SIDACtor (R) Protection Thyristors SLIC Protection Battrax(R) Single Port Positive/Negative - MS-013 Description The Single Port Positive/Negative Battrax Series are programmable SIDACtor(R) devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. This series is designed specifically to protect SLIC devices utilizing positive and negative ringing signals. This one device will protect a single port. Features and Benefits Agency Approvals Agency t Low voltage overshoot t Low Capacitance t Low on-state voltage t Positive and negative ringing compatible t Does not degrade with use Agency File Number t Fails short circuit when surged in excess of ratings E133083 Pinout Designation t Single-port protect t Gate trgger tracking device Applicable Global Standards 1 6 2 5 3 4 t TIA-968-A t GR 1089 Intra-building t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level t YD/T 1082 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building Schematic Symbol 6 (Ground) (T) 1 (-VREF) 2 5 (+VREF) (R) 3 4 (Ground) Electrical Characteristics VDRM @lDRM=5A VS @100V/s V min V max IH Part Number Marking B3104UCLxx B3104UC IVREF* *7* IVREF* *7* IS mA min mA max 100 100 IT VT @IT=2.2 Amps Capacitance* A max V max pF min pF max 2.2 4 30 200 B3164UCLxx B3164UC IVREF* *7* IVREF* *7* 160 100 2.2 4 30 200 B3204UCLxx B3204UC IVREF* *7* IVREF* *7* 200 100 2.2 4 30 200 - VREF Max Value for the negative Battrax is -200 V. - VREF.BY7BMVFGPSUIFQPTJUJWF#BUUSBYJT 7 - XX = Part Number Suffix: `TP' (Tube Pack) or `RP' (Reel Pack). Notes: - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). - Devices are bi-directional - All electrical characteristics shown are defined from Tip (pin 1) to Ground (pin 4 & 6) and Ring (pin 3) to Ground (pin 4 & 6) (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. * Off-state capacitance (CO) is measured across pins 1 & 4,6 and 3 & 4,6 at 1 MHz with a 2V bias. 122 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors SLIC Protection Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/s max 200 50 500 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 1 C 1 1 1 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP $ *PP rating assumes VREFFRVBMT 7 - The device must initially be in thermal equilibrium with -40C < TJ < $ 1 Current waveform in s 2 Voltage waveform in s Thermal Considerations Package Symbol Modified MS-013 6 Parameter Value Unit TJ Operating Junction Temperature Range UP C TS Storage Temperature Range UP C 60 C/W 5 4 1 2 R0JA 3 Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform IPP VDRM IH VS VREF -VREF VDRM VT IS -V IDRM IS IT IPP VS IPP - Peak Pulse Current - %IPP +I IDRM +V IH tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 -I Normalized VS Change vs. Junction Temperature td tr t - Time (s) Normalized DC Holding Current vs. Case Temperature IH 8 6 25 C 4 IH (TC = 25C) 10 Ratio of Percent of VS Change - % 2.0 14 12 2 0 -4 -6 1.8 1.6 1.4 25C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C Junction Temperature (TJ) - C 123 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors SLIC Protection Soldering Parameters Pb-Free assembly (see Fig. 1) $ $ 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3C/sec. Max. TS(max) to TL - Ramp-up Rate 3C/sec. Max. Reflow - Temperature (TL) (Liquidus) Figure 1 TP $ - Temperature (tL) 60-150 secs. Peak Temp (TP) tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS $ 25 Time within 5C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6C/sec. Max. Time 25C to Peak Temp (TP) 8 min. Max. Do not exceed time to peak temperature (t 25C to peak) Time $ Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VDC Peak $PS $ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling $UP $ NJOEXFMM VQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC $ 3) VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage $IST.*-45% .FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65C, 1008 hrs. Thermal Shock $UP $ NJOEXFMM TFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) $ 3) BUN VQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat $ TFDT.*-45% .FUIPE Body Material UL recognized epoxy meeting flammability classification 94V-0 Moisture Sensitivity Level Part Numbering 3) $ IST SFnPXDZDMFT $1FBL +&%&$+45% -FWFM Part Marking B3 xx 4 U C L xx TYPE B3: Dual (Positive & Negative Battrax SIDACtor) PACKING OPTIONS RP: Reel Pack TP: Tube Pack XXXXXXX RoHS COMPLIANT Date Code HOLDING CURRENT 10: 100 mA 20: 200 mA 16: 160 mA CONSTRUCTION VARIABLE (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Part Marking Code (Refer to Electrical Characteristics Table) XXXXX IPP RATING PACKAGE TYPE 124 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors SLIC Protection Dimensions -- MS-013 Dimensions 0.065 (1.65) Pad Outline C 0.460 (11.68) 0.138 (3.50) Dimension are in inches (and millimeters). 0.059 (1.50) E D 7 TYP J 7 TYP A G Burr Side H 96 A Mold Split Line 4 A 7 TYP BSC* F 7 TYP MIN Length of Flat K Detail A B A B C D E F G H J K BSC* Inches Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 * BSC = Basic Spacing between Centers Packing Options Package Type U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 6-pin Tube Pack 500 (50 per tube) TP N/A Tape and Reel Specification -- MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification -- MS-013 Message Location .045 (1.14) .310 (7.87) 90 .165 (4.19) 6 Interior of the Tube .150 (3.81) .225 (5.72) .525 (13.34) (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. .020 .005 WALL TYP. (0.51 0.13) .108 (2.74) .005 A .110 (2.79) A Dimensions are in inches (and millimeters) 125 Revised: February 22, 2011 20.000 .030 (508.00 0.76) Millimeters 3.63