Datasheet 2 Cell / 3 Cell Narrow VDC Charger with SMBus Interface BD99950MUV General Description Key Specifications The BD99950MUV is a high-efficiency, synchronous Narrow VDC system voltage regulator and battery charger controller. It has two charge pumps which separately drive N-channel MOSFETs for automatic system power source selection. Charge voltage, charge current, AC adapter current and minimum system voltage can be programmed through SMBus. With a small inductor, PWM switching frequency can also be programmed by SMBus up to 1.2MHz. Structure Silicon Monolithic Integrated Circuit Features Input Voltage Range: 6.0V to 24.0V Output Voltage Range: 3.072V to 16.384V Charge Voltage Accuracy: 0.5% Switching Frequency: 600kHz to 1.2MHz Battery Standby Current: 17A (Typ) Operating Temperature Range: -10C to +85C Package N-channel MOSFETs available for Battery or Adapter Selection via Internal Charge Pumps Fast DPM Transient Response under Turbo Mode(<100s) Linear Mode Trickle Charge via BGATE Charge Pump Low Operating Current BGATE Charge Pump at 17A(typical) MLCC Output Capacitor High Light Load Efficiency for Energy Star and ErP Lot6 Fast Load Current Transient Response under No Battery or Dead Battery conditions NMOS-NMOS Synchronous Step-Down Controller Programmable 600kHz-1.2MHz Switching Frequency Programmable Charge Voltage (16mV resolution), Charger Current (64mA resolution), Input Current (64mA resolution), Minimum System Voltage (64mV resolution) 0.5% Charge Voltage Accuracy 3% Charge Current Accuracy 3% Input Current Accuracy 0.5% Minimum System Voltage Accuracy 2% 20x Input Current Amplifier Output Accuracy Integrated Loop Compensation Battery Learn Function AC Adapter Operating Range: 6.0V to 24.0V Off-State Battery Discharge Current at 15A 20pin 3.5mmx3.5mm QFN Package VQFN20PV3535 W(Typ) x D(Typ) x H(Max) 3.50mm x 3.50mm x 1.00mm VQFN20PV3535 Applications Ultrabook, Notebook PC, Ultra-mobile PC, Tablet PC Product structure : Silicon monolithic integrated circuit .www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 14 * 001 This product has no designed protection against radioactive rays 1/34 TSZ02201-0A1A0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Typical Application Circuit ADAPTER + ACP ACN ACGATE BOOT VCC HDRV SYSTEM PHASE ACDET LDRV REGN BD99950MUV SRP SRN BATTRM HOST ACOK BGATE SCL SMBus SDA BATTERY+ BATT IOUT GND Figure 1. Typical Application Circuit www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 GND SRN BGATE 15 SRP LDRV Pin Configuration (TOP VIEW) 14 13 12 11 10 BATT 9 SCL 8 SDA 19 7 IOUT 20 6 ACDET PHASE VCC BD99950MUV 1 2 3 4 5 ACOK 18 BATTRM 17 HDRV ACP BOOT ACGATE 16 ACN REGN 2/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Pin Descriptions Pin No. Pin Name Function Input current sense resistor negative input. Place a 1F ceramic capacitor from ACN to ACP for common-mode filtering. Input current sense resistor positive input. Place a 0.1F ceramic capacitor from ACP to GND for common-mode filtering. Charge pump output to drive adapter input n-channel MOSFETs. The ACDRV voltage is 6V above VCC during AC adapter insertion. Place a 5.1k resistor and a 0.01F capacitor to ground as a low pass filter to limit inrush current. Battery removal signal input When battery is removed, BGATE charge pump turns off. A high level indicates that the battery was removed. AC adapter voltage detection open drain output. The internal open drain NMOS turns off when ACDET pin voltage is between 2.4V and 3.15V. AC adapter voltage detection input. Valid AC adapter input range is set using resistors forming a voltage divider which are connected between ACDET & GND and ACDET & AC adapter. Buffered adapter or charge current output selectable with SMBus command. The IOUT voltage is 20 times the voltage in the sense resistor. Place a 0.1F or less ceramic decoupling capacitor from IOUT pin to GND. SMBus open-drain data I/O. Connect to SMBus data line from the host controller or smart battery Connect a 10k pull-up resistor according to SMBus specifications. SMBus open-drain clock input. Connect to SMBus clock line from the host controller or smart battery Connect a 10k pull-up resistor according to SMBus specifications. Battery voltage input. Connect a 510 resistor to the source of the n-channel MOSFET. Place a 0.1F ceramic capacitor from BATT to GND. Charge pump output to drive BATT to SRN n-channel MOSFET. BATDRV voltage must be 6V above BATT to turn on n-channel MOSFET. Connect a 510 resistor to the gate of the n-channel MOSFET. Charge current sense resistor negative input. Place a 0.1F ceramic capacitor from SRN to GND for common-mode filtering. Charge current sense resistor positive input. Place a 0.1F ceramic capacitor from SRP to GND for common-mode filtering. IC ground. 1 ACN 2 ACP 3 ACGATE 4 BATTRM 5 ACOK 6 ACDET 7 IOUT 8 SDA 9 SCL 10 BATT 11 BGATE 12 SRN 13 SRP 14 GND 15 LDRV Low-side power MOSFET driver output. Connect this pin to the gate of the low-side n-channel MOSFET. 16 REGN Linear regulator output. REGN is the output of the 5.25V linear regulator supplied from VCC. Connect a 1F ceramic capacitor from REGN to GND. 17 BOOT High-side power MOSFET driver power supply. Connect a 0.1F capacitor from BOOT to PHASE. 18 HDRV High-side power MOSFET driver output. Connect this pin to the gate of the high-side n-channel MOSFET. 19 PHASE High-side power MOSFET driver source. Connect this pin to the source of the high-side n-channel MOSFET. 20 VCC PAD PAD Input supply, diode OR from adapter. Place a 10 resistor and 1F capacitor to ground as a low pass filter to limit inrush current. Connect to ground www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 3/34 Range 0V to Adapter 0V to Adapter 0V to Adapter + 6V 0V to 5V 0V to 30V I/O I I O I O 0V to 5V I 0V to 5V O 0V to 5V 0V to 5V 0V to Battery 0V to Battery + 6V 0V to Battery 0V to Battery 0V 0V to 6V 0V to 5.5V 0V to Adapter + 5V -1V to Adapter + 5V -1V to Adapter 0V to Adapter 0V I/O I I O I I I O O I O I I - TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Block Diagram BD99950MUV ACGATE ACDRV CHARGE PUMP 3 ACOK 6 ACDET 17 BOOT 18 HDRV 19 PHASE 16 REGN 15 LDRV 14 GND ACOK_DRV 150ms/1.3s deglitch UVLO 3.7V VCC 5 ACDET Selector Logic 20 ACOVP 3.15V BATTRM 4 Trickle Charge BGATE ACOK VREF_ICHG 11 VFB BATDRV CHARGE PUMP BATT VREF+60mV 10 2.5V IOUT 2.4V BATOVP 7 MUX SRN_ LOWV SRN IOUT _SEL VCC ACP 2 ACN 1 VCC_SRN SRN+ 200mV 10X VREF_IAC ACP_ ACN ACOC 3 .33xVREF_IAC SRP 13 10X SRN 12 VCC PWM VREF _ICHG REGN LDO 900k Driver Logic WAKEUP Temp CV Amplifier . VFB TSHUT 175 VREF_CV 100k ACP-PHASE IFAULT_HI 450mV MINSYS Amplifier . PHASE-GND IFAULT_LO VFB SMBus Interface SDA SCL 8 9 Charge Option() Charge Current() Charge Voltage() Min Sys Voltage() Input Current() Manufacture ID() Device ID() CHARGE_EN VREF_MINSYS 135mV /230mV LEARN VREF _MINSYS PHASE-GND CHG_RCP VREF _CV VREF _ICHG VREF _IAC IOUT_ SEL WATCHDOG TIMER 175s(default) 2mV Figure 2. Block Diagram www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 4/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Absolute Maximum Ratings (over operating free-air temperature range (unless otherwise noted)) Parameter Rating Unit VCC, BATT, SRN, SRP -0.3 to 30.0 V ACN, ACP -0.3 to 40.0 V PHASE -2.0 to ACN+0.3 V ACGATE, BGATE, BOOT -0.3 to 35.0 V HDRV PHASE-0.3 to BOOT+0.3 V IOUT, LDRV BATTRM, ACDET, SDA, SCL, REGN,ACOK,PHASE-BOOT VCC-ACGATE,BATT-BGATE -0.3 to REGN+0.3 V -0.3 to 6.0 V -0.3 to 7.0 V ACP-ACN, SRP-SRN -0.3 to 0.3 V Power Dissipation 1.64 W Junction Temperature Range(Tj) -20 to 125 C Storage Temperature Range (Tstg) -55 to 150 C Conditions Board dimension:114.3mm x 76.2mm x 1.6mmt Surface Copper area: 2.25mm2 2nd and 3rd Copper area: 5505mm2 Ta over 25 C, subtracts 16.4mW/C Caution: Operating the IC over the absolute maximum ratings may damage the IC. In addition, it is impossible to predict all destructive situations such as short-circuit modes, open circuit modes, etc. Therefore, it is important to consider circuit protection measures, like adding a fuse, in case the IC is operated in a special mode exceeding the absolute maximum ratings Recommended Operating Conditions (over operating free-air temperature range (unless otherwise noted)) Parameter Symbol Min Typ Max Unit Adapter Voltage ADAPTER+ 6.0 18.0 24.0 V Output Voltage SYSTEM 3.0 - 17.0 V Battery Voltage (With Adapter Mode) BATTERY+ 0.0 - 17.0 V Battery Voltage (Only Battery Mode) BATTERY+ 5.4 - 17.0 V Operating Temperature Range (Ta) Topr -10 - 85 C (Note 3) Pd, ASO should not be exceeded Electrical Characteristics (VCC/ACP/ACN = 18.0V, BATT/SRP/SRN = 7.4V, PHASE = 0.0V, GND = 0V Ta=25 C (unless otherwise specified) ) Parameter Symbol Min Typ Max Unit IADP - 1.0 1.5 mA ACDET=0V IBATT1 - 17.0 30.0 A BGATE Charge Pump ON IBATT2 - 15.0 25.0 A BGATE Charge Pump OFF IBATT3 - - 240 A Switching Frequency 1 FOSC1 510 600 690 kHz Charge Option[10:9] = 00 Switching Frequency 2 FOSC2 720 800 880 kHz Charge Option[10:9] = 01 Switching Frequency 3 FOSC3 850 1000 1150 kHz Charge Option[10:9] = 10 Switching Frequency 4 FOSC4 1020 1200 1380 kHz Charge Option[10:9] = 11 REGN Output Voltage VREGN 4.9 5.2 5.5 V SMBus Operation Frequency FSMB 10 - 400 kHz Charge Voltage Charge Voltage Accuracy1 (SRN Terminal Voltage) Charge Voltage Accuracy2 (SRN Terminal Voltage) VCV1 8.358 8.400 8.442 V Charge Voltage() = 0x20D0 VCV2 12.516 12.592 12.667 V Charge Voltage() = 0x3130 Adapter Standby Current Battery Standby Current 1 (VACDET=0.0V) Battery Standby Current 2 (VACDET=0.0V, VBATTRM=3.3V) Battery Current (VVCC=18.0V) www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 5/34 Conditions TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Electrical Characteristics - continued Parameter Symbol Min Typ Max Unit Conditions ICHG1 3973 4096 4219 mA Charge Current() = 0x1000 ICHG2 1946 2048 2150 mA Charge Current() = 0x0800 ICHG3 921 1024 1126 mA Charge Current() = 0x0200 ICHG4 172 256 340 mA Charge Current() = 0x0100 ICHG5 - 192 - mA Charge Current() = 0x0140 ICHG6 64 128 192 mA Charge Current() = 0x0080 ICHGTRI - 256 - mA Charge Current() = 0x0800 ICHGTH - -180 - mA Below Trickle Charge Current IADP1 3973 4096 4219 mA Input Current() = 0x1000 IADP2 1946 2048 2150 mA Input Current() = 0x0800 IADP3 870 1024 1178 mA Input Current() = 0x0400 IADP4 384 512 640 mA Input Current() = 0x0200 VMINSYS1 6.113 6.144 6.175 V GIOUT - 20.0 - V/V (VIOUT)/(VACP- VACN) VIOUT1 802.8 819.2 835.6 mV (VACP- VACN)=40.96mV VIOUT2 174.1 204.8 235.5 mV (VACP- VACN)=10.24mV ACOK Comparator VACOK 2.376 2.400 2.424 V ACOK Comparator Hysteresis VACOK2 - 50 - mV ACDET falling ACOVP Comparator VACOVP1 3.050 3.150 3.250 V ACDET rising ACOVP Comparator Hysteresis VACOVP2 - 75 - mV ACDET falling VCC UVLO (L to H) VUVLO1 3.5 3.7 3.9 V VCC rising VCC UVLO Hysteresis VUVLO2 - 300 - V VCC falling VCC to SRN Comparator VVCCOK1 - 200 - mV VCC rising above SRN VCC to SRN Comparator Hysteresis Charge Current Charge Current Accuracy (10m current sense resistor) Trickle Charge Current (10m current sense resistor, BATT < Minimum System Voltage) Trickle Charge to Fast Charge Detect Threshold Input Current Adapter Current Accuracy (20m current sense resistor) Minimum System Voltage Minimum System Voltage Accuracy (SRN Terminal Voltage) IOUT Amplifier IOUT Terminal Voltage Accuracy Minimum System Voltage() =0x1800<default at POR> Comparator ACDET rising for 19V Adapter VVCCOK2 - 100 - mV VCC falling toward SRN High Side FET OCP VHOCP 200 450 900 mV Low Side FET OCP 1 VLOCP1 70 135 220 mV Low Side FET OCP 2 VLOCP2 140 230 340 mV VOVP 300 600 900 mV ACP to PHASE Charge Option[7] = 0 PHASE to GND Charge Option[7] = 1 PHASE to GND Above Charge Voltage VCC to ACGATE Voltage VACGATE 5.0 6 6.5 V ACGATE Discharge Resistor RACGATE - 2 5 k BATT to BGATE Voltage VBGATE 5.0 6 6.5 V BGATE Discharge Resistor RBGATE - 250 500 SRN OVP Power Select N-Channel FET Gate Driver www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 6/34 VACGATE - VVCC VBGATE - VBATT TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Electrical Characteristics - continued Switching Driver IBOOT - 50 - A HDRV PMOS ON Resistance RHDRVP - 6.0 10.0 ID = -10mA HDRV NMOS ON Resistance RHDRVN - 0.65 1.3 ID = 10mA LDRV PMOS ON Resistance RLDRVP - 7.5 12.0 ID = -10mA LDRV NMOS ON Resistance RLDRVN - 0.9 1.4 ID = 10mA Dead Time TDEAD - 30 - ns BATTRM Input H VINH 2.5 - 5.5 V BATTRM Input L VINL 0.0 - 0.3 V BATTRM Pull Down Resistor RPD - 500 - k IACOKLK -1.0 0.0 1.0 A BOOT Terminal Current Others ACOK Leak Current www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 7/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Typical Performance Curves (Adapter = 19V, 2S2P Li-Battery, Ta = +25C (unless otherwise specified.)) ACGATE 10V/div Adapter 10V/div Adapter 10V/div ACDET 2V/div ACOK 5V/div ACOK 5V/div REGN 5V/div Charge Current 2A/div 200msec/div 2msec/div Figure 3. Adapter Insert to ACOK Figure 4. ACOK to Charge Start ACGATE 10V/div PHASE 10V/div Adapter 10V/div HDRV 10V/div ACOK 5V/div LDRV 5V/div Charge Current 500mA/div Inductor Current 2A/div 1msec/div 1sec/div Figure 6. SLLM (Variable Frequency) Mode Light Load Switching Waveform Figure 5. ACOK to Trickle Charge Start www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 8/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Typical Performance Curves - continued HDRV 10V/div HDRV 10V/div PHASE 10V/div PHASE 10V/div LDRV 2V/div LDRV 2V/div Inductor Current 2A/div Inductor Current 2A/div 500nsec/div 500nsec/div Figure 8. Continuous Conduction Mode Switching Waveform Figure 7. Fixed Frequency Mode Light Load Switching Waveform Adapter Current 2A/div System Voltage 0.5V/div(AC) Battery Current 2A/div Battery Voltage 5V/div System Current 2A/div System Current 5V/div V = -900mV (DCM to CCM) 500sec/div Figure 9. System Current Load Transient (Input DPM and Battery Discharging) www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 50sec/div Figure 10. No-Battery System Current Load Transient (0A to 5A) 9/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Typical Performance Curves - continued System Voltage 0.5V/div(AC) System Voltage 0.5V/div(AC) System Current 2A/div System Current 2A/div V = -100mV (CCM to CCM) 50sec/div V = -585mV Figure 11. No-Battery System Current Load Transient (2A to 5A) 100sec/div Figure 12. Trickle Charge Mode System Current Transient (0A to 5A) SDA 5V/div System Voltage 0.5V/div(AC) SCL 5A/div Charge Current 1A/div System Current 2A/div V = -115mV 100sec/div 2msec/div Figure 13. Trickle Charge Mode System Current Transient (2A to 5A) www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 Figure 14. Charge Current Setting Change (2.560A to 3.072A) 10/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Typical Performance Curves - continued SDA 5V/div SDA 5V/div SCL 5A/div SCL 5A/div Charge Current 1A/div Charge Current 1A/div 2msec/div 2msec/div Figure 15. Charge Current Setting Change (3.072A to 2.560A) Figure 16. Charge Current Setting Change (1.024A to 3.072A) SDA 5V/div Battery Voltage 2V/div System Voltage 2V/div SCL 5A/div Charge Current 1A/div Battery Current 2A/div 2msec/div Peak voltage = 9.14V V = 740mV Figure 17. Charge Current Setting Change (3.072A to 1.024A) www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 20msec/div Figure 18. Battery Removed 11/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Typical Performance Curves - continued System Voltage 2V/div System Voltage 2V/div Battery Voltage 2V/div Battery Voltage 2V/div BATTRM 10V/div BATTRM 10V/div Battery Current 2A/div Battery Current 500mA/div 500sec/div 2msec/div Figure 19. Battery Insertion (BATTRM=H to L or Charge Option[11]=1 to 0) Figure 20. Low Battery Insertion (BATTRM =H to L or Charge Option[11]=1 to 0) Adapter Current 2A/div System Voltage 2V/div Battery Current 2A/div System Current 5A/div 1msec/div Figure 21. System Current Load Transient (Fully Charged Battery 0x14=0000) www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 12/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Typical Performance Curves - continued Figure 22. Battery Voltage vs. Charge Current Figure 23. System Current vs. Adapter Current / Charge Current Fig.24 SLLM Mode Output Current vs. Efficiency www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 13/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Operating Description SMBus Protocols Write - Word Format SLAVE ADDRESS S 7bits W A 1bit 1bit 0b 0001001 0 0 REGISTER ADDRESS A 8bits 1bit MSB LSB 0 0x12H 0x14H 0x15H 0x3EH 0x3FH LOW DATA BYTE A 8bits 1bit MSB LSB 0 HIGH DATA BYTE A 8bits 1bit MSB LSB P 0 Charge Option Charge Current Charge Voltage Minimum System Voltage Adapter Current Read - Word Format SLAVE ADDRESS S 7bits W A 1bit 1bit 0b 0001001 0 0 REGISTER ADDRESS A 8bits 1bit 7bits 0 0b 0001001 MSB LSB 0x12H 0x14H 0x15H 0x3EH 0x3FH 0xFEH 0xFFH SLAVE ADDRESS S R A LOW DATA BYTE A 8bits 1bit 1bit 1bit 1 0 MSB LSB 0 HIGH DATA BYTE N 8bits 1bit MSB LSB P 1 Charge Option Charge Current Charge Voltage Minimum System Voltage Adapter Current Manufacture ID Device ID S START CONDITION A ACKNOWLEDGE R READ BIT MASTER TO SLAVE P STOP CONDITION N NOT ACKNOWLEDGE W WRITE BIT SLAVE TO MASTER SMBus Communication Timing Waveforms tSU(STA) tW(H) tW(L) SCL tr SDA START tH(STA) tH(DAT) tSU(DAT) tH(DAT) STOP SCL SDA ACK START tsu(STOP) SCL SDA t(BUF) STOP www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 14/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV SMBus Timing Specification Parameter Symbol Min Typ Max Unit FSMBus 10 - 400 kHz SDA/SCL Input Low Voltage VINL 0.0 - 0.8 V SDA/SCL Input High Voltage VINH 2.1 - 5.5 V SDA Hold Time from SCL TH(DAT) 250 - - ns SDA Setup Time from SCL TSU(DAT) 300 - - ns Start Condition Hold Time from SCL TH(STA) 4 - - s Start Condition Setup Time from SCL TSU(STA) 4.7 - - s Stop Condition Setup Time from SCL TSU(STOP) 4 - - s TBUF 4.7 - - s SMBus Frequency Bus Free Time SCL Low Timeout TTO(SCL) - 25 - ms Watch Dog Timer TWDI 140 175 220 s SLAVE Device Address of BD99950MUV Table 1. SLAVE ADDRESS + R 0b00010011 SLAVE ADDRESS + W Condition (0x13)H 0b00010010 (0x12)H Battery Charger Command The BD99950MUV supports the following 7 registers: Table 2. REGISTER REGISTER NAME READ/WRITE ADDRESS 0x12H Charge Option Read or Write DESCRIPTION POR STATE Charge Option 0xF302H 0x14H Charge Current Read or Write 7-bit Charge Current Setting 0x0000H 0x15H Charge Voltage Read or Write 11-bit Charge Voltage Setting 0x2000H(8.192V) 0x3EH Minimum System Voltage Read or Write 6-bit Minimum System Voltage Setting 0x1800H(6.144V) 0x3FH Input Current Read or Write 7-bit Input Current Setting 0x0800H(2.048A) 0xFEH Manufacturer ID Read Only Manufacturer ID 0x001FH 0xFFH Device ID Read Only Device ID 0x0001H Enable of Charge The conditions which make SMBus communication possible are as follows: REGN voltage is above 4.0V. VCC voltage is above 5.0V. When all conditions are not satisfied, reset will occur and register settings will return to their POR states. Battery Discharge Assistant Function when System Power Supply is more than AC adapter power When the system load requires power more than what the AC adapter can provide due to the Turbo-Boost function of the CPU while charging in CC or CV mode, power insufficiency can be compensated by a battery. Also, charge current is set to 0mA when charging is complete and when it turns to Battery Discharge mode during which the external FET (Q4) of battery side is off, the BGATE terminal charge pump automatically activates and by turning on Q4, high efficiency discharge is achieved. When Charge Option [11] is set to 1, the BGATE terminal charge pump continuously stays off. ACOC Function When more than 333% of the set AC adapter current is detected, HDRV terminal becomes low and the high-side FET turns off. Switching automatically starts when ACOC condition is released. High-Side FET OCP Function When PHASE voltage drops 450mV from the ACP voltage while HDRV voltage is high, over-current condition is detected and high-side FET turns off. Upon destruction of the low-side FET, avoid using the protection circuit under normal operation. www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 15/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Low-Side FET OCP function When PHASE voltage exceeds 135mV more than the ACP voltage while LDRV voltage is high, over-current condition is detected and low-side FET turns off. Upon destruction of the high-side FET, avoid using the protection circuit under normal operation. Battery Over Voltage Protection(BATTOVP) The system voltage rises when battery is suddenly disconnected while charging in CC mode. The SRN pin's OVP function is built-in to avoid over-voltage to be supplied to the system. The chip will not allow the high-side and low-side MOSFET to turn-on when the battery voltage at SRN exceeds 600mV more than the charge voltage set-point. If the chip detects SRN terminal OVP, the high-side FET and low-side FET are turned off. Upon release from the OVP condition, it automatically returns to its normal state and restarts switching. Watchdog Timer The BD99950MUV chip includes a watchdog timer to terminate charging if it does not receive a write command to the Charge Voltage() or Charge Current() registers within 175s. If a watchdog timeout occurs, all register values are left as is, however, charging is suspended. Charging also stops when SCL voltage stays low for more than 25ms since this signifies that the power supply may have turned off. To reset the watchdog timer and resume charging, the write commands to the Charge Voltage() or Charge Current() registers must be resent. The watchdog timer can also be disabled, or set to 44s, 88s or 175s via SMBus. LEARN Mode The battery LEARN cycle can be activated via SMBus command using the Charge Option() bit[6]. Set the bit to 1 to enable the battery LEARN cycle and 0 to disable it. When the LEARN function is enabled while the AC Adapter is connected, the system power source switches to battery. The LEARN function allows the battery to discharge in order to calibrate the battery gauge over a complete discharge/charge cycle. The controller automatically exits LEARN cycle when the battery voltage is below the set value of Minimum System Voltage(). The system then switches back to adapter input. ACOK and ACOVP Function The BD99950MUV uses an ACOK comparator to determine the source of AC Adapter voltage. An external resistor voltage divider attenuates the AC adapter voltage before it goes to ACDET. The AC adapter detect threshold should typically be programmed to a value greater than the maximum battery voltage, but lower than the maximum allowed AC adapter voltage. The open drain ACOK output requires an external pull-up resistor to system digital rail for a high level. It can be pulled to external rail under the following conditions: VCC Voltage > 5.0V 2.4V < ACDET Voltage < 3.15V VCC Voltage - SRN Voltage > 300mV After the first IC power on reset, the ACOK rising edge delay is always 1.3s. Set the Charge Option() bit[15] to 0 to set the rise deglitch time to 150ms. When the ACDET pin voltage is higher than 3.15V, it is considered as AC adapter over voltage. ACOK will be pulled low, and charging will be disabled. The ACGATE Charge Pump will be turned off to disconnect the high voltage AC adapter during ACOVP. When ACDET pin voltage falls below 3.15V and above 2.4V, it is considered as the adapter voltage returning back to its normal voltage. ACOK will be pulled high by an external pull up resistor. Transition from Trickle Charge mode to Fast Charge mode Transition from trickle charge to CC charge (fast charge mode) occurs by detecting the decrease in trickle charge current. When the trickle charge current drops to less than 100mA from its set value, it automatically switches to CC charge (fast charge). To enable the transition to fast charge, the charge current must be set to more than 256mA. www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 16/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Charge OCP When the charging current exceeds 100mA more than the set charge current, the DAC and charger restart to protect the battery from over current. Over Charge Voltage Setting Protection When a write to the Charge Voltage() register is detected during CV charging mode, charging resets to protect battery from over-current. Setting Charge Options The charge options are set by writing a valid 16-bit number to the charge option register. Each bit in the control register has a different function. Table 3 describes the function of each bit. Bits 2 and 4 are controlled internally and are read only. Table 3. Charge Options Register (0x12H) BIT [15] [14:13] BIT NAME ACOK Deglitch Time Setting Watchdog Timer Setting [12] SLLM mode [11] BGATE Charge Pump Enable [10:9] [8] [7] Switching Frequency setting High Side FET OCP Comparator Threshold Setting Low Side FET OCP Comparator Threshold Setting [6] LEARN Enable [5] IOUT Selection [4] ACOK Indication (Read Only) [3] Charge Over Current Protection [2] Trickle Charge Indication (Read Only) [1] ACOC Enable [0] Shut down www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 DESCRIPTION 0: ACOK rising edge deglitch time 150ms 1: ACOK rising edge deglitch time 1.3s <default at POR> 00: Disable Watchdog Timer 01: Enabled, 44 sec 10: Enabled, 88 sec 11: Enable Watchdog Timer (175s) <default at POR> 0: Fixed Frequency Switching 1: Variable Frequency Switching(SLLM mode)<default at POR> 0: BGATE Charge Pump ON <default at POR> 1: BGATE Charge Pump OFF(from HOST when battery is removed) 00: 600kHz 01: 800kHz <default at POR> 10: 1MHz 11: 1.2MHz 0: function is disabled 1: 450mV <default at POR> 0: 135mV <default at POR> 1: 230mV 0: Disable LEARN Cycle <default at POR> 1: Enable LEARN Cycle 0: IOUT is the 20x Adapter Current Amplifier Output <default at POR> 1: IOUT is the 20x Charge Current Amplifier Output Adapter Detection Indicator 0: AC adapter is not present (ACDET < 2.4V) <default at POR> 1: AC adapter is present (ACDET > 2.4V) 0: Charge Current DAC Reset and Charger Restart <default at POR> 1: Charge Current DAC Reset Trickle Charge Indicator 0: Charge in Switching Mode <default at POR> 1: In Trickle Charge mode(Linear charge mode ) 0: ACOC Disable 1: 3.33x of Adapter Current Setting <default at POR> 0: Enable NVDC Charger Control <default at POR> 1: Shut Down 17/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Setting the Charge Voltage The charge voltage is set by writing a valid 16-bit number to the Charge Voltage register. The first 4 LSBs are ignored and the next 11 bits are used to set the charge voltage through a DAC. The charge voltage range of the BD99950MUV is 3.072V to 16.384V. The register address for charge voltage is 0x15. The 16-bit binary number formed by D15-D0 represents the charge voltage set point in mV. However, the resolution becomes 16mV because the D0-D3 bits are ignored. The D15 bit is also ignored because it is not needed to span the 3.072V to 16.384V range. Table 4. Charge Voltage Register (0x15H) BIT BIT NAME 0 - Not used 1 - Not used 2 - Not used 3 - Not used 4 Charge Voltage, DACV 0 5 Charge Voltage, DACV 1 6 Charge Voltage, DACV 2 7 Charge Voltage, DACV 3 8 Charge Voltage, DACV 4 9 Charge Voltage, DACV 5 10 Charge Voltage, DACV 6 11 Charge Voltage, DACV 7 12 Charge Voltage, DACV 8 13 Charge Voltage, DACV 9 14 Charge Voltage, DACV 10 15 - www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 DESCRIPTION 0 = Adds 0mV of charger voltage, 1024mV min 1 = Adds 16mV of charger voltage 0 = Adds 0mV of charger voltage, 1024mV min 1 = Adds 32mV of charger voltage 0 = Adds 0mV of charger voltage, 1024mV min 1 = Adds 64mV of charger voltage 0 = Adds 0mV of charger voltage, 1024mV min 1 = Adds 128mV of charger voltage 0 = Adds 0mV of charger voltage, 1024mV min 1 = Adds 256mV of charger voltage 0 = Adds 0mV of charger voltage, 1024mV min 1 = Adds 512mV of charger voltage 0 = Adds 0mA of charger voltage 1 = Adds 1024mV of charger voltage 0 = Adds 0mV of charger voltage 1 = Adds 2048mV of charger voltage 0 = Adds 0mV of charger voltage 1 = Adds 4096mV of charger voltage 0 = Adds 0mV of charger voltage 1 = Adds 8192mV of charger voltage 0 = Adds 0mV of charger voltage 1 = Adds 16384mV of charger voltage, 16384mV max Not used. 18/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Setting the Charge Current The charge current is set by writing a valid 16-bit number to the Charge Current register. The first 6 LSBs are ignored and the next 7 bits are used to set the charge current through a DAC. The charge current range of the BD99950MUV is 128mA to 8.128A. The register address for charge current is 0x14. The 16-bit binary number formed by D15-D0 represents the charge current set point in mA. However, the resolution becomes 64mA because the D0-D5 bits are ignored. The D13-D15 bits are also ignored because they are not needed to span the 128mA to 8.128A range. To change "Trickle Charge" to "Fast Charge", a setting of 256mA or higher is required. Table 5. Charge Current Register (0x14H), Using 10m Sense Resistor BIT BIT NAME 0 - Not used 1 - Not used 2 - Not used 3 - Not used 4 - Not used 5 - Not used 6 Charge Current, DACI 0 7 Charge Current, DACI 1 8 Charge Current, DACI 2 9 Charge Current, DACI 3 10 Charge Current, DACI 4 11 Charge Current, DACI 5 12 Charge Current, DACI 6 DESCRIPTION 0 = Adds 0mA of charger current 1 = Adds 64mA of charger current 0 = Adds 0mA of charger current 1 = Adds 128mA of charger current 0 = Adds 0mA of charger current 1 = Adds 256mA of charger current 0 = Adds 0mA of charger current 1 = Adds 512mA of charger current 0 = Adds 0mA of charger current 1 = Adds 1024mA of charger current 0 = Adds 0mA of charger current 1 = Adds 2048mA of charger current 0 = Adds 0mA of charger current 1 = Adds 4096mA of charger current, 8128mA max 13 - Not used 14 - Not used 15 - Not used www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 19/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Setting the Input Current The input current is set by writing a valid 16-bit number to the Input Current register. The first 7 LSBs are ignored and the next 7 bits are used to set the input current through a DAC. The input current range of the BD99950MUV is 512mA to 6.144A. The register address for input Current is 0x3F. The 16-bit binary number formed by D15-D0 represents the input current set point in mA. However, the resolution becomes 64mA because the D0-D5 bits are ignored. The D13-D15 bits are also ignored because they are not needed to span the 512mA to 6.144A range. To set for more than 6.144A the sense resistor must be changed to 10m. Table 6. Input Current Register (0x3FH), Using 20m Sense Resistor BIT BIT NAME 0 - Not used 1 - Not used 2 - Not used 3 - Not used 4 - Not used 5 - Not used 6 Charge Current, DACS 0 7 Charge Current, DACS 1 8 Charge Current, DACS 2 9 Charge Current, DACS 3 10 Charge Current, DACS 4 11 Charge Current, DACS 5 12 Charge Current, DACS 6 DESCRIPTION 0 = Adds 0mA of input current 1 = Adds 64mA of input current 0 = Adds 0mA of input r current 1 = Adds 128mA of input current 0 = Adds 0mA of input current 1 = Adds 256mA of input current 0 = Adds 0mA of input current 1 = Adds 512mA of input current 0 = Adds 0mA of input current 1 = Adds 1024mA of input current 0 = Adds 0mA of input current 1 = Adds 2048mA of input current 0 = Adds 0mA of input current 1 = Adds 4096mA of input current, 6144mA max 13 - Not used 14 - Not used 15 - Not used www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 20/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Setting the Minimum System Voltage The minimum system voltage is set by writing a valid 16-bit number to the Minimum System Voltage register. The first 6 LSBs are ignored and the next 8 bits are used to set the minimum system voltage through a DAC. The minimum system voltage range of the BD99950MUV is 3.072V to 10.24V. The register address for Minimum System Voltage is 0x3E. The 16-bit binary number formed by D15-D0 represents the minimum system voltage set point in mV. However, the resolution becomes 64mV because the D0-D5 bits are ignored. The D14-D15 bits are also ignored because they are not needed to span the 3.072V to 10.24V range. Table 7. Minimum System Voltage Register (0x3EH) BIT BIT NAME 0 - Not used 1 - Not used 2 - Not used 3 - Not used 4 - Not used 5 - Not used 6 Charge Current, DACV 0 7 Charge Current, DACV 1 8 Charge Current, DACV 2 9 Charge Current, DACV 3 10 Charge Current, DACV 4 11 Charge Current, DACV 5 12 Charge Current, DACV 6 13 Charge Current, DACV 7 DESCRIPTION 0 = Adds 0mV of minimum system voltage, 1024mV min 1 = Adds 64mV of minimum system voltage 0 = Adds 0mV of minimum system voltage, 1024mV min 1 = Adds 128mV of minimum system voltage 0 = Adds 0mV of minimum system voltage, 1024mV min 1 = Adds 256mV of minimum system voltage 0 = Adds 0mV of minimum system voltage, 1024mV min 1 = Adds 512mV of minimum system voltage 0 = Adds 0mA of minimum system voltage 1 = Adds 1024mV of minimum system voltage 0 = Adds 0mV of minimum system voltage 1 = Adds 2048mV of minimum system voltage 0 = Adds 0mV of minimum system voltage 1 = Adds 4096mV of minimum system voltage 0 = Adds 0mV of minimum system voltage 1 = Adds 8192mV of minimum system voltage, 10240mV max 14 - Not used 15 - Not used www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 21/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV External Components Selection Inductor and Output Capacitor Low ESR MLCC needs to be used to reduce ripple voltage. The inductance also has a great influence on ripple current which flows in the inductor. Ripple current that flows in inductor can be calculated using Formula (1). As shown in Formula (1), the bigger the coil is or the higher the switching frequency is, less ripple current flows. I L = (Vcc - VOUT) x VOUT [A](1) L x Vcc x f Ripple current must be 30-50% of the maximum output current. I L = 0.3 - 0.5 x IOUTMAX [A] L= (Vcc - VOUT) x VOUT [H] I x Vcc x f L ( I L : output ripple current IL IL f : sw itchingfrequency) Peak current must be set lower than the maximum current of the inductor. (Refer to inductor specification) In order to improve efficiency, lower DCR/ACR inductor is recommended. The increase of output ripple voltage may lower the charge current detection accuracy. 19V Adapter 2cell battery (fsw = 800kHz) Adapter Capability 10W 20W 30W 40W Max output Current 1.7A 3.4A 5.1A 6.8A Inductor(H) 4.7 3.3 3.3 or 2.2 2.2 Output Capacitor(F) SRP-SRN Sense Resistor(m) 22 33 44 44 10 10 10 10 ACDET Resistor An attenuated value of the AC adapter voltage is inputted to the ACDET pin using a voltage divider. Set the ACDET voltage so that the range is 2.4V to 3.15V when the AC adapter is inputted. To lower the response speed of UVP and OVP due to noise in the AC adapter, insert capacitor C16 parallel to resistor R7 for filtering. Example of setting AC Adapter Voltage 10.5V 12V 15V 16V 19V 20V 24V Battery 2cell 2cell 2cell/3cell 2cell/3cell 2cell/3cell 2cell/3cell 2cell/3cell R6() 150k 180k 180k 200k 240k 240k 270k R7() ACOK Voltage Rising Edge (typical) ACOVP Voltage Rising Edge (typical) 51k 51k 39k 39k 39k 36k 33k 9.5V 10.9V 13.5V 14.7V 17.2V 18.4V 22.0V 12.4V 14.3V 17.7V 19.3V 22.5V 24.2V 29.0V Reverse Input Protection Circuit A protection circuit can be inserted (refer to Figure 26) in case the polarity of the AC adapter or the battery is reversed. Switching Power MOSFET (Q1,Q2) To decrease switching loss and to improve efficiency, select a FET with a small on-resistance and less gate capacity. AC Adapter and Battery Pass Power MOSFET (Q3,Q4) To decrease loss during operation, choose a FET with a small on-resistance. www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 22/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV VCC Protection Filter when Inserting the AC Adapter Insert filter with 10/1F to prevent over-voltage caused by ringing when the AC adapter is inserted. ACP and ACN terminal are measured by increasing pressure of internal elements. ACN and ACP Differential Mode Noise Filtering When error is caused on the regulating current due to differential mode noise, insert a differential mode noise filter with 10/1F between the ACN and ACP pins. In this case, do not connect a capacitor between ACN and GND. 20m 10 0.1uF 1uF ACP ACN BD99950MUV SRP, and SRN Capacitor To prevent inaccuracies in current detection caused by common node noise, place a 0.1F- 1F capacitor as close as possible to the analog GND pin. 10m 0 0.1uF 0.1uF SRP SRN BD99950MUV Current Sensing Resistor During adapter hot plug-in, the parasitic inductance and the input capacitor from the adapter cable form a second order system. Thus adapter hot plug-in generate over voltage spike. The Voltage spike may be beyond IC Maximum Voltage and break the IC. As methods of solving for voltage spike, moving C1 capacitor between R1 and Q3. Adapter Voltage Adapter Voltage Adapter voltage when place C1 capacitor ACP node and hot Adapter voltage when place input capacitor directry Plug-in Adapter node and hot Plug-in PCB Layout Guideline Current Sensing Resistor The SRP/ACP and SRN/ACN connection must be laid out as shown in Figure 25. Also, connect a 0.1F capacitor to GND near the pin to decrease common mode noise. High Current Line High Current Line Current sense Line Current sense Line LDRV The LDRV pin is the gate drive terminal of the low-side N-channel MOSFET. Extremely high charging/discharging slew rate in the gate of the MOSFET can BD99950MUV cause a very large current to flow through the REGN, LDRV and GND terminals. It is therefore advisable to place the gate of the low-side Figure 25. Current Sense Kelvin Layout N-channel MOSFET to the LDRV pin as close as possible. Enclosing the path with a ground shield is also recommended to lessen the unwanted effects of noise. SRP / ACP SRN / ACN HDRV and PHASE The HDRV pin is the gate drive terminal of the high-side N-channel MOSFET. Extremely high charging/discharging slew rate in the gate of the MOSFET can cause a very large current to flow through the BOOT, HDRV and PHASE terminals. It is therefore advisable to place the gate of the high-side N-channel MOSFET to the HDRV pin as close as possible. Enclosing the path with a ground shield is also recommended to lessen the unwanted effects of noise. www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 23/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Figure 26. Reference Design Schematic Application Example www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 24/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Input Capacitor C1A (22F) Place input capacitor C1A, as close as possible to Q3 drain pin and ground. Input Capacitor C4 (10F) Place input capacitor C4, as close as possible to Q1 drain pin and Q2 source pin. Select C1A C4 for Fast DPM operation. Current Sense Resistor R1 (20m), R2 (10m) Current sense Kelvin layout must be followed. (Refer to "Current Sense Resistance" on page 23.) Current Sense Pin Capacitor C8, C10, C11 (0.1F), C17(1F), C9(Empty) and R11(10) Place input capacitor C8, C9, C10, C11 as close as possible to their corresponding sense pins. (Refer to "ACN and ACP Terminal Differential Mode Noise Filtering" on page 23.) REGN Output Capacitor C7 (1F) Place output capacitor C7 as close as possible to REGN pin and to ground. VCC Decoupling Capacitor C6 (1F) Place input decoupling capacitor C6 as close as possible to VCC pin and to ground. www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 25/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Selection of Components Externally Connected Reference Design Configuration Value QTY Rated Voltage Manufacture Part number Rohm HS8K1 X[mm] Y[mm] Z[mm] 3.0 3.0 0.8 2.0 2.0 0.8 3.3 3.3 0.8 2.0 2.0 0.8 3.3 3.3 0.8 2.0 2.0 0.8 3.3 3.3 0.8 1.6 1.6 0.5 6.5 7.4 3.0 ALPS GLMC2R201A 6.6 7.0 3.0 TOKO FDSD0630-H-2R2M 7.5 7.5 2.0 coilcraft XAL7020-222ME 1.5uH 4.0 4.0 1.8 coilcraft KA5013-AE 22uF 2.0 1.25 1.25 1 25V Murata GRM21BR61E226ME44# C2A,C2B 22uF 2.0 1.25 1.25 2 25V Murata GRM21BR61E226ME44# C3 10uF 2.0 1.25 1.25 1 25V Murata GRM219BR61E106KA12# C4 10uF 2.0 1.25 1.25 1 25V Murata GRM219BR61E106KA12# C5 0.1uF 1.0 0.5 0.5 1 16V Std. Ceramic Capacitor X5R 10% C6 1.0uF 1.0 0.5 0.5 1 25V Murata GRM155R61E105KA12 C7 1.0uF 1.0 0.5 0.5 1 16V Std. Ceramic Capacitor X5R 10% C8 0.1uF 1.0 0.5 0.5 2 25V Std. Ceramic Capacitor X5R 10% 0.1uF 1.0 0.5 0.5 2 25V Std. Ceramic Capacitor X5R 10% C12 0.01uF 1.0 0.5 0.5 1 16V Std. Ceramic Capacitor X5R 10% C13 4700pF 1.0 0.5 0.5 1 6.3V Std. Ceramic Capacitor X5R 10% C14 0.1uF 1.0 0.5 0.5 1 16V Std. Ceramic Capacitor X5R 10% C15(Optional) 100pF 1.0 0.5 0.5 1 16V Std. Ceramic Capacitor X5R 10% C16 0.01uF 1.0 0.5 0.5 1 16V Std. Ceramic Capacitor X5R 10% C17 1.0uF 1.0 0.5 0.5 1 16V Std. Ceramic Capacitor X5R 10% D1 - 1.0 0.6 0.4 1 30V Rohm RB520CS-30 R1 20m 2.0 1.2 0.3 1 - Rohm UCR10EVHFSR020 R2 10m 2.0 1.2 0.3 1 - Rohm PMR10EZPFU10L0 R3(Optional) R4,R8 (Optional) R5 5.1k 1.0 0.5 0.35 1 - Std. 1% 510 1.0 0.5 0.35 2 - Std. 1% 10 1.0 0.5 0.35 1 - Std. 1% R6 240k 1.0 0.5 0.35 1 - Std. 1% R7 39k 1.0 0.5 0.35 1 - Std. 1% R9(Optional) 1M 1.0 0.5 0.35 1 - Std. 1% R10(Optional) 3M 1.0 0.5 0.35 1 - Std. 1% R11 10 1.0 0.5 0.35 1 - Std. 1% 10k 1.0 0.5 0.35 1 - Std. 1% 2in1 Q1, Q2 Q3 Q4 Q5-1,Q5-2 (Optional) L C1A 2in1 2.2uH 1 2 1 30V 30V 1 30V 1 30V 1 - Rohm RF4E110GN Rohm RQ3E120GN Rohm RF4E110GN Rohm RQ3E120GN Rohm RF4E110GN Rohm RQ3E120GN Rohm EM6K31 C1B(EMPTY) C9(Empty) C10,C11 R40(Empty) R41(Empty) R42(Empty) R43(Empty) R45 www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 26/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Figure 27. TOP Silk Screen Figure 28. TOP Copper Trace Layer (Signal and Ground) Figure 29. Middle 1 Copper Trace Layer (Ground) Figure 30. Middle 2 Copper Trace Layer (Signal and System Output) Figure 31. Bottom Copper Trace Layer (Signal and Ground) Figure 32. Bottom Silk Screen www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 27/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Example of Recommended Circuit Adapter Reverse Input Protection (optional) Q5-1 ADAPTER + Q3 R1 R10 C4 C1A R11 C12 C17 R9 C8 R3 C9 ACP ACN ACGATE BOOT VCC HDRV C5 R5 R6 Q1 D1 L C6 ACIN R7 ( ) Total Csys100F LDRV REGN C15 SYSTEM C2A C2B PHASE Q2 C7 BD99950MUV SRP C10 R2 C11 HOST SRN BATTRM R4 ACOK Q4 BGATE SCL SMBus C16 SDA R8 C14 GND C13 BATTERY+ BATT IOUT Q5-2 C3 Battery Reverse Input Protection (optional) Figure 33. Example of Application Circuit (AC Adapter and Battery Reverse Input Protected Configuration) Q3 R1 ADAPTER + C4 C1A R11 C8 C17 ACP ACN BOOT ACGATE C5 R5 R6 VCC Q1 HDRV D1 L C6 PHASE C2A C2B SYSTEM ACIN R7 LDRV REGN Q2 C7 BD99950MUV SRP C10 HOST SRN BATTRM C11 ACOK SMBus Q4 BGATE R4 SCL SDA BATTERY+ BATT IOUT C13 R2 C3 GND Figure 34. Example of Application Circuit (Minimum Component Configuration) www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 28/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Power Dissipation [W] Power Dissipation Measuring instrument : TH-156(KUWANO Electrical Instrument Condition : Board mounting Board dimension : 114.3mm x 76.2mm x 1.6mmt 2.0 1.5 Four Layer (Surface Copper area 2.25mm2) (The 2nd and 3rd layer have 5505mm2 copper plane) (PCB with thermal vias) ja=61.0/W 1.64W 1.0 0.5 0 25 50 75 100 125 150 Ambient Temperature Ta [] Figure 35. Power Dissipation (Solder operated on the PAD backside of 4 layer substrate) www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 29/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the IC's power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. However, pins that drive inductive loads (e.g. motor driver outputs, DC-DC converter outputs) may inevitably go below ground due to back EMF or electromotive force. In such cases, the user should make sure that such voltages going below ground will not cause the IC and the system to malfunction by examining carefully all relevant factors and conditions such as motor characteristics, supply voltage, operating frequency and PCB wiring to name a few. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. Inrush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The IC's power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 30/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Operational Notes - continued 11. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. 12. Regarding the Input Pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a parasitic diode or transistor. For example (refer to figure below): When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be avoided. Resistor Transistor (NPN) Pin A Pin B C E Pin A N P+ P N N P+ N Pin B B Parasitic Elements N P+ N P N P+ B N C E Parasitic Elements P Substrate P Substrate GND GND Parasitic Elements GND Parasitic Elements GND N Region close-by Figure 36. Example of monolithic IC structure 13. Ceramic Capacitor When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with temperature and the decrease in nominal capacitance due to DC bias and others. 14. Area of Safe Operation (ASO) Operate the IC such that the output voltage, output current, and power dissipation are all within the Area of Safe Operation (ASO). 15. Thermal Shutdown Circuit(TSD) This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always be within the IC's power dissipation rating. If however the rating is exceeded for a continued period, the junction temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls below the TSD threshold, the circuits are automatically restored to normal operation. Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat damage. 16. Over Current Protection Circuit (OCP) This IC incorporates an integrated overcurrent protection circuit that is activated when the load is shorted. This protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should not be used in applications characterized by continuous operation or transitioning of the protection circuit. Ultrabook is trademarks of Intel Corporation in the U.S. and/or other countries. www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 31/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Ordering Information B D 9 9 9 5 Part Number 0 M U V - Package MUV: VQFN20PV3535 E2 Packaging and forming specification E2: Embossed tape and reel Marking Diagrams VQFN20PV3535 (TOP VIEW) Part Number Marking 1 2 3 4 5 LOT Number 1PIN MARK Part Number Marking BD99950 www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 Package Orderable Part Number VQFN20PV3535 BD99950MUV-E2 32/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Physical Dimension, Tape and Reel Information VQFN20PV3535 www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 33/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 BD99950MUV Revision History Date Revision 29.Aug.2013 001 06.Jan.2014 002 29.Jun.2015 003 08.Aug.2016 004 25.Jan.2019 005 Changes New Release Page.1 Charge Current Accuracy -> Charge Voltage Accuracy. Page.2 Figure.1 Change Typical Application Circuit. Page.8 Figure.4 Time division 200ms->2ms change. Page.23 Add sentence about Current Sensing Resistor. Page.24 Figure.26 Change Example of Recommended Circuit. Page.1 Modify Switching Frequency Range from 800kHz to 1200kHz to 600kHz to 1200kHz. Page.2 Modified Figure 1 of Typical Application circuit. Page.3 Modified ACN pin's Descriptions. Page.3 Modified BATT pin's Descriptions. Page.3 Modified BGATE pin's Descriptions. Page.5 Modified Power Dissipation in Absolute Maximum Rating table. Page.8 Modified Layout Figure 3,4,5,6. Page.9 Modified Layout Figure 7,8,9,10. Page.10 Modified Layout Figure 11,12,13,14. Page.11 Modified Layout Figure 15,16,17,18. Page 12 Modified Layout of Figure 19,20,21. Page.22 Modified External Components Selection. Page.24 Modified Figure 26 of Application Example. Page.25 Rename of External capacitor C1 to C1A. Page.25 Modified C1A's Descriptions. Page.25 Modified Current sense Resister and Capacitor of C8 , C10 , C11 , C9 , C17,and R11. Page.26 Modified List of Selection of Components Externally Connected, Pahe.27 Modified Figure of PCB Layout, Page.28 Modified Component name of Figure 33 and Figure 34. Page.33 Replacement High Resolution Graphic Data. Page.33 Physical Dimension, Tape and Reel Information www.rohm.com (c) 2019 ROHM Co., Ltd. All rights reserved. TSZ22111 * 15 * 001 34/34 TSZ02201-0J1J0A700570-1-2 25.Jan.2019.Rev.005 Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used. However, recommend sufficiently about the residue.) ; or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label A two-dimensional barcode printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.004 Datasheet General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the latest information with a ROHM sales representative. 3. The information contained in this document is provided on an "as is" basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or concerning such information. Notice - WE (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet bd99950muv - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS bd99950muv VQFN20PV3535 2500 2500 Taping inquiry Yes