Technical Specification PQ40150QGx07 18-75V 15V 6.67A 100W 2000V dc Quarter-brick Continuous Input Outputs Current Max Power Isolation DC-DC Converter The PQ40150QGx07 PowerQor Giga quarter-brick converter is a next-generation, board-mountable, isolated, fixed switching frequency DC/DC converter that uses synchronous rectification to achieve extremely high conversion efficiency. The power dissipated by the converter is so low that a heatsink is not required, which saves cost, weight, height, and application effort. All of the power and control components are mounted to the multi-layer PCB substrate with highyield surface mount technology for greater reliability. The PQ40 module offers a wide input voltage range to cover both 24V and 48V applications. RoHS compliant, see last page. PQ40150QGx07 Module Operational Features * High efficiency, >90% at full rated load current * Delivers up to 6.67A of output current with minimal derating - no heatsink required * Ultra wide input voltage range: 18V - 75V, with 100V 100ms input voltage transient capability * Fixed frequency switching provides predictable EMI performance * No minimum load requirement means no preload resistors required. Protection Features * Input under-voltage lockout disables converter at low input voltage * Output current limit and short circuit protection protects converter from excessive load current or short circuits * Active back bias limit prevents damage to converter from external load induced pre-bias * Output over-voltage protection protects load from damaging voltages * Thermal shutdown protectsconverer from abnormal environmental conditions Mechanical Features * * * * Safety Features Industry standard pin-out configuration Standard Size:2.30"x1.45"x0.397" (58.4x36.8x10.08mm) Weight: 1.32 oz. (37.5 grams) Flanged pins designed to permit surface mount soldering, avoid wave solder using FPiP technique on open frame units * UL 60950-1:2007 * CAN/CSA-C22.2 No. 60950-1:2007 * EN60950-1/A12:2011 Control Features Contents * On/Off control referenced to input side (positive and negative logic options are available) * Remote sense for the output voltage compensates for output distribution drops * Output voltage trim permits custom voltages and voltage margining Product # PQ40150QGx07 Phone 1-888-567-9596 Page No. Mechanical Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Application Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 1 Input: Output: Current: Package: Open Frame Mechanical Diagram TOP VIEW 1.45 [36.8] .600 [15.24] .450 [11.43] .300 [7.62] .150 [3.81] 18-75V 15V 6.25A Quarter-brick SIDE VIEW .031 .027 [0.79 0.68] Bottomside Clearance 8 7 6 5 4 2.32 [58.9] 2.00 [50.8] 1 2 .180 [4.57] See Note 6 .397 .015 [10.08 0.38] Overall Height 3 .14 [3.6] .43 [10.8] .300 [7.62] .600 [15.24] NOTES 1) 2) 3) 4) 5) 6) Pins 1-3, 5-7 are 0.040" (1.02mm) diameter, with 0.080" (2.03mm) diameter standoff shoulders. Pins 4 and 8 are 0.062" (1.57 mm) diameter with 0.100" (2.54 mm) diameter standoff shoulders. Other pin extension lengths available. All Pins: Material - Copper Alloy- Finish - Matte Tin over Nickel plate Undimensioned components are shown for visual reference only. Weight: 1.32 oz. (37.5 grams) All dimensions in inches (mm) Tolerances: x.xx in +/-0.02 in. (x.xmm +/-0.5 mm) x.xxx in +/-0.010 in. (x.xxmm +/-0.25 mm) Product # PQ40150QGx07 Phone 1-888-567-9596 PIN DESIGNATIONS Pin Name Function 1 Vin(+) 2 ON/OFF Positive input voltage TTL input to turn converter on and off, referenced to Vin(-), with internal pull up. Negative input voltage Negative output voltage Negative remote sense (See note 1) Output voltage trim (See note 2) Positive remote sense (See note 3) Positive output voltage 3 Vin(-) 4 Vout(-) 5 SENSE(-) 6 TRIM 7 SENSE(+) 8 Vout(+) Notes: 1) SENSE(-) should be connected to Vout(-) either remotely or at the converter. 2) Leave TRIM pin open for nominal output voltage. 3) SENSE(+) should be connected to Vout(+) either remotely or at the converter. www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 2 Input: Output: Current: Package: Baseplated Mechanical Diagram TOP VIEW 18-75V 15V 6.25A Quarter-brick SIDE VIEW 1.47 [37.3] 1.03 [26.2] .600 [15.24] .450 [11.43] .300 [7.62] .150 [3.81] .22 [5.6] .031 .027 [0.79 0.68] Bottomside Clearance .23 [5.8] 8 7 6 5 4 2.32 [58.9] 2.002 1.86 [50.8] [47.2] M3 Threaded Inserts 4 Places See Notes 1 & 2 1 2 .180 [4.57] See Note 6 .469 .022 [11.91 0.55] Overall Height 3 .150 [3.81] .44 [11.1] .300 [7.62] .600 [15.24] NOTES 1) M3 screws used to bolt unit's baseplate to other surfaces (such as a heatsink) must not exceed 0.100" (2.54 mm) depth below the surface of the baseplate. 2) Applied torque per screw should not exceed 6in-lb. (0.7 Nm). 3) Baseplate flatness tolerance is 0.004" (.10mm) TIR for surface. 4) Pins 1-3, 5-7 are 0.040" (1.02mm) diameter, with 0.080" (2.03mm) diameter standoff shoulders. 5) Pins 4 and 8 are 0.062" (1.57 mm) diameter with 0.100" (2.54 mm) diameter standoff shoulders. 6) Other pin extension lengths available. Recommended pin length is 0.03" (0.76mm) greater than the PCB thickness. 7) All Pins: Material - Copper Alloy- Finish - Matte Tin over Nickel plate 8) Undimensioned components are shown for visual reference only. 9) Weight: 2.15 oz. (60.9 g) typical 10) All dimensions in inches (mm) Tolerances: x.xx in +/-0.02 in. (x.xmm +/-0.5 mm) x.xxx in +/-0.010 in. (x.xxmm +/-0.25 mm) Product # PQ40150QGx07 Phone 1-888-567-9596 PIN DESIGNATIONS Pin Name 1 Vin(+) 2 ON/OFF Function Positive input voltage TTL input to turn converter on and off, referenced to Vin(-), with internal pull up. Negative input voltage Negative output voltage Negative remote sense (See note 1) Output voltage trim (See note 2) Positive remote sense (See note 3) Positive output voltage 3 Vin(-) 4 Vout(-) 5 SENSE(-) 6 TRIM 7 SENSE(+) 8 Vout(+) Notes: 1) SENSE(-) should be connected to Vout(-) either remotely or at the converter. 2) Leave TRIM pin open for nominal output voltage. 3) SENSE(+) should be connected to Vout(+) either remotely or at the converter. www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 3 Input: Output: Current: Package: Technical Specifications 18-75V 15V 6.25A Quarter-brick PQ40150QGx07 Electrical Characteristics Ta = 25 C, airflow rate = 300 LFM, Vin = 48Vdc, nominal Vout unless otherwise noted; full operating temperature range is -40 C to +100 C ambient temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. ABSOLUTE MAXIMUM RATINGS Input Voltage Non-Operating Operating Operating Transient Protection 100 V Isolation Voltage (input to output) Operating Temperature Storage Temperature Voltage at ON/OFF input pin INPUT CHARACTERISTICS Operating Input Voltage Range Input Under-Voltage Lockout Turn-On Voltage Threshold Turn-Off Voltage Threshold Lockout Hysteresis Voltage Maximum Input Current No-Load Input Current Disabled Input Current Inrush Current Transient Rating Response to Input Transient Input Reflected Ripple Current Input Terminal Ripple Current Recommended Input Fuse Input Filter Component Values (L\C) Recommended External Input Capacitance OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance EFFICIENCY 100% Load (24Vin) 50% Load (24Vin) 100% Load (48Vin) 50% Load (48Vin) Product # PQ40150QGx07 Typ. -1 -40 -55 -2 Max. 100 80 100 2000 100 125 18 V V V V C C V V 18 48 75 16 14.5 1.0 16.5 15 1.5 17 15.5 2.0 6.17 160 4 0.03 80 2.0 350.0 5.0 145.0 20 1.5 \ 6.6 47.0 14.77 15.00 0.04 \ 6 0.04 \ 6 112 14.47 75 15 0 7 0.1 0 Phone 1-888-567-9596 8 13.2 0.3 10 Units Notes & Conditions 1.82 Continuous Continuous 100ms transient, square wave Basic insulation, Pollution Degree 2 V V V A 100% Load, 18Vin mA mA A2s mV 1000V/ms input transient, 48V-75V step mA P-P thru 10H inductor; Figures 17 & 19 mA RMS; Figures 17 & 18 A Fast blow external fuse recommended H\F Internal values; Figure E F V 0.2 \ 30 % (mV) 0.2 \ 30 % (mV) 300 mV 15.54 V over sample line, load and temperature 20MHz bandwidth; Figures 17 & 20 150 mV Full Load, Figures 17 & 20 30 mV Full Load, Figures 17 & 20 6.67 A Subject to thermal derating; Figures 5 - 12 9 A Output Voltage 10% Low; Figure 21 0.8 50 2000 90 91 89 90 www.synqor.com mA F Negative current drawn from output Negative current drawn from output 15Vout at 6.7A Resistive Load % % % % Figures Figures Figures Figures 1 1 1 1 - 4, 4, 4, 4, 24Vin 24Vin 48Vin 48Vin Doc.# 005-2QG157D Rev. C 11/27/12 Page 4 Input: Output: Current: Package: Technical Specifications 18-75V 15V 6.25A Quarter-brick PQ40150QGx07 Electrical Characteristics (continued) Ta = 25 C, airflow rate = 300 LFM, Vin = 48V dc unless otherwise noted; full operating temperature range is -40 C to +100 C baseplate temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. Typ. Max. Units Notes & Conditions DYNAMIC CHARACTERISTICS Input Voltage Ripple rejection 45.00 dB 120 Hz; Figure 24 Output Voltage Current Transient For a Step Change in Output Current (0.1A/s) 190 mV 50% to 75% to 50% Iout max; Figure 15 For a Step Change in Output Current (4A/s) 190 mV 50% to 75% to 50% Iout max; Figure 16 700 Settling Time s To within 1% Vout nom Turn-On Transient Turn-On Time 4 8 16 ms Full load, Vout=90% nom.; Figures 13 & 14 Start-Up Inhibit Period 180 200 240 ms -40C to +125C; Figure F Output Voltage Overshoot 0 % TEMPERATURE LIMITS FOR POWER DERATING CURVES Semiconductor Junction Temperature 125 C Package rated to 150C Board Temperature 125 C UL rated max operating temp 130C Transformer Temperature 125 C Figures 5 - 12 for derating curves ISOLATION CHARACTERISTICS Isolation Voltage 2000 V Isolation Resistance 10 M Isolation Capacitance 470 pF FEATURE CHARACTERISTICS Switching Frequency 291 315 340 kHz ON/OFF Control (Option P) Off-Stage Voltage -2 0.8 V On-Stage Voltage 2.4 18 V ON/OFF Control (Option N) Off-Stage Voltage 2.4 18 V On-Stage Voltage -2 0.8 V ON/OFF Control (Either Option) Figures A & B Pull-up Voltage Vin/4.25 17.7 V Pull-up Resistance 33 k Across Pins 8 & 4; Figure C; Figure 27 Output Voltage Trim Range -20 +10 % Across Pins 8 & 4; Figure 27 Output Over-Voltage Protection 117 122 127 % Over full temp range; % of nominal Vout Over-Tempperature Shutdown 125 C Average PCB Temperature Load Current Scale Factor 10 C Load Current Scale Factor 1000 See Output Load Current app. note on our web RELIABILITY CHARACTERISTICS Calculated MTBF (Telcordia) 2.50 106 Hrs. TR-NWT-000332; 80% load, 300LFM, 40C Ta Calculated MTBF (MIL-217) 1.56 106 Hrs. MIL-HDBK-217F; 80% load, 300LFM, 40C Ta Field Demonstrated MTBF 106 Hrs. See our website for details Note 1: For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Higher values of isolation capacitance can be added external to the module. Product # PQ40150QGx07 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 5 Input: Output: Current: Package: Technical Figures 18-75V 15V 6.25A Quarter-brick 92 100 95 91 85 Efficiency (%) Efficiency (%) 90 80 75 70 18 Vin 89 25 C 88 48 Vin 65 90 40 C 55 C 75 Vin 60 0 1 2 3 4 Load Current (A) 5 6 87 100 7 Figure 1: Efficiency at nominal output voltage vs. load current for 18V, 48V and 75V input at 25C. 200 Air Flow (LFM) 300 400 Figure 2: Efficiency at nominal output voltage and 60% rated power vs. airflow rate for ambient air temperatures of 25C, 40C, and 55C (nominal input voltage, 48V input). 14 7 10 Power Dissipation (W) Power Dissipation (W) 12 8 6 4 18 Vin 2 6 5 4 25 C 40 C 48 Vin 55 C 75 Vin 0 0 1 2 3 4 Load Current (A) 5 6 3 100 7 Figure 3: Power dissipation at nominal output voltage vs. load current for 18V, 48V and 75V input at 25C. 200 Air Flow (LFM) 300 400 Figure 4: Power dissipation at nominal output voltage and 60% rated power vs. airflow rate for ambient air temperatures of 25C, 40C, and 55C (nominal input voltage, 48V input). 8 7 Iout (A) 6 5 4 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 3 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 2 0 25 40 55 70 85 Ambient Air Temperature (C) Figure 5: Maximum output power derating curves vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM with air flowing across the converter from pin 3 to pin 1 (24V input). Product # PQ40150QGx07 Phone 1-888-567-9596 Figure 6: Thermal plot of converter at 6.7 amp load current with 55C air flowing at the rate of 200 LFM. Air is flowing across the converter sideways from pin 3 to pin 1 (24V input). www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 6 Input: Output: Current: Package: Technical Figures 18-75V 15V 6.25A Quarter-brick 7 6 Iout (A) 5 4 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 3 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 2 0 25 40 55 70 85 Ambient Air Temperature (C) Figure 7: Maximum output power derating curves vs. ambient air temperature for airflow rates of 0 LFM through 400 LFM with air flowing from pin 3 to pin 1 (48V input). Figure 8: Thermal plot of converter at 25 amp load current with 55C air flowing at the rate of 200 LFM. Air is flowing across the converter sideways from pin 3 to pin 1 (48V input). 8 7 Iout (A) 6 5 4 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 3 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 2 0 25 40 55 70 85 Ambient Air Temperature (C) Figure 9: Maximum output power-derating curves vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM with air flowing from input to output (24V input). Figure 10: Thermal plot of converter at 6.7 amp load current with 85C air flowing at the rate of 200 LFM. Air is flowing across the converter from input to output (24V input). 7 6 Iout (A) 5 4 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 3 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 2 0 25 40 55 70 85 Ambient Air Temperature (C) Figure 11: Maximum output power-derating curves vs. ambient air temperature for airflow rates of 100 LFM through 400 LFM with air flowing from input to output (48V input). Product # PQ40150QGx07 Phone 1-888-567-9596 Figure 12: Thermal plot of converter at 6.2 amp load current with 85C air flowing at the rate of 200 LFM. Air is flowing across the converter from input to output (48V input). www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 7 Input: Output: Current: Package: Technical Figures 18-75V 15V 6.25A Quarter-brick Figure 13: Turn-on transient at full load (resistive load) (4 ms/div). Input voltage pre-applied. Ch 1: Vout (5V/div). Ch 2: ON/OFF input (5V/div). Figure 14:Turn-on transient at zero load (4 ms/div). Ch 1: Vout (5V/div). Ch 2: ON/OFF input (5V/div). Figure 15: Output voltage response to step-change in load current (50%-75%50% of Iout(max); dI/dt = 0.1A/ s). Load cap: 10 F, 100 m ESR tantalum cap and 1 F ceramic cap. Ch 1: Vout (500mV/div), Ch 2: Iout (2A/div). Figure 16: Output voltage response to step-change in load current (50%-75%50% of Iout(max): dI/dt = 5A/s). Load cap: 470 F, 30m ESR tantalum cap and 1F ceramic cap. Ch 1: Vout (200mV/div), Ch 2: Iout (2A/div). See Fig. 19 10 H source impedance See Fig. 18 See Fig. 20 iS VSOURCE iC 47 F, <1 ESR electrolytic capacitor DC/DC Converter VOUT 1 F 10 F, ceramic 100m ESR capacitor tantalum capacitor Figure 17: Test set-up diagram showing measurement points for Input Terminal Ripple Current (Fig 18), Input Reflected Ripple Current (Fig 19) and Output Voltage Ripple (Fig 20). Product # PQ40150QGx07 Phone 1-888-567-9596 Figure 18: Input Terminal Ripple Current, ic, at full rated output current and nominal input voltage with 10H source impedance and 47F electrolytic capacitor (200mA/div). See Figure 17. www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 8 Input: Output: Current: Package: Technical Figures Figure 19: Input reflected ripple current, is, through a 10 H source inductor at nominal input voltage and rated load current (10mA/div). See Figure 17. 18-75V 15V 6.25A Quarter-brick Figure 20: Output voltage ripple at nominal input voltage and rated load current (20mV/div). Load capacitance: 1F ceramic capacitor and 10F tantalum capacitor. Bandwidth: 20MHz. See Figure 17. 16 15 Output Voltage (V) 14 13 12 11 35 Vin 10 48 Vin 9 75 Vin 8 0 1 2 3 4 5 Load Current (A) 6 7 8 9 Figure 21: Output voltage vs. load current showing typical current limit curves and converter shutdown points. Figure 22: Load current (5A/div) as a function of time when the converter attempts to turn on into a 10 mW short circuit. Top trace (40ms/div) is an expansion of the on-time portion of the bottom trace. 1 -10 0.1 0.01 18 Vin 0.001 48 Vin 75 Vin 0.0001 Forward Transmission (dB) Output Impedance (ohms) -20 -30 -40 -50 -60 -70 -80 18 Vin -90 48 Vin -100 75 Vin -110 10 100 1,000 Hz 10,000 100,000 1,000,000 Figure 23: Magnitude of incremental output impedance (Zout = vout/iout) for minimum, nominal, and maximum input voltage at full rated power. Product # PQ40150QGx07 Phone 1-888-567-9596 10 100 1,000 Hz 10,000 100,000 Figure 24: Magnitude of incremental forward transmission (FT = vout/vin) for minimum, nominal, and maximum input voltage at full rated power. www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 9 Input: Output: Current: Package: 18-75V 15V 6.25A Quarter-brick 100 -40 -50 Input Impedance (ohms) Reverse Transmission (dB) -45 -55 -60 -65 -70 -75 18 Vin -80 10 1 18 Vin 48 Vin 48 Vin -85 75 Vin 75 Vin 0.1 -90 10 100 1,000 Hz 10,000 100,000 10 1,000,000 Figure 25: Magnitude of incremental reverse transmission (RT = iin/iout) for minimum, nominal, and maximum input voltage at full rated power. 100 1,000 10,000 100,000 Hz Figure 26: Magnitude of incremental input impedance (Zin = vin/iin) for minimum, nominal, and maximum input voltage at full rated power. 12 11 Vout Trim-up (%) 10 9 8 7 6 5 +80 C 4 +25 C 3 2 23.0 -40 C 22.5 22.0 21.5 21.0 20.5 20.0 19.5 19.0 18.5 18.0 Input Voltage (V) Figure 27: Achievable trim-up percentage vs. input voltage at +85C, +25C and -40C (all at full load). Full trim-up percentage is achieved at loads of 50% or less across full temperature and input voltage range. Product # PQ40150QGx07 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 10 Input: Output: Current: Package: Application Section 18-75V 15V 6.25A Quarter-brick BASIC OPERATION AND FEATURES CONTROL FEATURES The PowerQor series converter uses a two-stage power conversion topology. The first stage is a buck-converter that keeps the output voltage constant over variations in line, load, and temperature. The second stage uses a transformer to provide the functions of input/output isolation and voltage stepdown to achieve the low output voltage required. REMOTE ON/OFF (Pin 2): The ON/OFF input, Pin 2, permits the user to control when the converter is on or off. This input is referenced to the return terminal of the input bus, Vin(-). There are two versions of the converter that differ by the sense of the logic used for the ON/OFF input. Both the first stage and the second stage switch at a fixed frequency for predictable EMI performance. Rectification of the transformer's output is accomplished with synchronous rectifiers. These devices, which are MOSFETs with a very low on-state resistance, dissipate far less energy than Schottky diodes. This is the primary reason that the PowerQor converter has such high efficiency, even at very low output voltages and very high output currents. Dissipation throughout the converter is so low that it does not require a heatsink for operation. Since a heatsink is not required, the PowerQor converter does not need a metal baseplate or potting material to help conduct the dissipated energy to the heatsink. The PowerQor converter can thus be built more simply and reliably using high yield surface mount techniques on a PCB substrate. The PowerQor series of half-brick and quarter-brick converters uses the industry standard footprint and pin-out configuration. ON/OFF ON/OFF Vin(_) Vin(_) Remote Enable Circuit Pin 7 should be connected to Vout(+) and Pin 5 should be connected to Vout(-) at the point on the board where regulation is desired. A remote connection at the load can adjust for a voltage drop only as large as that specified in this datasheet, that is [Vout(+) - Vout(-)] - [Vsense(+) - Vsense(-)] < Sense Range % x Vout Pins 7 and 5 must be connected for proper regulation of the output voltage. If these connections are not made, the converter will deliver an output voltage that is slightly higher than its specified value. Note: the output over-voltage protection circuit senses the voltage across the output (pins 8 and 4) to determine when it should trigger, not the voltage across the converter's sense leads (pins 7 and 5). Therefore, the resistive drop on the board should be small enough so that output OVP does not trigger, even during load transients. Positive Logic (Permanently Enabled) 5V 5V 162k 50k TTL ON/OFF Vin(_) Vin(_) 100pF 50k Vin(_) Direct Logic Drive Figure A: Various circuits for driving the ON/OFF pin. Product # PQ40150QGx07 Vin(+) ON/OFF TTL/ CMOS Open Collector Enable Circuit REMOTE SENSE(+) (Pins 7 and 5): The SENSE(+) inputs correct for voltage drops along the conductors that connect the converter's output pins to the load. Vin(_) Negative Logic (Permanently Enabled) ON/OFF ON/OFF In the positive logic version, the ON/OFF input is active high (meaning that a high turns the converter on). In the negative logic version, the ON/OFF signal is active low (meaning that a low turns the converter on). Figure A details five possible circuits for driving the ON/OFF pin. Figure B is a detailed look of the internal ON/OFF circuitry. Phone 1-888-567-9596 www.synqor.com Figure B: Internal ON/OFF pin circuitry Doc.# 005-2QG157D Rev. C 11/27/12 Page 11 Input: Output: Current: Package: Application Section OUTPUT VOLTAGE TRIM (Pin 6): The TRIM input permits the user to adjust the output voltage across the sense leads up or down according to the trim range specifications. To decrease the output voltage, the user should connect a resistor between Pin 6 and Pin 5 (SENSE(-) input). For a desired decrease of the nominal output voltage, the value of the resistor should be Rtrim-down = 511 - 10.22 (kW) D% ( ) where Vnominal - Vdesired Vnominal D% = x 100% To increase the output voltage, the user should connect a resistor between Pin 6 and Pin 7 (SENSE(+) input). For a desired increase of the nominal output voltage, the value of the resistor should be Rtrim- = up where ( 5.11VOUT(100+D%) _ 511 _ 10.22 1.225D% D% ) (kW) VOUT = Nominal Output Voltage Figure C graphs the relationship between the trim resistor value and Rtrim-up and Rtrim-down, showing the total range the output voltage can be trimmed up or down. Trim Resistance (kOhms) Total DC Variation of Vout: For the converter to meet its full specifications, the maximum variation of the DC value of Vout, due to both trimming and remote load voltage drops, should not be greater than that specified for the output voltage trim range. PROTECTION FEATURES Input Under-Voltage Lockout: The converter is designed to turn off when the input voltage is too low, helping avoid an input system instability problem, described in more detail in the application note titled "Input System Instability". The lockout circuitry is a comparator with DC hysteresis. When the input voltage is rising, it must exceed the typical Turn-On Voltage Threshold value (listed on the specification page) before the converter will turn on. Once the converter is on, the input voltage must fall below the typical Turn-Off Voltage Threshold value before the converter will turn off. Output Current Limit: The maximum current limit remains constant as the output voltage drops. However, once the impedance of the short across the output is small enough to make the output voltage drop below the specified Output DC Current-Limit Shutdown Voltage, the converter turns off. The converter then enters a "hiccup mode" where it repeatedly turns on and off at a 5 Hz (nominal) frequency with a 5% duty cycle until the short circuit condition is removed. This prevents excessive heating of the converter or the load board. Output Over-Voltage Limit: If the voltage across the output pins exceeds the Output Over-Voltage Protection threshold, the converter will immediately stop switching. This prevents damage to the load circuit due to 1) excessive series resistance in output current path from converter output pins to sense point, 2) a release of a short-circuit condition, or 3) a release of a current limit condition. Load capacitance determines exactly how high the output voltage will rise in response to these conditions. After 200 ms the converter will automatically restart. 100,000.0 10,000.0 1,000.0 100.0 10.0 18-75V 15V 6.25A Quarter-brick 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 % Increase in Vout % Decrease in Vout Figure C: Trim Graph Note: the TRIM feature does not affect the voltage at which the output over-voltage protection circuit is triggered. Trimming the output voltage too high may cause the over-voltage protection circuit to engage, particularly during transients. Over-Temperature Shutdown: A temperature sensor on the converter senses the average temperature of the module. The thermal shutdown circuit is designed to turn the converter off when the temperature at the sensed location reaches the Over-Temperature Shutdown value. It will allow the converter to turn on again when the temperature of the sensed location falls by the amount of the Over-Temperature Shutdown Restart Hysteresis value. It is not necessary for the user to add capacitance at the Trim pin. The node is internally bypassed to eliminate noise. Product # PQ40150QGx07 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 12 Input: Output: Current: Package: Application Section APPLICATION CONSIDERATIONS Input System Instability: This condition can occur because any DC/DC converter appears incrementally as a negative resistance load. A detailed application note titled "Input System Instability" is available on the SynQor website which provides an understanding of why this instability arises, and shows the preferred solution for correcting it. 18-75V 15V 6.25A Quarter-brick Input Filtering and External Capacitance: Figure E below provides a diagram showing the internal input filter components. This filter dramatically reduces input terminal ripple current, which otherwise could exceed the rating of an external electrolytic input capacitor. The recommended external input capacitance is specified in the "Input Characteristics" section. More detailed information is available in the application note titled "EMI Characteristics" on the SynQor website. Application Circuits: Figure D below provides a typical circuit diagram which details the input filtering and voltage trimming. Vout(+) Vin(+) Vin External Input Filter Electrolytic Capacitor 47F Vsense(+) Rtrim-up Trim ON/OFF or Rtrim-down Vsense(_) Vin(_) Cload Iload Vout(_) Figure D: Typical application circuit (negative logic unit, permanently enabled). L Vin(+) C Vin(_) Figure E: Internal Input Filter Diagram (component values listed on page 3). Product # PQ40150QGx07 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 13 Input: Output: Current: Package: Application Section 18-75V 15V 6.25A Quarter-brick Startup Inhibit Period: The Startup Inhibit Period ensures that the converter will remain off for approximately 200ms when it is shut down for any reason. When an output short is present, this generates a 5Hz "hiccup mode," which prevents the converter from overheating. In all, there are seven ways that the converter can be shut down, initiating a Startup Inhibit Period: Before time t0, when the input voltage is below the UVL threshold, the unit is disabled by the Input Under-Voltage Lockout feature. When the input voltage rises above the UVL threshold, the Input Under-Voltage Lockout is released, and a Startup Inhibit Period is initiated. At the end of this delay, the ON/OFF pin is evaluated, and since it is active, the unit turns on. * Input Under-Voltage Lockout At time t1, the unit is disabled by the ON/OFF pin, and it cannot be enabled again until the Startup Inhibit Period has elapsed. * Input Over-Voltage Shutdown (not present in Quarter-brick) * Output Over-Voltage Protection When the ON/OFF pin goes high after t2, the Startup Inhibit Period has elapsed, and the output turns on within the typical Turn-On Time. * Over Temperature Shutdown * Current Limit * Short Circuit Protection * Turned off by the ON/OFF input Figure F shows three turn-on scenarios, where a Startup Inhibit Period is initiated at t0, t1, and t2: RoHS Compliance: The EU led RoHS (Restriction of Hazardous Substances) Directive bans the use of Lead, Cadmium, Hexavalent Chromium, Mercury, Polybrominated Biphenyls (PBB), and Polybrominated Diphenyl Ether (PBDE) in Electrical and Electronic Equipment. This SynQor product is 6/6 RoHS compliant. For more information please refer to SynQor's RoHS addendum available at our RoHS Compliance / Lead Free Initiative web page or e-mail us at rohs@synqor.com. Vin Under-Voltage Lockout Turn-On Threshold ON/OFF (pos logic) ON OFF OFF ON ON 8ms (typical turn on time) Vout 200ms (typical start-up inhibit period) t1 t0 200ms 200ms t2 t Figure F: Startup Inhibit Period (turn-on time not to scale) Product # PQ40150QGx07 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 14 Input: Output: Current: Package: Standards and Qualifications Parameter 18-75V 15V 6.25A Quarter-brick Notes & Conditions STANDARDS COMPLIANCE UL 60950-1:2007 CAN/CSA-C22.2 No. 60950-1:2007 EN60950-1/A12:2011 IEC 61000-4-2 Basic insulation ESD test, 8 kV - NP, 15 kV air - NP (Normal Performance) Note: An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new releases or download from the SynQor website. Parameter QUALIFICATION TESTING Life Test Vibration Mechanical Shock Temperature Cycling Power/Thermal Cycling Design Marginality Humidity Solderability Product # PQ40150QGx07 # Units 32 5 5 10 5 5 5 15 pins Phone 1-888-567-9596 Test Conditions 95% rated Vin and load, units at derating point, 1000 hours 10-55 Hz sweep, 0.060" total excursion, 1 min./sweep, 120 sweeps for 3 axis 100g minimum, 2 drops in x, y and z axis -40 C to 100 C, unit temp. ramp 15 C/min., 500 cycles Toperating = min to max, Vin = min to max, full load, 100 cycles Tmin-10 C to Tmax+10 C, 5 C steps, Vin = min to max, 0-105% load 85 C, 95% RH, 1000 hours, continuous Vin applied except 5 min/day MIL-STD-883, method 2003 www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 15 Input: Output: Current: Package: Ordering Information PART NUMBERING SYSTEM 18-75V 15V 6.25A Quarter-brick ORDERING INFORMATION The part numbering system for SynQor's dc-dc converters follows the format shown in the example below. PQ 4 0 1 5 0 Q G A 0 7 N R S Options (see Ordering Information) Output Current The tables below show the valid model numbers and ordering options for converters in this product family. When ordering SynQor converters, please ensure that you use the complete 15 character part number consisting of the 12 character base part number and the additional characters for options. Add "-G" to the model number for 6/6 RoHS compliance. The following options must be included in place of the w x y z spaces in the model numbers listed above. Thermal Design Performance Level Thermal Design Package Size Output Voltage Options Description: w x y z Enable Logic Pin Style A - Open Frame B - Baseplated Input Voltage N - Negative P - Positive Product Family The first 12 characters comprise the base part number and the last 3 characters indicate available options. The "-G" suffix indicates 6/6 RoHS compliance. K - 0.110" N - 0.145" R - 0.180" Y - 0.250" Feature Set S - Standard Not all combinations make valid part numbers, please contact SynQor for availability. See the Product Summary web page for more options. Application Notes A variety of application notes and technical white papers can be downloaded in pdf format from our website. RoHS Compliance: The EU led RoHS (Restriction of Hazardous Substances) Directive bans the use of Lead, Cadmium, Hexavalent Chromium, Mercury, Polybrominated Biphenyls (PBB), and Polybrominated Diphenyl Ether (PBDE) in Electrical and Electronic Equipment. This SynQor product is 6/6 RoHS compliant. For more information please refer to SynQor's RoHS addendum available at our RoHS Compliance / Lead Free Initiative web page or e-mail us at rohs@synqor.com. Model Number Input Voltage Range Output Voltage Max Output Current PQ40150QGw07xyz PQ40120QGw08xyz PQ40080QGw09xyz PQ40050QGw20xyz PQ40033QGw25xyz 18-75V 18-75V 18-75V 18-75V 18-75V 15V 12 V 8.0 V 5.0 V 3.3 V 6.67A 8.33 A 9.0A 20 A 25 A PATENTS SynQor holds the following U.S. patents, one or more of which apply to each product listed in this document. Additional patent applications may be pending or filed in the future. Contact SynQor for further information: Phone: Toll Free: Fax: E-mail: Web: Address: Product # PQ40150QGx07 978-849-0600 888-567-9596 978-849-0602 power@synqor.com www.synqor.com 155 Swanson Road Boxborough, MA 01719 USA Phone 1-888-567-9596 5,999,417 6,222,742 6,545,890 6,577,109 6,594,159 6,731,520 6,894,468 6,896,526 6,927,987 7,050,309 7,072,190 7,085,146 7,119,524 7,269,034 7,272,021 7,272,023 7,558,083 7,564,702 7,765,687 7,787,261 8,023,290 8,149,597 Warranty SynQor offers a three (3) year limited warranty. Complete warranty information is listed on our website or is available upon request from SynQor. Information furnished by SynQor is believed to be accurate and reliable. However, no responsibility is assumed by SynQor for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SynQor. www.synqor.com Doc.# 005-2QG157D Rev. C 11/27/12 Page 16