GP1A05AJ000F Series GP1A05AJ000F Series Gap : 5mm, Slit : 0.5mm *OPIC Output Transmissive Photointerrupter with Connector Description Agency approvals/Compliance GP1A05AJ000F Series are standard, OPIC output, transmissive photointerrupters with opposing emitter and detector in a case, providing non-contact sensing. For this family of devices, the emitter and detector are inserted in a case, and a 3-pin connector is included to allow remote-mount or off-board designs. 1. Compliant with RoHS directive Applications 1. General purpose detection of object presence or motion. 2. Example: PPC, FAX, Printer Features 1. Transmissive with OPIC output 2. Highlights : * Includes additional screw fixing holes * Positioning Pin to prevent misalignment 3. Key Parameters: * Gap Width : 5mm * Slit Width (detector side) : 0.5mm * Package : 34x18x11mm (without connector and positloning pin) * Connector : GP1A05AJ000F ; Tyco Electronics AMP K.K. (PN : 171825-3) GP1A05A2J00F ; J.S.T. Mfg Co., Ltd. (PN : B3P-SHF-IAA (LF)) GP1A05A5J00F ; Molex-Japan Co., Ltd. (PN : 5267-03A) * Output Type : High when the object is present with Pullup Resistor 4. Lead free and RoHS directive compliant * "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signalprocessing Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 1 Sheet No.: D3-A04501EN Date Oct. 3. 2005 (c) SHARP Corporation GP1A05AJ000F Series Internal Connection Diagram 1 Voltage regulator 2 Amp. 1 3 2 3 VCC GND VOUT Truth table (In case of external addition pull-up resistance to VOUT terminal) Condition Light beam interrupted Light beam uninterrupted Output High Low Outline Dimensions (Unit : mm) GP1A05AJ000F GP1A05A2J00F 30.1 Depth 2 2 Model No. 2 2 . 4 3.5 1 2 3 2 . 0 2 . 4 1 2 3 05 . 0 05 3.5 30.1 Depth2 2 Model No. 7 7 3.5 15 5 5 Slit width0.50.1 10.5 Slit width 0.50.1 Protrusion of connector from holder : Max.1 3 10.41 Model indicator Y Z 1 D QD A QZ 5.51 QD 3.5 QB Date code indicator (month) 110.1 QA 120.1 0 5 2 3 4 E 110.1 11 QB B Date code (Year) 8 9 X 11 8 9 X QZ 2 3 4 QA 0 5 +0 0.1 - Y Z 1 D E A 4 B 9.21 34 Date code (Year) 5 6 7 +0 0.1 - 4 Model indicator Connector : B3P-SHF-1AA (LF) (J.S.T. MFG. CO., LTD.) C0.5 5 6 7 3 C0.5 120.1 5.51 7.5 7.5 10.5 Connector : 171825-3 (Tyco Electronics AMP K.K.) 34 3.5 3.5 15 5 5 Date code indicator (month) * Unspecified tolerance shall be as follows ; * Unspecified tolerance shall be as follows ; Dimensions(d) Tolerance less than 4 0.2 4 or more less than 16 0.3 16 or more 0.5 Dimensions(d) Tolerance less than 4 0.2 4 or more less than 16 0.3 16 or more 0.5 Product mass : approx. 3.0g Product mass : approx. 3.0g Connector terminal plating material : Sn Connector terminal plating material : Sn Sheet No.: D3-A04501EN 2 GP1A05AJ000F Series (Unit : mm) GP1A05A5J00F 2 . 0 2 4. 05 3.5 30.1 Depth 2 2 Model No. 7 3.5 15 5 5 3 7.5 10.5 Slit width 0.50.1 C0.5 4 Model indicator Connector : 5267-03A (MOLEX-JAPAN CO., LTD.) 3 2 1 34 5.51 8 9 X A QZ 2 3 4 QA QB QD 110.1 0 5 11 Y Z 1 D E 3.5 5.91 5 6 7 +0 0.1 - B Date code (Year) 120.1 Date code indicator (month) * Unspecified tolerance shall be as follows ; Dimensions(d) Tolerance less than 4 0.2 4 or more less than 16 0.3 16 or more 0.5 Product mass : approx. 3.0g Connector terminal plating material : Sn Sheet No.: D3-A04501EN 3 GP1A05AJ000F Series Date code Year of production Last two digits of Christian year. Month of production Month Mark 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 X 11 Y 12 Z Country of origin Japan or Philippines (Indicated on the packing case) Sheet No.: D3-A04501EN 4 GP1A05AJ000F Series Absolute Maximum Ratings Parameter Symbol Supply GP1A05AJ000F VCC voltage GP1A05A2J00F/GP1A05A5J00F *1 Output voltage VOUT *2 Low level output current IOL *3 Operating temperature Topr *3 Storage temperature Tstg Rating -0.5 to +10 -0.5 to +8 -0.5 to +28 50 -20 to +75 -40 to +85 (Ta=25C) Unit V V mA C C 1 Collector-emitter voltage of output transistor. 2 Collector current of output transistor, refer to Fig.1. 3 The connector should be plugged in/out at normal temperature. Electro-optical Characteristics Parameter Low level supply current Low level output voltage High level supply current High level output voltage *4 Response frequency Operating supply voltage Rise time *5 Response time Fall time Conditions Light beam uninterrupted Light beam uninterrupted, IOL=16mA Light beam interrupted Light beam interrupted, RL=47k RL=47k - RL=280 MIN. - - - VCCx0.9 - 4.5 - - 4 Response frequency is measured with the disk shown below being rotated. 5 Refer to Fig.7. (Unit : mm) Disk 0.5 0.5 2.0 Symbol ICCL VOL ICCH VOH f VCC tr tf (VCC=5V, Ta=25C) TYP. MAX. Unit 30 mA - 0.35 V - 30 mA - V - - 3 000 Hz - 5.5 V - 0.1 0.5 s 0.05 0.5 s Sheet No.: D3-A04501EN 5 GP1A05AJ000F Series Fig.2 Low Level Output Voltage vs. Low Level Output Current Fig.1 Low Level Output Current vs. Ambient Temperature 1.0 50 Low level output voltage VOL (V) Low level output current IOL (mA) 60 40 30 20 16.6 10 VCC=5V Ta=25C 0.1 0.01 0 -20 0 25 50 75 1 100 10 100 Low level output current IOL (mA) Ambient temperature Ta (C) Fig.3 Low Level Output Voltage vs. Ambient Temperature Fig.4 Supply Current vs. Supply Voltage 30 0.6 0.5 Supply current ICC (mA) Low level output voltage VOL (V) VCC=5V 0.4 IOL=30mA 0.3 0.2 16mA 0.1 20 Ta=-20C ICCL 10 ICCH +25C +75C Ta=-20C, +25C, +75C 5mA 0 0 -25 0 25 50 75 4.5 100 5.0 5.5 Supply voltage VCC (V) Ambient temperature Ta (C) Fig.5 Detecting Position Characteristics (1) Fig.6 Detecting Position Characteristics (2) (Detecting position : d=3.50.3) (Detecting position : h=3+2 -1.5 ) VCC=5V Ta=25C RL=47k VCC=5V Ta=25C RL=47k Output "High" Output "High" Shield h 0 d 0 Shield Sensor Sensor Output "Low" 0 1 2 3 4 5 6 0 7 Shield moving distance d (mm) 1 2 3 4 5 6 Output "Low" 7 Shield moving distance h (mm) Sheet No.: D3-A04501EN 6 GP1A05AJ000F Series Fig.7 Test Circuit for Response Time Input VCC RD Input RL Output 10% Output 90% ts td tr tf Remarks : Please be aware that all data in the graph are just for reference and not for guarantee. Sheet No.: D3-A04501EN 7 GP1A05AJ000F Series Design Considerations Design guide 1) Prevention of detection error To prevent photointerrupter from faulty operation caused by external light, do not set the detecting face to the external light. 2) In order to stabilize power supply line, connect a by-pass capacitor of more than 0.01F between VCC and GND near the device. 3) When the sensor is connected with long wire, noise might be on the signal from the sensor while it is going through the wire. To avoid this problem, please evaluate the sensor under actual usage condition to make sure that the system works fine. 4) Position of opaque board Opaque board shall be installed at place 5mm or more from the top of elements. (Example) 5mm or more 5) Screw tightening torque The tightening torque for screwing should be 0.6Nm or less. This product is not designed against irradiation and incorporates non-coherent IRED. Parts This product is assembled using the below parts. * Photodetector (qty. : 1) [Using a silicon photodiode as light detecting portion, and a bipolar IC as signal processing circuit] Category Maximum Sensitivity wavelength (nm) Sensitivity wavelength (nm) Response time (s) Photodiode 900 400 to 1 200 3 * Photo emitter (qty. : 1) Category Material Maximum light emitting wavelength (nm) I/O Frequency (MHz) Infrared emitting diode (non-coherent) Gallium arsenide (GaAs) 950 0.3 Sheet No.: D3-A04501EN 8 GP1A05AJ000F Series * Material Case Connector terminal finish Black Polcarbonate resin (UL94 HB) Sn plating * Others Laser generator is not used. Sheet No.: D3-A04501EN 9 GP1A05AJ000F Series Manufacturing Guidelines Notes of cleaning Please carry out neither the immersion cleaning nor the ultrasonic cleaning to avoid the solvent residue inside the case. When necessary, dust and stain shall clean by air-blow or wipe off by soft cloth soaked in cleaning agent. The cleaning agent used to wipe off must use only the following kind. Ethyl alcohol, Methyl alcohol and Isopropyl alcohol. Presence of ODC This product shall not contain the following materials. And they are not used in the production process for this product. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC). *Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated diphenyl ethers (PBDE). Sheet No.: D3-A04501EN 10 GP1A05AJ000F Series Package specification Case package Package materials Anti-static plastic bag : Polyethtylene Moltopren : Urethane Partition : Corrugated fiberboard Packing case : Corrugated fiberboard Package method 75 pcs of products shall be packaged in a plastic bag, Ends shall be sealed by stapler. The bottom ot the packing case is covered with moltopren, and the partition is set in the packing case. Each partition should have 1 plastic bag. Moltopren should be located after all product are settled (1 packing conteains 150 pcs). Packing composition Moltopren Plastic bag Packing case Sheet No.: D3-A04501EN 11 GP1A05AJ000F Series Important Notices * The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). * Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. * If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. * Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection * This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. * Contact and consult with a SHARP representative if there are any questions about the contents of this publication. Sheet No.: D3-A04501EN [H170] 12