (max) +0.4 +0.9 LSB (max) -0.2 -0.7 LSB (min) +0.7 +1.5 LSB (max) VA = VD = +3.0V DNL Differential Non-Linearity VA = VD = +5.0V VOFF Offset Error OEM Offset Error Match FSE Full Scale Error FSEM Full Scale Error Match -0.4 -0.9 LSB (min) VA = VD = +3.0V +0.8 2.3 LSB (max) VA = VD = +5.0V +1.1 2.3 LSB (max) VA = VD = +3.0V 0.1 1.5 LSB (max) VA = VD = +5.0V 0.3 1.5 LSB (max) VA = VD = +3.0V +0.8 2.0 LSB (max) VA = VD = +5.0V +0.3 2.0 LSB (max) VA = VD = +3.0V 0.1 1.5 LSB (max) VA = VD = +5.0V 0.3 1.5 LSB (max) DYNAMIC CONVERTER CHARACTERISTICS FPBW SINAD SNR THD SFDR ENOB ISO (1) (2) 4 Full Power Bandwidth (-3dB) Signal-to-Noise Plus Distortion Ratio Signal-to-Noise Ratio Total Harmonic Distortion Spurious-Free Dynamic Range Effective Number of Bits Channel-to-Channel Isolation VA = VD = +3.0V 8 MHz VA = VD = +5.0V 11 MHz VA = VD = +3.0V, fIN = 40.2 kHz, -0.02 dBFS 73 70 dB (min) VA = VD = +5.0V, fIN = 40.2 kHz, -0.02 dBFS 73 70 dB (min) VA = VD = +3.0V, fIN = 40.2 kHz, -0.02 dBFS 73 70.8 dB (min) VA = VD = +5.0V, fIN = 40.2 kHz, -0.02 dBFS 73 70.8 dB (min) VA = VD = +3.0V, fIN = 40.2 kHz, -0.02 dBFS -88 -74 dB (max) VA = VD = +5.0V, fIN = 40.2 kHz, -0.02 dBFS -90 -74 dB (max) VA = VD = +3.0V, fIN = 40.2 kHz, -0.02 dBFS 91 75 dB (min) VA = VD = +5.0V, fIN = 40.2 kHz, -0.02 dBFS 92 75 dB (min) VA = VD = +3.0V, fIN = 40.2 kHz 11.8 11.3 Bits (min) VA = VD = +5.0V, fIN = 40.2 kHz, -0.02 dBFS 11.8 11.3 Bits (min) VA = VD = +3.0V, fIN = 20 kHz 82 dB VA = VD = +5.0V, fIN = 20 kHz, -0.02 dBFS 84 dB Data sheet min/max specification limits are ensured by design, test, or statistical analysis. Tested limits are specified to TI's AOQL (Average Outgoing Quality Level). Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 ADC128S102 www.ti.com SNAS298F - AUGUST 2005 - REVISED MAY 2013 ADC128S102 Converter Electrical Characteristics (1) (continued) The following specifications apply for AGND = DGND = 0V, fSCLK = 8 MHz to 16 MHz, fSAMPLE = 500 ksps to 1 MSPS, CL = 50pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25C. Parameter Test Conditions Intermodulation Distortion, Second Order Terms IMD Intermodulation Distortion, Third Order Terms Typical Limits (2) Units VA = VD = +3.0V, fa = 19.5 kHz, fb = 20.5 kHz -89 dB VA = VD = +5.0V, fa = 19.5 kHz, fb = 20.5 kHz -91 dB VA = VD = +3.0V, fa = 19.5 kHz, fb = 20.5 kHz -88 dB VA = VD = +5.0V, fa = 19.5 kHz, fb = 20.5 kHz -88 dB ANALOG INPUT CHARACTERISTICS VIN Input Range IDCL DC Leakage Current CINA Input Capacitance 0 to VA V 1 A (max) Track Mode 33 pF Hold Mode 3 pF DIGITAL INPUT CHARACTERISTICS VA = VD = +2.7V to +3.6V 2.1 VA = VD = +4.75V to +5.25V 2.4 V (min) Input Low Voltage VA = VD = +2.7V to +5.25V 0.8 V (max) IIN Input Current VIN = 0V or VD 0.01 1 A (max) CIND Digital Input Capacitance 2 4 pF (max) VIH Input High Voltage VIL V (min) DIGITAL OUTPUT CHARACTERISTICS VOH Output High Voltage ISOURCE = 200 A, VA = VD = +2.7V to +5.25V VD - 0.5 V (min) VOL Output Low Voltage ISINK = 200 A to 1.0 mA, VA = VD = +2.7V to +5.25V 0.4 V (max) IOZH, IOZL Hi-Impedance Output Leakage Current VA = VD = +2.7V to +5.25V 1 A (max) 4 pF (max) COUT Hi-Impedance Output Capacitance (3) 2 Output Coding Straight (Natural) Binary POWER SUPPLY CHARACTERISTICS (CL = 10 pF) VA, VD Analog and Digital Supply Voltages Total Supply Current Normal Mode ( CS low) IA + ID Total Supply Current Shutdown Mode (CS high) Power Consumption Normal Mode ( CS low) PC Power Consumption Shutdown Mode (CS high) (3) VA VD 2.7 V (min) 5.25 V (max) VA = VD = +2.7V to +3.6V, fSAMPLE = 1 MSPS, fIN = 40 kHz 0.76 1.5 mA (max) VA = VD = +4.75V to +5.25V, fSAMPLE = 1 MSPS, fIN = 40 kHz 2.13 3.1 mA (max) VA = VD = +2.7V to +3.6V, fSCLK = 0 ksps 20 nA VA = VD = +4.75V to +5.25V, fSCLK = 0 ksps 50 nA VA = VD = +3.0V fSAMPLE = 1 MSPS, fIN = 40 kHz 2.3 4.5 mW (max) VA = VD = +5.0V fSAMPLE = 1 MSPS, fIN = 40 kHz 10.7 15.5 mW (max) VA = VD = +3.0V fSCLK = 0 ksps 0.06 W VA = VD = +5.0V fSCLK = 0 ksps 0.25 W Data sheet min/max specification limits are ensured by design, test, or statistical analysis. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 5 ADC128S102 SNAS298F - AUGUST 2005 - REVISED MAY 2013 www.ti.com ADC128S102 Converter Electrical Characteristics (1) (continued) The following specifications apply for AGND = DGND = 0V, fSCLK = 8 MHz to 16 MHz, fSAMPLE = 500 ksps to 1 MSPS, CL = 50pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25C. Parameter Test Conditions Typical Limits (2) Units AC ELECTRICAL CHARACTERISTICS fSCLKMIN Minimum Clock Frequency VA = VD = +2.7V to +5.25V fSCLK Maximum Clock Frequency VA = VD = +2.7V to +5.25V fS Sample Rate Continuous Mode VA = VD = +2.7V to +5.25V tCONVERT Conversion (Hold) Time VA = VD = +2.7V to +5.25V 0.8 50 8 MHz (min) 16 MHz (max) 500 ksps (min) 1 MSPS (max) 13 SCLK cycles 30 40 % (min) 70 DC SCLK Duty Cycle VA = VD = +2.7V to +5.25V 60 % (max) tACQ Acquisition (Track) Time VA = VD = +2.7V to +5.25V 3 SCLK cycles Throughput Time Acquisition Time + Conversion Time VA = VD = +2.7V to +5.25V 16 SCLK cycles Aperture Delay VA = VD = +2.7V to +5.25V tAD 4 ns ADC128S102 Timing Specifications The following specifications apply for VA = VD = +2.7V to +5.25V, AGND = DGND = 0V, fSCLK = 8 MHz to 16 MHz, fSAMPLE = 500 ksps to 1 MSPS, and CL = 50pF. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25C. Parameter Test Conditions tCSH CS Hold Time after SCLK Rising Edge tCSS CS Setup Time prior to SCLK Rising Edge tEN Typical Limits (1) Units ns (min) 0 10 4.5 10 ns (min) CS Falling Edge to DOUT enabled 5 30 ns (max) tDACC DOUT Access Time after SCLK Falling Edge 17 27 ns (max) tDHLD DOUT Hold Time after SCLK Falling Edge 4 tDS DIN Setup Time prior to SCLK Rising Edge 3 10 ns (min) tDH DIN Hold Time after SCLK Rising Edge 3 10 ns (min) tCH SCLK High Time 0.4 x tSCLK ns (min) tCL SCLK Low Time 0.4 x tSCLK ns (min) tDIS CS Rising Edge to DOUT High-Impedance (1) 6 ns (typ) DOUT falling 2.4 20 ns (max) DOUT rising 0.9 20 ns (max) Tested limits are specified to TI's AOQL (Average Outgoing Quality Level). Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 ADC128S102 www.ti.com SNAS298F - AUGUST 2005 - REVISED MAY 2013 TIMING DIAGRAMS Power Down Power Up Track Power Up Hold Track Hold CS 1 2 3 4 5 6 8 7 9 10 11 12 13 14 15 1 16 2 3 4 5 6 7 8 SCLK Control register DIN DOUT ADD2 ADD1 ADD0 ADD2 ADD1 DB11 DB10 DB9 FOUR ZEROS DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 FOUR ZEROS DB0 ADD0 DB11 DB10 DB9 Figure 2. ADC128S102 Operational Timing Diagram CS tCONVERT tACQ tCH SCLK 1 2 3 4 5 6 7 tCL tEN DOUT 8 16 tDACC DB11 FOUR ZEROS DB10 tDHLD DB9 DB8 tDIS DB1 DB0 tDH tDS DIN DONTC DONTC ADD2 ADD1 ADD0 DONTC DONTC DONTC Figure 3. ADC128S102 Serial Timing Diagram SCLK tCSS CS tCSH CS Figure 4. SCLK and CS Timing Parameters Specification Definitions ACQUISITION TIME is the time required for the ADC to acquire the input voltage. During this time, the hold capacitor is charged by the input voltage. APERTURE DELAY is the time between the fourth falling edge of SCLK and the time when the input signal is internally acquired or held for conversion. CONVERSION TIME is the time required, after the input voltage is acquired, for the ADC to convert the input voltage to a digital word. CHANNEL-TO-CHANNEL ISOLATION is resistance to coupling of energy from one channel into another channel. CROSSTALK is the coupling of energy from one channel into another channel. This is similar to Channel-toChannel Isolation, except for the sign of the data. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 7 ADC128S102 SNAS298F - AUGUST 2005 - REVISED MAY 2013 www.ti.com DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB. DUTY CYCLE is the ratio of the time that a repetitive digital waveform is high to the total time of one period. The specification here refers to the SCLK. EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise and Distortion or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is equivalent to a perfect ADC of this (ENOB) number of bits. FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental drops 3 dB below its low frequency value for a full scale input. FULL SCALE ERROR (FSE) is a measure of how far the last code transition is from the ideal 11/2 LSB below VREF+ and is defined as: (1) VFSE = Vmax + 1.5 LSB - VREF+ where Vmax is the voltage at which the transition to the maximum code occurs. FSE can be expressed in Volts, LSB or percent of full scale range. GAIN ERROR is the deviation of the last code transition (111...110) to (111...111) from the ideal (VREF - 1.5 LSB), after adjusting for offset error. INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from negative full scale (1/2 LSB below the first code transition) through positive full scale (1/2 LSB above the last code transition). The deviation of any given code from this straight line is measured from the center of that code value. INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two sinusoidal frequencies being applied to an individual ADC input at the same time. It is defined as the ratio of the power in both the second or the third order intermodulation products to the power in one of the original frequencies. Second order products are fa fb, where fa and fb are the two sine wave input frequencies. Third order products are (2fa fb ) and (fa 2fb). IMD is usually expressed in dB. MISSING CODES are those output codes that will never appear at the ADC outputs. These codes cannot be reached with any input value. The ADC128S102 is ensured not to have any missing codes. OFFSET ERROR is the deviation of the first code transition (000...000) to (000...001) from the ideal (i.e. GND + 0.5 LSB). SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms value of the sum of all other spectral components below one-half the sampling frequency, not including d.c. or the harmonics included in THD. SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the input signal to the rms value of all of the other spectral components below half the clock frequency, including harmonics but excluding d.c. SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the desired signal amplitude to the amplitude of the peak spurious spectral component, where a spurious spectral component is any signal present in the output spectrum that is not present at the input and may or may not be a harmonic. TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dBc, of the rms total of the first five harmonic components at the output to the rms level of the input signal frequency as seen at the output. THD is calculated as: THD = 20 log 10 A f22 + + A f10 2 A f12 (2) where Af1 is the RMS power of the input frequency at the output and Af2 through Af10 are the RMS power in the first 9 harmonic frequencies. THROUGHPUT TIME is the minimum time required between the start of two successive conversions. It is the acquisition time plus the conversion and read out times. In the case of the ADC128S102, this is 16 SCLK periods. 8 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 ADC128S102 www.ti.com SNAS298F - AUGUST 2005 - REVISED MAY 2013 Typical Performance Characteristics TA = +25C, fSAMPLE = 1 MSPS, fSCLK = 16 MHz, fIN = 40.2 kHz unless otherwise stated. DNL DNL Figure 5. Figure 6. INL INL Figure 7. Figure 8. DNL vs. Supply INL vs. Supply Figure 9. Figure 10. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 9 ADC128S102 SNAS298F - AUGUST 2005 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) TA = +25C, fSAMPLE = 1 MSPS, fSCLK = 16 MHz, fIN = 40.2 kHz unless otherwise stated. 10 SNR vs. Supply THD vs. Supply Figure 11. Figure 12. ENOB vs. Supply DNL vs. VD with VA = 5.0 V Figure 13. Figure 14. INL vs. VD with VA = 5.0 V DNL vs. SCLK Duty Cycle Figure 15. Figure 16. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 ADC128S102 www.ti.com SNAS298F - AUGUST 2005 - REVISED MAY 2013 Typical Performance Characteristics (continued) TA = +25C, fSAMPLE = 1 MSPS, fSCLK = 16 MHz, fIN = 40.2 kHz unless otherwise stated. INL vs. SCLK Duty Cycle SNR vs. SCLK Duty Cycle Figure 17. Figure 18. THD vs. SCLK Duty Cycle ENOB vs. SCLK Duty Cycle Figure 19. Figure 20. DNL vs. SCLK INL vs. SCLK Figure 21. Figure 22. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 11 ADC128S102 SNAS298F - AUGUST 2005 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) TA = +25C, fSAMPLE = 1 MSPS, fSCLK = 16 MHz, fIN = 40.2 kHz unless otherwise stated. 12 SNR vs. SCLK THD vs. SCLK Figure 23. Figure 24. ENOB vs. SCLK DNL vs. Temperature Figure 25. Figure 26. INL vs. Temperature SNR vs. Temperature Figure 27. Figure 28. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 ADC128S102 www.ti.com SNAS298F - AUGUST 2005 - REVISED MAY 2013 Typical Performance Characteristics (continued) TA = +25C, fSAMPLE = 1 MSPS, fSCLK = 16 MHz, fIN = 40.2 kHz unless otherwise stated. THD vs. Temperature ENOB vs. Temperature Figure 29. Figure 30. SNR vs. Input Frequency THD vs. Input Frequency Figure 31. Figure 32. ENOB vs. Input Frequency Power Consumption vs. SCLK Figure 33. Figure 34. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 13 ADC128S102 SNAS298F - AUGUST 2005 - REVISED MAY 2013 www.ti.com FUNCTIONAL DESCRIPTION The ADC128S102 is a successive-approximation analog-to-digital converter designed around a chargeredistribution digital-to-analog converter. ADC128S102 OPERATION Simplified schematics of the ADC128S102 in both track and hold operation are shown in Figure 35 and Figure 36 respectively. In Figure 35, the ADC128S102 is in track mode: switch SW1 connects the sampling capacitor to one of eight analog input channels through the multiplexer, and SW2 balances the comparator inputs. The ADC128S102 is in this state for the first three SCLK cycles after CS is brought low. Figure 36 shows the ADC128S102 in hold mode: switch SW1 connects the sampling capacitor to ground, maintaining the sampled voltage, and switch SW2 unbalances the comparator. The control logic then instructs the charge-redistribution DAC to add or subtract fixed amounts of charge to or from the sampling capacitor until the comparator is balanced. When the comparator is balanced, the digital word supplied to the DAC is the digital representation of the analog input voltage. The ADC128S102 is in this state for the last thirteen SCLK cycles after CS is brought low. IN0 CHARGE REDISTRIBUTION DAC MUX SAMPLING CAPACITOR SW1 IN7 SW2 CONTRO L LOGI C + - AGND VA /2 Figure 35. ADC128S102 in Track Mode IN0 CHARGE REDISTRIBUTION DAC MUX IN7 SAMPLING CAPACITOR + SW1 SW2 CONTROL LOGIC - AGND VA /2 Figure 36. ADC128S102 in Hold Mode SERIAL INTERFACE An operational timing diagram and a serial interface timing diagram for the ADC128S102 are shown in the Timing Diagrams section. CS, chip select, initiates conversions and frames the serial data transfers. SCLK (serial clock) controls both the conversion process and the timing of serial data. DOUT is the serial data output pin, where a conversion result is sent as a serial data stream, MSB first. Data to be written to the ADC128S102's Control Register is placed on DIN, the serial data input pin. New data is written to DIN with each conversion. A serial frame is initiated on the falling edge of CS and ends on the rising edge of CS. Each frame must contain an integer multiple of 16 rising SCLK edges. The ADC's DOUT pin is in a high impedance state when CS is high and is active when CS is low. Thus, CS acts as an output enable. Similarly, SCLK is internally gated off when CS is brought high. 14 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 ADC128S102 www.ti.com SNAS298F - AUGUST 2005 - REVISED MAY 2013 During the first 3 cycles of SCLK, the ADC is in the track mode, acquiring the input voltage. For the next 13 SCLK cycles the conversion is accomplished and the data is clocked out. SCLK falling edges 1 through 4 clock out leading zeros while falling edges 5 through 16 clock out the conversion result, MSB first. If there is more than one conversion in a frame (continuous conversion mode), the ADC will re-enter the track mode on the falling edge of SCLK after the N*16th rising edge of SCLK and re-enter the hold/convert mode on the N*16+4th falling edge of SCLK. "N" is an integer value. The ADC128S102 enters track mode under three different conditions. In Figure 2, CS goes low with SCLK high and the ADC enters track mode on the first falling edge of SCLK. In the second condition, CS goes low with SCLK low. Under this condition, the ADC automatically enters track mode and the falling edge of CS is seen as the first falling edge of SCLK. In the third condition, CS and SCLK go low simultaneously and the ADC enters track mode. While there is no timing restriction with respect to the rising edges of CS and SCLK, see Figure 4 for setup and hold time requirements for the falling edge of CS with respect to the rising edge of SCLK. While a conversion is in progress, the address of the next input for conversion is clocked into a control register through the DIN pin on the first 8 rising edges of SCLK after the fall of CS. See Table 1, Table 2, and Table 3. There is no need to incorporate a power-up delay or dummy conversions as the ADC128S102 is able to acquire the input signal to full resolution in the first conversion immediately following power-up. The first conversion result after power-up will be that of IN0. Table 1. Control Register Bits Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 DONTC DONTC ADD2 ADD1 ADD0 DONTC DONTC DONTC Table 2. Control Register Bit Descriptions Bit No: Symbol: 7, 6, 2, 1, 0 DONTC 5 ADD2 4 ADD1 3 ADD0 Description Don't care. The values of these bits do not affect the device. These three bits determine which input channel will be sampled and converted at the next conversion cycle. The mapping between codes and channels is shown in Table 3. Table 3. Input Channel Selection ADD2 ADD1 ADD0 Input Channel 0 0 0 IN0 (Default) 0 0 1 IN1 0 1 0 IN2 0 1 1 IN3 1 0 0 IN4 1 0 1 IN5 1 1 0 IN6 1 1 1 IN7 ADC128S102 TRANSFER FUNCTION The output format of the ADC128S102 is straight binary. Code transitions occur midway between successive integer LSB values. The LSB width for the ADC128S102 is VA / 4096. The ideal transfer characteristic is shown in Figure 37. The transition from an output code of 0000 0000 0000 to a code of 0000 0000 0001 is at 1/2 LSB, or a voltage of VA / 8192. Other code transitions occur at steps of one LSB. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 15 ADC128S102 SNAS298F - AUGUST 2005 - REVISED MAY 2013 www.ti.com 111...111 111...000 | | ADC CODE 111...110 1LSB = VA/4096 011...111 000...010 | 000...001 000...000 0V 0.5LSB ANALOG INPUT +VA - 1.5LSB Figure 37. Ideal Transfer Characteristic ANALOG INPUTS An equivalent circuit for one of the ADC128S102's input channels is shown in Figure 38. Diodes D1 and D2 provide ESD protection for the analog inputs. The operating range for the analog inputs is 0 V to VA. Going beyond this range will cause the ESD diodes to conduct and result in erratic operation. The capacitor C1 in Figure 38 has a typical value of 3 pF and is mainly the package pin capacitance. Resistor R1 is the on resistance of the multiplexer and track / hold switch and is typically 500 ohms. Capacitor C2 is the ADC128S102 sampling capacitor, and is typically 30 pF. The ADC128S102 will deliver best performance when driven by a low-impedance source (less than 100 ohms). This is especially important when using the ADC128S102 to sample dynamic signals. Also important when sampling dynamic signals is a band-pass or lowpass filter which reduces harmonics and noise in the input. These filters are often referred to as anti-aliasing filters. VA D1 R1 C2 30 pF VIN C1 3 pF D2 Conversion Phase - Switch Open Track Phase - Switch Closed Figure 38. Equivalent Input Circuit DIGITAL INPUTS AND OUTPUTS The ADC128S102's digital inputs (SCLK, CS, and DIN) have an operating range of 0 V to VA. They are not prone to latch-up and may be asserted before the digital supply (VD) without any risk. The digital output (DOUT) operating range is controlled by VD. The output high voltage is VD - 0.5V (min) while the output low voltage is 0.4V (max). 16 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 ADC128S102 www.ti.com SNAS298F - AUGUST 2005 - REVISED MAY 2013 Applications Information TYPICAL APPLICATION CIRCUIT A typical application is shown in Figure 39. The split analog and digital supply pins are both powered in this example by the TI LP2950 low-dropout voltage regulator. The analog supply is bypassed with a capacitor network located close to the ADC128S102. The digital supply is separated from the analog supply by an isolation resistor and bypassed with additional capacitors. The ADC128S102 uses the analog supply (VA) as its reference voltage, so it is very important that VA be kept as clean as possible. Due to the low power requirements of the ADC128S102, it is also possible to use a precision reference as a power supply. 51: LP2950 0.1 PF VD 22: INPUT 0.1 PF 1.0 PF 1 nF . . . 1.0 PF VA IN0 ADC128S102 0.1 PF 1 PF SCLK CS DIN IN7 5V MICROPROCESSOR DSP DOUT AGND DGND Figure 39. Typical Application Circuit POWER SUPPLY CONSIDERATIONS There are three major power supply concerns with this product: power supply sequencing, power management, and the effect of digital supply noise on the analog supply. Power Supply Sequence The ADC128S102 is a dual-supply device. The two supply pins share ESD resources, so care must be exercised to ensure that the power is applied in the correct sequence. To avoid turning on the ESD diodes, the digital supply (VD) cannot exceed the analog supply (VA) by more than 300 mV. Therefore, VA must ramp up before or concurrently with VD. Power Management The ADC128S102 is fully powered-up whenever CS is low and fully powered-down whenever CS is high, with one exception. If operating in continuous conversion mode, the ADC128S102 automatically enters power-down mode between SCLK's 16th falling edge of a conversion and SCLK's 1st falling edge of the subsequent conversion (see Figure 2). In continuous conversion mode, the ADC128S102 can perform multiple conversions back to back. Each conversion requires 16 SCLK cycles and the ADC128S102 will perform conversions continuously as long as CS is held low. Continuous mode offers maximum throughput. In burst mode, the user may trade off throughput for power consumption by performing fewer conversions per unit time. This means spending more time in power-down mode and less time in normal mode. By utilizing this technique, the user can achieve very low sample rates while still utilizing an SCLK frequency within the electrical specifications. The Power Consumption vs. SCLK curve in the Typical Performance Characteristics section shows the typical power consumption of the ADC128S102. To calculate the power consumption (PC), simply multiply the fraction of time spent in the normal mode (tN) by the normal mode power consumption (PN), and add the fraction of time spent in shutdown mode (tS) multiplied by the shutdown mode power consumption (PS) as shown in Equation 3. PC = tS tN x PN + x PS tN + t S tN + t S (3) Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 17 ADC128S102 SNAS298F - AUGUST 2005 - REVISED MAY 2013 www.ti.com Power Supply Noise Considerations The charging of any output load capacitance requires current from the digital supply, VD. The current pulses required from the supply to charge the output capacitance will cause voltage variations on the digital supply. If these variations are large enough, they could degrade SNR and SINAD performance of the ADC. Furthermore, if the analog and digital supplies are tied directly together, the noise on the digital supply will be coupled directly into the analog supply, causing greater performance degradation than would noise on the digital supply alone. Similarly, discharging the output capacitance when the digital output goes from a logic high to a logic low will dump current into the die substrate, which is resistive. Load discharge currents will cause "ground bounce" noise in the substrate that will degrade noise performance if that current is large enough. The larger the output capacitance, the more current flows through the die substrate and the greater the noise coupled into the analog channel. The first solution to keeping digital noise out of the analog supply is to decouple the analog and digital supplies from each other or use separate supplies for them. To keep noise out of the digital supply, keep the output load capacitance as small as practical. If the load capacitance is greater than 50 pF, use a 100 series resistor at the ADC output, located as close to the ADC output pin as practical. This will limit the charge and discharge current of the output capacitance and improve noise performance. Since the series resistor and the load capacitance form a low frequency pole, verify signal integrity once the series resistor has been added. LAYOUT AND GROUNDING Capacitive coupling between the noisy digital circuitry and the sensitive analog circuitry can lead to poor performance. The solution is to keep the analog circuitry separated from the digital circuitry and the clock line as short as possible. Digital circuits create substantial supply and ground current transients. The logic noise generated could have significant impact upon system noise performance. To avoid performance degradation of the ADC128S102 due to supply noise, do not use the same supply for the ADC128S102 that is used for digital logic. Generally, analog and digital lines should cross each other at 90 to avoid crosstalk. However, to maximize accuracy in high resolution systems, avoid crossing analog and digital lines altogether. It is important to keep clock lines as short as possible and isolated from ALL other lines, including other digital lines. In addition, the clock line should also be treated as a transmission line and be properly terminated. The analog input should be isolated from noisy signal traces to avoid coupling of spurious signals into the input. Any external component (e.g., a filter capacitor) connected between the converter's input pins and ground or to the reference input pin and ground should be connected to a very clean point in the ground plane. We recommend the use of a single, uniform ground plane and the use of split power planes. The power planes should be located within the same board layer. All analog circuitry (input amplifiers, filters, reference components, etc.) should be placed over the analog power plane. All digital circuitry and I/O lines should be placed over the digital power plane. Furthermore, all components in the reference circuitry and the input signal chain that are connected to ground should be connected together with short traces and enter the analog ground plane at a single, quiet point. 18 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 ADC128S102 www.ti.com SNAS298F - AUGUST 2005 - REVISED MAY 2013 REVISION HISTORY Changes from Revision D (March 2013) to Revision E * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 18 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: ADC128S102 19 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) ADC128S102CIMT NRND TSSOP PW 16 92 TBD Call TI Call TI -40 to 105 128S102 CIMT ADC128S102CIMT/NOPB ACTIVE TSSOP PW 16 92 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 128S102 CIMT ADC128S102CIMTX/NOPB ACTIVE TSSOP PW 16 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 128S102 CIMT (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device ADC128S102CIMTX/NOP B Package Package Pins Type Drawing TSSOP PW 16 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 6.95 B0 (mm) K0 (mm) P1 (mm) 8.3 1.6 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 *All dimensions are nominal Device ADC128S102CIMTX/NOP B Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TSSOP PW 16 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated