SML-81 series Datasheet lFeatures lOutline * Reverse-mount available type lSize 1006 (0402) 3412 (1305) 3.4x1.25mm (t=1.1mm) 1.0x0.6mm (t=0.2mm) Color Type V U D W M B WB lDimensions lRecommended Solder Pattern (unit : mm) (note) Tolerance is within 0.1mm unless otherwise specified Except burr on terminal from consideration. (unit : mm) lSpecifications Part No. Chip Structure SML-811VT(A) Color Absolute Maximum Ratings (Ta=25C) Peak Forward Reverse Operating Temp. Storage Temp. Dissipation Current Current Voltage PD(mW) IF(mA) IFP(mA) VR(V) Topr(C) Tstg(C) Power Forward AIGaInP Orange 62 25 100* 2 Typ. (V) IF Max. (mA) (mA) VR (V) Yellow SML-812MT Yellowish Green 65 SML812BCT Blue 80 20 100*2 White 33 10 50*2 InGaN 5 -40 to +85 -40 to +100 1.95 10 5 100 SML-811WT(A) SML813WBC8W Electrical and Optical Characteristics (Ta=25C) Forward Voltag VF Reverse Current IR Red SML-811UT(A) SML-811DT(A) Emitting 60*1 4 5 -30 to +85 -40 to +85 2.1 -30 to +85 -40 to +85 3.3 -40 to +85 -40 to +100 2.9 4 20 5 10 5 Dominant Wavelength lD Luminous Intensity IV IF Min. Typ. Min.*3 Typ. Max.*3 IF (nm) (nm) (nm) (mA) (mcd) (mcd) (mA) 625 630 636 615 620 625 602 605 608 587 590 593 14 28 569 572 575 14 40 464 470 476 22 56 22 45 (0.30, 0.30) 10 20 5 11.2 22.4 10 20 5 *1:Duty1/5, 200Hz *2:Duty1/10, 1kHz *3:Reference www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. 1/10 2013.10 - Rev.E Data Sheet SML-81 series lElectrical Characteristics Curves Fig.2 Luminous Intensity Atmosphere Temperature FORWARD CURRENT : IF [mA] 100 SML-811VT(A) SML-811UT(A) SML-811DT(A) SML-811WT(A) SML-812MT Ta=25C 10 1 1.4 1.6 1.8 2.0 2.2 RELATIVE LUMINOUS INTENSITY [a.u.] Fig.1 Forward Current - Forward Voltages 2.4 FORWARD VOLTAGE : VF [V] 2.0 Ta=25C 1.5 1.0 0.5 0.0 0 5 10 15 20 25 FORWARD CURRENT : IF [mA] www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. 1.4 1.2 1 0.8 SML-811VT(A) SML-811UT(A) SML-811DT(A) SML-811WT(A) SML-812MT 0.6 0.4 -40-30-20-10 0 10 20 30 40 50 60 70 80 90100 Fig.4 Derating MAXIMUM FORWARD CURRENT : [mA] RELATIVE LUMINOUS INTENSITY SML-811VT(A) SML-811UT(A) SML-811DT(A) SML-811WT(A) SML-812MT IF=10mA IF=20mA ATMOSPHERE TEMPERATURE : Ta [C] Fig.3 Luminous Intensity - Forward Current 2.5 1.6 30 20 10 SML-811VT(A) SML-811UT(A) SML-811DT(A) SML-811WT(A) SML-812MT 0 -40 -20 0 20 40 60 80 100 AMBIENT TEMPERATURE : Ta [C] 2/10 2013.10 - Rev.E Data Sheet SML-81 series lElectrical Characteristics Curves Fig.2 Luminous Intensity Atmosphere Temperature FORWARD CURRENT : IF [mA] 100 SML812BC7T RELATIVE LUMINOUS INTENSITY [a.u.] Fig.1 Forward Current - Forward Voltages Ta=25C 10 1 2.2 2.6 3.0 3.4 3.8 FORWARD VOLTAGE : VF [V] MAXIMUM FORWARD CURRENT : [mA] RELATIVE LUMINOUS INTENSITY Ta=25C 1.0 0.8 0.6 0.4 0.2 0 4 8 12 16 1.2 1 0.8 SML812BC7T 0.6 -40 -20 0 20 40 60 80 100 Fig.4 Derating 1.2 0.0 IF=20mA ATMOSPHERE TEMPERATURE : Ta [C] Fig.3 Luminous Intensity - Forward Current SML812BC7T 1.4 20 FORWARD CURRENT : IF [mA] 25 SML812BC7T 20 15 10 5 0 -40 -20 0 20 40 60 80 100 AMBIENT TEMPERATURE : Ta [C] *The value is based on the die destruction endurance; optical characteristics are NOT considered.. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. 3/10 2013.10 - Rev.E Data Sheet SML-81 series lElectrical Characteristics Curves Fig.2 Luminous Intensity Atmosphere Temperature 100 Ta=25C SML813WBC8W FORWARD CURRENT : IF [mA] RELATIVE LUMINOUS INTENSITY [a.u.] Fig.1 Forward Current - Forward Voltages 10 1 2.2 2.6 3.0 3.4 3.8 1.4 1.2 1 0.8 SML813WBC8W 0.6 FORWARD VOLTAGE : VF [V] MAXIMUM FORWARD CURRENT : [mA] RELATIVE LUMINOUS INTENSITY Ta=25C 1.5 1.0 0.5 0 2 4 6 8 -20 0 20 40 60 80 100 Fig.4 Derating 2.0 0.0 -40 ATMOSPHERE TEMPERATURE : Ta [C] Fig.3 Luminous Intensity - Forward Current SML813WBC8W IF=5mA 10 FORWARD CURRENT : IF [mA] 14 SML813WBC8W 12 10 8 6 4 2 0 -40 -20 0 20 40 60 80 100 AMBIENT TEMPERATURE : Ta [C] *The value is based on the die destruction endurance; optical characteristics are NOT considered.. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. 4/10 2013.10 - Rev.E Data Sheet SML-81 series lViewing Angle SML-81 series SCANNING ANGLE (deg) SML-81 series SCANNING ANGLE (deg) RELATIVE INTENSITY RELATIVE INTENSITY SML812BCT SML813WBC8W SCANNING ANGLE (deg) SML812BCT SML813WBC8W SCANNING ANGLE (deg) RELATIVE INTENSITY RELATIVE INTENSITY lRank Reference of Brightness Red(V,U) Rank Iv (mcd) SML-811VT(A)* SML-811UT(A)* (Ta=25C, IF10mA) AG AH 9.0 to 11.2 11.2 to 14 AJ 14 to 18 AK AL AM AN 18 to 22.4 22.4 to 28 28 to 35.5 35.5 to 45 AP AQ AR 45 to 56 56 to 71 71 to 90 AP AQ AR 45 to 56 56 to 71 71 to 90 AP AQ AR 45 to 56 56 to 71 71 to 90 R AS AT AU AV AW Orange(D) Rank Iv (mcd) SML-811DT(A)* (Ta=25C, IF10mA) AG AH 9.0 to 11.2 11.2 to 14 AJ 14 to 18 AK AL AM AN 18 to 22.4 22.4 to 28 28 to 35.5 35.5 to 45 AS AT AU AV AW (Ta=25C, IF10mA) AG AH 9.0 to 11.2 11.2 to 14 AJ 14 to 18 AK AL AM AN 18 to 22.4 22.4 to 28 28 to 35.5 35.5 to 45 AS AT AU AV AW AX 90 to 112 112 to 140 140 to 180 180 to 224 224 to 280 280 to 355 Green(M) Rank Iv (mcd) AX 90 to 112 112 to 140 140 to 180 180 to 224 224 to 280 280 to 355 Yellow(Y) Rank Iv (mcd) SML-811WT(A)* AX 90 to 112 112 to 140 140 to 180 180 to 224 224 to 280 280 to 355 (Ta=25C, IF20mA) G H J K L M N P Q 1.0 to 1.6 1.6 to 2.5 2.5 to 4.0 4.0 to 6.3 6.3 to 10 10 to 16 16 to 25 25 to 40 40 to 63 G H J K L M N P Q R 0.9 to 1.4 1.4 to 2.2 2.2 to 3.6 3.6 to 5.6 5.6 to 9 9 to 14 14 to 22 22 to 36 36 to 56 56 to 90 G H J K L M N P Q R 0.9 to 1.4 1.4 to 2.2 2.2 to 3.6 3.6 to 5.6 5.6 to 9 9 to 14 14 to 22 22 to 36 36 to 56 56 to 90 S T U V 63 to 100 100 to 160 160 to 250 250 to 400 400 to 630 W X 630 to 1000 1000 to 1600 SML-812MT Blue(B) Rank Iv (mcd) SML812BCT (Ta=25C, IF20mA) S T U V White(WB) Rank Iv (mcd) SML813WBC8W W 90 to 140 140 to 220 220 to 360 360 to 560 560 to 900 X 900 to 1400 (Ta=25C, IF5mA) S T U V W 90 to 140 140 to 220 220 to 360 360 to 560 560 to 900 X 900 to 1400 *Please note that the brightness of some products may fall between ranks (half rank). Brightness on specification sheet include tolerance of within 10%. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. 5/10 2013.10 - Rev.E Data Sheet SML-81 series lSpectrum Data IF=10mA 1.0 0.8 0.6 0.4 SML812BCT SML-812MT 0.8 0.6 0.4 0.2 0.2 0.0 IF=20mA 1.0 INTENSITY [a.u.] INTENSITY [a.u.] SML-811VT(A) SML-811UT(A) SML-811DT(A) SML-811WT(A) 380 480 580 680 0.0 780 380 WAVELENGTH [nm] 480 580 680 780 WAVELENGTH [nm] IF=5mA 1 INTENSITY [a.u.] SML813WBC8W 0.8 0.6 0.4 0.2 0 380 480 580 680 780 WAVELENGTH [nm] * Please take this data as a reference data for the samples are measured randomly. * The data is relativized for each color. It is NOT to show the spectrum peaks are equal. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. 6/10 2013.10 - Rev.E Data Sheet SML-81 series lChromaticity Diagram [Chromaticity Coordimates] (Ta=25C, IF5mA) A F x y x H y x K y x y 0.280 0.248 0.283 0.305 0.287 0.295 0.304 0.330 CIE y 0.296 0.276 0.304 0.330 0.307 0.315 0.330 0.360 0.283 0.305 0.307 0.315 0.311 0.294 0.330 0.318 K 0.264 0.267 0.287 0.295 0.296 0.276 0.311 0.294 F Measurement tolerance : 0.02 H A CIE x 8.0 1.2 +0.1 -0.03 +1 0 0 -3 60 180 1 13 11.4 (00.5) 1.5 0.1 5.5 0.1 0 3.7 0.1 1.5 1.75 Cathode Index 2 0.05 3.5 4 0.1 0.1 lTaping [T86 / 1(white)] Packing quantity 3000pcs/reel Pull direction (note) Tolerance is within 0.2mm unless otherwise specified Unit ( www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. 7/10 ):Reference 2013.10 - Rev.E Data Sheet SML-81 series lPart No. Construction lPacking Specification ROHM LED products are being shipped with desiccant (silica gel) concluded in moisture-proof bags. Pasting the moisture sensitive label on the outer surface of the moisture-proof bags or enclosing the humidity indication card inside the bag is available upon request. Please contact the nearest sales office or distributer if necessary. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. 8/10 2013.10 - Rev.E Data Sheet SML-81 series lAttention Points In Handling This product was developed as a surface mount LED especially suitable for soldering. Please take care of following points when using this device. f2.4 Hole 1.25 1.DESIGNING OF PCB As for a recommendable solder pattern, Please refer to Fig-1. The size and direction of the pad pattern depends on the condition of the PCB, 4.2 Thorough design review is recommended before the final designing. (unit : mm) This product of structured with rear/bottom electrode to be soldered. (Fig-1) The formation of solder fillet is not guaranteed due to its electrode shape 2.SOLDERING (Sn-Cu, Sn-Ag-Cu, Sn-Ag-Bi-Cu) LED products do not contain reinforcement materials such as glass fillers. Therefore, thermal stress by soldering greatly influence its reliability. The temperature conditions for reflow soldering should therefore be set up according to the characteristic of this product. (See Fig-2) Number of reflow process shall be max 2 times and these processes shall be performed in a row. Max.260C, Within 10sec 140 to 180C 230 to 260C Min.1 min Max. 40sec (Fig-2) Cooling process to normal temperature shall be required between first and second soldering process. 3.WASHING Please note the following points when washing is required after soldering. 3-1) WASHING SOLVENT Isopropyl alcohol or other alcohol solvent is recommendable. 3-2) TEMPERATURE Below 30C, immersion time ; within 3 minutes. 3-3) ULTRA SONIC WASHING Below 15/1 litter of solvent tub. 3-4) COOLING Below 100C within 3 minutes. 4.EROSION GAS Utilization in erosion gas atmosphere may degenerate the plating surface which might cause deterioration of solder strength, optical characteristics, or functions. Please take precautions against occurrence of gas from the surrounding parts on the occasion of custody, and also after mounted on circuit board. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. 9/10 2013.10 - Rev.E Data Sheet SML-81 series 5.STORAGE At reflow soldering, the reliability of this product is often influenced by moisture absorption so we apply the packaging with moisture proof for better condition is use, please also note that 5-1) Not to be opened before using. 5-2) To be kept in our moisture proof packaging with some desiccant (SILICA GEL) after opening it. To be baked in case the SILICA GEL indicator its color from either blue to clear or green to pink. 5-3) Please use within 168 hours after the package was opened. (Condition at 30C, max.70%Rh.) In case it is not used within 168 hours, please put it back into our packaging. 5-4) BAKING Please bake under reel condition at 60C, 1224 hours (max.20%Rh) after un-sealing. While baking is done, the reel and emboss tape may be easily deformed. Please be careful not to give any stress. 6.LIFE TIME This product will cause reduction of luminous intensity depending on the using conditions and environmental. Please inquire our sales contact if long life time is required on your application. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. 10/10 2013.10 - Rev.E Notice Notes 1) The information contained herein is subject to change without notice. 2) Before you use our Products, please contact our sales representative and verify the latest specifications : 3) Although ROHM is continuously working to improve product reliability and quality, semiconductors can break down and malfunction due to various factors. Therefore, in order to prevent personal injury or fire arising from failure, please take safety measures such as complying with the derating characteristics, implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no responsibility for any damages arising out of the use of our Poducts beyond the rating specified by ROHM. 4) Examples of application circuits, circuit constants and any other information contained herein are provided only to illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. 5) The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM or any other parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of such technical information. 6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communication, consumer systems, gaming/entertainment sets) as well as the applications indicated in this document. 7) The Products specified in this document are not designed to be radiation tolerant. 8) For use of our Products in applications requiring a high degree of reliability (as exemplified below), please contact and consult with a ROHM representative : transportation equipment (i.e. cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells, and power transmission systems. 9) Do not use our Products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power control systems, and submarine repeaters. 10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with the recommended usage conditions and specifications contained herein. 11) ROHM has used reasonable care to ensur the accuracy of the information contained in this document. However, ROHM does not warrants that such information is error-free, and ROHM shall have no responsibility for any damages arising from any inaccuracy or misprint of such information. 12) Please use the Products in accordance with any applicable environmental laws and regulations, such as the RoHS Directive. For more details, including RoHS compatibility, please contact a ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations. 13) When providing our Products and technologies contained in this document to other countries, you must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the US Export Administration Regulations and the Foreign Exchange and Foreign Trade Act. 14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of ROHM. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. R1102A