AMP* Commercial BNC Jack Connectors for PC Board and Pane! Mounting AMF Instruction Sheet 408-2769 {was IS 2769) 17MAR93 Rev CONNECTOR P/N RIGHT-ANGLE MOUNTING CONNECTOR P/N 226978 PANEL 27676 227678 PANEL (Ref) PC BOARD ; PC BOARD 227433 (Ref (Ref) (Ref) 226990 227661 227679 HEX NUT 227677 1-329631-2 227161 413194 222092 222093 414459 413879 WITH FLANGE LOCKWASHER LOCKWASHER HEX NUT 1~329632-2 1-329632-2 1-329631-2 NOTE SEE FIGURE 2(A) FOR MOUNTING DIMENSIONS NOTE SEE FIGURE 2/8} FOR MOUNTING DIMENSIONS CONNECTOR P/N VERTICAL MOUNTING CONNECTOR P/N 226987 226993 HEX NUT 227670 HEX NUT LOCKWASHER GS 1-320631-2 227671 1-329631~2 LOGKWASHER 1-329632~2 227674 CS- {-329632-2 PANEL 227675 PC BOARD (Ref) 227672 (Ref) PANEL PC BOARD 227673 (Ref) (Ref) 227222 FLANGE NOTE SEE FIGURE 2(C) FOR MOUNTING DIMENSIONS Figure 1 1. INTRODUCTION This instruction sheet covers the installation of AMP Commercial BNC Jack Connectors with the base part numbers fisted in Figure 1. All dimensions on this sheet are in millimeters [with inch equivalents provided in brackets]. iiustrations are for identification only and are not drawn to scale. 2. DESCRIPTION These connectors are designed for printed circuit (pc) board and pane!~mount applications. There are styles available with and without mounting flanges for right-angle and vertical-mount installation, with metal and plastic body materials, with and without mounting posts, and with tin-, silver-, and gold-plated center contacts. The style used will depend on the AMP Incorporated, Harrisburg, PA. 17105 TOOLING ASSISTANCE CENTER 1 800 722-1111 AMP FAX/PRODUCT INFO 1 800-522-6752 413528 222132 NOTE SEE FIGURE 2(D) FOR MOUNTING DIMENSIONS 200-153E application requirements. Refer to the applicable AMP Customer Drawing for additional information. 3. MOUNTING PROCEDURE (Figure 2) A. PC Board Mounting The maximum recommended pe board thickness is 3.175 mm [.125 in}. 1. Make a hole layout in the pc board using the dimensions provided in the illustration for the connector being installed. 2. Secure the connector to the pc board. a. If mounting a connector with mounting flanges, use two 5-40 screws, and secure the connector to the board with two nuts on the underside of the pc board. b. if mounting a connector without mounting flanges and without mounting posts, use two 1of2 This AMP controlled document is subject to change. For latest revision cail the AMP FAX number. Copyright 1978, 1981, 1983, 1993 by AMP Incorporated. All International Rights Reserved. Trademark Per EC-0130-0053-92, 0990-0071-33 AMP AMP Commercial BNC Jack Connectors 408-2769 2-56 self-tapping screws, and secure the con- nector through the underside of the pc board. For flangeless, metal-body connectors, use 6.350 mm [250 in] self-tapping screws (AMP part no. 221108-4) with 1.587 mm [.0625 in.] thick pe board, and 7.925 mm [.312 in.] self-fapping screws (AMP part no. 221108-2) with 3.175 mm [125 in.] thick pe board. For flangeless, plastic-body connectors, use 7.925 mim [.312 in] self-tapping screws (AMP part no. 221108-2) with either pc board thickness. c. If mounting a connector without mounting B. Panel Mounting The recommended panel thickness is from 1.168 mm [.046 in] through 6.350 mm [.250 in_]. 1. If the connector is to be mounted through a panel, make a D-shaped hole using the applicable dimensions provided in the illustration below. 2. Secure the connector to the panel with AMP Hex Nut 1-329631~2 and AMP Lockwasher 1-329632-2, or equivalent. flanges and with mounting posts, solder the NOTE Signal and ground posts should be hand- or posts in the mounting holes. wave-soldered to the pe board. VIEW A PANEL CUTOUT | VIEW B PANEL CUTOUT 14.22 [-560] L. K PANEL 4 le 12.884 14-00 5.536+.08.00 | SFE CUSTOMER 12.83+4.19+.00 505+.005/-.000 . 834.136, .536+.08+-.00 [ ] [.218+.003/-.000} DRAWING FOR [.505-. 0054.00] [.218+.009.000} 15.88 a HEIGHT ~ MOUNTING HEIGHT be PC BOARD HOLE LAYOUT mn ..89+.08 pL PC BOARD HOLE LAYOUT 7.87[.310] REF} [,035 +.003] im 10.16 DIATYP 7.87,.310)REFR [400] 244 a oe USE 2.64 [.104] DIA TYP CLEARANCE HOLE FOR 2-56 SELF-TAPPING SCREWS, _[.200} 7 fe USE 2.00.07] DIA FOR @ MOUNTING POST APPLICATION 94. og 2.54 5.08 [-100] 9.302.130) DIA TYP CLEARANCE HOLE 5.08 FOR 5~40 SCREW [,900} [.035 +.003] [200] DIATYP VIEWC PANEL CUTOUT | VIEW D PANEL CUTOUT | 12.83+.13/-.00 5.536+.08-.00 r 505+.005-.000 to 12.83+4.13+-.00 5.536+.08-.00 ro [: } [-218+.0034- 00] _ [505+.005+.000] [.2184.003/-,000] 34.91[1.375] 04.93 f MOUNTING i 375) HEIGHT MOUNTING PC BOARD HOLE LAYOUT L PC BOARD HOLE LAYOUT HEIGHT | (89 +.08[.095 +.003} - DIATYP rig tee 10.16 22.86 Pt I ion [.400} 1.900] ae 08 USE 2.64 [.104] DIA TYP [095 +003 CLEARANCE HOLE FOR 3.302.130] DIA TYP OIA TYP 2-56 SELF-TAPPING SCREWS. CLEARANCE HOLE + USE 2.00 [.079] DIA FOR FOR 5-40 SCREW MOUNTING POST APPLICATION Figure 2 200-154E 20f2 Rev