KAI-04070 2048 (H) x 2048 (V) Interline CCD Image Sensor Description The KAI-04070 Image Sensor is a 4-megapixel CCD in a 4/3 inch optical format. Based on the TRUESENSE 7.4 micron Interline Transfer CCD Platform, the sensor provides very high smear rejection and up to 82 dB linear dynamic range through the use of a unique dual-gain amplifier. A flexible readout architecture enables use of 1, 2, or 4 outputs for full resolution readout up to 28 frames per second, while a vertical overflow drain structure suppresses image blooming and enables electronic shuttering for precise exposure control. www.onsemi.com Table 1. GENERAL SPECIFICATIONS Parameter Typical Value Architecture Interline CCD, Progressive Scan Total Number of Pixels 2128 (H) x 2112 (V) Number of Effective Pixels 2080 (H) x 2080 (V) Number of Active Pixels 2048 (H) x 2048 (V) Pixel Size 7.4 mm (H) x 7.4 mm (V) Active Image Size 15.2 mm (H) x 15.2 mm (V), 21.4 mm (Diagonal), 4/3 Optical Format Aspect Ratio 1:1 Number of Outputs 1, 2, or 4 Charge Capacity 44,000 electrons Output Sensitivity 8.7 mV/e- (Low), 33 mV/e- (High) Quantum Efficiency Pan (-ABA, -PBA, -QBA) R, G, B (-CBA) R, G, B (-FBA) 52% 38%, 42%, 43% 37%, 42%, 41% Read Noise (f = 40 MHz) 12 e- rms Dark Current Photodiode VCCD 3 e-/s 145 e-/s Dark Current Doubling Temp. Photodiode VCCD 7C 9C Dynamic Range High Gain Amp (40 MHz) Dual Amp, 2x2 Bin (40 MHz) 70 dB 82 dB Charge Transfer Efficiency 0.999999 Blooming Suppression > 1000 X Smear -115 dB Image Lag < 10 electrons Maximum Pixel Clock Speed 40 MHz Maximum Frame Rate Quad Output Dual Output Single Output 28 fps 14 fps 8 fps Package 68 Pin PGA Cover Glass AR Coated, 2 Sides Figure 1. KAI-04070 Interline CCD Image Sensor Features * Superior Smear Rejection * Up to 82 dB Linear Dynamic Range * Bayer Color Pattern, TRUESENSE Sparse * * * * Color Filter Pattern, and Monochrome Configurations Progressive Scan & Flexible Readout Architecture High Frame Rate High Sensitivity - Low Noise Architecture Package Pin Reserved for Device Identification Application * Industrial Imaging and Inspection * Traffic * Surveillance ORDERING INFORMATION See detailed ordering and shipping information on page 2 of this data sheet. NOTE: All Parameters are specified at T = 40C unless otherwise noted. (c) Semiconductor Components Industries, LLC, 2015 July, 2015 - Rev. 3 1 Publication Order Number: KAI-04070/D KAI-04070 The sensor is available with the TRUESENSE Sparse Color Filter Pattern, a technology which provides a 2x improvement in light sensitivity compared to a standard color Bayer part. The sensor shares common pin-out and electrical configurations with a full family of Truesense Imaging Interline Transfer CCD image sensors, allowing a single camera design to be leveraged in support of multiple devices. ORDERING INFORMATION Table 2. ORDERING INFORMATION - KAI-04070 IMAGE SENSOR Part Number Description Marking Code KAI-04070-ABA-JD-BA Monochrome, Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI-04070-ABA-JD-AE Monochrome, Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade KAI-04070-ABA-JR-BA Monochrome, Telecentric Microlens, PGA Package, Taped Clear Cover Glass with AR Coating (Both Sides), Standard Grade KAI-04070-ABA-JR-AE Monochrome, Telecentric Microlens, PGA Package, Taped Clear Cover Glass with AR Coating (Both Sides), Engineering Grade 11KAI-04070-FBA-JD-BA Gen2 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade 11KAI-04070-FBA-JD-AE Gen2 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade 11KAI-04070-QBA-JD-BA Gen2 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade 11KAI-04070-QBA-JD-AE Gen2 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade 11KAI-04070-CBA-JD-BA* Gen1 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade 11KAI-04070-CBA-JD-AE* Gen1 Color (Bayer RGB), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade 11KAI-04070-PBA-JD-BA* Gen1 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Standard Grade 11KAI-04070-PBA-JD-AE* Gen1 Color (TRUESENSE Sparse CFA), Telecentric Microlens, PGA Package, Sealed Clear Cover Glass with AR Coating (Both Sides), Engineering Grade KAI-04070-ABA Serial Number KAI-04070-FBA Serial Number KAI-04070-QBA Serial Number KAI-04070-CBA Serial Number KAI-04070-PBA Serial Number *Note recommended for new designs. Table 3. ORDERING INFORMATION - EVALUATION SUPPORT Part Number Description G2-FPGA-BD-14-40-A-GEVK FPGA Board for IT-CCD Evaluation Hardware KAI-68PIN-HEAD-BD-A-GEVB 68 Pin Imager Board for IT-CCD Evaluation Hardware LENS-MOUNT-KIT-A-GEVK Lens Mount Kit for IT-CCD Evaluation Hardware KAI-68PIN-N-PROBE-CARD-A-GEVB 68 Pin Probe Card (Narrow Socket) KAI-68PIN-W-PROBE-CARD-A-GEVB 68 Pin Probe Card (Wide Socket) See the ON Semiconductor Device Nomenclature document (TND310/D) for a full description of the naming convention used for image sensors. For reference documentation, including information on evaluation kits, please visit our web site at www.onsemi.com. www.onsemi.com 2 KAI-04070 DEVICE DESCRIPTION Architecture R2cd RDcd H2B d H2S d H1B d H1S d SUB H2B c H2S c H1B c H1S c RDcd NNNNNNNNNNNNNNNNNN IIIIIIIIIIIIIIII IIIIIIIIIIIIIIII R1c HLOD VDDc VOUTc 1 11 24 16 1024 1024 16 8 24 11 1 1 Dummy 16 16 GND OGc H2SLc R2cd R1d VDDd VOUTd GND OGd H2 SLd V1T V2T V3T V4T V1T V2T V3T V4T DevID ESD 2048H x 2048V 7.4mm x 7.4mm Pixels 24 16 16 24 V1B V2B V3B V4B RDab R2ab R1 a VDDa VOUTa ESD V1B V2B V3B V4B IIIIIIIIIIIIIIII IIIIIIIIIIIIIIII NNNNNNNNNNNNNNNNNN 16 Buffer 16 Dark 1 Dummy (Last VCCD Phase = V1 a H1S) 1 11 24 16 8 1024 1024 16 8 24 11 1 RDab R2ab R1b VDDb VOUTb HLOD H2Bb H2Sb H1Bb H1Sb SUB H2Ba H2Sa H1Ba H1Sa GND OGa H2SLa GND OGb H2SLb Figure 2. Block Diagram Dark Reference Pixels Image Acquisition There are 16 dark reference rows at the top and 16 dark rows at the bottom of the image sensor. The 24 dark columns on the left or right side of the image sensor should be used as a dark reference. Under normal circumstances use only the center 22 columns of the 24 column dark reference due to potential light leakage. An electronic representation of an image is formed when incident photons falling on the sensor plane create electron-hole pairs within the individual silicon photodiodes. These photoelectrons are collected locally by the formation of potential wells at each photosite. Below photodiode saturation, the number of photoelectrons collected at each pixel is linearly dependent upon light level and exposure time and non-linearly dependent on wavelength. When the photodiodes charge capacity is reached, excess electrons are discharged into the substrate to prevent blooming. Dummy Pixels Within each horizontal shift register there are 12 leading additional shift phases. These pixels are designated as dummy pixels and should not be used to determine a dark reference level. In addition, there is one dummy row of pixels at the top and bottom of the image. ESD Protection Adherence to the power-up and power-down sequence is critical. Failure to follow the proper power-up and power-down sequences may cause damage to the sensor. See Power-Up and Power-Down Sequence section. Active Buffer Pixels 16 unshielded pixels adjacent to any leading or trailing dark reference regions are classified as active buffer pixels. These pixels are light sensitive but are not tested for defects and non-uniformities. www.onsemi.com 3 KAI-04070 Bayer Color Filter Pattern RDcd R2cd R1d VDDd VOUTd H2Bd H2Sd H1Bd H1Sd SUB GND OGc H2SLc H2Bc H2Sc H1Bc H1Sc RDcd R2cd R1c VDDc VOUTc NNNNNNNNNNNNNNN IIIIIIIIIIIIII IIIIIIIIIIIIII HLOD 1 11 24 16 1024 1024 16 8 24 11 1 1Dummy 16 16 B G G R V1T V2T V3T V4T B G G R GND OGd H2SLd V1T V2T V3T V4T DevID ESD V1B V2B V3B V4B RDab R2ab R1a VDDa VOUTa 2048 (H) x 2048 (V) 7.4 mm x 7.4 mm Pixels 24 16 16 24 B G G R ESD B G G R IIIIIIIIIIIIII IIIIIIIIIIIIII NNNNNNNNNNNNNN V1B V2B V3B V4B RDab R2ab R1b VDDb VOUTb 16 Buffer 16 Dark 1 Dummy (Last VCCD Phase = V1 H1S) 1 11 24 16 8 1024 1024 16 8 24 11 1 HLOD GND OGb H2SLb H2Bb H2Sb H1Bb H1Sb SUB H2Ba H2Sa H1Ba H1Sa GND OGa H2SLa Figure 3. Bayer Color Filter Pattern TRUESENSE Sparse Color Filter Pattern RDcd R2cd R1d VDDd VOUTd H2Bd H2Sd H1Bd H1Sd SUB GND OGc H2SLc H2Bc H2Sc H1Bc H1Sc RDcd R2cd R1c VDDc VOUTc NNNNNNNNNNNNNNN IIIIIIIIIIIIII IIIIIIIIIIIIII HLOD 1 11 24 16 1024 1024 16 8 24 11 1 1 Dummy 16 16 G P B P V1T V2T V3T V4T P G P B R P G P G P B P P R P G P G P B R P G P P R P G GND OGd H2SLd V1T V2T V3T V4T DevID ESD V1B V2B V3B V4B RDab R2ab R1a VDDa VOUTa G P B P P G P B R P G P 16 24 G P B P P R P G P G P B R P G P ESD V1B V2B V3B V4B P R P G IIIIIIIIIIIIII NNNNNNNNNNNNNNN NNNNNNNNNNNNNNN 16 Buffer 16 Dark 1 Dummy (Last VCCD Phase = V1 H1S) 1 11 24 16 8 1024 1024 16 8 24 11 1 HLOD H2Bb H2Sb H1Bb H1Sb SUB H2Ba H2Sa H1Ba H1Sa GND OGa H2SLa 2048 (H) x 2048 (V) 7.4 mm x 7.4 mm Pixels 24 16 Figure 4. TRUESENSE Sparse Color Filter Pattern www.onsemi.com 4 RDab R2ab R1b VDDb VOUTb GND OGb H2SLb KAI-04070 Physical Description Pin Description and Device Orientation H2Sc R2cd H2Sd H1Bd H2SLd Rd GND VDDd V1T V3T 57 55 53 51 49 47 45 43 41 39 37 35 VOUTc RDcd OGc H2Bc H1Sc SUB H1Sd H2Bd OGd 62 58 56 54 52 50 48 46 V3T V1T VDDc GND Rc 67 65 63 61 59 ESD V4T V2T 68 64 66 60 H2SLc H1Bc RDcd VOUTd 44 42 26 28 V2T 40 V4T DevID 38 36 32 34 Pixel (1,1) 4 V4B 6 V2B 8 10 VOUTa RDab 1 3 5 7 9 V3B V1B VDDa GND Ra 12 14 16 18 20 22 24 OGa H2Ba H1Sa SUB H1Sb H2Bb OGb 11 13 15 17 19 21 23 25 27 29 31 33 H2Sa R2ab H2Sb H1Bb H2SLb Rb GND VDDb V1B V3B H2SLa H1Ba RDab VOUTb 30 V2B V4B ESD Figure 5. Package Pin Designations - Top View Table 4. PACKAGE PIN DESCRIPTION Pin Name Description 1 V3B Vertical CCD Clock, Phase 3, Bottom 3 V1B Vertical CCD Clock, Phase 1, Bottom 4 V4B Vertical CCD Clock, Phase 4, Bottom 5 VDDa Output Amplifier Supply, Quadrant a 6 V2B Vertical CCD Clock, Phase 2, Bottom 7 GND Ground 8 VOUTa 9 Ra Video Output, Quadrant a Reset Gate, Standard (High) Gain, Quadrant a 10 RDab Reset Drain, Quadrants a & b 11 H2SLa Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant a 12 OGa Output Gate, Quadrant a 13 H1Ba Horizontal CCD Clock, Phase 1, Barrier, Quadrant a 14 H2Ba Horizontal CCD Clock, Phase 2, Barrier, Quadrant a 15 H2Sa Horizontal CCD Clock, Phase 2, Storage, Quadrant a 16 H1Sa Horizontal CCD Clock, Phase 1, Storage, Quadrant a 17 R2ab Reset Gate, Low Gain, Quadrants a & b 18 SUB Substrate 19 H2Sb Horizontal CCD Clock, Phase 2, Storage, Quadrant b 20 H1Sb Horizontal CCD Clock, Phase 1, Storage, Quadrant b 21 H1Bb Horizontal CCD Clock, Phase 1, Barrier, Quadrant b www.onsemi.com 5 KAI-04070 Table 4. PACKAGE PIN DESCRIPTION (continued) Pin Name Description 22 H2Bb Horizontal CCD Clock, Phase 2, Barrier, Quadrant b 23 H2SLb Horizontal CCD Clock, Phase 1, Storage, Last Phase, Quadrant b 24 OGb 25 Rb 26 RDab Reset Drain, Quadrants a & b 27 GND Ground 28 VOUTb 29 VDDb Output Amplifier Supply, Quadrant b 30 V2B Vertical CCD Clock, Phase 2, Bottom 31 V1B Vertical CCD Clock, Phase 1, Bottom 32 V4B Vertical CCD Clock, Phase 4, Bottom 33 V3B Vertical CCD Clock, Phase 3, Bottom 34 ESD ESD Protection Disable 35 V3T Vertical CCD Clock, Phase 3, Top 36 DevID 37 V1T Vertical CCD Clock, Phase 1, Top 38 V4T Vertical CCD Clock, Phase 4, Top 39 VDDd Output Gate, Quadrant b Reset Gate, Standard (High) Gain, Quadrant b Video Output, Quadrant b Device Identification Output Amplifier Supply, Quadrant d 40 V2T Vertical CCD Clock, Phase 2, Top 41 GND Ground 42 VOUTd Video Output, Quadrant d 43 Rd 44 RDcd Reset Gate, Standard (High) Gain, Quadrant d Reset Drain, Quadrants c & d 45 H2SLd Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant d 46 OGd Output Gate, Quadrant d 47 H1Bd Horizontal CCD Clock, Phase 1, Barrier, Quadrant d 48 H2Bd Horizontal CCD Clock, Phase 2, Barrier, Quadrant d 49 H2Sd Horizontal CCD Clock, Phase 2, Storage, Quadrant d 50 H1Sd Horizontal CCD Clock, Phase 1, Storage, Quadrant d 51 R2cd Reset Gate, Low Gain, Quadrants c & d 52 SUB Substrate 53 H2Sc Horizontal CCD Clock, Phase 2, Storage, Quadrant c 54 H1Sc Horizontal CCD Clock, Phase 1, Storage, Quadrant c 55 H1Bc Horizontal CCD Clock, Phase 1, Barrier, Quadrant c 56 H2Bc Horizontal CCD Clock, Phase 2, Barrier, Quadrant c 57 H2SLc Horizontal CCD Clock, Phase 2, Storage, Last Phase, Quadrant c 58 OGc 59 Rc 60 RDcd Reset Drain, Quadrants c & d 61 GND Ground 62 VOUTc Video Output, Quadrant c 63 VDDc Output Amplifier Supply, Quadrant c 64 V2T Vertical CCD Clock, Phase 2, Top 65 V1T Vertical CCD Clock, Phase 1, Top 66 V4T Vertical CCD Clock, Phase 4, Top 67 V3T Vertical CCD Clock, Phase 3, Top 68 ESD EDS Protection Disable Output Gate, Quadrant c Reset Gate, Standard (High) Gain, Quadrant c 1. Liked named pins are internally connected and should have a common drive signal. www.onsemi.com 6 KAI-04070 IMAGING PERFORMANCE Table 5. TYPICAL OPERATIONAL CONDITIONS (Unless otherwise noted, the Imaging Performance Specifications are measured using the following conditions.) Condition Description Light Source Continuous Red, Green and Blue LED Illumination Operation Nominal Operating Voltages and Timing Notes 1 1. For monochrome sensor, only green LED used. Specifications Table 6. PERFORMANCE SPECIFICATIONS Temperature Tested at (5C) Symbol Min. Nom. Max. Unit Sampling Plan DSNU - - 2.0 mVpp Die 27, 40 - 2.0 5.0 % rms Die 27, 40 - 5.0 15.0 % pp Die 27, 40 - 1.0 2.0 % rms Die 27, 40 % Design NL_HG1 NL_HG2 NL_LG1 - - - 2 3 6 - - - Maximum Gain Difference between Outputs (Note 2) DG - - 10 % Design Horizontal CCD Charge Capacity HNe - 90 - ke- Design Vertical CCD Charge Capacity VNe - 60 - ke- Design Description ALL CONFIGURATIONS Dark Field Global Non-Uniformity Bright Field Global Non-Uniformity (Note 1) Bright Field Global Peak to Peak Non-Uniformity (Note 1) PRNU Bright Field Center Non-Uniformity (Note 1) Maximum Photoresponse Non-Linearity High Gain (4,000 to 20,000 electrons) High Gain (4,000 to 40,000 electrons) Low Gain (8,000 to 80,000 electrons) Photodiode Charge Capacity (Note 3) Floating Diffusion Capacity - High Gain Floating Diffusion Capacity - Low Gain PNe - 44 - ke- Die 27, 40 FNe_HG 40 - - ke- Die 27, 40 ke- Die 27, 40 FNe_LG 160 - - Horizontal CCD Charge Transfer Efficiency HCTE 0.999995 0.999999 - Die Vertical CCD Charge Transfer Efficiency VCTE 0.999995 0.999999 - Die Photodiode Dark Current IPD - 7 70 e/p/s Die 40 Vertical CCD Dark Current IVD - 140 400 e/p/s Die 40 Image Lag Lag - - 10 e- Design Anti-Blooming Factor XAB 1,000 - - Vertical Smear Smr - -115 - dB Design Read Noise (Note 4) High Gain Low Gain ne-T - - e- rms Design Dynamic Range, Standard (Notes 4, 5) DR - 70.5 - dB Design Dynamic Range, Extended Linear Dynamic Range Mode (XLDR) (Notes 4, 5) XLDR - 82.5 - dB Design Output Amplifier DC Offset VODC - 9.0 - V Die Output Amplifier Bandwidth (Note 6) f-3db - 250 - MHz Die Output Amplifier Impedance ROUT - 127 - W Die mV/e- Design Output Amplifier Sensitivity High Gain Low Gain Design 12 45 DV/DN - - 33 8.7 www.onsemi.com 7 - - 27, 40 27, 40 KAI-04070 Table 6. PERFORMANCE SPECIFICATIONS (continued) Description Symbol Min. Nom. Max. Unit Sampling Plan Temperature Tested at (5C) KAI-04070-ABA AND KAI-04070-PBA AND KAI-04070-QBA CONFIGURATIONS Peak Quantum Efficiency Peak Quantum Efficiency Wavelength QEMAX - 52 - % Design lQE - 500 - nm Design % Design nm Design % Design nm Design KAI-04070-FBA AND KAI-04070-QBA GEN2 COLOR CONFIGURATIONS QEMAX Peak Quantum Efficiency Blue Green Red Peak Quantum Efficiency Wavelength Blue Green Red - - - 41 42 37 - - - - - - 460 535 610 - - - lQE KAI-04070-CBA AND KAI-04070-PBA GEN1 COLOR CONFIGURATIONS (Note 7) Peak Quantum Efficiency Blue Green Red QEMAX Peak Quantum Efficiency Wavelength Blue Green Red - - - 43 42 38 - - - - - - 470 540 620 - - - lQE 1. Per color. 2. Value is over the range of 10% to 90% of linear signal level saturation. 3. The operating value of the substrate voltage, VAB, will be marked on the shipping container for each device. The value of VAB is set such that the photodiode charge capacity is 440 mV. This value is determined while operating the device in the low gain mode. VAB value assigned is valid for both modes; high gain or low gain. 4. At 40 MHz. 5. Uses 20LOG (PNe / ne-T). 6. Assumes 5 pF load. 7. This color filter set configuration (Gen1) is not recommended for new designs. Low Gain Output of Sensor Not Verified Output of Sensor Not Verified 160,000 1,600 30,000 990 120,000 1,200 4,000 80,000 330 40,000 132 8,000 0 0 0 800 NL_LG1 Linearity Range 10,000 660 Output Signal (mV) 20,000 Output Signal (electrons) 1,320 NL_HG2 Linearity Range 40,000 80 0 Light or Exposure (arbitrary) 0 0 Figure 6. High Gain Linear Signal Range Light or Exposure (arbitrary) Figure 7. Low Gain Linear Signal Range www.onsemi.com 8 400 Output Signal (mV) High Gain NL_HG1 Linearity Range Output Signal (electrons) Linear Signal Range KAI-04070 TYPICAL PERFORMANCE CURVES Quantum Efficiency Monochrome with Microlens Figure 8. Monochrome with Microlens Quantum Efficiency Color (Bayer RGB) with Microlens(Gen2 and Gen1 CFA) Figure 9. Color (Bayer RGB) with Microlens Quantum Efficiency www.onsemi.com 9 KAI-04070 Color (TRUESENSE Sparse CFA) with Microlens (Gen2 and Gen1 CFA) Figure 10. Color (TRUESENSE Sparse CFA) with Microlens Quantum Efficiency Angular Quantum Efficiency For the curves marked "Horizontal", the incident light angle is varied in a plane parallel to the HCCD. For the curves marked "Vertical", the incident light angle is varied in a plane parallel to the VCCD. Monochrome with Microlens 100 Relative Quantum Efficiency (%) 90 Vertical 80 70 60 50 Horizontal 40 30 20 10 0 -40 -30 -20 -10 0 10 20 30 40 Angle (degrees) Figure 11. Monochrome with Microlens Angular Quantum Efficiency www.onsemi.com 10 KAI-04070 Color (Bayer RGB) with Microlens 100 90 Relative Quantum Efficiency (%) Vertical 80 70 60 50 Horizontal 40 30 20 10 0 -40 -30 -20 -10 0 10 20 30 40 Angle (degrees) Figure 12. Color (Bayer RGB) with Microlens Angular Quantum Efficiency Dark Current vs. Temperature 1,000.00 Photodiode VCCD Dark Current (e/s) 100.00 10.00 70C 60C 1.00 50C 40C 30C 0.10 20C 10C 0.01 2.90 3.00 3.10 3.20 3.30 3.40 1000/T (K) Figure 13. Dark Current vs. Temperature www.onsemi.com 11 3.50 3.60 KAI-04070 Power-Estimated Power-Estimated - Full Resolution 1.2 1.2 Single Dual (VOUTa/VOUTb) 1.0 1.0 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0.0 Power (W) Power (W) Quad 0.0 0 5 10 15 20 25 30 35 40 HCCD Frequency (MHz) Figure 14. Power - Full Resolution Power-Estimated - 1/4 Resolution - 2y2 Binning 1.2 1.2 Single Dual (VOUTa/VOUTb) 1.0 1.0 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0.0 0.0 0 5 10 15 20 25 30 35 HCCD Frequency (MHz) Figure 15. Power - 1/4 Resolution - Constant HCCD www.onsemi.com 12 40 Power (W) Power (W) Quad KAI-04070 Power-Estimated - 1/4 Resolution - 2y2 Binning using Variable HCCD XLDR 1.2 1.2 Single Dual (VOUTa/VOUTb) 1.0 1.0 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0.0 Power (W) Power (W) Quad 0.0 0 5 10 15 20 25 30 35 40 HCCD Frequency (MHz) Figure 16. Power - 1/4 Resolution - Variable HCCD XLDR Power-Estimated - 1/4 Resolution - 2y2 Binning using Constant HCCD XLDR 1.2 1.2 Single Dual (VOUTa/VOUTb) 1.0 1.0 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0.0 0.0 0 5 10 15 20 25 30 35 HCCD Frequency (MHz) Figure 17. Power - 1/4 Resolution - Constant HCCD XLDR www.onsemi.com 13 40 Power (W) Power (W) Quad KAI-04070 Frame Rates Frame Rates - Full Resolution Frame rates are for low and high gain modes of operation. 30 30 Single Dual (VOUTa/VOUTc) 25 25 Dual (VOUTa/VOUTb) 20 15 15 10 10 5 5 0 Frame Rate (fps) Frame Rate (fps) Quad 20 0 0 5 10 15 20 25 30 35 40 HCCD Frequency (MHz) Figure 18. Frame Rates - Full Resolution Frame Rates - 1/4 Resolution - 2y2 Binning Frame rates are for low and high gain modes of operation. 50 50 Single 45 45 Dual (VOUTa/VOUTc) Quad 35 Frame Rate (fps) 40 Dual (VOUTa/VOUTb) 35 30 30 25 25 20 20 15 15 10 10 5 5 0 0 0 5 10 15 20 25 30 35 HCCD Frequency (MHz) Figure 19. Frame Rates - 1/4 Resolution - Constant HCCD www.onsemi.com 14 40 Frame Rate (fps) 40 KAI-04070 Frame Rates - 1/4 Resolution - 2y2 Binning using Variable HCCD XLDR Frame rates for variable HCCD modes of operation. 40 40 Single 35 35 Dual (VOUTa/VOUTc) Dual (VOUTa/VOUTb) 30 30 25 25 20 20 15 15 10 10 5 5 0 Frame Rate (fps) Frame Rate (fps) Quad 0 0 5 10 15 20 25 30 35 40 HCCD Frequency (MHz) Figure 20. Frame Rates - 1/4 Resolution - Variable HCCD XLDR Frame Rates - 1/4 Resolution - 2y2 Binning using Constant HCCD XLDR Frame rates for a constant HCCD mode of operation. 40 40 Single 35 35 Dual (VOUTa/VOUTc) Dual (VOUTa/VOUTb) 30 30 25 25 20 20 15 15 10 10 5 5 0 0 0 5 10 15 20 25 30 35 40 HCCD Frequency (MHz) Figure 21. Frame Rates - 1/4 Resolution - Constant HCCD XLDR www.onsemi.com 15 Frame Rate (fps) Frame Rate (fps) Quad KAI-04070 DEFECT DEFINITIONS Table 7. OPERATION CONDITIONS FOR DEFECT TESTING AT 405C Description Condition Operational Mode One Output, using VOUTa, Continuous Readout HCCD Clock Frequency 20 MHz Pixels per Line 2,140 Lines per Frame 2,112 Line Time 115.0 ms Frame Time 242.9 ms Photodiode Integration Time (PD_Tint) Notes PD_Tint = Frame Time = 242.9 ms, No Electronic Shutter Used Temperature 40C Light Source Continuous Red, Green and Blue LED Illumination Operation 1 Nominal Operating Voltages and Timing 1. For monochrome sensor, only the green LED is used. Table 8. DEFECT DEFINITIONS FOR TESTING AT 405C Description Definition Standard Grade Notes Defect 83 mV 40 1 -12% Defect 12% 40 1 Defect 41 mV 400 Cluster Defect A group of 2 to 10 contiguous major defective pixels, but no more than 2 adjacent defect horizontally. 8 2 Column Defect A group of more than 10 contiguous major defective pixels along a single column. 0 2 Major Dark Field Defective Bright Pixel Major Bright Field Defective Pixel Minor Dark Field Defective Bright Pixel 1. For the color devices (KAI-04070-CBA and KAI-04070-PBA), a bright field defective pixel deviates by 12% with respect to pixels of the same color. 2. Column and cluster defects are separated by no less than two (2) good pixels in any direction (excluding single pixel defects). www.onsemi.com 16 KAI-04070 Table 9. OPERATION CONDITIONS FOR DEFECT TESTING AT 275C Description Condition Operational Mode Notes One Output, Using VOUTa, Continuous Readout HCCD Clock Frequency 20 MHz Pixels per Line 2,140 Lines per Frame 2,112 Line Time 115 ms Frame Time 242.9 ms Photodiode Integration Time (PD_Tint) PD_Tint = Frame Time = 242.9 ms, No Electronic Shutter Used Temperature 27C Light Source Continuous Red, Green and Blue LED Illumination Operation 1 Nominal Operating Voltages and Timing 1. For monochrome sensor, only the green LED is used. Table 10. DEFECT DEFINITIONS FOR TESTING AT 405C Description Definition Standard Grade Notes Defect 27 mV 40 1 -12% Defect 12% 40 1 Cluster Defect A group of 2 to 10 contiguous major defective pixels, but no more than 2 adjacent defect horizontally. 8 2 Column Defect A group of more than 10 contiguous major defective pixels along a single column. 0 2 Major Dark Field Defective Bright Pixel Major Bright Field Defective Pixel 1. For the color devices (KAI-04070-CBA and KAI-04070-PBA), a bright field defective pixel deviates by 12% with respect to pixels of the same color. 2. Column and cluster defects are separated by no less than two (2) good pixels in any direction (excluding single pixel defects). Defect Map defects are not included in the defect map. All defective pixels are reference to pixel 1, 1 in the defect maps. See Figure 22 for the location of pixel 1, 1. The defect map supplied with each sensor is based upon testing at an ambient (27C) temperature. Minor point www.onsemi.com 17 KAI-04070 TEST DEFINITIONS Test Regions of Interest Overclocking Image Area ROI: Active Area ROI: Center ROI: The test system timing is configured such that the sensor is overclocked in both the vertical and horizontal directions. See Figure 22 for a pictorial representation of the regions of interest. Pixel (1, 1) to Pixel (2080, 2080) Pixel (17, 17) to Pixel (2064, 2064) Pixel (991, 991) to Pixel (1090, 1090) Only the Active Area ROI pixels are used for performance and defect tests. 16 Dark Rows 24 Dark Columns 2048 x 2048 Active Pixels 16 Buffer Columns 16 Buffer Columns 24 Dark Columns 16 Buffer Rows Pixel 17, 17 Pixel 1, 1 16 Buffer Rows 16 Dark Rows VOUTa Figure 22. Regions of Interest Tests Dark Field Global Non-Uniformity This test is performed under dark field conditions. The sensor is partitioned into 256 sub regions of interest, each of which is 128 by 128 pixels in size. The average signal level of each of the 256 sub regions of interest is calculated. The signal level of each of the sub regions of interest is calculated using the following formula: are found. The dark field global uniformity is then calculated as the maximum signal found minus the minimum signal level found. Global Non-Uniformity This test is performed with the imager illuminated to a level such that the output is at 70% of saturation (approximately 924 mV). Prior to this test being performed the substrate voltage has been set such that the charge capacity of the sensor is 1,320 mV. Global non-uniformity is defined as Signal of ROI[i] + (ROI Average in Counts * * Horizontal Overclock Average in Counts) @ @ mV per Count Global Non-Uniformity + 100 @ Units : mVpp (millivolts Peak to Peak) where i = 1 to 256. During this calculation on the 256 sub regions of interest, the maximum and minimum signal levels Active Area Standard Deviation Active Area Signal Units : % rms Active Area Signal = Active Area Average - Dark Column Average www.onsemi.com 18 KAI-04070 Bright Field Defect Test This test is performed with the imager illuminated to a level such that the output is at approximately 924 mV. Prior to this test being performed the substrate voltage has been set such that the charge capacity of the sensor is 1,320 mV. The average signal level of all active pixels is found. The bright and dark thresholds are set as: Global Peak to Peak Non-Uniformity This test is performed with the imager illuminated to a level such that the output is at 70% of saturation (approximately 924 mV). Prior to this test being performed the substrate voltage has been set such that the charge capacity of the sensor is 1,320 mV. The sensor is partitioned into 256 sub regions of interest, each of which is 128 by 128 pixels in size. The average signal level of each of the 256 sub regions of interest (ROI) is calculated. The signal level of each of the sub regions of interest is calculated using the following formula: Dark Defect Threshold = Active Area Signal @ Threshold Bright Defect Threshold = Active Area Signal @ Threshold The sensor is then partitioned into 256 sub regions of interest, each of which is 128 by 128 pixels in size. In each region of interest, the average value of all pixels is found. For each region of interest, a pixel is marked defective if it is greater than or equal to the median value of that region of interest plus the bright threshold specified or if it is less than or equal to the median value of that region of interest minus the dark threshold specified. * Example for major bright field defective pixels: * Average value of all active pixels is found to be 924 mV * Dark defect threshold: 924 mV 12% = 111 mV * Bright defect threshold: 924 mV 12% = 111 mV * Region of interest #1 selected. This region of interest is pixels 17, 17 to pixels 144, 144 Median of this region of interest is found to be 920 mV Any pixel in this region of interest that is (920 - 111 mV) 809 mV in intensity will be marked defective Any pixel in this region of interest that is (920 + 111 mV) 1,031 mV in intensity will be marked defective * All remaining 144 sub regions of interest are analyzed for defective pixels in the same manner Signal of ROI[i] + (ROI Average in Counts * * Horizontal Overclock Average in Counts) @ @ mV per Count Where i = 1 to 256. During this calculation on the 144 sub regions of interest, the maximum and minimum signal levels are found. The global peak to peak uniformity is then calculated as: Global Uniformity + 100 @ Max. Signal * Min. Signal Active Area Signal Units : % pp Center Non-Uniformity This test is performed with the imager illuminated to a level such that the output is at 70% of saturation (approximately 924 mV). Prior to this test being performed the substrate voltage has been set such that the charge capacity of the sensor is 1,320 mV. Defects are excluded for the calculation of this test. This test is performed on the center 100 by 100 pixels of the sensor. Center uniformity is defined as: Center ROI Uniformity + 100 @ Center ROI Standard Deviation Center ROI Signal Units : % rms Center ROI Signal = Center ROI Average - Dark Colum Average Dark Field Defect Test This test is performed under dark field conditions. The sensor is partitioned into 256 sub regions of interest, each of which is 128 by 128 pixels in size. In each region of interest, the median value of all pixels is found. For each region of interest, a pixel is marked defective if it is greater than or equal to the median value of that region of interest plus the defect threshold specified in the "Detect Definitions" section. www.onsemi.com 19 KAI-04070 OPERATION Absolute Maximum Ratings description. If the level or the condition is exceeded, the device will be degraded and may be damaged. Operation at these values will reduce MTTF. Absolute maximum rating is defined as a level or condition that should not be exceeded at any time per the Table 11. ABSOLUTE MAXIMUM RATINGS Description Symbol Minimum Maximum Unit Notes Operating Temperature TOP -50 70 C 1 Humidity RH 5 90 % 2 Output Bias Current IOUT - 60 mA 3 CL - 10 pF Off-Chip Load Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Noise performance will degrade at higher temperatures. 2. T = 25C. Excessive humidity will degrade MTTF. 3. Total for all outputs. Maximum current is -15 mA for each output. Avoid shorting output pins to ground or any low impedance source during operation. Amplifier bandwidth increases at higher current and lower load capacitance at the expense of reduced gain (sensitivity). Table 12. ABSOLUTE MAXIMUM VOLTAGE RATINGS BETWEEN PINS AND GROUND Description Minimum Maximum Unit Notes VDDa, VOUTa -0.4 17.5 V 1 RDa -0.4 15.5 V 1 V1B, V1T ESD - 0.4 ESD + 24.0 V V2B, V2T, V3B, V3T, V4B, V4T ESD - 0.4 ESD + 14.0 V H1Sa, H1Ba, H2Sa, H2Ba, H2SLa, R1a, R2a, OGa ESD - 0.4 ESD + 14.0 V ESD -10.0 0.0 V SUB -0.4 40.0 V 1 2 1. a denotes a, b, c or d. 2. Refer to Application Note Using Interline CCD Image Sensors in High Intensity Visible Lighting Conditions * The KAI-04070 will operate in only the high gain KAI-08050 Compatibility The KAI-04070 is pin-for-pin compatible with a camera designed for the KAI-08050 image sensor with the following accommodations: * To operate in accordance with a system designed for KAI-08050, the target substrate voltage should be set to be 2.0V higher than the value recorded on the KAI-04070 shipping container. This setting will cause the charge capacity to be limited to 20 ke- (or 660 mV) * On the KAI-04070, pins 17 (R2ab) and 51 (R2cd) should be left floating per the KAI-08050 Device Performance Specification * * mode (33 mV/e-) All timing and voltages are taken from the KAI-08050 specification sheet The number of horizontal and vertical CCD clock cycles is reduced as appropriate In addition, if the intent is to operate the KAI-04070 image sensor in a camera designed for the KAI-08050 sensor that has been modified to accept and process the full 40,000 e- (1,320 mV) output, the following changes to the RD bias must be made: Table 13. Pins Names KAI-08050 KAI-04070 10, 26, 44, 60 RDa, RDb, RDc, RDd 12.0 V per the Specification Increase to 12.6 V To make use of the low or dual gains modes the KAI-04070 voltages and timing specifications must be used. www.onsemi.com 20 KAI-04070 Reset Pin, Low Gain (R2ab and R2cd) The R2ab and R2bc (pins 17 and 51) each have an internal circuit to bias the pins to 4.3 V. This feature assures the device is set to operate in the high gain mode when pins 17 VDD (+15 V) and 51 are not connected in the application to a clock driver (for KAI-08050 compatibility). Typical capacitor coupled drivers will not drive this structure. VDD (+15 V) R2 4.3 V 68 kW 68 kW 20 kW 20 kW 27 kW 27 kW GND GND Figure 23. Equivalent Circuit for Reset Gate, Low Gain (R2ab and R2cd) Power-Up and Power-Down Sequence Adherence to the power-up and power-down sequence is critical. Failure to follow the proper power-up and power-down sequences may cause damage to the sensor. Do Not Pulse the Electronic Shutter until ESD is Stable V+ VDD SUB Time ESD V- VCCD Low HCCD Low Activate All Other Biases when ESD is Stable and Sub is above 3 V Notes: 1. Activate all other biases when ESD is stable and SUB is above 3 V. 2. Do not pulse the electronic shutter until ESD is stable. 3. VDD cannot be +15 V when SUB is 0 V. 4. The image sensor can be protected from an accidental improper ESD voltage by current limiting the SUB current to less than 10 mA. SUB and VDD must always be greater than GND. ESD must always be less than GND. Placing diodes between SUB, VDD, ESD and ground will protect the sensor from accidental overshoots of SUB, VDD and ESD during power on and power off. See the figure below. Figure 24. Power-Up and Power-Down Sequence www.onsemi.com 21 KAI-04070 The VCCD clock waveform must not have a negative overshoot more than 0.4 V below the ESD voltage. 0.0 V ESD ESD - 0.4 V All VCCD Clock Absolute Maximum Overshoot of 0.4 V Figure 25. VCCD Clock Waveform Example of external diode protection for SUB, VDD and ESD. a denotes a, b, c or d. VDDa SUB GND ESD Figure 26. Example of External Diode Protection www.onsemi.com 22 KAI-04070 DC Bias Operating Conditions Table 14. DC BIAS OPERATING CONDITIONS Pins Symbol Min. Nom. Max. Unit Max. DC Current Notes Reset Drain RDa RD 12.4 12.6 12.8 V 10 mA 1, 9 Output Gate OGa OG -2.2 -2.0 -1.8 V 10 mA 1 Output Amplifier Supply VDDa VDD 14.5 15.0 15.5 V 11.0 mA 1, 2 Ground GND GND 0.0 0.0 0.0 V -1.0 mA Substrate SUB VSUB 5.0 VAB VDD V 50 mA 3, 8 ESD Protection Disable ESD ESD -9.2 -9.0 Vx_L V 50 mA 6, 7, 10 VOUTa IOUT -3.0 -5.0 -10.0 mA - 1, 4, 5 Description Output Bias Current VDDa RDa Ra R2a 1. a denotes a, b, c or d. 2. The maximum DC current is for one output. IDD = IOUT + ISS. See Figure 27. 3. The operating value of the substrate voltage, VAB, will be marked on the shipping container for each device. The value of VAB is set such that the photodiode charge capacity is the nominal PNe (see Specifications). 4. An output load sink must be applied to each VOUT pin to activate each output amplifier. 5. Nominal value required for 40 MHz operation per output. May be reduced for slower data rates and lower noise. 6. Adherence to the power-up and power-down sequence is critical. See Sequence section. 7. ESD maximum value must be less than or equal to V1_L + 0.4 V and V2_L + 0.4 V. 8. Refer to Application Note Using Interline CCD Image Sensors in High Intensity Visible Lighting Conditions. 9. 12.0 V may be used if the total output signal desired is 20,000 e- or less. 10. Where Vx_L is the level set for V1_L, V2_L, V3_L, or V4_L in the application. IDD HCCD Floating Diffusion IOUT VOUTa OGa ISS Source Follower #1 Figure 27. Output Amplifier www.onsemi.com 23 Source Follower #2 Source Follower #3 KAI-04070 AC Operating Conditions Table 15. CLOCK LEVELS Description Vertical CCD Clock, Phase 1 Vertical CCD Clock, Phase 2 Pins (Note 1) Symbol Level Min. Nom. Max. Unit V1B, V1T V1_L Low -8.2 -8.0 -7.8 V V1_M Mid -0.2 0.0 0.2 V1_H High 11.5 12.0 12.5 V2B, V2T V2_L Low -8.2 -8.0 -7.8 V2_H High -0.2 0.0 0.2 V3_L Low -8.2 -8.0 -7.8 Vertical CCD Clock, Phase 3 V3B, V3T V3_H High -0.2 0.0 0.2 Vertical CCD Clock, Phase 4 V4B, V4T V4_L Low -8.2 -8.0 -7.8 V4_H High -0.2 0.0 0.2 H1Sa H1S_L Low -5.2 -4.0 -3.8 H1S_A Amplitude (Note 3) 3.8 4.0 5.2 H1B_L Low -5.2 -4.0 -3.8 H1B_A Amplitude (Note 3) 3.8 4.0 5.2 Horizontal CCD Clock, Phase 1 Storage Horizontal CCD Clock, Phase 1 Barrier Horizontal CCD Clock, Phase 2 Storage H1Ba H2Sa H2S_L Low -5.2 -4.0 -3.8 H2S_A Amplitude (Note 3) 3.8 4.0 5.2 -5.2 -4.0 -3.8 Horizontal CCD Clock, Phase 2 Barrier H2Ba H2B_L Low H2B_A Amplitude (Note 3) 3.8 4.0 5.2 Horizontal CCD Clock, Last Phase (Note 2) H2SLa H2SL_L Low -5.2 -5.0 -4.8 H2SL_A Amplitude (Note 3) 4.8 5.0 5.2 R_L Low -3.2 -3.0 -2.8 R_A Amplitude 6.0 - 6.4 Reset Gate R1a Reset Gate 2 R2a Electronic Shutter (Note 4) SUB R2_L Low -2.0 -1.8 -1.6 R2_A Amplitude 6.0 - 6.4 VES High 29.0 30.0 40.0 V V V V V V V V V V V 1. a denotes a, b, c or d. 2. Use separate clock driver for improved speed performance. 3. The horizontal clock amplitude should be set such that the high level reaches 0.0 V. Examples: a. If the minimum horizontal low voltage of -5.2 V is used, then a 5.2 V amplitude clock is required for a clock swing of -5.2 V to 0.0 V. b. If the maximum horizontal low voltage of -3.8 V is used, then a 3.8 V amplitude clock is required for a clock swing of -3.8 V to 0.0 V. 4. Refer to Application Note Using Interline CCD Image Sensors in High Intensity Visible Lighting Conditions. The figure below shows the DC bias (VSUB) and AC clock (VES) applied to the SUB pin. Both the DC bias and AC clock are referenced to ground. VES VSUB GND GND Figure 28. DC Bias and AC Clock Applied to the SUB Pin www.onsemi.com 24 KAI-04070 Capacitance Table 16. CAPACITANCE V1B V2B V3B V4B V1T V2T V3T V4T GND All Pins Unit V1B X 4 3 3 2 2 2 1 10 25 nF V2B X X 1 3 1 1 1 1 10 20 nF V3B X X X 5 2 1 2 1 6 23 nF V4B X X X X 2 1 1 1 13 23 nF V1T X X X X X 2 3 2 20 29 nF V2T X X X X X X 5 3 4 21 nF V3T X X X X X X X 2 9 24 nF V4T X X X X X X X X 3 20 nF VSUB 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 2.8 2.8 nF H2S H1B H2B GND All Pins Unit H1S 32 29 29 120 210 pF H2S X 16 21 170 240 pF H1B X X 7 155 210 pF H2B X X X 165 235 pF 1. Tables show typical cross capacitance between pins of the device. 2. Capacitance is total for all like pins. 3. Capacitance values are estimated. Device Identification The device identification pin (DevID) may be used to determine which Truesense Imaging 7.4 micron pixel interline CCD sensor is being used. Table 17. DEVICE IDENTIFICATION Description Device Identification Pins Symbol Min. Nom. Max. Unit Max. DC Current Notes DevID DevID 64,000 74,000 84,000 W 50 mA 1, 2, 3 1. Nominal value subject to verification and/or change during release of preliminary specifications. 2. If the Device Identification is not used, it may be left disconnected. 3. After Device Identification resistance has been read during camera initialization, it is recommended that the circuit be disabled to prevent localized heating of the sensor due to current flow through the R_DeviceID resistor. Recommended Circuit Note that V1 must be a different value than V2. V1 V2 R_external DevID ADC R_DeviceID GND KAI-04070 Figure 29. Device Identification Recommended Circuit www.onsemi.com 25 KAI-04070 TIMING Requirements and Characteristics Table 18. REQUIREMENTS AND CHARACTERISTICS Description Symbol Min. Nom. Max. Unit Photodiode Transfer tPD 1.0 - - ms VCCD Leading Pedestal t3P 4.0 - - ms VCCD Trailing Pedestal t3D 4.0 - - ms VCCD Transfer tV 2.0 - - ms VVCR 75 - 100 % 1 tVR, tVF 5 - 10 % 1, 2 VCCD Clock Cross-Over VCCD Rise, Fall Times Notes tHS 2.0 - - ms HCCD Transfer te 25.0 - - ns Shutter Transfer tSUB 2.0 - - ms Shutter Delay tHD 2.0 - - ms Reset Pulse tR 2.5 - - ns Reset - Video Delay tRV - 2.2 - ns tHV - 3.1 - ns tLINE 34.9 - - ms Dual HCCD Readout 61.5 - - ms Single HCCD Readout 36.9 - - ms Quad HCCD Readout 73.8 - - ms Dual HCCD Readout 129.9 - - ms Single HCCD Readout 69.8 - - ms Dual HCCD Readout 123.0 - - ms Single HCCD Readout 36.9 - - ms Quad HCCD Readout 73.7 - - ms Dual HCCD Readout 129.9 - - ms Single HCCD Readout 29.8 - - ms Quad HCCD Readout 59.5 - - ms Dual HCCD Readout 101.7 - - ms Single HCCD Readout HCCD Delay H2SL - Video Delay Line Time Frame Time Line Time (XLDR Bin 2x2) tFRAME tLINE Frame Time (XLDR Bin 2x2) Constant HCCD Timing tFRAME Frame Time (XLDR Bin 2x2) Variable HCCD Timing tFRAME 1. Refer to Figure 47: VCCD Clock Rise Time, Fall Time, and Edge Alignment. 2. Relative to the VCCD Transfer pulse width, tV. www.onsemi.com 26 KAI-04070 Timing Flow Charts In the timing flow charts the number of HCCD clock cycles per row, NH, and the number of VCCD clock cycles per frame, NV, are shown in the following table. Table 19. VALUES FOR NH AND NV WHEN OPERATING THE SENSOR IN THE VARIOUS MODES OF RESOLUTION Full Resolution 1/4 Resolution NV NH NV Quad 1056 1076 Dual VOUTa, VOUTc 1056 2152 Dual VOUTa, VOUTb 2112 Single VOUTa 2112 1. 2. 3. 4. 5. XLDR NH NV NH 528 538 528 538 528 1076 528 1076 1076 1056 538 1056 538 2152 1056 1076 1056 1076 The time to read out one line tLINE = Line Timing + NH / (Pixel Frequency). The time to read out one frame tFRAME = NV tLINE + Frame Timing. Line Timing: See Table 21: Line Timing. Frame Timing: See Table 20: Frame Timing. XLDR: eXtended Linear Dynamic Range. No Electronic Shutter In this case the photodiode exposure time is equal to the time to read out an image. This flow chart applies to both full and 1/4 resolution modes. Frame Timing (see Table 20) Line Timing (see Table 21) Pixel Timing (see Table 22) Repeat NH Times Repeat NV Times Figure 30. Timing Flow when Electronic Shutter is Not Used www.onsemi.com 27 KAI-04070 Using the Electronic Shutter This flow chart applies to both the full and 1/4 resolution modes. The exposure time begins on the falling edge of the electronic shutter pulse on the SUB pin. The exposure time ends on the falling edge of the photodiode transfer (tPD) of the V1T and V1B pins. The electronic shutter timing is shown in Figure 38. Frame Timing (see Table 20) Line Timing (see Table 21) Pixel Timing (see Table 22) Repeat NH Times Repeat NV-NEXP Times Electronic Shutter Timing Line Timing (see Table 21) Pixel Timing (see Table 22) Repeat NH Times Repeat NEXP Times NOTE: NEXP: Exposure time in increments of number of lines. Figure 31. Timing Flow Chart using the Electronic Shutter for Exposure Control www.onsemi.com 28 KAI-04070 Timing Tables Frame Timing This timing table is for transferring charge from the photodiodes to the VCCD. See Figures 32 and 33 for frame timing diagrams. Table 20. FRAME TIMING Full Resolution, High Gain or Low Gain Device Pin Dual VOUTa VOUTc Quad Dual VOUTa VOUTb Single VOUTa 1/4 Resolution, High Gain or Low Gain Dual VOUTa VOUTc Quad Dual VOUTa VOUTb Single VOUTa 1/4 Resolution XLDR Dual VOUTa VOUTc Quad Dual VOUTa VOUTb Single VOUTa V1T F1T F1B F1T F1B F1T F1B V2T F2T F4B F2T F4B F2T F4B V3T F3T F3B F3T F3B F3T F3B V4T F4T F2B F4T F2B F4T F2B V1B F1B F1B F1B V2B F2B F2B F2B V3B F3B F3B F3B V4B F4B F4B F4B H1Sa P1 P1Q P1XL H1Ba P1 P1Q P1XL H2Sa P2 P2Q P2XL H2Ba P2 P2Q P2XL Ra RHG/RLG RHGQ/RLGQ RXL H1Sb H1Bb P1 P1 P2 P1Q P1 H2Sb P2 P1Q P1XL P2Q P2 P1Q P2Q P1XL P2XL P2Q P1XL P2XL P2XL H2Bb P2 P1 P2 P1 P2Q P1Q P2Q P1Q P2XL P1XL P2XL P1XL Rb RHG/ RLG (Note 1) RHG/ RLG (Note 1) RHGQ/ RLGQ (Note 1) RHGQ/ RLGQ (Note 1) RXL (Note 1) RXL (Note 1) R2ab R2HG/R2LG R2HGQ/R2LGQ R2XL H1Sc P1 (Note 1) P1Q (Note 1) P1XL (Note 1) H1Bc P1 (Note 1) P1Q (Note 1) P1XL (Note 1) H2Sc P2 (Note 1) P2Q (Note 1) P2XL (Note 1) H2Bc P2 (Note 1) P2Q (Note 1) P2XL (Note 1) Rc RHG/RLG (Note 1) RHGQ/RLGQ (Note 1) RXL (Note 1) H1Sd P1 (Note 1) P1Q (Note 1) P1XL (Note 1) H1Bd P1 H2Sd P2 (Note 1) P2 P1Q (Note 1) P2Q (Note 1) P2Q P1XL (Note 1) P2XL P2XL (Note 1) (Note 1) H2Bd P2 P1 (Note 1) P2Q P1Q (Note 1) P2XL P1XL (Note 1) Rd RHG/ RLG (Note 1) (Note 1) RHGQ/ RLGQ (Note 1) (Note 1) RXL (Note 1) (Note 1) R2cd R2HG/R2LG (Note 1) R2HGQ/R2LGQ (Note 1) R2XL (Note 1) SHP (Note 2) SHP1 SHPQ (Note 4) SHD (Note 2) SHD1 SHDQ (Note 5) 1. This clock should be held at its high level voltage (0 V) or held at +5.0 V for compatibility with TRUESENSE 5.5 micron Interline Transfer CCD family of products. 2. SHP and SHD are the sample clocks for the analog front end (AFE) signal processor. 3. This note intentionally left empty. 4. Use SHPLG for the AFE processing the low gain signal. Use SHPHG for the AFE processing the high gain signal. 5. Use SHDLG for the AFE processing the low gain signal. Use SHDHG for the AFE processing the high gain signal. www.onsemi.com 29 KAI-04070 Line Timing This timing is for transferring one line of charge from the VCCD to the HCCD. See Figure 34, Figure 35, Figure 36 and Figure 37 for line timing diagrams. Table 21. LINE TIMING Full Resolution, High Gain or Low Gain Device Pin Dual VOUTa VOUTc Quad Dual VOUTa VOUTb Single VOUTa 1/4 Resolution, High Gain or Low Gain Dual VOUTa VOUTc Quad Dual VOUTa VOUTb Single VOUTa 1/4 Resolution XLDR Dual VOUTa VOUTc Quad Dual VOUTa VOUTb Single VOUTa V1T L1T L1B 2 x L1T 2 x L1B 2 x L1T 2 x L1B V2T L2T L4B 2 x L2T 2 x L4B 2 x L2T 2 x L4B V3T L3T L3B 2 x L3T 2 x L3B 2 x L3T 2 x L3B V4T L4T L2B 2 x L4T 2 x L2B 2 x L4T 2 x L2B V1B L1B 2 x L1B 2 x L1B V2B L2B 2 x L2B 2 x L2B V3B L3B 2 x L3B 2 x L3B V4B L4B 2 x L4B 2 x L4B H1Sa P1L P1LQ P1XL H1Ba P1L P1LQ P1XL H2Sa P2L P2LQ P2XL H2Ba P2L P2LQ P2XL Ra RHG/RLG RHGQ/RLGQ RXL H1Sb H1Bb P1L P1L P2L P1LQ P1L H2Sb P2L P1LQ P2LQ P2L P1XL P1LQ P2LQ P1XL P2XL P2LQ P1XL P2XL P2XL H2Bb P2L P1L P2L P1L P2LQ P1LQ P2LQ P1LQ P2XL P1XL P2XL P1XL Rb RHG/ RLG (Note 1) RHG/ RLG (Note 1) RHGQ/ RLGQ (Note 1) RHGQ/ RLGQ (Note 1) RXL (Note 1) RXL (Note 1) R2ab R2HG/R2LG R2HGQ/R2LGQ R2XL H1Sc P1L (Note 1) P1LQ (Note 1) P1XL (Note 1) H1Bc P1L (Note 1) P1LQ (Note 1) P1XL (Note 1) H2Sc P2L (Note 1) P2LQ (Note 1) P2XL (Note 1) H2Bc P2L (Note 1) P2LQ (Note 1) P2XL (Note 1) Rc RHG/RLG (Note 1) RHGQ/RLGQ (Note 1) RXL (Note 1) H1Sd P1L (Note 1) P1LQ (Note 1) P1XL (Note 1) H1Bd P1L H2Sd P2L (Note 1) P2L P1LQ (Note 1) P2LQ (Note 1) P2LQ P1XL (Note 1) P2XL P2XL (Note 1) (Note 1) H2Bd P2L P1L (Note 1) P2LQ P1LQ (Note 1) P2XL P1XL (Note 1) Rd RHG/ RLG (Note 1) (Note 1) RHGQ/ RLGQ (Note 1) (Note 1) RXL (Note 1) (Note 1) R2cd R2HG/R2LG (Note 1) R2HGQ/R2LGQ (Note 1) R2XL (Note 1) SHP (Note 2) SHP1 SHPQ (Note 4) SHD (Note 2) SHD1 SHDQ (Note 5) 1. This clock should be held at its high level voltage (0 V) or held at +5.0 V for compatibility with TRUESENSE 5.5 micron Interline Transfer CCD family of products. 2. SHP and SHD are the sample clocks for the analog front end (AFE) signal processor. 3. The notation 2x L1B means repeat the L1B timing twice for every line. This sums two rows into the HCCD. 4. Use SHPLG for the AFE processing the low gain signal. Use SHPHG for the AFE processing the high gain signal. 5. Use SHDLG for the AFE processing the low gain signal. Use SHDHG for the AFE processing the high gain signal. www.onsemi.com 30 KAI-04070 Pixel Timing This timing is for transferring one pixel from the HCCD to the output amplifier. Table 22. PIXEL TIMING Full Resolution, High Gain or Low Gain Device Pin Dual VOUTa VOUTc Quad Dual VOUTa VOUTb Single VOUTa 1/4 Resolution, High Gain or Low Gain Dual VOUTa VOUTc Quad Dual VOUTa VOUTb Single VOUTa 1/4 Resolution XLDR Dual VOUTa VOUTc Quad Dual VOUTa VOUTb V1T -8 V -8 V -8 V V2T -8 V -8 V -8 V V3T 0V 0V 0V V4T 0V 0V 0V V1B -8 V -8 V -8 V V2B 0V 0V 0V V3B 0V 0V 0V V4B -8 V -8 V -8 V H1Sa P1 P1Q P1XL H1Ba P1 P1Q P1XL H2Sa P2 P2Q P2XL H2Ba P2 P2Q P2XL Ra RHG/RLG RHGQ/RLGQ RXL H1Sb H1Bb P1 P1 P2 P1Q P1 H2Sb P2 P1Q P1XL P2Q P2 Single VOUTa P1Q P2Q P1XL P2XL P2Q P1XL P2XL P2XL H2Bb P2 P1 P2 P1 P2Q P1Q P2Q P1Q P2XL P1XL P2XL P1XL Rb RHG/ RLG (Note 1) RHG/ RLG (Note 1) RHGQ/ RLGQ (Note 1) RHGQ/ RLGQ (Note 1) RXL (Note 1) RXL (Note 1) R2ab R2HG/R2LG R2HGQ/R2LGQ R2XL H1Sc P1 (Note 1) P1Q (Note 1) P1XL (Note 1) H1Bc P1 (Note 1) P1Q (Note 1) P1XL (Note 1) H2Sc P2 (Note 1) P2Q (Note 1) P2XL (Note 1) H2Bc P2 (Note 1) P2Q (Note 1) P2XL (Note 1) Rc RHG/RLG (Note 1) RHGQ/RLGQ (Note 1) RXL (Note 1) H1Sd P1 (Note 1) P1Q (Note 1) P1XL (Note 1) H1Bd P1 H2Sd P2 (Note 1) P2 P1Q (Note 1) P2Q (Note 1) P2Q P1XL (Note 1) P2XL P2XL (Note 1) (Note 1) H2Bd P2 P1 (Note 1) P2Q P1Q (Note 1) P2XL P1XL (Note 1) Rd RHG/ RLG (Note 1) (Note 1) RHGQ/ RLGQ (Note 1) (Note 1) RXL (Note 1) (Note 1) R2cd R2HG/R2LG (Note 1) R2HGQ/R2LGQ (Note 1) R2XL (Note 1) SHP (Note 2) SHP1 SHPQ (Note 4) SHD (Note 2) SHD1 SHDQ (Note 5) 1. This clock should be held at its high level voltage (0 V) or held at +5.0 V for compatibility with TRUESENSE 5.5 micron Interline Transfer CCD family of products. 2. SHP and SHD are the sample clocks for the analog front end (AFE) signal processor. 3. This note intentionally left empty. 4. Use SHPLG for the AFE processing the low gain signal. Use SHPHG for the AFE processing the high gain signal. 5. Use SHDLG for the AFE processing the low gain signal. Use SHDHG for the AFE processing the high gain signal. www.onsemi.com 31 KAI-04070 Timing Diagrams The charge in the photodiodes its transfer to the VCCD on the rising edge of the +12 V pulse and is completed by the falling edge of the +12 V pulsed on F1T and F1B. During the time period when F1T and F1B are at +12 V (tPD) anti-blooming protection is disabled. The photodiode integration time ends on the falling edge of the +12 V pulse. Frame Timing - Quadrant and Dual VOUTa/VOUTc Readout Modes Frame Timing Device Pin V1T Pattern tV 2 tV 2 tV 2 t3P tPD t3D tV 2 tV 2 tV 2 tV 2 +12 V 0V F1T -8 V 0V V2T F2T -8 V 0V V3T F3T -8 V 0V V4T F4T -8 V +12 V V1B 0V F1B -8 V 0V V2B F2B -8 V 0V V3B F3B -8 V 0V V4B F4B -8 V tV 2 tV 2 tV 2 Pixel Timing t3P tPD t3D tV 2 tV 2 tV 2 tV 2 Frame Timing NOTE: See Table 20 for pin assignments. Figure 32. Frame Timing Diagram Quadrant and Dual VOUTa/VOUTc Readout Modes www.onsemi.com 32 Line Timing KAI-04070 Frame Timing - Single and Dual VOUTa/VOUTb Readout Modes Frame Timing Device Pin V1T Pattern tV 2 tV 2 tV 2 t3P tPD t3D tV 2 tV 2 tV 2 tV 2 +12 V 0V F1B -8 V 0V V2T F4B -8 V 0V V3T F3B -8 V 0V V4T F2B -8 V +12 V V1B 0V F1B -8 V 0V V2B F2B -8 V 0V V3B F3B -8 V 0V V4B F4B -8 V tV 2 tV 2 tV 2 Pixel Timing t3P tPD t3D tV 2 tV 2 tV 2 Frame Timing NOTE: See Table 20 for pin assignments. Figure 33. Frame Timing Diagram Single and Dual VOUTa/VOUTb Readout Modes www.onsemi.com 33 tV 2 Line Timing KAI-04070 Line Timing -Full Resolution - Quadrant and Dual VOUTa/VOUTc Readout Modes Line Timing Time Duration is 4 tV Device Pin tV 2 Pattern tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 0V V1T L1T -8 V 0V V2T L2T -8 V 0V V3T L3T -8 V 0V V4T L4T -8 V 0V V1B L1B -8 V 0V V2B L2B -8 V 0V V3B L3B -8 V 0V V4B L4B Cl ocks Hor izont al -8 V 0V P1L -4 V 0V P2L -4 V tV 2 tV 2 tV 2 tV 2 Frame or Pixel Timing tV 2 Line Timing tV 2 tV 2 tV 2 Pixel Timing te 2 NOTE: See Table 21 for pin assignments. Figure 34. Line Timing Diagram - Full Resolution - Quadrant and Dual VOUTa/VOUTc Readout Modes www.onsemi.com 34 KAI-04070 Line Timing -Full Resolution - Single and Dual VOUTa/VOUTb Readout Modes Line Timing Time Duration is 4 tV Device Pin tV 2 Pattern tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 0V V1T L1B -8 V 0V V2T L4B -8 V 0V V3T L3B -8 V 0V V4T L2B -8 V 0V V1B L1B -8 V 0V V2B L2B -8 V 0V V3B L3B -8 V 0V V4B L4B Cl ocks Hor izont al -8 V 0V P1L -4 V 0V P2L -4 V tV 2 tV 2 tV 2 tV 2 Frame or Pixel Timing tV 2 Line Timing tV 2 tV 2 tV 2 Pixel Timing te 2 NOTE: See Table 21 for pin assignments. Figure 35. Line Timing Diagram - Full Resolution - Single and Dual VOUTa/VOUTb Readout Modes www.onsemi.com 35 KAI-04070 Line Timing - Low Gain, High Gain and XLDR 1/4 Resolution - Quadrant and Dual VOUTa/VOUTc Readout Modes 1/4 Resolution Line Timing Time Duration is 8 tV Device Pin Pattern V1T L1T tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 0V -8 V 0V V2T L2T -8 V 0V V3T L3T -8 V 0V V4T L4T -8 V 0V V1B L1B -8 V 0V V2B L2B -8 V 0V V3B L3B -8 V 0V Hor izont al Cl ocks V4B L4B -8 V 0V P1L -4 V 0V P2L -4 V tV 2 tV 2 tV 2 Frame or Pixel Timing tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 1/4 Resolution Line Timing tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 Pixel Timing te 2 NOTE: See Table 21 for pin assignments. Figure 36. Line Timing Diagram - 1/4 Resolution - Quadrant and Dual VOUTa/VOUTc Readout Modes www.onsemi.com 36 KAI-04070 Line Timing - Low Gain, High Gain and XLDR 1/4 Resolution - Single and Dual VOUTa/VOUTb Readout Modes 1/4 Resolution Line Timing Time Duration is 8 tV Device Pin Pattern V1T L1B tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 0V -8 V 0V V2T L4B -8 V 0V V3T L3B -8 V 0V V4T L2B -8 V 0V V1B L1B -8 V 0V V2B L2B -8 V 0V V3B L3B -8 V 0V Hor izont al Cl ocks V4B L4B -8 V 0V P1L -4 V 0V P2L -4 V tV 2 tV 2 tV 2 Frame or Pixel Timing tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 1/4 Resolution Line Timing tV 2 tV 2 tV 2 tV 2 tV 2 tV 2 Pixel Timing te 2 NOTE: See Table 21 for pin assignments. Figure 37. Line Timing Diagram - 1/4 Resolution - Single and Dual VOUTa/VOUTb Readout Modes www.onsemi.com 37 KAI-04070 finished. The HCCD clocks can be run during the electronic shutter pulse as long as the HCCD does not contain valid image data. For short exposures less than one line time, the electronic shutter pulse can appear inside the frame timing. Any electronic shutter pulse transition should be tV/2 away from any VCCD clock transition. Electronic Shutter Timing Diagrams The electronic shutter pulse can be inserted at the end of any line of the HCCD timing. The HCCD should be empty when the electronic shutter is pulsed. A recommended position for the electronic shutter is just after the last pixel is read out of a line. The VCCD clocks should not resume until at least tV/2 after the electronic shutter pulse has tV 2 tV 2 tSUB VES SUB VAB 0V VCCD Clock -8 V Figure 38. Electronic Shutter Timing tFRAME V1T/V1B SUB tINT Figure 39. Frame/Electrical Shutter Timing www.onsemi.com 38 KAI-04070 Pixel Timing - Full Resolution - High Gain Pixel Timing Use this timing to read out every pixel at high gain. If the sensor is to be permanently operated at high gain, the R2ab and R2cd pins can be left floating or set to any DC voltage between +3 V and +5 V. Note the R2ab and R2cd pins are internally biased to +4.3 V when left floating. The SHP1 and SHD1 pulses indicate where the camera electronics should sample the video waveform. The SHP1 and SHD1 pulses are not applied to the image sensor. te Device Pin Pattern VOUTa Video Ra RHG +3 V -3 V +4.2 V R2a R2HG -1.8 V SHP1 SHD1 0V Hor izont al Cl ocks P1 -4 V 0V P2 -4 V tR Figure 40. Pixel Timing Diagram - Full Resolution - High Gain www.onsemi.com 39 KAI-04070 Pixel Timing - Full Resolution - Low Gain Pixel Timing Use this pixel timing to read out every pixel at low gain. If the sensor is to be permanently operated at low gain, the Ra, Rb, Rc and Rd pins should be set to any DC voltage between +3 V and +5 V. The SHP1 and SHD1 pulses indicate where the camera electronics should sample the video waveform. The SHP1 and SHD1 pulses are not applied to the image sensor. te Device Pin Pattern VOUTa Video Ra RLG +3 V -3 V +4.2 V R2a R2LG -1.8 V SHP1 SHD1 0V Hor izont al Cl ocks P1 -4 V 0V P2 -4 V tR Figure 41. Pixel Timing Diagram - Full Resolution - Low Gain www.onsemi.com 40 KAI-04070 Pixel Timing - 1/4 Resolution - High Gain Pixel Timing Use this timing to read out two pixels summed on the output amplifier sense node at high gain. If the sensor is to be permanently operated at high gain, the R2ab and R2cd pins can be left floating or set to any DC voltage between +3 V and +5 V. Note the R2ab and R2cd pins are internally biased to +4.3 V when left floating. The SHPQ and SHDQ pulses indicate where the camera electronics should sample the video waveform. The SHPQ and SHDQ pulses are not applied to the image sensor. The Ra, Rb, Rc, and Rd pins are pulsed at half the frequency of the horizontal CCD clocks. This causes two pixels to be summed on the output amplifier sense node. The SHPQ and SHDQ clocks are also half the frequency of the horizontal CCD clocks. 2 te Device Pin Pattern VOUTa Video Ra RHGQ +3 V -3 V +4.2 V R2a R2HGQ -1.8 V SHP1 SHD1 Hor izont al Cl ocks 0V P1Q -4 V 0V P2Q -4 V tR te Figure 42. Pixel Timing Diagram - 1/4 Resolution - High Gain www.onsemi.com 41 KAI-04070 Pixel Timing - 1/4 Resolution - Low Gain Pixel Timing Use this timing to read out two pixels summed on the output amplifier sense node at low gain. If the sensor is to be permanently operated at low gain, the Ra, Rb, Rc and Rd pins can be set to any DC voltage between +3 V and +5 V. The SHPQ and SHDQ pulses indicate where the camera electronics should sample the video waveform. The SHPQ and SHDQ pulses are not applied to the image sensor. The R2ab and R2cd pins are pulsed at half the frequency of the horizontal CCD clocks. This causes two pixels to be summed on the output amplifier sense node. The SHPQ and SHDQ clocks are also half the frequency of the horizontal CCD clocks. 2 te Device Pin Pattern VOUTa Video Ra RLGQ +3 V -3 V +4.2 V R2a R2LGQ -1.8 V SHP1 SHD1 Hor izont al Cl ocks 0V P1Q -4 V 0V P2Q -4 V tR te Figure 43. Pixel Timing Diagram - 1/4 Resolution - Low Gain www.onsemi.com 42 KAI-04070 XLDR Pixel Timing To operate the sensor in extended linear dynamic range (XLDR) mode, the following pixel timing should be used. This mode requires two sets of analog front end (AFE) signal processing electronic units for each output. As shown in Figure 44 one AFE samples the pixel at low gain (SHPLG and SHDLG) and the other AFE samples the pixel at high gain (SHPHG and SHDHG). Two HCCD pixels are summed on the output amplifier node to obtain enough charge to fully use the 82 dB range of the XLDR timing. Combined with two-line VCCD summing, a total of 160,000 electrons of signal (4 x 40,000) SHDLG SHPLG can be sampled with 12 electrons or less noise. Note that a linear dynamic range of 82 dB is very large. Ensure that the camera optics is capable of focusing an 82 dB dynamic range image on the sensor. Lens flare caused by inexpensive optics or even dust on the lens will limit the dynamic range. The timing shown in Figure 46 shows the HCCD not being clocked at a constant frequency. If the HCCD cannot be clocked at a variable frequency, then the HCCD may be clocked at a constant frequency (Figure 45) at the expense of about 33% slower frame rate. Low Gain AFE Low Gain Digital Out High Gain AFE High Gain Digital Out SHPHG Caution: In the XLDR mode the output of the CCD can produce large signals that may damage some AFE devices. If there is the potential for damage to the AFE, the CCD output should be electronically attenuated. SHDHG Sensor Output Figure 44. XLDR Timing - AFE Connections Block Diagram www.onsemi.com 43 KAI-04070 Pixel Timing - 1/4 Resolution - XLDR Pixel Timing - Constant HCCD Timing 4 te Device Pin Pattern VOUTa Video Ra RXL +3 V -3 V +4.2 V R2a R2XL -1.8 V SHPLG SHDLG SHPHG SHDHG Hor izont al Cl ocks 0V P1XL -4 V 0V P2XL -4 V tR te te te te Figure 45. Pixel Timing Diagram - 1/4 Resolution - XLDR - Constant HCCD Timing www.onsemi.com 44 KAI-04070 Pixel Timing - 1/4 Resolution - XLDR Pixel Timing - Variable HCCD Timing 3 te Device Pin Pattern VOUTa Video Ra RXL +3 V -3 V +4.2 V R2a R2XL -1.8 V SHPLG SHDLG SHPHG SHDHG Hor izont al Cl ocks 0V P1XL -4 V 0V P2XL -4 V tR te te te Figure 46. Pixel Timing Diagram - 1/4 Resolution - XLDR - Variable HCCD Timing www.onsemi.com 45 KAI-04070 VCCD Clock Edge Alignment VVCR 90% tV 10% tVF tVR tV tVF tVR Figure 47. VCCD Clock Rise Time, Fall Time and Edge Alignment www.onsemi.com 46 KAI-04070 MECHANICAL INFORMATION Completed Assembly Notes: 1. See Ordering Information for marking code. 2. No materials to interfere with clearance through guide holes. 3. Units: mm. Figure 48. Completed Assembly (1 of 2) Notes: 1. Optical center of image is nominally at the package center. 2. Units: mm. Figure 49. Completed Assembly (2 of 2) www.onsemi.com 47 KAI-04070 Cover Glass Notes: 1. Substrate = Schott D263T eco. 2. Dust, Scratch, Inclusion Specification: 10 mm maximum size in Zone A. 3. MAR coated both sides. 4. Spectral Transmission: a. T > 98.0% 420-435 nm b. T > 99.2% 435-630 nm c. T > 98.0% 630-680 nm 5. Units: mm. Figure 50. Cover Glass www.onsemi.com 48 KAI-04070 Cover Glass Transmission 100 90 80 Transmission (%) 70 60 50 40 30 20 10 0 200 300 400 500 600 700 Wavelength (nm) Figure 51. Cover Glass Transmission www.onsemi.com 49 800 900 KAI-04070 REFERENCES For information on ESD and cover glass care and cleanliness, please download the Image Sensor Handling and Best Practices Application Note (AN52561/D) from www.onsemi.com. For quality and reliability information, please download the Quality & Reliability Handbook (HBD851/D) from www.onsemi.com. For information on device numbering and ordering codes, please download the Device Nomenclature technical note (TND310/D) from www.onsemi.com. For information on environmental exposure, please download the Using Interline CCD Image Sensors in High Intensity Lighting Conditions Application Note (AND9183/D) from www.onsemi.com. For information on Standard terms and Conditions of Sale, please download Terms and Conditions from www.onsemi.com. For information on soldering recommendations, please download the Soldering and Mounting Techniques Reference Manual (SOLDERRM/D) from www.onsemi.com. ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 50 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative KAI-04070/D Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ON Semiconductor: KAI-04070-PBA-JD-BA KAI-04070-ABA-JD-BA KAI-04070-CBA-JD-BA KAI-04070-ABA-JR-BA KAI-04070-QBA-JDBA KAI-04070-FBA-JD-BA