NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 1 of 14 MetalR B Receptacle Connector GUARDIAN (VERIFIED BY) DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : 1.0 UNRESTRICTED OBJECTIVE This specification defines the performance, test, quality and reliability requirements of the modular metric MetralR B receptacles connector. 2.0 SCOPE This specification is applicable to the termination characteristics of the MetralR B receptacle family of products which provides a separable interconnect for printed circuit boards, and includes press-fit & solder to board receptacle connector. 3.0 GENERAL This document is composed of the following sections: 4.0 Paragraph Title 1.0 2.0 3.0 4.0 5.0 5.1 5.2 5.3 5.4 5.5 6.0 6.1 6.2 6.3 7.0 7.1 7.2 7.3 7.4 7.5 7.6 TABLE 1 8.0 OBJECTIVE SCOPE GENERAL APPLICABLE DOCUMENTS REQUIREMENTS Qualification Definitions Material Finish Design and Construction TEST METHODS AND REQUIREMENTS ELECTRICAL CHARACTERISTICS MECHANICAL CHARACTERISTICS ENVIRONMENTAL CONDITIONS QUALITY ASSURANCE PROVISIONS Equipment Calibration Inspection Conditions Sample Quantity and Description Acceptance Qualification Testing Requalification Testing QUALIFICATION TEST SEQUENCE MATRIX RECORD RETENTION APPLICABLE DOCUMENTS The following documents, of the issue in effect on the date of the latest revision of this specification, shall form a part of this specification to the extent specified herein. (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 2 of 14 MetalR B Receptacle Connector GUARDIAN (VERIFIED BY) DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : UNRESTRICTED 4.1 Scope: This product line performance is defined in several external industry standards as identified in this section. Only performance standards exceeding or not defined in these external standards will be covered in this document 4.2 Industry Product Performance Standards IEC 512: Electromechanical components for electronic equipment, basic testing procedures and measuring. IEC 707: Method of test for the determination of the flammability of solid electronic insulating material exposed to an igniting source EIA-IS64: 2mm two-part connector for printed wiring boards and backplanes EIC-364-04: Normal Force test procedure for electrical connectors Bell core GR-1217-CORE: Generic Requirements for Separable Electrical Connectors Used in Telecommunications Hardware. 4.3 AFCI Specifications: (a) General requirements from test specifications (b) Engineer Drawings (c) Process Drawings (d) GS-20-001/ BUS-20-059 Heat stake Application Specification (e) BUS-03-108 Crosstalk (f) BUS-03-110 Characteristic Impedance (g) BUS-03-111 Propagation Delay (h) BUS-03-113 Inductance (i) BUS-03-114 Capacitance (j) BUS-20-059 Application Specification (k) GS-15-002 NXTTM - Electrodeposited Amorphous Nickel With Gold Overplate (l) GS-15-011 GXT(R) & GXT+TM - Electrodeposited Deposited Palladium-Nickel Alloy With Gold Overplate 4.4 Military Specifications 4.5 Military Standards: (a) MIL-STD-202F: Test methods for electrical and electronic components (b) MIL-STD-1344A: Test methods for electrical connectors. (c) MIL-G-45204: Gold Plating (electro-deposited) (d) MIL-P-81728: SnPb Plating 4.6 U.S. Federal Specifications (a) QQ-N-290: Nickel Plating (electro-deposited) (b) UL-STD-498: Standard for attachment plugs and receptacles (c) UL-STD-94: Test for flammability of plastic materials (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 3 of 14 MetalR B Receptacle Connector GUARDIAN (VERIFIED BY) DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : 5.0 UNRESTRICTED REQUIREMENTS 5.1 Qualification U.S. Federal Specifications Connectors furnished under this specification shall be capable of meeting the qualification test requirements specified herein. 5.2 Definitions: 5.2.1 Receptacle Signal Contact Solder to Board A dual beam female right angle contacts with a solder tail for termination to the printed circuit board 5.2.2 Receptacle Power Contact Solder to Board A dual beam female right angle contacts with a solder tail for termination to the printed circuit board 5.2.3 Receptacle Insulator Housing The plastic modules in which the female contacts are retained 5.3 Material: the material for each parts shall be specified herein 5.3.1 Metallic Parts: Receptacle Contact Body: The receptacle shall be phosphor bronze alloy CuSn6 or SuSn5. 5.3.1 Insulator Parts: All receptacle housing material shall be liquid Crystal Polymer 30% glass standard IEC 707, category FV-1 5.4 Finish Contact Area: The finish for applicable components shall be as specified herein or equivalent. Reference BUS02-057. The receptacle terminals shall be plated with 30u" minimum thickness of either gold or GXTTM over 50u" minimum thickness nickel under plate .The gold deposit shall meet the requirements of MIL-G-45204, type II, Grade C and the nickel deposit shall meet the requirements of QQ-N-290, class 2.Connectors shall be of the design, construction, and physical dimensions specified on the applicable product drawing. The intended application of product to a PCB is via compliant methods CONTACT PLATING: 2.0 Micron gold / 1.3 micron min. Nickel 1.3 Micron gold / 1.3 micron min. Nickel 0.8 Micron gold / 1.3 micron min. Nickel 0.8 Micron GXT / 1.3 micron min. Nickel Solder Tail Area: Tin/Lead plating or Matte Tin plating with Nickel under-plated. 5.5 Design and Construction: The receptacle connector shall be a multi -piece assembly having 4(or 5) rows of contacts with solder tail terminations for installation in 1.48mm to 2.57mm thick printed circuit boards. The receptacle contacts shall interface with a 0.5mm male pin on a 4 or 5 row 2mm grid. (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 4 of 14 GUARDIAN (VERIFIED BY) MetalR B Receptacle Connector DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : UNRESTRICTED 5.5.1 Mating: The receptacle connectors shall be capable of mating with any appropriately constituted male connector of the same population without any degradation in performance. 5.5.2 Workmanship: Connectors shall be uniform in quality and shall be free from burrs, scratches, cracks, voids, chips, blisters, pin holes, sharp edge, and other defects that will adversely effects life or serviceability. 6.0 TEST METHODS AND REQUIREMENTS Unless otherwise specified, all inspections shall be performed under the following ambient * Temperature ---------- 20C ~ 30C * Humidity ---------------- 30% ~ 60% * Pressure --------------- Local Ambient 6.1 ELECTRICAL CHARACTERISTICS Item 6.1.1 Test Description Visual Examination Requirements Product shall meet the requirements of product drawings. Visual Examination performed under 10X magnification. Parts should be free from blistering, discoloration, cracks, etc Signal 6.1.2 LL Contact Resistance Row A Row B Row C Row D Row E EIA-364-18B Visually and functionally inspected. Under 10X magnification. Initial Resistance (Milliohms Maximum) 25 m 35 m 40 m 45 m 45 m After test : R 10 m SEE EIA-304-23C Power All Row 6.1.3 Test Methods 10 m 30 m After all mechanical and environmental tests Signal Pin 1.5 A The current carrying capacity of a mated signal pair is rated at 1.5 ampere with current applied to all contacts [24 (4 row) or 30(5 row) contacts] Power Pin Test Voltage-20 mV DC max open circuit voltage. b) Test Current - Not to exceed 100 mA. SEE EIA-IS-64 for contact resistance measurement points. Shorting contact Current Carrying Capacity a) 3.0 A The current carrying capacity of a mated power pair is rated at 3 ampere with current applied to all contacts [24 (4 row) or 30(5 row) contacts] SEE EIA-364-70 Ambient still air is 25C SEE EIA-364-70 Ambient still air is 25C (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 5 of 14 MetalR B Receptacle Connector GUARDIAN (VERIFIED BY) DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : UNRESTRICTED Measured in accordance with EIA 364-21.The following details shall apply: 6.1.4 Insulation Resistance Initially: After Tests : a.Test Voltage - 500 volts DC b. Electrification Time - 1 minute c. Points of Measurement Between adjacent contacts and between contacts and metal shields 5x103 M 1x103 M Accordance with EIA 364-20. The following details shall apply: 6.1.5 Dielectric Withstanding Voltage There shall be no evidence of arc-over, insulation breakdown, or excessive leakage current (> 0.5 milliampere) a. Test Voltage - 1000 VDC, 60Hz. b. Test Duration - 60 seconds. c. Voltage: Applied at a rate of 1000 volts per second. d. Points of Measurement Between adjacent contacts and between contacts and the metal shields The following details apply per BUS-03-114 6.1.6 Capacitance a) Connectors shall be mated and mounted onto test boards. b) Test condition: 1 MHz at 1 nsec rise time. c) Measurement equipment: Impedance analyzer or other suitable equipment capable of measuring capacitance at 1 MHz. The capacitive coupling between adjacent rows of contacts shall not exceed 3pF. The capacitive coupling between adjacent contacts within a row shall not exceed 2pF. The following details apply per BUS-03-113. 6.1.7 6.1.8 Inductance The inductance between adjacent contacts shall be no greater than 25nH, and between one contact and all other surrounding contacts grounded shall be no greater than 15nH. Propagation Delay The maximum propagation delay shall not exceed 225 psec, and the maximum row-to-row delay shall not exceed 40 psec a) Connectors shall be mated. b) Measurements shall be made from tail tip to tail tip. c) Test conditions 1 ns rise time pulse (0.0 V to 1.0 V), with a 50 Ohm termination. d) Measurements equipment : Sampler/TDR/Scope equipment with a 50 Ohm reference impedance. The following details apply per BUS-03-111 a) Connector shall be mated. b) Measurements shall be made from tail tip to tail tip. (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 6 of 14 GUARDIAN (VERIFIED BY) MetalR B Receptacle Connector DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : UNRESTRICTED c) Test Condition: 250 psec rise time pulse (0.0 V and 2 V) with a 50 Ohm termination. d) Measurements equipment: Sampler/pulse generator/scope equipment with a 50 Ohm reference impedance and 250 psec rise time The following details apply per BUS-03-108 6.1.9 6.1.10 6.2 Item 6.2.1 Cross Talk Characteristics Impedance Adjacent active/quiet near end cross talk shall not exceed 5% in any row or column combination. The far end cross talk shall nt exceed 2.5%. The mated connector characteristic impedance shall be within the range of 50-60 Ohms. The following conditions apply per BUS-03-110 a) Sample documentation; b) Sample test conditions. MECHANICAL CHARACTERISTICS Test Description Contact Retention to Housing Requirements Contact Type Total Mating Axial Force ( Minimum) 5 Newton Receptacle Contact Type 6.2.2 a) Connectors shall be mated. b) Measurements shall be made from tail tip to tail tip. c) Test Condition: 1 ns rise time pulse (0.0 V to 2.0 V) with a 50 Ohm termination. d) Measurements equipment: Sampler/Pulse Generator/Scope equipment with 50 Ohm reference impedance. Signal /Unmating Force Power There shall be no loosening of the contact or damage to the contact or damage to the connector Mating/Unmating Force/ Per Contact 0.45 Newton/Per Contact 0.15 Newton/Per Contact The total force to mate a female connector with an appropriately populated male header shall not exceed the above values times the number of contacts. Test Methods Measured in accordance with EIA-364-29. A force is applied to a contact in either direction along the axis of retention Reference - IEC 60512-13-2 or EIA- 364-13. a. Cross Head Speed 25.4 mm per minute. b. Lubrication - No c. Utilize free floating fixtures. 1.5 Newton/Per Contact 0.30 Newton/Per Contact The total force to mate a female connector with an appropriately populated male header shall not (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 7 of 14 MetalR B Receptacle Connector GUARDIAN (VERIFIED BY) DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : UNRESTRICTED exceed the above values times the number of contacts. Signal 6.2.3 6.2.4 6.2.5 Individual Contact Insertion Force Individual Contact Withdrawal Force Normal Force Press Peg Insertion/ Retention Force The individual insertion force shall not exceed 0.45 Newton Power The individual insertion force shall not exceed 1.5 Newton Signal The individual withdrawal force shall be no less than 0.15 Newton Power The individual withdrawal force shall be no less than 0.30 Newton The normal force for receptacle contacts only shall be no less than the below data after life test. Signal Power 0.4 Newton Minimum 0.8 Newton Minimum Insertion force The Insertion force shall not exceed 32 Newton. Measured in accordance with EIA-364-37 Using a maximum gage (configuration as shown in EIAIS-64), Measured in accordance with EIA-364-37 After 5 insertions of a maximum gage, the force required to withdraw a minimum gage (configuration as shown in EIAIS-64) Measured in accordance with EIA-364-04. Insert a single press peg into a plated through hole in a printed circuit board at a rate of 5.1 mm/minute. Push out at a rate of 1.0mm/minute. 6.2.6 Retention force The retention force in an axial direction opposite that of insertion shall not be less than 7 Newton. Complian Pin Insertion/Retention Force 6.2.7 Compliant Pin Insertion The force required to insert header with compliant pins into plated through holes in a printed circuit board at a rate of 0.5 inches/minute shall not exceed 65 N per pin. Per EIA-364-5 Measure force necessary to correctly apply a specimen to a printed circuit board at a maximum rate of 12.7mm per minute. (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 8 of 14 GUARDIAN (VERIFIED BY) MetalR B Receptacle Connector DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : PCB Hole Deformation Radius 6.2.8 6.2.9 6.2.10 Compliant Pin Retention Durability The average holes deformation radius of 10 holes shall be no greater than 37.5m when measured from the finished hole. The absolute maximum deformation radius shall not exceed 50m. The retention force in an axial direction opposite that of insertion shall not be less than 20 N per pin after 3 insertion/extraction cycles on the same holes. Mechanical endurance (number of mate/unmate cycles) by connector class shall be the below data. CLASS CONDITIONS CLASS I 250 CYCLES MINIMUM CLASS II 100 CYCLES MINIMUM CLASS III 30 CYCLES MINIMUM CLASS 6.2.11 CONDITIONS CLASS I 10 TO 2000 Hz AND 1,5 mm or 20g CLASS II 10 TO 500 Hz AND 0,35 mm or 5g Vibration CLASS III N/A UNRESTRICTED Reference Telcordia GR-1217CORE, section 5.1.7. Cross-section should be parallel to board surface. Photograph and measure the holes deformation radius at a point 0.25mm from the surface and at the center of the compliant pin section. Per EIA-364-5 Measure force necessary to correctly apply a specimen to a printed circuit board at a maximum rate of 12.7mm per minute. Standard laboratory procedure as applicable to the specific product EIA-364-09 Cycling Rate - 5 inches per minute Accordance with Telcordia GR1217-CORE, November 1995 a. Vibration Amplitude - 0.06" DA or 10G acceleration b. Frequency Range - 10 to 500 hertz c. Duration - 8 hours along each of three orthogonal axes (24 hours total) d. Mounting - Rigidly mount assemblies e. No discontinuities greater than 1u second (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 9 of 14 MetalR B Receptacle Connector GUARDIAN (VERIFIED BY) DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : UNRESTRICTED Accordance with Telcordia GR1217-CORE, November 1995 sections 6.3.5 and 9.1.2.1. a. Conditions - half-sine 30G, 11 millisecond duration 6.2.12 Mechanical Shock No Damage b. Shocks - 3 shocks along each of three orthogonal axes c. Mounting - Rigidly mount assemblies d. Resistance measurements taken after shock in each axis. 6.3 Item ENVIRONMENTAL CONDITIONS Test Description Requirements Test Methods Measured in accordance with 6.3.1 Thermal Shock No Damage 6.3.2 Humidity No Damage EIA 364-32A November 183, Test Condition II a. Number of Cycles - 5 b. Temperature Range Between -55 C +0C/-5C and +85 C +3C/-5C c. Time at Each Temperature 30 minutes d. Transfer Time - 5 minutes, maximum Mated samples are to be exposed to cyclical humidity and temperature in accordance with EIA-364-TP31, Method IV, with the following exceptions. Samples are to be subjected to 50 cycles of 10 hours duration for a total of 500 hours after 24 hours in a conditioning oven at 50+/2C. A cycle consists of the following steps: 1.) Ramp from 25+/-2C at 80%98% RH to 65+/-2C at 94%+/4% RH in 120 minutes 2.) Dwell at 65+/-2C at 94%+/4% RH for 4 hours (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 10 of 14 MetalR B Receptacle Connector GUARDIAN (VERIFIED BY) DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : UNRESTRICTED 3.) Ramp down to 25+/-2C at 80%-98% RH in 120 minutes 4.) Dwell at 25+/-2C at 80%98% RH for 2 hours 6.3.3 High Temperature Life No Damage Mixed Flow Gas No Damage 6.3.5 Resistance to Solder Heat Shall meet visual requirements, show no physical damage, 6.3.6 Dust Contamination 6.3.4 No Damage Telcordia GR-1217-CORE Method A, Test Condition 3. Headers and receptacles shall be mated w/o any electrical load a. Test Temperature - 85 degree C +/- 2 degree C b. Test Duration - 500 hours Samples are to be exposed to industrial gas mixture in accordance with Telcordia GR1217-CORE, November 1995, Section 9.1.3. The headers only are to be exposed for 10 days to the gas mixture detailed below, with interim resistance measurements made after the 5th and 10th days. The samples are then mated with the appropriate receptacle and exposed to an additional 10 days with resistance measurements taken after the 15th and 20th days of exposure. The test chamber is to be maintained at a temperature of 30C+/-1C with a relative humidity of 70%+/-2%. Specific please see right table Place the connector on the PCB and expose to the reflow oven. Peak Temp: 260 for 10sec. EIA-364-91A Unmated to dust composition #1 for 1 hours (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 11 of 14 MetalR B Receptacle Connector GUARDIAN (VERIFIED BY) DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : Solderability 6.3.7 (Non Eye of the Minimum solder coverage: 95 % Needle) UNRESTRICTED IEC 60512-12-1 or EIA-364-52 or ANSI-J-STD-002 or FCI GS-19037 a. Test Condition A1 (ANSI-JSTD-002) b. Steam or dry aging 4 hours 6.3.8 7.0 Acceptance criteria - (visual examination requirements and/or LLCR criteria) Salt Spray EIA-364-26 a. Test Condition :B b. Duration : 48 QUALITY ASSURANCE PROVISIONS. 7.1 Equipment Calibration All test equipment and inspection facilities used in the performance of any test shall be maintained in a calibration system in accordance with MIL-C-45662 and ISO 9000. 7.2 Inspection Conditions Unless otherwise specified herein, all inspections shall be performed under the following ambient conditions: a. Temperature: 25 +/- 5 degree C b. Relative Humidity: 30% to 60% c. Barometric Pressure: Local ambient 7.3 Sample Quantity And Description Sample quantity for each Test Group in Table 1 shall consist of a minimum of one hundred (100) contacts. The 100 contacts shall be selected from a minimum of four (4) connectors. 7.4 Acceptance 7.4.1 Electrical and mechanical requirements placed on test samples as indicated in paragraphs 6.1 and 6.2 shall be established from test data using appropriate statistical techniques or shall otherwise be customer specified, and all samples tested in accordance with this product specification shall meet the stated requirements. 7.4.2 Failures attributed to equipment, test setup, or operator error shall not disqualify the product. If product failure occurs, corrective action shall be taken and samples resubmitted for qualification. (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 12 of 14 GUARDIAN (VERIFIED BY) MetalR B Receptacle Connector DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : 7.5 UNRESTRICTED Qualification Testing Qualification testing shall be performed on sample units produced with equipment and procedures normally used in production. The test sequence shall be as specified in EIA-IS64. 7.6 Requalification Testing If any of the following conditions occur, the responsible product engineer shall initiate requalification testing consisting of all applicable parts of the Test Schedule Tables in EIA-IS64. a. A significant design change is made to the existing product, which impacts the product form, fit or function. Examples of significant changes shall include, but not be limited to, changes in the plating material composition or thickness, contact force, contact surface geometry, insulator design, contact base material, or contact lubrication requirements. b. A significant change is made to the manufacturing process, which impacts the product form, fit or function. c. A significant event occurs during production or end use requiring corrective action to be taken relative to the product design or manufacturing process. 7.7 Qualification Test Table 7.7.1 Test Table-1 (This table applies to head pins are eye of the needle type) Test Visual Examination Low Level Contact Resistance Signal contacts Low Level Contact Resistance Power contacts Current Carrying Capacity (Temperature rise vs current) Insulation Resistance Dielectric Withstanding Voltage Vibration Mechanical Shock Durability Mating/Unmating Force Para. 6.1.1 1 2 3 1,13 1,11 1,5 Test Group 4 5 6 7 8 9 10 11 Test Sequence 1,11 1,8 1,5 1,5 1,3 1.3 1,4 1,4 6.1.2 2,4,6,8,10,12 2,4,6,8,10 2,4 2,4,6,8,10 2,4 6.1.2 2,4,6,8,10,12 2,4,6,8,10 2,4 2,4,6,8,10 2,4 6.1.3 6.1.4 6.1.5 6.2.1 1 6.2.1 2 6.2.1 0 6.2.2 2 2,7 3,6 9 11 4 5 3,9 3,5 (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 13 of 14 GUARDIAN (VERIFIED BY) MetalR B Receptacle Connector DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : Contact Retention to Housing Press Peg Insertion/Retention Force Compliant pin insertion Radial hole distortion Compliant pin retention Thermal Shock Humidity High Temperature Life MFG (10 Days Unmated) MFG (10 Days Mated) Salt Spray Dust Contamination 7.7.2 6.2.6 6.2.7 6.2.8 6.2.9 6.3.1 6.3.2 6.3.3 6.3.4 6.3.4 6.3.8 6.3.6 Current Carrying Capacity (Temperature rise vs current) Insulation Resistance Dielectric Withstanding Voltage Vibration Mating/Unmating Force Contact Retention to Housing 2 2 2 3 4 3 9 4 5 3 3 2 5 7 3 7 7 Test Table-2 (This table applies to head pins are non eye of the needle type) Low Level Contact Resistance Power contacts Durability 3 6.2.1 Test Visual Examination Low Level Contact Resistance Signal contacts Mechanical Shock UNRESTRICTED 6 7 1,5 Test Group 4 5 Test Sequence 1,11 1,8 1,5 1,4 6.1.2 2,4,6,8,10,12 2,4,6,8,10 2,4 2,4,6,8,10 2,4 6.1.2 2,4,6,8,10,12 2,4,6,8,10 2,4 2,4,6,8,10 2,4 Para. 6.1.1 1 2 3 1,13 1,11 6.1.3 6.1.4 6.1.5 6.2.1 1 6.2.1 2 6.2.1 0 6.2.2 6.2.1 8 9 10 1,3 1.3 1,4 2 2,7 3,6 9 11 4 5 3,9 3,5 3 (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 NUMBER CATEGORY GS-12-453 PRODUCT SPECIFICATION TITLE PAGE REVISION C 14 of 14 GUARDIAN (VERIFIED BY) MetalR B Receptacle Connector DATE Nick Zhang 03/08/16 APPROVED BY Tim Yao CLASSIFICATION : Press Peg Insertion/Retention Force Resistance to Solder Heat Solderability Thermal Shock Humidity High Temperature Life MFG (10 Days Unmated) MFG (10 Days Mated) Salt Spray Dust Contamination 8.0 UNRESTRICTED 6.2.6 6.3.8 6.3.7 6.3.1 6.3.2 6.3.3 6.3.4 6.3.4 6.3.8 6.3.6 2 2 3 3 9 4 5 2 3 5 7 3 7 7 RECORD RETENTION REVISON RECORD REV A PAGES ALL B ALL C ALL DESCRIPTION New release according to GS-12-002 updated Update form format Update form format for Amphenol FCI EC # DG07-0105 DATE 07/04/02 DG09-0065 03/03/09 ELX-N-26297 03/08/16 (c) 2016 AFCI Form E-3334 Rev J GS-01-001 PDS: Rev :C STATUS:Released Printed: Mar 08, 2017 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: FCI / Amphenol: 85876-112LF 89095-102LF 89093-102LF 88946-302LF 88945-302LF 63793-101LF 89039-111LF 88947-102LF 88945-102LF 94561-111LF 88949-102LF 85863-102LF 85863-112LF 85864-102LF 85865-102LF 85865-112LF 85866-102LF 85876-102LF 88945-112LF 88945-202LF 88946-112LF 89038-102LF 89039-101LF 89093-112LF 89094-112LF 89095-112LF 89036-112LF