NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Features * VDD=VDDQ=1.5V +0.1275V/-0.075V * 1k page size for x 4 & x 8, 2k page size for x16 * Pseudo 1.8V I/O * Data-Strobes: Bidirectional, Differential * 8 internal memory banks * Strong and Weak Strength Data-Output Driver * Programmable CAS Latency: 3, 4, 5, and 6 * Auto-Refresh and Self-Refresh * Programmable Additive Latency: 0, 1, 2, 3, 4 and 5 * Power Saving Power-Down modes * Write Latency = Read Latency -1 * 7.8 s max. Average Periodic Refresh Interval * Programmable Burst Length: 4 and 8 * OCD (Off-Chip Driver Impedance Adjustment) * Packages: 60 Ball BGA for x4/x8 components 84 Ball BGA for x16 component * ODT (On-Die Termination) * RoHS Compliance * Programmable Sequential / Interleave Burst * 4 bit prefetch architecture Description The 1Gb Double-Data-Rate-2 (DDR2) DRAMs is a highspeed CMOS Double Data Rate 2 SDRAM containing 1,073,741,824 bits. It is internally configured as a octal-bank DRAM. The 1Gb chip is organized as either 32Mbit x 4 I/O x 8 bank, 16Mbit x 8 I/O x 8 bank or 8Mbit x 16 I/O x 8 bank device. The chip is designed to comply with all key DDR2 DRAM key features: (1) posted CAS with additive latency, (2) write latency = read latency -1, (3) normal and weak strength dataoutput driver, (4) variable data-output impedance adjustment and (5) an ODT (On-Die Termination) function. All of the control and address inputs are synchronized with a pair of externally supplied differential clocks. Inputs are latched at the cross point of differential clocks (CK rising and CK falling). All I/Os are synchronized with a single ended DQS or differential DQS pair in a source synchronous fashion. A 14 bit address bus for x4 and x8 organised components and a 13 bit address bus for x16 components is used to convey row, column, and bank address devices. These devices operate with a single 1.5V +0.1275V/-0.075V power supply and are available in BGA packages. An Auto-Refresh and Self-Refresh mode is provided along with various power-saving power-down modes. REV 1.3 09/2009 1 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Pin Configuration - 60 balls 0.8mmx0.8mm Pitch BGA Package (x4/x8) <Top View > See the balls through the package. x4 1 2 3 7 8 9 VDD NC VSS A VSSQ DQS VDDQ NC VSSQ DM B DQS VSSQ NC VDDQ DQ1 VDDQ C VDDQ DQ0 VDDQ NC VSSQ DQ3 D DQ2 VSSQ NC VDDL VREF VSS E VSSDL CK VDD CKE WE F RAS CK ODT BA0 BA1 G CAS CS A10/AP A1 H A2 A0 A3 A5 J A6 A4 A7 A9 K A11 A8 A12 NC L NC A13 BA2 VSS VDD VDD VSS x8 1 2 3 7 8 9 VDD NU,/RDQS VSS A VSSQ DQS VDDQ DQ6 VSSQ DM/RDQS B DQS VSSQ DQ7 VDDQ DQ1 VDDQ C VDDQ DQ0 VDDQ DQ4 VSSQ DQ3 D DQ2 VSSQ DQ5 VDDL VREF VSS E VSSDL CK VDD CKE WE F RAS CK ODT BA0 BA1 G CAS CS A10/AP A1 H A2 A0 A3 A5 J A6 A4 A7 A9 K A11 A8 A12 NC L NC A13 BA2 VSS VDD REV 1.3 09/2009 VDD VSS 2 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Pin Configuration - 84 balls 0.8mmx0.8mm Pitch BGA Package (x16) <Top View > See the balls through the package. x 16 1 2 3 7 8 9 VDD NC VSS A VSSQ UDQS VDDQ DQ14 VSSQ UDM B UDQS VSSQ DQ15 VDDQ DQ9 VDDQ C VDDQ DQ8 VDDQ DQ12 VSSQ DQ11 D DQ10 VSSQ DQ13 VDD NC VSS E VSSQ LDQS VDDQ DQ6 VSSQ LDM F LDQS VSSQ DQ7 VDDQ DQ1 VDDQ G VDDQ DQ0 VDDQ DQ4 VSSQ DQ3 H DQ2 VSSQ DQ5 VDDL VREF VSS J VSSDL CK VDD CKE WE K RAS CK ODT BA0 BA1 L CAS CS A10/AP A1 M A2 A0 A3 A5 N A6 A4 A7 A9 P A11 A8 A12 NC R NC NC BA2 VSS VDD REV 1.3 09/2009 VDD VSS 3 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Input/Output Functional Description Symbol Type Function Input Clock: CK and CK are differential clock inputs. All address and control input signals are sampled on the crossing of the positive edge of CK and negative edge of CK. Output (read) data is referenced to the crossings of CK and CK (both directions of crossing). CKE Input Clock Enable: CKE high activates and CKE low deactivates internal clock signals and device input buffers and output drivers. Taking CKE low provides Precharge Power-Down and SelfRefresh operation (all banks idle), or Active Power-Down (row Active in any bank). CKE is synchronous for power down entry and exit and for Self-Refresh entry. CKE is asynchronous for SelfRefresh exit. CKE must be maintained high throughout read and write accesses. Input buffers, excluding CK, CK, ODT and CKE are disabled during Power Down. Input buffers, excluding CKE are disabled during Self-Refresh. CS Input Chip Select: All command are masked when CS is registered high. CS provides for external rank selection on systems with multiple memory ranks. CS is considered part of the command code. RAS, CAS, WE Input Command Inputs: RAS, CAS and WE (along with CS) define the command being entered. DM (LDM, UDM) Input Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is sampled high coincident with that input data during a Write access. DM is sampled on both edges of DQS. Although DM pins are input only, the DM loading matches the DQ and DQS loading. For x8 device, the function of DM or RDQS / RQDS is enabled by EMRS command to EMR(1). BA0-BA2 Input Bank Address Inputs: BA0 - BA2 define to which bank an Active, Read, Write or Precharge command is being applied. Bank address also determines if the mode register or one of the extended mode registers is to be accessed during a MRS or EMR command cycle. A0 - A13 Input Address Inputs: Provides the row address for Activate commands and the column address and Auto-Precharge bit for Read/Write commands to select one location out of the memory array in the respective bank. A10 is sampled during a Precharge command to determine whether the Precharge applies to one bank (A10 LOW) or all banks (A10 HIGH). If only one bank is to be precharged, the bank is selected by BA0 - BA2. The address inputs also provide the op-code during MRS or EMRS command. DQ Input/Output Data Inputs/Output: Bi-directional data bus. Input/Output Data Strobe: output with read data, input with write data. Edge aligned with read data, centered in write data. For the x16, LDQS corresponds to the data on DDQ0 - DQ7; UDQS corresponds to the data on DQ8-DQ15. For the x8, an RDQS option using DM pin can be enabled via the EMR(1) to simplify reading time. The data strobes DQS, LDQS, UDQS, and RDQS may be used in single ended mode or paired with the optional complementary signals DQS, LDQS, UDQS, and RDQS to provide differential pair signaling to the system during both reads and writes. A control bit at EMR(1)[A10] control bit enables or disables the complementary data strobe signals. Input On Die Termination: ODT (registered HIGH) enables termination resistance internal to the DDR2 SDRAM. When enabled, ODT is applied to each DQ, DQS, DQS and DM signal for x4 and DQ, DQS, DQS, RDQS, RDQS and DM for x4/x8 configurations. For x16 configuration ODT is applied to each DQ, UDQS, UDQS, LDQS, LDQS, UDM and LDM signal. The ODT pin will be ignored if the EMR(1) is programmed to disable ODT. CK, CK DQS, (DQS), (LDQS), (LDQS), (UDQS), (UDQS), (RDQS), (RDQS) ODT No Connect: No internal electrical connection is present. NC VDDQ Supply DQ Power Supply: +1.5V +0.1275V/-0.075V VSSQ Supply DQ Ground VDDL Supply DLL Power Supply: +1.5V +0.1275V/-0.075V VSSDL Supply DLL Ground VDD Supply Power Supply: +1.5V +0.1275V/-0.075V VSS Supply Ground VREF Supply Vref = VDDQ/2 REV 1.3 09/2009 4 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Ordering Information Speed Org. Part Number Package Clock (MHz) CL-tRCD-tRP NT5TB256M4DE-37B 266 4-4-4 NT5TB256M4DE-3C 333 5-5-5 NT5TB256M4DE-AD 400 6-6-6 400 5-5-5 266 4-4-4 NT5TB128M8DE-3C 333 5-5-5 NT5TB128M8DE-AD 400 6-6-6 NT5TB128M8DE-AC 400 5-5-5 NT5TB64M16DG-37B 266 4-4-4 333 5-5-5 400 6-6-6 400 5-5-5 256M x 4 NT5TB256M4DE-AC NT5TB128M8DE-37B 60ball BGA 0.8mmx0.8mm Pitch 128M x 8 NT5TB64M16DG-3C 64M x 16 NT5TB64M16DG-AD NT5TB64M16DG-AC 84ball BGA 0.8mmx0.8mm Pitch Note: REV 1.3 09/2009 5 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Block Diagram (256Mb x 4) Control Logic CKE CK CK CS Command Decode WE CAS RAS Row-Address MUX Mode Registers 17 14 14 CK, CK DLL 4 16 8 8192 4 2 DQS Generator DQ0 - DQ3 DQS, DQS 3 I/O Gating DM Mask Logic Bank Control Logic COL0,1 Input Register 512 (x16) 16 Mask 4 Write FIFO & Drivers Data 9 Column-Address Counter/Latch 2 16 COL0,1 Notes: 1. This Functional Block Diagram is intended to facilitate user understanding of the operation of the device; it does not represent an actual circuit implementation. 2. DM is an unidirectional signal (input only), but it is internally loaded to match the load of the bidirectional DQ and DQS signals. CK, CK 1 1 1 1 1 1 1 1 4 4 4 4 4 4 4 4 DQS, DQS 1 Receivers Column Column Decoder Column Decoder Column Decoder Column Decoder Column Decoder Column Decoder Column Decoder Decoder 8 11 09/2009 4 MUX 16 3 REV 1.3 4 ODT Control Refresh Counter A0 - A13, BA0 - BA2 Address Register 17 ODT Data 4 Drivers 14 Bank 7 Bank 6 Bank 5 Bank 4 Bank 3 Bank 2 Array Memory Bank 1 Array Memory (16384 x512 x16) Bank 0 Memory Arrayx16) (16384 Sensex512 Amplifier Memory Array (16384 x16) Sensex512 Amplifier Memory Array (16384 x512 x16) Sense Amplifier Memory Arrayx16) (16384 x512 SenseArray Amplifier Memory (16384 x16) Sensex512 Amplifier Memory Array (16384 x16) Sensex512 Amplifier (16384 x512 x16) Sense Amplifier Sense Amplifier Read Latch Bank 7 Bank 6 Bank 5 Bank 4 Bank 3 Bank 2 Row-Address Bank 1 Row-Address Bank 0Latch & Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address 16384 Latch & Decoder Latch & Decoder Decoder DM 4 COL0,1 6 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Block Diagram (128Mb x 8) Control Logic CKE CK CK CS Command Decode WE CAS RAS Row-Address MUX Mode Registers 17 14 14 CK, CK DLL 8 32 8 8192 8 2 DQS Generator DQ0 - DQ7 DQS, DQS 3 I/O Gating DM Mask Logic Bank Control Logic COL0,1 Input Register 1 1 256 (x32) 32 Mask 4 Write FIFO & Drivers Data 8 Column-Address Counter/Latch 2 32 COL0,1 Notes: 1. This Functional Block Diagram is intended to facilitate user understanding of the operation of the device; it does not represent an actual circuit implementation. 2. DM is an unidirectional signal (input only), but it is internally loaded to match the load of the bidirectional DQ and DQS signals. CK, CK 1 1 1 1 1 1 8 8 8 8 8 8 8 8 DQS, DQS 1 Receivers Column Column Decoder Column Decoder Column Decoder Column Decoder Column Decoder Column Decoder Column Decoder Decoder 8 10 09/2009 8 MUX 32 3 REV 1.3 8 ODT Control Refresh Counter A0 - A13, BA0 - BA2 Address Register 17 ODT Data 8 Drivers 14 Bank 7 Bank 6 Bank 5 Bank 4 Bank 3 Bank 2 Array Memory Bank 1 Array Memory (16384 x16) Bank 0 x512 Memory Arrayx16) (16384 Sensex512 Amplifier Memory Array (16384 x512 x16) SenseArray Amplifier Memory (16384 x16) Sensex512 Amplifier Memory Array (16384 x16) Sensex512 Amplifier Memory Array (16384 x512 x16) SenseArray Amplifier Memory (16384 x16) Sensex512 Amplifier (16384 x32) Sensex256 Amplifier Sense Amplifier Read Latch Bank 7 Bank 6 Bank 5 Bank 4 Bank 3 Bank 2 Row-Address Bank 1 Row-Address Bank 0Latch & Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address 16384 Latch & Decoder Latch & Decoder Decoder DM 8 COL0,1 7 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Block Diagram (64Mb x 16) Control Logic CKE CK CK CS Command Decode WE CAS RAS Row-Address MUX Mode Registers 16 13 13 CK, CK DLL 16 64 8 16384 16 4 DQS Generator DQ0 - DQ15 DQS, DQS 3 I/O Gating DM Mask Logic Bank Control Logic COL0,1 2 Input Register 2 64 Mask 2 2 8 2 2 Write FIFO & Drivers Data 64 COL0,1 Notes: 1. This Functional Block Diagram is intended to facilitate user understanding of the operation of the device; it does not represent an actual circuit implementation. 2. DM is an unidirectional signal (input only), but it is internally loaded to match the load of the bidirectional DQ and DQS signals. CK, CK UDQS, UDQS LDQS, LDQS 2 2 2 16 16 16 16 16 16 16 16 Receivers Column Column Decoder Column Decoder Column Decoder Column Decoder Column Decoder Column Decoder Column Decoder Decoder 8 Column-Address Counter/Latch 2 256 (x64) 8 10 09/2009 16 MUX 64 3 REV 1.3 16 ODT Control Refresh Counter A0 - A12, BA0 - BA2 Address Register 16 ODT Data 16 Drivers 13 Bank 7 Bank 6 Bank 5 Bank 4 Bank 3 Bank 2 Array Memory Bank 1 Array Memory (16384 x16) Bank 0 x512 Memory Arrayx16) (16384 Sensex512 Amplifier Memory Array (16384 x16) Sensex512 Amplifier Memory Array (16384 x16) Sensex512 Amplifier Memory Array (16384 x16) Sensex512 Amplifier Memory Array (16384 x16) Sensex512 Amplifier Memory Array (16384 x16) Sensex512 Amplifier (8192 x 86 x 64) Sense Amplifier Sense Amplifier Read Latch Bank 7 Bank 6 Bank 5 Bank 4 Bank 3 Bank 2 Row-Address Bank 1 Row-Address Bank 0Latch & Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address Latch & Decoder Row-Address 8192 Latch & Decoder Latch & Decoder Decoder UDM, LDM 16 COL0,1 8 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Basic Functionality Read and write accesses to the DDR2 SDRAM are burst oriented; accesses start at a selected location and continue for a burst length of four or eight in a programmed sequence. Accesses begin with the registration of an Activate command, which is then followed by a Read or Write command. The address bits registered coincident with the activate command are used to select the bank and row to be accesses (BA0 & BA1 select the banks, A0-A13 select the row for x4 and x8 components, A0~A12 select the row for x16 components). The address bits registered coincident with the Read or Write command are used to select the starting column location for the burst access and to determine if the Auto-Precharge command is to be issued. Prior to normal operation, the DDR2 SDRAM must be initialized. The following sections provide detailed information covering device initialization, register definition, command description and device operation. Initialization DDR2 SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than those specified may result in undefined operation. For DDR2 SDRAMs, both bits BA0 and BA1 must be decoded for Mode/Extended Mode Register Set (MRS/EMR) commands. Users must initialize all four mode Registers. The registers maybe initialized in any order. The following sequence is required for POWER UP and Initialization. 1. Either one of the following sequence is required for Power-up. 1(a). While applying power and attempt to maintain CKE below 0.2 * VDDQ and ODT at a low state (all other inputs may be undefined). The VDD voltage ramp time must be no greater than 200ms from when VDD ramps from 300mV to VDD min; and during the VDD voltage ramp, lVDD-VDDQl<=0.3V. Once the ramping of the supply voltages is complete (when VDDQ crosses VDDQ min). - VDD,VDDL, and VDDQ are driven from a signle power converter output, AND - VTT is limited to 0.95 V max, AND - VREF tracks VDDQ/2, VREF must be within +/- 300mV with respect to VDDQ/2 during supply ramp time. - VDDQ>=VREF must be met at all times. or 1(b). While applying power and attempt to maintain CKE below 0.2 * VDDQ and ODT at a low state, all other inputs may be undefined, voltage levels at I/Os and outputs must be less than VDDQ during voltage ramp time to avoid DRAM latch-up. During the ramping of the supply voltages, VDD>=VDDL>=VDDQ must be maintained and is applicable to both AC and DC levels until the ramping of the supply voltages is complete, which is when VDDQ crosses VDDQ min. - Apply VDD/VDDL before or at the same time as VDDQ, - VDD/VDDL voltage ramp time must be no greater than 200ms from when VDD ramps from 300mV to VDD min. - Apply VDDQ before or at the same time as VTT. - The VDDQ voltage ramp time from when VDD min is achieved on VDD to when VDDQ min is achieved on VDDQ must be no greater than 500ms. (Note: While VDD is ramping, current may be supplied from VDD through the DRAM to VDDQ.) - Vref must track VDDQ/2, Vref must be within +/-300mV with respect to VDDQ/2 during supply ramp time. - VDDQ>=VREF must be met at all times. - Apply VTT. - The VTT voltage ramp time from when VDDQ min is achieved on VDDQ to when VTT min is achieved on VTT must be greater than 500ms. 2. Start clock (CK, CK) and maintain stable condition. 3. For the minimum of 200us after stable power (VDD, VDDL, VDDQ, VREF, and VTT are between their minimum and maxi 4. Wait minimum of 400ns, then issue Precharge-all command. NOP or Deselect applied during 400us period. 5. Issue EMR(2) command. (To issue EMR(2) command, provide "low" to BA0 and BA2 and "high" to BA1) 6. Issue EMR(3) command. (To issue EMR(3) command, provide "low" to BA2 and "high" to BA0 and BA1) 7. Issue EMRS to enable DLL. (To issue "DLL Enable" command, provide "low" to A0 and "high" to BA0 and "low" to BA1-BA2 and A13-A15. And A9=A8=A7=LOW must be used when issuing this command.) REV 1.3 09/2009 9 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die 8. Issue MRS command (Mode Register Set) for "DLL reset". (To issue DLL reset command, provide "high" to A8 and "low" to BA0 ~ BA2 and A13 ~ A15) 9. Issue Precharge-All command. 10. Issue 2 or more Auto-Refresh commands. 11. Issue a MRS command with LOW on A8 to initialize device operation. (i.e. to programm operating paramters with out resetting the DLL) 12. At least 200 clocks after step 8, execute OCD Calibration (Off Chip Driver impedance adjustment). If OCD calibration is not used, EMRS to EMR(1) to set OCD Default (A9=A8=A7=HIGH) followed by EMRS to EMR(1) OCD Calibra tion Mode Exit command (A9=A8=A7=LOW) must be issued with other parameters of EMR(1). 13. The DDR2 SDRAM is now read for normal operation. Example CK, CK CKE ODT "low" NOP Command tMRS tRP 400 ns PRE ALL CMD EMRS Extended Mode Register Set with DLL enable tRP tMRS MRS Mode Register Set with DLL reset PRE ALL CMD tRFC tRFC 1st Auto refresh min. 200 cycles to lock the DLL 2nd Auto refresh tMRS MRS EMRS OCD Follow OCD flowchart Register Definition Programming the Mode Register and Extended Mode Registers For application flexibility, burst length, burst type, CAS latency, DLL reset function, write recovery time (tWR) are user defined variables and must be programmed with a Mode Register Set (MRS) command. Additionally, DLL disable function, additive CAS latency, driver impedance, ODT (On Die Termination), single-ended strobe and OCD (off chip driver impedance adjustment) are also user defined variables and must be programmed with an Extended Mode Register Set (EMRS) command. Contents of the Mode Register (MR) and Extended Mode Registers (EMR(#)) can be altered by re-executing the MRS and EMRS Commands. If the user chooses to modify only a subset of the MRS or EMRS variables, all variables must be redefined when the MRS or EMRS commands are issued. MRS, EMRS and DLL Reset do not affect array contents, which means reinitializazion including those can be executed any time after power-up without affecting array contents. Mode Register Set (MRS) The mode register stores the data for controlling the various operating modes of DDR2 SDRAM. It contorls CAS latency, burst length, burst sequence, test mode, DLL reset, tWR and various vendor specific options to make DDR2 SDRAM useful for various applications. The default value of the mode register is not defined, therefore the mode register must be written after powerup for proper operation. The mode register is written by asserting low on CS, RAS, CAS, WE, BA0 and BA1, while controlling the state of address pins A0 ~ A13. The DDR2 SDRAM should be in all bank precharged (idle) mode with CKE already high prior to writing into the mode register. The mode register set command cycle time (tMRD) is required to complete the write operation to the mode register. The mode register contents can be changed using the same command and clock cycle requirements during normal operation as long as all banks are in the precharged state. The mode register is divided into various fields depending on functionality. Burst length is defined by A0 ~ A2 with options of 4 and 8 bit burst length. Burst address sequence type is defined by A3 and CAS latency is defined by A4 ~ A6. A7 is used for test mode and must be set to low for normal MRS operation. A8 is used for DLL reset. A9 ~ A11 are used for write recovery time (WR) definition for Auto-Precharge mode. REV 1.3 09/2009 10 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die MRS Mode Register Operation Table (Address Input For Mode Set) Address Filed BA2* BA1 BA0 A13* A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Burst Length MRS mode A2 A1 A0 BL BA1 BA0 MRS mode 0 1 0 4 0 1 1 8 0 0 MR 0 1 EMR(1) 1 0 EMR(2) A3 Burst Type 1 1 EMR(3) 0 Sequential 1 Interleave Burst Type Active power down exit time Active power down A12 exit time /CAS Latency 0 Fast exit (use tXARD) A6 A5 A4 CAS Latency 1 Slow exit (use tXARDS) 0 0 0 Reserved Write recovery for autoprecharge 0 0 1 Reserved A11 A10 A9 WR(cycles) 0 1 0 Reserved 0 Reserved 0 1 1 3 0 0 1 2 1 0 0 4 0 1 0 3 1 0 1 5 0 1 1 4 1 1 0 6 1 0 0 5 1 1 1 Reserved 1 0 1 6 1 1 0 Reserved 1 1 1 Reserved DDR2-800 0 DDR2-533 DDR2-667 0 Mode A7 Mode 0 Normal 1 TEST DLL Reset A8 DLL Reset 0 NO 1 YES REV 1.3 09/2009 * BA2 and A13 are reserved for future use and must be set to 0 when programming the MR. 11 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die EMR(1) Extended Mode Register Set Programming Address Filed BA2* BA1 BA0 A13 * A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 DLL MRS mode BA1 BA0 MRS mode A0 DLL Enable 0 Enable 1 Disable 0 0 MR 0 1 EMR(1) 1 0 EMR(2) 1 1 EMR(3) 0 Full strength Qoff 1 Reduced strength D.I.C Output Driver A1 Impedance Control A12 Qoff*3 0 Output buffer enabled A6 A2 Rtt (Nominal) 1 Output buffer disabled 0 0 ODT Disabled RDQS 0 1 75 ohm 1 0 150 ohm 1 1 50 ohm Rtt A11 RDQS Enable*4 /DQS 0 Enable A10 /DQS 1 Disable 0 Enable 1 Disable A5 OCD Program A9 A8 A7 OCD Calibration Program OCD Calibration mode exit; maintain setting Additive Latency Additive A4 A3 Latency 0 0 0 0 0 0 1 1 0 1 0 2 0 1 1 3 0 0 0 0 0 1 Drive(1) 1 0 0 4 0 1 0 Drive(0) 1 0 1 5 1 0 0 Adjust mode *1 1 1 0 Reserved 1 1 1 1 1 1 Reserved OCD Calibration default*2 * BA2 and A13 are reserved for future use and must be set to 0 when programming the MR. *1 When Adjust mode is issued. AL from previously set value must be applied. *2 After setting to default, OCD calibration mode needs to be exited by setting A9~A7 to 000. *3 Output disabled - DQs, DQSs, /DQSs, RDQS, /RDQS. This feature is used in conjunction with DIMM IDD measurements when IDDQ is not desired to be included. *4 If RDQS is enabled, the DM function is disabled. RDQS is active for reads and do not care for writes. REV 1.3 09/2009 12 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Extended Mode Register Set (EMR(1)) The extended mode register EMR(1) stores the data for enabling or disabling the DLL, output driver strength, additive latency, ODT, DQS disable, OCD program, RQDS enable. The default value of the extended mode register EMR(1) is not defined, therefore the extended mode register must be written after power-up for proper operation. The extended mode register is written by asserting low on CS, RAS, CAS, WE, BA1 and high on BA0, while controlling the state of the address pins. The DDR2 SDRAM should be in all bank precharge with CKE already high prior to writing into the extended mode register. The mode register set command cycle time (tMRD) must be satisfied to complete the write operation to the EMR(1). Mode register contents can be changed using the same command and clock cycle requirements during normal operation as long as all banks are in precharge state. A0 is used for DLL enable or disable. A1 is used for enabling a half strength output driver. A3-A5 determine the additive latency, A7-A9 are used for OCD control, A10 is used for DQS disable and A11 is used for RDQS enable. A2 and A6 are used for ODT setting. Single-ended and Differential Data Strobe Signals The following table lists all possible combinations for DQS, DQS, RDQS, RQDS which can be programmed by A10 & A11 address bits in EMRS. RDQS and RDQS are available in x8 components only. If RDQS is enabled in x8 components, the DM function is disabled. RDQS is active for reads and don't care for writes : EMRS Stobe Function Matrix Signaling A11 (RDQS Enable) A10 (DQS Enable) RDQS/DM RDQS DQS DQS 0 (Disable) 0 (Enable) DM Hi-Z DQS DQS differential DQS signals 0 (Disable) 1 (Disable) DM Hi-Z DQS Hi-Z single-ended DQS signals 1 (Enable) 0 (Enable) RDQS RDQS DQS DQS differential DQS signals 1 (Enable) 1 (Disable) RDQS Hi-Z DQS Hi-Z single-ended DQS signals DLL Enable/Disable The DLL must be enabled for normal operation. DLL enable is required during power up initialization, and upon returning to normal operation after having the DLL disabled. The DLL is automatically disabled when entering Self-Refresh operation and is automatically re-enabled and reset upon exit of Self-Refresh operation. Any time the DLL is reset, 200 clock cycles must occur before a Read command can be issued to allow time for the internal clock to be synchronized with the external clock. Less clock cycles may result in a violation of the tAC or tDQSCK parameters. Output Disable (Qoff) Under normal operation, the DRAM outputs are enabled during Read operation for driving data (Qoff bit in the EMR(1) is set to 0). When the Qoff bit is set to 1, the DRAM outputs will be disabled. Disabling the DRAM outputs allows users to measure IDD currents during Read operations, without including the output buffer current. EMR(2) The Extended mode Register EMR(2) controls refresh related features. The default value of EMRS(2) is not defined; therefore, EMR(2) must be writeen after power-up for proper operation. EMR(2) is written by asserting low on CS,RAS,CAS,WE, high on BA1 and low on BA0, while controlloing the states of address pins A0~A15. The DDR2 SDRAM should be in all bank percharge with CKE already high prior to writing into EMR(2). The mode register set command cycle time (tMRD) must be satisfied to complete the write operation to EMR(2). Mode register contents can be changed using the same command and clock cycle requirements during normal operation as long as all banks are in the percharge state. REV 1.3 09/2009 13 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die EMR(2) Extended Mode Register Operation Table (Address Input For Mode Set) BA2 BA1 BA0 A12 A11 A10 0* 0* 0 1 BA1 BA0 A9 A8 A7 A6 A7 A4 A3 A2 0* SRF MRS mode A5 A1 A0 PASR*** Address Field Extended Mode Register High Temperature Self-Refresh Rate Enable 0 0 MRS 0 Disable 0 1 EMR(1) 1 Enable** (85C Tcase 95C) 1 0 EMR(2) 1 1 EMR(3) A2 A1 A0 0 0 0 Full array 0 0 1 Half Array (BA[2:0]=000, 001, 010, &011) 0 1 0 Quarter Array (BA[2:0]=000&001) 0 1 1 1/8th array (BA[2:0] = 000) 1 0 0 3 / 4 array (BA[2:0]=010,011,100,101,110, &111) 1 0 1 Half array (BA[2:0]=100, 101, 110, & 111) 1 1 0 Quarter array (BA[2:0]=110&111) 1 1 1 1/8th array (BA[2:0]=111) Partial Array Self Refresh * The rest bits in EMRS(2) is reserved for future use and all bits in EMRS(2) except A0-A2,A7,BA0, and BA1 must be programmed to 0 when setting EMRS(2) during initialization. ** DDR2 SDRAM Module user can look at module SPD field Byte 49 bit [0]. *** Optional. If PASR(Partial Array Self Refresh) is enabled, data located in areas of the array beyond the spec. location will be lost if self refresh is entered. EMR(3) Extended Mode Registers The Extended Mode Registers EMR(3) are reserved for future use and all bits except BA0 and BA1 must be programmed to 0 when setting the mode register during initialization. REV 1.3 09/2009 14 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Off-Chip Driver (OCD) Impedance Adjustment DDR2 SDRAM supports driver calibration feature and the flow chart below is an example of the sequence. Every calibration mode command should be followed by "OCD calibration mode exit" before any other command being issued. MRS should be set before entering OCD impedance adjustment and ODT (On Die Termination) should be carefully controlled depending on system environment. MRS should be set before entering OCD impedance adjustment and ODT should be carefully controlled depending on system environment Start EMRS: OCD calibration mode exit EMRS: Drive (1) EMRS: Drive(0) DQ & DQS High; DQS Low DQ & DQS Low; DQS High ALL OK ALL OK Test Test Need Calibration Need Calibration EMRS: OCD calibration mode exit EMRS: OCD calibration mode exit EMRS : EMRS : Enter Adjus t Mode Enter Adjust Mode BL=4 cod e inpu t to all DQs BL =4 code input to all DQs Inc, Dec, or NOP Inc, Dec, or NOP EMRS: OCD calibration mode exit EMRS: OCD calibration mode exit EMRS: OCD calibration mode exit End REV 1.3 09/2009 15 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Extended Mode Register Set for OCD impedance adjustment OCD impedance adjustment can be done using the following EMR(1) mode. In drive mode all outputs are driven out by DDR2 SDRAM and drive of RDQS is dependent on EMR(1) bit enabling RDQS operation. In Drive(1) mode, all DQ, DQS (and RDQS) signals are driven high and all DQS (and RDQS) signals are driven low. In Drive(0) mode, all DQ, DQS (and RDQS) signals are driven low and all DQS (and RDQS) signals are driven high. In adjust mode, BL = 4 of operation code data must be used. In case of OCD calibration default, output driver characteristics have a nominal impedance value of 18 Ohms during nominal temperature and voltage conditions. Output driver characteristics for OCD calibration default are specified in the following table. OCD applies only to normal full strength output drive setting defined by EMR(1) and if half strength is set, OCD default driver characteristics are not applicable. When OCD calibration adjust mode is used, OCD default output driver characteristics are not applicable. After OCD calibration is completed or driver strength is set to default, subsequent EMR(1) commands not intended to adjust OCD characteristics must specify A7~A9 as '000' in order to maintain the default or calibrated value. Off- Chip-Driver program A9 0 0 0 1 1 A8 0 0 1 0 1 A7 0 1 0 0 1 Operation OCD calibration mode exit Drive(1) DQ, DQS, (RDQS) high and DQS, (RDQS) low Drive(0) DQ, DQS, (RDQS) low and DQS, (RDQS) high Adjust mode OCD calibration default OCD impedance adjust To adjust output driver impedance, controllers must issue the ADJUST EMR(1) command along with a 4 bit burst code to DDR2 SDRAM as in the following table. For this operation, Burst Length has to be set to BL = 4 via MRS command before activating OCD and controllers must drive the burst code to all DQs at the same time. DT0 is the table means all DQ bits at bit time 0, DT1 at bit time 1, and so forth. The driver output impedance is adjusted for all DDR2 SDRAM DQs simultaneously and after OCD calibration, all DQs of a given DDR2 SDRAM will be adjusted to the same driver strength setting. The maximum step count for adjustment can be up to 16 and when the limit is reached, further increment or decrement code has no effect. The default setting may be any step within the maximum step count range. When Adjust mode command is issued, AL from previously set value must be applied. Off- Chip-Driver Adjust Program 4 bit burst code inputs to all DQs DT0 DT1 DT2 DT3 0 0 0 0 1 0 0 1 1 0 0 0 0 1 0 0 1 0 0 0 1 1 1 0 0 1 0 Other Combinations 0 1 0 0 0 1 0 1 0 Operation Pull-up driver strength NOP (no operation) Pull-down driver strength NOP (no operation) Increase by 1 step NOP Decrease by 1 step NOP NOP Increase by 1 step NOP Decrease by 1 step Increase by 1 step Increase by 1 step Decrease by 1 step Increase by 1 step Increase by 1 step Decrease by 1 step Decrease by 1 step Decrease by 1 step Reserved Reserved For proper operation of adjust mode, WL = RL - 1 = AL + CL -1 clocks and tDS / tDH should be met as the following timing diagram. Input data pattern for adjustment, DT0 - DT3 is fixed and not affected by MRS addressing mode (i.e. sequential or interleave). REV 1.3 09/2009 16 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die OCD Adjust Mode OCD calibration mode exit OCD adjust mode CK CK EMRS CMD NOP NOP NOP NOP DQS WL NOP EMRS NOP WR DQS tDS DQ tDH DT0 DT1 DT2 DT3 DM Drive Mode Drive mode, both Drive(1) and Drive(0), is used for controllers to measure DDR2 SDRAM Driver impedance before OCD impedance adjustment. In this mode, all outputs are driven out tOIT after "enter drive mode" command and all output drivers are turned-off tOIT after "OCD calibration mode exit" command as the following timing diagram. CK, CK CMD EMRS NOP NOP NOP NOP NOP NOP NOP tOIT tOIT DQS_in EMRS DQS high & DQS low for Drive(1), DQS low & DQS high for Drive 0 DQS high for Drive(1) DQS high for Drive(0) DQ_in OCD calibration mode exit Enter Drive Mode REV 1.3 09/2009 17 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die On-Die Termination (ODT) ODT (On-Die Termination) is a feature that allows a DRAM to turn on/off termination resistance for each DQ, DQ, DQS, DQS, RDQS, RDQS, and DM signal for x4/x8 configurations via the ODT control pin. For x16 configuration ODT is applied to each DQ, UDQS, UDQS, LDQS, LDQS, UDM and LDM signal via the ODT control pin. The ODT feature is designed to improve signal integrity of the memory channel by allowing the DRAM controller to independently turn on/off termination resistance for any or all DRAM devices. The ODT function can be used for all active and standby modes. ODT is turned off and not supported in Self-Refresh mode. Funtional Prepresentation of ODT VDDQ VDDQ VDDQ sw1 sw2 sw3 Rval1 Rval2 Rval3 DRAM Input Buffer Input Pin Rval1 Rval2 Rval3 sw1 sw2 sw3 VSSQ VSSQ VSSQ Switch sw1, sw2, or sw3 is enabled by the ODT pin. Selection between sw1, sw2, or sw3 is determined by "Rtt (nominal)" in EMR. Termination included on all DQs, DM, DQS, DQS, RDQS, and RDQS pins. REV 1.3 09/2009 18 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die ODT related timings MRS command to ODT update delay During normal operation the value of the effective termination resistance can be changed with an EMRS command. The update of the Rtt setting is done between tMOD, min and tMOD, max, and CKE must remain HIGH for the entire duration of tMOD window for proper operation. The timings are shown in the following timing diagram. EMRS CMD NOP NOP NOP NOP NOP CK, CK tIS CKE tMOD, max tAOFD Rtt tMOD, min Old setting Updating New setting EMRS command directed to EMR(1), which updates the information in EMR(1)[A6,A2], i.e. Rtt(Nominal) Setting in this diagram is the Register and I/O setting, not what is measured from outside. However, to prevent any impedance glitch on the channel, the following conditions must be met. - tAOFD must be met before issuing the EMRS command. - ODT must remain LOW for the entire duration of tMOD window, until tMOD ,max is met. Now the ODT is ready for normal operation with the new setting, and the ODT may be raised again to turned on the ODT. Following timing diagram shows the proper Rtt update procedure. ntire duration of tMOD window for proper operation. The timings are shown in the following timing diagram. EMRS CMD NOP NOP NOP NOP NOP CK, CK tIS CKE tAOND tMOD, max tAOFD Rtt Old setting New setting EMRS command directed to EMR(1), which updates the information in EMR(1)[A6,A2], i.e. Rtt(Nominal) Setting in this diagram is the Register and I/O setting, not what is measured from outside. REV 1.3 09/2009 19 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die ODT On/Off timings ODT timing for active/standby mode T-1 T-0 T-2 T-3 T-4 T-6 T-5 CK, CK tIS CKE tIS tIS ODT tAOND tAOFD(2. 5 tck) Internal Term Res. Rtt tAON, min tAOF, min tAON, max tAOF, max ODT Timing for Power-down mode T0 T1 T2 T3 T5 T4 T6 CK, CK CKE tIS ODT tIS tAOFPD,max tAOFPD,min DQ Rtt tAONPD,min tAONPD,max REV 1.3 09/2009 20 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Bank Activate Command The Bank Activate command is issued by holding CAS and WE high with CS and RAS low at the rising edge of the clock. The bank addresses BA0 ~ BA2 are used to select the desired bank. The row addresses A0 through A13 are used to determine which row to activate in the selected bank for x4 and x8 organised components. For x16 components row addresses A0 through A12 have to be applied. The Bank Activate command must be applied before any Read or Write operation can be executed. Immediately after the bank active command, the DDR2 SDRAM can accept a read or write command (with or without Auto-Precharge) on the following clock cycle. If a R/W command is issued to a bank that has not satisfied the tRCDmin specification, then additive latency must be programmed into the device to delay the R/W command which is internally issued to the device. The additive latency value must be chosen to assure tRCDmin is satisfied. Additive latencies of 0, 1, 2, 3, and 4 are supported. Once a bank has been activated it must be precharged before another Bank Activate command can be applied to the same bank. The bank active and precharge times are defined as tRAS and tRP, respectively. The minimum time interval between successive Bank Activate commands to the same bank is determined (tRC). The minimum time interval between Bank Active commands, to any other bank, is the Bank A to Bank B delay time (tRRD). In order to ensure that 8 bank devices do not exceed the instantaneous current supplying capability of 4 bank devices, certain restrictions on operation of the 8 bank devices must be observed. There are two rules. One for restricting the number of sequential ACTcommands that can be issued and another for allowing more time for RAS precharge for a Precharge All command. The rules are list as follow: * 8 bank device sequential Bank Activation Restriction: No more than 4 banks may be activated in a rolling tFAW window. Conveting to clocks is done by dividing tFAW by tCK and rounding up to next integer value. As an example of the rolling window, if (tFAW/tCK) rounds up to 10 clocks, and an activate command is issued in clock N, no more than three further activate commands may be issued in clock N+1 through N+9. *8 bank device Precharge All Allowance: tRP for a Precharge All command for an 8 Bank device will equal to tRP+tCK, where tRP is the value for a single bank pre-charge. Bank Activate Command Cycle: tRCD = 3, AL = 2, tRP = 3, tRRD = 2, tCCD = 2 T0 T1 T2 T3 T4 Tn Tn+1 Tn+2 Tn+3 CK, CK Internal RAS-CAS delay tRCDmin. Address Bank A Row Addr. Bank A Col. Addr. Bank B Row Addr. Bank B Col. Addr. Bank A Addr. NOP Bank B Addr. Bank A Row Addr. Bank A to Bank B delay tRRD. additive latency AL=2 RAS-RAS delay tRRD. Command Bank A Activate Posted CAS Read A Bank B Activate Read A Begins Posted CAS Read B Bank A Precharge tRC Row Cycle Time (Bank A) 09/2009 Bank B Precharge Bank A Activate tRP Row Precharge Time (Bank A) tRAS Row Active Time (Bank A) REV 1.3 NOP ACT 21 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Read and Write Commands and Access Modes After a bank has been activated, a read or write cycle can be executed. This is accomplished by setting RAS high, CS and CAS low at the clock's rising edge. WE must also be defined at this time to determine whether the access cycle is a read operation (WE high) or a write operation (WE low). The DDR2 SDRAM provides a fast column access operation. A single Read or Write Command will initiate a serial read or write operation on successive clock cycles. The boundary of the burst cycle is restricted to specific segments of the page length. A new burst access must not interrupt the previous 4 bit burst operation in case of BL = 4 setting. However, in case of BL=8 setting, two cases of interrupt by a new burst access are allowed, one reads interrupted by a read, the other writes interrupted by a write with 4 bit burst boundary respectively. The minimum CAS to CAS delay (tCCD) is a minimum of 2 clocks for read or write cycles. Posted CAS Posted CAS operation is supported to make command and data bus efficient for sustainable bandwidths in DDR2 SDRAM. In this operation, the DDR2 SDRAM allows a Read or Write command to be issued immediately after the RAS bank activate command (or any time during the RAS to CAS delay time, tRCD, period). The command is held for the time of the Additive Latency (AL) before it is issued inside the device. The Read Latency (RL) is the sum of AL and the CAS latency (CL). Therefore if a user chooses to issue a Read/Write command before the tRCDmin, then AL greater than 0 must be written into the EMR(1). The Write Latency (WL) is always defined as RL - 1 (Read Latency -1) where Read Latency is defined as the sum of Additive Latency plus CAS latency (RL=AL+CL). If a user chooses to issue a Read command after the tRCDmin period, the Read Latency is also defined as RL = AL + CL. Example of posted CAS operation: Read followed by a write to the same bank: AL = 2 and CL = 3, RL = (AL + CL) = 5, WL = (RL -1) = 4, BL = 4 -1 0 1 Activate Bank A Read Bank A 2 3 4 5 6 7 8 9 10 11 12 CK, CK CMD DQS, DQS Write Bank A AL = 2 WL = RL -1 = 4 CL = 3 >=tRCD RL = AL + CL = 5 DQ Dout0 Dout1 Dout2Dout3 Din0 Din1 Din2 Din3 PostCAS1 REV 1.3 09/2009 22 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Read followed by a write to the same bank: AL = 0, CL = 3, RL = (AL + CL) = 3, WL = (RL -1) = 2, BL = 4 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 CK, CK AL=0 CMD Read Bank A Activate Bank A >=tRCD Write Bank A CL=3 WL = RL - 1 = 2 DQS, DQS DQ RL = AL + CL = 3 Dout0 Dout1 Dout2 Dout3 Din0 Din1 Din2 Din3 PostCAS5 REV 1.3 09/2009 23 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Mode Operation Burst mode operation is used to provide a constant flow of data to memory locations (write cycle), or from memory locations (read cycle). The parameters that define how the burst mode will operate are burst sequence and burst length. The DDR2 SDRAM supports 4 bit and 8 bit burst modes only. For 8 bit burst mode, full interleave address ordering is supported, however, sequential address ordering is nibble based for ease of implementation. The burst type, either sequential or interleaved, is programmable and defined by the address bit 3 (A3) of the MRS. Seamless burst read or write operations are supported. Interruption of a burst read or write operation is prohibited, when burst length = 4 is programmed. For burst interruption of a read or write burst when burst length = 8 is used, see the "Burst Interruption " section of this datasheet. A Burst Stop command is not supported on DDR2 SDRAM devices. Burst Length and Sequence Burst Length Starting Address (A2 A1 A0) Sequential Addressing (decimal) Interleave Addressing (decimal) x 00 0, 1, 2, 3 0, 1, 2, 3 x 01 1, 2, 3, 0 1, 0, 3, 2 x 10 2, 3, 0, 1 2, 3, 0, 1 x 11 3, 0, 1, 2 3, 2, 1, 0 000 0, 1, 2, 3, 4, 5, 6, 7 0, 1, 2, 3, 4, 5, 6, 7 001 1, 2, 3, 0, 5, 6, 7, 4 1, 0, 3, 2, 5, 4, 7, 6 010 2, 3, 0, 1, 6, 7, 4, 5 2, 3, 0, 1, 6, 7, 4, 5 011 3, 0, 1, 2, 7, 4, 5, 6 3, 2, 1, 0, 7, 6, 5, 4 100 4, 5, 6, 7, 0, 1, 2, 3 4, 5, 6, 7, 0, 1, 2, 3 101 5, 6, 7, 4, 1, 2, 3, 0 5, 4, 7, 6, 1, 0, 3, 2 110 6, 7, 4, 5, 2, 3, 0, 1 6, 7, 4, 5, 2, 3, 0, 1 111 7, 4, 5, 6, 3, 0, 1, 2 7, 6, 5, 4, 3, 2, 1, 0 4 8 Note: 1) Page length is a function of I/O organization 256Mb X 4 organization (CA0-CA9, CA11); Page Size = 1kByte; Page Length = 2048 128Mb X 8 organization (CA0-CA9 ); Page Size = 1kByte; Page Length = 1024 64Mb X 16 organization (CA0-CA9); Page Size = 2kByte; Page Length = 1024 2) Order of burst access for sequential addressing is "nibble-based" and therefore different from SDR or DDR components REV 1.3 09/2009 24 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Read Command The Burst Read command is initiated by having CS and CAS low while holding RAS and WE high at the rising edge of the clock. The address inputs determine the starting column address for the burst. The delay from the start of the command until the data from the first cell appears on the outputs is equal to the value of the read latency (RL). The data strobe output (DQS) is driven low one clock cycle before valid data (DQ) is driven onto the data bus. The first bit of the burst is synchronized with the rising edge of the data strobe (DQS). Each subsequent data-out appears on the DQ pin in phase with the DQS signal in a source synchronous manner. The RL is equal to an additive latency (AL) plus CAS latency (CL). The CL is defined by the Mode Register Set (MRS). The AL is defined by the Extended Mode Register Set (EMR(1)) Basic Burst Read Timing t CH t CL t CK CLK CLK, CLK CLK t DQSCK t AC DQS DQS, DQS DQS t RPRE t RPST t LZ DQ Dout t DQSQmax t QH Dout t HZ Dout Dout t DQSQmax t QH DO-Read Examples: Burst Read Operation: RL = 5 (AL = 2, CL = 3, BL = 4) T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD Post CAS READ A NOP NOP NOP NOP NOP NOP NOP NOP <= tDQSCK DQS, DQS AL = 2 DQ CL = 3 RL = 5 Dout A0 Dout A1 Dout A2 Dout A3 BRead523 REV 1.3 09/2009 25 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Read Operation: RL = 3 (AL = 0, CL = 3, BL = 8) T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD READ A NOP NOP NOP NOP NOP NOP NOP NOP <= tDQSCK DQS, DQS CL = 3 RL = 3 DQ's Dout A0 Dout A1 Dout A2 Dout A3 Dout A4 Dout A5 Dout A6 Dout A7 BRead303 Burst Read followed by Burst Write : RL = 5, WL = (RL-1) = 4, BL = 4 T0 T1 Tn-1 Tn Tn+1 Tn+2 Tn+3 Tn+4 Tn+5 CK, CK CMD Posted CAS READ A NOP NOP Posted CAS WRITE A NOP NOP NOP NOP NOP tRTW(Read to Write turn around time) DQS, DQS WL = RL - 1 = 4 RL = 5 DQ Dout A0 Dout A1 Dout A2 Dout A3 Din A0 Din A1 Din A2 Din A3 BRBW514 The minimum time from the burst read command to the burst write command is defined by a read-to-write-turnaround time(tRTW), which is 4 clocks in case of BL=4 operation, 6 clocks in case of BL=8 operation. REV 1.3 09/2009 26 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Seamless Burst Read Operation : RL = 5, AL = 2, CL = 3, BL = 4 T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD Post CAS READ A NOP Post CAS READ B NOP NOP NOP NOP NOP NOP DQS, DQS AL = 2 DQ CL = 3 RL = 5 Dout A0 Dout A1 Dout A2 Dout A3 Dout B0 Dout B1 Dout B2 Dout B3 SBR523 The seamless burst read operation is supported by enabling a read command at every other clocks for BL=4 operation, and every 4 clock for BL=8 operation. This operation is allowed regardless of same or different banks as long as the banks are activated. REV 1.3 09/2009 27 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Write Command The Burst Write command is initiated by having CS, CAS and WE low while holding RAS high at the rising edge of the clock. The address inputs determine the starting column address. Write latency (WL) is defined by a read latency (RL) minus one and is equal to (AL + CL -1). A data strobe signal (DQS) has to be driven low (preamble) a time tWPRE prior to the WL. The first data bit of the burst cycle must be applied to the DQ pins at the first rising edge of the DQS following the preamble. The tDQSS specification must be satisfied for write cycles. The subsequent burst bit data are issued on successive edges of the DQS until the burst length is completed, which is 4 or 8 bit burst. When the burst has finished, any additional data supplied to the DQ pins will be ignored. The DQ signal is ignored after the burst write operation is complete. The time from the completion of the burst write to bank precharge is named "write recovery time" (WR) . DDR2 SDRAM pin timings are specified for either single ended mode or differential mode depending on the setting of the EMRS "Enable DQS" mode bit; timing advantages of differential mode are realized in system design. The method by which the DDR2 SDRAM pin timing are measured is mode dependent. Basic Burst Write Timing t DQSH t DQSL DQS DQS, DQS DQS t WPST t WPRE Din Din Din Din t DS t DH Example:. Burst Write Operation : RL = 5 (AL = 2, CL = 3), WL = 4, BL = 4 T0 T1 T2 T3 T4 T5 T6 T7 T9 CK, CK CMD Post CAS WRITE A NOP NOP NOP NOP NOP <= tDQSS DQS, DQS REV 1.3 09/2009 NOP Precharge Completion of the Burst Write tWR WL = RL-1 = 4 DQ NOP DIN A0 DIN A1 DIN A2 DIN A3 28 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Write Operation : RL = 3 (AL = 0, CL = 3), WL = 2, BL = 4 T0 T1 T2 T3 T4 T5 T6 T7 T9 CK, CK CMD Post CAS WRITE A NOP NOP NOP NOP NOP Bank A Activate Completion of the Burst Write <= tDQSS DQS, DQS tRP tWR WL = RL-1 = 2 DQ Precharge NOP DIN A0 DIN A1 DIN A2 DIN A3 BW322 Burst Write followed by Burst Read : RL = 5 (AL = 2, CL = 3), WL = 4, tWTR = 2, BL = 4 T0 T1 T2 T3 T4 T5 T6 T7 T9 T8 CK, CK Write to Read = (CL - 1)+ BL/2 +tWTR(2) = 6 CMD NOP NOP NOP NOP Post CAS READ A NOP NOP NOP NOP DQS, DQS AL=2 tWTR WL = RL - 1 = 4 DQ DIN A0 DIN A1 DIN A2 DIN A3 CL=3 RL=5 BWBR The minimum number of clocks from the burst write command to the burst read command is (CL - 1) +BL/2 + tWTR where tWTR is the write-to-read turn-around time tWTR expressed in clock cycles. The tWTR is not a write recovery time (tWR) but the time required to transfer 4 bit write data from the input buffer into sense amplifiers in the array. REV 1.3 09/2009 29 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Seamless Burst Write Operation : RL = 5, WL = 4, BL = 4 T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD Post CAS WRITE A NOP Post CAS WRITE B NOP NOP NOP NOP NOP NOP DQS, DQS WL = RL - 1 = 4 DQ DIN A0 DIN A1 DIN A2 DIN A3 DIN B0 DIN B1 DIN B2 DIN B3 SBR The seamless burst write operation is supported by enabling a write command every BL / 2 number of clocks. This operation is allowed regardless of same or different banks as long as the banks are activated. REV 1.3 09/2009 30 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Write Data Mask One write data mask input (DM) pin for each 8 data bits (DQ) will be supported on DDR2 SDRAMs, consistent with the implementation on DDR SDRAMs. It has identical timings on write operations as the data bits, and though used in a uni-directional manner, is internally loaded identically to data bits to insure matched system timing. DM of x4 and x16 bit organization is not used during read cycles. However, DM of x8 bit organization can be used as RDQS during read cycles by EMR(1) setting. Write Data Mask Timing t DQSH t DQSL DQS DQS, DQS DQS t WPST t WPRE DQ Din Din t DS Din Din t DH DM don't care Burst Write Operation with Data Mask : RL = 3 (AL = 0, CL = 3), WL = 2, tWR = 3 , BL = 4 T0 T1 T2 T3 T4 T5 T6 T7 T9 CK, CK CMD WRITE A NOP NOP NOP NOP NOP NOP Precharge Bank A Activate <= tDQSS DQS, DQS WL = RL-1 = 2 DQ tWR tRP DIN A0 DIN A1 DIN A2 DIN A3 DM DM REV 1.3 09/2009 31 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Interruption Interruption of a read or write burst is prohibited for burst length of 4 and only allowed for burst length of 8 under the following conditions: 1. A Read Burst of 8 can only be interrupted by another Read command. Read burst interruption by a Write or Precharge Command is prohibited. 2. A Write Burst of 8 can only be interrupted by another Write command. Write burst interruption by a Read or Precharge Command is prohibited. 3. Read burst interrupt must occur exactly two clocks after the previous Read command. Any other Read burst interrupt timings are prohibited. 4. Write burst interrupt must occur exactly two clocks after the previous Write command. Any other Read burst interrupt timings are prohibited. 5. Read or Write burst interruption is allowed to any bank inside the DDR2 SDRAM. 6. Read or Write burst with Auto-Precharge enabled is not allowed to be interrupted. 7. Read burst interruption is allowed by a Read with Auto-Precharge command. 8. Write burst interruption is allowed by a Write with Auto-Precharge command. 9. All command timings are referenced to burst length set in the mode register. They are not referenced to the actual burst. For example, Minimum Read to Precharge timing is AL + BL/2 where BL is the burst length set in the mode register and not the actual burst (which is shorter because of interrupt). Minimum Write to Precharge timing is WL + BL/ 2 + tWR, where tWR starts with the rising clock after the un-interrupted burst end and not form the end of the actual burst end. Examples: Read Burst Interrupt Timing Example : (CL = 3, AL = 0, RL = 3, BL = 8) T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD READ A NOP READ B NOP NOP NOP NOP NOP NOP DQS, DQS DQ Dout A0 Dout A1 Dout A2 Dout A3 Dout B0 Dout B1 Dout B2 Dout B3 Dout B4 Dout B5 Dout B6 Dout B7 RBI REV 1.3 09/2009 32 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Write Burst Interrupt Timing Example : ( CL = 3, AL = 0, WL = 2, BL = 8) T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD NOP WRITE A NOP NOP NOP WRITE B NOP NOP NOP DQS, DQS DQ Din A0 Din A1 Din A2 Din A3 Din B0 Din B1 Din B2 Din B3 Dout B4 Din B5 Din B6 Din B7 WBI REV 1.3 09/2009 33 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Precharge Command The Precharge Command is used to precharge or close a bank that has been activated. The Precharge Command is triggered when CS, RAS and WE are low and CAS is high at the rising edge of the clock. The Pre-charge Command can be used to precharge each bank independently or all banks simultaneously. Three address bits A10, BA0, BA1, and BA2 are used to define which bank to precharge when the command is issued. Bank Selection for Precharge by Address Bit A10 BA2 BA1 BA0 Precharge Bank(s) LOW LOW LOW LOW Bank 0 only LOW LOW LOW HIGH Bank 1 only LOW LOW HIGH LOW Bank 2 only LOW LOW HIGH HIGH Bank 3 only LOW HIGH LOW LOW Bank 4 only LOW HIGH LOW HIGH Bank 5 only LOW HIGH HIGH LOW Bank 6 only LOW HIGH HIGH HIGH Bank 7 only HIGH Don't Care Don't Care Don't Care all banks Burst Read Operation Followed by a Precharge Minimum Read to Precharge command spacing to the same bank = AL + BL/2 + max(RTP,2) - 2 clocks. For the earliest possible precharge, the Precharge command may be issued on the rising edge which is "Additive Latency (AL) + BL/2 clocks" after a Read Command, as long as the minimum tRAS timing is satisfied. The minimum Read to Precharge spacing has also to satisfy a minimum analog time from the rising clock edge that initiates the last 4-bit prefetch of a Read to Precharge command. This time is call tRTP (Read to Precharge). For BL=4 this is the time from the actual read ( AL after the Read command) to Precharge command. For BL=8 this is the time from AL + 2 clocks after the Read to the Precharge command. REV 1.3 09/2009 34 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Examples: Burst Read Operation Followed by Precharge: RL = 4 (AL = 1, CL = 3), BL = 4, tRTP <= 2 clocks T0 T1 T2 T3 NOP NOP Precharge T4 T5 T6 T7 T8 CK, CK CMD Post CAS READ A NOP NOP NOP AL + BL/2 clks Bank A Activate NOP >=tRP DQS, DQS AL = 1 CL = 3 RL = 4 DQ Dout A0 >=tRAS Dout A1 Dout A2 Dout A3 CL = 3 >=tRC >=tRTP Burst Read Operation Followed by Precharge: RL = 4 (AL = 1, CL = 3), BL = 8, tRTP <= 2 clocks T0 T1 T2 T3 T4 T5 T6 Precharge NOP T7 T8 CK, CK CMD Post CAS READ A NOP NOP NOP NOP NOP NOP AL + BL/2 clks DQS, DQS AL = 1 CL = 3 RL = 4 DQ Dout A0 >=tRAS Dout A1 Dout A2 Dout A3 Dout A4 Dout A5 Dout A6 Dout A7 CL = 3 >=tRC >=tRTP first 4-bit prefetch REV 1.3 09/2009 BR-P413(8) second 4-bit prefetch 35 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Read Operation Followed by Precharge: RL = 5 (AL = 2, CL = 3), BL = 4, tRTP <= 2 clocks T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD Post CAS READ A NOP NOP NOP NOP Precharge AL + BL/2 clks NOP Bank A Activate NOP >=tRP DQS, DQS CL = 3 AL = 2 RL = 5 DQ Dout A0 >=tRAS Dout A1 Dout A2 Dout A3 CL = 3 >=tRC >=tRTP BR-P523 Burst Read Operation Followed by Precharge: RL = 6, (AL = 2, CL = 4), BL = 4, tRTP <= 2 clocks T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD Post CAS READ A NOP NOP NOP Precharge A AL + BL/2 clocks NOP NOP Bank A Activate NOP >=tRP DQS, DQS AL = 2 CL = 4 DQ RL = 6 Dout A0 >=tRAS Dout A1 Dout A2 Dout A3 CL = 4 >=tRC >=tRTP REV 1.3 09/2009 BR-P624 36 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Read Operation Followed by Precharge: RL = 4, (AL = 0, CL = 4), BL = 8, tRTP > 2 clocks T0 T1 T2 T3 T4 T5 T6 NOP NOP Precharge T7 T8 CK, CK CMD READ A NOP NOP NOP NOP AL + BL/2 clks + 1 Bank A Activate >=tRP DQS, DQS CL = 4 RL = 4 DQ Dout A0 Dout A1 Dout A2 Dout A3 Dout A4 Dout A5 Dout A6 Dout A7 >=tRAS >=tRTP first 4-bit prefetch REV 1.3 09/2009 BR-P404(8) second 4-bit prefetch 37 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Write followed by Precharge Minimum Write to Precharge command spacing to the same bank = WL + BL/2 + tWR. For write cycles, a delay must be satisfied from the completion of the last burst write cycle until the Precharge command can be issued. This delay is known as a write recovery time (tWR) referenced from the completion of the burst write to the Precharge command. No Precharge command should be issued prior to the tWR delay, as DDR2 SDRAM does not support any burst interrupt by a Precharge command. tWR is an analog timing parameter (see the AC table in this datasheet) and is not the programmed value for tWR in the MRS. Examples: Burst Write followed by Precharge : WL = (RL - 1) = 3, BL = 4, tWR = 3 T 0 T 1 T 2 T 3 T 4 T 5 T 6 T 7 T 8 CK, CK CMD Post CAS WRITE A NOP NOP NOP NOP NOP NOP NOP Precharge A Completion of the Burst Write DQS, DQS >=tWR WL = 3 DIN A0 DQ DIN A1 DIN A2 DIN A3 BW-P3 Burst Write followed by Precharge : WL = (RL - 1) = 4, BL = 4, tWR = 3 T0 T1 T2 T3 T4 T5 T6 T7 T9 CK, CK CMD Post CAS WRITE A NOP NOP NOP NOP NOP NOP Precharge A Completion of the Burst Write DQS, DQS tWR WL = 4 DQ NOP DIN A0 DIN A1 DIN A2 DIN A3 BW-P4 REV 1.3 09/2009 38 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Auto-Precharge Operation Before a new row in an active bank can be opened, the active bank must be precharged using either the Pre-charge Command or the Auto-Precharge function. When a Read or a Write Command is given to the DDR2 SDRAM, the CAS timing accepts one extra address, column address A10, to allow the active bank to auto-matically begin precharge at the earliest possible moment during the burst read or write cycle. If A10 is low when the Read or Write Command is issued, then normal Read or Write burst operation is executed and the bank remains active at the completion of the burst sequence. If A10 is high when the Read or Write Com-mand is issued, then the Auto-Precharge function is enabled. During Auto-Precharge, a Read Command will execute as normal with the exception that the active bank will begin to precharge internally on the rising edge which is CAS Latency (CL) clock cycles before the end of the read burst. Auto-Precharge is also implemented for Write Commands.The precharge operation engaged by the Auto-Precharge command will not begin until the last data of the write burst sequence is properly stored in the memory array. This feature allows the precharge operation to be partially or completely hidden during burst read cycles (dependent upon CAS Latency) thus improving system performance for random data access. The RAS lockout circuit internally delays thepprecharge operation until the array restore operation has been completed so that the Auto-Precharge command may be issued with any read or write command. Burst Read with Auto-Precharge If A10 is high when a Read Command is issued, the Read with Auto-Precharge function is engaged. The DDR2 SDRAM starts an Auto-Precharge operation on the rising edge which is (AL + BL/2) cycles later from the Read with AP command if tRAS(min) and tRTP are satisfied. If tRAS(min) is not satisfied at the edge, the start point of Auto-Precharge operation will be delayed until tRAS(min) is satisfied. If tRTP(min) is not satisfied at the edge, the start point of Auto-Precharge operation will be delayed until tRTP(min) is satisfied. In case the internal precharge is pushed out by tRTP, tRP starts at the point where the internal precharge happens (not at the next rising clock edge after this event). So for BL = 4 the minimum time from Read with Auto-Precharge to the next Activate command becomes AL + tRTP + tRP. For BL = 8 the time from Read with Auto-Precharge to the next Activate command is AL + 2 + tRTP + tRP. Note that both parameters tRTP and tRP have to be rounded up to the next integer value. In any event internal precharge does not start earlier than two clocks after the last 4-bit prefetch. A new bank active (command) may be issued to the same bank if the following two conditions are satisfied simultaneously: (1) The RAS precharge time (tRP) has been satisfied from the clock at which the Auto-Precharge begins. (2) The RAS cycle time (tRC) from the previous bank activation has been satisfied. REV 1.3 09/2009 39 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Examples: Burst Read with Auto-Precharge followed by an activation to the Same Bank (tRC Limit) RL = 5 (AL = 2, CL = 3), BL = 4, tRTP <= 2 clocks T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD Posted CAS READ w/AP NOP NOP NOP NOP NOP NOP NOP Bank Activate A10 ="high" AL + BL/2 Auto-Precharge Begins DQS, DQS AL = 2 CL = 3 tRP RL = 5 DQ Dout A0 Dout A1 Dout A2 Dout A3 tRAS tRCmin. BR-AP5231 Burst Read with Auto-Precharge followed by an Activation to the Same Bank (tRAS Limit): RL = 5 ( AL = 2, CL = 3), BL = 4, tRTP <= 2 clocks T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD Posted CAS READ w/AP NOP NOP NOP NOP NOP Bank Activate NOP NOP A10 ="high" DQS, DQS tRAS(min) AL = 2 Auto-Precharge Begins CL = 3 tRP RL = 5 DQ Dout A0 Dout A1 Dout A2 Dout A3 tRC BR-AP5232 REV 1.3 09/2009 40 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Read with Auto-Precharge followed by an Activation to the Same Bank: RL = 4 ( AL = 1, CL = 3), BL = 8, tRTP <= 2 clocks T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD Posted CAS READ w/AP NOP NOP NOP A10 ="high" NOP NOP NOP AL + BL/2 NOP Bank Activate tRP Auto-Precharge Begins DQS, DQS AL = 1 CL = 3 RL = 4 DQ Dout A0 Dout A1 Dout A2 Dout A3 Dout A4 Dout A5 Dout A6 Dout A7 >= tRTP BR-AP413(8)2 second 4-bit prefetch first 4-bit prefetch Burst Read with Auto-Precharge followed by an Activation to the Same Bank: RL = 4 ( AL = 1, CL = 3), BL = 4, tRTP > 2 clocks T0 T1 T2 T3 T4 T5 T6 T7 T8 CK, CK CMD Posted CAS READ w/AP A10 ="high" NOP NOP NOP NOP NOP NOP Bank Activate NOP AL + tRTP + tRP Auto-Precharge Begins DQS, DQS AL = 1 CL = 3 RL = 4 DQ Dout A0 Dout A1 Dout A2 Dout A3 tRP tRTP BR-AP4133 first 4-bit prefetch REV 1.3 09/2009 41 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Write with Auto-Precharge If A10 is high when a Write Command is issued, the Write with Auto-Precharge function is engaged. The DDR2 SDRAM automatically begins precharge operation after the completion of the write burst plus the write recovery time delay (WR), programmed in the MRS register, as long as tRAS is satisfied. The bank undergoing Auto-Precharge from the completion of the write burst may be reactivated if the following two conditions are satisfied. (1) The last data-in to bank activate delay time (tDAL = WR + tRP) has been satisfied. (2) The RAS cycle time (tRC) from the previous bank activation has been satisfied. Examples: Burst Write with Auto-Precharge (tRC Limit) : WL = 2, tDAL = 6 (WR = 3, tRP = 3) , BL = 4 T0 T1 T2 T3 T4 T5 T6 T7 CK, CK CMD WRITE w/AP NOP A10 ="high" NOP NOP NOP NOP NOP Completion of the Burst Write NOP Bank A Activate Auto-Precharge Begins DQS, DQS WR WL = RL-1 = 2 tRP tDAL DQ DIN A0 DIN A1 DIN A2 DIN A3 tRCmin. >=tRASmin. BW-AP223 REV 1.3 09/2009 42 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Burst Write with Auto-Precharge (tWR + tRP Limit) : WL = 4, tDAL = 6 (tWR = 3, tRP = 3), BL = 4 T 3 T 0 T 4 T 5 T 6 NOP NOP T 7 T 8 T 9 T12 CK, CK CMD Posted CAS WRITE w/AP NOP A10 ="high" NOP NOP NOP NOP Bank A Activate Completion of the Burst Write Auto-Precharge Begins DQS, DQS DIN A0 DQ tRP tWR WL = RL-1 = 4 DIN A1 DIN A2 tDAL DIN A3 >=tRC >=tRAS BW-AP423 Precharge & auto precharge clarification To Command Minimum Delay between "From command" to "to command" Units Note Precharge (to same Bank as Read) AL + BL/2 + max(RTP,2) - 2 tCK 1,2 Precharge All AL + BL/2 + max(RTP,2) - 2 tCK 1,2 Precharge ( to same Bank as Read wAP) AL + BL/2 + max(RTP,2) - 2 tCK 1,2 Precharge Al AL + BL/2 + max(RTP,2) - 2 tCK 1,2 Precharge (to same Bank as Write) WL + BL/2 + tWR tCK 2 Precharge Al WL + BL/2 + tWR tCK 2 Precharge (to same bank as Write w/AP) WL + BL/2 + WR tCK 2 Precharge Al WL + BL/2 + WR tCK 2 Precharge (to same bank as Precharge) 1 tCK 2 Precharge Al 1 tCK 2 Precharge 1 tCK 2 Precharge Al 1 tCK 2 From Command Read Read w/AP Write Write w/AP Precharge Precharge All Note: 1) RTP[cycles] = RU{tRTP(ns)/tCK(ns)}, where RI stands for round up. 2) For a given bank, the precharge period should be counted from the latest precharge command, either one bank precharge or precharge all, issued to that bank. The precharge period is satisfied after tRP or tRPa depending on the latest precharge command issued to that bank. REV 1.3 09/2009 43 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Refresh SDRAMs require a refresh of all rows in any rolling 64 ms interval. Each refresh is generated in one of two ways : by an explicit Auto-Refresh command, or by an internally timed event in Self-Refresh mode. Dividing the number of device rows into the rolling 64 ms interval defined the average refresh interval tREFI, which is a guideline to controlles for distributed refresh timing. For example, a 512Mbit DDR2 SDRAM has 8192 rows resulting in a tREFI of 7,8 s. Auto-Refresh Command Auto-Refresh is used during normal operation of the DDR2 SDRAMs. This command is nonpersistent, so it must be issued each time a refresh is required. The refresh addressing is generated by the internal refresh controller. This makes the address bits "Don't Care" during an Auto-Refresh command. The DDR2 SDRAM requires Auto-Refresh cycles at an average periodic interval of tREFI (maximum). When CS, RAS and CAS are held low and WE high at the rising edge of the clock, the chip enters the Auto-Refresh mode. All banks of the SDRAM must be precharged and idle for a minimum of the precharge time (tRP) before the Auto-Refresh Command can be applied. An internal address counter supplies the addresses during the refresh cycle. No control of the external address bus is required once this cycle has started. When the refresh cycle has completed, all banks of the SDRAM will be in the precharged (idle) state. A delay between the AutoRefresh Command and the next Activate Command or subsequent Auto-Refresh Command must be greater than or equal to the Auto-Refresh cycle time (tRFC). To allow for improved efficiency in scheduling and switching between tasks, some flexibility in the absolute refresh interval is provided. A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM, meaning that the maximum absolute interval between any Auto-Refresh command and the next Auto-Refresh command is 9 * tREFI. T0 T1 T2 T3 CK, CK "high" CKE CMD Precharge NOP > = t RFC > = t RFC > = t RP NOP AUTO REFRESH NOP AUTO REFRESH NOP NOP ANY AR REV 1.3 09/2009 44 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Self-Refresh Command The Self-Refresh command can be used to retain data, even if the rest of the system is powered down. When in the Self-Refresh mode, the DDR2 SDRAM retains data without external clocking. The DDR2 SDRAM device has a built-in timer to accommodate Self-Refresh operation. The Self-Refresh Command is defined by having CS, RAS, CAS and CKE held low with WE high at the rising edge of the clock. ODT must be turned off before issuing Self Refresh command, by either driving ODT pin low or using EMR(1) command. Once the command is registered, CKE must be held low to keep the device in Self-Refresh mode. When the DDR2 SDRAM has entered Self-Refresh mode all of the external control signals, except CKE, are disabled. The clock is internally disabled during Self-Refresh Operation to save power. The user may change the external clock frequency or halt the external clock one clock after Self-Refresh entry is registered, however, the clock must be restarted and stable before the device can exit Self-Refresh operation. Once Self-Refresh Exit command is registered, a delay equal or longer than the tXSNR or tXSRD must be satisfied before a valid command can be issued to the device. CKE must remain high for the entire Self-Refresh exit period (tXSNR or tXSRD) for proper operation. NOP or DESELECT commands must be registered on each positive clock edge during the Self-Refresh exit interval. Since the ODT function is not supported during Self-Refresh operation, ODT has to be turned off tAOFD before entering Self-Refresh Mode and can be turned on again when the tXSRD timing is satisfied. T0 T1 T2 T3 T4 T5 Tm Tn Tr CK/CK tRP* tis tis >=tXSRD CKE tis tAOFD >= tXSNR ODT CMD Self Refresh Entry NOP CK/CK may be halted Non-Read Command Read Command CK/CK must be stable * = Device must be in the "All banks idle" state to entering Self Refresh mode. ODT must be turned off prior to entering Self Refresh mode. tXSRD (>=200 tCK) has to be satisfied for a Read or a Read with Auto-Precharge command. tXSNR has to be satisfied for any command except a Read or a Read with Auto-Precharge command, where tXSNR is defined as tRFC + 10ns. The miminum CKE low time is defined by the tCKEmin. timing parameter. Since CKE is an SSTL input, VREF must be maintained during Self Refresh. REV 1.3 09/2009 45 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Power-Down Power-down is synchronously entered when CKE is registered low, along with NOP or Deselect command. CKE is not allowed to go low while mode register or extended mode register command time, or read or write operation is in progress. CKE is allowed to go low while any other operation such as row activation, Precharge, Auto-Precharge or Auto-Refresh is in progress, but power-down IDD specification will not be applied until finishing those operations. The DLL should be in a locked state when power-down is entered. Otherwise DLL should be reset after exiting power-down mode for proper read operation. If power-down occurs when all banks are precharged, this mode is referred to as Precharge Power-down; if power-down occurs when there is a row active in any bank, this mode is referred to as Active Power-down. For Active Power-down two different power saving modes can be selected within the MRS register, address bit A12. When A12 is set to "low" this mode is referred as "standard active power-down mode" and a fast power-down exit timing defined by the tXARD timing parameter can be used. When A12 is set to "high" this mode is referred as a power saving "low power active power-down mode". This mode takes longer to exit from the power-down mode and the tXARDS timing parameter has to be satisfied. Entering power-down deactivates the input and output buffers, excluding CK, CK, ODT and CKE. Also the DLL is disabled upon entering Precharge Power-down or slow exit active power-down, but the DLL is kept enabled during fast exit active powerdown. In power-down mode, CKE low and a stable clock signal must be maintained at the inputs of the DDR2 SDRAM, and all other input signals are "Don't Care". Power-down duration is limited by 9 times tREFI of the device. The power-down state is synchronously exited when CKE is registered high (along with a NOP or Deselect command). A valid, executable command can be applied with power-down exit latency, tXP, tXARD or tXARDS, after CKE goes high. Power-down exit latencies are defined in the AC spec table of this data sheet. Power-Down Entry Active Power-down mode can be entered after an activate command. Precharge Power-down mode can be entered after a precharge, Precharge-All or internal precharge command. It is also allowed to enter power-mode after an Auto-Refresh command or MRS / EMR(1) command when tMRD is satisfied. Active Power-down mode entry is prohibited as long as a Read Burst is in progress, meaning CKE should be kept high until the burst operation is finished. Therefore Active Power-Down mode entry after a Read or Read with Auto-Precharge command is allowed after RL + BL/2 is satisfied. Active Power-down mode entry is prohibited as long as a Write Burst and the internal write recovery is in progress. In case of a write command, active power-down mode entry is allowed when WL + BL/2 + tWTR is satisfied. In case of a write command with Auto-Precharge, Power-down mode entry is allowed after the internal precharge command has been executed, which is WL + BL/2 + WR starting from the write with Auto-Precharge command. In case the DDR2 SDRAM enters the Precharge Power-down mode. REV 1.3 09/2009 46 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Examples: Active Power-Down Mode Entry and Exit after an Activate Command T0 T1 T2 Tn Tn+1 Tn+2 CK, CK CMD NOP Activate NOP Valid Command NOP NOP NOP tIS CKE tIS tXARD or tXARDS *) Act.PD 0 Active Power-Down Exit Active Power-Down Entry Note: Active Power-Down mode exit timing tXARD ("fast exit") or tXARDS ("slow exit") depends on the programmed state in the MRS, address bit A12. Active Power-Down Mode Entry and Exit after a Read Burst: RL = 4 (AL = 1, CL =3), BL = 4 T0 T1 T2 T3 T4 T5 T6 T7 Tn T8 Tn+1 Tn+2 CK, CK CMD READ READ w/AP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP Valid Command tIS CKE RL + BL/2 tIS DQS, DQS AL = 1 DQ tXARD or tXARDS *) CL = 3 RL = 4 Dout A0 Dout A1 Dout A2 Dout A3 Active Power-Down Entry Active Power-Down Exit Act.PD 1 Note: Active Power-Down mode exit timing tXARD ("fast exit") or tXARDS ("slow exit") depends on the programmed state in the MRS, address bit A12. REV 1.3 09/2009 47 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Active Power-Down Mode Entry and Exit after a Write Burst: WL = 2, tWTR = 2, BL = 4 T0 T1 T2 T3 T4 T5 T6 Tn T7 Tn+1 Tn+2 CK, CK CMD WRITE NOP NOP NOP NOP NOP NOP NOP NOP NOP Valid Command NOP tIS CKE WL + BL/2 + tWTR tIS DQS, DQS WL = RL - 1 = 2 tWTR DIN A0 DQ DIN A1 DIN A2 tXARD or tXARDS *) DIN A3 Active Power-Down Entry Active Power-Down Exit Act.PD 2 Note: Active Power-Down mode exit timing tXARD ("fast exit") or tXARDS ("slow exit") depends on the programmed state in the MRS, address bit A12. Precharge Power Down Mode Entry and Exit T0 T1 T2 T3 Tn Tn+1 Tn+2 CK, CK CMD Precharge *) NOP NOP NOP NOP NOP NOP Valid Command NOP tIS CKE tIS tXP tRP Precharge Power-Down Entry Precharge Power-Down Exit *) "Precharge" may be an external command or an internal precharge following Write with AP. REV 1.3 09/2009 PrePD 48 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die No Operation Command The No Operation Command should be used in cases when the SDRAM is in a idle or a wait state. The purpose of the No Operation Command is to prevent the SDRAM from registering any unwanted commands between operations. A No Operation Command is registered when CS is low with RAS, CAS, and WE held high at the rising edge of the clock. A No Operation Command will not terminate a previous operation that is still executing, such as a burst read or write cycle. Deselect Command The Deselect Command performs the same function as a No Operation Command. Deselect Command occurs when CS is brought high, the RAS, CAS, and WE signals become don't care. Input Clock Frequency Change During operation the DRAM input clock frequency can be changed under the following conditions: a) During Self-Refresh operation b) DRAM is in Precharge Power-down mode and ODT is completely turned off. The DDR2-SDRAM has to be in Precharged Power-down mode and idle. ODT must be allready turned off and CKE must be at a logic "low" state. After a minimum of two clock cycles after tRP and tAOFD have been satisfied the input clock frequency can be changed. A stable new clock frequency has to be provided, before CKE can be changed to a "high" logic level again. After tXP has been satisfied a DLL RESET command via EMR(1) has to be issued. During the following DLL re-lock period of 200 clock cycles, ODT must remain off. After the DLL-re-lock period the DRAM is ready to operate with the new clock frequency. Example: Input frequency change during Precharge Power-Down mode T0 T1 T2 T3 T4 Tx Tx+1 Ty Ty+1 Ty+2 Tz Ty+3 CK, CK NOP NOP NOP NOP NOP NOP NOP NOP tRP tAOFD NOP tXP Minimum 2 clocks required before changing the frequency Frequency Change occurs here Stable new clock before power-down exit DLL RESET NOP Valid Command 200 clocks ODT is off during DLL RESET Frequ.Ch. REV 1.3 09/2009 49 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Asynchronous CKE Low Event DRAM requires CKE to be maintained "high" for all valid operations as defined in this data sheet. If CKE asynchronously drops "low" during any valid operation DRAM is not guaranteed to preserve the contents of the memory array. If this event occurs, the memory controller must satisfy a time delay ( tdelay ) before turning off the clocks. Stable clocks must exist at the input of DRAM before CKE is raised "high" again. The DRAM must be fully re-initialized as described the the initialization sequence (section 2.2.1, step 4 thru 13). DRAM is ready for normal operation after the initialization sequence. See AC timing parametric table for tdelay specification. Asynchronous CKE Low Event stable clocks CK, CK tdelay CKE CKE drops low due to an asynchronous reset event REV 1.3 09/2009 Clocks can be turned off after this point 50 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Truth Table Command Truth Table CKE BA0 A13-A11 A10 BA2 Function Previous Cycle Current Cycle CS (Extended) Mode Register Set H H L L L L BA Auto-Refresh H H L L L H X X X X 1 Self-Refresh Entry H L L L L H X X X X 1,8 Self-Refresh Exit L H H X X X X X X X 1,7,8 Single Bank Precharge H H L L H L BA X L X 1,2 Precharge all Banks H H L L H L X X H X 1 Bank Activate H H L L H H BA Write H H L H L L BA Column L Column 1,2,3 Write with Auto-Precharge H H L H L L BA Column H Column 1,2,3 Read H H L H L H BA Column L Column 1,2,3 Read with Auto-Precharge H H L H L H BA Column H Column 1,2,3 No Operation H X L H H H X X X X 1 Device Deselect H X H X X X X X X X 1 Power Down Entry H X X X H L X X X X 1,4 L H H H H X X X X X X X 1,4 L H H H Power Down Exit L RAS CAS WE H A9 - A0 OP Code Notes 1, 2 Row Address 1,2 1. All DDR2 SDRAM commands are defined by states of CS, WE, RAS, CAS, and CKE at the rising edge of the clock. 2. Bank addresses (BAx) determine which bank is to be operated upon. For (E)MRS BxA selects an (Extended) Mode Register. 3. Burst reads or writes at BL = 4 cannot be terminated. See sections "Reads interrupted by a Read" and "Writes interrupted by a Write" insection for details. 4. The Power Down Mode does not perform any refresh operations. The duration of Power Down is therefore limited by the refresh requirements outlined . 5. The state of ODT does not affect the states decribed in this table. The ODT function is not available during Self Refresh. 6. "X" means "H or L (but a defined logic level)". 7. Self refresh exit is asynchronous. 8. Vref must be maintained during Self Refresh operation. REV 1.3 09/2009 51 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Clock Enable (CKE) Truth Table for Synchronous Transistions CKE Current State2 Command (N) 3 Previous Cycle 1 (N-1) Current Cycle 1 (N) RAS, CAS, WE, CS L L L Action (N) 3 Notes X Maintain Power-Down 11, 13, 15 H DESELECT or NOP Power-Down Exit 4, 8, 11, 13 L L X Maintain Self Refresh 11, 15, 16 L H DESELECT or NOP Self Refresh Exit 4, 5, 9, 16 H L DESELECT or NOP Active Power-Down Entry 4,8,10,11,13 H L DESELECT or NOP Precharge Power-Down Entry 4,8,10,11,13 AUTOREFRESH Self Refresh Entry 6, 9, 11,13 Power-Down Self Refresh Bank(s) Active All Banks Idle Any State other than listed above 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. H L H H Refer to the Command Truth Table 7 CKE (N) is the logic state of CKE at clock edge N; CKE (N-1) was the state of CKE at the previous clock edge. Current state is the state of the DDR2 SDRAM immediately prior to clock edge N. Command (N) is the command registered at clock edge N, and Action (N) is a result of Command (N). All states and sequences not shown are illegal or reserved unless explicitely described elsewhere in this document. On Self Refresh Exit DESELECT or NOP commands must be issued on every clock edge occuring during the tXSNR period. Read commands may be issued only after tXSRD (200 clocks) is satisfied. Self Refresh mode can only be entered from the All Banks Idle state. Must be a legal command as defined in the Command Truth Table. Valid commands for Power-Down Entry and Exit are NOP and DESELECT only. Valid commands for Self Refresh Exit are NOP and DESELCT only. Power-Down and Self Refresh can not be entered while Read or Write operations, (Extended) mode Register operations, Precharge or Refresh operations are in progress. See section 2.8 "Power Down" and section 2.7.2 "Self Refresh Command" for a detailed list of restrictions. Minimum CKE high time is 3 clocks, minimum CKE low time is 3 clocks. The state of ODT does not affect the states described in this table. The ODT function is not available during Self Refresh. The Power-Down Mode does not perform any refresh operations. The duration of Power-Down Mode is therefor limited by the refresh requirements. CKE must be maintained high while the device is in OCD calibration mode. "X" means "don't care (including floating around VREF)" in Self Refresh and Power Down. However ODT must be driven high or low in Power Down if the ODT function is enabled (Bit A2 or A6 set to "1" in EMR(1)). Vref must be maintained during Self Refresh operation. Data Mask (DM) Truth Table Name (Function) DM DQs Notes Write Enable L Valid 1 Write Inhibit H X 1 1. Used to mask write data; provided coincident with the corresponding data. REV 1.3 09/2009 52 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Operating Conditions Absolute Maximum Ratings Symbol Rating Units Notes Voltage on VDD pin relative to VSS -1.0 to + 2.3 V 1,3 VDDQ Voltage on VDDQ pin relative to VSS -0.5 to + 2.3 V 1,3 VDDL Voltage on VDDL pin relative to VSS -0.5 to + 2.3 V 1,3 Voltage on any pin relative to VSS -0.5 to + 2.3 V 1 Storage Temperature -55 to + 100 oC 1, 2 VDD VIN, VOUT TSTG Parameter 1. Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Storage Temperature is the case surface temperature on the center/top side of the DRAM. 3. When VDD, VDDQ, and VDDL are less than 500mV, Vref may be equal to or less than 300mV. DRAM Component Operating Temperature Range Symbol TOPER Parameter Operating Temperature Rating Units Notes 0 to 85 oC 1, 2 Note: 1. Operating temperature is the case surface temperature on the center/top side of the DRAM. 2. The operation temperature range are the temperature where all DRAM specification will be supported. Outside of this temperature range, even if it is still within the limit of stress condition, some deviation on portion of operation specification may be required. During operation, the DRAM case temperature must be maintained between 0-85 degree C under all other specification parameter. However, in some applications, it is desirable to operate the DRAM up to 95 degree C case temperature. Therefore, two spec may exist. Supporting 0-85C with full JEDEC AC & DC spec. This is the minimum requirements for all operating temperature options. This is an optional feature and not required. Supporting 0-85C and being able to extend to 95C with doubling auto-refresh command in frequency to a 32ms period (tRFI=3.9us) Currently the period Self-Refresh interval is hard coded within the DRAM to a vendor specific value. There is a migration plan to support higher temperature Self-Refresh entry via the control of EMR(2) bit A7. REV 1.3 09/2009 53 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die AC & DC Operating Conditions DC Operating Conditions Recommended DC Operating Conditions Rating Symbol Parameter Units Notes 1.6275 V 1 1.5 1.6275 V 5 1.425 1.5 1.6275 V 1,5 Input Reference Voltage 0.49 * VDDQ 0.5 * VDDQ 0.51 * VDDQ V 2, 3 Termination Voltage VREF - 0.04 VREF VREF + 0.04 V 4 Min. Typ. Max. Supply Voltage 1.425 1.5 VDDDL Supply Voltage for DLL 1.425 VDDQ Supply Voltage for Output VREF VDD VTT 1. VDDQ tracks with VDD, VDDDL tracks with VDD. AC parameters are measured with VDD, VDDQ and VDDDL tied together. 2. The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically the value of VREF is expected to be about 0.5 x VDDQ of the transmitting device and VREF is expected to track variations in VDDQ. 3. Peak to peak ac noise on VREF may not exceed +/- 2% VREF (dc). 4. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF and must track variations in die dc level of VREF. 5. VDDQ tracks with VDD, VDDL tracks with VDD. AC parameters are measured with VDD, VDDQ, and VDDL tied together. ODT DC Electrical Characteristrics: Parameter / Condition Symbol min. nom. max. Units Notes Rtt eff. impedance value for EMR(1)(A6,A2)=0,1; 75 ohm Rtt1(eff) 60 75 90 ohms 1 Rtt eff. impedance value for EMR(1)(A6,A2)=0,1; 150 ohm Rtt2(eff) 120 150 180 ohms 1 Rtt eff. impedance value for EMR(1)(A6,A2)=1,1; 50 ohm Rtt3(eff) 40 50 60 ohms 1 Deviation of VM with respect to VDDQ / 2 delta VM - 6.00 +6.00 % 2 1) Measurement Definition for Rtt(eff): Apply VIHac and VILac to test pin seperately, then measure current I(VIHac) and I(VILac) respectively. Rtt(eff) = (VIHac - VILac) /( I(VIHac) - I(VILac)) 2) Measurement Defintion for VM: Measure voltage (VM) at test pin (midpoint) with no load: delta VM =(( 2* VM / VDDQ) - 1 ) x 100% REV 1.3 09/2009 54 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die DC & AC Logic Input Levels DDR2 SDRAM pin timing are specified for either single ended or differential mode depending on the setting of the EMR(1) "Enable DQS" mode bit; timing advantages of differential mode are realized in system design. The method by which the DDR2 SDRAM pin timing are measured is mode dependent. In single ended mode, timing relationships are measured relative to the rising or falling edges of DQS crossing at VREF. In differential mode, these timing relationships are measured relative to the crosspoint of DQS and its complement, DQS. This distinction in timing methods is guaranteed by design and characterisation. In single ended mode, the DQS (and RDQS) signals are internally disabled and don't care. Single-ended DC & AC Logic Input Levels DDR2-533 Symbol DDR2-667 Parameter VIH (dc) DC input logic high VIL (dc) DC input low VIH (ac) AC input logic high VIL (ac) AC input low Units Min. Max. Min. Max. VREF + 0.125 VDDQ * VREF + 0.125 VDDQ * V - 0.3 VREF - 0.125 - 0.3 VREF - 0.125 V VREF + 0.250 VDDQ * VREF + 0.200 VDDQ * V -0.3 VREF - 0.250 -0.3 VREF - 0.200 V * VDDQ + 250mV is permitted, provided that 1.8V is not exceeded. Single-ended AC Input Test Conditions Symbol VREF VSWING(max) SLEW Condition Value Units Notes 0.5 * VDDQ V 1, 2 Input signal maximum peak to peak swing 1.0 V 1, 2 Input signal minimum slew rate 1.0 V / ns 3, 4 Input reference voltage 1. This timing and slew rate definition is valid for all single-ended signls execpt tis, tih, tds, tdh. 2. Input waveform timing is referenced to the input signal crossing through the VREF level applied to the device under test. 3. The input signal minimum slew rate is to be maintained over the range from VIL(dc)max to VIH(ac)min for rising edges and the range from VIH(dc)min to VIL(ac)max for falling edges as shown in the below figure. 4. AC timings are referenced with input waveforms switching from VIL(ac) to VIH(ac) on the positive transitions and VIH(ac) to VIL(ac) on the negative transitions. REV 1.3 09/2009 55 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Differential DC and AC Input and Output Logic Levels Symbol Parameter min. max. Units Notes VID(ac) AC differential input voltage 0.5 VDDQ + 0.6 V 1 VIX(ac) AC differential cross point input voltage 0.5 * VDDQ - 0.175 0.5 * VDDQ + 0.175 V 2 VOX(ac) AC differential cross point output voltage 0.5 * VDDQ - 0.125 0.5 * VDDQ + 0.125 V 3 Notes: 1) VID(ac) specifices the allowable DC execution of each input of differential pair such as CK, CK, DQS, DQS, LDQS, LDQS, UDQS, and UDQS. 2) VIX(ac) specifices the input differential voltage lVTR-VCPl required for switching, where VTR is the true input (such as CK, DQS, LDQS, or UDQS) level and VCP is the complementary input (such CK, DQS, LDQS, or UDQS ) level. The minimum value is equal to VIH(DC) - VIL(DC). 3) The typical value of VOX(AC) is expected to be about 0.5VDDQ of the transmitting device and VOX(AC) is expected to track variations in VDDQ. VOX(AC) indicates the voltage at which differential signals must cross. VDDQ VTR Crossing Point VID VCP VIX or VOX VSSQ SSTL18_3 REV 1.3 09/2009 56 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Output Buffer Levels Output AC Test Conditions Symbol VOTR Parameter Output Timing Measurement Reference Level Units Notes V 1 0.5 * VDDQ 1. The VDDQ of the device under test is referenced. Output DC Current Drive Symbol Parameter Units Notes IOH(dc) Output Minimum Source DC Current, nominal -13.4 mA 1, 3, 4 IOL(dc) Output Minimum Sink DC Current, nominal 13.4 mA 2, 3, 4 OCD Default Setting Table Symbol 09/2009 min. nominal max. Unit Ohms 6 Ohms 1,2,3 V / ns 1,4,5,7,8 - Pull-up / Pull down mismatch 0 - 4 - Output Impedance step size for OCD calibration 0 - 1.5 0.8 - 5.0 SOUT REV 1.3 Description Output Slew Rate Notes 57 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Full Strength Pullup Driver Characteristics Voltage (V) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 Current (mA) Minimum Maximum 0.00 0.00 -3.49 -7.95 -7.70 -15.90 -11.76 -23.85 -15.40 -31.80 -18.60 -39.75 -21.30 -47.70 -23.27 -55.55 -24.10 -62.95 -24.73 -69.55 -25.23 -75.35 -25.65 -80.35 -26.02 -84.55 -26.35 -87.95 -26.65 -90.70 -26.93 -93.00 -27.20 -95.05 -27.46 -97.05 -27.71 -99.05 -27.95 -101.05 4 6 8 1. 1. 1. 8 0. 2 6 0. 1. 4 0. 1 2 0. 0 0.00 -2 0 . 0 0 I out (mA) -4 0 . 0 0 M i ni m um M a xim u m -6 0 . 0 0 -8 0 . 0 0 -1 0 0 . 0 0 -1 2 0 . 0 0 V o ut (V ) REV 1.3 09/2009 58 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Full Strength Pulldown Driver Characteristics Current (mA) Voltage (V) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 Minimum 0.00 3.49 7.70 11.76 15.40 18.60 21.30 23.27 24.10 24.73 25.23 25.65 26.02 26.35 26.65 26.93 27.20 27.46 27.71 27.95 Maximum 0.00 7.95 15.90 23.85 31.80 39.75 47.70 55.55 62.95 69.55 75.35 80.35 84.55 87.95 90.70 93.00 95.05 97.05 99.05 101.05 120.00 100.00 I out (mA) 80.00 Minimum Maximum 60.00 40.00 20.00 4 6 8 1. 1. 1. 8 0. 2 6 0. 1. 4 0. 1 2 0. 0 0.00 Vout (V) REV 1.3 09/2009 59 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Reduced Strength Pulldown Driver Characteristics Voltage (V) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 Minimum 0.00 1.72 3.44 5.16 6.76 8.02 8.84 9.31 9.64 9.89 10.09 10.26 10.41 10.54 10.66 10.77 10.88 10.98 Maximum 0.00 4.77 9.54 14.31 19.08 23.85 28.62 33.33 37.77 41.73 45.21 48.21 50.73 52.77 54.42 55.80 57.03 58.23 59.43 60.63 70.00 60.00 I out (mA) 50.00 40.00 Minimum Maximum 30.00 20.00 10.00 0.00 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 Vout (V) REV 1.3 09/2009 60 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Reduced Strength Pullup Driver Characteristics Voltage (V) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 Minimum 0.00 -1.72 -3.44 -5.16 -6.76 -8.02 -8.84 -9.31 -9.64 -9.89 -10.09 -10.26 -10.41 -10.54 -10.66 -10.77 -10.88 -10.98 Maximum 0.00 -4.77 -9.54 -14.31 -19.08 -23.85 -28.62 -33.33 -37.77 -41.73 -45.21 -48.21 -50.73 -52.77 -54.42 -55.80 -57.03 -58.23 -59.43 -60.63 0.00 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 -10.00 I out (mA) -20.00 -30.00 Minimum Maximum -40.00 -50.00 -60.00 -70.00 Vout (V) REV 1.3 09/2009 61 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Calibrated Output Driver V-I Characteristics DDR2 SDRAM output driver characteristics are defined for full strength calibrated operation as selected by the procedure outlined in the Off-Chip Driver (OCD) Impedance Adjustment. The following tables show the data in tabular format suitable for input into simulation tools. The nominal points represent a device at exactly 18 ohms. The nominal low and nominal high values represent the range that can be achieved with a maximum 1.5 ohms step size with no calibration error at the exact nominal conditions only (i.e. perfect calibration procedire, 1.5 ohm maximum step size guarantedd by specification). Real system calibration error needs to be added to these values. It must be understodd that these V-I curves are represented here or in supplier IBIS models need to be adjusted to a wider range as a result of any system calibration error. Since this a system specific phenomena, it cannot be quantified here. the values in the calibrated tables represent just the DRAM portion of uncertainty while looking at one DQ only. If the calibration procedure is used, it is possible to cause the device to operate outside the bounds of the default device characterisitcs tables and figure. in such a situation, the timing paramters in the specification cannot be guaranteed. It is solely up to the system application to ensure that the device is calibrated between the minimum and maximum default values at all times. If this can't be guaranteed by the system calibration procedure, re-calibration policy and uncertainty with DQ to DQ variation, the it is recommende that only the default values to be used. The nominal maximum ad minmum values represent the change in impedance from nominal low and high as a result of voltage and temperature change from the nominal condition to the maximum and minimum conditions. If calibrated at an extreme condition, the amount of variation could be as much as from the nominal minimum to the nominal maximum or vice versa. Full Strength Calibrated Pulldown Driver Characteristics Voltage (V) Nominal Minimum (21 Ohms) Nominal Low (18.75 Ohms) Nominal (18 ohms) Nominal High (17.25 Ohms) Nominal Maximum (15 Ohms) 0.2 9.5 10.7 11.5 11.8 13.3 0.3 14.3 16.0 16.6 17.4 20.0 0.4 18.7 21.0 21.6 23.0 27.0 The driver characteristics evaluetion conditions are: Nominal 25oC (Tcase) , VDDQ = 1.55 V, typical process Nominal Low and Nominal High 25oC (Tcase), VDDQ = 1.55V, any process Nominal Minimum Toper(max), VDDQ = 1.475 V, any process Nominal Maximum 0oC (Tcase), VDDQ = 1.625 V, any process Full Strength Calibrated Pullup Driver Characteristics Voltage (V) Nominal Minimum (21 Ohms) Nomal Low (18.75 Ohms) Nominal (18 ohms) Nomal High (17.25 Ohms) Nominal Maximum (15 Ohms) 0.2 -9.5 -10.7 -11.5 -11.8 -13.3 0.3 -14.3 -16.0 -16.6 -17.4 -20.0 0.4 -18.7 -21.0 -21.6 -23.0 -27.0 The driver characteristics evaluetion conditions are: Nominal 25oC (Tcase) , VDDQ = 1.55 V, typical process Nominal Low and Nominal High 25oC (Tcase), VDDQ = 1.55V, any process Nominal Minimum Toper(max), VDDQ = 1.475 V, any process Nominal Maximum 0oC (Tcase), VDDQ = 1.625 V, any process REV 1.3 09/2009 62 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Input / Output Capacitance DDR2-533 Symbol CCK CDCK CI DDR2-667 DDR2-800 Parameter Input capacitance, CK and CK Input capacitance delta, CK and CK Input capacitance, all other input-only pins Units min. max. min. max. min. max. 1.0 2.0 1.0 2.0 1.0 2.0 pF - 0.25 - 0.25 - 0.25 pF 1.0 2.0 1.0 2.0 1.0 1.75 pF - 0.25 - 0.25 - 0.25 pF CDI Input capacitance delta, all other input-only pins CIO Input/output capacitance, DQ, DM, DQS, DQS, RDQS, RDQS 2.5 4.0 2.5 3.5 2.5 3.5 pF CDIO Input/output capacitance delta, DQ, DM, DQS, DQS, RDQS, RDQS - 0.5 - 0.5 - 0.5 pF REV 1.3 09/2009 63 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die IDD Specifications and Measurement Conditions IDD Specifications Symbol Parameter/Condition I/O DDR2-533 4-4-4 DDR2-667 5-5-5 DDR2-800 6-6-6 DDR2-800 5-5-5 Unit Notes max. IDD0 Operating Current x4/x8 x16 80 80 95 95 110 110 110 110 mA 1, 2 IDD1 Operating Current x4/x8 x16 75 100 85 115 100 140 100 140 mA 1, 2 all 8 8 8 8 mA 1, 2 IDD2N Precharge Standby Current x4/x8 x16 55 55 60 60 70 70 70 70 mA 1, 2 IDD2Q Precharge Quiet Standby Current: x4/x8 x16 38 38 40 40 45 45 45 45 mA 1, 2 MRS(12)=0 x4/x8 x16 25 25 27 27 29 29 29 29 mA 1, 2 MRS(12)=1 x4/x8 x16 11 13 11 13 11 13 11 13 mA 1, 2 IDD3N Active Standby Current x4/x8 x16 50 50 55 55 65 65 65 65 mA 1, 2 IDD4R Operating Current Burst Read x4/x8 x16 100 125 115 140 130 160 130 160 mA 1, 2 IDD4W Operating Current Burst Write x4/x8 x16 90 105 100 120 110 135 110 135 mA 1, 2 IDD5 Auto-Refresh Current (tRFC=tREFI) x4/x8 x16 157 157 157 157 173 173 173 173 mA 1, 2 IDD6 Self-Refresh Current for standard products all 9 9 9 9 mA 1, 2 IDD7 Operating Current x4/x8 x16 132 182 181 215 200 240 200 240 mA 1 IDD2P Precharge Power-Down Current Active PowerIDD3P Down Standby Current Note: 1. IDD specifications are tested after the device is properly initialized. IDD parameters are specified with ODT disabled. 2. Input slew rate = 1 V/ns. REV 1.3 09/2009 64 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die IDD Measurement Conditions Symbol Parameter/Condition IDD0 Operating Current - One bank Active - Precharge tCK =tCKmin.; tRC = tRCmin; tRAS = tRASmin; CKE is HIGH, CS is HIGH between valid commands. Address and control inputs are SWITCHING; Data bus inputs are SWITCHING; IDD1 Operating Current - One bank Active - Read - Precharge IOUT = 0 mA; BL = 4, tCK = tCKmin, tRC = tRCmin; tRAS = tRASmin; tRCD = tRCDmin, CL = CLmin.;AL = 0; CKE is HIGH, CS is HIGH between valid commands;Address bus inputs are SWITCHING,Data bus inputs are SWITCHING; IDD2P Precharge Power-Down Current: All banks idle; CKE is LOW; tCK = tCKmin.; Other control and address inputs are STABLE, Data Bus inputs are FLOATING. IDD2N Precharge Standby Current: All banks idle; CS is HIGH; CKE is HIGH; tCK = tCKmin.; Other control and address bus inputs are SWICHTING; Data bus inputs are SWITCHING. IDD2Q Precharge Quiet Standby Current:All banks idle; CS is HIGH; CKE is HIGH; tCK = tCKmin.; Other control and address bus inputs are STABLE; Data bus inputs are FLOATING. IDD3P(0) Active Power-Down Current: All banks open; tCK = tCKmin.;CKE is LOW; Other control and address inputs are STABLE; Data Bus inputs are FLOATING. MRS A12 bit is set to "0"( Fast Power-down Exit); IDD3P(1) Active Power-Down Current: All banks open; tCK = tCKmin.;CKE is LOW; Other control and address inputs are STABLE; Data Bus inputs are FLOATING. MRS A12 bit is set to "1"( Slow Power-down Exit); IDD3N Active Standby Current: All banks open; tCK = tCKmin.; tRAS = tRASmax.; tRP = tRPmin., CKE is HIGH; CS is HIGH between valid commands; Other control and address inputs are SWITCHING; Data Bus inputs are SWITCHING. IDD4R Operating Current - Burst Read: All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CLmin.; tCK = tCKmin.; tRAS = tRASmax., tRP = tRPmin., CKE is HIGH, CS is HIGH between valid commands; Address inputs are SWITCHING; Data bus inputs are SWITCHING; IOUT = 0mA. IDD4W Operating Current - Burst Write: All banks open; Continuous burst writes; BL = 4; AL = 0, CL = CLmin.; tCK = tCKmin.; tRAS = tRASmax., tRP = tRPmin.;CKE is HIGH, CS is HIGH between valid commands; Address inputs are SWITCHING; Data Bus inputs are SWITCHING. IDD5B Burst Auto-Refresh Current: tCK = tCKmin.; Refresh command every tRFC = tRFCmin interval; CKE is HIGH, CS is HIGH between valid commands; Other control and adress inputs are SWITCHING; Data bus inputs are SWITCHING. IDD5D Distributed Auto-Refresh Current: tCK = tCKmin.; Refresh command every tREFI interval; CKE is HIGH, CS is HIGH between valid commands; Other control and adress inputs are SWITCHING; Data bus inputs are SWITCHING IDD6 Self-Refresh Current: CKE 0.2V; external clock off, CK and CK at 0V; Other control and address inputs are FLOATING; Data Bus inputs are FLOATING. Operating Bank Interleave Read Current: IDD7 1. All bank interleaving reads; IOUT = 0 mA, BL =4, CL = CLmin., AL = tRCDmin. - 1*tCK; tCK = tCKmin., tRC = TRCmin.; tRRD = tRRDmin; tRCD = 1*tCK, CKE = HIGH, CS is HIGH between valid commands; Address bus inputs are STABLE during DESELECTS. 2. Timing pattern: - DDR2 -533 4-4-4: A0 RA0 D A1 RA1 D A2 RA2 D A3 RA3 D D D D D - DDR2 -667 5-5-5: A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D D D - DDR2 -800 6-6-6: A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D D D D D D D D - DDR2 -800 5-5-5: A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D D D D D D D 3. Legend : A=Activate, RA=Read with Auto-Precharge, D=DESELECT 1. 2. 3. 4. IDD specifications are tested after the device is properly initialized. IDD parameter are specified with ODT disabled. Data Bus consists of DQ, DM, DQS, DQS, RDQS, RDQS, LDQS, LDQS, UDQS and UDQS. Definitions for IDD : LOW is defined as VIN <= VILAC(max.); HIGH is defined as VIN >= VIHAC(min.); STABLE is defined as inputs are stable at a HIGH or LOW level FLOATING is defined as inputs are VREF = VDDQ / 2 SWITCHING is defined as: Inputs are changing between HIGH and LOW every other clock (once per two clocks) for adress and control signals, and inputs changing between HIGH and LOW every other clock (once per two clocks) for DQ signals not including mask or strobes 5. Timing parameter minimum and maximum values for IDD current measurements are defined in the following table. REV 1.3 09/2009 65 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die IDD Measurement Conditions (cont'd) For testing the IDD parameters, the following timing parameters are used: Parameter Symbol -37B DDR2-533 -3C DDR2-667 -AD DDR2-800 -AC DDR2-800 4-4-4 5-5-5 6-6-6 5-5-5 Unit CAS Latency CL 4 5 6 5 tCK Clock Cycle Time tCK 3.75 3 2.5 2.5 ns tRCD 15 15 15 12.5 ns tRC 60 60 60 57.5 ns x4 & x8 tRRD 7.5 7.5 7.5 7.5 ns x16 tRRD 10 10 10 10 ns Active to Read or Write delay Active to Active / Auto-Refresh command period Active bank A to Active bank B command delay Active to Precharge Command tRASmin 45 45 45 45 ns tRASmax 70000 70000 70000 70000 ns tRP 15 15 15 12.5 ns Precharge Command Period Refresh parameters Parameter Symbol 1Gb Unit Auto-Refresh to Active / Auto-Refresh command period tRFC 127.5 ns Average periodic Refresh interval REV 1.3 09/2009 tREFI 0C<=Tcase<=85C 7.8 85C<Tcase<=95C 3.9 s 66 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Electrical Characteristics & AC Timing - Absolute Specification Timing Parameter by Speed Grade Symbol -37B DDR2 -533 Parameter Clock cycle time, CL=x tCK -3C DDR2 -667 min max 3750 8000 Clock cycle time, CL=x, (Average) min max -AD DDR2 -800 min max -AC DDR2 -800 min Unit max ps 3000 8000 2500 8000 2500 8000 ps tCH CK, CK high-level width 0.45 0.55 0.48 0.52 0.48 0.52 0.48 0.52 tCK tCL CK, CK low-level width 0.45 0.55 0.48 0.52 0.48 0.52 0.48 0.52 tCK WL Write command to DQS associated clock edge tDQSS Write command to 1st DQS latching transition RL-1 RL-1 RL-1 RL-1 tCK -0.25 +0.25 -0.25 +0.25 -0.25 +0.25 -0.25 +0.25 tCK tDSS DQS falling edge to CK setup time 0.2 - 0.2 - 0.2 - 0.2 - tCK tDSH DQS falling edge hold time from CK 0.2 - 0.2 - 0.2 - 0.2 - tCK tDQSL,H DQS input low (high) pulse width (write cycle) 0.35 - 0.35 - 0.35 - 0.35 - tCK tWPRE Write preamble 0.35 - 0.35 - 0.35 - 0.35 - tCK tWPST Write postamble 0.4 0.60 0.40 0.60 0.40 0.60 0.40 0.60 tCK tIS Address and control input setup time 250 - 200 - 175 - 175 - ps tIH Address and control input hold time 375 - 275 - 250 - 250 - ps tIPW Address and control input pulse width (each input) 0.6 - 0.6 - 0.6 - 0.6 - tCK tDS DQ and DM input setup time differential strobe 100 - 100 - 50 - 50 - ps tDH DQ and DM input hold time differential strobe 225 - 175 - 125 - 125 - ps DQ and DM input pulse width (each input) 0.35 - 0.35 - 0.35 - 0.35 - tCK DQ output access time from CK / CK -500 +500 -450 +450 -400 +400 -400 +400 ps DQS output access time from CK / CK -450 +450 -400 +400 -350 +350 -350 +350 ps - tACmax - tACmax - tACmax - tACmax ps tLZ(DQS) DQS(/DQS) low-impedence time from CK / CK tACmin tACmax tACmin tACmax tACmin tACmax tACmin tACmax ps tLZ(DQ) DQ low-impedence time from CK / CK 2tACmin tACmax 2tACmin tACmax 2tACmin tACmax 2tACmin tACmax ps tDQSQ DQS-DQ skew (for DQS & associated DQ signals) - 300 - 240 - 200 - 200 ps tDIPW tAC tDQSCK tHZ tHP Data-out high-impedence time from CK / CK Clock half period min (tCL, tCH) tQHS Data hold skew factor tQH Data output hold time from DQS min (tCL, tCH) min (tCL, tCH) min (tCL, tCH) ps - 400 - 340 - 300 - 300 ps tHP-tQHS - tHP-tQHS - tHP-tQHS - tHP-tQHS - ps tRPRE Read preamble 0.9 1.1 0.9 1.1 0.9 1.1 0.9 1.1 tCK tRPST Read postamble 0.4 0.6 0.4 0.6 0.4 0.6 0.4 0.6 tCK Active bank A to Active bank x4/x8 (1k page size) B command period x16 (2k page size) 7.5 - 7.5 - 7.5 - 7.5 - ns tRRD 10 - 10 - 10 - 10 - ns tFAW Four Activate Window REV 1.3 09/2009 x4/x8 (1k page size) 37.5 37.5 - 35 - 35 - ns x16 (2k page size) 50 50 - 45 - 45 - ns 67 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Symbol Parameter -37B DDR2 -533 min -3C DDR2 -667 max -AD DDR2 -800 -AC DDR2 -800 Unit min max min max min max 2 - 2 - 2 - tCK - 15 - 15 - 15 - ns tCCD CAS A to CAS B command period 2 tWR Write recovery time 15 tDAL Auto-Precharge write recovery + precharge time WR+tRP - WR+tRP - WR+tRP - WR+tRP - tCK tWTR Internal Write to Read command delay 7.5 - 7.5 - 7.5 - 7.5 - ns tRTP Internal Read to Precharge command delay 7.5 7.5 - 7.5 - 7.5 - ns tCKE CKE minimum high and low pulse width 3 3 - 3 - 3 - tCK tXSNR Exit Self-Refresh to non-Read command tRFC+10 tRFC+10 - tRFC+10 - tRFC+10 - ns tXSRD Exit Self-Refresh to Read command 200 - 200 - 200 - tCK - 200 Exit precharge power-down to any valid command (other than NOP or Deselect) 2 - 2 - 2 - 2 - tCK tXARD Exit power down to any valid command (other than NOP or Deselect) 2 - 2 - 2 - 2 - tCK tXARDS Exit active power-down mode to Read command (slow exit, lower power) 7 - AL - 8 - AL - 8 - AL - tCK tAOND ODT turn-on delay 2 2 2 2 2 2 tCK tXP tAON tAONPD tAOFD 6 - AL 2 2 tAC(max) t (max) t (max) t (max) tAC(min) AC tAC(min) AC tAC(min) AC +1 +0.7 +0.7 +0.7 ODT turn-on tAC(min) ODT turn-on (Power-Down mode) tAC(min) 2tCK+tAC tAC(min) 2tCK+tAC tAC(min) 2tCK+tAC tAC(min) 2tCK+tAC ns +2 (max)+1 +2 (max)+1 +2 (max)+1 +2 (max)+1 ODT turn-off delay 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 ns tCK ODT turn-off tAC(min) tAC(max) t (max) t (max) t (max) tAC(min) AC tAC(min) AC tAC(min) AC +0.6 +0.6 +0.6 +0.6 ns tAOFPD ODT turn-off (Power-Down mode) 2.5tCK+ 2.5tCK+ 2.5tCK+ 2.5tCK+ tAC(min) t (min) t (min) t (min) tAC(max) AC tAC(max) AC tAC(max) AC tAC(max) +2 +2 +2 +2 +1 +1 +1 +1 ns tANPD ODT to power down entry latency 3 3 tAXPD ODT power down exit latency 8 8 tMRD Mode register set command cycle time 2 - 2 - 2 - 2 - tCK tMOD MRS command to ODT update delay 0 12 0 12 0 12 0 12 ns tOIT OCD drive mode output delay 0 12 0 12 0 12 0 12 ns tIS+tCK +tIH - tIS+tCK +tIH - tIS+tCK +tIH - tIS+tCK +tIH - ns tAOF tDELAY Minimum time clocks remain ON after CKE asynchronously drops LOW REV 1.3 09/2009 - 3 - 8 3 - 8 tCK tCK 68 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die General notes, which may apply for all AC parameters Genernal Note 1 : DDR2 SDRAM AC timing reference load The figure represents the timing reference load used in defining the relevant timing parameters of the device. It is not intended to either a precise representation of the typical system environment nor a depiction of the actual load presented by a production tester. System designers should use IBIS or other simulation tools to correlate the timing reference load to a system environment. Manufacturers will correlate to their production test conditions, generally a coaxial transmission line terminated at the tester electronics. VDDQ DUT DQ DQS DQS RDQS RDQS O u tp u t V T T = V D D Q /2 25ohm s T im in g re fe re n c e p o in t The output timing reference voltage level for single ended signals is the crosspoint with VTT. The output timing reference voltage level for differential signals is the crosspoint of the true ( e.g. DQS) and the complement (e.g. DQS) signal. Gernal Note 2 : Slew Rate Measurement Levels Output slew rate for falling and rising edges is measured between VTT - 250 mV and VTT + 250 mV for single ended signals. For differential signals (e.g. DQS / DQS) output slew rate is measured between DQS - DQS = - 500 mV and DQS - DQS = + 500 mV. Output slew rate is guaranteed by design, but is not necessarily tested on each device. VID is the magnitude of the difference between the input voltage on CK and the input voltage on CK, or between DQS and DQS for differential strobe. Input slew rate for single ended signals is measured from Vref(dc) to VIH(ac),min for rising edges from vref(dc) to VIL(ac),max for falling edges. For differential signals (eg. CK - CK) slew rate for rising edges is measured from CK - CK = -250mV to CK - CK =+500V (+250mV to -500mV for falling edges). Genernal Note 3 : DDR2 SDRAM output slew rate test load Output slew rate is characterized under the test conditions in below figure. VDDQ DUT DQ DQS DQS RDQS RDQS O utput V T T = V D D Q /2 25ohm s Test point REV 1.3 09/2009 69 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Genernal Note 4 : Differential data strobe DDR2 SDRAM pin timings are specified for either single ended mode or differential mode depending on the setting of the EMRS "Enable DQS" mode bit; timing advantages of differential mode are realized in system design. The method by which the DDR2 SDRAM pin timings are measured is mode dependent. In single ended mode, timing relationships are measured relative to the rising or falling edges of DQS crossing at VREF. In differential mode, these timing relationships are measured relative to the crosspoint of DQS and its complement, DQS. This distinction in timing methods is guaranteed by design and characterization. Note that when differential data strobe mode is disabled via the EMRS, the complementary pin, DQS, must be tied externally to VSS through a 20 ohms to 10K ohms resistor to insure proper operation. Genernal Note 5 : AC timings are for linear signal transitions. Genernal Note 6 : All voltages are referenced to VSS. Genernal Note 7 : These parameters guarantee device behavior, but they are not necessarily tested on each device. They may be guaranteed by device design or tester correlation. Genernal Note 8 : Tests for AC timing, IDD, and electrial (AC and DC) characteristics, may be conducted at nominal reference/supply voltage levels, but the related specifications and device operation are guaranteed for the full voltage range specified. REV 1.3 09/2009 70 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Input and Data Setup and Hold Time Timing Definition for Input Setup (tIS) and Hold Time (tIH) Address and control input setup time (tIS) is referenced from the input signal crossing at the VIH(ac) level for a rising signal and VIL(ac) for a falling signal applied to the device under test. Address and control input hold time (tIH) is referenced from the input signal crossing at the VIL(dc) level for a rising signal and VIH(dc) for a falling signal applied to the device under test CK CK t IS t t IH IS t IH V DDQ V IH(ac) min V IH(dc) min V REF V IL(dc) max V IL(ac) max V SS Timing Definition for Data Setup (tDS) and Hold Time (tDH) DQS Differential Input Waveform DQS Single-ended Input Waveform DQS V REF t DS t DH t t DS DH VDDQ VIH(ac) min VIH(dc) min VREF VIL(dc) max VIL(ac) max VSS 1. Data input setup time with differential data strobe enabled MR[bit10]=0, is referenced from the input signal crossing at the VIH(ac) level to the differential data strobe crosspoint for a rising signal, and from the input signal crossing at the VIL(ac) level tothe differential data strobe crosspoint for a falling signal applied to the device under test. Input waveform timing with single-endeddata strobe enabled MR[bit10]=1, is referenced from the input signal crossing at the VIH(ac) level to the data strobe crossing Vref for a rising signal, and from the input signal crossing at the VIL(ac) level to the single-ended data strobe crossing Vref for a falling signal applied to the device under test. 2. Data input hold time with differential data strobe enabled MR[bit10]=0, is referenced from the input signal crossing at the VIL(dc) level to the differential data strobe crosspoint for a rising signal and VIH(dc) to the differential data strobe crosspoint for a falling signal applied to the device under test. Input waveform timing with single-ended data strobe enabled MR[bit10]=1, is referenced from the input signal crossing at the VIL(dc) level to the single-ended data strobe crossing Vref for a rising signal and VIH(dc) to the single-ended data strobe crossing Vref for a falling signal applied to the device under test REV 1.3 09/2009 71 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Slew Rate Definition for Input and Data Setup and Hold Times Setup (tIS & tDS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIH(dc)min and the first crossing of VIH(ac)min. Setup (tIS & tDS) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VIL(dc)max and the first crossing of VIL(ac)max, (fig. A) If the actual signal is always earlier than the nominal slew rate line between shaded `dc to ac region', use nominal slew rate for derating value. If the actual signal is later than the nominal slew rate line anywhere between shaded `dc to ac region', the slew rate of a tangent line to the actual signal from the ac level to dc level is used for derating value.(fig.B) Hold (tIH & tDH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(dc)max and the first crossing of Vref. Hold (tIH & tDH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VIH(dc)min and the first crossing of Vref.(fig. A). If the actual signal is always later than the nominal slew rate line between shaded `dc to Vref region', use nominal slew rate for derating value. If the actual signal is earlier than the nominal slew rate line anywhere between shaded `dc to Vref region', the slew rate of a tangent line to the actual signal from the dc level to Vref level is used for derating value.(fig.B) t t S t H S t t H S t t H S t H VDDQ VIH(ac) min dc to ac region VIH(ac) min dc to ac region VIH(dc) min VIH(dc) min dc to Vref region dc to Vref region VREF VREF dc to Vref region dc to Vref region VIL(dc) max dc to ac region Delta TFS Delta TRH Delta TRS Delta TFS VIH(dc)min - VIL(ac)min Setup Slew Rate = Delta TRS VREF - VIL(dc)max = Delta TRH VIH(dc)min - VREF Hold Slew Rate = Delta TFH VIL(ac) max VIL(ac) max VSS VSS Delta TFS falling signal rising signal rising signal falling signal 09/2009 Delta TRH Delta TRS Delta TFH tangent line [VIL(dc)max - VIL(ac)max] Setup Slew Rate = Delta TFS tangent line [VIH(dc)min - VIL(ac)min] Setup Slew Rate = Delta TRS tangent line [REF - VIL(dc)max] Hold Slew Rate = Delta TRH tangent line [VIH(dc)min - VREF] Hold Slew Rate Fig. A REV 1.3 VIL(dc) max dc to ac region Delta TFH VIL(dc)max - VIL(ac)max Setup Slew Rate = Hold Slew Rate VDDQ = Delta TFH falling signal rising signal rising signal falling signal Fig. B 72 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Input Setup (tIS) and Hold (tIH) Time DeratingTable CK, CK Differential Slew Rate (DDR2-533) Command / Address Slew rate 2.0 V/ns 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.25 0.2 0.15 0.1 1.5 V/ns D tIS D tIH +187 +179 +167 +150 +125 +83 0 -11 -25 -43 -67 -110 -175 -285 -350 -525 -800 -1450 +94 +89 +83 +75 +45 +21 0 -14 -31 -54 -83 -125 -188 -292 -375 -500 -708 -1125 D tIS +217 +209 +197 +180 +155 +113 +30 +19 +5 -13 -37 -80 -145 -255 -320 -495 -770 -1420 1.0 V/ns D tIH +124 +119 +113 +105 +75 +51 +30 +16 -1 -24 -53 -95 -158 -262 -345 -470 -678 -1095 D tIS +247 +239 +227 +210 +185 +143 +60 +49 +35 +17 -7 -50 -115 -225 -290 -465 -740 1390 D tIH +154 +149 +143 +135 +105 +81 +60 +46 +29 +6 -23 -65 -128 -232 -315 -440 -648 -1065 CK, CK Differential Slew Rate (DDR2-667/800) Command / Address Slew rate 2.0 V/ns 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.25 0.2 0.15 0.1 1.5 V/ns 1.0 V/ns D tIS D tIH D tIS D tIH D tIS D tIH +15+143 +133 +120 +100 +67 0 -5 -13 -22 -34 -60 -100 -168 -200 -325 -517 -1000 +94 +89 +83 +75 +45 +21 0 -14 -31 -54 -83 -125 -188 -292 -375 -500 -708 -1125 +180 +173 +163 +150 +!60 +97 +30 +25 +17 +8 -4 -30 -70 -138 -170 -295 -487 -970 +124 +119 +113 +!05 +75 +51 +30 +16 -1 -24 -53 -95 -158 -262 -345 -470 -678 -1095 +210 +203 +193 +180 +160 +127 +60 +55 +47 +38 +36 0 -40 -108 -140 -265 -457 -940 +154 +149 +143 +135 +105 +81 +60 +46 +29 +6 -23 -65 -128 -232 -315 -440 -648 -1065 1. All units in ps. 2. For all input signals the total tIS (input setup time) and tIH (input hold time) required is calculated by adding the individual datasheet value to the derating value listed in the previous table. REV 1.3 09/2009 73 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Data Setup (tDS) and Hold Time (tDH) Derating Table DQS, DQS Differential Slew Rate (DDR2-533) DQ Slewrate (V/ns) 4.0 V/ns 2.0 1.5 1.0 0.9 0.8 0.7 0.6 0.5 0.4 D tDS 125 83 0 - D tDH 45 21 0 - 3.0 V/ns D tDS 125 83 0 -11 - D tDH 45 21 0 -14 - 2.0 V/ns D tDS 125 83 D tDH 45 21 0 0 -11 -25 - -14 -31 - 1.8 V/ns D tDS 95 12 1 -13 -31 - D tDH 33 12 -2 -19 -42 - 1.6 V/ns D tDS 24 13 -1 -19 -43 - D tDH 24 10 -7 -30 -59 - 1.4 V/ns D tDS 25 11 -7 -31 -74 - 1.2 V/ns 1.0 V/ns 0.8 V/ns D D D D D D D tDH tDS tDH tDS tDH tDS tDH 22 5 23 17 -18 5 -6 17 6 -47 -19 -35 -7 -23 5 -11 -89 -62 -77 -50 -65 -38 -53 -127 -140 -115 -128 -103 -116 1. All units in ps. 2. For all input signals the total tDS (setup time) and tDH (hold time) required is calculated by adding the individual datasheet value to the derating value listed in the previous table. DQS, DQS Differential Slew Rate (DDR2-667/800) DQ Slewrate (V/ns) 4.0 V/ns 2.0 1.5 1.0 0.9 0.8 0.7 0.6 0.5 0.4 3.0 V/ns 2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.2 V/ns 1.0 V/ns 0.8 V/ns D D D D D D D D D D D D D D D D D D tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH 100 63 100 63 100 63 112 75 124 87 136 99 148 111 160 123 172 135 67 42 67 42 67 42 79 54 91 66 103 78 115 90 127 102 139 114 0 0 0 0 0 0 12 12 24 24 36 36 48 48 60 60 72 72 -5 -14 -5 -14 -5 -14 7 -2 19 10 31 22 43 34 55 46 67 58 -13 -31 -13 -31 -13 -31 -1 -19 11 -7 23 5 35 17 47 29 59 41 -22 -54 -22 -54 -22 -54 -10 -42 2 -30 14 -18 26 -6 38 6 50 18 -34 -83 -34 -83 -34 -83 -22 -71 -10 -59 2 -47 14 -35 26 -23 38 -11 -60 -125 -60 -125 -60 -125 -48 -113 -36 -101 -24 -89 -12 -77 0 -65 12 -53 -100 -188 -100 -188 -100 -188 -88 -176 -76 -164 -64 -152 -52 -140 -40 -128 -28 -116 1. All units in ps. 2. For all input signals the total tDS (setup time) and tDH (hold time) required is calculated by adding the individual datasheet value to the derating value listed in the previous table. REV 1.3 09/2009 74 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Overshoot and Undershoot Specification AC Overshoot / Undershoot Specification for Address and Control Pins DDR2 -533 DDR2 -667 DDR2 -800 Units Maximum peak amplitude allowed for overshoot area 0.5 0.5 0.5 V Maximum peak amplitude allowed for undershoot area 0.5 0.5 0.5 V Maximum overshoot area above VDD 1.0 0.8 0.66 V.ns Maximum undershoot area below VSS 1.0 0.8 0.66 V.ns Parameter Volts (V) Maximum Amplitude Overshoot Area VDD VSS Undershoot Area Maximum Amplitude Time (ns) AC Overshoot / Undershoot Specification for Clock, Data, Strobe and Mask Pins DDR2 -533 DDR2 -667 DDR2 -800 Units Maximum peak amplitude allowed for overshoot area 0.5 0.5 0.5 V Maximum peak amplitude allowed for undershoot area 0.5 0.5 0.5 V Maximum overshoot area above VDDQ 0.28 0.23 0.23 V.ns Maximum undershoot area below VSSQ 0.28 0.23 0.23 V.ns Parameter Volts (V) Maximum Amplitude Overshoot Area VDDQ VSSQ Maximum Amplitude Undershoot Area Time (ns) REV 1.3 09/2009 75 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Package Dimensions (x4/x8; 60 balls; 0.8mmx0.8mm Pitch; BGA Package) BOTTOM VIEW TOP VIEW 6.4 0.8 9 +/- 0.1 Pin A1 Index 8.0 13 +/- 0.1 0.8 Pin A1 Index 60Balls Min. 0.40 Max. 0.50 Min. 0.25 Max. 0.40 Units: mm REV 1.3 09/2009 Min. 0.10 Max. 0.20 Max. 1.20 Min. 0.10 76 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Package Dimensions (x16; 84 balls; 0.8mmx0.8mm Pitch; BGA Package) BOTTOM VIEW TOP VIEW 6.4 9 +/- 0.1 Pin A1 Index 0.8 11.2 13 +/- 0.1 0.8 Pin A1 Index Min. 0.25 Max. 0.40 Min. 0.40 Max. 0.50 Max. 1.20 Min. 0.10 Units: mm REV 1.3 09/2009 Max. 0.20 84Balls Min. 0.10 77 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die Revision Log Rev Date 0.00 01/2008 Draft 0.1 01/2008 Preliminary Edition 0.2 01/2008 IDD Current Information Update 1.0 01/2008 Official Release 1.1 04/2008 Change the power supply spec from 1.55V to 1.5V. Correct typo. 1.2 05/2008 Change Volate supply upper limit from 1.5V+0.125V to 1.5V+0.1275V. Update dimensions. Update Pulldown & Pullup Driver Characteristics. 1.3 09/2009 Update IDD current P.64. REV 1.3 09/2009 Modification 78 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice. NT5TB256M4DE / NT5TB128M8DE /NT5TB64M16DG 1Gb DDR2 SDRAM D-Die (R) Nanya Technology Corporation. All rights reserved. Printed in Taiwan, R.O.C., 2007 The following are trademarks of NANYA TECHNOLOGY CORPORATION in R.O.C, or other countries, or both NANYA logo. Other company, product and service names may be trademarks or service marks of others. NANYA TECHNOLOGY CORPORATION (NTC) reserves the right to make changes without notice. NTC warrants performance of its semiconductor products and related software to the specifications applicable at the time of sale in accordance with NTC's standard warranty. Testing and other quality control techniques are utilize to the extent NTC deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Certain applications using semiconductor products may involve potential risks of death, personal injury, or severe property or environmental damage ("Critical Applications"). NTC SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTEND, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. Inclusion of NTC products in such applications is understood to be fully at the risk of the customer. Use of NTC products in such applications requires the written approval of an appropriate NTC officer. Question concerning potential risk applications should be directed to NTC through a local sales office. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards should be provided by customer to minimize the inherent or procedural hazards. NTC assumes no liability of applications assistance, customer product design, software performance, or infringement of patents or services described herein. Nor does NTC warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of NTC covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. NANYA TECHNOLOGY CORPORATION HWA YA Technology Park 669, FU HSING 3rd Rd., Kueishan, Taoyuan, Taiwan, R.O.C. The NANYA TECHNOLOGY CORPORATION home page can be found at http:\\www.nanya.com REV 1.3 09/2009 79 (c) NANYA TECHNOLOGY CORP. All rights reserved. NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice.