LTC4257 IEEE 802.3af PD Power over Ethernet Interface Controller U FEATURES DESCRIPTIO Complete Power Interface Port for IEEE 802.3af(R) Powered Devices (PDs) Onboard 100V, 400mA Power MOSFET Precision Input Current Limit Onboard 25k Signature Resistor Programmable Classification Current (Class 0-4) Undervoltage Lockout Smart Thermal Protection Power Good Signal Available in 8-Pin SO and Low Profile (3mm x 3mm) DFN Packages U APPLICATIO S IP Phone Power Management Wireless Access Points Telecom Power Control The LTC(R)4257 provides complete signature and power interface functions for a device operating in an IEEE 802.3af Power over Ethernet (PoE) system. The LTC4257 simplifies Powered Device (PD) design by incorporating the 25k signature resistor, the classification current source, input current limit with thermal foldback, undervoltage lockout and power good signalling, all in a single 8-pin package. By incorporating a high voltage power MOSFET onboard, the LTC4257 provides the system designer with reduced cost while also saving board space. The LTC4257 can interface directly with a variety of Linear Technology DC/DC converter products to provide a cost effective power solution for IP phones, wireless access points and other PDs. Linear Technology also provides solutions for Power Sourcing Equipment (PSE) applications with quad network power controllers. The LTC4257 is available in the 8-pin SO and low profile (3mm x 3mm) DFN packages. , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. U TYPICAL APPLICATIO LTC4257 Charging 300F Load Capacitor Powered Device (PD) -48V FROM POWER SOURCING EQUIPMENT (PSE) ~ + DF01SA ~ - LTC4257 GND SMAJ58A RCLASS 0.1F VIN 50V/DIV 100k PWRGD RCLASS 5F MIN + SWITCHING POWER SUPPLY SHDN RTN VIN VOUT VOUT 20V/DIV VIN + 3.3V TO LOGIC 4257 TA01 IIN 200mA/DIV - PWRGD 50V/DIV 5ms/DIV 4225 TA02 4257fb 1 LTC4257 W W W AXI U U ABSOLUTE RATI GS (Notes 1, 2) VIN Voltage ............................................. 0.3V to - 100V VOUT, PWRGD Voltage ............. VIN + 100V to VIN - 0.3V RCLASS Voltage ............................ VIN + 7V to VIN - 0.3V PWRGD Current .................................................. 10mA RCLASS Current .................................................. 100mA Operating Ambient Temperature Range LTC4257C ............................................... 0C to 70C LTC4257I ............................................. -40C to 85C Storage Temperature Range S8 Package ....................................... - 65C to 150C DD Package ...................................... - 65C to 125C Lead Temperature (Soldering, 10 sec).................. 300C U U W PACKAGE/ORDER I FOR ATIO TOP VIEW TOP VIEW NC 1 RCLASS 2 8 7 GND NC 1 8 GND RCLASS 2 7 NC NC 3 6 PWRGD VIN 4 5 VOUT NC NC 3 6 PWRGD VIN 4 5 VOUT DD PACKAGE 8-LEAD (3mm x 3mm) PLASTIC DFN S8 PACKAGE 8-LEAD PLASTIC SO TJMAX = 150C, JA = 150C/W TJMAX = 125C, JA = 43C/W EXPOSED PAD TO BE SOLDERED TO ELECTRICALLY ISOLATED PCB HEATSINK ORDER PART NUMBER S8 PART MARKING ORDER PART NUMBER DD PART MARKING* LTC4257CS8 LTC4257IS8 4257 4257I LTC4257CDD LTC4257IDD LACT Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grades are identified by a label on the shipping container. ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL PARAMETER CONDITIONS MIN VIN Supply Voltage Maximum Operating Voltage Signature Range Classification Range UVLO Turn-On Voltage UVLO Turn-Off Voltage Voltage with Respect to GND Pin (Notes 4, 5, 6) IIN_ON IC Supply Current when ON VIN = - 48V, Pins 5, 6 Floating IIN_CLASS IC Supply Current During Classification VIN = - 17.5V, Pin 2 Floating, VOUT Tied to GND (Note 7) ICLASS Current Accuracy During Classification 10mA < ICLASS < 40mA, - 12.5V VIN - 21V, (Notes 8, 9) TYP MAX UNITS - 1.5 - 12.5 - 37.7 - 29.3 -39.2 -30.5 - 57 - 9.5 - 21 - 40.2 - 31.5 V V V V V 3 mA 0.35 0.50 0.65 mA 3.5 % 4257fb 2 LTC4257 ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL RSIGNATURE PARAMETER Signature Resistance CONDITIONS -1.5V VIN -9.5V, VOUT Tied to GND, IEEE 802.3af 2-Point Measurement (Notes 4, 5) VPG_OUT Power Good Output Low Voltage I = 1mA, VIN = - 48V, PWRGD Referenced to VIN Power Good Trip Point VIN = -48V, Voltage Between VIN and VOUT (Note 9) VOUT Falling VOUT Rising VPG_THRES_FALL VPG_THRES_RISE MIN 23.25 1.3 2.7 TYP MAX 26.00 UNITS k 0.5 V 1.5 3.0 1.7 3.3 V V 1 A 1.0 IPG_LEAK Power Good Leakage VIN = 0V, PWRGD FET Off, VPWRGD = 57V RON On-Resistance I = 300mA, VIN = - 48V, Measured from VIN to VOUT (Note 9) 1.6 2.0 150 A 400 mA IOUT_LEAK VOUT Leakage VIN = 0V, Power MOSFET Off, VOUT = 57V (Note 10) ILIMIT Input Current Limit VIN = - 48V, VOUT = -43V (Note 11) ILIMIT_WARM Overtemperature Input Current Limit (Note 11) 188 mA TOVERTEMP Overtemperature Trip Temperature (Note 11) 120 C TSHUTDOWN Thermal Shutdown Trip Temperature (Note 11) 140 C Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltages are with respect to GND pin. Note 3: The LTC4257 operates with a negative supply voltage in the range of -1.5V to -57V. To avoid confusion, voltages in this data sheet are always referred to in terms of absolute magnitude. Terms such as "maximum negative voltage" refer to the largest negative voltage and a "rising negative voltage" refers to a voltage that is becoming more negative. Note 4: The LTC4257 is designed to work with two polarity protection diodes between the PSE and PD. Parameter ranges specified in the Electrical Characteristics are with respect to LTC4257 pins and are designed to meet IEEE 802.3af specifications when these diode drops are included. See Applications Information. Note 5: Signature resistance is measured via the 2-point V/I method as defined by IEEE 802.3af. The LTC4257 signature resistance is offset from 25k to account for diode resistance. With two series diodes, the total PD resistance will be between 23.75k and 26.25k and meet IEEE 802.3af specifications. The minimum probe voltages measured at the LTC4257 pins are -1.5V and -2.5V. The maximum probe voltages are -8.5V and -9.5V. Note 6: The LTC4257 includes hysteresis in the UVLO voltages to preclude any start-up oscillation. Per IEEE 802.3af requirements, the LTC4257 will 300 350 power up from a voltage source with 20 series resistance on the first trial. Note 7: IIN_CLASS does not include classification current programmed at Pin 2. Total supply current in classification mode will be IIN_CLASS + ICLASS (see Note 8). Note 8: ICLASS is the measured current flowing through RCLASS. ICLASS accuracy is with respect to the ideal current defined as ICLASS = 1.237/RCLASS. The current accuracy specification does not include variations in RCLASS resistance. The total classification current for a PD also includes the IC quiescent current (IIN_CLASS). See Applications Information. Note 9: For the DD package, this parameter is assured by design and wafer level testing. Note 10: IOUT_LEAK includes current drawn at the VOUT pin by the power good status circuit. This current is compensated for in the 25k signature resistance and does not affect PD operation. Note 11: The LTC4257 includes smart thermal protection. In the event of an overtemperature condition, the LTC4257 will reduce the input current limit by 50% to reduce the power dissipation in the package. If the part continues heating and reaches the shutdown temperature, the current is reduced to zero until the part cools below the overtemperature limit. The LTC4257 is also protected against thermal damage from incorrect classification probing by the PSE. If the LTC4257 exceeds the overtemperature trip point, the classification load current is disabled. 4257fb 3 LTC4257 U W TYPICAL PERFOR A CE CHARACTERISTICS Input Current vs Input Voltage 25k Detection Range 0.5 Input Current vs Input Voltage Input Current vs Input Voltage 50 TA = 25C 12.0 TA = 25C CLASS 4 11.5 0.3 0.2 INPUT CURRENT (mA) 40 INPUT CURRENT (mA) INPUT CURRENT (mA) 0.4 CLASS 1 OPERATION CLASS 3 30 CLASS 2 20 CLASS 1 0.1 10 11.0 85C 10.5 -40C 10.0 9.5 CLASS 0 0 -2 -4 -6 INPUT VOLTAGE (V) 0 -10 -8 0 -20 -30 -40 INPUT VOLTAGE (V) -10 4357 G02 -50 -45 -55 INPUT VOLTAGE (V) -60 26 LTC4257 + 2 DIODES 25 24 LTC4257 ONLY IEEE LOWER LIMIT 23 22 V1: -1 V2: -2 -3 -4 -7 -5 -8 -6 INPUT VOLTAGE (V) 4257 G04 -1 60 0 20 40 TEMPERATURE (C) 80 Current Limit vs Input Voltage VOUT = VIN + 5V 365 CURRENT LIMIT (mA) 60 30 1 -20 4257 G06 375 90 VOUT CURRENT (A) VPG_OUT (V) 0 -2 -40 -9 -10 VIN = 0V TA = 25C TA = 25C 2 APPLICABLE TO TURN-ON AND TURN-0FF THRESHOLDS 1 VOUT Leakage Current 120 3 -22 4257 G05 Power Good Output Low Voltage vs Current 4 2 RESISTANCE = V = V2 - V1 I I2 - I1 27 DIODES: S1B TA = 25C IEEE UPPER LIMIT SIGNATURE RESISTANCE (k) INPUT CURRENT (mA) 1 -20 -18 -16 INPUT VOLTAGE (V) Normalized UVLO Threshold vs Temperature 28 2 -14 4257 G03 Signature Resistance vs Input Voltage EXCLUDES ANY LOAD CURRENT TA = 25C 0 -40 9.0 -12 -60 4257 G01 Input Current vs Input Voltage 3 -50 NORMALIZED UVLO THRESHOLD (%) 0 85C 355 25C 345 -40C 335 0 0 0 2 6 4 CURRENT (mA) 8 10 4257 G07 0 20 40 VOUT PIN VOLTAGE (V) 60 42571 G09 325 -40 -50 -45 -55 INPUT VOLTAGE (V) -60 4257 G09 4257fb 4 LTC4257 U U U PI FU CTIO S NC (Pin 1): No Connect. RCLASS (Pin 2): External Class Select Input. Used to set the current the LTC4257 maintains during classification. Connect a resistor between RCLASS and VIN (see Table 2). NC (Pin 3): No Connect. PWRGD (Pin 6): Power Good Output, Open-Drain. Signals that the LTC4257 MOSFET is fully on. Low impedance indicates power is good. PWRGD is high impedance during detection, classification and in the event of a thermal overload. PWRGD is referenced to VIN. NC (Pin 7): No Connect VIN (Pin 4): Power Input. Tie to system - 48V through the input diode bridge. GND (Pin 8): Ground. Tie to system ground and to power return through the input diode bridge. VOUT (Pin 5): Power Output. Supplies - 48V to the PD load through an internal power MOSFET that limits input current. VOUT is high impedance until the input voltage rises above the turn-on UVLO threshold. Above the UVLO threshold the output is current limited to 350mA. W BLOCK DIAGRA CLASSIFICATION CURRENT SOURCE NC 1 1.237V + - EN 25k SIGNATURE RESISTOR RCLASS 2 NC 3 POWER GOOD CONTROL CIRCUITS 350mA + 8 GND 7 NC 6 PWRGD INPUT EN CURRENT LIMIT - 0.3 VIN 4 5 VOUT BOLD LINE INDICATES HIGH CURRENT PATH 4257 BD 4257fb 5 LTC4257 U W U U APPLICATIO S I FOR ATIO The LTC4257 is intended for use as the front end of a Powered Device (PD) designed to IEEE 802.3af draft standard. The LTC4257 includes a trimmed 25k signature resistor, classification current source, and an inrush current limit circuit. With these functions integrated into the LTC4257, the signature and power interface for a PD that meets all the requirements of IEEE 802.3af can be built with a minimum of external components. DETECTION V1 VIN (V) -10 -20 UVLO TURN-OFF UVLO TURN-ON -30 -40 -50 TIME = RLOAD C1 -10 VOUT (V) Using an LTC4257 for the power and signature interface functions of a PD provides several advantages. The LTC4257 current limit circuit includes an onboard, 100V, 400mA power MOSFET with low leakage. This onboard low leakage MOSFET avoids the possibility of corrupting the 25k signature resistor while also saving board space and cost. In addition, the IEEE 802.3af inrush current limit requirement causes large transient power dissipation in the PD; the LTC4257 manages this turn-on sequence through the use of smart thermal protection circuitry. The LTC4257 is designed to allow multiple turn-on sequences without overheating the miniature 8-lead package. In the event of excessive power cycling, the LTC4257 provides thermally activated current-limit reduction to keep the onboard power MOSFET within its safe operating area. UVLO OFF -20 -30 UVLO ON UVLO OFF dV = ILIMIT C1 dt -40 -50 TIME PWRGD (V) -10 POWER BAD -20 POWER GOOD POWER BAD -30 -40 PWRGD TRACKS VIN -50 CURRENT LIMIT, ILIMIT PD CURRENT ILIMIT Operation The LTC4257 has several modes of operation depending on the applied input voltage as shown in Figure 1 and summarized in Table 1. These various modes satisfy the requirements defined in the IEEE 802.3af specification. The input voltage is applied to the VIN pin and is with reference to the GND pin. This input voltage is always negative. To avoid confusion, voltages in this data sheet are always referred to in terms of absolute magnitude. Terms such as maximum negative voltage refer to the largest negative voltage and a rising negative voltage refers to a voltage that is becoming more negative. References to electrical parameters in this applications section use the nominal value. Refer to the Electrical Characteristics section for the range of values a particular parameter will have. TIME DETECTION V2 CLASSIFICATION LOAD CURRENT, ILOAD ICLASS CLASSIFICATION ICLASS DETECTION I2 DETECTION I1 I1 = V1 - 2 DIODE DROPS 25k V2 - 2 DIODE DROPS 25k ICLASS DEPENDENT ON RCLASS SELECTION I2 = ILIMIT = 350mA (NOMINAL) ILOAD = VIN RLOAD GND LTC4257 IIN PSE 2 RCLASS GND VIN R CLASS PWRGD 4 VIN VOUT 8 6 R9 RLOAD C1 VOUT 5 4257 F01 Figure 1. Output Voltage, PWRGD and PD Current as a Function of Input Voltage 4257fb 6 LTC4257 U W U U APPLICATIO S I FOR ATIO Detection Table 1. LTC4257 Operational Mode as a Function of Input Voltage INPUT VOLTAGE (VIN with RESPECT to GND) LTC4257 MODE OF OPERATION 0V to - 1.4V Inactive - 1.5V to - 10V 25k Signature Resistor Detection - 11V to - 12.4V Classification Load Current Ramps up from 0% to 100% - 12.5V to UVLO* Classification Load Current Active UVLO* to -57V Power Applied to PD Load During detection, the PSE will apply a voltage in the range of -2.8V to -10V on the cable and look for a 25k signature resistor. This identifies the device at the end of the cable as a PD. With the terminal voltage in this range, the LTC4257 connects an internal 25k resistor between GND and the VIN pins. This precision, temperature compensated resistor presents the proper characteristics to alert the Power Sourcing Equipment (PSE) at the other end of the cable that a PD is present and desires power to be applied. *UVLO includes hysteresis. Rising input threshold - 39.2V Falling input threshold - 30.5V The power applied to a PD is allowed to use either of two polarities and the PD must be able to accept this power so it is common to install a diode bridge on the input. The LTC4257 is designed to compensate for the voltage and resistance effects of these two series diodes. The signature range extends below the IEEE range to accommodate the voltage drop of the diodes. The IEEE specification requires the PSE to use a V/I measurement technique to keep the DC offset of these diodes from affecting the signature resistance measurement. However, the diode resistance appears in series with the signature resistor and must be included in the overall signature resistance of the PD. The LTC4257 compensates for the two series diodes in the signature path by offsetting the resistance so that a PD built using the LTC4257 will meet the IEEE requirements. Series Diodes The IEEE 802.3af defined operating modes for a PD reference the input voltage at the RJ45 connector on the PD. However, PD circuitry must include diode bridges between the RJ45 connector and the LTC4257 (Figure 2). The LTC4257 takes this into account by compensating for these diode drops in the threshold points for each range of operation. Since the voltage ranges specified in the LTC4257 electrical specifications are with respect to the IC pins for both the signature and classification ranges, the LTC4257 lower end extends two diode drops below the IEEE 802.3af specification. A similar adjustment is made for the UVLO voltages. RJ45 1 2 3 POWERED DEVICE (PD) INTERFACE AS DEFINED BY IEEE 802.3af 6 TX + T1 TX - RX + BR1 TO PHY RX - GND 4 SPARE + LTC4257 BR2 5 D3 4 7 8 8 VIN SPARE - 4257 F02 Figure 2. PD Front End Using Diode Bridges on Main and Spare Inputs 4257fb 7 LTC4257 U W U U APPLICATIO S I FOR ATIO Classification Once the PSE has detected a PD, the PSE may optionally classify the PD. Classification provides a method for more efficient allocation of power by allowing the PSE to identify lower-power PDs and allocate less power for these devices. IEEE 802.3af defines five classes (Table 2) with varying power levels. The designer selects the appropriate classification based on the power consumption of the PD. For each class, there is an associated load current that the PD asserts onto the line during classification probing. The PSE measures the PD load current to determine the proper classification and PD power requirements. Table 2. Summary of IEEE 802.3af Power Classifications and LTC4257 RCLASS Resistor Selection MAXIMUM NOMINAL POWER LEVELS CLASSIFICATION AT INPUT OF PD LOAD CURRENT CLASS USAGE (W) (mA) 0 Default 0.44 to 12.95 <5 1 Optional 0.44 to 3.84 10.5 2 Optional 3.84 to 6.49 18.5 3 Optional 6.49 to 12.95 28 4 Reserved Reserved* 40 *Class 4 is currently reserved and should not be used. LTC4257 RCLASS RESISTOR (, 1%) Open 124 68.1 45.3 30.9 Early revisions of the IEEE 802.3af draft specification defined two methods that a PSE could use in order to perform PD classification. These methods are known as Measured Current and Measured Voltage. The IEEE has since removed the Measured Voltage method from the specification. The LTC4257 is compatible with the IEEE 802.3af standard and also works with the obsolete Measured Voltage method. In the Measured Current method (Figure 3), the PSE presents a fixed voltage between -15.5V and -20V to the PD. With the input voltage in this range, the LTC4257 asserts a load current from the GND pin through the RCLASS resistor. The magnitude of the load current is set with the selection of the RCLASS resistor. The resistor value associated with each class is shown in Table 2. In the Measured Voltage method (Figure 4), the PSE drives a current into the PD and monitors the voltage across the PD terminals. The PSE current steps between classification load current values in order to classify the PD under test. For PSE probe currents below the PD load current, the LTC4257 will keep the PD terminal voltage below the classification voltage range. For PSE probe currents above the PD load current, the LTC4257 will force the PD terminal voltage above the classification voltage range. During classification, a moderate amount of power is dissipated in the LTC4257. IEEE 802.3af limits the classification time to 75ms. The LTC4257 is designed to handle the power dissipation for this time period. If the PSE CURRENT PATH CURRENT PATH PSE PROBING VOLTAGE SOURCE -15.5V TO -20.5V PSE PROBING CURRENT SOURCE LTC4257 2 RCLASS GND 8 RCLASS 4 VIN 4257 F03 V PD LTC4257 MONITOR CONSTANT LOAD CURRENT INTERNAL TO LTC4257 2 RCLASS RCLASS 4 VIN PSE PSE CURRENT MONITOR PSE PSE V VOLTAGE GND 8 CONSTANT LOAD CURRENT INTERNAL TO LTC4257 PD IF PSE PROBING CURRENT < LTC4257 LOAD CURRENT, PD TERMINAL VOLTAGE IS < 15V IF PSE PROBING CURRENT > LTC4257 LOAD CURRENT, PD TERMINAL VOLTAGE IS > 20V 4257 F04 Figure 3. IEEE 802.3af Measured-Current Method of Classification Probing Figure 4. IEEE 802.af Measured-Voltage Method of Classification Probing 4257fb 8 LTC4257 U W U U APPLICATIO S I FOR ATIO probing exceeds 75ms, the LTC4257 may overheat. In this situation, the thermal protection circuit will engage and disable the classification current source in order to protect the part. The LTC4257 stays in classification mode until the input voltage rises above the UVLO turn-on voltage. Undervoltage Lockout IEEE 802.3af dictates a maximum turn-on voltage of 42V and a minimum turn-off voltage of 30V for the PD. In addition, the PD must maintain large on-off hysteresis to prevent resistive losses in the wiring between the PSE and the PD from causing start-up oscillation. The LTC4257 incorporates an undervoltage lockout (UVLO) circuit that monitors line voltage to determine when to apply power to the PD load (Figure 5). Before power is applied to the load, the VOUT pin is high impedance and at ground potential since there is no charge on capacitor C1. When the input voltage rises above the UVLO turn-on threshold, the LTC4257 removes the classification load current and turns on the internal power MOSFET. C1 charges up under LTC4257 current limit control and the VOUT pin transitions from 0V to VIN. This sequence is shown in Figure 1. The LTC4257 includes a hysteretic UVLO circuit that keeps power applied to the load until the input voltage falls below the UVLO turn-off threshold. Once the input voltage drops below -30V, the internal power MOSFET is turned off and the classification load current is re-enabled. C1 will discharge through the PD circuitry and the V OUT pin will go to a high impedance state. Input Current Limit IEEE 802.3af specifies a maximum inrush current and also specifies a minimum load capacitor between the GND and VOUT pins. To control turn-on surge current in the system, the LTC4257 integrates a current limit circuit with the onboard power MOSFET and sense resistor to provide a complete inrush control circuit without additional external components. The LTC4257 limits input current to less than the 400mA maximum specified by 802.3af, allowing the load capacitor to ramp up to the line voltage in a controlled manner. During this ramp up, a large amount of power is dissipated in the power MOSFET. The LTC4257 LTC4257 TO PSE GND 8 C1 5F MIN + PD LOAD UNDERVOLTAGE LOCKOUT CIRCUIT VOUT 5 4 VIN INPUT LTC4257 VOLTAGE POWER MOSFET 0V TO UVLO* OFF >UVLO* ON *UVLO INCLUDES HYSTERESIS RISING INPUT THRESHOLD -39.2V FALLING INPUT THRESHOLD -30.5V 4257 F05 CURRENT-LIMITED TURN ON Figure 5. LTC4257 Undervoltage Lockout 4257fb 9 LTC4257 U W U U APPLICATIO S I FOR ATIO is designed to accept this thermal load and is thermally protected to avoid damage to the onboard power MOSFET. Note that the PD designer must ensure that the PD steadystate power consumption falls within the limits shown in Table 2. design of a PD, it is necessary to determine if a step in the input voltage will cause the PWRGD signal to go inactive and how to respond to this event. In some designs, the charge on C1 is sufficient to power the PD through this event. In this case, it may be desirable to filter the PWRGD signal so that intermittent power bad conditions are ignored. Figure 10 demonstrates methods to insert a lowpass filter on the power good interface. Power Good The LTC4257 includes a power good circuit (Figure 6) that is used to indicate to the PD circuitry that load capacitor C1 is fully charged and that the PD can start DC/DC converter operation. The power good circuit monitors the voltage across the internal power MOSFET and PWRGD is asserted when the voltage drops below 1.5V. The power good circuit includes a large amount of hysteresis to allow the LTC4257 to operate near the current limit point without inadvertently disabling PWRGD. The MOSFET voltage must increase to 3V before PWRGD is disabled. For PD designs that use a large load capacitor and also consume a lot of power, it is important to delay activation of the PD circuitry with the PWRGD signal. If the PD circuitry is not disabled during the current-limited turn-on sequence, the PD circuitry will rob current intended for charging up the load capacitor and create a slow rising input, possibly causing the LTC4257 to go into thermal shutdown. The PWRGD pin connects to an internal open-drain, 100V transistor capable of sinking 1mA. Low impedance indicates power is good. PWRGD is high impedance during signature and classification probing and in the event of a thermal overload. If a sudden increase in voltage appears on the input line, this voltage step will be transferred through capacitor C1 and appear across the power MOSFET. The response of the LTC4257 will depend on the magnitude of the voltage step, the rise time of the step, the value of capacitor C1 and the DC load. For fast rising inputs, the LTC4257 will attempt to quickly charge capacitor C1 using an internal secondary current limit circuit. In this scenario, the PSE current limit should provide the overall limit for the circuit. For slower rising inputs, the 350mA current limit in the LTC4257 will set the charge rate of capacitor C1. In either case, the PWRGD signal may go inactive briefly while the capacitor is charged up to the new line voltage. In the During turn-off, PWRGD is deactivated when the input voltage drops below 30V. In addition, PWRGD may go active briefly at turn-on for fast rising input waveforms. PWRGD is referenced to the VIN pin and when active will be near the VIN potential. The PD DC/DC converter will typically be referenced to VOUT and care must be taken to ensure that the difference in potential of the PWRGD signal does not cause any detrimental effects. Use of diode clamp D6, as shown in Figure 10, will alleviate any problems. LTC4257 PWRGD 6 R9 100k SHDN PD LOAD THERMAL SHUTDOWN UVLO - TO PSE + C1 5F MIN + - 1.125V 300k 4 VIN + 300k VOUT 5 4257 F06 Figure 6. LTC4257 Power Good 4257fb 10 LTC4257 U W U U APPLICATIO S I FOR ATIO Thermal Protection The LTC4257 includes smart thermal protection in order to provide full device functionality in a miniature package while maintaining safe operating temperatures. Several factors create the possibility for tremendous power dissipation within the LTC4257. IEEE 802.3af mandates that inrush current be limited to less than 400mA while standard telecom power can be as high as 57V. At turn on, before the load capacitor has charged up, the instantaneous power dissipated by the LTC4257 can be over 20W. As the load capacitor charges up, the power dissipation in the LTC4257 will decrease until it reaches a steady-state value dependent on the DC load current. The size of the load capacitor determines how fast the power dissipation in the LTC4257 subsides. At room temperature, the LTC4257 can handle load capacitors as large as 800F without going into thermal shutdown. With a large load capacitor like this, the LTC4257 die temperature will increase by about 50C during a single turn-on sequence. If for some reason power were removed from the part and then quickly reapplied so that the LTC4257 had to charge up the load capacitor again, the temperature rise would be excessive if safety precautions were not implemented. The LTC4257 protects itself from thermal damage by monitoring the die temperature. If the die temperature exceeds the overtemperature trip point, the part switches to a half-power mode where the current limit is set to 50% of its normal level. This reduces power dissipation and helps prevent further heating. If the part continues to heat up and reaches the shutdown temperature, the current is reduced to zero and very little power is dissipated in the part until it cools below the overtemperature set point. The LTC4257 current limit will continue switching between 0%, 50% and 100% current levels (Figure 7) until the load capacitor is fully charged. If the PD is designed to operate at a high ambient temperature and with the maximum allowable supply (57V), there will be a limit to the size load capacitor that can be charged up before the LTC4257 reaches the overtemperature trip point. Hitting the overtemperature trip point intermittently does not harm the LTC4257, but it will delay completion of capacitor charging. Capacitors up to 200F can be charged without a problem. During classification, excessive heating of the LTC4257 can occur if the PSE violates the 75ms probing time limit. To protect the LTC4257, the thermal protection circuitry will disable classification current if the die temperature exceeds the overtemperature trip point. When the die cools down below the trip point, classification current is re-enabled. Once the LTC4257 has charged up to the load capacitor and the PD is powered and running, there will be some residual heating due to the DC load current of the PD flowing through the internal MOSFET. In some applications, the LTC4257 power dissipation may be significant and if dissipated in the S8 package, excessive package heating could occur. This problem can be solved with the use of the DD package which has superior thermal performance. The DD package includes an exposed pad that should be soldered to an isolated heatsink on the printed circuit board. T > 120C UVLO TURN ON 100% CURRENT 50% CURRENT T < 120C T < 120C T > 140C 0% CURRENT 4257 F07 Figure 7. Smart Thermal Protection State Diagram 4257fb 11 LTC4257 U W U U APPLICATIO S I FOR ATIO EXTERNAL INTERFACE AND COMPONENT SELECTION Diode Bridges Transformer IEEE 802.3af allows power wiring in either of two configurations on the TX/RX wires, plus power can be applied to the PD via the spare wire pair in the RJ45 connector. The PD is required to accept power in either polarity on both the main and spare inputs, therefore it is common to install diode bridges on both inputs in order to accommodate the different wiring configurations. Figure 8 demonstrates an implementation of these diode bridges. The specification also mandates that the leakage back through the unused bridge be less than 28A when the PD is powered with 57V. Nodes on an Ethernet network commonly interface to the outside world via an isolation transformer (Figure 8). For powered devices, the isolation transformer must include a center tap on the media (cable) side. Proper termination is required around the transformer to provide correct impedance matching and to avoid radiated and conducted emissions. Transformer vendors such as Pulse, Bel Fuse, Tyco and others (Table 3) can provide assistance with selection of an appropriate isolation transformer and proper termination methods. These vendors have transformers specifically designed for use in PD applications. Table 3. Power over Ethernet Transformer Vendors VENDOR CONTACT INFORMATION Pulse Engineering 12220 World Trade Drive San Diego, CA 92128 Tel: 858-674-8100 FAX: 858-674-8262 http://www.pulseeng.com/ Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel: 201-432-0463 FAX: 201-432-9542 http://www.belfuse.com/ Tyco Electronics 308 Constitution Drive Menlo Park, CA 94025-1164 Tel: 800-227-7040 FAX: 650-361-2508 http://www.circuitprotection.com/ RJ45 1 2 3 6 4 TX + 2 TX - 14 3 RX + 11 6 10 7 8 The input diode bridge of a PD can consume 4% of the avialable power in some applications. It may be desirable to use Scottky diodes in order to reduce this power loss. 9 8 BR1 DF01SA TO PHY PULSE H2019 SPARE + 5 7 The LTC4257 has several different modes of operation based on the voltage present between the VIN and GND pins. The forward voltage drop of the input diodes in a PD design subtracts from the input voltage and will affect the transition point between modes. When using the LTC4257, it is necessary to pay close attention to this forward voltage drop. Selection of oversized diodes will help keep the PD thresholds from exceeding IEEE specifications. 16 T1 1 15 RX - The IEEE standard includes an AC impedance requirement in order to implement the AC disconnect function. Capacitor C14 in Figure 8 is used to meet this AC impedance requirement. A 0.1F capacitor is recommended for this application. SPARE - GND BR2 DF01SA C14 0.1F 100V 8 C1 LTC4257 D3 SMAJ58A TVS 4 VIN VOUT 5 4257 F08 VOUT Figure 8. PD Front End with Isolation Transformer, Diode Bridges and Capacitor 4257fb 12 LTC4257 U W U U APPLICATIO S I FOR ATIO However, if the standard diode bridge is replaced with a Schottky bridge, the transition points between modes will be affected. The application circuit (Figure 11) shows a technique for using Schottky diodes while maintaining proper threshold points to meet IEEE 802.3af compliance. Auxiliary Power Source In some applications, it may be desirable to power the PD from an auxiliary power source such as a wall transformer. The auxiliary power can be injected into the PD at several locations and various trade-offs exist. Power can be injected at the 3.3V or 5V output of the isolated power supply with the use of a diode ORing circuit. This method accesses the internal circuits of the PD after the isolation barrier and therefore meets the 802.3af isolation safety requirements for the wall transformer jack on the PD. Power can also be injected into the PD interface portion of the LT4257. In this case, it is necessary to ensure the user cannot access the terminals of the wall transformer jack on the PD since this would compromise the 802.3af isolation safety requirements. Figure 9 demonstrates three methods of diode ORing external power into a PD. Option 1 inserts power before the LTC4257 while options 2 and 3 insert power after the LTC4257. If power is inserted before the LTC4257 (option 1), it is necessary for the wall transformer to exceed the LTC4257 UVLO turn-on requirement and limit the maximum voltage to 57V. This option provides input current limiting for the transformer, provides valid power good signaling and simplifies power priority issues. As long as the wall transformer applies power to the PD before the PSE, it will take priority and the PSE will not power up the PD because the wall power will corrupt the 25k signature. If the PSE is already powering the PD, the wall transformer power will be in parallel with the PSE. In this case, priority will be given to the higher supply voltage. If the wall transformer voltage is higher, the PSE should remove line voltage since no current will be drawn from the PSE. On the other hand, if the wall transformer voltage is lower, the PSE will continue to supply power to the PD and the wall transformer power will not be used. Proper operation should occur in either scenario. Auxiliary power can be applied after the LTC4257 as shown in option 2. In this configuration, the wall transformer does not need to exceed the LTC4257 turn-on UVLO requirement; however, it is necessary to include diode D9 to prevent the transformer from applying power to the LTC4257. The transformer voltage requirements will be governed by the needs of the PD switcher and may exceed 57V. However, power priority issues require more intervention. If the wall transformer voltage is below the PSE voltage, then priority will be given to the PSE power. The PD will draw power from the PSE while the transformer will sit unused. This configuration is not a problem in a PoE system. On the other hand, if the wall transformer voltage is higher than the PSE voltage, the PD will draw power from the transformer. In this situation, it is necessary to address the issue of power cycling that may occur if a PSE is present. The PSE will detect the PD and apply power. If the PD is being powered by the wall transformer, then the PD will not meet the minimum load requirement and the PSE will subsequently remove power. The PSE will again detect the PD and power cycling will start. With a transformer voltage above the PSE voltage, it is necessary to install a minimum load on the output of the LTC4257 to prevent power cycling. Refer to the LTC4257-1 data sheet for an alternative implementation of option 2 which uses the Signature Disable feature. The third option also applies power after the LTC4257, while omitting diode D9. With the diode omitted, the transformer voltage is applied to the LTC4257 in addition to the load. For this reason, it is necessary to ensure that the transformer maintain the voltage between 44V and 57V to keep the LTC4257 in its normal operating range. The third option has the advantage of automatically disabling the 25k signature when the external voltage exceeds the PSE voltage. 4257fb 13 LTC4257 U W U U APPLICATIO S I FOR ATIO OPTION 1: AUXILIARY POWER INSERTED BEFORE LTC4257 RJ45 1 2 3 6 TX + T1 ~ TX - RX + + BR1 DF01SA TO PHY ~ RX - D3 SMAJ58A TVS C14 0.1F 100V - GND SPARE + 4 ~ 5 PD LOAD C1 8 + LTC4257 BR2 DF01SA 7 SPARE - 8 ~ 4 - + VIN 5 VOUT D8 S1B ISOLATED WALL 44V TO 57V TRANSFORMER - OPTION 2: AUXILIARY POWER INSERTED AFTER LTC4257 RJ45 1 2 3 6 TX + TX T1 ~ - RX + D3 SMAJ58A TVS BR1 DF01SA TO PHY ~ RX - + - C1 8 GND SPARE + 4 ~ 5 7 + ~ ISOLATED WALL TRANSFORMER - PD LOAD LTC4257 BR2 DF01SA SPARE - 8 MINIMUM LOAD C14 0.1F 100V 4 VIN 5 VOUT + D9 S1B D10 S1B - OPTION 3: AUXILIARY POWER APPLIED TO LTC4257 AND PD LOAD RJ45 1 2 3 6 TX + TX T1 ~ - RX + D3 SMAJ58A TVS BR1 DF01SA TO PHY ~ RX - + C14 0.1F 100V - C1 GND 4 SPARE + ~ 5 7 8 + 8 PD LOAD LTC4257 BR2 DF01SA SPARE - ~ ISOLATED WALL TRANSFORMER + 44V TO 57V - 4 VIN VOUT 5 D10 S1B - 42571 F09 Figure 9. Auxiliary Power Source for PD 4257fb 14 LTC4257 U W U U APPLICATIO S I FOR ATIO Classification Resistor Selection (RCLASS) IEEE 802.3af allows classifying PDs into four distinct classes with class 4 being reserved for future use (Table 2). An external resistor connected from RCLASS to VIN (Figure 3) sets the value of the classification current. The designer should determine which power category the PD falls into and then select the appropriate value of RCLASS from Table 2. If a unique classification current is required, the value of RCLASS can be calculated as: RCLASS = 1.237V/(IDESIRED - IIN_CLASS) where IIN_CLASS is the LTC4257 IC supply current during classification and is given in the electrical specifications. The RCLASS resistor must be 1% or better to avoid degrading the overall accuracy of the classification circuit. Resistor power dissipation will be 50mW maximum and is transient so heating is typically not a concern. In order to maintain loop stability, the layout should minimize capacitance at the RCLASS node. The classification circuit can be disabled by floating the RCLASS pin. The RCLASS pin should not be shorted to VIN as this would force the LTC4257 classification circuit to attempt to source very large currents. In this case, the LTC4257 will quickly go into thermal shutdown. Power Good Interface The PWRGD signal is controlled by a high voltage, opendrain transistor. Examples of active-high and active-low interface circuits for controlling the PD load are shown in Figure 10. In some applications it is desirable to ignore intermittent power bad conditions. This can be accomplished by including capacitor C15 in Figure 10 to form a lowpass filter. With the components shown, power bad conditions less than about 200s will be ignored. Conversely, in other applications it may be desirable to delay assertion of PWRGD to the PD load. The PWRGD signal can be delayed with the addition of capacitor C17 in Figure 10. ACTIVE-LOW ENABLE, 5.1V SWING GND 8 R9 100k LTC4257 TO PSE PWRGD -48V 4 VIN PD LOAD R18 10k 6 + VOUT 5 C1 5F 100V SHDN C15* 0.047F 10V D6 5.1V MMBZ5231B *C15 OPTIONAL TO FILTER PWRGD. SEE APPLICATIONS INFORMATION ACTIVE-HIGH ENABLE FOR RUN PIN WITH INTERNAL PULLUP GND TO PSE 8 LTC4257 PWRGD -48V 4 VIN Q1 FMMT2222 R18 10k 6 + VOUT 5 INTERNAL PULLUP R9 100k C1 5F 100V D6 MMBD4148 C15* 0.047F 10V PD LOAD RUN C17* 4257 F10 *C15 AND C17 OPTIONAL TO FILTER PWRGD. SEE APPLICATIONS INFORMATION Figure 10. Power Good Interface Examples 4257fb 15 LTC4257 U W U U APPLICATIO S I FOR ATIO Load Capacitor IEEE 802.3af requires that the PD maintain a minimum load capacitance of 5F. It is permissible to have a much larger load capacitor and the LTC4257 can charge very large load capacitors before thermal issues become a problem. However, the load capacitor must not be too large or the PD design may violate two IEEE 802.3af requirements. The LTC4257 goes into current limit at turn-on and charges the load capacitor with between 300mA and 400mA. The IEEE specification allows this level of inrush current for up to 50ms. Therefore, it is necessary that the PD complete charging of the capacitor within the 50ms time limit. With a maximum input voltage of -57V, these conditions limit the size of the load capacitor to 250F. Very small output capacitors (10F) will charge very quickly in current limit. The rapidly changing voltage at the output may reduce the current limit temporarily, causing the capacitor to charge at a somewhat reduced rate. Conversely, charging very large capacitors may cause the current limit to increase slightly. In either case, once the output voltage reaches its final value, the input current limit will be restored to its nominal value. If the load capacitor is too large there can be an additional problem with inadvertent power shutdown by the PSE. Consider the following scenario. If the PSE is running at - 57V (maximum allowed) and the PD has been detected and powered up, the load capacitor will be charged to nearly - 57V. If for some reason the PSE voltage suddenly is reduced to - 44V (minimum allowed), the input diodes will reverse bias and PD power will be supplied solely by the load capacitor. Depending on the size of the load capacitor and the DC load of the PD, the PD will not draw any power from the PSE for a period of time. If this period of time exceeds the IEEE 802.3af 300ms disconnect delay, the PSE may remove power from the PD. For this reason, it is necessary to evaluate the load capacitance and load current to ensure that inadvertent shutdown cannot occur. Maintain Power Signature In an IEEE 802.3af system, the PSE uses the maintain power signature (MPS) to determine if a PD continues to require power. The MPS requires the PD to periodically draw at least 10mA and also have an AC impedance less than 26.25k in parallel with 0.05F. The PD application circuits shown in this data sheet meet the requirements necessary to maintain power. If either the DC current is less than 10mA or the AC impedance is above 26.25k, the PSE might disconnect power. The DC current must be less than 5mA and the AC impedance must be above 2M to guarantee power will be removed. 4257fb 16 LTC4257 U W U U APPLICATIO S I FOR ATIO Layout The LTC4257 is relativity immune to layout problems. Excessive parasitic capacitance on the RCLASS pin should be avoided. If using the DD package, include an electrically isolated heat sink to which the exposed pad on the bottom of the package can be soldered. For optimal thermal performance, make the heat sink as large as possible. Voltages in a PD can be as large as - 57V, so high voltage layout techniques should be employed. The load capacitor connected between Pins 5 and 8 of the LTC4257 can store significant energy when fully charged. The design of a PD must ensure that this energy is not inadvertently dissipated in the LTC4257. The polarityprotection diode(s) prevent an accidental short on the cable from causing damage. However, if the VIN pin is shorted to the GND pin inside the PD while the load capacitor is charged, current will flow through the parasitic body diode of the internal MOSFET and may cause permanent damage to the LTC4257. Input Surge Suppression The LTC4257 is specified to operate with an absolute maximum voltage of - 100V and is designed to tolerate brief overvoltage events. However, the pins that interface to the outside world (primarily VIN and GND) can routinely see peak voltages in excess of 10kV. To protect the LTC4257, it is highly recommended that a transient voltage suppressor be installed between the bridge and the LTC4257 (D3 in Figure 2). 4257fb 17 IN FROM PSE RJ45 8 7 5 4 6 3 2 1 J2 SPARE- SPARE + 9 10 11 RX + RX - 14 15 16 TX - TX + 4 T1 R2 75 C3 0.01F 200V 8 7 6 3 2 1 RXOUT - RXOUT + TXOUT - TXOUT + OUT TO PHY C2 1000pF 2kV R1 75 C7 0.01F 200V R30 75 C24 0.01F 200V D15 B1100 D16 B1100 D14 B1100 D12 B1100 D11 B1100 RCLASS 1% 3 VOUT PWRGD NC GND D13 MMSD4148 LTC4257CDD VIN NC RCLASS NC D6 SMAJ58A C11 0.1F 100V NOTES: UNLESS OTHERWISE SPECIFIED 1. ALL RESISTORS ARE 5% 2. ALL CAPACITORS ARE 25V 3. SELECT RCLASS FOR CLASS 1-4 OPERATION. REFER TO DATA SHEET APPLICATIONS INFORMATION SECTION 4. CONNECT TO CHASSIS GROUND C4 TO C6: TDK C4532X5R0J107M C2, C23: AVX 1808GC102MAT D1, D7: MM3Z12VT1 D3: MMBD1505 D9 TO D12, D14 TO D16: DIODES INC., B1100 L1: COILCRAFT D01608C-472 T1: PULSE H2019 T2: PULSE PB2134 T3: PULSE PA0184 D17 B1100 R31 75 C25 0.01F 200V D10 B1100 D9 B1100 + D7 12V R17 10k R14 100k C1A 10F 100V R13 30.1k 1% D3A R23 3.65k 1% FB tON D1 12V C12 0.1F 50V C10 4.7F 35V R5 47K VCC UVLO R25 62k R26 10k R27 62k C13 470pF R11 10k GATE C19 47pF C20 0.47F Q2 MMBT3904 VC ISENSE Q5 MMBT3904 C21 0.1F C22 680pF 0603 Q4 MMBT2907ALT1 SFST RCMPC R9 100 C9 R8 100pF 47 R6 47 D2 BAT54 OSCAP SGND PGND LT1737CGN R10 62k D4 BAS21LT1 Q1 MMBTA06 MINENAB ROCMP ENDLY R7 33 1/4W D3B 3VOUT R24 100k C1C 0.82F 100V Q9 2N7002 C1B 0.82F 100V L1 4.7H R28 10k C17 3300pF Q3 Si4490DY R15 1* 0.22 1/2W T3 1% 8 C16 0.1F 50V R16 330 SEPARATING LINE FOR GROUND PLANE 3 1* 4* 5 Q6 Si7892DP R12 47 D5 B0540W VOUT- VOUT+ C4 TO C6 100F 6.3V 3.3V @ 2.8A R18 100 4257 TA04 4 R4 10k C14 1F Q7 Q8 FMMT718 MMBT3904 D8 BAT54 C23 1000pF 2kV 4 5 C18 1nF 10 9 11 8 T2 * * 18 * Figure 11: PD Power Interface with 3.3V, 2.8A High Efficiency Isolated Power Supply LTC4257 TYPICAL APPLICATIO 4257fb U LTC4257 U PACKAGE DESCRIPTIO S8 Package 8-Lead Plastic Small Outline (Narrow .150 Inch) (Reference LTC DWG # 05-08-1610) .189 - .197 (4.801 - 5.004) NOTE 3 .045 .005 .050 BSC .245 MIN 8 .160 .005 7 6 5 .053 - .069 (1.346 - 1.752) .150 - .157 (3.810 - 3.988) NOTE 3 .228 - .244 (5.791 - 6.197) .030 .005 TYP 1 3 2 NOTE: 1. DIMENSIONS IN INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE .050 (1.270) BSC .014 - .019 (0.355 - 0.483) TYP .010 - .020 x 45 (0.254 - 0.508) 4 RECOMMENDED SOLDER PAD LAYOUT .004 - .010 (0.101 - 0.254) .008 - .010 (0.203 - 0.254) 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) 0- 8 TYP .016 - .050 (0.406 - 1.270) SO8 0303 DD Package 8-Lead Plastic DFN (3mm x 3mm) (Reference LTC DWG # 05-08-1698) R = 0.115 TYP 5 0.38 0.10 8 0.675 0.05 3.5 0.05 1.65 0.05 2.15 0.05 (2 SIDES) 3.00 0.10 (4 SIDES) PACKAGE OUTLINE 1.65 0.10 (2 SIDES) PIN 1 TOP MARK (NOTE 6) (DD8) DFN 1203 0.25 0.05 0.200 REF 0.50 BSC 2.38 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 0.75 0.05 0.00 - 0.05 4 0.25 0.05 1 0.50 BSC 2.38 0.10 (2 SIDES) BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON TOP AND BOTTOM OF PACKAGE 4257fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LTC4257 U TYPICAL APPLICATIO PD Power Interface with 3.3V, 3A Nonisolated Power Supply L1 1H J1 1 TX + 16 T1 1 TXOUT + 2 15 TX - 14 2 RX + 11 3 10 3 TXOUT - 6 RXOUT + RX - 8 6 4 7 9 XFMR RXOUT - 75 8 C3 0.01F 200V R11 75 SPARE + 5 7 TO PHY R12 75 C4 0.01F 200V 0.01F 0.01F 200V 200V 75 SPARE - + ~ + D3 TVS SMAJ58A C8 0.001F BR1 2kV DF01SA C14 0.1F 100V 3 ~ - ~ + LTC4257 NC RCLASS R13 100k Q2 FMMT625 D4 MMBZ5235B 6.8V NC NC PWRGD VIN VOUT RCLASS 1% BR2 DF01SA ~ GND C1A 4.7F 100V C1B 2.2F 100V D5 UPS840 2 - 2 T2 CTX-02-15242 RJ45 NOTES: UNLESS OTHERWISE SPECIFIED 1. ALL RESISTOR VALUES ARE 5% 2. SELECT RCLASS FOR CLASS 1-4 OPERATION. REFER TO DATA SHEET APPLICATIONS INFORMATION SECTION 3. CONNECT TO CHASSIS GROUND C1A: PANASONIC ECEV2AA4R7P C1B: TDK C5750X7R2A225KT C8: AVX 1808GC102MAT C9, C10, C12, C13: TDK C4532X5ROJ107 L1: LQLB2518T1ROM T1: PULSE H2019 R9 100k R18 10k R10 100k RUN D6 1N4148 Q4 FMMT2222 R16 100 R17 750 VIN FB INTVCC FREQ RT 80.6k 1% RC 12k CC1 1nF SENSE ITH GATE + * * LTC1871 Q1 2N7002 9 10 * 4 11 12 C9 100F X5R 6.3V C10 100F X5R 6.3V + + VOUT+ 3.3V AT 3A C12 100F X5R 6.3V C13 100F X5R 6.3V + Q3 FDC2512 MODE/SYNC GND R15 21k 1% R14 12.4k 1% C5 4.7F 6.3V C6 1F 6.3V R5 0.1 1% VOUT- 4257 TA03 RELATED PARTS PART NUMBER LTC1737 LTC1871 LTC3803 DESCRIPTION High Power Isolated Flyback Controller Wide Input Range, No RSENSETM Current Mode Flyback, Boost and SEPIC Controller Current Mode Flyback DC/DC Controller in ThinSOTTM LTC4257-1 LTC4258 IEEE 802.3af PD Interface Controller Quad IEEE 802.3af Power over Ethernet Controller LTC4259A-1 Quad IEEE 802.3af Power over Ethernet Controller LTC4267 IEEE 802.3af PD Interface Controller with Integrated Switching Regulator COMMENTS Sense Output Voltage Directly from Primary-Side Winding Adjustable Switching Frequency, Programmable Undervoltage Lockout, Optional Burst Mode(R) Operation at Light Load 200kHz Constant Frequency, Adjustable Slope Compensation, Optimized for High Input Voltage Applications 100V, 400mA Internal Switch, Dual Current Limit DC Disconnect Only, IEEE-Compliant PD Detection and Classification, Autonomous Operation or I2CTM Control AC or DC Disconnect, IEEE-Compliant PD Detection and Classification, Autonomous Operation or I2C Control 100V, 400mA Internal Switch, 16-Pin SSOP or 3mm x 5mm DFN Packages Burst Mode is a registered trademark of Linear Technology Corporation. No RSENSE and ThinSOT are trademarks of Linear Technology Corporation. 4257fb 20 Linear Technology Corporation LT 1205 REV B * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2003