SMA Straight Cable Connectors, Crimp Attachment 1314258-1, 1086486-1, 1314256-1, 1082032-1, 1314257-1, 10820341 AM _ 13137121, 1086273-1, 1313719-1, 1082036-1, 1084241-1, 1313710-1 and 1085274-1 Instruction Sheet 408-4736 (was A.P. 22-001} 07 FEBOO RevO EC 0990-0134-00 CONNECTOR CABLE TOOLS REQ'D CENTER CONTACT HOLDER: TYPE TYPE cae ee 7-2578) SMA. com SEE CRIMP TOOL 5698-5014-54 STRAIGHT TABLE FERRULE CRIMP DIE 5698-5015-54 CABLE CONNECTORS (29 8128 HED CRIMP ATTACHMENT 2098-0323-5 (151 HE CENTER CONTACT CRMP DIE 2598-5379-S4 (.042 HEX) OPTIONAL CRIMP TOOLING CRIMP TOOL 2598-5006-54 FERRULE CRIMP DIE 2598-5007-54 1213 & 128 HEX 2598-5380-54 (151 HEX) CENTER CONTACT i 2598-5380-54 (.042 HEX) FOR _SPEOFIC APPLICATION SEE TABLE ON SHEET 2 OF THS PROCEDLRE CONNECTOR - fs} - HOUSING iY CONTACT L FERRULE SUB-ASSEMBLY ASSEMBLY OPERATIONS 005 _ 085 "A ae 275 4.0 PREPARE COAXIAL CABLE END 330 .1 PLACE FERRULE ON CABLE. [2 REMOVE END PORTION OF CABLE JACKET TO EXPOSE CABLE QUTER CONDUCTOR. 1.3 TRIM OUTER CONDUCTOR TO LENGTH. 1.4 TRIM CABLE DIELECTRIC TO LENGTH. COTE INNER [5 FLARE OUTER CONDUCTOR, CABLE DIELECTRIC = CABLE QUTER CONDUCTOR FERRULE CABLE JACKET CENTER CONTACT HOLDER {(T-576) HEAT HERE 2,0 SOLDERING GF CENTER CONTACT TO CABLE INNER CONDUCTOR = 2.1 TIN _LNNER CONDUCTOR OF CABLE. 2.2 PLACE CONTACT IN HOLDER, HEAT CONTACT AND PUSH_IT OVER THE CABLE INNER CONDUCTOR TO REST FIRMLY |_| AGAINST THE CABLE DIELECTRIC AS SHOWN. 2.3 REMOVE EXCESS SOLDER. CONTACT BOTTOM HERE CABLE DIELECTRIC OPTIONAL CRIMPING OF THE CENTER CONTACT INSTEAD OF SOLDERING 3.0 CRIMPING OF CENTER CONTACT TO CABLE INNER CONDUCTOR 3.1 ASSEMBLE CONTACT OVER THE CABLE INNER CONDUCTOR UNTIL IT RESTS FRIMLY AGAINST THE CABLE OIELECTRIC AS SHOWN. 3.2 HOLD CONTACT FIRMLY SEATED AGAINST CABLE DIELECTRIC AND CRIMP CONTACT CABLE INNER IN PLACE. CONDUCTOR CRIMP DIE 2598-5379-54 CABLE JACKET CABLE OUTER CONDUCTOR DIELECTRIC BOTTOM HERE FERRULE CENTER CONTACT 2000 Tyco Electronics Corporation, Harrisburg, PA. This controlled document is subject to change. TOOLING ASSISTANCE CENTER 1-800-722-1111 1 of 2 All International Rights Reserved. For latest revision call the AMP FAX* number. AMP FAX/PRODUCT INFO 1-800-622-6752 *Trademark Dimensions are in inches. LOC B SMA Straight Cable Connectors 408-4736 4.0 CRIMP CABLE TO INNER SLEEVE. 4.1 INSERT CABLE SUB-ASSEMBLY INTO HOUSING SUB-ASSEMBLY AND SEAT FIRMLY. 4.2 SLIDE OUTER SLEEVE OVER FLARED PORTION OF OUTER CONDUCTOR. 3 HOLD CABLE FIRMLY SEATED AND Y, L CABLE A CRIMP OUTER SLEEVE IN PLACE. 4 TRIM AND REMOVE EXCESS OUTER HOUSING f 4 SUB-ASSEMBLY CONDUCTOR STRANDS. SOR ASSEMBLY \ rERRULE CRIMP DIE PER TABLE REF PLANE#] CONTACT 8 ~| DIELECTRIC 5.0 INSPECTION OF COMPLETED Td BE ASSEMBLY . BELOW SHE ZB ate o00/.010 5.1 ADHERENCE TO ASSEMBLY STEPS BELOW THE DIELECTRIC GIVEN SHOULD YIELD TOLERANCES BELOW THE SHOWN. REF PLANE he .075/.100 CONTACT JACK INTERFACE REF PLANE * PLUG NTERFACE CONNECTOR NO.| TYPE CRIMP DIE HEX SIZE | DIM "A" CABLE TYPE 22351-7316-xX_ [PLUG | 2098-0323-54 151 .320 | RD-316 DOUBLE BRAID 2231-7341-xX_ [PLUG | 5698-5015-54 NO. B 213 315 | RG-142. RG-55. RG-225. RG-400 2231-7388-Xx% |PLUG | 5698-5015-54 NO. C 128 .320 | RG-174, RG-188, RG-316 22354-7316-xX [JACK | 2098-0323-54 151 .325 | RD-3146 DOUBLE BRAID 2234-7341-XX_ [JACK | 5698-5015-54 NO. B 213 315 [RG-142, RG-55, RG-225, RG-400 2234-7388-XX_ | JACK | 5698-5015-54 NO. C 128 .325 | RG-174. RG-188. RG-316 NOTE: CRIMPING TO SOLID CENTER CONDUCTOR CABLES IS NOT RECOMMENDED 20f2 Rev O