Ethernet/10BaseT/100BaseT/1000BaseT Protector Ethernet/10BaseT/100BaseT/1000BaseT Protector The DO-214AA SIDACtor Ethernet protection series is intended for applications sensitive to load values. Typically, high speed connections require a lower capacitance. CO values are 40% lower than standard devices. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0220S_ 15 32 4 5 800 P0642S_** 58 77 4 5 800 2.2 50 50 2.2 120 P0722S_** 65 88 4 5 25 800 2.2 120 P0902S_** 75 98 4 25 5 800 2.2 120 P1102S_** 90 130 25 4 5 800 2.2 120 20 P1302S_ 120 P1402S_ 140 160 4 5 800 2.2 150 20 180 4 5 800 2.2 120 P1502S_ 20 140 180 4 5 800 2.2 150 20 P1802S_ 170 220 4 5 800 2.2 150 15 P2302S_ 190 260 4 5 800 2.2 150 15 P2602S_ 220 300 4 5 800 2.2 150 15 P3002S_ 280 360 4 5 800 2.2 120 15 P3502S_ 320 400 4 5 800 2.2 150 15 P4802S_ 440 600 4 5 800 2.2 120 15 * For surge ratings, see table below. ** Contact factory for release date. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 http://www.littelfuse.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 14 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2004 Littelfuse, Inc. SIDACtor(R) Data Book and Design Guide Ethernet/10BaseT/100BaseT/1000BaseT Protector Thermal Considerations Symbol TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W RJA Parameter Value Thermal Resistance: Junction to Ambient Unit IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2004 Littelfuse, Inc. SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 15 http://www.littelfuse.com +1 972-580-7777 Data Sheets Package DO-214AA