A
30
SЕRIES
Subminiature DIL
relays 2 A
Electronic
circuit boards
Hi-Fi systems
Printers
Toys
Medical and
dentistry
Hoists and
cranes
Door and gate
openers
FINDER reserves the right to alter characteristics at any time without notice. FINDER assumes no liability for damage to persons or property, caused as a result of the incorrect use or application of its products.
A
Printed circuit mount
2A signal relay
• 2 Pole changeover contacts Low level switching
capability
• Subminiature - industry standard DIL package
• Sensitive DC coil - 200mW
• Wash tight: RT III
• Cadmium Free contact material
30.22
• Low coil power
• Au clad contacts
• PCB mount
Copper side view
Contact specification
Contact configuration 2 CO (DPDT)
Rated current/Maximum peak current A 2/3
Rated voltage/
Maximum switching voltage VAC 125/250
Rated load AC1 VA 125
Rated load AC15 (230VAC) VA 25
Single phase motor rating (230VAC) kW —
Breaking capacity DC1: 30/110/220 V A 2/0.3/—
Minimum switching load mW (V/mA) 10 (0.1/1)
Standard contact material AgNi + Au
Coil specification
Nominal voltage (UN) VAC (50/60Hz) —
VDC 5 - 6 - 9 - 12 - 24 - 48
Rated power AC/DC VA (50Hz)/W —/0.2
Operating range AC —
DC See table page 5
Holding voltage AC/DC —/0.35UN
Must drop-out voltage AC/DC —/0.05UN
Technical data
Mechanical life AC/DC cycles —/10·106
Electrical life at rated load AC1 cycles 100·103
Operate/release time ms 6/2
Insulation between coil
and contacts (1.2/50 µs) kV 1.5
Dielectric strength
between open contacts VAC 750
Ambient temperature range °C –40…+85
Environmental protection RT III
Approvals (according to type)
3
X-2017, www.findernet.com
30
SERIES
30 SERIES
Subminiature DIL relays 2A
A
Ordering information
Example: 30 series PCB relay, 2 CO (DPDT) - 2A contacts, 12V sensitive DC coil.
A B C D
3 0.2 2.7.0 1 2.0.0.1.0
Series
Type
2 = PCB mount
No. of poles
2 = 2 pole, 2A
Coil version
7 = Sensitive DC
Coil voltage
See coil specifications
A: Contact material
0 = Standard
AgNi + Au
B: Contact circuit
0 = CO (DPDT)
D: Special versions
0 = Wash tight (RT III)
C: Options
1 = None
Technical data
Insulation according to EN61810-1
Nominal voltage of supply system VAC 230/400 120…240 single phase
Rated insulation voltage VAC 250 125
Pollution degrees 1 2
Insulation between coil and contact set
Type of insulation Basic Basic
Overvoltage category I II
Rated impulse voltage kV (1.2/50µs) 1.5 1.5
Dielectric strength VAC 1000 1000
Insulation between adjacent contacts
Type of insulation Basic Basic
Overvoltage category I II
Rated impulse voltage kV (1.2/50µs) 1.5 1.5
Dielectric strength VAC 1500 1500
Insulation between open contacts
Type of disconnection Micro-disconnection Micro-disconnection
Dielectric strength VAC/kV (1.2/50µs) 750/1 750/1
Other data
Bounce time: NO/NC ms 1/3
Vibration resistance (5…55)Hz: NO/NC g 15/15
Shock resistance g 16
Power lost to the environment without contact current W 0.2
with rated current W 0.4
Recommended distance between relays mounted on PCB mm ≥5
4
X-2017, www.findernet.com
30 SERIES
Subminiature DIL relays 2A
30
SERIES
A
Contact specification
F 30 - Electrical life (AC1) v contact current (125V)
Cycles
Note:
The rated current of 2A corresponds to the limiting continuous current.
Coil specifications
DC coil data - 0.2W sensitive R 30 - DC coil operating range v ambient temperature
Nominal
voltage
Coil
code
Operating range
Resistance
Rated coil
consumption
UNUmin Umax RI at UN
V V V ΩmA
57.005 3.7 7.5 125 40
67.006 4.5 9 180 33
97.009 6.7 13.5 405 22
12 7.012 8.4 18 720 16
24 7.024 16.8 36 2880 8.3
48* 7.048 36 72 10000 4.8
* Rated power: 0.23W 1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
Please see general technical information 5
X-2017, www.findernet.com
30
SERIES
30 SERIES
Subminiature DIL relays 2A