GS74116ATP/J/X SOJ, TSOP, FP-BGA Commercial Temp Industrial Temp 256K x 16 4Mb Asynchronous SRAM 6, 7, 8, 10, 12 ns 3.3 V VDD Center VDD and VSS Features * Fast access time: 6, 7, 8, 10, 12 ns * CMOS low power operation: 170/150/130/105/95 mA at minimum cycle time * Single 3.3 V power supply * All inputs and outputs are TTL-compatible * Byte control * Fully static operation * Industrial Temperature Option: -40 to 85C * Package line up J: 400 mil, 44-pin SOJ package TP: 400 mil, 44-pin TSOP Type II package X: 6 mm x 10 mm Fine Pitch Ball Grid Array package Description The GS74116A is a high speed CMOS Static RAM organized as 262,144 words by 16 bits. Static design eliminates the need for external clocks or timing strobes. The GS operates on a single 3.3 V power supply and all inputs and outputs are TTLcompatible. The GS74116A is available in a 6 x 10 mm Fine Pitch BGA package, 400 mil SOJ and 400 mil TSOP Type-II packages. Pin Descriptions Symbol SOJ 256K x 16-Pin Configuration (Package J) A4 A3 A2 A1 A0 CE DQ1 DQ2 DQ3 DQ4 VDD 1 2 3 4 5 6 7 8 9 10 11 12 VSS Top view 44-pin SOJ 13 14 15 DQ5 DQ6 DQ7 DQ8 WE A15 A14 A13 A12 A16 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 16 17 18 27 26 25 24 23 19 20 21 22 A5 A6 A7 OE UB LB DQ16 DQ15 DQ14 DQ13 VSS VDD DQ12 DQ11 DQ10 DQ9 NC A8 A9 A10 A11 A17 FP-BGA 256K x 16 Bump Configuration (Package X) 1 2 3 4 5 6 A LB OE A0 A1 A2 NC B DQ16 UB A3 A4 CE DQ1 C DQ14 DQ15 A5 A6 DQ2 DQ3 Description A0-A17 Address input DQ1-DQ16 Data input/output CE Chip enable input LB Lower byte enable input (DQ1 to DQ8) UB Upper byte enable input (DQ9 to DQ16) D VSS DQ13 A17 A7 DQ4 VDD WE Write enable input E VDD DQ12 NC A16 DQ5 VSS OE Output enable input F DQ11 DQ10 A8 A9 DQ7 DQ6 VDD +3.3 V power supply G DQ9 NC A10 A11 WE DQ8 VSS Ground H NC A12 A13 A14 A15 NC NC No connect 6 x 10 mm Bump Pitch Rev: 1.02 3/2002 1/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X Top View TSOP-II 256K x 16 Pin Configuration (Package TP) A4 A3 A2 A1 A0 CE DQ1 DQ2 DQ3 DQ4 VDD VSS DQ5 DQ6 DQ7 DQ8 WE A15 A14 A13 A12 A16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Top view 44 pin TSOP II 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A5 A6 A7 OE UB LB DQ16 DQ15 DQ14 DQ13 VSS VDD DQ12 DQ11 DQ10 DQ9 NC A8 A9 A10 A11 A17 Block Diagram A0 Address Input Buffer Row Decoder Column Decoder A17 CE WE Control OE _____ UB LB _____ Rev: 1.02 3/2002 Memory Array I/O Buffer DQ1 DQ16 2/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X Truth Table CE OE WE LB UB DQ1 to DQ8 DQ9 to DQ16 VDD Current H X X X X Not Selected Not Selected ISB1, ISB2 L L Read Read L H Read High Z H L High Z Read L L Write Write L H Write Not Write, High Z H L Not Write, High Z Write L L L H X L L H H X X High Z High Z L X X H H High Z High Z IDD Note: X: "H" or "L" Absolute Maximum Ratings Parameter Symbol Rating Unit Supply Voltage VDD -0.5 to +4.6 V Input Voltage VIN -0.5 to VDD +0.5 ( 4.6 V max.) V Output Voltage VOUT -0.5 to VDD +0.5 ( 4.6 V max.) V Allowable power dissipation PD 0.7 W Storage temperature TSTG -55 to 150 o C Note: Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation shall be restricted to Recommended Operating Conditions. Exposure to higher than recommended voltages for extended periods of time could affect device reliability. Rev: 1.02 3/2002 3/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X Recommended Operating Conditions Parameter Symbol Min Typ Max Unit Supply Voltage for -7/-8/-10/-12 VDD 3.0 3.3 3.6 V Supply Voltage for -6 VDD 3.135 3.3 3.6 V Input High Voltage VIH 2.0 -- VDD +0.3 V Input Low Voltage VIL -0.3 -- 0.8 V Ambient Temperature, Commercial Range TAc 0 -- 70 o Ambient Temperature, Industrial Range TAI -40 -- 85 oC C Note: 1. Input overshoot voltage should be less than VDD +2 V and not exceed 20 ns. 2. Input undershoot voltage should be greater than -2 V and not exceed 20 ns. Capacitance Parameter Symbol Test Condition Max Unit Input Capacitance CIN VIN = 0 V 5 pF Output Capacitance COUT VOUT = 0 V 7 pF Notes: 1. Tested at TA = 25C, f = 1 MHz 2. These parameters are sampled and are not 100% tested. DC I/O Pin Characteristics Parameter Symbol Test Conditions Min Max Input Leakage Current IIL VIN = 0 to VDD - 1 uA 1 uA Output Leakage Current ILO Output High Z VOUT = 0 to VDD -1 uA 1 uA Output High Voltage VOH IOH = -4 mA 2.4 -- Output Low Voltage VOL ILO = +4 mA -- 0.4 V Rev: 1.02 3/2002 4/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X Power Supply Currents Parameter Symbol Test Conditions 0 to 70C -40 to 85C 6 ns 7 ns 8 ns IDD CE VIL All other inputs VIH or VIL Min. cycle time IOUT = 0 mA 170 150 130 105 Standby Current ISB1 CE VIH All other inputs VIH or VIL Min. cycle time 40 40 30 25 Standby Current ISB2 CE VDD - 0.2V All other inputs VDD - 0.2 V or 0.2 V Operating Supply Current 10 ns 12 ns 7 ns 8 ns 90 180 160 140 115 100 mA 25 50 50 40 35 35 mA 10 10 ns 12 ns Unit 6 ns 20 mA AC Test Conditions Output Load 1 Parameter Conditions Input high level VIH = 2.4 V Input low level VIL = 0.4 V 50 Input rise time tr = 1 V/ns VT = 1.4 V Input fall time tf = 1 V/ns Input reference level 1.4 V Output Load 2 Output reference level 1.4 V 3.3 V Output load Fig. 1& 2 DQ Rev: 1.02 3/2002 589 DQ Note: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted. 3. Output load 2 for tLZ, tHZ, tOLZ and tOHZ 5/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 30pF1 5pF1 434 (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X AC Characteristics Read Cycle Parameter Symbol Read cycle time -6 -7 -8 -10 -12 Unit Min Max Min Max Min Max Min Max Min Max tRC 6 -- 7 -- 8 -- 10 -- 12 -- ns Address access time tAA -- 6 -- 7 -- 8 -- 10 -- 12 ns Chip enable access time (CE) tAC -- 6 -- 7 -- 8 -- 10 -- 12 ns Byte enable access time (UB, LB) tAB -- 3 -- 3 -- 3.5 -- 4 -- 5 ns Output enable to output valid (OE) tOE -- 3 -- 3 -- 3.5 -- 4 -- 5 ns Output hold from address change tOH 3 -- 3 -- 3 -- 3 -- 3 -- ns Chip enable to output in low Z (CE) tLZ* 3 -- 3 -- 3 -- 3 -- 3 -- ns Output enable to output in low Z (OE) tOLZ* 0 -- 0 -- 0 -- 0 -- 0 -- ns Byte enable to output in low Z (UB, LB) tBLZ* 0 -- 0 -- 0 -- 0 -- 0 -- ns Chip disable to output in High Z (CE) tHZ* -- 3 -- 3.5 -- 4 -- 5 -- 6 ns Output disable to output in High Z (OE) tOHZ* -- 3 -- 3 -- 3.5 -- 4 -- 5 ns Byte disable to output in High Z (UB, LB) tBHZ* -- 3 -- 3 -- 3.5 -- 4 -- 5 ns * These parameters are sampled and are not 100% tested. Read Cycle 1: CE = OE = VIL, WE = VIH, UB and, or LB = VIL tRC Address tAA tOH Data Out Rev: 1.02 3/2002 Previous Data Data valid 6/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X Read Cycle 2: WE = VIH tRC Address tAA CE tAC tHZ tLZ tAB UB, LB tBHZ tBLZ OE tOE Data Out tOHZ Data valid tOLZ High impedance Write Cycle Parameter Symbol Write cycle time -6 -7 -8 -10 -12 Unit Min Max Min Max Min Max Min Max Min Max tWC 6 -- 7 -- 8 -- 10 -- 12 -- ns Address valid to end of write tAW 5 -- 5 -- 5.5 -- 7 -- 8 -- ns Chip enable to end of write tCW 5 -- 5 -- 5.5 -- 7 -- 8 -- ns Byte enable to end of write tBW 5 -- 5 -- 5.5 -- 7 -- 8 -- ns Data set up time tDW 3 -- 3.5 -- 4 -- 4.5 -- 6 -- ns Data hold time tDH 0 -- 0 -- 0 -- 0 -- 0 -- ns Write pulse width tWP 5 -- 5 -- 5.5 -- 7 -- 8 -- ns Address set up time tAS 0 -- 0 -- 0 -- 0 -- 0 -- ns Write recovery time (WE) tWR 0 -- 0 -- 0 -- 0 -- 0 -- ns Write recovery time (CE) tWR1 0 -- 0 -- 0 -- 0 -- 0 -- ns Output Low Z from end of write tWLZ* 3 -- 3 -- 3 -- 3 -- 3 -- ns Write to output in High Z tWHZ* -- 3 -- 3 -- 3.5 -- 4 -- 5 ns * These parameters are sampled and are not 100% tested. Rev: 1.02 3/2002 7/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X Write Cycle 1: WE control tWC Address tAW tWR OE tCW CE tBW UB, LB tAS tWP WE tDW tDH Data valid Data In tWHZ tWLZ Data Out High impedance Write Cycle 2: CE control tWC Address tAW tWR1 OE tAS tCW CE tBW UB, LB tWP WE tDW Data valid Data In Data Out Rev: 1.02 3/2002 tDH High impedance 8/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X Write Cycle 3: UB, LB control tWC Address tAW tWR1 OE tAS tCW CE tBW UB, LB tWP WE tDW Data valid Data In Data Out Rev: 1.02 3/2002 tDH High impedance 9/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X 44-Pin, 400 mil SOJ L D c HE GE 23 E 44 22 e A A1 A A2 1 Symbol y B B1 Detail A Q Dimension in inch min nom max Dimension in mm min nom max A -- -- 0.148 -- -- 3.759 A1 0.025 -- -- 0.635 -- -- A2 0.105 0.110 0.115 2.667 2.794 2.921 B -- 0.018 -- -- 0.457 -- B1 0.026 0.028 0.032 0.660 0.711 0.813 c -- 0.008 -- -- 0.203 -- D 1.120 1.125 1.130 28.44 28.58 28.70 E 0.395 0.400 0.405 10.033 10.160 10.287 e -- 0.05 -- -- 1.27 -- HE 0.435 0.440 0.445 11.049 11.176 11.303 GE 0.360 0.370 0.380 9.144 9.398 9.652 L 0.082 0.087 0.106 2.083 2.210 2.70 y -- -- 0.004 -- -- 0.102 Q o -- o o -- 7o 0 7 0 Notes: 1. Dimension D& E do not include interlead flash 2. Dimension B1 does not include dambar protrusion / intrusion 3. Controlling dimension: inches Rev: 1.02 3/2002 10/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X 44-Pin, 400 mil TSOP-II D c 22 e B y L L1 A1 A A2 1 A HE 23 E 44 Dimension in inch Dimension in mm Symbol min nom max min nom max Detail A Rev: 1.02 3/2002 Q A -- -- 0.047 -- -- 1.20 A1 0.002 -- -- 0.05 -- -- A2 0.037 0.039 0.041 0.95 1.00 1.05 B 0.01 0.014 0.018 0.25 0.35 0.45 c -- 0.006 -- -- 0.15 -- D 0.721 0.725 0.729 18.31 18.41 18.51 E 0.396 0.400 0.404 10.06 10.16 10.26 e -- 0.031 -- -- 0.80 -- HE 0.455 0.463 0.471 11.56 11.76 11.96 L 0.016 0.020 0.024 0.40 0.50 0.60 L1 -- 0.031 -- -- 0.80 -- y -- -- 0.004 -- -- 0.10 Q 0o -- 5o 0o -- 5o Notes: 1. Dimension D& E do not include interlead flash. 2. Dimension B does not include dambar protrusion/intrusion. 3. Controlling dimension: mm 11/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X 6 mm x 10 mm FP-BGA Symbol D E Pin A1 Index Top View A Unit: mm A 1.100.10 A1 0.20~0.30 fb f0.30~0.40 c 0.36(TYP) D 10.00.05 D1 5.25 E 6.00.05 E1 3.75 e 0.75(TYP) aaa 0.10 c A1 Pin A1 Index Side View aaa A B C D E F G H 1 2 3 4 5 6 fb Solder Ball e E1 e D1 Bottom View Rev: 1.02 3/2002 12/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X Ordering Information Part Number* Package Access Time Temp. Range GS74116ATP-6 400 mil TSOP-II 6 ns Commercial GS74116ATP-7 400 mil TSOP-II 7 ns Commercial GS74116ATP-8 400 mil TSOP-II 8 ns Commercial GS74116ATP-10 400 mil TSOP-II 10 ns Commercial GS74116ATP-12 400 mil TSOP-II 12 ns Commercial GS74116ATP-6I 400 mil TSOP-II 6 ns Industrial GS74116ATP-7I 400 mil TSOP-II 7 ns Industrial GS74116ATP-8I 400 mil TSOP-II 8 ns Industrial GS74116ATP-10I 400 mil TSOP-II 10 ns Industrial GS74116ATP-12I 400 mil TSOP-II 12 ns Industrial GS74116AJ-6 400 mil SOJ 6 ns Commercial GS74116AJ-7 400 mil SOJ 7 ns Commercial GS74116AJ-8 400 mil SOJ 8 ns Commercial GS74116AJ-10 400 mil SOJ 10 ns Commercial GS74116AJ-12 400 mil SOJ 12 ns Commercial GS74116AJ-6I 400 mil SOJ 6 ns Industrial GS74116AJ-7I 400 mil SOJ 7 ns Industrial GS74116AJ-8I 400 mil SOJ 8 ns Industrial GS74116AJ-10I 400 mil SOJ 10 ns Industrial GS74116AJ-12I 400 mil SOJ 12 ns Industrial GS74116AX-6 Fine Pitch BGA 6 ns Commercial GS74116AX-7 Fine Pitch BGA 7 ns Commercial Rev: 1.02 3/2002 13/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. Status (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X Ordering Information Part Number* Package Access Time Temp. Range GS74116AX-8 Fine Pitch BGA 8 ns Commercial GS74116AX-10 Fine Pitch BGA 10 ns Commercial GS74116AX-12 Fine Pitch BGA 12 ns Commercial GS74116AX-6I Fine Pitch BGA 6 ns Industrial GS74116AX-7I Fine Pitch BGA 7 ns Industrial GS74116AX-8I Fine Pitch BGA 8 ns Industrial GS74116AX-10I Fine Pitch BGA 10 ns Industrial GS74116AX-12I Fine Pitch BGA 12 ns Industrial Status * Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. For example: GS74116ATP-8T Rev: 1.02 3/2002 14/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. GS74116ATP/J/X 4Mb Asynchronous Datasheet Revision History Rev. Code: Old; New 74116A_r1 Types of Changes Format or Content Format/Content Page #/Revisions/Reason * Created new datasheet 74116A_r1; 74116A_r1_01 Content * Added 6 ns and 7 ns speed bins * Updated power numbers * Changed FPBGA package size from 7.2 x 11.65 mm to 6 x 10 mm * Changed package designator from "U" to "X" for FPBGA * Changed D3 on FPBGA pinout to A17 and E3 to NC 74116A_r1_01; 74116A_r1_02 Content * Updated Recommended Operating Conditions on page 4 * Updated Read Cycle and Write Cycle AC Characteristics tables Rev: 1.02 3/2002 15/15 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc.