SIDACtor® Protection Thyristors
122
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
SLIC Protection
Battrax® Single Port Positive/Negative - MS-013
(T) 1
(-VREF) 2
(R) 3
6 (Ground)
4 (Ground)
5 (+VREF)
Electrical Characteristics
Description
Features and Benefits
t Low voltage overshoot
t Low on-state voltage
t Does not degrade with
use
t Fails short circuit when
surged in excess of
ratings
t Low Capacitance
t Positive and negative
ringing compatible
t Single-port protect
t Gate trgger tracking
device
Agency Approvals
Agency Agency File Number
E133083
Schematic Symbol
Pinout Designation
1
2
3
6
5
4
Part Number Marking
VDRM
@lDRM=5μA
VS
@100V/μs IHISIT
VT
@IT=2.2 Amps Capacitance*
V min V max mA min mA max A max V max pF min pF max
B3104UCLxx B3104UC I±VREF**7* I±VREF**7* 100 100 2.2 4 30 200
B3164UCLxx B3164UC I±VREF**7* I±VREF**7* 160 100 2.2 4 30 200
B3204UCLxx B3204UC I±VREF**7* I±VREF**7* 200 100 2.2 4 30 200
Applicable Global Standards
t TIA-968-A
t TIA-968-B
t ITU K.20/21 Enhanced
Level
t ITU K.20/21 Basic Level
t GR 1089 Inter-building
t GR 1089 Intra-building
t IEC 61000-4-5
t YD/T 1082
t YD/T 993
t YD/T 950
The Single Port Positive/Negative Battrax Series are
programmable SIDACtor® devices designed to protect
SLICs (Subscriber Line Interface Circuit) from damaging
overvoltage transients.
This series is designed specifically to protect SLIC devices
utilizing positive and negative ringing signals. This one
device will protect a single port.
Notes:
- Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted).
- Devices are bi-directional
- All electrical characteristics shown are defined from Tip (pin 1) to Ground (pin 4 & 6) and
Ring (pin 3) to Ground (pin 4 & 6)
- VREF Max Value for the negative Battrax is -200 V.
- VREF.BY7BMVFGPSUIFQPTJUJWF#BUUSBYJT7
- XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack).
* Off-state capacitance (CO) is measured across pins 1 & 4,6 and 3 & 4,6
at 1 MHz with a 2V bias.
SIDACtor® Protection Thyristors
123
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
SLIC Protection
Surge Ratings
Series
IPP ITSM
50/60 Hz di/dt
0.2x310 1
0.5x700 2
2x10 1
2x10 2
8x20 1
1.2x50 2
10x160 1
10x160 2
10x560 1
10x560 2
5x320 1
9x720 2
10x360 1
10x360 2
10x1000 1
10x1000 2
5x310 1
10x700 2
A min A min A min A min A min A min A min A min A min A min A/μs max
C 50 500 400 200 150 200 175 100 200 50 500
Package Symbol Parameter Value Unit
Modified MS-013
1
2
3
6
5
4
TJOperating Junction Temperature Range UP °C
TSStorage Temperature Range UP °C
R0JA Thermal Resistance: Junction to Ambient 60 °C/W
Thermal Considerations
IH
IT
IS
IS
IDRM
VT
+V
-V
+I
-I
VS
IH
VDRM
VREF
-VREF
VDRM
VS
IPP
IPP
IDRM
50
100
0
t
r
t
d
0
Peak
Value
Half Value
t – Time (μs)
I
PP
– Peak Pulse Current – %I
PP
t
r
= rise time to peak value
t
d
= decay time to half value
Waveform = t
r
x t
d
V-I Characteristics tr x td Pulse Waveform
25°C
Case Temperature (TC) - ºC
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
-40 -20 0 20 40 60 80 100 120 140 160
Ratio of IH
IH (TC = 25ºC)
Normalized VS Change vs. Junction Temperature
Normalized DC Holding Current vs. Case Temperature
-8
-40 -20 0 20 40 60 80 100 120 140 160
-6
-4
0
2
4
6
8
10
12
14
Junction Temperature (T
J
) – °C
Percent of V
S
Change – %
25 °C
Notes:
1 Current waveform in μs
2 Voltage waveform in μs
- Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product.
- IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$*PP rating assumes VREFFRVBMT7
- The device must initially be in thermal equilibrium with -40°C < TJ <¡$
SIDACtor® Protection Thyristors
124
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
SLIC Protection
Time
Temperature
T
P
T
L
T
S(max)
T
S(min)
25
t
P
t
L
t
S
time to peak temperature
(t 25ºC to peak)
Ramp-down
Ramp-up
Preheat
Critical Zone
T
L
to T
P
Figure 1
Soldering Parameters
Physical Specifications Environmental Specifications
Lead Material Copper Alloy
Terminal Finish 100% Matte-Tin Plated
Body Material UL recognized epoxy meeting flammability
classification 94V-0
Part Numbering Part Marking
High Temp Voltage
Blocking
80% Rated VDRM (VDC Peak ¡$PS¡$
504 or 1008 hrs. MIL-STD-750 (Method 1040)
JEDEC, JESD22-A-101
Temp Cycling
¡$UP¡$NJOEXFMMVQUP
cycles. MIL-STD-750 (Method 1051) EIA/JEDEC,
JESD22-A104
Biased Temp &
Humidity
52 VDC¡$3)VQUPIST&*"
JEDEC, JESD22-A-101
High Temp Storage ¡$IST.*-45%.FUIPE
JEDEC, JESD22-A-101
Low Temp Storage -65°C, 1008 hrs.
Thermal Shock
¡$UP¡$NJOEXFMMTFDUSBOTGFS
10 cycles. MIL-STD-750 (Method 1056) JEDEC,
JESD22-A-106
Autoclave (Pressure
Cooker Test)
¡$3)BUNVQUPIST&*"
JEDEC, JESD22-A-102
Resistance to Solder
Heat ¡$TFDT.*-45%.FUIPE
Moisture Sensitivity
Level
3)¡$ISTSFnPXDZDMFT
¡$1FBL+&%&$+45%-FWFM
Reflow Condition Pb-Free assembly
(see Fig. 1)
Pre Heat
- Temperature Min (Ts(min))¡$
- Temperature Max (Ts(max))¡$
- Time (Min to Max) (ts)60-180 secs.
Average ramp up rate (Liquidus Temp (TL)
to peak) 3°C/sec. Max.
TS(max) to TL - Ramp-up Rate 3°C/sec. Max.
Reflow
- Temperature (TL) (Liquidus) ¡$
- Temperature (tL)60-150 secs.
Peak Temp (TP)¡$
Time within 5°C of actual Peak Temp (tp)30 secs. Max.
Ramp-down Rate 6°C/sec. Max.
Time 25°C to Peak Temp (TP)8 min. Max.
Do not exceed ¡$
XXXXXXX
XXXXX
Part Marking Code
(Refer to Electrical Characteristics Table)
Date Code
B3 xx 4U C L xx
TYPE
HOLDING CURRENT
PACKAGE TYPE
IPP RATING
RoHS COMPLIANT
CONSTRUCTION VARIABLE
PACKING OPTIONS
RP: Reel Pack
TP: Tube Pack
B3: Dual (Positive & Negative
Battrax SIDACtor)
10: 100 mA 16: 160 mA
20: 200 mA
SIDACtor® Protection Thyristors
125
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
SLIC Protection
Package Type Description Quantity Added Suffix Industry Standard
U
Modified MS-013 6-pin
Tape and Reel Pack 1500 RP EIA-481-D
Modified MS-013 6-pin
Tube Pack
500
(50 per tube) TP N/A
Packing Options
Tape and Reel Specification — MS-013
Interior of the Tube
.045
(1.14)
.165
(4.19)
.150
(3.81)
90˚
.525
(13.34)
A
.225
(5.72)
Message Location
.310
(7.87) .108
(2.74) .005
20.000 ± .030
(508.00 ± 0.76)
.020 ± .005
(0.51 ± 0.13) WALL TYP.
.110
(2.79)
A
6
Dimensions are in inches
(and millimeters)
Direction of Feed
0.700
(17.8)
.512 (13.0) Arbor
Hole Dia.
12.99
(330)
.630
(16.0)
Dimensions are in inches
(and millimeters)
.472
(12.0)
.157
(4.0)
Tube Pack Specification — MS-013
Dimensions — MS-013
7º TYP
E
D
A
B
Mold Split
Line
A
7º TYP
7º TYP
Pad Outline
0.065
(1.65)
0.460
(11.68)
0.138
(3.50) 0.059
(1.50)
C
A
F7º TYP
G
J
H
Dimension are in inches
(and millimeters).
Burr Side
MIN Length
of Flat
4º
96º
Detail A
K
BSC*
Dimensions Inches Millimeters
Min Max Min Max
A0.360 0.364 9.14 9.25
B0.352 0.356 8.94 9.04
C0.400 0.412 10.16 10.46
D0.043 0.045 1.09 1.13
E0.047 0.055 1.19 1.40
F0.293 0.297 7.44 7.54
G0.289 0.293 7.34 7.44
H0.089 0.093 2.26 2.36
J0.041 0.049 1.04 1.24
K0.020 0.51
BSC* 0.133 0.143 3.38 3.63
* BSC = Basic Spacing between Centers